MELSEC FX Series

Programmable Logic Controllers

User's Manual
(Hardware)
FX2N-16CCL-M
CC-Link Master Module
INDUSTRIAL AUTOMATION
MITSUBISHI ELECTRIC
MITSUBISHI ELECTRIC
Art. no.: 168595
15 03 2007
JY992D93101
Version D
Foreword
This manual contains text, diagrams and explanations which will guide the reader in the
correct installation and operation of the FX2N-16CCL-M CC-Link System Master Block. It
should be read and understood before attempting to install or use the unit.
Further information can be found in the FX1N, FX2N, FX2NC Series Hardware Manual, FX
Series Programming Manual .
If in doubt at any stage of the installation of FX2N-16CCL-M CC-Link System Master Block
always consult a professional electrical engineer who is qualified and trained to the local
and national standards that applies to the installation site.
If in doubt about the operation or use of FX2N-16CCL-M CC-Link System Master Block
please consult the nearest Mitsubishi Electric distributor.
This manual is subject to change without notice.
FX2N-16CCL-M CC-Link System Master Block
i
FX2N-16CCL-M
Control & Communication-Link
System Master Block
USERS MANUAL
Manual number : JY992D93101
Manual revision : D
Date : March 2007
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block
ii
FAX BACK
Mitsubishi has a world wide reputation for its efforts in continually developing and pushing back
the frontiers of industrial automation. What is sometimes overlooked by the user is the care
and attention to detail that is taken with the documentation. However, to continue this process
of improvement, the comments of the Mitsubishi users are always welcomed. This page has
been designed for you, the reader, to fill in your comments and fax them back to us. We look
forward to hearing from you.
Fax numbers: Your name: ...................................................
Mitsubishi Electric.... .....................................................................
America (01) 847-478-2253 Your company: .............................................
Australia (02) 638-7072 .....................................................................
Germany (0 21 02) 4 86-1 12 Your location:................................................
Spain (34) 93-589-1579 .....................................................................
United Kingdom (01707) 278-695
Please tick the box of your choice
What condition did the manual arrive in? Good Minor damage Unusable
Will you be using a folder to store the manual?Yes No
What do you think to the manual presentation?Tidy Unfriendly
Are the explanations understandable? Yes Not too bad Unusable
Which explanation was most difficult to understand: ..................................................................
....................................................................................................................................................
Are there any diagrams which are not clear? Yes No
If so,which: ..................................................................................................................................
What do you think to the manual layout? Good Not too bad Unhelpful
If there one thing you would like to see improved, what is it?.....................................................
....................................................................................................................................................
....................................................................................................................................................
Could you find the information you required easily using the index and/or the contents, if
possible please identify your experience: ...................................................................................
....................................................................................................................................................
....................................................................................................................................................
....................................................................................................................................................
....................................................................................................................................................
Do you have any comments in general about the Mitsubishi manuals? .....................................
....................................................................................................................................................
....................................................................................................................................................
....................................................................................................................................................
....................................................................................................................................................
Thank you for taking the time to fill out this questionnaire. We hope you found both the product
and this manual easy to use.
FX2N-16CCL-M CC-Link System Master Block
iii
FX2N-16CCL-M CC-Link System Master Block
iv
FX2N-16CCL-M CC-Link System Master Block
v
Guidelines for the Safety of the User and Protection of the FX2N-16CCL-M CC-
Link System Master Block
This manual provides information for the use of the FX2N-16CCL-M CC-Link System Master
Block. The manual has been written to be used by trained and competent personnel. The
definition of such a person or persons is as follows;
a) Any engineer who is responsible for the planning, design and construction of automatic
equipment using the product associated with this manual should be of a competent
nature, trained and qualified to the local and national standards required to fulfill that
role. These engineers should be fully aware of all aspects of safety with regards to
automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and
qualified to the local and national standards required to fulfill that job. These engineers
should also be trained in the use and maintenance of the completed product. This
includes being completely familiar with all associated documentation for the said product.
All maintenance should be carried out in accordance with established safety practices.
c) All operators of the completed equipment (see Note) should be trained to use this
product in a safe manner in compliance to established safety practices. The operators
should also be familiar with documentation which is associated with the operation of the
completed equipment.
Note : Note: the term completed equipment refers to a third party constructed device which
contains or uses the product associated with this manual.
Notes on the Symbols Used in this Manual
At various times throughout this manual certain symbols will be used to highlight points of
information which are intended to ensure the users personal safety and protect the integrity of
equipment. Whenever any of the following symbols are encountered its associated note must
be read and understood. Each of the symbols used will now be listed with a brief description of
its meaning.
Hardware Warnings
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property
damage.
3) Indicates a point of further interest or further explanation.
Software Warnings
4) Indicates special care must be taken when using this element of software.
5) Indicates a special point which the user of the associate software element should
be aware of.
6) Indicates a point of interest or further explanation.
FX2N-16CCL-M CC-Link System Master Block
vi
Under no circumstances will Mitsubishi Electric be liable responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
All examples and diagrams shown in this manual are intended only as an aid to
understanding the text, not to guarantee operation. Mitsubishi Electric will accept no
responsibility for actual use of the product based on these illustrative examples.
Please contact a Mitsubishi Electric distributor for more information concerning applications
in life critical situations or high reliability.
FX2N-16CCL-M CC-Link System Master Block
vii
Contents
1. Introduction............................................................................................1-1
1.1 Associated Manuals ............................................................................................ 1-1
1.2 General Names and Abbreviations...................................................................... 1-2
2. Overview ...............................................................................................2-1
2.1 Overview of CC-Link System............................................................................... 2-1
2.2 Overview of CC-Link Master Block FX2N-16CCL-M............................................ 2-1
2.3 Characteristics..................................................................................................... 2-2
2.4 Major Differences from A/QnA/Q Series.............................................................. 2-6
3. System Configuration............................................................................3-1
3.1 Total Configuration .............................................................................................. 3-1
3.2 Applicable PLC.................................................................................................... 3-2
3.3 Configuration Example ........................................................................................ 3-3
3.3.1 Example of maximum configuration, when using a FX2N PLC.................................. 3-3
3.3.2 Scan time of PLC and connection of two or more master blocks.............................. 3-4
3.3.3 Example of connection of two or more FX Series PLCs............................................ 3-5
3.3.4 Example of connection to the CC-Link system for the A/QnA/Q Series.................... 3-6
3.4 Number of Occupied Stations and Station numbers as well as Number
of Modules and Number of Stations .................................................................... 3-7
3.5 System Equipment List ........................................................................................ 3-8
3.6 Precautions When Configuring the System....................................................... 3-11
3.6.1 Wiring of power supply ............................................................................................ 3-11
3.6.2 Wiring of remote I/O modules.................................................................................. 3-12
4. Specification..........................................................................................4-1
4.1 External Dimensions / Part Names...................................................................... 4-1
4.2 Power Supply Specifications ............................................................................... 4-1
4.3 General Specification .......................................................................................... 4-1
4.4 Performance Specification................................................................................... 4-2
4.4.1 Maximum transmission distance ............................................................................... 4-4
4.5 Dedicated CC-Link Cable .................................................................................... 4-5
4.6 Buffer Memory ..................................................................................................... 4-6
4.6.1 Buffer memory list ..................................................................................................... 4-7
4.6.2 Parameter information area....................................................................................... 4-8
4.6.3 I/O signals to PLC ................................................................................................... 4-12
4.6.4 I/O signal details...................................................................................................... 4-15
4.6.5 Master block control signals .................................................................................... 4-22
4.6.6 Remote input (RX)................................................................................................... 4-23
4.6.7 Remote output (RY) ................................................................................................ 4-25
4.6.8 Remote register (RWw) Master station --> Remote device station ..................... 4-27
4.6.9 Remote register (RWr) Master station <-- Remote device station....................... 4-29
4.6.10 Link special relay (SB) and link special register (SW) ............................................. 4-31
FX2N-16CCL-M CC-Link System Master Block
viii
Contents
5. Functions...............................................................................................5-1
5.1 Function List ........................................................................................................ 5-1
5.2 Communication between Master Station and Remote I/O Stations..................... 5-2
5.3 Communication between Master Station and Remote Device Stations .............. 5-4
5.4 Communication in Compound System................................................................ 5-9
5.5 Reserved Station Function ................................................................................ 5-14
5.6 Error Invalid Station Function ............................................................................ 5-15
5.7 Data Link Status Setting against Error in Master Station PLC .......................... 5-16
5.8 Setting of Input Data Status from Data Link Faulty Station ............................... 5-17
5.9 Module Reset Function from Sequence Program ............................................. 5-18
5.10 Data Link Stop/Restart ...................................................................................... 5-19
5.11 RAS Function .................................................................................................... 5-20
5.11.1 Automatic return function ........................................................................................ 5-20
5.11.2 Slave station cutoff function .................................................................................... 5-20
5.11.3 Station number overlap check function ................................................................... 5-21
5.12 Temporary Error Invalid Station Specification Function..................................... 5-22
5.12.1 I/O status when temporary error invalid stations are specified................................ 5-22
5.12.2 Link special relays and registers (SB and SW) related to temporary error
invalid station specification function ........................................................................ 5-22
5.12.3 Temporary error invalid station specification procedure.......................................... 5-24
6. Data Link Processing Time ...................................................................6-1
6.1 Status of Each Station when an Error has Occurred........................................... 6-1
6.2 Link Scan Time.................................................................................................... 6-3
6.3 Transmission Delay Time .................................................................................... 6-4
6.3.1 Master station remote I/O station.......................................................................... 6-4
6.3.2 Master station remote device station.................................................................... 6-5
7. Parameter Setting .................................................................................7-1
7.1 Procedure from Parameter Setting to Data Link Startup ..................................... 7-1
7.1.1 Relationship among buffer memory, EEPROM and internal memory ....................... 7-1
7.1.2 Procedure from parameter setting to data link startup .............................................. 7-3
7.2 Parameter Setting Items...................................................................................... 7-4
7.3 Setting from Sequence Program......................................................................... 7-5
7.3.1 Setting and operation using the buffer memory ........................................................ 7-5
7.3.2 Parameter registration procedure to the EEPROM and operation based on
parameters registered in the EEPROM..................................................................... 7-7
7.3.3 Program example .................................................................................................... 7-10
FX2N-16CCL-M CC-Link System Master Block
ix
Contents
8. Data Link Procedure..............................................................................8-1
8.1 Data Link Procedure............................................................................................ 8-3
8.2 Name of Each Part and Settings ......................................................................... 8-4
8.3 Master Block Status Check (Hardware Test)....................................................... 8-8
8.4 Module Wiring with Dedicated CC-Link Cables................................................... 8-9
8.5 T-shaped Branch Connection Using Dedicated CC-Link Cables ...................... 8-10
8.5.1 System configuration with T-shaped branch connection......................................... 8-10
8.5.2 T-shaped branch communication specification list .................................................. 8-11
8.6 Switch Settings .................................................................................................. 8-12
8.6.1 Station number setting (master station, remote I/O stations and remote
device stations) ...................................................................................................... 8-12
8.6.2 Mode setting............................................................................................................ 8-14
8.6.3 Transmission speed setting..................................................................................... 8-14
8.6.4 Condition setting...................................................................................................... 8-14
8.7 Connection Status Check (Line Test) ................................................................ 8-15
8.7.1 Check of connection status and communication status with remote stations
(line test 1).............................................................................................................. 8-15
8.7.2 Check of communication status with specific remote station (line test 2)................ 8-16
8.8 Parameter Check (Parameter Verification Test)................................................ 8-17
9. Programming.........................................................................................9-1
9.1 Precautions in Programming ............................................................................... 9-1
9.2 Programming Procedure ..................................................................................... 9-3
9.2.1 Communication between master station and remote I/O stations............................. 9-3
9.2.2 Communication between master station and remote device stations ....................... 9-4
9.2.3 Communication in compound system ....................................................................... 9-5
9.3 Link Special Relay/Register (SB/SW).................................................................. 9-6
9.3.1 Link special relay (SB) list ......................................................................................... 9-6
9.3.2 Link special register (SW) ....................................................................................... 9-10
10.Communication between Master Station and Remote I/O Stations ...10-1
10.1 System Configuration ........................................................................................ 10-1
10.1.1 Setting of master station.......................................................................................... 10-1
10.1.2 Setting of remote I/O station.................................................................................... 10-2
10.2 Creating a Program........................................................................................... 10-3
10.2.1 Program for parameters .......................................................................................... 10-3
10.2.2 Program for communication .................................................................................... 10-5
10.3 Execution of Data Link....................................................................................... 10-7
10.3.1 Confirmation of operation by LED indication........................................................... 10-7
10.3.2 Confirmation of operation by program..................................................................... 10-8
11.Communication between Master Station and Remote Device Stations.. 11-1
11.1 System Configuration ........................................................................................ 11-1
11.1.1 Setting of master station.......................................................................................... 11-1
11.1.2 Setting of remote device station.............................................................................. 11-2
11.2 Creating a Program........................................................................................... 11-3
11.2.1 Program for parameters .......................................................................................... 11-3
11.2.2 Program for communication .................................................................................... 11-5
11.3 Execution of Data Link....................................................................................... 11-9
11.3.1 Confirmation of operation by LED indication........................................................... 11-9
11.3.2 Confirmation of operation by program................................................................... 11-10
FX2N-16CCL-M CC-Link System Master Block
x
Contents
12.Communication in Compound System...............................................12-1
12.1 System configuration ......................................................................................... 12-1
12.1.1 Setting of master station.......................................................................................... 12-1
12.1.2 Setting of remote I/O station.................................................................................... 12-2
12.1.3 Setting of remote device station.............................................................................. 12-2
12.2 Creating a Program........................................................................................... 12-3
12.2.1 Program for parameters .......................................................................................... 12-3
12.2.2 Program for communication .................................................................................... 12-5
12.3 Execution of Data Link....................................................................................... 12-8
12.3.1 Confirmation of operation by LED indication........................................................... 12-8
12.3.2 Confirmation of operation by program..................................................................... 12-9
13.Troubleshooting..................................................................................13-1
13.1 Verification when Trouble Occurs...................................................................... 13-2
13.2 Troubleshooting when ERR LED is Flashing in Master Station......................... 13-5
13.3 Error Codes ....................................................................................................... 13-7
13.4 LED Indication Status ...................................................................................... 13-11
13.4.1 When data link is normal ....................................................................................... 13-11
13.4.2 When a cable is broken......................................................................................... 13-11
13.4.3 When a cable is short-circuited ............................................................................. 13-12
13.4.4 When link is stopped in the master station............................................................ 13-12
13.4.5 When power supply to a remote I/O station is turned off ...................................... 13-13
13.4.6 When power supply to a remote device station is turned off ................................. 13-13
13.4.7 When a station number overlaps........................................................................... 13-14
13.4.8 When the transmission speed is incorrectly set .................................................... 13-14
13.4.9 When the switch setting is changed during data link............................................. 13-15
13.4.10When data link is started with a switch set outside the allowable range .............. 13-15
13.4.11When a remote I/O station is not set in the parameter
(and set as a reserved station) .............................................................................. 13-16
13.4.12When a remote device station is not set in the parameter
(and set as a reserved station) .............................................................................. 13-16
14.Appendix ............................................................................................14-1
Introduction 1
1-1
1. Introduction
1.1 Associated Manuals
: Indispensable manual
: Manual required depending on equipment used
Table 1.1:
Manual name Manual number Description
FX2N-16CCL-M
Users Guide
JY992D93201
(packed with product)
Describes the name of each part and handling of
the CC-Link master block FX2N-16CCL-M.
FX1S/FX1N/FX2N/FX2NC
Programming Manual
JY992D88101
(separate volume)
Explains the instructions in the FX1S/FX1N/FX2N/
FX2NC Series PLC.
FX3U/FX3UC
Programming Manual
-Basic & Applied
Instruction Edition
JY997D16601
(separate volume)
Explains the instructions in the FX3U/FX3UC
Series PLC.
FX
1N
Hardware Manual
JY992D89301
(packed with product)
Describes the contents related to the hardware
such as specification, wiring and mounting of the
FX
1N
Series PLC.
FX2N Hardware Manual
JY992D66301
(packed with product)
Describes the contents related to the hardware
such as specification, wiring and mounting of the
FX2N Series PLC.
FX
3U
Hardware Manual
JY997D18801
(packed with product)
Describes the name of each part and handling of
the FX3U Series PLC.
FX
3U
Series Users
Manual
- Hardware Edition
JY997D16501
(separate volume)
Describes the contents related to the hardware
such as specification, wiring and mounting of the
FX3U Series PLC.
FX2NC Hardware Manual
JY992D76401
(packed with product)
Describes the contents related to the hardware
such as specification, wiring and mounting of the
FX2NC Series PLC.
FX2N-32CCL
Users Manual
JY992D71801
(packed with product)
Describes programming and handling of the CC-
Link interface block FX2N-32CCL.
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Introduction 1
1-2
1.2 General Names and Abbreviations
Unless otherwise specified, this manual uses the general names and abbreviations shown in
the table below to describe the CC-Link system master block FX2N-16CCL-M.
Table 1.2:
General name/
abbreviation
Description
FX2N-16CCL-M Abbreviation of the CC-Link system master block FX2N-16CCL-M.
Cyclic transmission
Transmission method to periodically communicate the contents of remote
I/Os and remote registers.
Master station
Station which controls the data link system.
One master station is required in one system.
Local station
Station equipped with CPU which can communicate with the master station
and other local stations in the CC-Link system of the MELSEC-A/QnA/Q
Series.
Remote I/O station
Remote station which deals with bit information only (to execute I/Os with
external equipment) (such as AJ65BTB1-16D and AJ65SBTB1-16D).
Remote device station
Remote station which deals with bit information and word information
(to execute I/Os with external equipment and exchange analog data)
(such as FX2N-32CCL, AJ65BT-64AD, AJ65BT-64DAV and AJ65BT-64DAI).
Remote station
General name for remote I/O station and remote device station.
Controlled by the master station.
Intelligent device station
Station which can execute transient transmission (such as AJ65BT-R2) in the
CC-Link system of the MELSEC-A/QnA/Q Series.
Standby master station
Station for backup which takes over data link control when the master station
is disconnected due to abnormality in the PLC CPU, the power supply, etc. in
the CC-Link system of the MELSEC-A/QnA/Q Series.
Master block Abbreviation for FX2N-16CCL-M.
SB
Link special relay (for CC-Link).
1-bit information which indicates the operation status and the data link status
of the master/local station.
Represented in "SB" for convenience.
SW
Link special register (for CC-Link).
16-bit information which indicates the operation status and the data link
status of the master/local station.
Represented in "SW" for convenience.
RX
Remote input (for CC-Link)
1-bit information input from a remote station to the master station.
Represented in "RX" for convenience.
RY
Remote output (for CC-Link)
1-bit information output from the master station to a remote station.
Represented in "RY" for convenience.
RWw
Remote register (write area for CC-Link)
16-bit information output from the master station to a remote device station.
Represented in "RWw" for convenience.
RWr
Remote register (read area for CC-Link)
16-bit information input from a remote device station to the master station.
Represented in "RWr" for convenience.
Overview 2
2-1
2. Overview
This chapter describes the overview of the CC-Link system master block FX2N-16CCL-M for
the FX Series PLC.
The abbreviated term "CC-Link" stands for "Control & Communication-Link". "CC-Link" is used
hereafter in this manual.
2.1 Overview of CC-Link System
The CC-Link system connects distributed I/O modules, special function modules, etc. with
dedicated cables, and controls such modules from the PLC CPU.
1) By distributing each module to the facility equipment such as conveyor lines and machines,
the wiring conservation of the entire system can be accomplished.
2) Simple, high speed communication can be accomplished with modules that handle the ON/
OFF data such as I/Os or the numeric data.
3) Connections can be made to different types of devices made by partner manufacturers,
giving flexibility to the system.
2.2 Overview of CC-Link Master Block FX2N-16CCL-M
The CC-Link master block FX2N-16CCL-M is a special extension block which assigns an FX
Series PLC as the master station of the CC-Link system.
1) Remote I/O stations and remote device stations can be connected to the master station (FX
Series PLC).
2) By using the CC-Link interface block FX2N-32CCL, two or more FX Series PLCs can be
connected as remote device stations to configure a simple distributed system.
Master station : Station which controls the data link system
Remote I/O station : Remote station which handles only the 1-bit information
Remote device station: Remote station which handles both bit information and word information
Remote I/O station
FX1N/2N/3U Series PLC
CC-Link master block
FX2N-16CCL-M
Remote device station
Remote I/O station
Remote device station
CC-Link interface block
FX2N-32CCL
FX0N/1N/2N /2NC
Series PLC
Partner manufacturers
product
/2NC
/3U
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Overview 2
2-2
2.3 Characteristics
This section describes the characteristics of the CC-Link.
1) Communication with remote I/O station
The switch ON/OFF status and the lamp ON/OFF status are communicated using remote
inputs (RX) and remote outputs (RY).
Remote inputs (RX) and remote outputs (RY) are assigned to the buffer memory (BFM)
numbers built in the FX2N-16CCL-M. (Refer to Subsections 4.6.6 and 4.6.7.)
*1 Devices which can be specified as FROM instruction transfer destinations or TO
instruction transfer sources can be used.
2) Communication with remote device station
Handshake signals (such as initial requests and error occurrence flags) are communicated
with remote device stations using remote inputs (RX) and remote outputs (RY).
The setting data and other data are communicated with remote device stations using
remote registers (RWw and RWr).
Remote inputs (RX), remote outputs (RY) and remote registers (RWw and RWr) are
assigned to the buffer memory (BFM) numbers built in the FX2N-16CCL-M. (Refer to Sub-
sections 4.6.8 and 4.6.9.)
*1 Devices which can be specified as FROM instruction transfer destinations or TO
instruction transfer sources can be used.
Internal relay
*1
Internal relay
*1
Remote input
RX(BFM)
Remote output
RY(BFM)
FROM
instruction
TO instruction
Input
Output
Link scan
Link scan
FX1N/2N/2NC
Series PLC
Master station
FX2N-16CCL-M
Remote I/O station
Internal relay
KnM
*1
Internal relay
KnM
*1
Remote input
RX(BFM)
Remote
registers
RWw(BFM)
FROM
instruction
TO instruction
Remote input
RX
Remote output
RY
Link scan
Link scan
Data register
D
*1
Data register
D
*1
Remote
registers
RWr(BFM)
TO instruction
FROM
instruction
Remote
registers
RWw
Remote
registers
RWr
Link scan
Link scan
Voltmeter
Master station
FX2N-16CCL-M
Remote device station
FX1N/2N/2NC
Series PLC
Remote output
RY(BFM)
FX2N-16CCL-M CC-Link System Master Block Overview 2
2-3
3) System down prevention (slave station cutoff function)
Because the system employs the bus method, even if there is a remote station which goes
down due to power OFF, etc., it will not affect the communication with other functioning
stations.
Also, in the case of a module equipped with a 2-piece terminal block, the module can be
replaced during data link. (Turn off the power of a module to be replaced, then replace it.)
However, if a cable is broken, data link is disabled in all stations. (Refer to Section 5.11.2.)
4) Reserved station function
By setting a station which is not actually connected now (which is planned for connection in
the future) as a reserved station, the station will not be handled as a faulty station.
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1
Remote I/O station
(occupies 1 station)
Station No. 2
Remote
device
station
(occupies 4
stations)
Station No. 3
Remote I/O station
(occupies 1 station)
Station No. 7
Remote
device
station
(occupies 4
stations)
Station No. 8
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1
Remote I/O station
(occupies 1 station)
Station No. 2
Remote
device
station
(occupies 4
stations)
Station No. 3
Remote I/O station
(occupies 1 station)
Station No. 7
Remote
device
station
(occupies 4
stations)
Station No. 8
Data link continues.
Faulty
station
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1
Remote I/O station
(occupies 1 station)
Station No. 2
Remote
device
station
(occupies 4
stations)
(Reserved station)
Station No. 3
Remote I/O station
(occupies 1 station)
Station No. 7
(Reserved station)
Station No. 8
Stations planned for
connection in the future
Remote I/O station
(occupies 1 station)
FX2N-16CCL-M CC-Link System Master Block Overview 2
2-4
5) Error invalid station function
A station which cannot execute the data link because the power is turned off, etc. can be
excluded from being handling as a "data link faulty station" in the master station.
Be careful, however, because errors will not be detected.
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1
Remote I/O station
(occupies 1 station)
Station No. 2
Remote
device
station
(occupies 4
stations)
Station No. 3
Remote I/O station
(occupies 1 station)
Station No. 7
Remote
device
station
(occupies 4
stations)
Station No. 8
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1
Remote I/O station
(occupies 1 station)
Station No. 2
Remote
device
station
(occupies 4
stations)
Station No. 3
Remote I/O station
(occupies 1 station)
Station No. 7
Remote
device
station
(occupies 4
stations)
Station No. 8
Not handled as a data
link faulty station.
Stations to be set as "error
invalid station"
FX2N-16CCL-M CC-Link System Master Block Overview 2
2-5
6) Parameter registration to the EEPROM
By registering the parameters to the EEPROM in advance, the parameter settings do not
have to be executed at each startup (power OFF ON) of the master station.
The data stored in the EEPROM remains stored even if the power of the module is turned
off.
7) Data link status setting for a case where an error occurs in the CPU in the master station (PLC)
The data link status can be set (to "stop" or "continue") for a case where an "operation stop
error" such as a PLC program error occurs in the master station.
When an "operation continue error" such as a battery error occurs, the data link continues
without regard to the setting.
8) Status setting of the input data from a data link faulty station
The data input (received) from a data link faulty station can be cleared or kept (in the status
right before an error occurs).
9) Module reset function from a sequence program
When the switch setting is changed or an error occurs in the module, the module can be
reset from a sequence program without resetting the PLC.
(This excludes when the module has a module faulty input (BFM No. AH b0 is ON)).
10)RAS function
a) Automatic return function
When a station was disconnected from the link due to power OFF, etc. then returns to
normal status, the station can join the data link again automatically.
b) Link status check
Using the link special relay (SB) and the link special register (SW) in the buffer memory,
the current data link status can be checked.
c) Diagnosis function
Using the switch setting, the hardware and the cable wiring can be checked.
PLC CPU
SETM
TO
SETM
BFM#AH b10
BFM#AH b8
Parameter
information area
Buffer memory
Master station
E
2
PROM
Internal
memory
The data link is
executed using the
parameters registered
in the internal memory.

FX2N-16CCL-M CC-Link System Master Block Overview 2

2-6
2.4 Major Differences from A/QnA/Q Series
Table 2.1:
Item FX Series master block A/QnA/Q Series master module
Applicable function Master station
Master station
Local station
Standby master station
Number of connected
modules
Remote I/O stations: 7 max.
Remote device stations: 8 max.
Remote I/O stations: 64 max.
Remote device stations: 42 max.
Local/standby master/intelligent
device stations: 26 max.
Maximum link points per
station
Remote I/Os (RX/RY): 32
Remote registers (RWr/RWw): 4

Scan cycle Asynchronous mode
Asynchronous mode
Synchronous mode
Automatic refresh Not provided Provided
Intelligent device station Cannot be connected. Can be connected.
System Configuration 3
3-1
3. System Configuration
This chapter describes the system configuration for the CC-link in which an FX Series PLC
functions as the master station.
3.1 Total Configuration
Up to 7 remote I/O stations and up to 8 remote device stations can be connected to one FX
Series PLC functioning as the master station. (Each of the numbers "7" and "8" excludes the
master station.)
However, the following conditions must be satisfied in connection:
When using a FX3U PLC
1) Total number of I/O points
2) Total number of points of the remote I/O station
3) Maximum number of input/output points
4) Connection of remote device stations (up to 8 stations)
Up to 8 remote device stations can be connected without regard to the number of points shown in
1), 2) and 3) above.
Number of I/O points in PLC (including vacant
numbers and extension I/O points)
points
Number of points occupied by FX2N-16CCL-M 8 points
Total number of points occupied by other
special extension PLCs
points
[Total]
points
256
32 Number of remote I/O stations points
[Total]
points
224
Total number of I/O points 1) points
Total number of points of the remote I/O
station 2)
points
[Total]
points
384
Number of remote device stations occupying 1
station
1 station modules stations
Number of remote device stations occupying 2
stations
2 stations modules stations
Number of remote device stations occupying 3
stations
3 stations modules stations
Number of remote device stations occupying 4
stations
4 stations modules stations
[Grand total]
stations
8
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-2
When using a FX2N, FX2NC or a FX1N PLC
1) Connection of remote I/O stations (up to 7 stations)
2) Connection of remote device stations (up to 8 stations)
Up to 8 remote device stations can be connected without regard to the number of remote I/O
stations shown in 1).
3.2 Applicable PLC
Number of I/O points in PLC (including vacant
numbers and extension I/O points)
points
Number of points occupied by FX2N-16CCL-M 8 points
Total number of points occupied by other
special extension PLCs
points
32 Number of remote I/O stations points
[Total]

256: FX2N/2NC Series PLC
128: FX1N Series PLC
Number of remote device stations occupying 1
station
1 station modules stations
Number of remote device stations occupying 2
stations
2 stations modules stations
Number of remote device stations occupying 3
stations
3 stations modules stations
Number of remote device stations occupying 4
stations
4 stations modules stations
[Grand total]
stations
8
Table 3.1:
Series name Applicable version
FX1N
Manufacturers serial number: 08**** or later
(Approximate production period: August, 2000 or later)
FX2N
System version V 2.20 or later
(Approximate production period: July, 2000 or later)
FX2NC
(FX2NC-CNV-IF is required.)
FX3U All
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-3
3.3 Configuration Example
3.3.1 Example of maximum configuration, when using a FX2N PLC
In the FX2N Series PLC, when a 16-point basic module and the master block FX2N-16CCL-M
are connected, up to 7 remote I/O stations can be connected (7 is the maximum number).
As to remote device stations, up to 8 stations can be connected without regard to the number
of remote I/O stations.
256 - 248 = 8 points (remaining number of I/O points)
In the configuration above, up to 8 I/O points or
special modules corresponding to up to 8 points can
added.
Number of I/O points in PLC (including vacant
numbers and extension I/O points)
16 points
Number of points occupied by FX
2N
-16CCL-M 8 points
Total number of points occupied by other
special extension PLCs
0 points
32 Number of remote I/O stations 224 points
248 points
256 (FX2N)
Main unit
FX2N-16M
16 points
Master block
FX2N-16CCL-M
8 points
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
Occupies 1
station
(Station No. 0)
Terminal resistor
[7 remote I/O stations] 32 points x 7 stations
8 remote device stations
Occupies 1
station
Terminal resistor
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-4
3.3.2 Scan time of PLC and connection of two or more master blocks
1) Measured scan time
- Configuration:
[FX2N Series PLC main unit]+[FX2N-16CCL-M]+[7 remote I/O stations]+[8 remote device
stations]
- Number of link device points: 110 words
The scan time in the configuration above is 125 ms.
2) Handling when two or more master blocks are connected
Remote I/O stations can be connected only to the first master block.
To the second and later master blocks, only remote device stations (up to 8 stations) can be
connected.
- Configuration:
[FX2N Series PLC main unit]
+[FX2N-16CCL-M (first module)]+[7 remote I/O stations]+[8 remote device stations]
+[FX2N-16CCL-M (second module)]+[8 remote device stations]
- Number of link device points: 206 words
The scan time in the configuration above is 233 ms.
3) Caution
If the total scan time in the PLC exceeds 200 ms, a watchdog timer error occurs. In this
case, change the value of the special data register D8000 in the PLC to prolong the
watchdog timer time.
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-5
3.3.3 Example of connection of two or more FX Series PLCs
When connecting two or more FX Series PLCs in the CC-Link system, connect CC-Link
interface blocks FX2N-32CCL on the child station side and use them as remote device stations.
Main unit
FX1N,FX2N,FX3U,
FX2NC *
CC-Link
master block
FX2N-16CCL-M
I/O extension
Special extension
I/O extension
Special extension
[Remote I/O stations]
The number of connected
modules vary depending on the
contents of extension in the PLC.

