Author:

Arabian Drilling
Company
REF: 3
Checked By: ARS BADER
Rig Specifc
Procedure
Page
Approed By: R!S "ASSA#
A$ "%$A$
AD & 3'
%((ued: Sept ')*)
Subject: Rig Specific
Procedures
Prepare
Ca(ing
+er(ion *
1.1 OBJECTIVE.
A key objective of ADC Procedures is to set up a step by step way of handling the
job. It is also an analysis of associated hazards pertaining to the jobs and measures to
minimize the risks.
his procedure has developed to be applied and discussed before each job listed in
the contents.
1.2 SCOPE.
his procedure applies to !ig AD-32
1.3 RESPONSIBILITY.
It is the responsibility of the ool"pusher and !ig #anager to insure all listed
operations are e$ecuted in a safe and efficient manner. It is the oolpusher
responsibility to conduct a Pre"job %afety #eeting and discuss and review the related
&%A' prior to starting each operation.
ool"pusher is responsible to ensure that each work permit has its dedicated &%A
attached to.

&%A to be reviewed and updated at least annually or
(hen e)uipment is modified
(hen processes are changed
(hen material are changed
(hen changing people*contractors
(hen there is an accident or near miss.
he !ig %up. is accountable for keeping this document up"to +date.
he &%A date and the crew should be same as (ork Permit date and crew.
Author:
Arabian Drilling
Company
REF: 3
Checked By: ARS BADER
Rig Specifc
Procedure
Page
Approed By: R!S "ASSA#
A$ "%$A$
AD & 3'
%((ued: Sept ')*)
Subject: Rig Specific
Procedures
Prepare
Ca(ing
+er(ion *
Table of Contents
TASK ANALYSIS
Is Procedure relevant for the operation?
YES
What can interfere with the operation (Simops)?
Who is going to be in charge position?
! "#$ "%S %#S
Who is giving instructions#signals who replace him?
! %#S
&ow man' people are re(uired to do the )ob?
! %#" Position
! %#" Position
! %"P Position
! "#$ Position
! "%S Position
! Position
$o 'ou need a P*W# Isolation (loc+out *ag out)?
! YES
What is the PPE re(uired?
! S",E*Y S&-ES &"%$ &"*
! S",*EY ./"SSES
What tools#e(uipment do 'ou need?
! 0E"S1%E *"PE
! S/I2.
! *". /I2E
! PIPE W%E23&
$o 'ou need a third part' crane and for+lift?
! 3%"2E "2$ ,-%4/I,*
Who else needs to +now what 'ou are doing?
! SI.2"/ 0"2 ,-% 3%"2E -PE%"*-%
!
$o 'ou need to barrier off the area?
!
What are the safest access#escape routes?
!
Author:
Arabian Drilling
Company
REF: 3
Checked By: ARS BADER
Rig Specifc
Procedure
Page
Approed By: R!S "ASSA#
A$ "%$A$
AD & 3'
%((ued: Sept ')*)
Subject: Rig Specific
Procedures
Prepare
Ca(ing
+er(ion *
"dditional 3omments5
Preparation
%eview 6S" number 7 related8
Inform 3lients representative before ma+ing up the Shoe#,loat collar
connections8
3asing tall' to be prepared b' 3lients representative *ool Pusher to review8
Pre!)ob given hold b' tool pusher with crewmen8
3orrect Personal Protective E(uipment worn b' crew men8
P*W for be filled in and signed b' $riller and 0I3 prior to start ma+ing the
shoe#float collar connection8
Tools
,or+lift 3rane
Slings
*ag lines
Wood plan+s and choc+s
Pipe wrenches
Pipe rac+s
"PI $rift(s)
Wire rope
0easuring tape
&igh Pressure washer
Wire brushes
9arite
9a+erloc+ compound
Paint paint brushes
Procedure
Make sure te pipe racks are pinned to te cat!alk before "ou la" do!n an" pipe#
:8 -nce received on site the casing must be laid down gentl' and disposed properl'
on the pipe rac+s with the for+lift#crane8
Safet' Precautions5
-nl' approved drivers to drive the for+lift#crane8
1se tag lines to control all crane loads never handle directl'8
Author:
Arabian Drilling
Company
REF: 3
Checked By: ARS BADER
Rig Specifc
Procedure
Page
Approed By: R!S "ASSA#
A$ "%$A$
AD & 3'
%((ued: Sept ')*)
Subject: Rig Specific
Procedures
Prepare
Ca(ing
+er(ion *
2obod' on ground rac+s when collecting or pic+ing up 3asing 6oints8
%oll 3asing 6oints from end onl' nobod' between or in front8
