DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 1 of 11

Description Power Range
The DigiFlex

Performance (DP) Series digital servo

drives are designed to drive brushed and brushless
servomotors. These fully digital drives operate in
torque, velocity, or position mode and employ Space
Vector Modulation (SVM), which results in higher bus
voltage utilization and reduced heat dissipation
compared to traditional PWM. The drive can be
configured for a variety of external command signals.
Commands can also be configured using the drives
built-in Motion Engine, an internal motion controller
used with distributed motion applications. In addition
to motor control, these drives feature dedicated and
programmable digital and analog inputs and outputs to
enhance interfacing with external controllers and
devices.
This DP Series drive features a single RS-232/RS-485
interface used for drive configuration and setup. Drive
commissioning is accomplished using DriveWare

7,
available for download at www.a-m-c.com.
All drive and motor parameters are stored in non-
volatile memory.
Peak Current 60 A (42.4 ARMS)
Continuous Current 30 A (21.2 ARMS)
Supply Voltage 100 - 240 VAC


Features

Four Quadrant Regenerative Operation
Space Vector Modulation (SVM) Technology
Fully Digital State-of-the-art Design
Programmable Gain Settings
Fully Configurable Current, Voltage, Velocity and
Position Limits
PIDF Velocity Loop
PID + FF Position Loop
Compact Size, High Power Density
16-bit Analog to Digital Hardware
Built-in brake/shunt regulator
Internal brake/shunt resistor
On-the-Fly Mode Switching
On-the-Fly Gain Set Switching



MODES OF OPERATION
Current
Position
Velocity
COMMAND SOURCE
PWM and Direction
Encoder Following
Over the Network
10 V Analog
24V Step and Direction
Indexing
Jogging
FEEDBACK SUPPORTED
Resolver
10 VDC Position
Auxiliary Incremental Encoder
Tachometer (10 VDC)
INPUTS/OUTPUTS
3 High Speed Captures
4 Programmable Analog Inputs (16-bit/12-bit
Resolution)
3 Programmable Digital Inputs (Differential)
7 Programmable Digital Inputs (Single-Ended)
4 Programmable Digital Outputs (Single-Ended)

COMPLIANCES & AGENCY APPROVALS
UL
cUL
CE Class A (LVD)
CE Class A (EMC)
RoHS

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 2 of 11

BLOCK DIAGRAM

SELECT
TX/TX
I
/
O

I
n
t
e
r
f
a
c
e
I
/
O

I
n
t
e
r
f
a
c
e
Drive
Logic
RS232/485
Interface
CONTROL MODULE
RX/RX
TX+
RX+
ISO GND
PAI-1,4 +(REF+)
PAI-1,4 (REF)
PDI-1,2,3,4,5,6,7
(STEP / DIR / CAP-A)
INPUT COMMON
PDI-8,9,10 +(PWM+/
DIR+/ AUX ENC A,B,I +/
CAP-B,C+)
PDO-1,2,3,4
OUTPUT COMMON
5k
+5V
10k
+5V
10k
2.5k
20k
20k
20k
PAI-2,3
SGN GND
PAI-2: 33k
PAI-3: 500k
3.75K
PDI-8,9,10 (PWM /
DIR / AUX ENC A,B,I /
CAP-B,C)
OUTPUT PULL-UP
M
o
t
o
r

F
e
e
d
b
a
c
k
M
o
t
o
r

F
e
e
d
b
a
c
k
ENC A,B,I +OUT
ENC A,B,I OUT
REF OUT +
REF OUT
SIN,COS +
SIN,COS
DC+
MOTOR A
MOTOR B
MOTOR C
EXT
POWER MODULE
Power Stage
Logic Power
L1
L2
L3
LOGIC+
LOGIC
Shunt Reg.
Fuse
Fuse
Fuse
Fuse
10 (200W)
INT
DC+
DC-

Information on Approvals and Compliances

US and Canadian safety compliance with UL 508c, the industrial standard for power conversion electronics. UL
registered under file number E140173. Note that machine components compliant with UL are considered UL
registered as opposed to UL listed as would be the case for commercial products.

Compliant with European CE for both the Class A EMC Directive 2004/108/EC on Electromagnetic Compatibility
(specifically EN 61000-6-4:2007 and EN 61000-6-2:2005) and LVD requirements of directive 2006/95/EC
(specifically EN 60204-1:2006), a low voltage directive to protect users from electrical shock.

RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being
manufactured in electrical and electronic equipment.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 3 of 11

SPECIFICATIONS
Power Specifications
Description Units Value
Rated Voltage VAC (VDC) 240 (339)
AC Supply Voltage Range VAC 100 - 240
AC Supply Minimum VAC 90
AC Supply Maximum VAC 264
AC Input Phases
1
- 3
AC Supply Frequency Hz 50 - 60
DC Supply Voltage Range
2
VDC 127 - 373
DC Bus Over Voltage Limit VDC 429
DC Bus Under Voltage Limit VDC 55
Logic Supply Voltage VDC 20 - 30 (@ 850 mA)
MaximumPeak Output Current
3
A (Arms) 60 (42.4)
MaximumContinuous Output Current A (Arms) 30 (21.2)
Max. Continuous Output Power @ Rated Voltage
4
W 6840
Max. Continuous Power Dissipation @ Rated Voltage W 360
Internal Bus Capacitance F 1650
External Shunt Resistor MinimumResistance 10
MinimumLoad Inductance (Line-To-Line)
5
H 600
Switching Frequency kHz 20
MaximumOutput PWM Duty Cycle % 100
Internal Shunt Fuse Rating A 5 A time-delay fuse
AC Line Fuse Rating A 20 A fast-acting fuses
Low Voltage Supply Outputs - +5 VDC (250 mA)
Control Specifications
Description Units Value
Communication Interfaces - RS-485/232
Command Sources -
10 V Analog, 24V Step and Direction, Encoder Following, Over the Network, PWM and Direction,
Indexing, J ogging
Feedback Supported - 10 VDC Position, Auxiliary Incremental Encoder, Resolver, Tachometer (10 VDC)
Commutation Methods - Sinusoidal
Modes of Operation - Current, Position, Velocity
Motors Supported - Closed Loop Vector, Single Phase (Brushed, Voice Coil, Inductive Load), Three Phase (Brushless)
Hardware Protection -
40+Configurable Functions, Over Current, Over Temperature (Drive & Motor), Over Voltage, Short
Circuit (Phase-Phase & Phase-Ground), Under Voltage
Programmable Digital Inputs/Outputs (PDIs/PDOs) - 10/4
Programmable Analog Inputs/Outputs (PAIs/PAOs) - 4/0
Primary I/O Logic Level - 24 VDC
Current Loop Sample Time s 50
Velocity Loop Sample Time s 100
Position Loop Sample Time s 100
Resolver Reference/Excitation Signal Vrms 4 Vrms @ 5 kHz
Expected Resolver Transformation Ratio Vrms 0.5
Feedback Resolution / Emulated Encoder Resolution
6
bit High Resolution Setting: 14, Low Resolution Setting: 12
MaximumMotor Speed Per Feedback Resolution RPM High Resolution Setting: 5000, Low Resolution Setting: 20000
Internal Shunt Regulator - Yes
Internal Shunt Resistor - Yes
Mechanical Specifications
Description Units Value
Agency Approvals - CE Class A (EMC), CE Class A (LVD), cUL, RoHS, UL
Size (H x W x D) mm(in) 234.7 x 161.8 x 151.3 (9.2 x 6.4 x 6)
Weight g (oz) 4495 (158.6)
Heatsink (Base) Temperature Range
7
C (F) 0 - 75 (32 - 167)
Storage Temperature Range C (F) -40 - 85 (-40 - 185)
FormFactor - Panel Mount
Cooling System - Natural Convection
IP Rating - IP10
+24V LOGIC Connector - 2-port, 5.08 mmspaced, enclosed, friction lock header with threaded flange
AUX ENCODER Connector - 15-pin, high-density, male D-sub
COMM Connector - 9-pin, female D-sub
DC BUS / BRAKE RESISTOR Connector - 5-contact, 13 mmspaced, dual-barrier terminal block
FEEDBACK Connector - 15-pin, high-density, female D-sub
I/O Connector - 26-pin, high-density, female D-sub
MOTOR POWER / DC BUS Connector - 5-contact, 13 mmspaced, dual-barrier terminal block
POWER Connector - 5-contact, 13 mmspaced, dual-barrier terminal block
Notes
1. Can operate on single-phase VAC if peak/cont. current ratings are reduced by at least 30%.
2. Large inrush current may occur upon initial DC supply connection to DC Bus.
3. Capable of supplying drive rated peak current for 2 seconds with 10 second foldback to continuous value. Longer times are possible with lower current limits.
4. P = (DC Rated Voltage) * (Cont. RMS Current) * 0.95.
5. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements.
6. Higher and lower resolution options are available. Contact Applications Engineering for more information.
7. Additional cooling and/or heatsink may be required to achieve rated performance.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 4 of 11