Main unit
FX0N,FX1N,FX2N,FX3U,
FX2NC *
CC-Link interface block
FX2N-32CCL
(Set to occupy 4 stations.)
Main unit
FX0N,FX1N,FX2N,FX3U,
FX2NC *
CC-Link interface block
FX2N-32CCL
Main unit
FX0N,FX1N,FX2N,FX3U,
FX2NC *
CC-Link interface block
FX2N-32CCL
Main unit
FX0N,FX1N,FX2N,FX3U,
FX2NC *
CC-Link interface block
FX2N-32CCL
(Set to occupy 2 stations.)
(Set to occupy 1 station.)
(Set to occupy 1 station.)
Terminal resistor
Terminal resistor
[Remote device stations]
In this example, four CC-Link interface blocks FX2N-32CCL
which function as remote device stations are connected.
The number of stations occupied by the FX2N-32CCL can
be selected inside the range from 1 to 4.
When each FX2N-32CCL is set to occupy 1 station, up to
8 FX Series PLCs can be connected.
* When an FX2NC Series PLC is connected, the interface
FX2NC-CNV-IF is required.
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-6
3.3.4 Example of connection to the CC-Link system for the A/QnA/Q Series
When connecting the CC-Link system for the A/QnA/Q Series and the CC-Link system for the
FX Series, provide the CC-Link interface FX2N-32CCL in the connection area as shown in the
figure below.
Main unit
FX1N,FX2N,
FX3U,FX2NC *
CC-Link master block
FX2N-16CCL-M
CC-Link interface
FX2N-32CCL
C
P
U
Master station
QJ61BT11
A1SJ61QBT11
AJ61QBT11
A1SJ61BT11
AJ61BT11
CC-Link master
block for the A/QnA/
Q Series
Local station
Remote I/O station
Remote device
station
Master station
Terminal
resistor
Main unit
FX0N,FX1N,FX2N,
FX3U,FX2NC *
CC-Link interface
FX2N-32CCL
Remote I/O station
Main unit
FX0N,FX1N,FX2N,
FX3U,FX2NC *
CC-Link interface
FX2N-32CCL
Terminal resistor
CC-Link master
block for the FX
Series
Provide the CC-Link
interface FX2N-32CCL in
the connection area.
Terminal resistor
Terminal resistor
* When an FX2NC Series PLC is connected, the interface FX2NC-CNV-IF is required.
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-7
3.4 Number of Occupied Stations and Station numbers as well as Number of
Modules and Number of Stations
This section describes the relationship between the number of occupied stations and the
station as well as between the number of modules and the number of stations.
1) Number of occupied stations
The number of stations occupied by each remote I/O station or remote device station is
shown in Table 3.2.
2) Station number
When the number of stations occupied by every station module is 1, assign consecutive
section numbers beginning with 1 (1, 2, 3, ...).
If there is a station module occupying 2 or more stations, the number of occupied stations
should be taken into account when the station are assigned.
3) Number of modules and number of stations
The number of modules indicates the number of physical modules.
The number of stations indicates the number of stations occupied by all modules as
described in 1).
In the example of system configuration shown in 2), the number of modules is 5 and the
number of stations is 9.
Table 3.2:
Module Number of occupied stations
Remote I/O station (module with 16 or 32 points) 1
Remote device station
FX2N-32CCL 1 to 4 (selectable)
AJ65BT-64AD 2
AJ65BT-64DAV 2
AJ65BT-64DAI 2
AJ65BT-D62
AJ65BT-D62D(S1)
4
A852GOT 2 or 4
Master
station
Station No. 1
Remote I/O
station (occupies
1 station)
Station No. 3
Remote
device station
FX2N-32CCL
(occupies 4
stations)
Station No. 4
Remote I/O
station (occupies
1 station)
Station No. 8
Remote
device station
FX2N-32CCL
(occupies 1
station)
Station No. 9
Remote
device station
(occupies 2
stations)
Station
No. 1
Station
No. 2
Station
No. 3
Station
No. 4
Station
No. 5
Station
No. 6
Station
No. 7
Station
No. 8
Station
No. 9
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-8
3.5 System Equipment List
The table below shows the list of equipment constructing the CC-Link for the FX Series PLC.
Table 3.3:
Product name Model name Description
Number of
occupied
stations
Station
type
Master block FX2N-16CCL-M Master block for the FX1N/FX2N/FX3U/FX2NC Series
Master
station
FX Series PLC
connection
block
FX2N-32CCL
Interface block for connection of the FX0N/FX1N/FX2N/
FX3U/FX2NC Series
One station occupies 32 input points and 32 output
points.
However, 16 points of the last station is used as the
system area.
One station occupies 4 RWw and 4 RWr.
1 to 4
Remote
device
station
Remote I/O
module
AJ65BTB1-16D
1-line, 16-point DC input module (sink/source shared)
24V DC, 7 mA, 16 points/common
1
Remote
I/O
station
AJ65BTB2-16D
2-line, 16-point DC input module (sink/source shared)
24V DC, 7 mA, 16 points/common
AJ65BTC1-32D
1-line, 32-point DC input module (sink/source shared)
24V DC, 7 mA, 32 points/common
AJ65BTB1-16T
1-line, 16-point transistor output module (sink)
12/24V DC, 0.5 A/point, 4 A/common, 8 points/
common
AJ65BTB2-16T
2-line, 16-point transistor output module (sink)
12/24V DC, 0.5 A/point, 4 A/common, 8 points/
common
AJ65BTC1-32T
1-line, 32-point transistor output module (sink)
12/24V DC, 0.1 A/point, 2 A/common, 32 points/
common
AJ65BTB2-16R
2-line, 16-point contact output module
24V DC/240V AC, 2 A/point, 8 A/common, 8 points/
common
AJ65BTB1-16DT
I/O module
Input: 1-line, 8 DC input points (sink)
24V DC, 7 mA, 8 points/common
Output: 1-line, 8 transistor output points (sink)
12/24V DC, 0.5 A/point, 8 points/common
AJ65BTB2-16DT
I/O module
Input: 2-line, 8 DC input points (sink)
24V DC, 7 mA, 8 points/common
Output: 2-line, 8 transistor output points (sink)
12/24V DC, 0.5 A/point, 4 A/common, 8 points/
common
AJ65BTB2-16DR
I/O module
Input: 2-line, 8 DC input points (sink/source shared)
24V DC, 7 mA, 8 points/common
Output: 2-line, 8 contact output points
24V DC/240V AC, 2 A/point, 8 A/common, 8
points/common
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-9
Small type
remote I/O
module
AJ65SBTB1-8D
1-line, 8-point DC input module (sink/source shared)
24V DC, 7 mA, 8 points/common
1
Remote
I/O
station
AJ65SBTB1-16D
1-line, 16-point DC input module (sink/source shared)
24V DC, 7 mA, 16 points/common
AJ65SBTB1-16D1
1-line, 16-point DC input module (sink/source shared)
24V DC, 5 mA, 16 points/common, high-speed
response type
AJ65SBTB1-32D
1-line, 32-point DC input module (sink/source shared)
24V DC, 7 mA, 32 points/common
AJ65SBTB1-32D1
1-line, 32-point DC input module (sink/source shared)
24V DC, 5 mA, 32 points/common, high-speed
response type
AJ65SBTC1-32D
1-line, 32-point DC input module (sink/source shared)
24V DC, 5 mA, 32 points/common
AJ65SBTC1-32D1
1-line, 32-point DC input module (sink/source shared)
24V DC, 5 mA, 32 points/common, high-speed
response type
AJ65SBTC4-16D
2-, 3-, 4-line, 16-point DC input module (sink/source
shared)
24V DC, 5 mA, 16 points/common
AJ65SBTW4-16D
Waterproof, 4-line, 16-point DC input module (sink/
source shared)
24V DC, 5 mA, 16 points/common, waterproof type
AJ65SBTB1-8T
1-line, 8-point transistor output module (sink)
12/24V DC, 0.5 A/point, 2.4 A/common, 8 points/
common
AJ65SBTB1-16T
1-line, 16-point transistor output module (sink)
12/24V DC, 0.5 A/point, 3.6 A/common, 16 points/
common
AJ65SBTB1-32T
1-line, 32-point transistor output module (sink)
12/24V DC, 0.5 A/point, 4.8 A/common, 32 points/
common
AJ65SBTC1-32T
1-line, 32-point transistor output module (sink)
12/24V DC, 0.1 A/point, 32 points/common
AJ65SBTC1-32DT
I/O module
Input: 1-line, 16 DC input points (sink)
24V DC, 5 mA, 32 points/common
Output: 1-line, 16 transistor output points (sink)
24V DC, 0.1 A/point, 32 points/common
AJ65SBTC1-32DT1
I/O module, high-speed response type
Input: 1-line, 16 DC input points (sink)
24V DC, 5 mA, 32 points/common
Output: 1-line, 16 transistor output points (sink)
24V DC, 0.1 A/point, 32 points/common
AJ65SBTC4-16DT
I/O module
Input: 2-, 3-, 4-line, 8 DC input points (sink)
24V DC, 5 mA, 16 points/common
Output: 2-, 3-, 4-line, 8 transistor output points (sink)
24V DC, 0.5 A/point, 16 points/common
Table 3.3:
Product name Model name Description
Number of
occupied
stations
Station
type
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-10
Small type
remote I/O
module
AJ65SBTW4-16DT
I/O module, waterproof type
Input: Waterproof, 4-line, 8 DC input points (sink)
24V DC, 5 mA, 16 points/common
Output: Waterproof, 4-line, 8 transistor output points
(sink)
24V DC, 0.5 A/point, 16 points/common
1
Remote
I/O
station
Analog-digital
conversion
module
AJ65BT-64AD
4-channel input
Analog input: -10 to +10 V, -20 to +20 mA
Digital output: -2,000 to +2,000, 0 to +4,000
2
Remote
device
station
Digital-analog
conversion
module
AJ65BT-64DAV
4-channel voltage output
Digital input: -2,000 to +2,000
Analog output: -10 to +10 V
AJ65BT-64DAI
4-channel current output
Digital input: 0 to +4,000
Analog output: +4 to +20 mA
High-speed
counter
module
AJ65BT-D62
24-bit binary, 5/12/24V DC input type
200 kPPS, 2 channels
4
AJ65BT-D62D
24-bit binary, 5/12/24V DC input type
400 kPPS, 2 channels
AJ65BT-D62D-S1
24-bit binary, differential input type
400 kPPS, 2 channels
Thermocouple
temperature
input unit
AJ65BT-68TD
8 channels of temperature input to connect
thermocouple
Platinum
resistance
thermometer
bulb Pt100
temperature
input unit
AJ65BT-64RD3
4 channels of temperature input to connect Pt100
(3-line type)
AJ65BT-64RD4
4 channels of temperature input to connect Pt100
(4-line type)
ID interface
module
AJ65BT-D32ID2 Number of connectable readers/writers: 2
Graphic
operation
terminal
A852GOT-LWD/LBD
Black-and-white liquid crystal type (2 colors)
Resolution: 320 240 dots
Number of touch keys: 300
2 or 4 A852GOT-SWD/SBD
Color STN liquid crystal type (8 colors)
Resolution: 320 240 dots
Number of touch keys: 300
Communication
module for CC-
Link connection
A8GT-J61BT15
Interface module for the CC-Link system for the GOT
(for remote device station)
Table 3.3:
Product name Model name Description
Number of
occupied
stations
Station
type
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-11
3.6 Precautions When Configuring the System
3.6.1 Wiring of power supply
When the FX2N-16CCL-M is supplied with 24V DC, the external power supply of FX2N-16CCL-M
needs to be supplied at same time as the PLC main unit. See examples below.
1) When the 24V DC service power supply of a PLC with an AC power supply is used, or when
a stabilized power supply unit is used.
2) When a PLC of DC power supply type is used.
L 24+ N 24V 0V
PLC main unit
24-
FX2N-16CCL-M
L 24+ N
PLC main unit
24-
FX2N-16CCL-M
N
L
24-
24+ Stabilized
power
supply
+ 24+ -
PLC main unit
24-
FX2N-16CCL-M
N
L
24-
24+ Stabilized
power
supply
24V DC
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-12
3.6.2 Wiring of remote I/O modules
Design the system with the following considerations to prevent erroneous inputs from remote I/O
modules:
1) Timing of power ON and power OFF
Turn on the power of remote I/O modules first, then start the data link.
Stop the data link first, then turn off the power of remote I/O modules.
2) Momentary power failure in remote I/O modules
When momentary power failure occurs in the power (24V DC) supplied to remote I/O
modules, erroneous input may occur.
a) Cause for erroneous input due to momentary power failure
The remote I/O module hardware converts the module power (24V DC) into 5V DC
inside the module, then uses the 5V DC.
When momentary power failure occurs in a remote I/O module, the following condition
occurs:
(Time until 5V DC inside remote I/O module turns off)
> (Input module ON OFF response time)
Therefore, erroneous input is caused when refresh is executed within the period of time
indicated by in the diagram below.
Remote I/O module
(power supply status)
During operation
During stop
Master module (data
link status)
ON
OFF
Data link start Data link stop
Remote I/O module
(internal 5V DC)
Remote I/O module
(module power supply and input
external power supply)
Because the input external power supply is
turned off, the input (X) turns off after the
"input module ON OFF response time".
Input (X)

FX2N-16CCL-M CC-Link System Master Block System Configuration 3

3-13
b) Countermeasures against erroneous input
Wire the module power supply, the stabilized power supply and the input external power
supply from the same power source.
For DC input
For AC input
Remarks
When supplying power from one power source to multiple remote I/O modules,
select cables and perform wiring with considerations to the voltage drop caused by
the cables.
Connections can be established if the receiving port voltage of the remote I/O
module is within the specification range of the remote I/O module.
Main unit
M
a
s
t
e
r

b
l
o
c
k
Stabilized
power supply
24V DC
Module power
supply
Remote I/O module
Input external
power supply
Main unit
M
a
s
t
e
r

b
l
o
c
k
Stabilized
power supply
24V DC
Module power
supply
Remote I/O module
Input external
power supply
Stabilized
power supply
Remote module Remote module
FX2N-16CCL-M CC-Link System Master Block System Configuration 3
3-14
MEMO
Specification 4
4-1
4. Specification
DESIGN PRECAUTIONS
Refer to Chapter 13 in this manual for the status of each station when a communication
error occurred in the data link.
When executing control (data changes) to an operating PLC, construct an interlock circuit in
the sequence program so that the entire system always works conservatively.
In addition, when executing control such as program changes and operation status changes
(status control) to an operating PLC, thoroughly read the manual and sufficiently confirm
safety in advance.
Especially in control from external equipment to a PLC in a remote place, problems in the
PLC may not be able to be handled promptly due to abnormality in data transfer.
Construct an interlock circuit in the sequence program. At the same time, determine the
actions in the system between the external equipment and the PLC CPU for protection
against abnormalities in data transfer.
4.1 External Dimensions / Part Names
For the external dimensions and part names , refer to Section 8.2.
4.2 Power Supply Specifications
4.3 General Specification
Dielectric strength: 500 VAC for 1 minute (between the case and the PLC ground)
Other specification is equivalent to that of the PLC basic module.
Item Specification
24V DC external power supply Supplied from 24V DC (150 mA) external terminal block.
5V DC internal power supply
5V DC of PLC is not used.
(5V DC is changed from 24V DC external power supply.)
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-2
4.4 Performance Specification
Table 4.1:
Item Specification
Applicable function
Master station function (The local station and standby master station functions
are not provided.)
CC-Link version Ver.1.10
Transmission speed
Selectable (by rotary switch) among 156 kbps, 625 kbps, 2.5 Mbps, 5 Mbps
and 10 Mbps
Station number 0 (set by rotary switch)
Maximum total cable
length (maximum
transmission distance)
1,200 m maximum
Varies depending on the transmission speed. (Refer to Subsection 4.4.1.)
Maximum number of
connected modules
Remote I/O stations: 7 maximum (Each station occupies 32 I/O points of
the PLC.)
Remote device stations: 8 maximum (The following condition must be
satisfied.)
{(1a)+(2b)+(3c)+(4d)} 8
a: Number of remote device stations occupying 1 station
b: Number of remote device stations occupying 2 stations
c: Number of remote device stations occupying 3 stations
d: Number of remote device stations occupying 4 stations
Number of remote I/O stations + Number of remote device stations 15
"Maximum number of I/O points per system" below shall be satisfied.
For the system configuration calculation, refer to Chapter 3.
Maximum number of
I/O points per system
When using a FX3U PLC:
1) (Actual number of I/O points of PLC) +(Number of points occupied by
special extension blocks) + (Number of points occupied by
FX2N-16CCL-M: 8) 256 (FX3U Series PLC)
2) (32 x Number of remote I/O modules) 224 (FX3U Series PLC)
1) + 2) total number of points 384
When using a FX1N, FX2N or a FX2NC PLC:
Connection is allowed as far as the following condition is satisfied:
(Actual number of I/O points of PLC) + (Number of points occupied by
special extension blocks) + (Number of points occupied by FX2N-16CCL-
M: 8) + (32 Number of remote I/O modules) 256 (FX2N/2NC Series PLC)
or 128 (FX1N Series PLC)
For the system configuration calculation, refer to Chapter 3.
Number of link points
per station
Remote I/O station : Remote I/O = 32/32 (RX/RY) points
Remote device station: Remote I/O = 32/32 (RX/RY) points
Remote register = 4 (RWw) points
(master station remote device station)
Remote register = 4 (RWr) points
(remote device station master station)
Communication
method
Polling method
Synchronous method Frame synchronous method
Encoding method NRZI method
Transmission path
type
Bus (RS-485)
Transmission format In conformance to HDLC Standard
Error control method CRC(X
16
+X
12
+X
5
+1)
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-3
*1 Dedicated CC-Link cables and dedicated high-performance CC-Link cables cannot be
used at the same time. Only either type of cables are available.
Attach a terminal resistor in accordance with the cable type. (Refer to Section 8.4.)
*2 When an FX2NC Series PLC is connected, the interface FX2NC-CNV-IF is required.
Connection cable
Dedicated CC-Link cable/Dedicated high-performance CC-Link cable
*1
RAS function
Automatic return function
Slave station cutoff function
Error detection by link special relay/register
Number of times of
parameter registration
to EEPROM
Approximately 10,000 times
Connectable PLC
FX1N, FX2N (V 2.20 or later), FX3U and FX2NC (V 2.20 or later)
*2
Series PLC
Number of occupied
I/O points
8 I/O points of FX Series PLC (8 points in total. The ratio between inputs and
outputs is arbitrary.)
Communication with
PLC
By FROM/TO instructions via the buffer memory
Note
Scan method: Asynchronous mode
Automatic refresh: Not provided
Local station function: Not provided
Standby master station function: Not provided
Intelligent device station connection function: Not provided
This master block FX2N-16CCL-M and the AS-i maser block FX2N-32ASI-
M cannot be connected at the same time.
Operation indication
POWER: Lit while 24V DC is supplied from outside.
L RUN : Lit while communication is normal.
L ERR : Lit when communication error has occurred.
SD : Lit while data is being transmitted.
RD : Lit while data is being received.
24V DC external
power supply
Supplied from 24V DC (150 mA) external terminal block.
5V DC internal power
supply
5V DC is self-supplied. 5V DC of PLC is not used.
Accessories
Terminal resistor
For standard cable:
110 , 1/2 W (color cable: brown, brown and brown), 2 cables
For high performance cable:
130 , 1/2 W (color cable: brown, orange and brown), 2 cables
Special block number label
MASS (weight) 0.4kg (0.88lbs)
Table 4.1:
Item Specification
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-4
4.4.1 Maximum transmission distance
This section describes the relationship between the transmission speed and the maximum
transmission distance.
1) In the system consisting of only remote I/O stations and remote device stations
*1 Cable length between remote I/O or remote device stations
*2 Cable length between the master station and an adjacent station
Dedicated CC-Link cable (requiring terminal resistor of 110 )
Dedicated high-performance CC-Link cable (requiring terminal resistor of 130 )
Table 4.2:
Transmission
speed
Cable length between stations
Maximum
transmission
distance
*1 *2
156kbps
30 cm or more
1 m or more
1200m
625kbps 600m
2.5Mbps 200m
5Mbps
30 cm to 59 cm * 110m
60 cm or more 150m
10Mbps
30 cm to 59 cm * 50m
60 cm to 99 cm * 80m
1 m or more 100m
Table 4.3:
Transmission
speed
Cable length between stations
Maximum
transmission
distance
*1 *2
156kbps
30 cm or more 1 m or more
1200m
625kbps 900m
2.5Mbps 400m
5Mbps 160m
10Mbps 100m
Remote I/O station
or remote device
station
Master station
Remote I/O station
or remote device
station
Remote I/O station
or remote device
station
Remote I/O station
or remote device
station
*2 *2 *1 *1
Maximum transmission distance
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-5
Dedicated high-performance CC-Link cable (for the CC-Link system V 1.10)
(requiring terminal resistor of 130 )
When the entire system consists of only equipment and cables V 1.10, the following
advantages are offered.
1) The cable distance between two stations is defined to 20 cm or more in any condition.
2) Because the degree of freedom in the cable length is improved, the wiring work and the
system layout become easier.
3) Because excessive cable length does not have to be assured when modules are located
near each other, the space efficiency is improved.
4) Cables produced by diversified manufacturers can be used at the same time.
Example:
When remote I/O stations and remote device stations are connected with dedicated high-
performance CC-Link cables and the transmission speed is set to 10 Mbps, the maximum
transmission distance is "100 m".
4.5 Dedicated CC-Link Cable
Use dedicated CC-Link cables in the CC-Link system.
If any other cable is used, the performance of the CC-Link system cannot be guaranteed.
Table 4.4:
Transmission
speed
Cable length between stations
Maximum
transmission
distance
*1 *2
156kbps
20 cm or more
1200m
625kbps 900m
2.5Mbps 400m
5Mbps 160m
10Mbps 100m
Master station
Remote I/O
station
Remote device
station
Remote I/O
station
Remote I/O
station
Remote device
station

10th module 4th module 3rd module 2nd module 1st module
1m 50cm 35cm 50cm
100 m maximum
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-6
4.6 Buffer Memory
The buffer memory is used to swap data between the master block and the PLC.
In the PLC, the FROM/TO instructions are used to read/write data.
The contents of the buffer memory return to the default values when the power is turned off.
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-7
4.6.1 Buffer memory list
* Do not write to areas that are prohibited to use. Such write may cause errors.
Table 4.5:
BFM number
Item Description
Read/write
possibility
Reference
Hex. Dec.
#0H
#9H
#0
#9
Parameter
information area
Stores the information (parameters)
to execute the data link.
Read/write
enabled
4.6.2
#AH
#BH
#10
#11
I/O signal I/O signals to control the master block
Read/write
enabled
4.6.3
#CH
#1BH
#12
#27
Parameter
information area
Stores the information (parameters)
to execute the data link.
Read/write
enabled
4.6.2
#1CH
#1EH
#28
#30
Master block control
signal
Signals to control the master block
Read/write
enabled
4.6.5
#1FH
#31 (Prohibited to use)*
Write
disabled

#20H
#2FH
#32
#47
Parameter
information area
Stores the information (parameters)
to execute the data link.
Read/write
enabled
4.6.2
#30H
#DFH
#48
#223
(Prohibited to use)*
Write
disabled

#E0H
#FDH
#224
#253
Remote input (RX)
Stores the input status from a remote
station.
Read only 4.6.6
#FEH
#15FH
#254
#351
(Prohibited to use)*
Write
disabled

#160H
#17DH
#352
#381
Parameter
information area
Stores the output status to a remote
station.
Write only 4.6.7
#17EH
#1DFH
#382
#479
(Prohibited to use)*
Write
disabled

#1E0H
#21BH
#480
#539
(Prohibited to use)*
Stores the transmission data to a
remote station.
Write only 4.6.8
#21CH
#2DFH
#540
#735
(Prohibited to use)*
Write
disabled

#2E0H
#31BH
#736
#795
Remote register
(RWr)
(Master station: For
receiving)
Stores the received data from a
remote station.
Read only 4.6.9
#31CH
#5DFH
#796
#1503
(Prohibited to use)*
Write
disabled

#5E0H
#5FFH
#1504
#1535
Link special relay
(SB)
Stores the data link status.
Read/write
enabled
(write
disabled
depending
on device)
4.6.10
#600H
#7FFH
#1536
#2047
Link special register
(SW)
Stores the data link status. 9.3
#800H
#2048
(Prohibited to use)*
Write
disabled

~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
~~
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-8
4.6.2 Parameter information area
Set the conditions to perform the data link.
The contents of setting can be registered to the EEPROM.
* Do not write to areas that are prohibited to use. Such write may cause errors.
Table 4.6:
BFM
number
Item Description Default
Hex. Dec.
#00H #0 (Prohibited to use)*
#01H #1
Number of
connected modules
Set the number of connected
remote station modules
(including reserved stations).
8
#02H #2 Number of retries
Set the number of retries to a
faulty station.
3
#03H #3
Number of
automatic return
modules
Set the number of remote station
modules that can return to the
system during one link scan.
1
#04H
#05H
#4
#5
(Prohibited to use)*
#06H #6
Operation
specification against
CPU down
Specify the data link status when
an error occurs in the master
station PLC.
0 (stop)
#07H
#09H
#7
#9
(Prohibited to use)*
#CH
#FH
#12
#15
(Prohibited to use)*
#10H #16
Reserved station
specification
Set reserved stations. 0 (No specification)
#11H
#13H
#17
#19
(Prohibited to use)*
#14H #20
Error invalid station
specification
Specify error invalid stations. 0 (No specification)
#15H
#1BH
#21
#27
(Prohibited to use)*
#1CH #28
FROM/TO
instruction access
error judgement time
Set the FROM/TO instruction
access error judgement time
(unit: 10 ms).
200ms
#1DH #29
Access outside
allowable range
"1" is input when a non-
connectable station or address
is accessed.
0
#1EH #30 Model code
Model code specific to the FX2N-
16CCL-M
K7510
#1FH #31 (Prohibited to use)*
#20H
#2EH
#32
#46
Station information Set the connected station type.
Station type: Remote I/O station
Number of occupied stations: 1
Station number: 1 to 15
~~
~~
~~
~~
~~
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-9
a) Number of connected modules
Set the number of remote station modules (including reserved stations) connected to the
master station.
This is not a station count.
The setting range is "1 to 15 (modules)".
b) Number of retries
Set the number of retries to a remote station with a link data error.
The setting range is "1 to 7 (times)".
If a remote station cannot recover the normal data link after executing the specified
number of retries, the station is regarded as a "data link faulty station".
c) Number of automatic return modules
Set the number of remote station modules that can return to the system during one link
scan.
The setting range is "1 to 10 (modules)".
d) Operation specification for CPU shut down
Specify the data link status when an "operation stop error" occurs in the master station
PLC.
The setting range is "0 (stop)" and "1 (continue)".
e) Reserved station specification
Set remote stations which are included in the number of connected modules but are not
actually connected now so that such stations will not be handled as "data link faulty
stations"
1) When a connected remote station is set as a reserved station, the station cannot
execute any data link at all.
2) Set to ON the bits corresponding to the station numbers to be set as reserved.
For a remote station which occupies 2 or more stations, turn on only the bit for the
station Number set by the modules station number setting switch.
Numbers 1 to 15 indicate the station numbers in the table below.
Point
The station information (address 20H to 2EH) for the specified "number of connected
modules" becomes valid.
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 10H 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-10
Setting example:
When setting a remote device station with the station No. 4 and a remote station with the
station No. 9 as reserved in the system configuration below.
f) Error invalid station specification
Specify remote stations in which data link is disabled by power OFF, etc. so that they are
not handled as "data link faulty stations" by the master station. Be careful, however, for
errors will not be detected.
1) When the same station number is specified as a reserved station also, the reserved
station specification has the priority.
2) Set to ON the bits corresponding to the station numbers to be set as error invalid
stations.
For a remote station which occupies 2 or more stations, turn on only the bit for the
station number set by the modules station number setting switch.
Numbers 1 to 15 indicate the station numbers in the table below.
Setting example:
When setting a remote device station with the station No. 4 and a remote station with the
station No. 9 as invalid in the system configuration below.
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 10H 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 14H 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 14H 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0
Master
station
Remote station
(occupies 2
stations)
Station No. 1
Remote station
(occupies 1
station)
Station No. 3
Remote
device station
(occupies 4
stations)
Station No. 4
Remote station
(occupies 1
station)
Station No. 8 Station No. 9
Remote station
(occupies 1
station)
Stations to be connected in the future
Master
station
Remote station
(occupies 2
stations)
Station No. 1
Remote station
(occupies 1
station)
Station No. 3
Remote
device station
(occupies 4
stations)
Station No. 4
Remote station
(occupies 1
station)
Station No. 8 Station No. 9
Remote station
(occupies 1
station)
Set as error invalid stations
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-11
g) Station information
Set the station type for connected remote stations and reserved stations.
1) The figure below shows the data configuration to be set.
2) The table below shows the buffer memory address for each module.
For example, when setting for the 10th module, write the buffer memory address
"BFM#29H".
Setting example:
When connecting one remote I/O station and two remote device stations
Table 4.7:
Module
BFM number
Hex. Dec.
1st module #20H #32
2nd module #21H #33
3rd module #22H #34
4th module #23H #35
5th module #24H #36
6th module #25H #37
7th module #26H #38
8th module #27H #39
9th module #28H #40
10th module #29H #41
11th module #2AH #42
12th module #2BH #43
13th module #2CH #44
14th module #2DH #45
15th module #2EH #46
Station type
Number of occupied
stations
Station No.
b15 b12 ~ b11 b8 ~ b7 b0 ~
1: Occupies 1 station.
2: Occupies 2 stations.
3: Occupies 3 stations.
4: Occupies 4 stations.
1~15
(01H~0FH)
0: Remote I/O station
1: Remote device station
Master
station
Station No. 1
(occupies 1
station)
Remote I/O
station
Station No. 2
(occupies 2
stations)
Remote device
station
Station No. 4
(occupies 4
stations)
Remote device
station
1st module 2nd module 3rd module Station type
Number of
occupied
stations
Station No.
0H 1H 01H
1H 2H 02H
1H 4H 04H
BFM#20H
BFM#21H
BFM#22H
<System configuration example> <Station information setting>
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-12
4.6.3 I/O signals to PLC
This section describes I/O signals used to control the master block.
The signals used to control the master block are assigned to the buffer memory (BFM#AH and
BFM#BH) built in the FX2N-16CCL-M.
The buffer memory of the same number works differently between the time of read (when the
FROM instruction is used) and the time of write (when the TO instruction is used) as shown in
the table below.
The system automatically changes over these functions in accordance with the instruction
(FROM or TO).
The table below shows also the assignment of I/O numbers adopted in the A/QnA/Q Series
master module as reference. These I/O numbers are available only in the A/QnA/Q Series, and
are not available in the CC-Link system for the FX Series. When making a program, make sure
to specify bits of the buffer memory.
Table 4.8:
PLC Master block
Read (when FROM instruction is used)
BFM
number
Read
bit
Input signal name
Reference: Input number
in A/QnA/Q Series
BFM
#AH
(#10)
b0 Module error Xn0
b1 Data link status in host station Xn1
b2 Parameter setting status Xn2
b3 Data link status in other stations Xn3
b4 Module reset acceptance completion Xn4
b5 (Prohibited to use) Xn5
b6
Normal completion of data link startup by buffer
memory parameters
Xn6
b7
Abnormal completion of data link startup by buffer
memory parameters
Xn7
b8
Normal completion of data link startup by EEPROM
parameters
Xn8
b9
Abnormal completion of data link startup by
EEPROM parameters
Xn9
b10
Normal completion of parameter registration to
EEPROM
XnA
b11
Abnormal completion of parameter registration to
EEPROM
XnB
b12
(Prohibited to use)
XnC
b13 XnD
b14 XnE
b15 Module ready XnF
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-13
Table 4.9:
PLC Master block
Write (when TO instruction is used)
BFM
number
Write
bit
Output signal name
Reference: Output number
in A/QnA/Q Series
BFM
#AH
(#10)
b0 Refresh command Yn0
b1
(Prohibited to use)
Yn1
b2 Yn2
b3 Yn3
b4 Request for module reset Yn4
b5 (Prohibited to use) Yn5
b6
Request for data link startup by buffer memory
parameters
Yn6
b7 (Prohibited to use) Yn7
b8
Request for data link startup by EEPROM
parameters
Yn8
b9 (Prohibited to use) Yn9
b10 Request for parameter registration to EEPROM YnA
b11
(Prohibited to use)
YnB
b12 YnC
b13 YnD
b14 YnE
b15 YnF
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-14
.
Table 4.10:
PLC Master block
Read (when FROM instruction is used)
BFM
number
Read
bit
Signal name
Reference: Input number
in A/QnA/Q Series
BFM
#BH
(#11)
b0
(Prohibited to use)
X(n+1)0
b1 X(n+1)1
b2 X(n+1)2
b3 X(n+1)3
b4 X(n+1)4
b5 X(n+1)5
b6 X(n+1)6
b7 X(n+1)7
b8 X(n+1)8
b9 X(n+1)9
b10 X(n+1)A
b11 X(n+1)B
b12 X(n+1)C
b13 X(n+1)D
b14 X(n+1)E
b15 X(n+1)F
Table 4.11:
PLC Master block
Write (when TO instruction is used)
BFM
number
Write
bit
Signal name
Reference: Output number
in A/QnA/Q Series
BFM
#BH
(#11)
b0
(Prohibited to use)
Y(n+1)0
b1 Y(n+1)1
b2 Y(n+1)2
b3 Y(n+1)3
b4 Y(n+1)4
b5 Y(n+1)5
b6 Y(n+1)6
b7 Y(n+1)7
b8 Y(n+1)8
b9 Y(n+1)9
b10 Y(n+1)A
b11 Y(n+1)B
b12 Y(n+1)C
b13 Y(n+1)D
b14 Y(n+1)E
b15 Y(n+1)F
Important
The output signals prohibited in the table above are used by the system, thus cannot
be accessed by the user.
If used, normal operations cannot be guaranteed.
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-15
4.6.4 I/O signal details
This section describes the ON/OFF timing, the conditions, etc. of the I/O signals shown in
Section 4.6.3.
[Read signals]
1) Read module error: BFM#AH b0
Indicates whether the module is normal or not.
OFF: The module is normal.
ON : The module is abnormal.
2) Read data link status in host station: BFM#AH b1
Indicates the data link status in the host station.
OFF: Data link is stopped.
ON : Data link is in progress.
3) Read parameter setting status: BFM#AH b2
Indicates the parameter setting status in the host station.
The signal SB006D has the same meaning.
OFF: The setting is normal.
ON : There is an error in the setting. (The error code is stored in SW0068.)
This signal turns OFF when the write request for data link startup by buffer memory
parameters (BFM#AH b6) or the write request for data link startup by EEPROM parameters
(BFM#AH b8) in which no error has occurred.
4) Read data link status in other stations: BFM#AH b3
Indicates the data link status at other stations (remote stations).
The signal SB0080 has the same meaning.
OFF: All stations are normal.
ON : There is an error in some stations. (The error station status is stored in SW0080.)
Module error input
(BFM#AH b0)
Module ready input
(BFM#AH b15)
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-16
5) Read module reset acceptance completion: BFM#AH b4
Indicates the acceptance status of the request by the write request for module reset
(BFM#AH b4).
This signal cannot be reset when the read module error is given (when BFM#AH b0 is ON.).
a) When the write request for module reset (BFM#AH b4) is set to ON, the read module
ready (BFM#AH b15) turns OFF and the initialization processing is executed.
When the initialization processing is normally completed, the read module ready
(BFM#AH b15) turns ON.
When the read module reset acceptance completion (BFM#AH b4) turns ON, the write
request for module reset (BFM#AH b4) turns OFF.
b) When the write request for module reset (BFM#AH b4) is set to ON, the read module
ready (BFM#AH b15) turns OFF and the initialization processing is executed.
When the initialization processing is abnormally completed, the read module ready
(BFM#AH b15) does not turn ON, but the read module error (BFM#AH b0) turns ON
instead.
Read module reset acceptance
completion
(BFM#AH b4)
Read module ready
(BFM#AH b15)
[Normal startup after reset]
Write request for module reset
(BFM#AH b4)
Initialization
processing
Read module reset acceptance
completion
(BFM#AH b4)
Read module ready
(BFM#AH b15)
[Abnormal startup after reset]
Read module error
(BFM#AH b0)
Write request for module reset
(BFM#AH b4)
OFF
Initialization
processing
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-17
6) Read normal completion of data link startup by buffer memory parameters: BFM#AH b6
Indicates the normal completion status of the data link startup request by the write request
for data link startup by buffer memory parameters (BFM#AH b6).
a) When the write request for data link startup by buffer memory parameters (BFM#AH b6)
is set to ON, the contents of the buffer memory parameters are checked. When the
contents are normal, the system automatically starts data link.
b) When data link startup is normally completed, the read data link startup normal
completion (BFM#AH b6) turns ON.
c) When the write request for data link startup by buffer memory parameters (BFM#AH b6)
is set to OFF, the read normal completion of data link star tup by buffer memory
parameters (BFM#AH b6) turns OFF.
7) Read abnormal completion of data link startup by buffer memory parameters: BFM#AH b7
Indicates the abnormal completion status of the data link startup request by the write
request for data link startup by buffer memory parameters (BFM#AH b6).
a) When the write request for data link startup by buffer memory parameters (BFM#AH b6)
is set to ON, the contents of the buffer memory are checked. When the contents are
abnormal, the read abnormal completion of data link star tup by buffer memory
parameters (BFM#AH b7) turns ON.
b) The read parameter setting status (BFM#AH b2) turns ON, and the error code is stored
in the buffer memory for the parameter status in host station (SW0068).
c) When the write request for data link startup by buffer memory parameters (BFM#AH b6)
is set to OFF, the read abnormal completion of data link startup by buffer memory
parameters (BFM#AH b7) turns OFF.
Read normal completion of data link startup
by buffer memory parameters
(BFM#AH b6)
Read parameter setting status
(BFM#AH b2)
Parameter status in host station
(SW0068)
Write request for data link startup by buffer
memory parameters
(BFM#AH b6)
Startup
processing
OFF
0
Read abnormal completion of data link
startup by buffer memory parameters
(BFM#AH b7)
Read parameter setting status
(BFM#AH b2)
Parameter status in host station
(SW0068)
Write request for data link startup by buffer
memory parameters
(BFM#AH b6)
OFF
0 Error code
Startup
processing
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-18
8) Read normal completion of data link startup by EEPROM parameters: BFM#AH b8
Indicates the normal completion status of the data link startup request by the write request
for data link startup by EEPROM parameters (BFM#AH b8).
a) When the write request for data link startup by EEPROM parameters (BFM#AH b8) is set
to ON, the contents of the EEPROM parameters are checked. When the contents are
normal, the system automatically starts data link.
b) When data link startup is normally completed, the read normal completion of data link
startup by EEPROM parameters (BFM#AH b8) turns ON.
c) When the write request for data link startup by EEPROM parameters (BFM#AH b8) is set
to OFF, the read normal completion of data link startup by EEPROM parameters
(BFM#AH b8) turns OFF.
9) Read abnormal completion of data link startup by EEPROM parameters: BFM#AH b9
Indicates the abnormal completion status of the data link startup request by the write
request for data link startup by EEPROM parameters (BFM#AH b8).
a) When the write request for data link startup by EEPROM parameters (BFM#AH b8) is set
to ON, the contents of the EEPROM parameters are checked. When the contents are
abnormal, the read abnormal completion of data link startup by EEPROM parameters
(BFM#AH b9) turns ON.
b) The read parameter setting status (BFM#AH b2) turns ON, the error code is stored in the
buffer memory for the parameter status in host station (SW0068).
c) When the write request for data link startup by EEPROM parameters (BFM#AH b8) is set
to OFF, the read abnormal completion of data link startup by EEPROM parameters
(BFM#AH b9) turns OFF.
Read normal completion of data link startup
by EEPROM parameters
(BFM#AH b8)
Read parameter setting status
(BFM#AH b2)
Parameter status in host station
(SW0068)
Write request for data link startup by
EEPROM parameters
(BFM#AH b8)
OFF
0
Startup
processing
Read abnormal completion of data link
startup by EEPROM parameters
(BFM#AH b9)
Read parameter setting status
(BFM#AH b2)
Parameter status in host station
(SW0068)
Write request for data link startup by
EEPROM parameters
(BFM#AH b8)
OFF
0 Error code
Startup
processing
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-19
10)Read normal completion of parameter registration to EEPROM: BFM#AH b10
Indicates the normal completion status of the parameter (buffer memory address)
registration to the EEPROM by the write request for parameter registration to EEPROM
(BFM#AH b10).
a) When the write request for parameter registration to EEPROM (BFM#AH b10) is set to
ON, the parameters stored in the buffer memory for the parameter information area are
registered to the EEPROM.
b) When registration is normally completed, the read normal completion of parameter
registration to EEPROM (BFM#AH b10) turns ON.
c) When the write request for parameter registration to EEPROM (BFM#AH b10) is set to
OFF, the read normal completion of parameter registration to EEPROM (BFM#AH b10)
turns OFF.
11)Read abnormal completion of parameter registration to EEPROM: BFM#AH b11
Indicates the abnormal completion status of the parameter (buffer memory address) regis-
tration to the EEPROM by the write request for parameter registration to EEPROM
(BFM#AH b10).
a) When the write request for parameter registration to EEPROM (BFM#AH b10) is set to
ON, the parameters stored in the buffer memory for the parameter information area are
registered to the EEPROM.
b) When registration is abnormally completed, the write abnormal completion of parameter
registration to EEPROM (BFM#AH b11) turns ON, and the error code is stored in the
buffer memory for the EEPROM registration status (SW00B9).
c) When the write request for parameter registration to EEPROM (BFM#AH b10) is set to
OFF, the read abnormal completion of parameter registration to EEPROM (BFM#AH
b11) turns OFF.
Read normal completion of parameter
registration to EEPROM
(BFM#AH b10)
EEPROM registration status
(SW00B9)
Registration
processing
Write request for parameter registration to
EEPROM
(BFM#AH b10)
0
Read abnormal completion of parameter
registration to EEPROM
(BFM#AH b11)
EEPROM registration status
(SW00B9)
Write request for parameter registration to
EEPROM
(BFM#AH b10)
0 Error code
Registration
processing
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-20
12)Read module ready: BFM#AH b15
Indicates whether or not the module is ready for operation.
a) The signal automatically turns ON when the module becomes ready for operation.
b) The signal turns OFF when one of the following conditions occur:
1) There is an error in the module switch settings.
2) The output signal of request for module reset (BFM#AH b4) turns ON.
3) The input signal of module error (BFM#AH b0) turns ON.
[Write signals]
13)Write refresh command: BFM#AH b0
Indicates whether or not the contents of the buffer memory for "remote output RY
(addresses 160H to 17FH)" are effective.
OFF: Not effective (Sends all OFF data.)
ON : Effective (Sends the data in "remote output (addresses 160H to 17DH)" in the
buffer memory.)
Points
1) Set to ON the write refresh command (BFM#AH b0) before starting up the data
link.
2) When the PLC CPU is in the stop status, the write refresh command (BFM#AH
b0) turns OFF.
Read module ready
(BFM#AH b15)
Read module error
(BFM#AH b0)
Write request for module reset
(BFM#AH b4)
Power ON
Remote input (RX)
Remote output (RY)
Master station Remote I/O station
Input
Remote input (RX)
Output
Remote output (RY)
Remote device station
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-21
14)Write request for module reset: BFM#AH b4
Resets the module.
The module can be reset individually without resetting the PLC.
For the signal timing, refer to 5).
15)Write request for data link startup by buffer memory parameters: BFM#AH b6
Starts up the data link in accordance with the contents of the parameters in the buffer
memory.
For the signal timing, refer to 6) and 7).
16)Write request for data link startup by EEPROM parameters: BFM#AH b8
Starts up the data link in accordance with the contents of the parameters registered in the
EEPROM.
For the signal timing, refer to 8) and 9).
17)Write request for parameter registration to EEPROM: BFM#AH b10
Registers the parameters stored in the buffer memory to the EEPROM.
For the signal timing, refer to 10) and 11).
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-22
4.6.5 Master block control signals
1) FROM/TO instruction access error judgement time: BFM#1CH
This buffer memory sets the period of time to judge FROM/TO instruction access errors in
the unit of 10 ms.
The default value is 200 ms (K20).
For example, when you would like to set the judgement time to 10 ms, write "1" using the TO
instruction.
If the access time for read/write by the FROM/TO instruction from the PLC to the buffer
memory (excluding the buffer memory prohibited to use) in the FX2N-16CCL-M exceeds the
period of time set here, the system regards it as an access error.
<Setting range>
1 to 32,767
<Point>
Make sure to set a value larger than one scan time to the FROM/TO instruction access
error judgement time.
If the preset value is shorter than one scan time, an access time error may occur in some
programs.
You can check the maximum scan time of the PLC by referring to D8012 (unit: 0.1 ms).
2) Detection of accesses outside allowable range: BFM#1DH
"1" is written here if there is a setting beyond the allowable specification range in the CC-
Link master for the FX Series.
When I/O operations and data link are not normally executed, you can check this buffer
memory to know whether or not an error has occurred.
3) Model code: BFM#1EH
The model code "K7510" specific to the FX2N-16CCL-M is written.
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-23
4.6.6 Remote input (RX)
- The input (RX) status from remote I/O stations and remote device stations is stored.
- Each station uses 2 words.
Master station
Remote I/O station
(Station No. 1: Occupies 1 station.)
RX F ~ RX 0
RX 1F ~ RX 10
RX 2F ~ RX 20
RX 3F ~ RX 30
RX 4F ~ RX 40
RX 5F ~ RX 50
RX 6F ~ RX 60
RX 7F ~ RX 70
RX 8F ~ RX 80
RX 9F ~ RX 90
RX AF ~ RX A0
RX BF ~ RX B0
RX CF ~ RX C0
RX DF ~ RX D0
RX EF ~ RX E0
RX FD ~ RX F0
RX10F ~ RX100
RX11F ~ RX110
RX1CF ~ RX1C1
RX1DF ~ RX1D0
~
Remote input (RX)
E0H
E1H
E2H
E3H
E4H
E5H
E6H
E7H
E8H
E9H
EAH
EBH
ECH
EDH
EEH
EFH
F0H
F2H
FDH
FBH
FCH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
For station
No. 6
For station
No. 7
For station
No. 8
For station
No. 9
For station
No. 15
X0F ~ X00
X1F ~ X10
RX0F ~ RX00
RX1F ~ RX10
Remote device station
(Station No. 2: Occupies 2 stations.)
F1H
Address
Remote input (RX)
~
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-24
[Correspondence among buffer memory number in master station, station number and remote input (RX)]
S
t
a
t
i
o
n