1se Wood plan+s and 3hoc+s if two la'ers of tubular must be disposed8
;8 3hec+ with 3ompan' man which casing goes first in the hole in case of different
t'pe of threads or grades in order to organi<e on the pipe rac+s8
78 *he Pin and 9o= protectors shall be removed and disposed properl' in a close
area8 9e careful that the' dont drop on 'our feet while removing them8 1se a Pipe
wrench if needed8
>8 3hec+ with the *ool Pusher the +ind of drift to be used (according to the weight of
the casing) and measure the drift diameter 'ourself prior to use it8
?8 $rift the casings and remove after clear identification an' tight )oint8 *he use of
pressuri<ed air is forbidden during all operations related to casing drift8 1se wire
rope (:#;@ diameter) to pull the drift8
Safet' Precaution5
1se /eather gloves to handle wire rope
A8 0easure the drifted )oints with the measuring tape8 %ecord the measure with ;
decimals precision in the casing tall' note boo+8 -nl' one tape measure to be used
all the wa' along8 "gree with 3ompan' man and *ool pusher on the length to
substract for the pin end of the )oints8
B8 3lean thoroughl' the couplings with &igh!Pressure water and Shellsol8 1se a wire
brush for better cleaning8 $ispose a $rip pan below the )oints being cleaned up to
prevent environmental spill8
C8 -nce cleaned the crew shall inspect the threads for damage8 *he cleaned )oints
must also be inspected b' *ool!Pusher8 Identif' and remove an' bad )oint8
D8 Paint )oint number and length on each respective )oint
:E8 -nce the casing tall' has been delivered b' the 3lients representative start
installing the centrali<ers on the respective )oints according to his instructions8
Safet' Precautions5
4eep hands clear when fitting centrali<ers hold b' blades8
&ammer nails gentl'8 1se a pipe to bend the centrali<er nails8
Wear Safet' .lasses
Author:
Arabian Drilling
Company
REF: 3
Checked By: ARS BADER
Rig Specifc
Procedure
Page
Approed By: R!S "ASSA#
A$ "%$A$
AD & 3'
%((ued: Sept ')*)
Subject: Rig Specific
Procedures
Prepare
Ca(ing
+er(ion *
Make up Soe$%loat
::8 *he 0a+e up of Shoe#,loat 3ollar connections shall be done with presence of the
%ig Supt and 3lients representative8 ,ollow the procedure detailed here below5
:) ,ill!in and get signature for Wor+ Permit8
;) Secure the area with barrier tape
7) 3hain down firml' the casing )oint on a device on the dec+8
>) 3hec+ the ball in the shoe#float collar is authori<ing the flow in one wa' onl' 8
?) 3lean the casing )oint threads and shoe#float collar couplings with rig
Shellsol mi=ed with water
A) %inse with Water8 $r' the couplings with bentonite and wire brush the
threads8
B) %emove the bentonite with Pressuri<ed air8 %emind 'our safet' goggles8
C) Inspect the threads to ensure there is no damage8
D) Engage the first threads of the shoe#float collar b' hand8 (Wrap rope and pull
slowl')8
:E)When first threads confirmed to be made up o+ appl' /oc+ing *hread
compound (9a+er!/oc+) on the upper part of casing )oint threads8
::) "ppl' the correct tor(ue on the shoe8 1se a strong chain tong with a load cell
and gauge (length of arm) to tor(ue the shoe and an other one as a bac+up8
*he crane operator must loo+ cautiousl' his load sensor and operate gentl'
according to *ool Pushers orders8 *he crew members shall loo+ for slip of
the casing and rearrange properl' the tongs if needed8
Safet' Precautions5
*he crew members shall stand clear of tongs and crane8
3ommunication and safe behavior are +e's of a successful operation8
:;)-nce the correct tor(ue is reached release the tension gentl' and put bac+
the tools in place8
:7)%emove the barrier tape
Author:
Arabian Drilling
Company
REF: 3
Checked By: ARS BADER
Rig Specifc
Procedure
Page
Approed By: R!S "ASSA#
A$ "%$A$
AD & 3'
%((ued: Sept ')*)
Subject: Rig Specific
Procedures
Prepare
Ca(ing
+er(ion *
:>)3lose P*W8