PIN FUNCTIONS
+24V LOGIC - Logic Power Connector
Pin Name Description / Notes I/O
1 LOGIC GND Logic Supply Ground GND
2 LOGIC PWR Logic Supply Input I

AUX ENCODER - Auxiliary Feedback Connector
Pin Name Description / Notes I/O
1 RESERVED Reserved -
2 RESERVED Reserved -
3 RESERVED Reserved -
4 PDI-8 +(PWM+/ AUX ENC A+/ CAP-B+) Programmable Digital Input or PWM or Auxiliary Encoder or High Speed Capture (For
Single-Ended Signals Leave Negative Terminal Open)
I
5 PDI-8 - (PWM- / AUX ENC A- / CAP-B-) I
6 PDI-9 +(DIR+/ AUX ENC B+/ CAP-C+) Programmable Digital Input or Direction Input or Auxiliary Encoder or High Speed Capture
(For Single-Ended Signals Leave Negative Terminal Open)
I
7 PDI-9 - (DIR- / AUX ENC B- / CAP-C-) I
8 PDI-10 +
Programmable Digital Input (For Single-Ended Signals Leave Negative Terminal Open)
I
9 PDI-10 - I
10 SGN GND Signal Ground SGND
11 SGN GND Signal Ground SGND
12 SGN GND Signal Ground SGND
13 +5V OUT +5V Encoder Supply Output (Short Circuit Protected) O
14 PAI-4 +
Differential Programmable Analog Input (12-bit Resolution)
I
15 PAI-4 - I

COMM - RS232/RS485 Communication Connector
Pin Name Description / Notes I/O
1 SELECT RS232/485 selection. Pull to ground (CN1-5) for RS485. I
2 RS232 TX / RS485 TX- Transmit Line (RS-232 or RS-485) O
3 RS232 RX / RS485 RX- Receive Line (RS-232 or RS-485) I
4 RESERVED Reserved -
5 ISO GND Isolated Signal Ground IGND
6 RS485 TX+ Transmit Line (RS-485) O
7 RESERVED Reserved -
8 RS485 RX+ Receive Line (RS-485) I
9 RESERVED Reserved -

DC BUS / BRAKE RESISTOR - Power Connector
Pin Name Description / Notes I/O
1 HIGH VOLTAGE
DC Bus Output
O
2 POWER GND PGND
3 EXT External Brake Resistor Connection. -
4 DC+ Brake Resistor DC+. Connection for brake resistor. O
5 INT Internal Brake Resistor. J umper to Brake Resistor DC+to activate. -

FEEDBACK - Feedback Connector
Pin Name Description / Notes I/O
1 RESERVED Reserved -
2 RESERVED Reserved -
3 RESERVED Reserved -
4 REF OUT +
Resolver Reference/Excitation Output
O
5 REF OUT - O
6 SIN+
Resolver Sine Input
I
7 SIN- I
8 COS+
Resolver Cosine Input
I
9 COS- I
10 RESERVED Reserved -
11 RESERVED Reserved -
12 SGN GND Signal Ground SGND
13 +5V OUT +5V Encoder Supply Output (Short Circuit Protected) O
14 PAI-3 Programmable Analog Input (12-bit Resolution) I
15 RESERVED Reserved -

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 5 of 11

I/O - Signal Connector
Pin Name Description / Notes I/O
1 PDO-1 Isolated Programmable Digital Output O
2 OUTPUT COMMON Digital Output Common OGND
3 PDO-2 Isolated Programmable Digital Output O
4 PAI-1 +(REF+)
Differential Programmable Analog Input or Reference Signal Input (16-bit Resolution)
I
5 PAI-1 - (REF-) I
6 PAI-2 Programmable Analog Input (12-bit Resolution) I
7 SGN GND Signal Ground SGND
8 OUTPUT PULL-UP Digital Output Pull-Up For User Outputs I
9 PDI-5 Isolated Programmable Digital Input I
10 PDO-3 Isolated Programmable Digital Output O
11 PDI-1 Isolated Programmable Digital Input I
12 PDI-2 Isolated Programmable Digital Input I
13 PDI-3 Isolated Programmable Digital Input I
14 PDO-4 Isolated Programmable Digital Output O
15 INPUT COMMON Digital Input Common (Can Be Used To Pull-Up Digital Inputs) IGND
16 SGN GND Signal Ground SGND
17 PDI-4 (STEP) Isolated Programmable Digital Input or Step I
18 PDI-6 (DIR) Isolated Programmable Digital Input or Direction I
19 PDI-7 (CAP-A) Isolated Programmable Digital Input or High Speed Capture I
20 ENC A+OUT
Emulated Encoder Channel A Output
O
21 ENC A- OUT O
22 ENC B+OUT
Emulated Encoder Channel B Output
O
23 ENC B- OUT O
24 ENC I+OUT
Emulated Encoder Index Output
O
25 ENC I- OUT O
26 SGN GND Signal Ground SGND