n
u
m
b
e
r
B
F
M

n
u
m
b
e
r
b
1
5
b
1
4
b
1
3
b
1
2
b
1
1
b
1
0
b
9
b
8
b
7
b
6
b
5
b
4
b
3
b
2
b
1
b
0
1
E
0
H
R
X

F
R
X

E
R
X

D
R
X

C
R
X

B
R
X

A
R
X

9
R
X

8
R
X

7
R
X

6
R
X

5
R
X

4
R
X

3
R
X

2
R
X

1
R
X

0
E
1
H
R
X

1
F
R
X

1
E
R
X

1
D
R
X

1
C
R
X

1
B
R
X

1
A
R
X

1
9
R
X

1
8
R
X

1
7
R
X

1
6
R
X

1
5
R
X

1
4
R
X

1
3
R
X

1
2
R
X

1
1
R
X

1
0
2
E
2
H
R
X

2
F
R
X

2
E
R
X

2
D
R
X

2
C
R
X

2
B
R
X

2
A
R
X

2
9
R
X

2
8
R
X

2
7
R
X

2
6
R
X

2
5
R
X

2
4
R
X

2
3
R
X

2
2
R
X

2
1
R
X

2
0
E
3
H
R
X

3
F
R
X

3
E
R
X

3
D
R
X

3
C
R
X

3
B
R
X

3
A
R
X

3
9
R
X

3
8
R
X

3
7
R
X

3
6
R
X

3
5
R
X

3
4
R
X

3
3
R
X

3
2
R
X

3
1
R
X

3
0
3
E
4
H
R
X

4
F
R
X

4
E
R
X

4
D
R
X

4
C
R
X

4
B
R
X

4
A
R
X

4
9
R
X

4
8
R
X

4
7
R
X

4
6
R
X

4
5
R
X

4
4
R
X

4
3
R
X

4
2
R
X

4
1
R
X

4
0
E
5
H
R
X

5
F
R
X

5
E
R
X

5
D
R
X

5
C
R
X

5
B
R
X

5
A
R
X

5
9
R
X

5
8
R
X

5
7
R
X

5
6
R
X

5
5
R
X

5
4
R
X

5
3
R
X

5
2
R
X

5
1
R
X

5
0
4
E
6
H
R
X

6
F
R
X

6
E
R
X

6
D
R
X

6
C
R
X

6
B
R
X

6
A
R
X

6
9
R
X

6
8
R
X

6
7
R
X

6
6
R
X

6
5
R
X

6
4
R
X

6
3
R
X

6
2
R
X

6
1
R
X

6
0
E
7
H
R
X

7
F
R
X

7
E
R
X

7
D
R
X

7
C
R
X

7
B
R
X

7
A
R
X

7
9
R
X

7
8
R
X

7
7
R
X

7
6
R
X

7
5
R
X

7
4
R
X

7
3
R
X

7
2
R
X

7
1
R
X

7
0
5
E
8
H
R
X

8
F
R
X

8
E
R
X

8
D
R
X

8
C
R
X

8
B
R
X

8
A
R
X

8
9
R
X

8
8
R
X

8
7
R
X

8
6
R
X

8
5
R
X

8
4
R
X

8
3
R
X

8
2
R
X

8
1
R
X

8
0
E
9
H
R
X

9
F
R
X

9
E
R
X

9
D
R
X

9
C
R
X

9
B
R
X

9
A
R
X

9
9
R
X

9
8
R
X

9
7
R
X

9
6
R
X

9
5
R
X

9
4
R
X

9
3
R
X

9
2
R
X

9
1
R
X

9
0
6
E
A
H
R
X

A
F
R
X

A
E
R
X

A
D
R
X

A
C
R
X

A
B
R
X

A
A
R
X

A
9
R
X

A
8
R
X

A
7
R
X

A
6
R
X

A
5
R
X

A
4
R
X

A
3
R
X

A
2
R
X

A
1
R
X

A
0
E
B
H
R
X

B
F
R
X

B
E
R
X

B
D
R
X

B
C
R
X

B
B
R
X

B
A
R
X

B
9
R
X

B
8
R
X

B
7
R
X

B
6
R
X

B
5
R
X

B
4
R
X

B
3
R
X

B
2
R
X

B
1
R
X

B
0
7
E
C
H
R
X

C
F
R
X

C
E
R
X

C
D
R
X

C
C
R
X

C
B
R
X

C
A
R
X

C
9
R
X

C
8
R
X

C
7
R
X

C
6
R
X

C
5
R
X

C
4
R
X

C
3
R
X

C
2
R
X

C
1
R
X

C
0
E
D
H
R
X

D
F
R
X

D
E
R
X

D
D
R
X

D
C
R
X

D
B
R
X

D
A
R
X

D
9
R
X

D
8
R
X

D
7
R
X

D
6
R
X

D
5
R
X

D
4
R
X

D
3
R
X

D
2
R
X

D
1
R
X

D
0
8
E
E
H
R
X

E
F
R
X

E
E
R
X

E
D
R
X

E
C
R
X

E
B
R
X

E
A
R
X

E
9
R
X

E
8
R
X

E
7
R
X

E
6
R
X

E
5
R
X

E
4
R
X

E
3
R
X

E
2
R
X

E
1
R
X

E
0
E
F
H
R
X

F
F
R
X

F
E
R
X

F
D
R
X

F
C
R
X

F
B
R
X

F
A
R
X

F
9
R
X

F
8
R
X

F
7
R
X

F
6
R
X

F
5
R
X

F
4
R
X

F
3
R
X

F
2
R
X

F
1
R
X

F
0
9
F
0
H
R
X

1
0
F
R
X

1
0
E
R
X

1
0
D
R
X

1
0
C
R
X

1
0
B
R
X

1
0
A
R
X

1
0
9
R
X

1
0
8
R
X

1
0
7
R
X

1
0
6
R
X

1
0
5
R
X

1
0
4
R
X

1
0
3
R
X

1
0
2
R
X

1
0
1
R
X

1
0
0
F
1
H
R
X

1
1
F
R
X

1
1
E
R
X

1
1
D
R
X

1
1
C
R
X

1
1
B
R
X

1
1
A
R
X

1
1
9
R
X

1
1
8
R
X

1
1
7
R
X

1
1
6
R
X

1
1
5
R
X

1
1
4
R
X

1
1
3
R
X

1
1
2
R
X

1
1
1
R
X

1
1
0
1
0
F
2
H
R
X

1
2
F
R
X

1
2
E
R
X

1
2
D
R
X

1
2
C
R
X

1
2
B
R
X

1
2
A
R
X

1
2
9
R
X

1
2
8
R
X

1
2
7
R
X

1
2
6
R
X

1
2
5
R
X

1
2
4
R
X

1
2
3
R
X

1
2
2
R
X

1
2
1
R
X

1
2
0
F
3
H
R
X

1
3
F
R
X

1
3
E
R
X

1
3
D
R
X

1
3
C
R
X

1
3
B
R
X

1
3
A
R
X

1
3
9
R
X

1
3
8
R
X

1
3
7
R
X

1
3
6
R
X

1
3
5
R
X

1
3
4
R
X

1
3
3
R
X

1
3
2
R
X

1
3
1
R
X

1
3
0
1
1
F
4
H
R
X

1
4
F
R
X

1
4
E
R
X

1
4
D
R
X

1
4
C
R
X

1
4
B
R
X

1
4
A
R
X

1
4
9
R
X

1
4
8
R
X

1
4
7
R
X

1
4
6
R
X

1
4
5
R
X

1
4
4
R
X

1
4
3
R
X

1
4
2
R
X

1
4
1
R
X

1
4
0
F
5
H
R
X

1
5
F
R
X

1
5
E
R
X

1
5
D
R
X

1
5
C
R
X

1
5
B
R
X

1
5
A
R
X

1
5
9
R
X

1
5
8
R
X

1
5
7
R
X

1
5
6
R
X

1
5
5
R
X

1
5
4
R
X

1
5
3
R
X

1
5
2
R
X

1
5
1
R
X

1
5
0
1
2
F
6
H
R
X

1
6
F
R
X

1
6
E
R
X

1
6
D
R
X

1
6
C
R
X

1
6
B
R
X

1
6
A
R
X

1
6
9
R
X

1
6
8
R
X

1
6
7
R
X

1
6
6
R
X

1
6
5
R
X

1
6
4
R
X

1
6
3
R
X

1
6
2
R
X

1
6
1
R
X

1
6
0
F
7
H
R
X

1
7
F
R
X

1
7
E
R
X

1
7
D
R
X

1
7
C
R
X

1
7
B
R
X

1
7
A
R
X

1
7
9
R
X

1
7
8
R
X

1
7
7
R
X

1
7
6
R
X

1
7
5
R
X

1
7
4
R
X

1
7
3
R
X

1
7
2
R
X

1
7
1
R
X

1
7
0
1
3
F
8
H
R
X

1
8
F
R
X

1
8
E
R
X

1
8
D
R
X

1
8
C
R
X

1
8
B
R
X

1
8
A
R
X

1
8
9
R
X

1
8
8
R
X

1
8
7
R
X

1
8
6
R
X

1
8
5
R
X

1
8
4
R
X

1
8
3
R
X

1
8
2
R
X

1
8
1
R
X

1
8
0
F
9
H
R
X

1
9
F
R
X

1
9
E
R
X

1
9
D
R
X

1
9
C
R
X

1
9
B
R
X

1
9
A
R
X

1
9
9
R
X

1
9
8
R
X

1
9
7
R
X

1
9
6
R
X

1
9
5
R
X

1
9
4
R
X

1
9
3
R
X

1
9
2
R
X

1
9
1
R
X

1
9
0
1
4
F
A
H
R
X

1
A
F
R
X

1
A
E
R
X

1
A
D
R
X

1
A
C
R
X

1
A
B
R
X

1
A
A
R
X

1
A
9
R
X

1
A
8
R
X

1
A
7
R
X

1
A
6
R
X

1
A
5
R
X

1
A
4
R
X

1
A
3
R
X

1
A
2
R
X

1
A
1
R
X

1
A
0
F
B
H
R
X

1
B
F
R
X

1
B
E
R
X

1
B
D
R
X

1
B
C
R
X

1
B
B
R
X

1
B
A
R
X

1
B
9
R
X

1
B
8
R
X

1
B
7
R
X

1
B
6
R
X

1
B
5
R
X

1
B
4
R
X

1
B
3
R
X

1
B
2
R
X

1
B
1
R
X

1
B
0
1
5
F
C
H
R
X

1
C
F
R
X

1
C
E
R
X

1
C
D
R
X

1
C
C
R
X

1
C
B
R
X

1
C
A
R
X

1
C
9
R
X

1
C
8
R
X

1
C
7
R
X

1
C
6
R
X

1
C
5
R
X

1
C
4
R
X

1
C
3
R
X

1
C
2
R
X

1
C
1
R
X

1
C
0
F
D
H
R
X

1
D
F
R
X

1
D
E
R
X

1
D
D
R
X

1
D
C
R
X

1
D
B
R
X

1
D
A
R
X

1
D
9
R
X

1
D
8
R
X

1
D
7
R
X

1
D
6
R
X

1
D
5
R
X

1
D
4
R
X

1
D
3
R
X

1
D
2
R
X

1
D
1
R
X

1
D
0
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-25
4.6.7 Remote output (RY)
- The output (RY) status to remote I/O stations and remote device stations is stored as
below.
- Each station uses 2 words.
Master station
Remote I/O station
(Station No. 1: Occupies 1 station.)
RY F ~ RY 0
RY 1F ~ RY 10
RY 2F ~ RY 20
RY 3F ~ RY 30
RY 4F ~ RY 40
RY 5F ~ RY 50
RY 6F ~ RY 60
RY 7F ~ RY 70
RY 8F ~ RY 80
RY 9F ~ RY 90
RY AF ~ RY A0
RY BF ~ RY B0
RY CF ~ RY C0
RY DF ~ RY D0
RY EF ~ RY E0
RY FD ~ RY F0
RY10F ~ RY100
RY11F ~ RY110
RY1CF ~ RY1C0
RY1DF ~ RY1D0
~
Remote output (RY)
160H
161H
162H
163H
164H
165H
166H
167H
168H
169H
16AH
16BH
16CH
16DH
16EH
16FH
170H
172H
17DH
17BH
17CH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
For station
No. 6
For station
No. 7
For station
No. 8
For station
No. 9
For station
No. 15
Y0F ~ Y00
Y1F ~ Y10
RY0F ~ RY00
RY1F ~ RY10
Remote device station
(Station No. 2: Occupies 2 stations.)
171H
Address
~
Remote output (RY)
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-26
[Correspondence among buffer memory number in master station, station number and remote output (RY) number]
S
t
a
t
i
o
n

n
u
m
b
e
r
B
F
M

n
u
m
b
e
r
b
1
5
b
1
4
b
1
3
b
1
2
b
1
1
b
1
0
b
9
b
8
b
7
b
6
b
5
b
4
b
3
b
2
b
1
b
0
1
1
6
0
H
R
Y

F
R
Y

E
R
Y

D
R
Y

C
R
Y

B
R
Y

A
R
Y

9
R
Y

8
R
Y

7
R
Y

6
R
Y

5
R
Y

4
R
Y

3
R
Y

2
R
Y

1
R
Y

0
1
6
1
H
R
Y

1
F
R
Y

1
E
R
Y

1
D
R
Y

1
C
R
Y

1
B
R
Y

1
A
R
Y

1
9
R
Y

1
8
R
Y

1
7
R
Y

1
6
R
Y

1
5
R
Y

1
4
R
Y

1
3
R
Y

1
2
R
Y

1
1
R
Y

1
0
2
1
6
2
H
R
Y

2
F
R
Y

2
E
R
Y

2
D
R
Y

2
C
R
Y

2
B
R
Y

2
A
R
Y

2
9
R
Y

2
8
R
Y

2
7
R
Y

2
6
R
Y

2
5
R
Y

2
4
R
Y

2
3
R
Y

2
2
R
Y

2
1
R
Y

2
0
1
6
3
H
R
Y

3
F
R
Y

3
E
R
Y

3
D
R
Y

3
C
R
Y

3
B
R
Y

3
A
R
Y

3
9
R
Y

3
8
R
Y

3
7
R
Y

3
6
R
Y

3
5
R
Y

3
4
R
Y

3
3
R
Y

3
2
R
Y

3
1
R
Y

3
0
3
1
6
4
H
R
Y

4
F
R
Y

4
E
R
Y

4
D
R
Y

4
C
R
Y

4
B
R
Y

4
A
R
Y

4
9
R
Y

4
8
R
Y

4
7
R
Y

4
6
R
Y

4
5
R
Y

4
4
R
Y

4
3
R
Y

4
2
R
Y

4
1
R
Y

4
0
1
6
5
H
R
Y

5
F
R
Y

5
E
R
Y

5
D
R
Y

5
C
R
Y

5
B
R
Y

5
A
R
Y

5
9
R
Y

5
8
R
Y

5
7
R
Y

5
6
R
Y

5
5
R
Y

5
4
R
Y

5
3
R
Y

5
2
R
Y

5
1
R
Y

5
0
4
1
6
6
H
R
Y

6
F
R
Y

6
E
R
Y

6
D
R
Y

6
C
R
Y

6
B
R
Y

6
A
R
Y

6
9
R
Y

6
8
R
Y

6
7
R
Y

6
6
R
Y

6
5
R
Y

6
4
R
Y

6
3
R
Y

6
2
R
Y

6
1
R
Y

6
0
1
6
7
H
R
Y

7
F
R
Y

7
E
R
Y

7
D
R
Y

7
C
R
Y

7
B
R
Y

7
A
R
Y

7
9
R
Y

7
8
R
Y

7
7
R
Y

7
6
R
Y

7
5
R
Y

7
4
R
Y

7
3
R
Y

7
2
R
Y

7
1
R
Y

7
0
5
1
6
8
H
R
Y

8
F
R
Y

8
E
R
Y

8
D
R
Y

8
C
R
Y

8
B
R
Y

8
A
R
Y

8
9
R
Y

8
8
R
Y

8
7
R
Y

8
6
R
Y

8
5
R
Y

8
4
R
Y

8
3
R
Y

8
2
R
Y

8
1
R
Y

8
0
1
6
9
H
R
Y

9
F
R
Y

9
E
R
Y

9
D
R
Y

9
C
R
Y

9
B
R
Y

9
A
R
Y

9
9
R
Y

9
8
R
Y

9
7
R
Y

9
6
R
Y

9
5
R
Y

9
4
R
Y

9
3
R
Y

9
2
R
Y

9
1
R
Y

9
0
6
1
6
A
H
R
Y

A
F
R
Y

A
E
R
Y

A
D
R
Y

A
C
R
Y

A
B
R
Y

A
A
R
Y

A
9
R
Y

A
8
R
Y

A
7
R
Y

A
6
R
Y

A
5
R
Y

A
4
R
Y

A
3
R
Y

A
2
R
Y

A
1
R
Y

A
0
1
6
B
H
R
Y

B
F
R
Y

B
E
R
Y

B
D
R
Y

B
C
R
Y

B
B
R
Y

B
A
R
Y

B
9
R
Y

B
8
R
Y

B
7
R
Y

B
6
R
Y

B
5
R
Y

B
4
R
Y

B
3
R
Y

B
2
R
Y

B
1
R
Y

B
0
7
1
6
C
H
R
Y

C
F
R
Y

C
E
R
Y

C
D
R
Y

C
C
R
Y

C
B
R
Y

C
A
R
Y

C
9
R
Y

C
8
R
Y

C
7
R
Y

C
6
R
Y

C
5
R
Y

C
4
R
Y

C
3
R
Y

C
2
R
Y

C
1
R
Y

C
0
1
6
D
H
R
Y

D
F
R
Y

D
E
R
Y

D
D
R
Y

D
C
R
Y

D
B
R
Y

D
A
R
Y

D
9
R
Y

D
8
R
Y

D
7
R
Y

D
6
R
Y

D
5
R
Y

D
4
R
Y

D
3
R
Y

D
2
R
Y

D
1
R
Y

D
0
8
1
6
E
H
R
Y

E
F
R
Y

E
E
R
Y

E
D
R
Y

E
C
R
Y

E
B
R
Y

E
A
R
Y

E
9
R
Y

E
8
R
Y

E
7
R
Y

E
6
R
Y

E
5
R
Y

E
4
R
Y

E
3
R
Y

E
2
R
Y

E
1
R
Y

E
0
1
6
F
H
R
Y

F
F
R
Y

F
E
R
Y

F
D
R
Y

F
C
R
Y

F
B
R
Y

F
A
R
Y

F
9
R
Y

F
8
R
Y

F
7
R
Y

F
6
R
Y

F
5
R
Y

F
4
R
Y

F
3
R
Y

F
2
R
Y

F
1
R
Y

F
0
9
1
7
0
H
R
Y

1
0
F
R
Y

1
0
E
R
Y

1
0
D
R
Y

1
0
C
R
Y

1
0
B
R
Y

1
0
A
R
Y

1
0
9
R
Y

1
0
8
R
Y

1
0
7
R
Y

1
0
6
R
Y

1
0
5
R
Y

1
0
4
R
Y

1
0
3
R
Y

1
0
2
R
Y

1
0
1
R
Y

1
0
0
1
7
1
H
R
Y

1
1
F
R
Y

1
1
E
R
Y

1
1
D
R
Y

1
1
C
R
Y

1
1
B
R
Y

1
1
A
R
Y

1
1
9
R
Y

1
1
8
R
Y

1
1
7
R
Y

1
1
6
R
Y

1
1
5
R
Y

1
1
4
R
Y

1
1
3
R
Y

1
1
2
R
Y

1
1
1
R
Y

1
1
0
1
0
1
7
2
H
R
Y

1
2
F
R
Y

1
2
E
R
Y

1
2
D
R
Y

1
2
C
R
Y

1
2
B
R
Y

1
2
A
R
Y

1
2
9
R
Y

1
2
8
R
Y

1
2
7
R
Y

1
2
6
R
Y

1
2
5
R
Y

1
2
4
R
Y

1
2
3
R
Y

1
2
2
R
Y

1
2
1
R
Y

1
2
0
1
7
3
H
R
Y

1
3
F
R
Y

1
3
E
R
Y

1
3
D
R
Y

1
3
C
R
Y

1
3
B
R
Y

1
3
A
R
Y

1
3
9
R
Y

1
3
8
R
Y

1
3
7
R
Y

1
3
6
R
Y

1
3
5
R
Y

1
3
4
R
Y

1
3
3
R
Y

1
3
2
R
Y

1
3
1
R
Y

1
3
0
1
1
1
7
4
H
R
Y

1
4
F
R
Y

1
4
E
R
Y

1
4
D
R
Y

1
4
C
R
Y

1
4
B
R
Y

1
4
A
R
Y

1
4
9
R
Y

1
4
8
R
Y

1
4
7
R
Y

1
4
6
R
Y

1
4
5
R
Y

1
4
4
R
Y

1
4
3
R
Y

1
4
2
R
Y

1
4
1
R
Y

1
4
0
1
7
5
H
R
Y

1
5
F
R
Y

1
5
E
R
Y

1
5
D
R
Y

1
5
C
R
Y

1
5
B
R
Y

1
5
A
R
Y

1
5
9
R
Y

1
5
8
R
Y

1
5
7
R
Y

1
5
6
R
Y

1
5
5
R
Y

1
5
4
R
Y

1
5
3
R
Y

1
5
2
R
Y

1
5
1
R
Y

1
5
0
1
2
1
7
6
H
R
Y

1
6
F
R
Y

1
6
E
R
Y

1
6
D
R
Y

1
6
C
R
Y

1
6
B
R
Y

1
6
A
R
Y

1
6
9
R
Y

1
6
8
R
Y

1
6
7
R
Y

1
6
6
R
Y

1
6
5
R
Y

1
6
4
R
Y

1
6
3
R
Y

1
6
2
R
Y

1
6
1
R
Y

1
6
0
1
7
7
H
R
Y

1
7
F
R
Y

1
7
E
R
Y

1
7
D
R
Y

1
7
C
R
Y

1
7
B
R
Y

1
7
A
R
Y

1
7
9
R
Y

1
7
8
R
Y

1
7
7
R
Y

1
7
6
R
Y

1
7
5
R
Y

1
7
4
R
Y

1
7
3
R
Y

1
7
2
R
Y

1
7
1
R
Y

1
7
0
1
3
1
7
8
H
R
Y

1
8
F
R
Y

1
8
E
R
Y

1
8
D
R
Y

1
8
C
R
Y

1
8
B
R
Y

1
8
A
R
Y

1
8
9
R
Y

1
8
8
R
Y

1
8
7
R
Y

1
8
6
R
Y

1
8
5
R
Y

1
8
4
R
Y

1
8
3
R
Y

1
8
2
R
Y

1
8
1
R
Y

1
8
0
1
7
9
H
R
Y

1
9
F
R
Y

1
9
E
R
Y

1
9
D
R
Y

1
9
C
R
Y

1
9
B
R
Y

1
9
A
R
Y

1
9
9
R
Y

1
9
8
R
Y

1
9
7
R
Y

1
9
6
R
Y

1
9
5
R
Y

1
9
4
R
Y

1
9
3
R
Y

1
9
2
R
Y

1
9
1
R
Y

1
9
0
1
4
1
7
A
H
R
Y

1
A
F
R
Y

1
A
E
R
Y

1
A
D
R
Y

1
A
C
R
Y

1
A
B
R
Y

1
A
A
R
Y

1
A
9
R
Y

1
A
8
R
Y

1
A
7
R
Y

1
A
6
R
Y

1
A
5
R
Y

1
A
4
R
Y

1
A
3
R
Y

1
A
2
R
Y

1
A
1
R
Y

1
A
0
1
7
B
H
R
Y

1
B
F
R
Y

1
B
E
R
Y

1
B
D
R
Y

1
B
C
R
Y

1
B
B
R
Y

1
B
A
R
Y

1
B
9
R
Y

1
B
8
R
Y

1
B
7
R
Y

1
B
6
R
Y

1
B
5
R
Y

1
B
4
R
Y

1
B
3
R
Y

1
B
2
R
Y

1
B
1
R
Y

1
B
0
1
5
1
7
C
H
R
Y

1
C
F
R
Y

1
C
E
R
Y

1
C
D
R
Y

1
C
C
R
Y

1
C
B
R
Y

1
C
A
R
Y

1
C
9
R
Y

1
C
8
R
Y

1
C
7
R
Y

1
C
6
R
Y

1
C
5
R
Y

1
C
4
R
Y

1
C
3
R
Y

1
C
2
R
Y

1
C
1
R
Y

1
C
0
1
7
D
H
R
Y

1
D
F
R
Y

1
D
E
R
Y

1
D
D
R
Y

1
D
C
R
Y

1
D
B
R
Y

1
D
A
R
Y

1
D
9
R
Y

1
D
8
R
Y

1
D
7
R
Y

1
D
6
R
Y

1
D
5
R
Y

1
D
4
R
Y

1
D
3
R
Y

1
D
2
R
Y

1
D
1
R
Y

1
D
0
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-27
4.6.8 Remote register (RWw) Master station --> Remote device station
- The data transmitted to the remote register (RWw) in remote device stations is stored as
below.
- Each station uses 4 words.
Master station
Remote I/O station
(Station No. 1: Occupies 1 station.)
RWw 0
~
Remote register
(RWw)
1E0H
1E1H
1E2H
1E3H
1E4H
1E5H
1E6H
1E7H
1E8H
1E9H
1EAH
1EBH
1ECH
1EDH
1EEH
1EFH
1F0H
1F1H
219H
21AH
217H
218H
21BH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
For station
No. 6
For station
No. 7
For station
No. 8
For station
No. 15
Remote device station
(Station No. 2: Occupies 2 stations.)
RWw 1
RWw 2
RWw 3
RWw 4
RWw 5
RWw 6
RWw 7
RWw 8
RWw 9
RWw A
RWw B
RWw C
RWw D
RWw E
RWw F
RWw 10
RWw 11
RWw 38
RWw 39
RWw 3A
RWw 3B
RWw 12
RWw 13
RWw 14
RWw 15
RWw 16
RWw 17
RWw 18
RWw 19
RWw 1A
RWw 1B
RWw 1C
RWw 1D
RWw 1E
RWw 1F
1F3H
1F4H
1F5H
1F6H
1F7H
1F8H
1FAH
1FBH
1FCH
1FDH
1FEH
1FFH
1F2H
1F9H
200H
RWw 0
RWw 1
RWw 2
RWw 3
RWw 4
RWw 5
RWw 6
RWw 7
Address
Remote register (RWw)
~
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-28
[Correspondence among buffer memory number in master station, station number and remote register
(RWw) number]
Station
number
BFM
number
Remote register
number
Station
number
BFM
number
Remote register
number
1
1E0H RWw 0
9
200H RWw 20
1E1H RWw 1 201H RWw 21
1E2H RWw 2 202H RWw 22
1E3H RWw 3 203H RWw 23
2
1E4H RWw 4
10
204H RWw 24
1E5H RWw 5 205H RWw 25
1E6H RWw 6 206H RWw 26
1E7H RWw 7 207H RWw 27
3
1E8H RWw 8
11
208H RWw 28
1E9H RWw 9 209H RWw 29
1EAH RWw A 20AH RWw 2A
1EBH RWw B 20BH RWw 2B
4
1ECH RWw C
12
20CH RWw 2C
1EDH RWw D 20DH RWw 2D
1EEH RWw E 20EH RWw 2E
1EFH RWw F 20FH RWw 2F
5
1F0H RWw 10
13
210H RWw 30
1F1H RWw 11 211H RWw 31
1F2H RWw 12 212H RWw 32
1F3H RWw 13 213H RWw 33
6
1F4H RWw 14
14
214H RWw 34
1F5H RWw 15 215H RWw 35
1F6H RWw 16 216H RWw 36
1F7H RWw 17 217H RWw 37
7
1F8H RWw 18
15
218H RWw 38
1F9H RWw 19 219H RWw 39
1FAH RWw 1A 21AH RWw 3A
1FBH RWw 1B 21BH RWw 3B
8
1FCH RWw 1C
1FDH RWw 1D
1FEH RWw 1E
1FFH RWw 1F
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-29
4.6.9 Remote register (RWr) Master station <-- Remote device station
- The data transmitted from the remote register (RWr) in remote device stations is stored
as below.
- Each station uses 4 words.
Master station
Remote I/O station
(Station No. 1: Occupies 1 station.)
RWr 0
~
Remote register (RWr)
2E0H
2E1H
2E2H
2E3H
2E4H
2E5H
2E6H
2E7H
2E8H
2E9H
2EAH
2EBH
2ECH
2EDH
2EEH
2EFH
2F0H
2F1H
319H
31AH
317H
318H
31BH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
For station
No. 6
For station
No. 7
For station
No. 8
For station
No. 15
Remote device station
(Station No. 2: Occupies 2 stations.)
RWr 1
RWr 2
RWr 3
RWr 4
RWr 5
RWr 6
RWr 7
RWr 8
RWr 9
RWr A
RWr B
RWr C
RWr D
RWr E
RWr F
RWr 10
RWr 11
RWr 38
RWr 39
RWr 3A
RWr 3B
RWr 12
RWr 13
RWr 14
RWr 15
RWr 16
RWr 17
RWr 18
RWr 19
RWr 1A
RWr 1B
RWr 1C
RWr 1D
RWr 1E
RWr 1F
2F3H
2F4H
2F5H
2F6H
2F7H
2F8H
2FAH
2FBH
2FCH
2FDH
2FEH
2FFH
2F2H
2F9H
300H
RWr 0
RWr 1
RWr 2
RWr 3
RWr 4
RWr 5
RWr 6
RWr 7
Address
Remote register (RWr)
~
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-30
[Correspondence among buffer memory number in master station, station number and remote register
(RWr) number]
Station
number
BFM
number
Remote register
number
Station
number
BFM
number
Remote register
number
1
2E0H RWr 0
9
300H RWr 20
2E1H RWr 1 301H RWr 21
2E2H RWr 2 302H RWr 22
2E3H RWr 3 303H RWr 23
2
2E4H RWr 4
10
304H RWr 24
2E5H RWr 5 305H RWr 25
2E6H RWr 6 306H RWr 26
2E7H RWr 7 307H RWr 27
3
2E8H RWr 8
11
308H RWr 28
2E9H RWr 9 309H RWr 29
2EAH RWr A 30AH RWr 2A
2EBH RWr B 30BH RWr 2B
4
2ECH RWr C
12
30CH RWr 2C
2EDH RWr D 30DH RWr 2D
2EEH RWr E 30EH RWr 2E
2EFH RWr F 30FH RWr 2F
5
2F0H RWr 10
13
310H RWr 30
2F1H RWr 11 311H RWr 31
2F2H RWr 12 312H RWr 32
2F3H RWr 13 313H RWr 33
6
2F4H RWr 14
14
314H RWr 34
2F5H RWr 15 315H RWr 35
2F6H RWr 16 316H RWr 36
2F7H RWr 17 317H RWr 37
7
2F8H RWr 18
15
318H RWr 38
2F9H RWr 19 319H RWr 39
2FAH RWr 1A 31AH RWr 3A
2FBH RWr 1B 31BH RWr 3B
8
2FCH RWr 1C
2FDH RWr 1D
2FEH RWr 1E
2FFH RWr 1F
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-31
4.6.10 Link special relay (SB) and link special register (SW)
1) Link special relay (SB)
The data link status is stored in the form of bit ON/OFF information.
Buffer memory addresses 5E0H to 5FFH correspond to SB0000 to SB01FF.
For the details of link special relay (SB0000 to SB01FF), refer to Section 9.3.
The table below shows the relationship between the buffer memory addresses 5E0H to
5FFH and SB0000 to SB01FF.
2) Link special register (SW)
The data link status is stored in the form of word information.
Buffer memory addresses 600H to 7FFH correspond to SW0000 to SW01FF.
For the details of link special register (SW0000 to SW01FF), refer to Section 9.3.
Address b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b33 b2 b1 b0
5E0H F E D C B A 9 8 7 6 5 4 3 2 1 0
5E1H 1F 1E 1D 1C 1B 1A 19 18 17 16 15 14 13 12 11 10
5E2H 2F 2E 2D 2C 2B 2A 29 28 27 26 25 24 23 22 21 20
5E3H 3F 3E 3D 3C 3B 3A 39 38 37 36 35 34 33 32 31 30
5E4H 4F 4E 4D 4C 4B 4A 49 48 47 46 45 44 43 42 41 40
5E5H 5F 5E 5D 5C 5B 5A 59 58 57 56 55 54 53 52 51 50
5E6H 6F 6E 6D 6C 6B 6A 69 68 67 66 65 64 63 62 61 60
5E7H 7F 7E 7D 7C 7B 7A 79 78 77 76 75 74 73 72 71 70
5E8H 8F 8E 8D 8C 8B 8A 89 88 87 86 85 84 83 82 81 80
5E9H 9F 9E 9D 9C 9B 9A 99 98 97 96 95 94 93 92 91 90
5EAH AF AE AD AC AB AA A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
5EBH BF BE BD BC BB BA B9 B8 B7 B6 B5 B4 B3 B2 B1 B0
5ECH CF CE CD CC CB CA C9 C8 C7 C6 C5 C4 C3 C2 C1 C0
5EDH DF DE DD DC DB DA D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
5EEH EF EE ED EC EB EA E9 E8 E7 E6 E5 E4 E3 E2 E1 E0
5EFH FF FE FD FC FB FA F9 F8 F7 F6 F5 F4 F3 F2 F1 F0
5F0H 10F 10E 10D 10C 10B 10A 109 108 107 106 105 104 103 102 101 100
5F1H 11F 11E 11D 11C 11B 11A 119 118 117 116 115 114 113 112 111 110
5F2H 12F 12E 12D 12C 12B 12A 129 128 127 126 125 124 123 122 121 120
5F3H 13F 13E 13D 13C 13B 13A 139 138 137 136 135 134 133 132 131 130
5F4H 14F 14E 14D 14C 14B 14A 149 148 147 146 145 144 143 142 141 140
5F5H 15F 15E 15D 15C 15B 15A 159 158 157 156 155 154 153 152 151 150
5F6H 16F 16E 16D 16C 16B 16A 169 168 167 166 165 164 163 162 161 160
5F7H 17F 17E 17D 17C 17B 17A 179 178 177 176 175 174 173 172 171 170
5F8H 18F 18E 18D 18C 18B 18A 189 188 187 186 185 184 183 182 181 180
5F9H 19F 19E 19D 19C 19B 19A 199 198 197 196 195 194 193 192 191 190
5FAH 1AF 1AE 1AD 1AC 1AB 1AA 1A9 1A8 1A7 1A6 1A5 1A4 1A3 1A2 1A1 1A0
5FBH 1BF 1BE 1BD 1BC 1BB 1BA 1B9 1B8 1B7 1B6 1B5 1B4 1B3 1B2 1B1 1B0
5FCH 1CF 1CE 1CD 1CC 1CB 1CA 1C9 1C8 1C7 1C6 1C5 1C4 1C3 1C2 1C1 1C0
5FDH 1DF 1DE 1DD 1DC 1DB 1DA 1D9 1D8 1D7 1D6 1D5 1D4 1D3 1D2 1D1 1D0
5FEH 1EF 1EE 1ED 1EC 1EB 1EA 1E9 1E8 1E7 1E6 1E5 1E4 1E3 1E2 1E1 1E0
5FFH 1FF 1FE 1FD 1FC 1FB 1FA 1F9 1F8 1F7 1F6 1F5 1F4 1F3 1F2 1F1 1F0
FX2N-16CCL-M CC-Link System Master Block Specification 4
4-32
MEMO
Functions 5
5-1
5. Functions
This chapter describes the functions of the CC-Link master block for the FX Series.
5.1 Function List
Table 5.1:
Item Function summary Reference
Communication between
master station and remote
I/O stations
Transfers the ON/OFF information with remote I/O stations. 5.2
Communication between
master station and remote
device stations
Transfers the ON/OFF information and the numeric data with
remote device stations.
5.3
Communication in
compound system
Transfers data with remote I/O stations and remote device
stations.
5.4
Reserved station function
Sets remote stations to be connected in the future as reserved
ones so that such stations are not handled as data link faulty
stations.
If a connected station is set as a reserved one, data link is
disabled in the station.
5.5
Error invalid station function
Sets remote stations as "error invalid" so that such stations are
not handled as data link faulty stations.
5.6
Data link status setting
against error in master
station PLC CPU
Sets the data link status for a case in which an operation stop
error occurs in the master station PLC.
5.7
Parameter registration to
EEPROM
Registers the parameters to the EEPROM built in the master
module so that the parameters do not have to be written every
time the master module starts up.
7.1.1
Setting of input data status
from data link faulty station
Sets the status (clear or keep) of the data input (received) from
a station in which data link fails due to power OFF, etc.
5.8
Module reset function from
sequence program
Resets a module from a sequence program without resetting
the PLC when the switch settings are changed or an error
occurs in the module.
5.9
Data link stop/restart
Stops and restarts the data link while the data link is executed
by the write request for data link startup by buffer memory
parameters (BFM#AH b6) or the write request for data link
startup by EEPROM parameters (BFM#AH b8).
5.10
RAS
function
Automatic return
function
Allows a module which was disconnected from the data link by
power OFF, etc. to automatically join the data link again when it
recovers normal status.
5.11.1
Slave station
cutoff function
Cuts off only modules in which data link is disabled by power
OFF, etc., and continues the data link using only normal
modules.
5.11.2
Data link status
check (SB/SW)
Allows to check the data link status.
This function is useful to interlock in a sequence program, etc.
9.3
Offline test
Executes the following tests:
Hardware test: Checks operations in a single module.
Line test: Checks the connection status of modules.
Parameter verification test: Verifies the contents of the
preset parameters.
8.3
8.7
8.8
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-2
5.2 Communication between Master Station and Remote I/O Stations
This section describes the overview of the communication between the master station and
remote I/O stations.
[Data link startup]
1) The PLC sets to ON the write refresh command (BFM#AH b0), and makes the data of the
remote output (RY) effective.
When the write refresh command (BFM#AH b0) is OFF, all data of the remote output (RY) is
treated as "0 (OFF)".
2) The PLC sets to ON the write data link startup by EEPROM parameters (BFM#AH b8) to
start the data link.
However, parameters should be registered to the EEPROM in advance.
When the data link starts normally, the read data link status in host station (BFM#AH b1)
turns ON.
Point
The data link can be started also from the parameters written in the "parameter
information area" in the buffer memory. (Refer to Chapter 7.)
PLC Master station
Refresh command
Data link startup by
EEPROM parameters
Remote I/O station
SET
FROM
TO
M
M
BFM#AH b0
SET
Buffer memory
Remote input
(RX)
Remote output
(RY)
BFM#AH b8
Input Link scan
Output Link scan

FX2N-16CCL-M CC-Link System Master Block Functions 5

5-3
[Remote input]
3) The input status of the remote I/O stations is automatically (for each link scan) stored in the
buffer memory "remote input (RX)" in the master station.
4) The PLC receives the input status stored in the buffer memory "remote input (RX)" using
the FROM instruction.
[Remote output]
5) The PLC writes the ON/OFF information output from the remote I/O station to the buffer
memory "remote output (RY)" using the TO instruction.
6) The output status stored in the buffer memory "remote output (RY)" is automatically (for
each link scan) output from the remote I/O stations.
Master station
RX0F ~ RX00
RX1F ~ RX10
RX2F ~ RX20
RX3F ~ RX30
RX4F ~ RX40
~
RX1DF ~ RX1D0
PLC
FROM
X0F ~ X00
X0F ~ X00
Remote I/O station
(Station No. 1: Occupies 1 station)
Remote I/O station
(Station No. 2: Occupies 1 station)
32-point module 16-point module
Remote input (RX)
X1F ~ X10
Y0F ~ Y00
Y1F ~ Y10
Master station
RY0F ~ RY00
RY1F ~ RY10
RY2F ~ RY20
RY3F ~ RY30
RY4F ~ RY40
~
RY1DF ~ RY1D0
PLC
TO
Remote I/O station
(Station No. 3: Occupies 1 station)
Remote I/O station
(Station No. 4: Occupies 1 station)
32-point module 16-point module
RY5F ~ RY50
RY6F ~ RY60
RY7F ~ RY70
RY8F ~ RY80
Remote output (RY)
Y0F ~ Y00
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-4
5.3 Communication between Master Station and Remote Device Stations
This section describes the overview of the communication between the master station and
remote device stations.
PLC Master station
Refresh command
Data link startup by
EEPROM parameters
Remote device station
SET
FROM
TO
M
M
BFM#AH b0
SET
Buffer memory
Remote input
(RX)
Remote output
(RY)
BFM#AH b8
Remote input
(RX)
Link scan
Link scan
1)
2)
4)
5)
3)
6)
TO
FROM
Remote register
(RWw)
Remote register
(RWr)
7)
10)
8)
9)
Remote output
(RY)
Remote
register
(RWw)
Remote
register
(RWr)
Link scan
Link scan
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-5
[Data link startup]
1) The PLC sets to ON the write refresh command (BFM#AH b0), and makes the data of the
remote output (RY) effective.
When the write refresh command (BFM#AH b0) is OFF, all data of the remote output (RY) is
treated as "0 (OFF)".
2) The PLC sets to ON the write data link startup (BFM#AH b8) by EEPROM parameters to
start the data link.
However, parameters should be registered to the EEPROM in advance.
When the data link starts normally, the read data link status in host station (BFM#AH b1)
turns ON.
[Remote input]
3) The remote input (RX)of the remote device stations is automatically (for each link scan)
stored in the buffer memory "remote input (RX)" in the master station.
4) The PLC receives the input status stored in the buffer memory "remote input (RX)" using
the FROM instruction.
Point
The data link can be started also from the parameters written in the "parameter
information area" in the buffer memory. (Refer to Chapter 7.)
Master station
RX0F ~ RX00
RX1F ~ RX10
RX2F ~ RX20
RX3F ~ RX30
RX4F ~ RX40
~
RX1DF ~ RX1D0
PLC
FROM
Remote device station
(Station No. 1: Occupies 2 stations)
Remote device station
(Station No. 3: Occupies 2 stations)
RX5F ~ RX50
RX6F ~ RX60
RX7F ~ RX70
RX8F ~ RX80
Remote input (RX)
RX0F ~ RX00
RX1F ~ RX10
Remote input (RX)
RX0F ~ RX00
RX1F ~ RX10
Remote input (RX)
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-6
[Remote output]
5) The PLC writes the ON/OFF information of the remote output (RY) in the remote device
stations to the buffer memory "remote output (RY)" using the TO instruction.
6) The remote output (RY) in the remote device stations is automatically (for each link scan)
set to ON or OFF in accordance with the output status stored in the buffer memory "remote
output (RY)".
Master station
RY0F ~ RY00
RY1F ~ RY10
RY2F ~ RY20
RY3F ~ RY30
RY4F ~ RY40
~
RY1DF ~ RY1D0
PLC
TO
Remote device station
(Station No. 1: Occupies 2 stations)
Remote device station
(Station No. 3: Occupies 2 stations)
RY5F ~ RY50
RY6F ~ RY60
RY7F ~ RY70
RY8F ~ RY80
Remote output(RY)
RY0F ~ RY00
RY1F ~ RY10
Remote output(RY)
RY0F ~ RY00
RY1F ~ RY10
Remote output (RY)
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-7
[Write to remote register (RWw)]
7) The PLC writes the transmission data to the buffer memory "remote register (RWw)" using
the TO instruction.
8) The data stored in the buffer memory "remote register (RWw)" is automatically transmitted
to the remote register (RWw) in the remote device stations.
Master station
RWw0
RWw1
RWw2
RWw3
RWw4
~
RWw3B
PLC
TO
Remote device station
(Station No. 1: Occupies 2 stations)
Remote device station
(Station No. 3: Occupies 2 stations)
RWw5
RWw6
RWw7
RWw8
Remote register (RWw) Remote register (RWw)
Remote register (RWw)
RWw8
RWw9
RWwA
RWwB
RWwC
RWwD
RWwE
RWwF
RWw10
RWw0
RWw1
RWw2
RWw3
RWw4
RWw5
RWw6
RWw7
RWw0
RWw1
RWw2
RWw3
RWw4
RWw5
RWw6
RWw7
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-8
[Read from remote register (RWr)]
9) The data of the remote register (RWr) in the remote device stations is automatically stored
in the buffer memory "remote register (RWr)" in the master station.
10)The PLC receives the data of the remote register (RWr) in the remote device stations
stored in the buffer memory "remote register (RWr)" using the FROM instruction.
Master station
RWr0
RWr1
RWr2
RWr3
RWr4
~
RWr3B
PLC
FROM
Remote device station
(Station No. 1: Occupies 2 stations)
Remote device station
(Station No. 3: Occupies 2 stations)
RWr5
RWr6
RWr7
Remote register (RWr) Remote register (RWr)
Remote register (RWr)
RWr8
RWr9
RWrA
RWrB
RWrC
RWrD
RWrE
RWrF
RWr10
RWr0
RWr1
RWr2
RWr3
RWr4
RWr5
RWr6
RWr7
RWr0
RWr1
RWr2
RWr3
RWr4
RWr5
RWr6
RWr7
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-9
5.4 Communication in Compound System
This section describes the overview of the communication in the system in which remote I/O
stations and remote device stations exist together.
[Data link startup]
1) The PLC sets to ON the write refresh command (BFM#AH b0), and makes the data of the
remote output (RY) effective.
When the write refresh command (BFM#AH b0) is OFF, all data of the remote output (RY) is
treated as "0 (OFF)".
2) The PLC sets to ON the write data link startup (BFM#AH b8) by EEPROM parameters to
start the data link.
However, parameters should be registered in the EEPROM in advance.
When the data link starts normally, the read data link status in host station (BFM#AH b1)
turns ON.
Point
The data link can be started also from the parameters written in the "parameter
information area" in the buffer memory. (Refer to Chapter 7.)
PLC Master station
Refresh command
Data link startup by
EEPROM parameters
Remote I/O station
(station No. 1)
SET
FROM
TO
M
M
BFM#AH b0
SET
Remote input (RX)
Receive area for data
from remote I/O station
(station No. 1)
BFM#AH b8
Input
1)
2)
4)
5)
3)
TO
FROM
7)
10)
Receive area for data
from remote device
station (station No. 2)
Buffer memory
Remote output (RY)
Transmission area for
data to remote I/O
station (station No. 1)
Transmission area for
data to remote device
station (station No. 2)
Remote register (RWw)
Prohibited to use
(station No. 1)
Transmission area for
data to remote device
station (station No. 2)
Remote register (RWr)
Prohibited to use
(station No. 1)
Receive area for data
from remote device
station (station No. 2)
3)
Remote device station
(station No. 2)
Remote input
(RX)
Output
6)
Remote output
(RY)
Remote register
(RWw)
Remote register
(RWr)
6)
8)
9)
FROM
4)
TO
5)
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-10
[ON/OFF information from the remote I/O station/remote device station to the master
station]
3) The input status of the input (X) in the remote I/O station and the remote input (RX)in the
remote device station is automatically (for each link scan) stored in the buffer memory
"remote input (RX)" in the master station.
4) The PLC receives the input status stored in the buffer memory "remote input (RX)" using
the FROM instruction.
Master station
RX0F ~ RX00
RX1F ~ RX10
RX2F ~ RX20
RX3F ~ RX30
RX4F ~ RX40
~
RX1DF ~ RX1D0
Remote I/O station
(station No.1
: Occupies 1 station)
Remote device station
(station No.2
: Occupies 2 stations)
RX5F ~ RX50
RX6F ~ RX60
RX7D ~ RX70
RX8F ~ RX80
Remote input (RX)
Remote input (RX)
RX9F ~ RX90
RXAF ~ RXA0
RXBF ~ RXB0
RXCF ~ RXC0
RXDF ~ RXD0
RXEF ~ RXE0
RXFD ~ RXF0
RX10F ~ RX100
X0F ~ X00
X1F ~ X10
RX0F ~ RX00
RX1F ~ RX10
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-11
[ON/OFF information from the master station to the remote I/O station/remote device
station]
5) The PLC writes the ON/OFF information to be transmitted to the remote I/O station and the
remote device station to the buffer memory "remote output (RY)" in the master station using
the TO instruction.
6) The output status of the buffer memory "remote output (RY)" in the master station is
automatically (for each link scan) transmitted to the output (RY) in the remote I/O station
and the remote output (RY) in the remote device station.
Master station
RY0F ~ RY00
RY1F ~ RY10
RY2F ~ RY20
RY3F ~ RY30
RY4F ~ RY40
~
RY1DF ~ RY1D0
Remote I/O station
(station No.1
: Occupies 1 station)
Remote device station
(station No. 2
: Occupies 2 stations)
RY5F ~ RY50
RY6F ~ RY60
RY7D ~ RY70
RY8F ~ RY80
Remote output (RY)
Remote output (RY)
RY9F ~ RY90
RYAF ~ RYA0
RYBF ~ RYB0
RYCF ~ RYC0
RYDF ~ RYD0
RYEF ~ RYE0
RYFD ~ RYF0
RY10F ~ RY100
Y0F ~ Y00
Y1F ~ Y10
RY0F ~ RY00
RY1F ~ RY10
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-12
[Word information from the master station to the remote device station]
7) The PLC writes the word information to be transmitted to the remote device station to the
buffer memory "remote register (RWw)" in the master station using the TO instruction.
8) The information of the buffer memory "remote register (RWw)" is automatically (for each link
scan) stored in the remote register (RWw) in the remote device station.
Master station
RWw0
RWw1
RWw2
RWw3
RWw4
~
RWw3B
Remote I/O station
(station No.1
: Occupies 1 station)
Remote device station
(station No. 2
: Occupies 2 stations)
RWw5
RWw6
RWw7
RWw8
Remote register (RWw)
Remote register (RWw)
RWw8
RWw9
RWwA
RWwB
RWwC
RWwD
RWwE
RWwF
RWw10
RWw11
RWw12
RWw13
RWw14
RWw15
RWw16
RWw17
RWw18
RWw19
RWw1A
RWw1B
RWw1C
RWw1D
RWw1E
RWw1F
RWw0
RWw1
RWw2
RWw3
RWw4
RWw5
RWw6
RWw7
RWw20
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-13
[Word information from the remote device station to the master station]
9) The data of the remote register (RWr) in the remote device station is automatically (for each
link scan) stored in the remote register (RWr) in the master station.
10)The PLC receives the data of the remote device station stored in the buffer memory
"remote register (RWr)" using the FROM instruction.
Master station
RWr0
RWr1
RWr2
RWr3
RWr4
~
RWr3B
Remote I/O station
(station No.1
: Occupies 1 station)
Remote device station
(station No. 2
: Occupies 2 stations)
RWr5
RWr6
RWr7
RWr8
Remote register (RWr)
Remote register (RWr)
RWr9
RWrA
RWrB
RWrC
RWrD
RWrE
RWrF
RWr10
RWr11
RWr12
RWr13
RWr14
RWr15
RWr16
RWr17
RWr18
RWr19
RWr1A
RWr1B
RWr1C
RWr1D
RWr1E
RWr1F
RWr0
RWr1
RWr2
RWr3
RWr4
RWr5
RWr6
RWr7
RWr20
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-14
5.5 Reserved Station Function
This function sets remote stations to be connected in the future (which are not currently
connected) as reserved ones so that such stations are not handled as data link faulty stations.
1) Setting method
Specify reserved stations using the parameter BFM#10H.
Set to ON the bits corresponding to the station numbers of the stations to be reserved.
However, for a remote station module occupying two or more stations, set to ON only the bit
corresponding to the station number set by the station number setting switch in the module.
The table below shows the buffer memory configuration. (Numbers 1 to 15 indicate station
numbers)
2) Setting example
a) System configuration example
When one remote device station and one remote I/O station are to be connected in the
future to the system in which two remote I/O stations and one remote device station are
connected
b) Buffer memory setting example
Set to ON the 3rd bit corresponding to the station No. 4 and the 8th bit corresponding to
the station No. 9. (Set "108H" to the BFM#10H.)
Point
If a connected remote station is set as a reserved one, data link is disabled in the
remote station.
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 10H 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 10H 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0
0 1 0 8
Master
station
Station No. 1
Remote I/O
station (occupies
1 station)
Station No. 3
Remote
device station
(occupies 4
stations)
Station No. 4
Remote I/O
station (occupies
1 station)
Station No. 8
Station No. 9
Modules to be connected in the future
Remote I/O
station (occupies
1 station)
Remote
device station
(occupies 2
stations)
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-15
5.6 Error Invalid Station Function
This function sets remote stations in which data link is disabled by power OFF, etc. as error
invalid ones so that such stations are not handled as data link faulty stations.
Be careful, however, for errors will not be detected at all in stations set as invalid
stations.
1) Setting method
Specify invalid stations using the parameter BFM#14H
Set to ON the bits corresponding to the station numbers of the stations to be made invalid.
However, for a remote station occupying two or more stations, set to ON only the bit
corresponding to the station number set by the station number setting switch in the module.
The table below shows the buffer memory configuration. (Numbers 1 to 15 indicate station
numbers)
2) Setting example
a) System configuration example
When the remote I/O station No. 3 and the remote device station No. 7 are made invalid
in the system in which two remote I/O stations and three remote device stations are con-
nected
b) Buffer memory setting example
Set to ON the 2nd bit corresponding to the station No. 3 and the 6th bit corresponding to
the station No. 7. (Set "44H" to the BFM#14H.)
Point
If a remote station set as invalid station is also set as reserved station, the reserved
station function has the priority.
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 14H 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
BFM# 14H 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0
0 0 4 4
Master
station
Station No. 1
Remote I/O
station (occupies
1 station)
Station No. 3
Modules to be set as error invalid stations
Remote
device station
(occupies 2
stations) Remote I/O
station (occupies
1 station)
Station No. 4
Remote
device station
(occupies 2
stations)
Station No. 5
Remote
device station
(occupies 4
stations)
Station No. 7
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-16
5.7 Data Link Status Setting against Error in Master Station PLC
This function sets the data link status for a case in which an operation stop error occurs in the
master station PLC.
[Setting method]
Set the operation status to the parameter information area "operation specification against
CPU down (BFM# 6H)" in the buffer memory in the master station.
0: Stop (default)
1: Continue
Point
Even if an operation continue error occurs in the master station PLC, the data link
continues.
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-17
5.8 Setting of Input Data Status from Data Link Faulty Station
The status of the data input (received) from a data link faulty station can be set.
1) Target input (received) data
The figure below shows the buffer memory area regarded as the setting target.
2) Setting method
Set the status using the condition setting DIP switch SW4 in the master block.
OFF: Clear (setting at shipment)
ON : Keeps the status right before error
Point
When a data link faulty station is set as error invalid station, the data (remote input
RX and remote output RY) input from the station is kept without regard to the setting
of the SW4.
Station No. 1
Station No. 2
Remote input (RX)
Remote output (RY)
Master station
Remote I/O station
(station No. 1)
Input
Remote input (RX)
Output
Remote output (RY)
Remote device station
(station No. 2)
Station No. 3
Station No. 4
Station No. 1
Station No. 2
Station No. 3
Station No. 4
Remote register (RWw)
Station No. 1
Station No. 2
Station No. 3
Station No. 4
Remote register (RWr)
Station No. 1
Station No. 2
Station No. 3
Station No. 4
Remote register
(RWw)
Remote register
(RWr)
: Target area of clear/keep
: Area kept without regard to the setting
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-18
5.9 Module Reset Function from Sequence Program
This function resets a module from a sequence program without resetting the PLC or the
master block when the switch settings are changed or an error occurs in the master block.
However, reset is disabled when there is an read module error (when the BFM#AH b0 is
ON).
The figure below shows a program example for module reset.
Point
Because the PLC is not initialized, operations of other modules are not affected at
all.
Remarks
Change from the mode 0 or the mode 2 to the test mode cannot be executed by the
write request for module reset (BFM#AH b4).
For such a change, turn off the power, then turn it on again.
M8000
FROM K0 HA K4M0 K1
Reads from BFM#AH.
BFM#AH M15 to M0
RUN monitor
Reset command
M4 (module reset acceptance completion)
M8000
RUN monitor
SET M24
RST M24
TO K0 HA K4M20 K1
Sets to ON the write request for
module reset.
Writes to BFM#AH.
M35 to M20 BFM#AH
Sets to OFF the write request for
module reset.
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-19
5.10 Data Link Stop/Restart
This function stops and restarts the data link in the host station.
When the data link is stopped in the master station, the data link is stopped in the entire
system.
1) The following link special relays are used in programs:
SB0000: Request for data link restart
SB0002: Request for data link stop
SB0041: Completion of data link restart
SB0045: Completion of data link stop
2) The figure below shows a program example to stop/restart the data link.
1) Relationship between the PLC and the master station
2) Program example
Point
When you have stopped the data link using SB0002, make sure to start up the data
link using SB0000.
PLC Master station
M15 ~ M0
M35 ~ M20
SB000F ~ SB0000
SB004F ~ SB0040
5E0H
5E4H
TO
FROM
Link special relay (SB)
M8000
FROM K0 H05E4 K4M20 K1
Reads the status of SB0040
to SB004F.
RUN monitor
Stop command
SET M2
RST M2
Turns ON M2 (SB0002) (data
link stop).
Turns ON M0 (SB0000) (data
link restart).
Turns OFF M2 (SB0002) (data
link stop).
M25(SB0045)
Restart
command
SET M0
RST M0
M21(SB0041)
M8000
TO K0 H05E0 K4M0 K1
RUN monitor
Writes to SB0000 to SB000F.
Data link stop
Data link restart
Turns OFF M0 (SB0000) (data
link restart).
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-20
5.11 RAS Function
The term "RAS" stands for "reliability, availability and serviceability", and refers to the total
operability of an automated facility.
5.11.1 Automatic return function
This function allows a module which was disconnected from the data link by power OFF, etc. to
automatically join the data link again when it recovers the normal status.
Set the automatic return function using the mode setting switch.
5.11.2 Slave station cutoff function
This function cuts off only remote stations in which data link is disabled by power OFF, etc.,
and continues the data link using only normal remote stations.
Table 5.2:
Mode setting switch Setting description Remarks
0 Online (automatic return allowed)
1 Unusable
2 Offline Data link disabled (disconnected status)
Point
When a cable is broken, the data link is disabled in the entire system because
terminal resistors do not function any more.
Master
station
Remote I/O
station
Remote I/O
station
Down
Remote
device
station
Remote
device
station
Terminal resistor Terminal resistor
Continues data link excluding the down station.
Master
station
Remote I/O
station
Remote I/O
station
Down
Remote
device
station
Remote
device
station
Terminal resistor Terminal resistor Wire breakage
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-21
5.11.3 Station number overlap check function
This function checks the status of actually connected stations when the write request for data
link start is given (when BFM#AH b6/b8 is set to ON), and checks whether the assigned station
numbers overlap.
Example:
Remote device station (station No. 1 occupying 4 stations)
Remote device station (station No. 4 occupying 2 stations)
However, if the starting head number overlaps, it is not
regarded as an overlap check target.
Example:
Remote device station (station No. 1 occupying 4 stations)
Remote device station (station No. 1 occupying 2 stations)
1) When there is an overlap, the M/S LED flashes and the overlap status is stored in SW0098.
2) Even if overlap exists, data link can be continued with other normally functioning stations.
3) When the switch setting is corrected to the normal status and the write request for data link
startup is given again (BFM#AH b6/b8 is set to ON), the M/S LED turns off and the data
stored in SW0098 is cleared.
Station
No. 1
Station
No. 2
Station
No. 3
Station
No. 4
Station
No. 4
Station
No. 5
Overlap
Station
No. 1
Station
No. 2
Station
No. 3
Station
No. 4
Overlap
at head
Station
No. 1
Station
No. 2
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-22
5.12 Temporary Error Invalid Station Specification Function
This function allows a remote station to be replaced in the online status without detecting an
error in the corresponding module.
Different from the error invalid station specification by parameters, error invalid stations can be
temporarily specified with arbitrary timing.
5.12.1 I/O status when temporary error invalid stations are specified
In a station specified as a temporary error invalid station, all the cyclic transmission data is
refreshed.
If an error occurs in a station specified as a temporary error invalid station, the input is kept and
the output is set to OFF.
5.12.2 Link special relays and registers (SB and SW) related to temporary error invalid station
specification function
This section describes the link special relays and registers related to the temporary error
invalid station specification function.
1) Link special relays (SB)
The table below shows the link special relays (SB) related to the temporary error invalid
station specification function.
Table 5.3:
Number
BFM
number
Name Description
Hex. Bit
SB0004 5E0H b4
Request for temporary
error invalid station
Determines the stations specified by SW0003 to
SW0004 as temporary error invalid stations.
OFF : Request not given
ON : Request given
SB0005 5E0H b5
Request for cancel of
temporary error invalid
station
Cancels the stations specified by SW0003 to SW0004
from temporary error invalid stations
OFF : Request not given
ON : Request given
SB0048 5E4H b8
Temporary error invalid
station acceptance
status
Indicates the acceptance status of the request for
temporary error invalid station.
OFF : Not accepted
ON : Accepted
SB0049 5E4H b9
Temporary error invalid
station completion
status
Indicates the acceptance completion status of the
temporary error invalid station request.
OFF : Not completed
ON : Completed (Determination as temporary
error invalid station is completed.)
SB004A 5E4H b10
Temporary error invalid
station cancel
acceptance status
Indicates the acceptance status of the request to
temporarily cancel the error invalid station.
OFF : Not accepted
ON : Accepted
SB004B 5E4H b11
Temporary error invalid
station cancel
completion status
Indicates the acceptance completion status of the
request to temporarily cancel the error invalid station.
OFF : Not completed
ON : Completed (Cancel of determination as
temporary error invalid station is completed.)
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-23
2) Link special registers (SW)
The table below shows the link special registers (SW) related to the temporary error invalid
station specification function.
*1 Only the bit of the head station number is set to ON.
Table 5.4:
Number
BFM
number
Hex.
Name Description
SW0003 603H
Specification of
multiple temporary
error invalid stations
Selects whether or not two or more stations are
specified as temporary error invalid stations.
00 : Specifies two or more stations stored in SW0004.
01 to 15: Specifies one station (station No. 1 to 15).
* The number specifies the station number of a station
to be specified as a temporary error invalid station.
SW0004 604H
Specification of
temporary error invalid
station
*1

Specifies temporary error invalid stations.
0: Does not specify as a temporary error invalid
station.
1: Specifies as a temporary error invalid station.
Numbers 1 to 15 above indicate the station numbers
SW0049 649H
Temporary error invalid
station request result
Stores the execution result of the request for
temporary error invalid station by SB0004.
0 : Normal
Any value other than 0: Stores an error code. (Refer
to Section 13.3.)
SW004B 64BH
Temporary error invalid
station cancel request
result
Stores the execution result of the request for cancel of
temporary error invalid station by SB0005.
0 : Normal
Any value other than 0: Stores an error code. (Refer
to Section 13.3.)
SW007C 67CH
Temporary error invalid
station specification
status
*1
Stores the temporary error invalid station specification
status.
0: Not specified as temporary error invalid station
1: Specified as temporary error invalid station
Numbers 1 to 15 above indicate the station numbers
Point
1) When both the request for temporary error invalid station and the request for
cancel of temporary error invalid station are given at the same time, the request
for cancel of temporary error invalid station has the priority.
2) In a station occupying two or more stations, only the head station number is
effective.
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0004 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW007C 15 14 13 ~ 4 3 2 1
FX2N-16CCL-M CC-Link System Master Block Functions 5
5-24
5.12.3 Temporary error invalid station specification procedure
This section describes the procedure to execute the temporary error invalid station function.
Point
1) Even if the request for temporary error invalid station is executed for a faulty
station, the error information is not cleared.
The temporary error invalid station specification function is effective only to errors
which occur after the specification.
2) The request for temporary error invalid and the request for cancel of temporary
error invalid station are not effective to stations which are specified as error
invalid stations by parameter.
Select whether two or more stations are to be specified as temporary error
invalid stations (SW0003).
(00: Two or more stations, 01 to 15: One station)
Set to ON the request for temporary error invalid station (SB0004).
Turn off the power of temporary error invalid stations, and replace them.
Turn on the power of temporary error invalid stations.
Set to ON the request for cancel of temporary error invalid station (SB0005).
Data Link Processing Time 6
6-1
6. Data Link Processing Time
6.1 Status of Each Station when an Error has Occurred
The table below shows the status of each station when an error has occurred.
*1 Because the BFM#AH b0 (refresh command) is set to OFF.
Table 6.1:
Data link status
Master station
Remote input (RX)
Remote
output (RY)
Remote
register
(RWw)
Remote register
(RWr)
When the master station PLC is stopped
(data link continues)
Continue
Handles "0"
in any case.
*1
Continue Continue
When data link is
stopped in the
entire system
Input data
status setting
for faulty
station (SW4)
Clear Clear
Keep
Keep Keep
When a
communication
error occurred (due
to power OFF, etc.)
in a remote I/O
station
Input data
status setting
for faulty
station (SW4)
Clear
Clears the receive
area for data from
remote I/O station
with a
communication
error.
Continue Continue Continue
Keep
Keeps the receive
area for data from
remote I/O station
with a
communication
error.
When a
communication
error occurred
(due to power
OFF, etc.) in a
remote device
station
Clear
Clears the receive
area for data from
remote device
station with a
communication
error.
Continue Continue
Keeps the receive
area for data from
remote device
station with a
communication
error.
Keep
Keeps the receive
area for data from
remote device
station with a
communication
error.
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Data Link Processing Time 6
6-2
.
Table 6.2:
Data link status
Remote I/O station Remote device station
Input Output
Remote
input
(RX)
Remote
output
(RY)
Remote
register
(RWw)
Remote
register
(RWr)
When the master station PLC is stopped
(data link continues)
Continue All OFF Continue All OFF Continue Continue
When data link is
stopped in the
entire system
Input data
status setting
for faulty
station (SW4)
Clear
All OFF All OFF
Keep
When a
communication
error occurred (due
to power OFF, etc.)
in a remote I/O
station Input data
status setting
for faulty
station (SW4)
Clear
All OFF Continue Continue Continue Continue
Keep
When a
communication
error occurred
(due to power
OFF, etc.) in a
remote device
station
Clear
Continue Continue
Keep
FX2N-16CCL-M CC-Link System Master Block Data Link Processing Time 6
6-3
6.2 Link Scan Time
The link scan time in the CC-Link system is calculated using the expression below.
Example: When the transmission speed is 2.5 Mbps in the system configuration below
BT = 3.2 ST = 1100
NI = 7 8 800 + (3 15) = 845
NW = 7 8 900 + {(4 50) = 1100
a = 3 b = 4
N = 5
ni = 7
nw = 4
LS = 3.2 {29.4 + (8 4.8) + (8 9.6) + (5 32.4) + (7 4.8) + (4 9.6)} + 1100
= 2311.52 [s]
= 2.31 [ms]
LS = BT {29.4 + (NI 4.8) + (NW 9.6) + (N 32.4) + (ni 4.8) + (nw 9.6)} + ST
+ {Number of communication faulty stations 48 BT Number of retries}* [s]
BT : Constant (transmission speed)
NI : Last station number in a and b (including the number of occupied stations and
excluding the number of reserved stations)
NW: Last station number in b (including the number of occupied stations and excluding
the number of reserved stations)
N : Number of connected modules (excluding reserved station)
ni : a + b (excluding reserved stations)
nw : b (excluding reserved stations)
ST : Constant (larger value of () and ()) (If b is 0, () should be ignored.)
800 + (a 15)
900 + (b 50)
a : Total number of stations occupied by remote I/O stations
b : Total number of stations occupied by remote device stations
* : Only when there are communication faulty stations (including error invalid stations
and temporary error invalid stations)
Transmission speed 156kbps 625kbps 2.5Mbps 5Mbps 10Mbps
BT 51.2 12.8 3.2 1.6 0.8
Last station Number 1 to 8 9 to 15
NI,NW 8 16
[Link scan time (LS)]
Master
station
Remote I/O
station
Remote I/O
station
Remote I/O
station
Remote device
station
Remote device
station
Station No. 1
*1
Station No. 2
*1
Station No. 3
*1
Station No. 4
*2
Station No. 6
*2
*1: Occupies 1 station. *2: Occupies 2 station.
FX2N-16CCL-M CC-Link System Master Block Data Link Processing Time 6
6-4
6.3 Transmission Delay Time
This section describes the transmission delay time (time required for data transmission).
6.3.1 Master station remote I/O station
1) Master station (RX) remote I/O station (input)
[Calculation expression]
SM + LS 2 + Remote I/O station response time [ms]
SM : Scan time of master stations sequence program
LS : Link scan time (Refer to Section 6.2.)
[Data flow]
2) Master station (RY) remote I/O station (output)
[Calculation expression]
SM + LS 3 + Remote I/O station response time [ms]
SM : Scan time of master stations sequence program
LS : Link scan time (Refer to Section 6.2.)
[Data flow]
PLC
FROM FROM
Buffer memory in master station
(Remote input RX)
Link scan (LS)
Remote I/O station
PLC
TO TO
Buffer memory in master station
(Remote output RY)
Link scan (LS)
Remote I/O station
FX2N-16CCL-M CC-Link System Master Block Data Link Processing Time 6
6-5
6.3.2 Master station remote device station
1) Master station (RX) remote device station (RX)
[Calculation expression]
SM + LS 2 + Remote device station processing time [ms]
SM : Scan time of master stations sequence program
LS : Link scan time (Refer to Section 6.2.)
[Data flow]
2) Master station (RY) remote device station (RY)
[Calculation expression]
SM + LS 3 + Remote device station processing time [ms]
SM : Scan time of master stations sequence program
LS : Link scan time (Refer to Section 6.2.)
[Data flow]
PLC
FROM FROM
Buffer memory in master station
(Remote input RX)
Link scan (LS)
Remote device station
RXn (input signal)
PLC
TO TO
Buffer memory in master station
(Remote output RY)
Link scan (LS)
Remote device station
RYn (output signal)
FX2N-16CCL-M CC-Link System Master Block Data Link Processing Time 6
6-6
3) Master station (RWw) remote device station (RWw)
[Calculation expression]
SM + LS 3 + Remote device station processing time [ms]
SM : Scan time of master stations sequence program
LS : Link scan time (Refer to Section 6.2.)
[Data flow]
4) Master station (RWr) remote device station (RWr)
[Calculation expression]
SM + LS 2 + Remote device station processing time [ms]
SM : Scan time of master stations sequence program
LS : Link scan time (Refer to Section 6.2.)
[Data flow]
PLC
TO TO
Buffer memory in master station
(Remote register RWw)
Link scan (LS)
Remote device station
Remote register (RWw)
PLC
FROM FROM
Buffer memory in master station
(Remote register RWr)
Link scan (LS)
Remote device station
Remote register (RWr)
Parameter Setting 7
7-1
7. Parameter Setting
This chapter describes the parameter setting required to execute data link in the CC-Link
system.
7.1 Procedure from Parameter Setting to Data Link Startup
This section describes the flow from parameter setting to data link startup.
7.1.1 Relationship among buffer memory, EEPROM and internal memory
This section describes the relationship among the buffer memory, the EEPROM and the
internal memory in the master station.
1) Buffer memory
This is a temporary storage area to write the parameter information to the EEPROM or the
internal memory.
Write the parameter information to the buffer memory using a sequence program.
(When the power of the master block is turned off, the parameter information is erased.)
2) EEPROM
Only by setting to ON the write request for data link startup by EEPROM parameters
(BFM#AH b8), data link can be started up.
This eliminates the necessity to write parameters to the buffer memory every time the
master station starts up.
However, the parameter should be registered in advance to the EEPROM by the write
request for parameter registration to EEPROM (BFM#AH b10).
Even when the power of the master block is turned off, the parameter information stored in
the EEPROM remains stored.
The registration limit to the EEPROM is 10,000 times.
3) Internal memory
Data link is executed using the parameter information stored in the internal memory.
When the power of the master block is turned off, the parameter information is erased.
Parameter
information area
Buffer memory
The parameter
information is
erased when the
power is turned off.
E
2
PROM
Internal memory
Data link is
executed using this
parameter
information.
M SET
BFM#AH b10
TO
M SET
BFM#AH b8
M SET
BFM#AH b6
PLC Master station
The parameter
information
remains stored
even when the
power is turned off.
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-2
Point
In debugging (startup) in which set values of parameters are not determined, set
parameters by executing "setting and operation using the buffer memory" (Refer
to 7.3.1.).
After debug (startup) is completed, register parameter set values to the
EEPROM, then execute "operation based on parameters registered in the
EEPROM" (Refer to 7.3.2.).
However, when a work for setting parameters again is expected accompanied by
changes and additions to the system after operation, operation can be executed
using a program for "setting and operation using the buffer memory" without
registering parameter set values to the EEPROM.
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-3
7.1.2 Procedure from parameter setting to data link startup
Perform the procedure shown below.
Write the data (such as the
number of connected
modules and the number of
retries) to the buffer memory
"parameter information area"
in the master station.
TO
PLC
PLC
By the write request for data link
startup by buffer memory
parameters (BFM#AH b6), the
contents of the buffer memory
"parameter information area" are
written to the internal memory.
Then the data link automatically
starts.
M SET
Master station
Parameter
information
area
Buffer memory
E
2
PROM
Internal
memory
Debug completed?
PLC
By the write request for
parameter registration to
EEPROM (BFM#AH b10), the
contents of the buffer
memory "parameter
information area" is written to
the EEPROM.
M SET
BFM#AH b6
BFM#AH b10
PLC
By the write request for data
link startup by EEPROM
parameters (BFM#AH b8), the
parameter information stored
in the EEPROM is transferred
to the internal memory.
Then the data link
automatically starts.
M SET
BFM#AH b8
Master station
Parameter
information
area
Buffer memory
E
2
PROM
Internal
memory
NO
YES
Master station
Parameter
information
area
Buffer memory
E
2
PROM
Internal
memory
Master station
Parameter
information
area
Buffer memory
E
2
PROM
Internal
memory
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-4
7.2 Parameter Setting Items
The table below shows the items set in the buffer memory "parameter information area" in the
master station.
For details of each item, refer to Section 4.6.2.
Table 7.1:
Setting item Description
BFM#
Hex.
Number of
connected
modules
Sets the number of remote station modules (including reserved stations)
connected to the master station.
Default value : 8 (modules)
Setting range : 1 to 15 (modules)
1H
Number of
retries
Sets the number of retries executed when communication error occurs.
Default value : 3 (times)
Setting range : 1 to 7 (times)
2H
Number of
automatic
return
modules
Sets the number of remote station modules which can recover in one link
scan.
Default value : 1 (module)
Setting range : 1 to 10 (modules)
3H
Operation
specification
against CPU
down
Specifies the data link status when an error occurs in the master station
PLC CPU.
Default value : 0 (stop)
Setting range : 0 (stop), 1 (continue)
6H
Reserved
station
specification
Specifies reserved stations.
Default value : 0 (no setting)
Setting range : Set to ON the bits corresponding to the station numbers
10H
Invalid
station
specification
Specifies invalid stations.
Default value : (no setting)
Setting range : Set to ON the bits corresponding to the station numbers
14H
Station
information
Sets the type of connected remote station.
Default value : 20H (remote I/O station, occupies 1 station, station No. 1)
to 2EH (remote I/O station, occupies 1 station, station
No. 15)
Setting range : As shown below
20H (1st
station) to
2EH (15th
station)
Station type
Number of
occupied stations
Station No.
b15 b12 ~ b11 b8 ~ b7 b0
1: Occupies 1 station.
2: Occupies 2 stations.
3: Occupies 3 stations.
4: Occupies 4 stations.
1 to 15
(01H to 0FH)
0: Remote I/O station
1: Remote device station
~
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-5
7.3 Setting from Sequence Program
This section explains the parameter setting within the sequence program.
Parameters can be set using the following two methods:
1) Setting and operation using the buffer memory (Refer to subsection 7.3.1)
Use this method when starting up the system or when giving a change or addition to the
system after operation.
2) Parameter registration procedure to the EEPROM and operation based on parameters
registered in the EEPROM (Refer to subsection 7.3.2)
Registering parameters in advance to the EEPROM can save the parameter setting
program, and reduce the startup time.
[Caution]
The auxiliary relays in the non-keep area must be used as auxiliary relays (M) for parameter
setting programs.For the details, refer to 9.1.
7.3.1 Setting and operation using the buffer memory
K1 K4M20 HA K0 FROM
M0 PLS
M1 SET
MOV D0
MOV D1
MOV D2
K3 D0 H1 K0 TO
MOV D3
K1 D3 H6 K0 TO
MOV D4
K1 D4 H10 K0 TO
M0V D5
K1 D5 H14 K0 TO
MOV D13
K D13 H20 K0 TO
RST M1
M8000
Module error
M20 M35
RUN monitor
Module ready
M1
M1
M1
~
MOV D
Only when
required
Operation specification against
CPU down
Number of automatic return
modules
Number of retries
Number of connected modules
BFM#AHM35 to M20
Reserved station specification
Invalid station specification
Station information (set for
only connected modules)
M0
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-6
M40 SET
M3 SET
K1 D100 H0668 K0 FROM
M8002
Module
error
M20 M35
Initial pulse
Module
ready
M3
When data link startup by
buffer memory parameters
is completed abnormally
Refresh command
M2
M2 PLS
M46 SET
M46 RST
M3 RST
M46 RST
M3 RST
When data link startup by
buffer memory parameters
is completed normally
M26
M27
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-7
7.3.2 Parameter registration procedure to the EEPROM and operation based on parameters
registered in the EEPROM
1) Parameter registration procedure to the EEPROM
1.Write the parameter setting program shown below.
2.Turn ON the EEPROM registration command.
3.When registration of parameters to the EEPROM is completed, the system can be
operated using only the program for "2) Operation based on parameters registered in the
EEPROM."
Parameter setting program
K1 K4M20 HA K0 FROM
M0 PLS
M1 SET
MOV D0
MOV D1
MOV D2
K3 D0 H1 K0 TO
MOV D3
K1 D3 H6 K0 TO
MOV D4
K1 D4 H10 K0 TO
M0V D5
K1 D5 H14 K0 TO
MOV D13
K D13 H20 K0 TO
RST M1
M8000
Module error
M20 M35
RUN monitor
Module ready
M1
M1
M1
~
MOV D
Only when
required
Operation specification against
CPU down
Number of automatic return
modules
Number of retries
Number of connected modules
BFM#AHM35 to M20
Reserved station specification
Invalid station specification
Station information (set for
only connected modules)
M0
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-8
M40 SET
M8002
Initial pulse
Refresh command
M5 SET
K1 D101 H6B9 K0 FROM
Module
error
M20 M35
Module
ready
M5
When parameter
registration to EEPROM is
completed abnormally
M4
M4 PLS
M50 SET
M50 RST
M5 RST
M50 RST
M5 RST
When parameter
registration to EEPROM is
completed normally
M30
M31
Registration
command
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-9
2) Operation based on parameters registered in the EEPROM
This program operates the system based on parameter set values registered in the
EEPROM.
When the parameter set values have to be changed due to a change or addition to the
system, it is necessary to re-register parameters to the EEPROM.
Refer to 1) for the parameter registration method.
M40 SET
M1 SET
K1 D100 H0668 K0 FROM
M8002
Module
error
M20 M35
Initial pulse
Module
ready
M1
When data link startup by
EEPROM parameters is
completed abnormally
BFM#AHM35 to M20
M0
M0 PLS
M48 SET
M48 RST
M1 RST
M48 RST
M1 RST
When data link startup by
EEPROM parameters is
completed normally
M28
M29
M8000
RUN monitor
Refresh command
K1 K4M20 HA K0 FROM
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-10
7.3.3 Program example
The diagram below shows an example of program for parameter setting in the system
configuration shown below.
System configuration example
Program example
The following two types of program examples are shown below
1) Setting and operation using the buffer memory
2) Operation based on parameters registered in the EEPROM
[Caution]
The auxiliary relays in the non-keep area must be used as auxiliary relays (M) for parameter
setting programs. For the details, refer to 9.1.
1) Setting and operation using the buffer memory
Master
station
Remote I/O
station
(occupies 1 station)
Station No. 1
Remote I/O
station
(occupies 1 station)
Station No. 2
Remote
device station
(occupies 4
stations)
Station No. 3
Remote device station
(occupies 2 stations)
Station No. 7
Reserved station
(to be connected in the future)
Remote device station
(occupies 2 stations)
Station No. 9
Invalid station
K1 K4M20 HA K0 FROM
M0 PLS
M1 SET
MOV D0
MOV D1
MOV D2
K3 D0 H0001 K0 TO
MOV D3
K1 D3 H0006 K0 TO
MOV D4
K1 D4 H0010 K0 TO
MOV D5
K1 D5 H0014 K0 TO
M8000
Module
error
M20 M35
RUN monitor
Module
ready
M1
M1
Operation specification
against CPU down (stop)
Number of automatic return
modules (2 modules)
Number of retries (3 times)
Number of connected
modules (5 modules)
BFM#AHM35 to M20
Reserved station
specification
Invalid station
specification
M0
K5
K3
K2
K0
H0004
H0100
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-11
MOV
K5 D12 H0020 K0 TO
M1
Remote I/O station D12 H0101
M1 RST
M40 SET
M3 SET
K1 D100 H0668 K0 FROM
Module
error
M20 M35
Module
ready
M3
M2
M2 PLS
M46 SET
M46 RST
M3 RST
M46 RST
M3 RST
When data link startup by
buffer memory parameters
is completed normally
M26
M27
MOV D13 H0102
MOV D14 H1403
MOV D15 H1207
MOV D16 H1209
M8002
Initial pulse
When data link startup by
buffer memory parameters
is completed abnormally
Remote I/O station
Remote device station
(reserved station)
Remote device station
Remote device station
Refresh command
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-12
2) Operation based on parameters registered in the EEPROM
a) Parameter registration procedure to the EEPROM
1.Write the parameter setting program shown below.
2.Turn ON the EEPROM registration command.
3.When parameter registration to the EEPROM is completed, the system can be
operated using only the program for "a) Operation based on parameters registered in
the EEPROM".
The parameter setting program is not required
Parameter setting program
K1 K4M20 HA K0 FROM
M0 PLS
M1 SET
MOV D0
MOV D1
MOV D2
K3 D0 H0001 K0 TO
MOV D3
K1 D3 H0006 K0 TO
MOV D4
K1 D4 H0010 K0 TO
MOV D5
K1 D5 H0014 K0 TO
M8000
Module
error
M20 M35
RUN monitor
Module
ready
M1
M1
Operation specification
against CPU down (stop)
Number of automatic return
modules (2 modules)
Number of retries (3 times)
Number of connected
modules (5 modules)
BFM#AHM35 to M20
Reserved station
specification
Invalid station
specification
M0
K5
K3
K2
K0
H0004
H0100
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-13
MOV
K5 D12 H0020 K0 TO
M1
Remote I/O station D12 H0101
M1 RST
M40 SET
MOV D13 H0102
MOV D14 H1403
MOV D15 H1207
MOV D16 H1209
M8002
Initial pulse
Remote I/O station
Remote device station
(reserved station)
Remote device station
Remote device station
Refresh command
M5 SET
K1 D101 H06B9 K0 FROM
Module
error
M20 M35
Module
ready
M5
M4
M4 PLS
M50 SET
M50 RST
M5 RST
M50 RST
M5 RST
When parameter
registration to EEPROM is
completed normally
M30
M31
Registration
command
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
When parameter
registration to EEPROM is
completed abnormally
FX2N-16CCL-M CC-Link System Master Block Parameter Setting 7
7-14
b) Operation based on parameters registered in the EEPROM
This program operates the system based on parameter set values registered in the
EEPROM.
When the parameter set values have to be changed due to a change or addition to the
system, it is necessary to re-register parameters to the EEPROM.
Refer to a) for the parameter registration method.
M40 SET
M1 SET
K1 D100 H0668 K0 FROM
M8002
Module
error
M20 M35
Initial pulse
Module
ready
M1
When data link startup by
EEPROM parameters is
completed abnormally
BFM#AHM35 to M20
M0
M0 PLS
M48 SET
M48 RST
M1 RST
M48 RST
M1 RST
When data link startup by
EEPROM parameters is
completed normally
M28
M29
M8000
RUN monitor
Refresh command
K1 K4M20 HA K0 FROM
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
Data Link Procedure 8
8-1
8. Data Link Procedure
INSTALLATION PRECAUTIONS
Use the module in the environment for the general specification described in Chapter 4 of
this manual.
Do not use the PLC in a place with dust, soot, conductive dust, corrosive gas (Sea breeze,
Cl2, H2S, SO2, NO2 or combustible gas, place exposed to high temperature, condensation,
wind or rain or place with vibration or impact.
Using the module outside the range of the general specification or in a place above may
result in electrical shock, fire, malfunctions, or may damage the PLC.
When drilling screw holes or performing wiring, make sure that cutting chips, wire chips or
other foreign matter does not enter the ventilation window of the module.
Such matter may cause fire, failure or malfunction.
When the installation work is completed, remove the dust protection sheet from the
ventilation window of the PLC.
If the sheet remains attached, it may cause fire, failure or malfunction.
Securely connect extension cables to specified connectors.
Poor contact may cause malfunction.
WIRING PRECAUTIONS
Before beginning any installation or wiring work, make sure all phases of the power supply
have been shut down from the outside.
Incomplete shutdown of the power supply phases may cause electrical shock or damage in
the module.
Following an installation or wiring work, when turning on the power supply and operating the
PLC, make sure that the terminal cover provided as an accessory has been attached to the
module.
Non-attachment of the cover may cause electrical shock.
For the CC-Link system, use dedicated cables specified by the manufacturer.
The performance of the CC-Link system cannot be guaranteed with any cable other than
dedicated ones specified by the manufacturer.
For the maximum total extension length and the cable length between stations, observe the
specification described in Chapter 4.
With wiring outside the specification range, normal data transfer cannot be guaranteed.
Make sure to fix communication cables and power cables connected to the module by
placing them in the duct or clamping them.
Cables not placed in duct or not clamped may hang or shift, allowing them to be accidentally
pulled, which may result in malfunction or damage to the module and the cables.
When disconnecting a communication/power cable connected to the module, do not hold
the cable area.
For a cable with connector, hold the connector attached to the module.
For a cable connected to a terminal block, loosen screws of the terminal block, then
disconnect the cable.
If a cable is pulled while it is connected to a module, the module may malfunction or the
module and the cable may be damaged.
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-2
WIRING PRECAUTIONS
Perform Class D grounding (100 or less) with a wire of 2 mm
2
or more to the grounding
terminal in the PLC main unit. However, never perform common grounding with a high
voltage system.
Do not bundle control cables and communication cables with the main circuit and power
cables. Keep control cables and communication cables at least 100 mm away from the main
circuit and power cables.
Otherwise, electric noise may cause a malfunction.
PLC
Another
equipment
PLC
Another
equipment
PLC
Another
equipment
Common grounding
(allowed)
Common grounding
(not allowed)
Dedicated grounding
(best)
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-3
8.1 Data Link Procedure
The flowchart below shows the procedure for data link in the CC-Link system.
f[^NJnB
vO~O
Ep[^pvOij
EMpvOij
ejbgmFB
ieXgj
}X^jbgeXCb`B
i7.3C7.7Qj
EXCb`i7.7.1j
E[hXCb`i7.7.2j
E`xXCb`i7.7.3j
EXCb`i7.7.4j
jbg^Cv?
ejbgCC-LinkP[uB
}X^ubNPmFB
in[hEFAeXgj
V[PT}X^ubNB
Connect the PLC and the master block.
Module type?
Attach remote I/O modules and remote device
modules to the control panel and the machine.
Check in the master block single module whether
it operates normally (hardware test).
Connect each module with CC-Link cables.
Set switches in the master module.
Station No. setting switch (Section 8.6.1)
Mode setting switch (Section 8.6.2)
Transmission speed setting switch
(Section 8.6.3)
Condition setting switch (Section 8.6.4)
Set switches in the remote
modules.
Station No. setting switch
(Section 8.6.1)
Transmission speed setting
switch (Section 8.6.3)
Check the connection status of each module
(line test).
Programming (Chapters 10 to 12)
Program for parameter setting
Program for communication
Start data link.
Check the preset parameter information
(parameter verification test).
Refer to Section 8.8.
Remote I/O module
Remote device module Master block
Refer to Section 8.7.
Refer to Sections 8.4
and 8.5.
Refer to Section 8.3.
For installation, refer to
the supplied manual.
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-4
8.2 Name of Each Part and Settings
This section describes the name of each part of the master block, the external dimensions the
contents indicated by the LED indicators and the setting method of each switch.
RUN
ERR.
L ERR.
L RUN
MST
TEST1
TEST2
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
10
1
STATION
NO.
MODE
B RATE
1
3
2
4
156K
625K
2.5M
5M
10M
0
HLD
- -
ON OFF SW
1
2
3
- -
-
-
-
-
4
5
6
7
8
-
-
- -
-
-
CLR
FX2N-16CCL-M
0
1
2 3 4
5
6
7 8 9
87
6
5
4 3 2
1
0
9
87
6
5
4 3 2
1
0
9
0
1
234567
8
9
A B C D E F
1
2
3
4
5
6
7
8
ON
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
85(3.34)
9
0
(
3
.
5
)
87(3.43)
9(0.35)
FX2N-16CCL-M
2-f4.5
8
0
(
3
.
1
5
)
75(2.95)
M
I
T
S
U
B
I
S
H
I
1)
2)
3)
4)
5)
6)
8)
7)
9)
10)
11)
12)
Inside of top cover
2
4
+2
4
-
F
G
S
L
D
D
G
D
A
D
B
Dimensions: mm (inches)
MASS (weight): 0.4kg (0.88 lbs)
Accessories: Terminal registor
When a dedicated CC-Link cable is used:110 1/2W
(brown, brown and brown)
When a high-performance CC-Link cable is used: 130 1/2W
(brown, orange and brown)
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-5
Table 8.1:
Number Name Description
1) LED indicators 1
LED
name
Description
LED status
Normal Error
RUN
ON : Module is normal.
OFF : Watchdog time error has occurred.
ON OFF
ERR.
Indicates the communication status with the
stations set in parameter.
ON : Communication error has
occurred in all stations.
Flashing : Communication error has
occurred in some stations.
OFF
ON or
flashing
MST ON : Set as the master station ON OFF
TEST1 Test result indication
OFF except during
test
TEST2 Test result indication
L RUN
ON : Data link is being executed
(host station).
ON OFF
L ERR.
ON : Communication error has
occurred
(host station).
Flashing : The settings of the switches (4)
to (7) are changed while the
power is ON.
OFF
ON or
flashing
2) Power indictor POWER ON : 24V DC is supplied from the outside. ON OFF
3) LED indicators 2
E
R
R
O
R
SW ON : Switch setting error has occurred. OFF ON
M/S
ON : The master station is already present
in the same line.
OFF ON
PRM ON : Parameter setting error has occurred. OFF ON
TIME
ON : Data link watchdog timer is actuated
(error in all stations).
OFF ON
LINE
ON : The cable is broken or the
transmission route is affected by
noise, etc.
OFF ON
SD ON : Data is being transmitted. ON OFF
RD ON : Data is being received. ON OFF
4) Station number
setting switch
Sets the station number of the module. (Default setting at shipment: 00)
<Setting range>
00 (because the FX2N-16CCL-M is dedicated to the master station)
If "65" or larger number is set, the "SW" and "L ERR." LED indicators turn
ON.
RUN
ERR.
MST
TEST 1
TEST 2
L RUN
L ERR
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
STATION NO.
10
1
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-6
Number Name Description
5) Mode setting
switch
Sets the operation status of the module. (Default setting at shipment: 0)
Number Name Description
0 Online Sets connection to data link.
1 (Unusable)
2 Offline Sets disconnection from data link.
3 Line test 1 Refer to Section 8.7.1.
4 Line test 2 Refer to Section 8.7.2.
5
Parameter
verification test
Refer to Section 8.8.
6 Hardware test Refer to Section 8.3.
7 (Unusable) Setting error (The SW LED indicator turns ON.)
8 (Unusable) Cannot be set because it is already used inside.
9 (Unusable) Cannot be set because it is already used inside.
A (Unusable) Cannot be set because it is already used inside.
B (Unusable) Setting error (The SW LED indicator turns ON.)
C (Unusable) Setting error (The SW LED indicator turns ON.)
D (Unusable) Setting error (The SW LED indicator turns ON.)
E (Unusable) Setting error (The SW LED indicator turns ON.)
F (Unusable) Setting error (The SW LED indicator turns ON.)
6) Transmission
speed setting
switch
Sets the transmission speed of the module. (Default setting at shipment: 0)
Number Setting contents
0 156kbps
1 625kbps
2 2.5Mbps
3 5Mbps
4 10Mbps
5 Setting error (The SW and L ERR. LED indicators turn ON.)
6 Setting error (The SW and L ERR. LED indicators turn ON.)
7 Setting error (The SW and L ERR. LED indicators turn ON.)
8 Setting error (The SW and L ERR. LED indicators turn ON.)
9 Setting error (The SW and L ERR. LED indicators turn ON.)
MODE
1
2
3
456
7
8
9 0
A
B
C D
E
F
B RATE
0
2
1
3
4
156K
625K
2.5M
5M
10M
1
2
3
4
5
6
7
8
9
0
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-7
Number Name Description
7) Condition setting
switch
Sets the operation condition. (Default setting at shipment: All OFF)
Number Setting description
Switch status
ON OFF
SW1 (Unusable) Always OFF
SW2 (Unusable) Always OFF
SW3 (Unusable) Always OFF
SW4 Input data status in data link faulty station
Keep
(HLD)
Clear
(CLR)
SW5 (Unusable) Always OFF
SW6 (Unusable) Always OFF
SW7 (Unusable) Always OFF
SW8 (Unusable) Always OFF
8) Terminal block Connects dedicated CC-Link cables to enable data link.
For the connection method, refer to Section 8.4.
The terminals SLD and FG are connected inside.
M3.5 Screw
9) Terminal block Connects the power supply to operate the master block.
M3 Screw
10) Extension cable Connects the PLC.
11) Next step
extension
connector
Connects an extension equipment.
12) DIN rail mounting
groove
DIN46277: DIN rail mounting groove of 35 mm (1.38") in width
2
1
3
4

HLD

SW
6
5
7
8

ON

CLR

OFF ON
1
2
3
4
5
6
7
8
S
L
D
D
G
D
A
D
B
2
4
+
2
4
- F
G
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-8
8.3 Master Block Status Check (Hardware Test)
Check in the master block single module whether it operates normally.
Make sure to execute this hardware test before constructing the system.
Execute the test using the following procedure.
Connect a terminal resistor offered as an accessory
between the terminals DA and DB in the master block.
Set the mode setting switch in the master block to 6.
Turn off the power of the PLC and the master block,
then turn it on again.
OFF

ON
Approximately 4 seconds later, the test starts.
Start
The test result is indicated by the LED indicators in the master module.
The RUN LED turns OFF.
End
[When normal]
The LED indicators turn ON in the order "SW M/S PRM TIME".
SW
M/S
PRM
TIME

[When abnormal]
The table below shows the contents of each check item.
If an error occurs, replace the module.
SW is ON.
M/S is ON.
PRM is ON.
LED status
Module error
ROM error
RAM error
Description
Self-loop back check
ROM check
RAM check
Check item
Repeats.
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-9
8.4 Module Wiring with Dedicated CC-Link Cables
This section describes the connection method of dedicated CC-Link cables.
The cables can be connected without regard to the station number.
Make sure to connect a terminal resistor (offered as an accessory of the module) between
the terminals DA and DB in modules at both ends.
In the CC-Link system, the terminal resistor to be connected varies depending on the used
cable.
- When a dedicated CC-Link cable is used: 110 , 1/2 W (brown, brown and brown)
- When a dedicated high-performance CC-Link cable is used: 130 , 1/2 W (brown,
orange and brown)
The master module can be connected besides to the both ends.
Star connection is not allowed.
The figure below shows the connection method.
Important
Make sure to use only one type of cable (dedicated CC-Link cables OR dedicated
CC-Link high-performance cables).
If both types of cables are used together, normal data transmission cannot be
guaranteed.
Point
The shielded dedicated CC-Link cable should go through the terminals SLD and FG
in each module, and both ends should be grounded (Class D = 100 or less).
The terminals SLD and FG are connected each other inside the module.
DA
DB
DG
SLD
FG
DA
DB
DG
SLD
FG
DA
DB
DG
SLD
FG
Dedicated CC-Link cable Dedicated CC-Link cable
Master module Remote module Remote module
Terminal
resistor
Terminal
resistor
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-10
8.5 T-shaped Branch Connection Using Dedicated CC-Link Cables
This section describes the T-shaped branch connection using dedicated CC-Link cables.
8.5.1 System configuration with T-shaped branch connection
The figure below shows the system configuration with T-shaped branch connection.
Remote I/O station or
remote device station
Master station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Remote I/O station or
remote device station
Terminal
resistor
Terminal
resistor
(Branch line) (Branch line) (Branch line) (Branch line)
Up to 6 modules can be connected.
Up to 6 modules can be connected.
(Main line)
T-shaped branch
terminal block or
connector
* The number of branch lines is determined by each branch line length and the
total branch line length.
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-11
8.5.2 T-shaped branch communication specification list
The table below shows the communication specification in T-shaped branch connection.
For communication specification not shown in the table below, refer to Section 4.4.
Table 8.2:
Item Specification Remarks
Transmission speed 625kbps 156kbps 10, 5 and 2.5 Mbps are not available.
Maximum main line
length
100m 500m
The value indicates the cable length
between terminal resistors.
The cable length of T-shaped branch lines
(branch length) is not included.
Maximum branch line
length
8m
The value indicates the cable length per
branch line.
Total branch line
length
50m 200m
The value indicates the total length of all
branch lines.
Maximum number of
modules connected to
branch line
6 modules/branch line
The number of connected modules
conforms to the CC-Link specification.
Connection cable
Dedicated CC-Link cable
(Examples: FANC-SB, CSFV-SLAB,
100ZCLK-SB-20AWGX3C)
Dedicated high-performance CC-Link
cables (example: FANC-SBH) are not
available.
Cables produced by different
manufacturers are not available at the
same time.
(For manufacturers, refer to brochures.)
Terminal resistor
(connection method)
Connect a terminal resistor (110 ) packed
together with master module.
For the connection method, refer to Section
8.4.
T-shaped branch
terminal block/
connector
Terminal block: Commercial one
Connector:
Connector for FA sensor NECA4202
(IEC947-5-2) or its equivalent is
recommended.
(NECA: THE JAPAN ELECTRIC
CONTROL EQUIPMENT INDUSTRY
ASSOCIATION Standards)
When wiring cables to the main line, strip
as little of the insulation as possible.
Maximum main line
length, T-shaped
branch interval and
cable length between
modules
Dedicated CC-Link cable (with terminal resistor of 110 )
Transmission
speed
Maximum
main line
length
T-shaped
branch
interval
Cable length between
remote stations*1
Cable length between
master station and
adjacent station*2
625kbps 100m
No limit 30 cm or more 1 m or more
156kbps 500m
Master
station
Terminal
resistor
Terminal
resistor
R
R
R R
R
R R
R
R
R R R R
R
*2 *2
*2
*2
*1
*1 *1 *1 *1
*1
*1 *1
Maximum main line length (excluding branch line length)
: Indicates a remote I/O station or remote device station. R
(Branch line length: 8 m or less)
(Branch line length: 8 m or less)
*1
R
*1
*1
T-shaped branch interval
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-12
8.6 Switch Settings
This section describes the setting method of each switch in the modules.
8.6.1 Station number setting (master station, remote I/O stations and remote device stations)
This section describes the method to set the station number of the master station, remote I/O
stations and remote device stations.
1) Set the station numbers to be consecutive.
The station number can be set without regard to the connection order.
For a module occupying 2 or more stations, set the head station number.
Setting example: When setting the station numbers in the connection order
Point
Align the settings with the contents stored in the parameter information area "station
information (addresses 20H to 2EH)" in the buffer memory.
Table 8.3:
Station type Station number to be set
Master station 0 (fixed)
Remote I/O station
Remote device station
1 to 15
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1 Station No. 2
Remote
device station
(occupies 4
stations)
Station No. 3 Station No. 0
Remote I/O station
(occupies 1 station)
Remote
device station
(occupies 2
stations)
Station No. 7
Station No. 1 Station No. 2 Station No. 3 Station No. 4 Station No. 5 Station No. 6 Station No. 7 Station No. 8 Station No. 9 Station No. 0
Master
station
(fixed)

Remote I/O
station

Remote I/O
station

Remote device station

Remote device station

FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-13
2) Do not skip station numbers
The skipped station numbers are treated as "data link faulty stations" (which can be
checked in the link special register SW0080 or the buffer memory address 680H). However,
by setting such stations as reserved they are not treated as data link faulty stations.
Setting example 1: When one station number is skipped
3) Duplicate station numbers are not allowed.
If there are duplicate numbers, a loading status error occurs. (The error code is stored in
SW0069.)
Setting example: When one station number is duplicated
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1 Station No. 2
Remote
device station
(occupies 4
stations)
Station No. 4 Station No. 0
Remote I/O station
(occupies 1 station)
Remote
device station
(occupies 2
stations)
Station No. 8
Station No. 1 Station No. 2 Station No. 3 Station No. 4 Station No. 5 Station No. 6 Station No. 7 Station No. 8 Station No. 9 Station No. 0
Master
station
(fixed)

Remote I/O
station

Remote I/O
station

Remote device station

Remote device station

Data link faulty station
(It is not treated as faulty station if set as a reserved station.)
Master
station
Remote I/O station
(occupies 1 station)
Station No. 1 Station No. 2
Remote
device station
(occupies 4
stations)
Station No. 3 Station No. 0
Remote I/O station
(occupies 1 station)
Remote
device station
(occupies 2
stations)
Station No. 6
Station No. 1 Station No. 2 Station No. 3 Station No. 4 Station No. 5 Station No. 6 Station No. 7 Station No. 8 Station No. 9 Station No. 0
Master
station
(fixed)

Remote I/O
station

Remote I/O
station

Remote device station

Remote device station
Duplicate
station No.
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-14
8.6.2 Mode setting
When executing the data link, the normal setting is "0(online)".
8.6.3 Transmission speed setting
The available transmission speed varies depending on the total extension distance.
For the details, refer to Section 4.4.1.
8.6.4 Condition setting
The table below shows the setting method of the condition setting switch (DIP switch).
Point
Set the same transmission speed to all of the master station and remote stations.
If the setting is different even in one station, normal data link cannot be realized.
Table 8.4:
Number Description
Switch status
Setting
OFF ON
SW1 (Unusable) Always OFF
SW2 (Unusable) Always OFF
SW3 (Unusable) Always OFF
SW4
Input data status of
data link faulty
station (Section 5.8)
Clear Keep
OFF
Sets to OFF all of the input data from data
link faulty station.
ON
Keeps the input data from data link faulty
station in the status just before error.
SW5 (Unusable) Always OFF
SW6 (Unusable) Always OFF
SW7 (Unusable) Always OFF
SW8 (Unusable) Always OFF
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-15
8.7 Connection Status Check (Line Test)
After connecting all modules with dedicated CC-Link cables, execute the line test to check
whether connection is correctly established to execute data link with remote stations.
8.7.1 Check of connection status and communication status with remote stations (line test 1)
Check whether data link can be normally executed with all (15) remote stations.
Execute the test using the following procedure.
Point
Execute line test 2 when an error occurs in line test 1.
Accordingly, when no error is detected in the line test 1, there is no necessity to
execute line test 2.
Set the mode setting switch in the master block to 3.
Approximately 4 seconds later, the test starts.
Start
The test result is indicated by the LED indicators in the master block.
End
[When communication is normal in at least one station]
The LED indicators turn ON in the order "SW M/S PRM TIME".
The test result is stored in SW00B4.
However, because the test is executed to 15 stations, ignore the bits corresponding to
unconnected stations.
SW
M/S
PRM
TIME

Repeats until all

stations become faulty.
All stations are faulty or cable is broken.
Test cannot start (due to abnormality in
hardware, power OFF in all stations, etc.).
Cause
SW00B8

Error code storage area

PRM
None
Lighting LED
Turn off the power of the PLC and the master block,
then turn it on again.
OFF

ON
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-16
8.7.2 Check of communication status with specific remote station (line test 2)
Execute the line test 2 to check whether data link is normally executed with a specific remote
station.
There is no need to set parameters.
Execute the test using the following procedure.
Connect only a module to be tested to the master block.
Or turn on the power of only a module to be tested.
Set the station No. setting switch in the master block to
the station No. of the module to be tested.
Approximately 4 seconds later, the test starts.
Set the mode setting switch in the master block to 4.
The test result is indicated by the LED indicators in the master block.
[When normal]
The LED indicators turn ON in the order "SW M/S PRM TIME".
It is judged as normal when this repeats five times or more.
SW
M/S
PRM
TIME

Repeats.
[When abnormal]
Cable is broken or the corresponding
station has error.
Test transmission text is corrupt.
Test cannot start (due to abnormality in
hardware or power OFF in all stations).
Cause
SW00B8

Error code storage area

PRM
None
Lighting LED
Start
End
Turn off the power of the PLC and the master block, then
turn it on again.
OFF

ON
FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8
8-17
8.8 Parameter Check (Parameter Verification Test)
The contents of the parameters can be verified.
Execute the test using the following procedure.
Set the mode setting switch in the master block to 5.
The test can be executed even when cables are
connected to the master block.
Continued to the next page
The LED indicators light as shown below until the
setting of the mode setting switch is changed.
SW
M/S
PRM
TIME
Repeats.
Start
Turn off the power of the PLC and the master block,
then turn it on again.
OFF

ON
When the parameters are registered in the
EEPROM, set to ON the output of request for
data link startup by EEPROM parameters
(BFM#AH b8).
Register the parameters to the buffer memory,
then set to ON the output of request for data link
startup by buffer memory parameters
(BFM#AH b6).
or

FX2N-16CCL-M CC-Link System Master Block Data Link Procedure 8

8-18
The test result is indicated by the LED indicators in the master module.
By changing over the setting of the mode setting switch, the contents of the parameter corresponding
to each mode number are indicated by the LED indicators.
Continued from the previous page
Total number of stations
Parameter item Used LED indicators and contents
0
Mode setting
switch
Number of connected modules 1
2 Number of retries
10's digit : MST, TEST1, TEST2
1's digit : SW, M/S, PRM, TIME
MST
TEST1
TEST2

SW
M/S
PRM
TIME

40
20
10
8
4
2
1
MST
TEST1
TEST2

SW
M/S
PRM
TIME

In the case of 26
3 (Unusable)
4
5
Reserved station specification
*1
Invalid station specification
*1
6 Station type
*1*2
SW (OFF: No specification, ON: Specification given)
SW (OFF: No specification, ON: Specification given)
SW
M/S
7 Number of occupied stations
*1*2
SW
M/S
PRM
TIME
8 Station number
*1
10's digit : MST, TEST1, TEST2
1's digit : SW, M/S, PRM, TIME
MST
TEST1
TEST2

SW
M/S
PRM
TIME

40
20
10
8
4
2
1
MST
TEST1
TEST2

SW
M/S
PRM
TIME

In the case of 26
9 to F (Unusable)
*1 Set the station number of the module using the station number setting switch.
*2 For a module occupying 2 or more stations, the same contents are indicated for
as many as the number of occupied stations.
End
: 1 station
: 2 stations
: 3 stations
: 4 stations
: Remote I/O station
: Remote device station
Programming 9
9-1
9. Programming
9.1 Precautions in Programming
This section describes precautions in creating a program.
1) Word information of the remote device station is processed in FX2N-16CCL-M in one word
unit. Therefore, trying to transfer double word (32-bit data) between FX2N-16CCL-M and
PLC main unit may result in an error as upper word (16-bit data) and lower word (16-bit
data) may not be processed appropriately due to time lag in link-scanning.
2) Create a read program from the remote input RX (addresses E0H to FFH) after data link
startup.
Create a write program to the remote output RY (addresses 160H to 17FH) at the end of the
entire program.
3) Create such a program that read of received data and write of transmission data are
executed after the host station becomes the data link status (after the BFM#AH b1 turns
ON).
Parameter setting
Data link startup
Read from remote input (RX)
Write to remote output (RY)

M M M
M0 N0 MC
Program for communication
N0 MCR
Input of
module error
(BFM#AH b0)
Input of module
ready
(BFM#AH b15)
Input of data link
status in host station
(BFM#AH b1)
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-2
4) Create such a program that detects the data link status in remote I/O stations and remote
device stations and executes interlock.
Create a program for error handling.
5) The auxiliary relays in the non-keep area (example: relays marked with O) must be used
as auxiliary relays (M) for parameter setting programs.
M M M
K1 K4M0 H0680
Program for error handling
SW0080(Data link status in other stations)
K0 FROM
M0
Station No. 1 Program in normal status
M1
Station No. 2 Program in normal status
Module
error
Module
ready
Data link status in
host station
K1 K4M20 HA KO FROM
M0 PLS
M1 SET
M0V D0
M0V D1
M0V D2
K3 D0 H1 K0 T0
M0V D3
K1 D3 H6 K0 T0
M8000
Module
error
M20 M35
RUN monitor
Module
ready
M1
M0
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-3
9.2 Programming Procedure
This section describes the program creation procedure.
9.2.1 Communication between master station and remote I/O stations
The flowchart below shows the basic programming procedure for communication between the
master station and remote I/O stations.
For a program example, refer to Chapter 10.
Parameter setting
Refresh command
Data link startup by buffer memory
parameters
Parameter registration to EEPROM
Refresh command
Data link startup by EEPROM
parameters
Read from remote input (RX)
Control by read remote input information
ON/OFF control of remote output (RY)
Write to remote output (RY)
For operation based
on parameter set
values written in
buffer memory
BFM#AH b6
BFM#AH b10
BFM#AH b0
BFM#AH b8
Buffer memory addresses E0H to FDH
Buffer memory addresses 160H to 17DH
For operation based
on parameter set
values registered in
EEPROM
BFM#AH b0

FX2N-16CCL-M CC-Link System Master Block Programming 9

9-4
9.2.2 Communication between master station and remote device stations
The flowchart below shows the basic programming procedure for communication between the
master station and remote device stations.
For a program example, refer to Chapter 11.
Parameter setting
Refresh command
Data link startup by buffer memory
parameters
Parameter registration to EEPROM
Refresh command
Data link startup by EEPROM
parameters
Read from remote input (RX)
ON/OFF control of remote output (RY)
Write to remote output (RY)
For operation based
on parameter set
values written in
buffer memory
BFM#AH b6
BFM#AH b10
BFM#AH b0
BFM#AH b8
Buffer memory addresses 160H to 17DH
For operation based
on parameter set
values registered in
EEPROM
Read from remote register (RWr)
Control by read remote input (RX)
Control by read remote register (RWr)
data
Creation of data to be written to remote
register (RWw)
Write to remote register (RWw) Buffer memory addresses 1E0H to 21BH
Buffer memory addresses 2E0H to 31BH
Buffer memory addresses E0H to FDH
BFM#AH b0

FX2N-16CCL-M CC-Link System Master Block Programming 9

9-5
9.2.3 Communication in compound system
The basic programming procedure for the system where both remote I/O stations and remote
device stations are present is equivalent to that described in "9.2.2 Communication between
master station and remote device stations".
For a program example, refer to Chapter 12.
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-6
9.3 Link Special Relay/Register (SB/SW)
The data link status can be checked using the bit information (link special relay SB) and the
word information (link special register SW).
"SB" and "SW" represent the buffer memory information in the master block, and can be read
and written by the FROM/TO instruction.
- Link special relay (SB) :Buffer memory addresses 5E0H to 5FFH
- Link special register (SW) :Buffer memory addresses 600H to 7FFH
9.3.1 Link special relay (SB) list
For the correspondence with the buffer memory, refer to Section 4.6.10.
Table 9.1:
Number
Buffer memory
Name Description
Number Bit
SB0000 5E0H 0 Data link restart
Restarts the data link which was stopped by SB0002.
OFF : Does not give restart specification.
ON : Gives restart specification.
SB0002 5E0H 2 Data link stop
Stops the data link in the host station.
(Use SB0000 to restart the data link.)
If the master station sets this relay to ON, the entire
system stops.
OFF : Does not give stop specification.
ON : Gives stop specification.
SB0004 5E0H 4
Request for
temporary error
invalid station
Determines stations specified by SW0003 to
SW0004 as temporary error invalid stations.
OFF : Does not give the request.
ON : Gives the request.
SB0005 5E0H 5
Request for cancel
of temporary error
invalid station
Cancels the stations specified by SW0003 to
SW0004 from temporary error invalid stations.
OFF : Does not give the request.
ON : Gives the request.
SB0008 5E0H 8
Request for line
test
Executes the line test to the stations specified by
SW0008.
OFF : Does not give the request.
ON : Gives the request.
SB0009 5E0H 9
Request for
parameter
verification test
Reads the parameter information on the actual
system configuration, and sets it to the parameter
information area.
OFF : Does not give the request.
ON : Gives the request.
SB0020 5E2H 0 Module status
Indicates the buffer access status.
OFF : Does not give the request.
ON : Gives the request.
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-7
Number
Buffer memory
Name Description
Number Bit
SB0040 5E4H 0
Data link restart
acceptance status
Indicates the data link restart specification
acceptance status.
OFF : Not accepted
ON : Accepted
SB0041 5E4H 1
Data link restart
completion status
Indicates the data link restart specification
acceptance completion status.
OFF : Not completed
ON : Completed
SB0044 5E4H 4
Data link stop
acceptance status
Indicates the data link stop specification acceptance
status.
OFF : Not accepted
ON : Accepted
SB0045 5E4H 5
Data link stop
completion status
Indicates the data link stop specification acceptance
completion status.
OFF : Not completed
ON : Completed
SB0048 5E4H 8
Temporary error
invalid station
acceptance status
Indicates the temporary error invalid station request
acceptance status.
OFF : Not accepted
ON : Accepted
SB0049 5E4H 9
Temporary error
invalid station
completion status
Indicates the temporary error invalid station request
acceptance completion status.
OFF : Not completed
ON : Completed (Temporary error invalid stations
are determined.)
SB004A 5E4H 10
Temporary error
invalid station
cancel acceptance
status
Indicates the temporary error invalid station cancel
request acceptance status.
OFF : Not accepted
ON : Accepted
SB004B 5E4H 11
Temporary error
invalid station
cancel completion
status
Indicates the temporary error invalid station cancel
request acceptance completion status.
OFF : Not completed
ON : Completed (Cancel of temporary error invalid
stations is completed.)
SB004C 5E4H 12
Line test
acceptance status
Indicates the line test request acceptance status.
OFF : Not accepted
ON : Accepted
SB004D 5E4H 13
Line test
completion status
Indicates the line test completion status.
OFF : Not completed
ON : Completed
SB004E 5E4H 14
Parameter
verification test
acceptance status
Indicates the parameter verification test request
acceptance status.
OFF : Not accepted
ON : Accepted
SB004F 5E4H 15
Parameter
verification test
completion status
Indicates the parameter verification test completion
status.
OFF : Not completed
ON : Completed
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-8
Number
Buffer memory
Name Description
Number Bit
SB0050 5E5H 0
Offline test
execution status
Indicates the offline test execution status.
OFF : Not executed
ON : Being executed
SB0060 5E6H 0 Module mode
Indicates the setting status of the mode setting switch
in the module.
OFF : Online (0)
ON : Other than online (0)
SB0061 5E6H 1 Station type
Indicates the setting status of the station number
setting switch in the module.
OFF : Master station (No. 0)
ON : Setting error (The station number is not set to
0.)
SB0065 5E6H 5
Input status of data
link faulty station
Indicates the setting status of the condition setting
switch (DIP switch SW4) in the module.
OFF : Clear
ON : Keep
SB006A 5E6H 10
Switch setting
status
Indicates the switch setting status.
OFF : Normal
ON : Setting error (The error code is stored in
SW006A.)
SB006D 5E6H 13
Parameter setting
status
Indicates the parameter setting status.
OFF : Normal
ON : Setting error (The error code is stored in
SW0068.)
SB006E 5E6H 14
Operation status in
host station
Indicates the data link operation status in the host
station.
OFF : In progress
ON : Not executed
SB0073 5E7H 3
Status of operation
specification
against CPU down
Indicates the status of operation specification against
CPU down by parameter.
OFF : Stop
ON : Continue
SB0074 5E7H 4
Reserved station
specification status
Indicates the reserved station specification status by
parameter (SW0074).
OFF : Not specified
ON : Specified
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-9
Number
Buffer memory
Name Description
Number Bit
SB0075 5E7H 5
Error invalid station
specification status
Indicates the error invalid station specification status
by parameter (SW0078).
OFF : Not specified
ON : Specified
SB0076 5E7H 6
Temporary error
invalid station
specification status
Indicates the temporary error invalid station
specification status (SW007C).
OFF : Not specified
ON : Specified
SB0078 5E7H 8
Switch change
status in host
station
Detects change in the setting switches in the host
station during data link.
OFF : No change
ON : Change
SB0080 5E8H 0
Data link status in
other stations
Indicates the data link status with remote stations
(SW0080).
OFF : All stations are normal.
ON : Some stations are faulty.
SB0081 5E8H 1
Watchdog timer
error status in
other stations
Indicates the watchdog timer error occurrence status
in other stations (SW0084).
OFF : No error
ON : Error
SB0082 5E8H 2
Fuse blowout
status in other
stations
Indicates the fuse blowout occurrence status in other
stations (SW0088).
OFF : No error
ON : Error
SB0083 5E8H 3
Switch change
status in other
stations
Detects change in the setting switches in other
stations during data link (SW008C).
OFF : No change
ON : Change
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-10
9.3.2 Link special register (SW)
*1 Sets to ON only the bit corresponding to the head station number
Table 9.2:
Number
Buffer
memory
Name Description
SW0003 603H
Specification of
multiple temporary
error invalid stations
Selects whether or not to specify two or more temporary
error invalid stations.
00: Specifies two or more stations stored in SW0004.
01 to 15 : Specifies a single station whose station
number is 1 to 15.
* The number indicates the station number of a
temporary error invalid station.
SW0004 604H
Temporary error
invalid station
specification
*1
Specifies temporary error invalid stations.
0: Does not specify as temporary error invalid station.
1: Specifies as temporary error invalid station.
Numbers 1 to 15 above indicate station numbers
SW0008 608H
Line test station
setting
Sets the stations to be subject to the line test.
0 : Entire system (The line test will be executed to all
stations.)
01 to 15 : Station to be subject to the line test.
Default : 0
SW0020 620H Module status
Indicates the module status.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW0041 641H
Result of data link
restart
Stores the execution result of data link restart
specification by SB0000.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW0045 645H
Result of data link
stop
Stores the execution result of data link stop specification
by SB0002.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW0049 649H
Result of request for
temporary error
invalid stations
Stores the execution result of request for temporary error
invalid stations by SB0004.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW004B 64BH
Result of request for
cancel of temporary
error invalid stations
Stores the execution result of request for cancel of
temporary error invalid stations by SB0005.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW004D 64DH
Result of request for
line test
Stores the execution result of request for line test by
SB0008.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0004 15 14 13 ~ 4 3 2 1
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-11
*2 The loading status is checked only when link starts up, then stored.
Number
Buffer
memory
Name Description
SW004F 64FH
Result of request for
parameter
verification test
Indicates the execution result of request for parameter
verification test by SB0009.
0 : Normal:
Other than 0: Error code
SW0060 660H
Mode setting switch
status
Stores the setting status of the mode setting switch.
0 : Online
2 : Offline
3 : Line test 1
4 : Line test 2
5 : Parameter verification test
6 : Hardware test
1, 7 to F : Setting error
SW0061 661H
Station number
setting switch status
Stores the setting status of the station number setting
switch.
0 : Master station (Make sure to set the switch to 0)
Other than 0: Setting error
SW0062 662H
Condition setting
switch status
Stores the setting status of the condition setting switch
(DIP switch).
0: OFF
1: ON
SW0064 664H
Number of retries
setting status
Stores the setting status of the number of retries against
response error.
1 to 7 (times)
SW0065 665H
Number of automatic
return stations
setting status
Stores the setting status of the number of automatic
return modules during one link scan.
1 to 10 (modules)
SW0067 667H
Parameter
information
Stores the parameter information area to be used.
1: Buffer memory (data link startup by BFM#AH b6)
2: EEPROM (data link startup by BFM#AH b8)
SW0068 668H
Parameter status in
host station
Stores the parameter setting status.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW0069 669H
Loading status
*2
Stores station number overlap and consistency with
parameters in each module.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
* The details are stored in SW0098 and SW009C.
SW006A 66AH Switch setting status
Stores the switch setting status.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW006D 66DH
Maximum link scan
time
Stores the maximum value of the link scan time
(unit: 1 ms).
0 ~ 0
b15 b8 b7 b6 b5 b4 b3 b2 b1 b0
SW1
SW2
SW3
SW4
SW5
SW6
SW7
SW8
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-12
*1 Only the bit corresponding to the head station number is set to ON.
Number
Buffer
memory
Name Description
SW006E 66EH
Current link scan
time
Stores the current value of the link scan time (unit: 1 ms).
SW006F 66FH
Minimum link scan
time
Stores the minimum value of the link scan time (unit: 1 ms).
SW0070 670H
Total number of
stations
Stores the last station number set in parameter.
1 to 15 (stations)
SW0071 671H
Maximum
communication
station number
Stores the maximum station number (station number set
by the station number setting switch) in the data link.
1 to 15 (stations)
SW0072 672H
Number of
connected modules
Stores the number of modules (except reserved stations)
in the data link.
1 to 15 (modules)
SW0074 674H
Reserved station
specification status
*1
Stores the reserved station specification status.
0: Not specified as reserved station
1: Specified as reserved station
Numbers 1 to 15 above indicate station numbers
SW0078 678H
Error invalid station
specification status
*1
Stores the error invalid station specification status.
0: Not specified as error invalid station
1: Specified as error invalid station
Numbers 1 to 15 above indicate station numbers
SW007C 67CH
Temporary error
invalid station
specification status
*1
Stores the temporary error invalid station specification
status.
0: Not specified as temporary error invalid station
1: Specified as temporary error invalid station
Numbers 1 to 15 above indicate station numbers
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0074 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0078 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW007C 15 14 13 ~ 4 3 2 1
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-13
*1 Only the bit corresponding to the head station number is set to ON.
*3 Bits corresponding to as many as the number of occupied stations are set to ON.
Number
Buffer
memory
Name Description
SW0080 680H
Data link status in
other stations
*3
Stores the data link status in each station.
0: Normal
1: Data link error
Numbers 1 to 15 above indicate station numbers
SW0084 684H
Watchdog timer error
occurrence status in
other stations
*1
Stores the watchdog timer error occurrence status in each
station.
0: Normal
1: Watchdog timer error
Numbers 1 to 15 above indicate station numbers
SW0088 688H
Fuse blowout status
in other stations
*3
Stores the fuse blowout status in each station.
0: Normal
1: Fuse blowout error
Numbers 1 to 15 above indicate station numbers
SW008C 68CH
Switch change
status in other
stations
*1
Stores the switch change status in other stations during
data link.
0: No change
1: Change
Numbers 1 to 15 above indicate station numbers
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0080 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0084 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0088 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW008C 15 14 13 ~ 4 3 2 1
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-14
*3 Bits corresponding to as many as the number of occupied stations are set to ON.
*4 Only the bit corresponding to the head station number is set to ON.
The status is checked only when link starts up, and stored.
Number
Buffer
memory
Name Description
SW0098 698H
Station number
overlap status
*4
Stores the overlap status in which the head station
number of each module does not overlap.
0: Normal
1: Station number overlap (only the head station number)
Numbers 1 to 15 above indicate station numbers
SW009C 69CH
Loading/parameter
consistency status
*4
Stores the consistency with parameters.
0: Normal
1: Consistency error
Loading Parameter
Remote device station Remote I/O station
Numbers 1 to 15 above indicate station numbers
SW00B4 6B4H
Line test 1 result
*3
Stores the line test 1 result.
0: Normal
1: Error
Numbers 1 to 15 above indicate station numbers
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW0098 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW009C 15 14 13 ~ 4 3 2 1
b15 b14 b13 b12 ~ b3 b2 b1 b0
SW00B4 15 14 13 ~ 4 3 2 1
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-15
The timing at which the data in the link special registers (SW) is updated varies depending
on the register number as shown in the table below.
Number
Buffer
memory
Name Description
SW00B8 6B8H Line test 2 result
Stores the line test 2 result.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
SW00B9 6B9H
EEPROM
registration status
Stores the status of parameter registration to the
EEPROM.
0 : Normal
Other than 0: Error code (Refer to Section 13.3.)
Table 9.3:
Link special
register
Data update timing
Link special
register
Data update timing
SW0041
Updated independently without
regard to SB
SW0071
Updated independently without
regard to SB
(updated after each station is
stabilized)
SW0045 SW0072
SW0060 Updated when SB0060 changes SW0074 Updated when SB0074 changes
SW0061 Updated when SB0061 changes SW0078 Updated when SB0075 changes
SW0062
Updated independently without
regard to SB
SW0080 Updated when SB0080 changes
SW0067 SW0088
Updated independently without
regard to SB
SW0069 SW0098
Updated independently without
regard to SB
SW006A SW009C
SW006D SW00B4
SW006E SW00B8
SW006F SW00B9
SW0070
FX2N-16CCL-M CC-Link System Master Block Programming 9
9-16
MEMO
Communication between Master Station and Remote I/O Stations 10
10-1
10. Communication between Master Station and Remote I/O Stations
This chapter describes module setting, programming and operation check using a system
configuration example.
10.1 System Configuration
It is supposed that three remote I/O stations are connected in the system.
10.1.1 Setting of master station
The figure below shows the setting of the switches in the master station.
Terminal
resistor
Terminal
resistor
Remote I/O station
(station No. 1)
Remote I/O station
(station No. 2)
Remote I/O station
(station No. 3)
I/O module
AJ65BTB1-16DT
Output module
AJ65BTB1-16T
Input module
AJ65BTB1-16D
FX1N/FX2N/FX3U/FX2NC
Series PLC
CC-Link master block
FX2N-16CCL-M
RUN
ERR.
L ERR.
L RUN
MST
TEST1
TEST2
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
10
1
STATION
NO.
MODE
B RATE
1
3
2
4
156K
625K
2.5M
5M
10M
0
HLD
- -
ON OFF SW
1
2
3
- -
-
-
-
-
4
5
6
7
8
-
-
- -
-
-
CLR
FX2N-16CCL-M
0
1
2 3
4
5
6
7 8
9
87
6
5
4
3 2
1
0
9
87
6
5
4
3 2
1
0
9
0
1
2
3456
7
8
9
A
B C D E
F
1
2
3
4
5
6
7
8
ON
2
4
+2
4
-
F
G
S
L
D
D
G
D
A
D
B
0(10)
0(1)
Make sure to set the
master station to 00.
Station number setting switch
0 (online)
Mode setting switch
2 (2.5 Mbps)
Transmission speed setting switch
Condition setting switch
SW Setting Description
1 OFF
2 OFF
3 OFF
4 OFF Clear
5 OFF
6 OFF
7 OFF
8 OFF
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote I/O Stations 10
10-2
10.1.2 Setting of remote I/O station
The figure below shows the setting of the switches in a remote I/O station.
A B RATE
6
5
4
3
2
1
0
4
3
2
1
0
X1 X1 0
0 1 2 3 4 5 6 7 9 8 A B C D E F
RD SD L ERR. L RUN PW
J65BTB1 -1 6D
7
8
6
9
2
3
4
5
0
1
STAT ON NO.
2 (2.5Mbps)
Transmission speed setting switch
Module 10 1
AJ65BTB1-16D 0 1
AJ65BTB1-16T 0 2
AJ65BTB1-16DT 0 3
Station number setting switch.
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote I/O Stations 10
10-3
10.2 Creating a Program
10.2.1 Program for parameters
In the program below, data link automatically starts when the PLC starts to run.
[Caution]
The auxiliary relays in the non-keep area must be used as auxiliary relays (M) for parameter
setting programs.
For the details, refer to 9.1.
[Setting and operation using the buffer memory]
K1 K4M20 HA K0 FROM
M0 PLS
M1 SET
MOV D0
MOV D1
MOV D2
K3 D0 H0001 K0 TO
MOV D3
K1 D3 H0006 K0 TO
M8000
Module
error
M20 M35
RUN monitor
Module
ready
M1
Operation specification against CPU
down (stop)
Number of automatic return modules
(2 modules)
Number of retries (7 times)
Number of connected modules
(3 modules)
BFM#AHM35 to M20
M0
K3
K7
K2
K0
MOV
K3 D12 H0020 K0 TO
Remote I/O station (AJ65BTB1-16D) D12 H0101
M1 RST
MOV D13 H0102
MOV D14 H0103
Remote I/O station (AJ65BTB1-16T)
Remote I/O station (AJ65BTB1-16DT)
Station information
M1
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote I/O Stations 10
10-4
[Operation based on parameters registered in the EEPROM]
Refer to "7. Parameter Setting" for the parameter registration method to the EEPROM and the
operation method.
M40 SET
M3 SET
K1 D100 H0668 K0 FROM
Module
error
M20 M35
Module
ready
M3
M2
M2 PLS
M46 SET
M46 RST
M3 RST
M46 RST
M3 RST
When data link
startup by buffer
memory parameters
is completed normally
M26
M27
M8002
Initial pulse
When data link
startup by buffer
memory parameters
is completed
abnormally
Refresh command
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote I/O Stations 10
10-5
10.2.2 Program for communication
The figure below shows a program to control remote I/O stations.
It is supposed that the relationship among the PLC, the master station buffer memory and the
remote I/O stations is as shown below.
RX47~RX40
RX F ~ RX 0
RY4F~RY48
RY 2F ~ RY 20 M215 ~ M200
M247~M240
M115 ~ M100
RX4F~RX48
RY47~RY40
Remote I/O station (station No. 1)
AJ65BTB1-16D
PLC
M131 ~ M116
M147 ~ M132
M163 ~ M148
Master station
RX 1F ~ RX 10
RX 3F ~ RX 30
RX 5F ~ RX 50
RX 6F ~ RX 60
RX 7F ~ RX 70
RX 8F ~ RX 80
RX 9F ~ RX 90
Remote input (RX)
E0H
E1H
E2H
E3H
E4H
E5H
E6H
E7H
E8H
E9H
FDH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
Address
~
RY F ~ RY 0
RY 1F ~ RY 10
RY 3F ~ RY 30
RY 5F ~ RY 50
RY 6F ~ RY 60
RY 7F ~ RY 70
RY 8F ~ RY 80
RY 9F ~ RY 90
17DH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
~
160H
161H
162H
163H
164H
165H
166H
167H
168H
169H
M231 ~ M216
M263 ~ M248
M239~M232
Remote output (RY) Address
FROM
TO
X0F ~ X00
Only RX47 to RX40 are used.
Remote I/O station (station No. 2)
AJ65BTB1-16T
Y0F ~ Y00
Remote I/O station (station No. 3)
AJ65BTB1-16DT
X7~X0
YF~Y8
Only RY4F to
RY48 are used.
M171~M164 M179~M172
M187 ~ M180
TO
FROM
RX 2F ~ RX 20
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote I/O Stations 10
10-6
[Program to control remote I/O stations]
When the inputs X000 to
X017 in the PLC are set
to ON, the outputs Y0F to
Y00 in the AJ65BTB1-
16T turn ON.
For
communication
with the
AJ65BTB1-16D
(station No. 1)
Module
error
Data link is being executed in the
master station.
M8000
M20 M35
Module
ready
M21
Data link status in
host station
M500 N0 MC
N0 M500
RUN
monitor
K1 K4M400 H0680 K0 FROM
M400
M550
M401
M551
M402
M552
M8000
RUN
monitor
K1 K4M100 H00E0 K0 FROM
Y000
M100
Y017
M115
M200
X000
M215
X017
Y020
M164
Y027
M171
M240
X020
M247
X027
M8000
RUN
monitor
K3 K4M200 H0162 K0 TO
N0 MCR
For
communication
with the
AJ65BTB1-16DT
(station No. 3)
Reads the data link status in each
station (SW0080).
There is an error in the remote I/O
station No. 1.
There is an error in the remote I/O
station No. 2.
There is an error in the remote I/O
station No. 3.
Reads from the remote input (RX).
When the inputs X0F to
X00 in the AJ65BTB1-
16D turn ON, the outputs
Y000 to Y017 in the PLC
turn ON.
Read
(FROM)
Write
(TO)
When the inputs X07 to
X00 in the AJ65BTB1-
16DT turn ON, the
outputs Y020 to Y027 in
the PLC turn ON.
When the inputs X020 to
X027 in the PLC are set
to ON, the outputs Y0F to
Y08 in the AJ65BTB1-
16DT turn ON.
Read
(FROM)
Write
(TO)
Writes to remote output (RY).
~
~
~
~
For
communication
with the
AJ65BTB1-16T
(station No. 2)
K1 K2M164 H00E4 K0 FROM
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote I/O Stations 10
10-7
10.3 Execution of Data Link
Turn on the power of the remote I/O stations first, turn on the power of the master station, then
start the data link.
10.3.1 Confirmation of operation by LED indication
The figures below show the LED indication status in the master station and the remote I/O
stations while the data link is normally proceeding.
1) LED indication in the master station
Make sure that the LED indication status is as shown below.
2) LED indication in the remote I/O station
Make sure that the LED indication status is as shown below.
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
FX2N-16CCL-M
The module is normal.
The module is set as the master
station.
Data link is normally proceeding.
Data is being transmitted.
Data is being received.
AJ65BTB1-16D
PW L RUN SD RD L ERR.
24V DC is
supplied.
Data link is normally
proceeding.
Data is being
transmitted.
Data is being
received.
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote I/O Stations 10
10-8
10.3.2 Confirmation of operation by program
Using a sequence program, make sure that data link is normally proceeding.
For example, when the input X00 in the remote I/O station AJ65BTB1-16D (station No. 1) is
set to ON, the output Y000 in the master station turns ON.
When the input X000 in the master station is set to ON, the output Y00 in the remote I/O
station AJ65BTB1-16T (station No. 2) turns ON.
Terminal
resistor
Terminal
resistor
Remote I/O station
(station No. 1)
Remote I/O station
(station No. 2)
Remote I/O station
(station No. 3)
I/O module
AJ65BTB1-16DT
Output module
AJ65BTB1-16T
Input module
AJ65BTB1-16D
CC-Link master block
FX2N-16CCL-M
X000
ON
Y000
ON

X00
ON

Y00
ON

FX1N/FX2N/FX3U/FX2NC
Series PLC
Communication between Master Station and Remote Device Stations 11
11-1
11. Communication between Master Station and Remote Device Stations
This chapter describes module setting, programming and operation check using a system
configuration example.
11.1 System Configuration
It is supposed that two remote device stations are connected in the system.
11.1.1 Setting of master station
The figure below shows the setting of the switches in the master station.
Terminal
resistor
Terminal
resistor
Remote device station
(station No. 1)
Remote device station
(station No. 3)
A/D conversion module
AJ65BT-64AD
CC-Link master block
FX2N-16CCL-M
Occupies
2 stations.
Occupies
3 stations.
FX0N/FX1N/FX2N/FX3U/
FX2NC Series PLC
CC-Link interface block
FX2N-32CCL
FX1N/FX2N/FX3U/FX2NC
Series PLC
RUN
ERR.
L ERR.
L RUN
MST
TEST1
TEST2
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
10
1
STATION
NO.
MODE
B RATE
1
3
2
4
156K
625K
2.5M
5M
10M
0
HLD
- -
ON OFF SW
1
2
3
- -
-
-
-
-
4
5
6
7
8
-
-
- -
-
-
CLR
FX2N-16CCL-M
0
1
2 3
4
5
6
7 8
9
87
6
5
4
3 2
1
0
9
87
6
5
4
3 2
1
0
9
0
1
2
3456
7
8
9
A
B C D E
F
1
2
3
4
5
6
7
8
ON
2
4
+2
4
-
F
G
S
L
D
D
G
D
A
D
B
0(10)
0(1)
Make sure to set the
master station to 00.
Station number setting switch
0 (online)
Mode setting switch
2 (2.5 Mbps)
Transmission speed setting switch
Condition setting switch
SW Setting Description
1 OFF
2 OFF
3 OFF
4 OFF Clear
5 OFF
6 OFF
7 OFF
8 OFF
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-2
11.1.2 Setting of remote device station
The figure below shows the setting of the switches in a remote device station.
A
B RATE
6
5
4
3
2
1
0
4
3
2
1
0
X1 X10
RD
SD
L ERR.
L RUN
PW
J 65BT-64AD
7
8
6
9
2
3
4
5
0
1
STATION NO.
CH
4
3
2
1
0
OFFSET GAIN RESET
RUN
2(2.5Mbps)
Transmission speed setting switch Station number setting switch.
0(10)
1(1)
0
5
1
2
3
4
9
8
7
6
0
5
1
2
3
4
9
8
7
6
0
5
1
2
3
4
9
8
7
6
0
5
1
2
3
4
9
8
7
6
2
4
+
2
4
-
F
G
D
B
S
L
D
D
A
STATION
NO.
POWER
B RATE
0 1st.
1 2st.
2 3st.
3 4st.
0 156K
1 625K
2 2.5M
3 5M
4 10M
OCCUPY
STATION
32CCL
x10 x1
D
B
D
A
D
G
LRUNLERRRDSD
0 (10)
3 (1)
Station number setting switch
2 (3st.)
Number of occupied stations
2 (2.5Mbps)
Transmission speed setting switch
FX2N-32CCL
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-3
11.2 Creating a Program
11.2.1 Program for parameters
In the program below, data link automatically starts when the PLC starts to run.
[Caution]
The auxiliary relays in the non-keep area must be used as auxiliary relays (M) for parameter
setting programs.
For the details, refer to 9.1.
[Setting and operation using the buffer memory]
K1 K4M20 HA K0 FROM
M0 PLS
M1 SET
MOV D0
MOV D1
MOV D2
K3 D0 H0001 K0 TO
MOV D3
K1 D3 H0006 K0 TO
M8000
Module
error
M20 M35
RUN monitor
Module
ready
M1
Operation specification
against CPU down (stop)
Number of automatic return
modules (2 modules)
Number of retries (7 times)
Number of connected
modules (2 modules)
BFM#AHM35 to M20
M0
K2
K7
K2
K0
MOV
K2 D12 H0020 K0 TO
Remote device station
(AJ65BT-64AD)
D12 H1201
M1 RST
MOV D13 H1303 Remote device station
(FX2N-32CCL)
Station information
M1
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-4
[Operation based on parameters registered in the EEPROM]
Refer to "7. Parameter Setting" for the parameter registration method to the EEPROM and the
operation method.
M40 SET
M3 SET
K1 D100 H0668 K0 FROM
Module
error
M20 M35
Module
ready
M3
M2
M2 PLS
M46 SET
M46 RST
M3 RST
M46 RST
M3 RST
When data link
startup by buffer
memory parameters
is completed normally
M26
M27
M8002
Initial pulse
When data link
startup by buffer
memory parameters
is completed
abnormally
Refresh command
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-5
11.2.2 Program for communication
The figure below shows a program to control remote device stations.
It is supposed that the relationship among the PLC, the master station buffer memory and the
remote device stations is as shown below.
For the details of remote device stations, refer to the users manual of each module.
[Remote input (RX) and remote output (RY)]
Remote device station (station No. 1)
AJ65BT-64AD PLC
M115 ~ M100
M131 ~ M116
M163 ~ M148
Master station
RX F ~ RX 0
RX 1F ~ RX 10
RX 3F ~ RX 30
RX 4F ~ RX 40
RX 5F ~ RX 50
RX 6F ~ RX 60
RX 7F ~ RX 70
RX 8F ~ RX 80
RX 9F ~ RX 90
Remote input (RX)
E0H
E1H
E2H
E3H
E4H
E5H
E6H
E7H
E8H
E9H
FDH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
Address
~
RY F ~ RY 0
RY 1F ~ RY 10
RY 2F ~ RY 20
RY 3F ~ RY 30
RY 5F ~ RY 50
RY 6F ~ RY 60
RY 7F ~ RY 70
RY 8F ~ RY 80
RY 9F ~ RY 90
17DH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
~
160H
161H
162H
163H
164H
165H
166H
167H
168H
169H
Remote output (RY) Address
FROM
TO
RX0F ~ RX00
M147 ~ M132
M195 ~ M180
M179 ~ M164
M227 ~ M212
(System area)
M211 ~ M196
RX 2F ~ RX 20
RY 4F ~ RY 40
M315 ~ M300
M331 ~ M316
M363 ~ M348
M347 ~ M332
M395 ~ M380
M379 ~ M364
M427 ~ M412
(System area)
M411 ~ M396
RX1F ~ RX10
Remote input (RX)
RY0F ~ RY00
RY1F ~ RY10
Remote output (RY)
Remote device station (station No. 3)
FX2N-32CCL
RX0F ~ RX00
RX1F ~ RX10
Remote input (RX)
RX2F ~ RX20
RX3F ~ RX30
RX4F ~ RX40
RX5F ~ RX50
(System area)
RY0F ~ RY00
RY1F ~ RY10
Remote output (RY)
RY2F ~ RY20
RY3F ~ RY30
RY4F ~ RY40
RY5F ~ RY50
(System area)
FROM
TO
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-6
[Remote register (RWw, RWr)]
Averaging processing
specification
CH1 average time/
number of times
CH2 average time/
number of times
CH3 average time/
number of times
CH4 average time/
number of times
A/D conversion enable/
disable specification
RWw 7
Data type
CH1 digital output value
CH2 digital output value
CH3 digital output value
CH4 digital output value
RWr 7
Error code
RWr 5
RWr 6
Remote device station (station No. 1)
AJ65BT-64AD PLC
D100
Master station
Remote register (RWw)
1E0H
1E1H
1E2H
1E3H
1E4H
1E5H
1E6H
1E7H
1E8H
1E9H
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
Address
TO
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
D111
D112
D113
D114
D115
D116
D117
D118
D119
D200
D201
D202
D203
D204
D205
D206
D207
D208
D209
D210
D211
D212
D213
D214
D215
D216
D217
D218
D219
RWw 8
RWw 9
RWw A
RWw B
RWw C
RWw D
RWw E
RWw F
RWw 11
RWw 12
RWw 13
RWw 10
1EAH
1EBH
1ECH
1EDH
1EEH
1EFH
1F0H
1F1H
1F2H
1F3H
Remote register (RWr)
2E0H
2E1H
2E2H
2E3H
2E4H
2E5H
2E6H
2E7H
2E8H
2E9H
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
RWr 8
RWr 9
RWr A
RWr B
RWr C
RWr D
RWr E
RWr F
RWr 11
RWr 12
RWr 13
RWr 10
2EAH
2EBH
2ECH
2EDH
2EEH
2EFH
2F0H
2F1H
2F2H
2F3H
FROM
Averaging processing
specification
CH1 average time/
number of times
Remote register (RWw)
CH2 average time/
number of times
CH3 average time/
number of times
CH4 average time/
number of times
A/D conversion enable/
disable specification
(Unused)
Data type
CH1 digital output value
Remote register (RWr)
CH2 digital output value
CH3 digital output value
CH4 digital output value
(Unused)
Error code
(Unused)
(Unused)
Remote device station (station No. 3)
FX2N-32CCL
Remote register (RWw)
RWw 0
RWw 1
RWw 2
RWw 3
RWw 4
RWw 5
RWw 6
RWw 7
RWw 9
RWw A
RWw B
RWw 8
Remote register (RWr)
RWr 0
RWr 1
RWr 2
RWr 3
RWr 4
RWr 5
RWr 6
RWr 7
RWr 9
RWr A
RWr B
RWr 8
TO
FROM
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-7
[Program to control remote device stations]
Module
error
Reads the data link status in
remote device station (SW0080).
M20 M35
Module
ready
M21
Data link status in
host station
K1 K4M501 H0680 K0 FROM
P10 CALL
Normal link (station No. 1)
M501
Link error (station No. 1)
Y030
P20 CALL
Normal link (station No. 3)
M503
Link error (station No. 3)
Y031
FEND
K2 K4M100 H00E0 K0 FROM
M8000
M124
D100 H0202 MOV
(initial data processing request flag: RX18)
D102 K60 MOV
D105 H0001 MOV
D106 H0003 MOV
K1 D100 H01E0 K0 TO
K0 TO K1 D102 H01E2
K0 TO K2 D105 H01E5
M324 SET
M325 SET
M324 RST
M325 RST
M125
Data link is being executed in
the AJ65BT-64AD.
There is an error in data link in
the AJ65BT-64AD.
There is an error in data link in
the FX2N-32CCL.
Data link is being executed in
the FX2N-32CCL.
Reads from the remote input (RX) in
the AJ65BT-64AD.
Averaging processing specification
(CH2 time averaging)
CH2 average time/number of times
(60 ms)
Data type
(-2048 to 2047)
A/D conversion enable/disable
specification
(CH1 and CH2: Conversion enable)
Request for initial data settings
(RY18)
Initial data processing completed
(RY19)
Program for
communication
with the
AJ65BTB1-64AD
Initial settings
P10
(initial data setting completion flag: RX19)
M124
M501
M503
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-8
Reads from remote input.
E9H~E4H(RX9F~RX40)
M227~M132
CH1 digital output value
M100
K1 D200 H02E0 K0 FROM
K1 D201
M101
M127
(CH1 A/D conversion completion flag: RX0)
(CH2 A/D conversion completion flag: RX1)
H02E1 K0 FROM CH2 digital output value
Error code K1 D204 H02E4 K0 FROM
X010
M126 (error status flag: RX1A)
Request for error reset (RY1A) M326
Writes to remote output (RY) in
the AJ65BT-64AD.
K2 K4M300 H0160 K0 TO
M8000
RUN
monitor
SRET
K4M132 H00E4 K0 FROM
M8000
K6 K4M332 H0164 K0 TO
K12 D208 H02E8 K0 FROM
K12 D108 H01E8 K0 TO
Writes to remote output.
M427~M332
169H~164H(RY9F~RY40)
Reads from remote register (RWr).
2F3H~2E8H(RWr13~RWr8)
D219~D208
Writes to remote register (RWw).
D119~D108
1F3H~1E8H(RWw13~RWw8)
SRET
Remote ready
(RX1B)
Reads digital
values.
Reads error code.
Program for
communication with
the FX2N-32CCL
P20
K6
RUN
monitor
Program for
confirming
operation of the
FX2N-32CCL
Y000
M132
M332
X000
When RX00 in the FX2N-32CCL
(station No. 3) turns ON, Y000 in the
PLC turns ON.
FX2N-32CCL
(RX00)
When X000 in the PLC turns ON,
RY00 in the FX2N-32CCL turns ON.
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-9
11.3 Execution of Data Link
Turn on the power of the remote device stations first, turn on the power of the master station,
then start the data link.
11.3.1 Confirmation of operation by LED indication
The figures below show the LED indication status in the master station and the remote device
stations while the data link is proceeding normally.
1) LED indication in the master station
Make sure that the LED indication status is as shown below.
2) LED indication in the remote device station
Make sure that the LED indication status is as shown below.
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
FX2N-16CCL-M
The module is normal.
The module is set as the master
station.
Data link is normally proceeding.
Data is being transmitted.
Data is being received.
AJ65BT-64AD
PW
L RUN
SD
RD
L ERR.
RUN
POWER
FX2N-32CCL
LRUN LERR RD SD
5V DC is supplied from the PLC.
Data link is normally proceeding.
Data is being transmitted.
Data is being received.
24V DC is supplied.
The module is normal.
Data link is normally
proceeding.
Data is being transmitted.
Data is being received.
FX2N-16CCL-M CC-Link System Master Block Communication between Master Station and Remote Device Stations 11
11-10
11.3.2 Confirmation of operation by program
Using a sequence program, make sure that data link is proceeding normally.
The digital values converted by the AJ65BT-64AD are stored in D200 (CH1 digital value)
and D201 (CH2 digital value).
When X000 in the PLC turns ON, RY00 in the FX2N-32CCL turns ON.
When RX00 in the FX2N-32CCL turns ON, Y000 (M132) in the PLC turns ON.
Point
A program for communication is required also in the PLC connected to the FX2N-
32CCL.
(Refer to the FX2N-32CCL Users Manual.)
Terminal
resistor
Terminal
resistor
Remote device station
(station No. 1)
Remote device station
(station No. 3)
A/D conversion module
AJ65BT-64AD
CC-Link master block
FX2N-16CCL-M
CC-Link interface block
FX2N-32CCL
X000
ON

ON

RX00

RY00

A/D conversion by AJ65BT-64AD

D200: CH1 digital value
D201: CH2 digital value

Occupies
2 stations.
Occupies
3 stations.
FX1N/FX2N/FX3U/FX2NC
Series PLC
FX0N/FX1N/FX2N/FX3U/
FX2NC Series PLC
Communication in Compound System 12
12-1
12. Communication in Compound System
This chapter describes module setting, programming and operation confirmation in the system
in which remote I/O station and remote device station exist together using a system
configuration example.
12.1 System configuration
It is supposed that one remote I/O station and one remote device station are connected in the
system.
12.1.1 Setting of master station
The figure below shows the setting of the switches in the master station.
Terminal
resistor
Terminal
resistor
Remote I/O station
(station No. 1)
Remote device station
(station No. 2)
Input module
AJ65BTB1-16D
CC-Link master block
FX2N-16CCL-M
CC-Link interface block
FX2N-32CCL
Occupies
1 stations.
Occupies
3 stations.
FX1N/FX2N/FX3U/FX2NC
Series PLC
FX0N/FX1N/FX2N/FX3U/
FX2NC Series PLC
RUN
ERR.
L ERR.
L RUN
MST
TEST1
TEST2
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
10
1
STATION
NO.
MODE
B RATE
1
3
2
4
156K
625K
2.5M
5M
10M
0
HLD
- -
ON OFF SW
1
2
3
- -
-
-
-
-
4
5
6
7
8
-
-
- -
-
-
CLR
FX2N-16CCL-M
0
1
2 3
4
5
6
7 8
9
87
6
5
4
3 2
1
0
9
87
6
5
4
3 2
1
0
9
0
1
2
3456
7
8
9
A
B C D E
F
1
2
3
4
5
6
7
8
ON
2
4
+2
4
-
F
G
S
L
D
D
G
D
A
D
B
0(10)
0(1)
Make sure to set the
master station to 00.
Station number setting switch
0 (online)
Mode setting switch
2 (2.5 Mbps)
Transmission speed setting switch
Condition setting switch
SW Setting Description
1 OFF
2 OFF
3 OFF
4 OFF Clear
5 OFF
6 OFF
7 OFF
8 OFF
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-2
12.1.2 Setting of remote I/O station
The figure below shows the setting of the switches in the remote I/O station.
12.1.3 Setting of remote device station
The figure below shows the setting of the switches in the remote device station.
A B RATE
6
5
4
3
2
1
0
4
3
2
1
0
X1 X1 0
0 1 2 3 4 5 6 7 9 8 A B C D E F
RD SD L ERR. L RUN PW
J65BTB1 -1 6D
7
8
6
9
2
3
4
5
0
1
STAT ON NO.
2 (2.5Mbps)
Transmission speed setting switch Station number setting switch.
0 (10)
1 (1)
0
5
1
2
3
4
9
8
7
6
0
5
1
2
3
4
9
8
7
6
0
5
1
2
3
4
9
8
7
6
0
5
1
2
3
4
9
8
7
6
2
4
+
2
4
-
F
G
D
B
S
L
D
D
A
STATION
NO.
POWER
B RATE
0 1st.
1 2st.
2 3st.
3 4st.
0 156K
1 625K
2 2.5M
3 5M
4 10M
OCCUPY
STATION
32CCL
x10 x1
D
B
D
A
D
G
LRUNLERRRDSD
0 (10)
2 (1)
Station number setting switch
2 (3 st.)
Number of occupied stations
2 (2.5Mbps)
Transmission speed setting switch
FX2N-32CCL
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-3
12.2 Creating a Program
12.2.1 Program for parameters
In the program below, data link automatically starts when the PLC starts to run.
[Caution]
The auxiliary relays in the non-keep area must be used as auxiliary relays (M) for parameter
setting programs.
For the details, refer to 9.1.
[Setting and operation using the buffer memory]
K1 K4M20 HA K0 FROM
M0 PLS
M1 SET
MOV D0
MOV D1
MOV D2
K3 D0 H0001 K0 TO
MOV D3
K1 D3 H0006 K0 TO
M8000
Module
error
M20 M35
RUN monitor
Module
ready
M1
Operation specification
against CPU down (stop)
Number of automatic return
modules (2 modules)
Number of retries (7 times)
Number of connected
modules (2 modules)
BFM#AHM35 to M20
M0
K2
K7
K2
K0
MOV
K2 D12 H0020 K0 TO
Remote I/O station
(AJ65BTB1-16D)
D12 H0101
M1 RST
MOV D13 H1302 Remote device station
(FX2N-32CCL)
Station information
M1
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-4
[Operation based on parameters registered in the EEPROM]
Refer to "7. Parameter Setting" for the parameter registration method to the EEPROM and the
operation method.
M40 SET
M3 SET
K1 D100 H0668 K0 FROM
Module
error
M20 M35
Module
ready
M3
M2
M2 PLS
M46 SET
M46 RST
M3 RST
M46 RST
M3 RST
When data link
startup by buffer
memory parameters
is completed normally
M26
M27
M8002
Initial pulse
When data link
startup by buffer
memory parameters
is completed
abnormally
Refresh command
K1 K4M40 HA K0 TO
M8000
RUN monitor
M55 to M40BFM#AH
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-5
12.2.2 Program for communication
The figure below shows a program to control the remote I/O station and the remote device
station.
It is supposed that the relationship among the PLC, the master station buffer memory, the
remote I/O station and the remote device station is as shown below.
For the details of remote device station, refer to the users manual of the module.
[Remote input (RX) and remote output (RY)]
M115 ~ M100
M163 ~ M148
RX F ~ RX 0
RX 3F ~ RX 30
RX 4F ~ RX 40
RX 5F ~ RX 50
RX 6F ~ RX 60
RX 7F ~ RX 70
RY 2F ~ RY 20
RY 3F ~ RY 30
RY 5F ~ RY 50
RY 6F ~ RY 60
RY 7F ~ RY 70
X0F ~ X00
M147 ~ M132
M195 ~ M180
M179 ~ M164
M227 ~ M212
(System area)
M211 ~ M196
RX 2F ~ RX 20
RY 4F ~ RY 40
M363 ~ M348
M347 ~ M332
M395 ~ M380
M379 ~ M364
M427 ~ M412
(System area)
M411 ~ M396
RX0F ~ RX00
RX1F ~ RX10
RX2F ~ RX20
RX3F ~ RX30
RX4F ~ RX40
RX5F ~ RX50
(System area)
RY0F ~ RY00
RY1F ~ RY10
RY2F ~ RY20
RY3F ~ RY30
RY4F ~ RY40
RY5F ~ RY50
(System area)
Remote I/O station (station No. 1)
AJ65BTB1-16D PLC
M131 ~ M116
Master station
RX 1F ~ RX 10
RX 8F ~ RX 80
RX 9F ~ RX 90
Remote input (RX)
E0H
E1H
E2H
E3H
E4H
E5H
E6H
E7H
E8H
E9H
FDH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
Address
~
RY F ~ RY 0
RY 1F ~ RY 10
RY 8F ~ RY 80
RY 9F ~ RY 90
17DH
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
~
160H
161H
162H
163H
164H
165H
166H
167H
168H
169H
Remote output (RY) Address
FROM
Remote device station (station No. 2)
FX2N-32CCL
Remote input (RX)
Remote output (RY)
FROM
TO
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-6
[Remote register (RWw, RWr)
D100
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
D111
RWr 7
RWr 5
RWr 6
RWr 0
RWr 1
RWr 2
RWr 3
RWr 4
RWw 7
RWw 1
RWw 2
RWw 3
RWw 4
RWw 5
RWw 6
RWw 0
PLC Master station
Remote register (RWw)
1E0H
1E1H
1E2H
1E3H
1E4H
1E5H
1E6H
1E7H
1E8H
1E9H
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
Address
TO
D112
D113
D114
D115
D116
D117
D118
D119
D200
D201
D202
D203
D204
D205
D206
D207
D208
D209
D210
D211
D212
D213
D214
D215
D216
D217
D218
D219
RWw 8
RWw 9
RWw A
RWw B
RWw C
RWw D
RWw E
RWw F
RWw 11
RWw 12
RWw 13
RWw 10
1EAH
1EBH
1ECH
1EDH
1EEH
1EFH
1F0H
1F1H
1F2H
1F3H
Remote register (RWr)
2E0H
2E1H
2E2H
2E3H
2E4H
2E5H
2E6H
2E7H
2E8H
2E9H
For station
No. 1
For station
No. 2
For station
No. 3
For station
No. 4
For station
No. 5
RWr 8
RWr 9
RWr A
RWr B
RWr C
RWr D
RWr E
RWr F
RWr 11
RWr 12
RWr 13
RWr 10
2EAH
2EBH
2ECH
2EDH
2EEH
2EFH
2F0H
2F1H
2F2H
2F3H
FROM
Remote device station (station No. 2)
FX2N-32CCL
Remote register (RWw)
RWw 0
RWw 1
RWw 2
RWw 3
RWw 4
RWw 5
RWw 6
RWw 7
RWw 9
RWw A
RWw B
RWw 8
Remote register (RWr)
RWr 0
RWr 1
RWr 2
RWr 3
RWr 4
RWr 5
RWr 6
RWr 7
RWr 9
RWr A
RWr B
RWr 8
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-7
[Program to control remote I/O stations and remote device stations]
Module
error
Reads the data link status in remote
station (SW0080).
M20 M35
Module
ready
M21
Data link
status in
host station
K1 K4M501 H0680 K0 FROM
P10 CALL
Normal link (station No. 1)
M501
Link error (station No. 1)
Y030
P20 CALL
Normal link (station No. 2)
M502
Link error (station No. 2)
Y031
FEND
Data link is being executed in the
AJ65BTB1-16D.
There is an error in data link in the
AJ65BTB1-16D.
There is an error in data link in the
FX2N-32CCL.
Data link is being executed in the
FX2N-32CCL.
K1 K4M100 H00E0 K0 FROM
M8000
Program for
communication with
remote I/O station
P10
Y000
M100
Y017
M115
When inputs X00 to X0F in the
AJ65BTB1-16D turn ON, outputs
Y000 to Y017 in the PLC turn ON.
~
SRET
Reads from remote inputs
E7H to E2H (RX7F to RX20).
M212 to M132
SRET
K4M132 H00E2 K0 FROM
M8000
K6 K4M332 H0162 K0 TO
K12 D200 H02E4 K0 FROM
K12 D100 H01E4 K0 TO
Writes to remote outputs
M427 to M332.
167H to 162H (RY7F to RY20)
Reads from remote registers (RWr)
2EFH to 2E4H (RWrF to RWr4).
D211 to D200
Writes to remote registers (RWw)
D111 to D100. 1EFH to 1E4H
(RWwF to RWw4)
Program for
communication with
the FX2N-32CCL
P20
K6
RUN
monitor
M501
M502
Program for
confirming
operation of the
FX2N-32CCL
Y020
M132
M332
X000
When RX00 in the FX2N-32CCL
(station No. 2) turns ON, Y020 in the
PLC turns ON
FX2N-32CCL
(RX00)
When X000 in the PLC turns ON,
RY00 in the FX2N-32CCL turns ON.
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-8
12.3 Execution of Data Link
Turn on the power of the modules in the order "remote I/O station, remote device station
master station", then start the data link.
12.3.1 Confirmation of operation by LED indication
The figures below show the LED indication status in the master station, the remote I/O station
and the remote device station while the data link is normally proceeding.
1) LED indication in the master station
Make sure that the LED indication status is as shown below.
2) LED indication in the remote I/O station
Make sure that the LED indication status is as shown below.
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
POWER
SW
M/S
PRM
TIME
LINE
SD
RD
E
R
R
O
R
FX2N-16CCL-M
The module is normal.
The module is set as the master
station.
Data link is normally proceeding.
Data is being transmitted.
Data is being received.
AJ65BTB1-16D
PW L RUN SD RD L ERR.
24V DC is
supplied.
Data link is normally
proceeding.
Data is being
transmitted.
Data is being
received.
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-9
3) LED indication in the remote device station
Make sure that the LED indication status is as shown below.
12.3.2 Confirmation of operation by program
Using a sequence program, make sure that data link is normally proceeding.
When X00 in the remote I/O station is set to ON, Y000 in the PLC turns ON.
When X000 in the PLC turns ON, RY00 in the FX2N-32CCL turns ON.
When RX00 in the FX2N-32CCL turns ON, Y020 (M132) in the PLC turns ON.
.
Point
A program for communication is required also in the PLC connected to the FX2N-
32CCL.
(Refer to the FX2N-32CCL Users Manual.)
POWER
FX2N-32CCL
LRUN LERR RD SD
5V DC is supplied from the PLC.
Data link is normally proceeding.
Data is being transmitted.
Data is being received.
Terminal
resistor
Terminal
resistor
Remote I/O station
(station No. 1)
Remote device station
(station No. 2)
Input module
AJ65BTB1-16D
CC-Link master block
FX2N-16CCL-M
CC-Link interface block
FX2N-32CCL
X000
ON

ON

RX00

RY00

Y000 Y020
X00
ON

Occupies
1 stations.
Occupies
3 stations.
FX1N/FX2N/FX3U/FX2NC
Series PLC
FX0N/FX1N/FX2N/FX3U/
FX2NC Series PLC
FX2N-16CCL-M CC-Link System Master Block Communication in Compound System 12
12-10
MEMO
Troubleshooting 13
13-1
13. Troubleshooting
STARTING AND MAINTENANCE PRECAUTIONS
Do not touch the terminals while the power is supplied.
Otherwise, electrical shock or malfunction may be caused.
Turn off the power first, then clean the module or tightening the screws.
Cleaning or tightening in the power ON status may cause electrical shock.
Before executing program changes, forcible output, RUN operation or STOP operation,
thoroughly read the manual and sufficiently confirm safety.
Incorrect operation may damage the module or cause an accident.
STARTING AND MAINTENANCE PRECAUTIONS
Do not disassemble or rebuild the module.
It may cause failures, malfunction or fire.
Before connecting or disconnecting a connection cable such as an extension cable, turn off
the power.
Otherwise, the module may fail or malfunction.
DISPOSAL PRECAUTIONS
When disposing of the module, handle it as industrial waste.
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-2
13.1 Verification when Trouble Occurs
The table below shows the details to be checked and corrective actions for each trouble
occurrence.
Table 13.1:
Trouble description Details to be checked Confirmation method
Data link is disabled
in the entire system.
Are any cables broken?
Check the cable status visually or by the line
test.
Are terminal resistors properly connected to
stations at the both ends?
Connect terminal resistors offered as
accessories of the master module to stations
at the both ends.
Has an error occurred in the master station?
Check the error code in the PLC, and take
the corrective action.
Are parameters set in the master station?
Confirm the contents of the parameters.
Confirm the contents of the parameters in
link special registers.
(Refer to Subsection 9.3.2)
Is the write request for data link startup
(BFM#AH b6 or b8) ON?
Confirm the sequence program.
Has an error occurred in the master station?
Confirm the following:
Parameter status in the host station
(SW0068)
Switch setting status (SW006A)
Loading status (SW0069)
Flashing of the ERR LED in the master
station (Section 13.2.)
Inputs from a remote
I/O station cannot be
received.
Is the remote I/O station executing data link?
Check the following:
LED indication in the module
Communication status in the master
station with other stations (SW0080)
Is data read from the correct address of
remote input RX (buffer memory)?
Confirm the sequence program.
Is the station specified as reserved one? Confirm the contents of the parameters.
Does the station number overlap? Confirm the station number
Is the connection/setting beyond the
specification of the master station?
Confirm the contents of the BFM#1DH.
(Section 4.6.5)
Outputs are disabled
in a remote I/O
station.
Is the remote I/O station executing data link?
Check the following:
LED indication in the module
Communication status in the master
station with other stations (SW0080 to
SW0083)
Is the refresh command output (BFM#AH b0)
ON in the master station?
Confirm the sequence program.
Is data written to the correct address of
remote output RY (buffer memory)?
Confirm the sequence program.
Is the station specified as reserved one? Confirm the contents of the parameters.
Does the station number overlap? Confirm the station number
Is the connection/setting beyond the
specification of the master station?
Confirm the contents of the BFM#1DH.
(Section 4.6.5)
Things to do after checking the communication status with other stations (SW0080)
1) Read the contents of the BFM#1DH, and check whether access outside the allowable range is not
executed. (Refer to Section 4.6.5.)
2) Check whether the cable wiring is correct.
3) Check whether terminal resistors are correctly connected to modules at the both ends.
4) Check whether communication is enabled when the transmission speed is made slower.
5) Check whether the settings are consistent between the parameters and the startup station.
6) Check whether the station numbers overlap.
7) Replace a faulty module with a correctly operating one, and check whether the single module is
defective.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-3
Trouble description Details to be checked Confirmation method
Remote input (RX) in
a remote device
station cannot be
received.
Is the remote device station executing data
link?
Check the following:
LED indication in the module
Communication status in the master
station with other stations (SW0080)
Is data read from the correct address of
remote input RX (buffer memory)?
Confirm the sequence program.
Is the station specified as reserved one? Confirm the contents of the parameters.
Does the station number overlap? Confirm the station number
Is the connection/setting beyond the
specification of the master station?
Confirm the contents of the BFM#1DH.
(Section 4.6.5)
Remote output
(RY) in a remote
device station
cannot be set to
ON or OFF.
Is the remote device station executing data
link?
Check the following:
LED indication in the module
Communication status in the master
station with other stations (SW0080)
Is the refresh command output (BFM#AF b0)
ON in the master station?
Confirm the sequence program.
Is data written to the correct address of
remote output RY (buffer memory)?
Confirm the sequence program.
Is the station specified as reserved one? Confirm the contents of the parameters.
Does the station number overlap? Confirm the station number
Is the connection/setting beyond the
specification of the master station?
Confirm the contents of the BFM#1DH.
(Section 4.6.5)
Data in remote
register (RWr) in a
remote device
station cannot be
received.
Is the remote device station executing data
link?
Check the following:
LED indication in the module
Communication status in the master
station with other stations (SW0080)
Is data read from the correct address of
remote register RWr (buffer memory)?
Confirm the sequence program.
Is the station specified as reserved one? Confirm the contents of the parameters.
Does the station number overlap? Confirm the station number
Is the connection/setting beyond the
specification of the master station?
Confirm the contents of the BFM#1DH.
(Section 4.6.5)
Data cannot be
written to remote
register (RWw) in a
remote device
station.
Is the remote device station executing data
link?
Check the following:
LED indication in the module
Communication status in the master
station with other stations (SW0080)
Is data written to the correct address of
remote register RWw (buffer memory)?
Confirm the sequence program.
Is the station specified as reserved one? Confirm the contents of the parameters.
Does the station number overlap? Confirm the station number
Is the connection/setting beyond the
specification of the master station?
Confirm the contents of the BFM#1DH.
(Section 4.6.5)
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-4
Trouble description Details to be checked Confirmation method
Data link cannot
be stopped.
Is the data link stop (SB0002) ON? Confirm the sequence program.
Has an error occurred?
Check the data link stop result
(SW0045).
Data link cannot
be restarted.
Is the data link stop (SB0000) ON? Confirm the sequence program.
Has an error occurred?
Check the data link restart result
(SW0041).
Parameters cannot
be registered to
the EEPROM.
Is the write request for parameter
registration to EEPROM (BFM# AH b10)
ON?
Confirm the sequence program.
Has an error occurred?
Check the EEPROM registration status
(SW00B9).
A remote station
cannot start up.
Are the settings consistent between the
station information (parameter) and the
remote station?
Confirm the contents of the parameters.
Does the station number overlap with
another module?
Check the station number setting
switch.
Faulty stations
cannot be
detected.
Are stations specified as error invalid
ones?
Confirm the contents of the parameters.
Does the station number overlap? Check the station number
Faulty stations
occur depending
on the
transmission
speed.
Can faulty stations be detected by the
communication status in other stations
(SW0080)?
Check the switch settings in the
faulty station.
Check whether the cable wiring is
correct.
Check whether the cable shield is
grounded.
Is normal communication established
when the transmission speed is slowed
(to 156 kbps, for example)?
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-5
13.2 Troubleshooting when ERR LED is Flashing in Master Station
ERR LED is flashing in
master station.
Correct parameter setting or
loading system configuration.
Is parameter setting
consistent with loading
system configuration?
Is link special
register SW0080
(data link in other
stations) in master
station ON?
Check module corresponding
to ON bit in SW0098.
Is station No. switch
correctly set?
Corresponding module is
defective.
Y
Is link special
register SW0098
(station No. overlap)
ON in master
station?
Y
Y
Y
N
Master station is defective.
N
N
Check module corresponding
to ON bit in SW0080.
Is power turned on?
Is POWER LED lit?
Y
Is RD LED lit?
Y
Set station No. switch
correctly.
N
Turn off power, then turn it on
again.
Turn on power.
N
Is supplied voltage
inside specified
range?
Set supplied voltage inside
specified range.
Corresponding module is
defective.
Are communication
cables correctly wired?
Corresponding module is
defective.
N
Y
Correct wiring of
communication cables.
N
N
Check on master station side
Check on slave station side
Y
Y
To the next page To the next page To the next page
N
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-6
From the
previous page
From the
previous page
Is station No. switch
correctly set (without
overlapping another
station)?
Is L RUN LED lit?
Is SD LED lit (flashing)?
Y
Is SD LED lit (flashing)?
Is transmission speed
correctly set?
Set transmission speed
correctly.
Turn off power, then turn it on
again. Or turn on reset switch.
Are communication
cables correctly
wired?*1
N
N
Correct wiring of
communication cables.
N
Y
Corresponding
module is
defective.
Is station No. switch
correctly set (without
overlapping another
station)?
Y
Corresponding module is
defective.
(transmission speed switch)
Corresponding module is
defective.
(station No. switch)
Y
Corresponding module is
defective.
(station No. switch)
Turn off power, then turn it on
again. Or turn on reset switch.
N
Set station No.
correctly.
Turn off power, then turn it on
again. Or turn on reset switch.
N
Set station No.
correctly.
Completed
*1 Check for short circuit, inverse connection and wire breakage. Check the terminal resistors, the FG connection,
the total extension distance and the station-to-station distance.
N
Y
Y
N
Y
From the
previous page
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-7
13.3 Error Codes
The table below shows the error codes stored in the link special register (SW).
Table 13.2:
Error
code
(hex.)
Description Cause of error (details) Corrective action
B110
Message receive
disabled
A line error has occurred. Check the line.
B111
Message data
receive order error
A line error has occurred. Check the line.
B112
Message data
length error
A line error has occurred. Check the line.
B113
Message data
identification error
A line error has occurred. Check the line.
B114 Link error A line error has occurred. Check the line.
B115 Link error A line error has occurred. Check the line.
B116 Head bit error A line error has occurred. Check the line.
B301
Request for
processing during
link stop
The request for line test was given
while link was stopped.
Execute the line test while link is
executed.
B302
Specified station
number setting
error
When the request for temporary error
invalid station or the request for
cancel of temporary error invalid
station was given, the specified
station number was beyond the
maximum communication station
number
Specify a station number not more
than the maximum communication
station number
B303
Specified station
number no-setting
error
When the request for temporary error
invalid station or the request for
cancel of temporary error invalid
station was given, the station number
was not specified.
Specify a station number
(SW0003, SW0004).
B306
Specified station
setting error
When the request for temporary error
invalid station or the request for
cancel of temporary error invalid
station was given, a head station was
not specified.
Specify a head station in giving the
request for temporary error invalid
station or the request for cancel of
temporary error invalid station.
B307
Data link error in
all stations
When the following request was
given, there was data link error in all
stations.
SB0000 (data link restart)
SB0002 (data link stop)
Wait until the data link becomes
normal, then give the request again.
B308
Station number
setting error
The station number of a slave station
is not set inside the range from 1 to
64. (In the FX2N-16CCL-M, available
slave station numbers are from 1 to
15.)
Set a station number inside the
specification range (1 to 15) of the FX
Series master station.
B309
Station number
overlap error
In connected modules, a station
number overlaps (including the
number of occupied stations,
excluding overlap of a head station
number)
Check the station numbers of the
modules.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-8
B30A
Loading/
parameter
consistency error
The station type is different between
the module and the parameter.
Set the parameter correctly.
B30B
Loading/
parameter
consistency error
The loading status is not consistent
with the network parameters.
Align the loading status with the
network parameters.
B30D
Temporary error
invalid station
specification error
Before link starts up, temporary error
invalid stations are specified.
Start up the data link first, then
specify temporary error invalid
stations.
B384
Station number
setting error
(parameter)
The station number in the station
information (addresses 20H to 2EH)
(parameter) is not set inside the
range from 1H to 40H.
Set a station number inside the
specification range (1H to 10H) of the
FX Series master station.
B385
Total number of
modules setting
error (parameter)
The total number of occupied stations
in the station information (addresses
20H to 2EH) (parameter) is beyond 64.
Set the parameter inside the
specification range (15 or less) of the
FX Series master station.
B386
Number of
occupied stations
setting error
(parameter)
The number of occupied stations in
the station information (addresses
20H to 2EH) (parameter) is set to 0 for
every station.
Set the number of occupied stations
inside the range from 1 to 4.
B387
Unusable area
write error
Data was written to the unusable area
(unused) in the buffer memory.
Do not write to the unusable area
(unused) in the buffer memory.
B388
Station type
setting error
The station type in the station
information (addresses 20H to 2EH)
(parameter) is not set inside the
range from 0 to 2.
Set 0 or 1.
B389
Unusable area
write error
Data was written to the unusable area
(unused) in the buffer memory.
Do not write to the unusable area
(unused) in the buffer memory.
B38D
Error invalid
station
specification error
(parameter)
In the invalid station specification
(address 14H) (parameter), a station
number other than a module head
station number or a station number
not set in the parameter is set.
Example of station number other than
head station number:
For a module occupying 4 stations
(station Nos. 5 to 8), a bit not
corresponding to the station No. 5 is
set to ON.
Set a module head station number
Do not set a station number which is
not set in the parameter.
Table 13.2:
Error
code
(hex.)
Description Cause of error (details) Corrective action
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-9
Error
code
(hex.)
Description Cause of error (details) Corrective action
B391
Number of retries
setting error
(parameter)
The number of retries (address 2H)
(parameter) is not set inside the
range from 1 to 7.
Set a value inside the range from 1 to
7.
B392
Operation against
CPU down
specification error
(parameter)
The operation specification against
CPU down (address 6H) (parameter)
is not set to 0 or 1.
Set 0 or 1.
B394
Number of
automatic return
modules setting
error (parameter)
The number of automatic return
modules (address 3H) (parameter) is
not set inside the range from 1 to 10.
Set a value inside the range from 1 to
10.
B396
Station number
overlap error
(parameter)
In the station information (addresses
20H to 2EH) (parameter), one station
number is specified twice or more.
Use each station number only once.
B397
Station information
setting error
(parameter)
The station information (addresses
20H to 2EH) (parameter) does not
satisfy the system configuration
condition.
Set the parameters to satisfy the
condition.
B398
Number of
occupied stations
setting error
(parameter)
In the station information (addresses
20H to 2EH) (parameter), the number
of occupied stations is not set inside
the range from 1 to 4.
Set a value inside the range from 1 to
4.
B399
Number of
connected
modules setting
error (parameter)
The number of connected modules
(address 1H) (parameter) is not set
inside the range from 1 to 64.
Set a value inside the specification
range (1 to 15) of the FX Series
master station.
B39B
Reserved station
specification error
(parameter)
In the reserved station specification
(parameter), all stations are set as
reserved ones.
Confirm the reserved station
specification (parameter).
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-10
Error
code
(hex.)
Description Cause of error (details) Corrective action
B901 EEPROM error
When the write request for parameter
registration to EEPROM (BFM#AH
b10) was executed, the EEPROM
was defective or the specified number
of times of write (10,000 times) is
exceeded.
Replace the module.
B902
Data link startup
by EEPROM
parameters error
Though parameters were not
registered in the EEPROM, the write
request for data link startup by
EEPROM parameters (BFM#AH b8)
was executed.
Register parameters by executing the
request for parameter registration to
EEPROM (BFM#AH b10).
BA19
Error in
corresponding
station
In the line test 2, communication was
disabled in the tested station.
Check the cables and the
corresponding station.
BA1B Error in all stations
In the line test 1, communication was
disabled in all stations.
Check the cables.
BBC2
Station number
setting error
(switch)
The station number setting switch in
the module is not set inside the range
from 0 to 64.
Set a value inside the specification
range (0 to 15) of the FX Series
master station.
BBC3
Transmission
speed setting error
(switch)
The transmission speed setting
switch in the module is not set inside
the range from 0 to 4.
Set a value inside the range from 0 to
4.
BBC5
Master station
overlap error
The master station already exists.
Review the station number setting
switch.
BBC6
Mode change
error
An attempt was made to change the
mode from 0 or 2 to test by executing
the write request for module reset
(BFM#AH b4).
Change the mode by resetting the
PLC.
BBC7 Module error Module is defective. Replace the module.
BFFE
CPU watchdog
timer timeout
The CPU watchdog timer is timed out.
Check the operation of the target
station.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-11
13.4 LED Indication Status
This section shows the LED indication status in each station in each data link (system) status.
Use this section as reference of troubleshooting.
13.4.1 When data link is normal
The RUN, MST, L RUN, SD and RD LED indicators are ON.
13.4.2 When a cable is broken
Data link is disabled in all stations.
The L RUN LED indicator is OFF in stations after the breakage position.
FX2N-16CCL-M
Master
station
PLC
Terminal
resistor
Remote I/O
station
Stabilized power
supply (24V DC)
PW L RUN SD RD L ERR.
Remote device
station
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.

E
R
R
O
R
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD

RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
FX2N-16CCL-M
SW
M/S
PRM
TIME
LINE
SD
RD
Remote I/O
station
Remote device
station

Wire
breakage
E
R
R
O
R
Master
station
PLC
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-12
13.4.3 When a cable is short-circuited
Data link is disabled in all stations.
The L RUN LED indicator is OFF in all stations except the master station. However, the short-
circuited point cannot be detected from the LED indication.
13.4.4 When link is stopped in the master station
Data link is disabled in all stations.
The L RUN LED indicator is OFF in all stations.
FX2N-16CCL-M
Remote I/O
station
Remote device
station
E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.

FX2N-16CCL-M
Remote I/O
station
Remote device
station

E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-13
13.4.5 When power supply to a remote I/O station is turned off
Data link continues excluding the remote I/O station.
The ERR LED indicator is flashing in the master station.
13.4.6 When power supply to a remote device station is turned off
Data link continues excluding the remote device station.
The ERR LED indicator is flashing in the master station.
FX2N-16CCL-M
Remote I/O
station
Remote device
station
Because data link is
disabled in one station
(It is OFF if the remote
I/O station is set as an
error invalid station in
the parameter.)

E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M
Remote I/O
station
Remote device
station
Because data link is
disabled in one station
(It is OFF if the remote
I/O station is set as an
error invalid station in
the parameter.)

E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-14
13.4.7 When a station number overlaps
The example below shows a case in which a station number overlaps in a remote I/O station
and a remote device station.
Because a skipped number (number without a slave station) is made in the system due to
station number overlap, the ERR LED indicator is flashing in the master station.
13.4.8 When the transmission speed is incorrectly set
The example below shows a case in which the transmission speed setting is wrong in a remote
device station.
The L RUN LED indicator is OFF in a remote device station in which the transmission speed
setting is wrong.
FX2N-16CCL-M
Remote I/O
station
Remote device
station

E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M
Remote I/O
station
Remote device
station

E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-15
13.4.9 When the switch setting is changed during data link
The example below shows a case in which the switch setting is changed in a remote I/O
station.
The L ERR LED indicator is flashing in a remote I/O station in which the switch setting is
changed. However, data link can continue.
When the switch setting is returned to the previous status, the L ERR LED indictor turns off.
13.4.10 When data link is started with a switch set outside the allowable range
The example below shows a case in which a switch was set outside the allowable range in a
remote device station, then data link is started up.
In the remote device station, the L RUN LED indicator is OFF, and the L ERR LED indicator is
ON.
FX2N-16CCL-M
Remote I/O
station
Remote device
station

E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M
Remote I/O
station
Remote device
station

E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M CC-Link System Master Block Troubleshooting 13
13-16
13.4.11 When a remote I/O station is not set in the parameter (and set as a reserved station)
Data link is completely disabled in the remote I/O station, and no error occurs.
The L RUN and SD LED indicators are OFF in the remote I/O station.
13.4.12 When a remote device station is not set in the parameter (and set as a reserved station)
Data link is completely disabled in the remote device station, and no error occurs.
The L RUN and SD LED indicators are OFF in the remote device station.
FX2N-16CCL-M
Remote I/O
station
Remote device
station
No error
occurs.
E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
FX2N-16CCL-M
Remote I/O
station
Remote device
station
No error
occurs.
E
R
R
O
R
Master
station
PLC
RUN
ERR.
MST
TEST1
TEST2
L RUN
L ERR.
SW
M/S
PRM
TIME
LINE
SD
RD
: Indicates the ON status.
: Indicates the OFF status.
: Indicates the flashing status.
: Indicates the ON, OFF or flashing status.
PW L RUN SD RD L ERR.
Terminal
resistor
Stabilized power
supply (24V DC)
Stabilized power
supply (24V DC)
Terminal
resistor
PW
RUN
L RUN
SD
RD
L ERR.
Appendix 14
14-1
14. Appendix
Parameter setting sheet
Table 14.1:
Item Setting range
Buffer
memory
address
Remarks Default
Preset
value
Number of
connected modules
1 to 15 1H 8
Number of retries 1 to 7 2H 3
Number of automatic
return modules
1 to 10 3H 1
Operation
specification against
CPU down
0: Stop, 1: Continue 6H 0 (stop)
Reserved station
specification
Set to 1 the bits
corresponding to
reserved stations.
10H Station Nos. 15 to 1 0000H
Invalid station
specification
Set to 1 the bits
corresponding to invalid
stations.
14H Station Nos. 15 to 1 0000H
Station information b15 to b12 (station type)
0: Remote I/O station
1: Remote device station
b11 to b8 (number of
occupied stations)
1: Occupies 1 station.
2: Occupies 2 stations.
3: Occupies 3 stations.
4: Occupies 4 stations.
b7 to b0 (station number)
01H to 1FH (1 to 15)
20H 1st module 0101H
21H 2nd module 0102H
22H 3rd module 0103H
23H 4th module 0104H
24H 5th module 0105H
25H 6th module 0106H
26H 7th module 0107H
27H 8th module 0108H
28H 9th module 0109H
29H 10th module 010AH
2AH 11th module 010BH
2BH 12th module 010CH
2CH 13th module 010DH
2DH 14th module 010EH
2EH 15th module 010FH
FX2N-16CCL-M CC-Link System Master Block
FX2N-16CCL-M CC-Link System Master Block Appendix 14
14-2
Station information setting sheet
Table 14.2:
Station
number
Station type
Number of
occupied stations
Reserved station/invalid station
specification
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
FX2N-16CCL-M CC-Link System Master Block Appendix 14
14-3
Device assignment sheet (remote I/O)
Device assignment sheet (remote register)
Table 14.3:
Station
number
Remote input (RX) Remote output (RY)
1 RX00 to RX1F RY00 to RY1F
2 RX20 to RX3F RY20 to RY3F
3 RX40 to RX5F RY40 to RY5F
4 RX60 to RX7F RY60 to RY7F
5 RX80 to RX9F RY80 to RY9F
6 RXA0 to RXBF RYA0 to RYBF
7 RXC0 to RXDF RYC0 to RYDF
8 RXE0 to RXFF RYE0 to RYFF
9 RX100 to RX11F RY100 to RY11F
10 RX120 to RX13F RY120 to RY13F
11 RX140 to RX15F RY140 to RY15F
12 RX160 to RX17F RY160 to RY17F
13 RX180 to RX19F RY180 to RY19F
14 RX1A0 to RX1BF RY1A0 to RY1BF
15 RX1C0 to RX1DF RY1C0 to RY1DF
Table 14.4:
Station
number
Write (RWw) Read (RWr)
1 RWw0 to RWw3 RWr0 to RWr3
2 RWw4 to RWw7 RWr4 to RWr7
3 RWw8 to RWwB RWr8 to RWrB
4 RWwC to RWwF RWrC to RWrF
5 RWw10 to RWw13 RWr10 to RWr13
6 RWw14 to RWw17 RWr14 to RWr17
7 RWw18 to RWw1B RWr18 to RWr1B
8 RWw1C to RWw1F RWr1C to RWr1F
9 RWw20 to RWw23 RWr20 to RWr23
10 RWw24 to RWw27 RWr24 to RWr27
11 RWw28 to RWw2B RWr28 to RWr2B
12 RWw2C to RWw2F RWr2C to RWr2F
13 RWw30 to RWw33 RWr30 to RWr33
14 RWw34 to RWw37 RWr34 to RWr37
15 RWw38 to RWw3B RWr38 to RWr3B
FX2N-16CCL-M CC-Link System Master Block Appendix 14
14-4
MEMO
MITSUBISHI ELECTRIC
MITSUBISHI
ELECTRIC
FACTORY AUTOMATION
Mitsubishi Electric Europe B.V. /// FA - European Business Group /// Gothaer Strae 8 /// D-40880 Ratingen /// Germany
Tel.: +49(0)2102-4860/// Fax: +49(0)2102-4861120/// [email protected]/// www.mitsubishi-automation.com
Specifications subject to change /// 01.2008
HEADQUARTERS
MITSUBISHI ELECTRIC EUROPE B.V.
German Branch
Gothaer Strae 8
Phone: +49 (0)2102 / 486-0
Fax: +49 (0)2102 / 486-1120
MITSUBISHI ELECTRIC EUROPE B.V.
French Branch
25, Boulevard des Bouvets
Phone: +33 (0)1 / 55 68 55 68
Fax: +33 (0)1 / 55 68 57 57
MITSUBISHI ELECTRIC EUROPE B.V.
Irish Branch
Westgate Business Park, Ballymount
Phone: +353 (0)1 4198800
Fax: +353 (0)1 4198890
MITSUBISHI ELECTRIC EUROPE B.V.
Italian Branch
Viale Colleoni 7
Phone: +39 039 / 60 53 1
Fax: +39 039 / 60 53 312
MITSUBISHI ELECTRIC CORPORATION
Office Tower Z 14 F
Tokyo 104-6212
Phone: +81 3 622 160 60
Fax: +81 3 622 160 75
MITSUBISHI ELECTRIC EUROPE B.V.
UK Branch
Travellers Lane
Phone: +44 (0)1707 / 27 61 00
Fax: +44 (0)1707 / 27 86 95
MITSUBISHI ELECTRIC EUROPE B.V.
Spanish Branch
Carretera de Rub 76-80
Phone: +34 93 / 565 3131
Fax: +34 93 / 589 1579
USA MITSUBISHI ELECTRIC AUTOMATION
500 Corporate Woods Parkway
Phone: +1 847 478 21 00
Fax: +1 847 478 22 83
EUROPEANREPRESENTATIVES
GEVA
Wiener Strae 89
Phone: +43 (0)2252 / 85 55 20
Fax: +43 (0)2252 / 488 60
TEHNIKON
Oktyabrskaya 16/5, Off. 703-711
Phone: +375 (0)17 / 210 46 26
Fax: +375 (0)17 / 210 46 26
Koning & Hartman B.V.
Industrial Solutions
Woluwelaan 31
Phone: +32 (0)2 / 257 02 40
Fax: +32 (0)2 / 257 02 49
AKHNATON
4 Andrej Ljapchev Blvd. Pb 21
Phone: +359 (0)2 / 97 44 05 8
Fax: +359 (0)2 / 97 44 06 1
INEA CR d.o.o.
Losinjska 4 a
Phone: +385 (0)1 / 36 940 - 01/ -02/ -03
Fax: +385 (0)1 / 36 940 - 03
AutoCont Control Systems, s.r.o.
Jelinkova 59/3
Phone: +420 (0)59 / 5691 150
Fax: +420 (0)59 / 5691 199
AutoCont Control Systems, s.r.o.
Technologick 374/6
Phone: +420 595 691 150
Fax: +420 595 691 199
B:TECH, a.s.
Na Ostrove 84
Phone: +420 (0)569 / 408 841
Fax: +420 (0)569 / 408 889
B:TECH, a.s.
Headoffice
U Borov 69
Phone: +420 569 777 777
Fax: +420 569 777 778
Beijer Electronics A/S
Lautruphoj 1-3
Phone: +45 (0)70 / 26 46 46
Fax: +45 (0)70 / 26 48 48
Beijer Electronics Eesti O
Prnu mnt.160i
Phone: +372 (0)6 / 51 81 40
Fax: +372 (0)6 / 51 81 49
Beijer Electronics OY
Jaakonkatu 2
Phone: +358 (0)207 / 463 500
Fax: +358 (0)207 / 463 501
UTECO A.B.E.E.
5, Mavrogenous Str.
Phone: +30 211 / 1206 900
Fax: +30 211 / 1206 999
Meltrade Ltd.
Fert utca 14.
Phone: +36 (0)1 / 431-9726
Fax: +36 (0)1 / 431-9727
Beijer Electronics SIA
Vestienas iela 2
Phone: +371 (0)784 / 2280
Fax: +371 (0)784 / 2281
EUROPEANREPRESENTATIVES
Beijer Electronics UAB
Savanoriu Pr. 187
Phone: +370 (0)5 / 232 3101
Fax: +370 (0)5 / 232 2980
INTEHSIS srl
bld. Traian 23/1
Phone: +373 (0)22 / 66 4242
Fax: +373 (0)22 / 66 4280
Koning & Hartman B.V.
Haarlerbergweg 21-23
Phone: +31 (0)20 / 587 76 00
Fax: +31 (0)20 / 587 76 05
Beijer Electronics AS
Postboks 487
Phone: +47 (0)32 / 24 30 00
Fax: +47 (0)32 / 84 85 77
MPL Technology Sp. z o.o.
Ul. Krakowska 50
Phone: +48 (0)12 / 630 47 00
Fax: +48 (0)12 / 630 47 01
Sirius Trading & Services srl
Aleea Lacul Morii Nr. 3
Phone: +40 (0)21 / 430 40 06
Fax: +40 (0)21 / 430 40 02
CRAFT Consulting & Engineering d.o.o.
Bulevar Svetog Cara Konstantina 80-86
Phone: +381 (0)18 / 292-24-4/5 , 523 962
Fax: +381 (0)18 / 292-24-4/5 , 523 962
INEA SR d.o.o.
Karadjordjeva 12/260
Phone: +381 (0)26 / 617 163
Fax: +381 (0)26 / 617 163
CS MTrade Slovensko, s.r.o.
Vajanskeho 58
Phone: +421 (0)33 / 7742 760
Fax: +421 (0)33 / 7735 144
INEA d.o.o.
Stegne 11
Phone: +386 (0)1 / 513 8100
Fax: +386 (0)1 / 513 8170
Beijer Electronics Automation AB
Box 426
Phone: +46 (0)40 / 35 86 00
Fax: +46 (0)40 / 35 86 02
ECONOTEC AG
Hinterdorfstr. 12
Phone: +41 (0)44 / 838 48 11
Fax: +41 (0)44 / 838 48 12
GTS
Darulaceze Cad. No. 43 KAT. 2
Phone: +90 (0)212 / 320 1640
Fax: +90 (0)212 / 320 1649
CSC Automation Ltd.
15, M. Raskova St., Fl. 10, Office 1010
Phone: +380 (0)44 / 494 33 55
Fax: +380 (0)44 / 494-33-66
EURASIANREPRESENTATIVES
Kazpromautomatics Ltd.
2, Scladskaya str.
Phone: +7 3212 / 50 11 50
Fax: +7 3212 / 50 11 50
ELEKTROSTILY
Rubzowskaja nab. 4-3, No. 8
Phone: +7 495 / 545 3419
Fax: +7 495 / 545 3419
ICOS
Industrial Computer Systems ZAO
Ryazanskij Prospekt, 8A, Office 100
Phone: +7 495 / 232 0207
Fax: +7 495 / 232 0327
NPP URALELEKTRA
Sverdlova 11A
Phone: +7 343 / 353 2745
Fax: +7 343 / 353 2461
MIDDLE EAST
REPRESENTATIVES
Ilan & Gavish Ltd.
Automation Service
24 Shenkar St., Kiryat Arie
Phone: +972 (0)3 / 922 18 24
Fax: +972 (0)3 / 924 0761
Texel Electronics Ltd.
2 Haumanut, P.O.B. 6272
Phone: +972 (0)9 / 863 08 91
Fax: +972 (0)9 / 885 24 30
AFRICANREPRESENTATIVE
CBI Ltd.
Private Bag 2016
Phone: + 27 (0)11 / 928 2000
Fax: + 27 (0)11 / 392 2354