MOTOR POWER / DC BUS - Power Connector
Pin Name Description / Notes I/O
1 MOTOR A Motor Phase A O
2 MOTOR B Motor Phase B O
3 MOTOR C Motor Phase C O
4 POWER GND Power Ground (Isolated From Signal Ground) PGND
5 HIGH VOLTAGE DC Power Input I

POWER - Power Connector
Pin Name Description / Notes I/O
1 L1
AC Supply Input (Three Phase)
I
2 L2 I
3 L3 I
4 PE Protective Earth Ground -
5 RESERVED Reserved -
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 6 of 11

HARDWARE SETTINGS
Switch Functions
Switch Description
Setting
On Off
1
Bit 0 of binary RS-485 drive address. Does not affect RS-232
settings.
1 0
2
Bit 1 of binary RS-485 drive address. Does not affect RS-232
settings.
1 0
3
Bit 2 of binary RS-485 drive address. Does not affect RS-232
settings.
1 0
4
Bit 3 of binary RS-485 drive address. Does not affect RS-232
settings.
1 0
5
Bit 4 of binary RS-485 drive address. Does not affect RS-232
settings.
1 0
6
Bit 5 of binary RS-485 drive address. Does not affect RS-232
settings.
1 0
7
Bit 0 of drive RS-485 baud rate setting. Does not affect RS-232
settings.
1 0
8
Bit 1 of drive RS-485 baud rate setting. Does not affect RS-232
settings.
1 0
Additional Details
The drive can be configured to use the address and/or bit rate stored in non-volatile memory by setting the address and/or bit
rate value to 0. Use the table below to map actual bit rates to a bit rate setting.

Baud Rate (kbps) Value For Bit Rate Setting
Load from non-volatile memory 0
9.6 1
38.4 2
115.2 3
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 7 of 11

MECHANICAL INFORMATION
+24V LOGIC - Logic Power Connector
Connector Information 2-port, 5.08 mm spaced, enclosed, friction lock header with threaded flange
Mating Connector
Details Phoenix Contact: P/N 1777808
Included with Drive Yes
LOGIC GND 1
LOGIC PWR 2


AUX ENCODER - Auxiliary Feedback Connector
Connector Information 15-pin, high-density, male D-sub
Mating Connector
Details
TYCO: Plug P/N 1658681-1; Housing P/N 5748677-1; Terminals P/N 1658686-2 (loose) or
1658686-1 (strip)
Included with Drive No
PDI-8 - (PWM- / AUX ENC A- / CAP-B-) 5
PDI-8 +(PWM+/ AUX ENC A+/ CAP-B+) 4
PAI-4 - 15
PAI-4 + 14
+5V OUT 13
SGN GND 12
SGN GND 11
SGN GND 10
PDI-9 +(DIR+/ AUX ENC B+/ CAP-C+) 6
PDI-10 - 9
PDI-10 + 8
PDI-9 - (DIR- / AUX ENC B- / CAP-C-) 7


COMM - RS232/RS485 Communication Connector
Connector Information 9-pin, female D-sub
Mating Connector
Details
TYCO: Plug P/N 205204-4; Housing P/N 5748677-1; Terminals P/N 1658540-5 (loose) or
1658540-4 (strip)
Included with Drive No
SELECT 1
RS232 TX / RS485 TX- 2
RS232 RX / RS485 RX- 3
ISO GND 5
RS485 TX+ 6
RS485 RX+ 8


ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 8 of 11

DC BUS / BRAKE RESISTOR - Power Connector
Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block
Mating Connector
Details Not applicable
Included with Drive Not applicable
HIGH VOLTAGE 1
POWER GND 2
EXT 3
DC+ 4
INT 5


FEEDBACK - Feedback Connector
Connector Information 15-pin, high-density, female D-sub
Mating Connector
Details
TYCO: Plug P/N 748364-1; Housing P/N 5748677-1; Terminals P/N 1658670-2 (loose) or
1658670-1 (strip)
Included with Drive No
REF OUT + 4
REF OUT - 5
SGN GND 12
+5V OUT 13
PAI-3 14
SIN+ 6
SIN- 7
COS+ 8
COS- 9


I/O - Signal Connector
Connector Information 26-pin, high-density, female D-sub
Mating Connector
Details
TYCO: Plug P/N 1658671-1; Housing P/N 5748677-2; Terminals P/N 1658670-2 (loose) or
1658670-1 (strip)
Included with Drive No
PDO-1 1
2
3
4
5
6
8
9
7
PDO-4 14
PDI-1 11
PDI-2 12
PDI-3 13
PDO-3 10
INPUT COMMON 15
PDI-4 (STEP) 17
PDI-6 (DIR) 18
SGN GND 16
OUTPUT COMMON
PDI-5
OUTPUT PULL-UP
SGN GND
PAI-2
PAI-1 - (REF-)
PAI-1 +(REF+)
PDO-2
PDI-7 (CAP-A) 19
ENC I+OUT 24
ENC B+OUT 22
ENC A+OUT 20
ENC A- OUT 21
ENC B- OUT 23
ENC I- OUT 25
SGN GND 26


ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 9 of 11

MOTOR POWER / DC BUS - Power Connector
Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block
Mating Connector
Details Not applicable
Included with Drive Not applicable
MOTOR A 1
MOTOR B 2
MOTOR C 3
POWER GND 4
HIGH VOLTAGE 5


POWER - Power Connector
Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block
Mating Connector
Details Not applicable
Included with Drive Not applicable
L1 1
L2 2
L3 3
PE 4

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 10 of 11

MOUNTING DIMENSIONS

ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By:

DigiFlex

Performance Servo Drive DPRAHIR-060A400

Release Date:
9/27/2012
Revision:
2.02
ADVANCED Motion Controls 3805 Calle Tecate, Camarillo, CA, 93012
ph# 805-389-1935 fx# 805-389-1165 www.a-m-c.com
Page 11 of 11

PART NUMBERING INFORMATION
-
Drive Series
DigiFlex Performance
Communication
Command Inputs
R P D I N A E 5 1 0 A 0 0 4 Example:
DP
RS232/RS485 R
CANopen or RS232 C
SynqNet Q
Analog (10V)
No Step &Direction
AN
Analog (10V)
Low Voltage Step &Direction (5V)
AL
Analog (10V)
High Voltage Step &Direction (24V)
AH
No Analog
Low Voltage Step &Direction (5V)
NL
No Analog, No Step &Direction
(Communication Interface Only)
NN
Digital I/O
Isolated (24V) I
TTL (5V) Non-Isolated T
Motor Feedback
Incremental Encoder and/or Halls E
Resolver R
Absolute Sin/Cos (Hiperface &Endat) A
Sin/Cos with Halls S
Max DC Bus Voltage (VDC)
80 080
200 200
400 400
800 800
AC Input
+24VDC User Logic Supply Required
A
AC Input Single Phase Only
+24VDC User Logic Supply Required
S
DC Input
Both Logic Supply Options (Internal or User)
B
DC Input
Logic Supply Required
L
15 015
16 016
20 020
25 025
30 030
40 040
60 060
100 100
-
Code used to identify customer
specials
Power and Logic Supply
Peak Current (A0 to Peak)
Customer Special
EtherCAT E
Universal (Halls, Inc. Enc., Abs. Enc.,
1Vp-p Sin/Cos Enc.)
U

DigiFlex Performance series of products are available in many configurations. Note that not all possible part number
combinations are offered as standard drives. All models listed in the selection tables of the website are readily available, standard
product offerings.

ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for OEMs with volume
requests. Our Applications and Engineering Departments will work closely with your design team through all stages of
development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quick-
turn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease
your costs and time-to-market while increasing system quality and reliability. Feel free to contact Applications Engineering for
further information and details.

Examples of Customized Products
Optimized Footprint Tailored Project File
Private Label Software Silkscreen Branding
OEM Specified Connectors Optimized Base Plate
No Outer Case Increased Current Limits
Increased Current Resolution Increased Voltage Range
Increased Temperature Range Conformal Coating
Custom Control Interface Multi-Axis Configurations
Integrated System I/O Reduced Profile Size and Weight

Available Accessories
ADVANCED Motion Controls offers a variety of accessories designed to facilitate drive integration into a servo system.
Visit www.a-m-c.com to see which accessories will assist with your application design and implementation.



Drive(s)


Filter Cards


To Motor





All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document.
ELECTROMATE
Toll Free Phone (877) SERVO98
Toll Free Fax (877) SERV099
www.electromate.com
[email protected]
Sold & Serviced By: