Page 1 of 8

Health and Safety

Executive
Lifting equipment at work
A brief guide
This is a web-friendly
version of leaflet
INDG290(rev1),
published 03/13
Introduction
This leaflet provides general information about the requirements of the Lifting
Operations and Lifting Equipment Regulations 1998 (LOLER). It describes what
you, as an employer, may need to do to protect your employees in the workplace.
It will also be useful to employees and their representatives.
However, it is important that you also refer to the Regulations and Approved Code
of Practice to familiarise yourself fully with your duties.
What equipment is covered by the Regulations?
Lifting equipment includes any equipment used at work for lifting or lowering loads,
including attachments used for anchoring, fixing or supporting it. The Regulations
cover a wide range of equipment including, cranes, forklift trucks, lifts, hoists,
mobile elevating work platforms, and vehicle inspection platform hoists. The
definition also includes lifting accessories such as chains, slings, eyebolts etc.
LOLER does not apply to escalators, which are covered more specifically by the
Workplace (Health, Safety and Welfare) Regulations 1992.
If you allow employees to provide their own lifting equipment, then this too is
covered by and should comply with the Regulations.
Do the Regulations apply to me?
If you are an employer or self-employed person providing lifting equipment for use
at work, or you have control of the use of lifting equipment, then the Regulations
will apply to you. They do not apply if you provide equipment to be used primarily
by members of the public, for example lifts in a shopping centre. However, such
circumstances are covered by the Health and Safety at Work etc Act 1974 (HSW Act).
While your employees do not have specific duties under LOLER, they do have
general duties under the HSW Act and the Management of Health and Safety at
Work Regulations 1999 (the Management Regulations), for example to take
reasonable care of themselves and others who may be affected by their actions
and to co-operate with others.
The Regulations cover workplaces where the HSW Act applies this includes
factories, offshore installations, agricultural premises, offices, shops, hospitals,
hotels, places of entertainment etc.
Health and Safety
Executive
Lifting equipment at work: A brief guide Page 2 of 8
What do the Regulations require me to do?
You need to make sure that when using any lifting equipment the requirements of
LOLER are met. For example, you should make sure that all lifting equipment is:
sufficiently strong, stable and suitable for the proposed use. Similarly, the load

and anything attached (eg timber pallets, lifting points) must be suitable;
positioned or installed to prevent the risk of injury, eg from the equipment or

the load falling or striking people;

visibly marked with any appropriate information to be taken into account for its

safe use, eg safe working loads. Accessories, eg slings, clamps etc, should be
similarly marked.
Additionally, you must make sure that:
lifting operations are planned, supervised and carried out in a safe manner

by people who are competent;

where equipment is used for lifting people it is marked accordingly, and it

should be safe for such a purpose, eg all necessary precautions have been
taken to eliminate or reduce any risk;
where appropriate, before lifting equipment (including accessories) is used for

the first time, it is thoroughly examined. Lifting equipment may need to be

thoroughly examined in use at periods specified in the Regulations (ie at least
six-monthly for accessories and equipment used for lifting people and, at a
minimum, annually for all other equipment) or at intervals laid down in an
examination scheme drawn up by a competent person. All examination work
should be performed by a competent person (someone with the necessary
skills, knowledge and experience);
following a thorough examination or inspection of any lifting equipment, a

report is submitted by the competent person to the employer to take the

appropriate action.
Why is lifting equipment safety important?
Working with any machinery can be dangerous because moving machinery can
cause injuries in many ways:
People can be hit and injured by moving parts of machinery or dropped or

ejected material. Parts of the body can also be drawn in or trapped between
rollers, belts, chains and pulley drives.
Sharp edges can cause cuts and severing injuries, sharp-pointed parts can

stab or puncture the skin, and rough surface parts can cause friction or abrasion.
People can be crushed both between parts moving together or towards a fixed

part of the machine, wall or other object, and two parts moving past one
another can cause shearing.
Parts of the machine, materials and emissions (such as steam or water) can be

hot or cold enough to cause burns or scalds and electricity can cause electrical
shock and burns.
Equipment or attachments can become unreliable and develop faults due to

poor or no maintenance, or machines may be used improperly through

inexperience or lack of training.
Parts of the equipment may fail and loads may drop.

Health and Safety

Executive
Lifting equipment at work: A brief guide Page 3 of 8
Before you start
Before you start using any equipment you need to think about what risks may
occur and how these can be managed. You should:
Check that it is complete, with all safeguards fitted, and free from defects.

Produce a safe system of work for using and maintaining the equipment.

Maintenance may require the inspection of critical features where deterioration

would cause a risk. Also look at the residual risks identified by the manufacturer
in their information/instructions provided with the equipment and make sure
they are included in the safe system of work.
Make sure the equipment has been installed properly, is stable and is not in a

location where other workers, customers or visitors may be exposed to risk.

Make sure you have chosen the right equipment for the job.

Note that new equipment should be CE marked and be supplied with a Declaration
of Conformity and instructions in English.
Make sure the equipment is:
safe for any work that has to be done when setting up, during normal use,

when carrying out repairs for breakdowns or faults, and during planned
maintenance;
properly switched off, isolated or locked-off before taking any action to remove

blockages, clean or adjust the equipment.

Also, make sure you identify and deal with the risks from:
electrical, hydraulic or pneumatic power supplies;

badly designed safeguards. These may be inconvenient to use or easily

overridden, which could encourage your workers to risk injury and break the
law. If they are, find out why they are doing it and take appropriate action to
deal with the reasons/causes.
Preventing access to dangerous parts
Think about how you can make the equipment safe; the measures you use to
prevent access to dangerous parts should be in the following order. In some cases
it may be necessary to use a combination of these measures:
Use fixed guards (eg secured with screws or nuts and bolts) to enclose the

dangerous parts, whenever practicable. Use the best material for these guards
plastic may be easy to see through but may easily be damaged. Where you
use wire mesh or similar materials, make sure the holes are not large enough to
allow access to moving parts.
If fixed guards are not practicable, use other methods, eg interlock the guard

so that the equipment cannot be started before the guard is closed and cannot
be opened while the machine is still moving. In some cases, trip systems (such
as photoelectric devices, pressure-sensitive mats or automatic guards) may be
used if other guards are not practicable.
Where guards cannot give full protection, use jigs, holders, push sticks etc if it

is practicable to do so.
Control any remaining risk by providing the operator with the necessary

information, instruction, training, supervision and appropriate safety equipment.

Health and Safety
Executive
Lifting equipment at work: A brief guide Page 4 of 8
Other things you should consider
Make sure control switches are clearly marked to show what they do.

Have emergency stop controls where necessary, eg mushroom-head push

buttons within easy reach.

Make sure operating controls are designed and placed to avoid accidental

operation and injury. Use two-hand controls where necessary and shroud start
buttons and pedals.
Do not let unauthorised, unqualified or untrained people use lifting equipment

never allow children to operate or help with lifting equipment. Some workers,
eg new starters, young people or those with disabilities, may be particularly at
risk and need instruction, training and supervision.
Adequate training should ensure that those who use the equipment are

competent to use it safely (they have the necessary skills, knowledge and
experience), and are physically suited to the task.
Make sure the work area around the equipment is kept clean and tidy, free

from obstructions or slips and trips hazards, and well lit.

Dos and donts of equipment safety
As the dutyholder you should make sure that all employees likely to use lifting
equipment, understand and follow these dos and donts:
Do
check the equipment is well maintained and fit to be used, ie appropriate for

the job, working properly and all the safety measures are in place;
make sure all parts, including attachments, can accommodate the load weight;

use the equipment properly and in accordance with the manufacturers instructions;

make sure employees are wearing the appropriate protective clothing and

equipment, required for that machine, such as safety glasses, head protection
and safety shoes.
Dont
use equipment that has a danger sign or tag attached to it. Danger signs

should only be removed by an authorised person who is satisfied that the

equipment or process is now safe;
remove any safeguards, even if their presence seems to make the job

more difficult;
wear dangling chains, loose clothing, rings or have loose long hair that

could get caught up in moving parts;

distract people who are using equipment.

Safe lifting by machine

If you are an employer or a self-employed person providing lifting equipment for
use at work, or if you have control of the use of lifting equipment, you must make
sure it is safe. Think about what risks there may be and how they can be managed.
For example:
damage or deterioration of the equipment or attachments caused by wet,

abrasive or corrosive environments;

trying to move weights that are too heavy and exceed the load limit of the machine;

equipment failure;

Health and Safety

Executive
Lifting equipment at work: A brief guide Page 5 of 8
untrained workers planning the lift or using the equipment;

people being struck by moving parts of the equipment or by things falling.

Safe lifting needs to be properly planned by a competent person, appropriately

supervised and carried out safely. Any equipment you use must have been
properly designed, manufactured and tested. Dont forget maintenance.
Factors you should consider
What are you lifting, and what problems does it present?

How heavy is it, and is this within the safe limits for the lifting gear?

Where is its centre of gravity?

How will you attach it to the lifting machinery?

Who is in control of the lift?

Could you rehearse the lift if necessary?

Dos and donts of lifting safely

Do:
use only certified lifting equipment, marked with its safe working load, which is

not overdue for examination;

keep the reports of thorough examination as well as any declarations of

conformity or test certificates;

make sure the load is properly attached to the lifting equipment. If necessary,

securely bind the load to prevent it slipping or falling off;

before lifting an unbalanced load, find out its centre of gravity. Raise it a few

inches off the ground and pause there will be little harm if it drops;
use packaging to prevent sharp edges of the load from damaging slings and do

not allow tackle to be damaged by being dropped, dragged from under loads
or subjected to sudden loads;
when using jib cranes, make sure any indicators for safe loads are working

properly and set correctly for the job and the way the machine is configured;
use outriggers where necessary;

when using multi-slings make sure the sling angle is taken into account;

have a responsible slinger or banksman and use a recognised signalling system.

Dont
use unsuitable equipment, eg makeshift, damaged, badly worn chains

shortened with knots, kinked or twisted wire ropes, frayed or rotted fibre ropes;
exceed the safe working load of machinery or accessories like chains, slings

and grabs. Remember that the load in the legs of a sling increases as the angle
between the legs increases;
lift a load if you doubt its weight or the adequacy of the equipment.

Equipment maintenance
Why is maintenance of equipment important?
Additional hazards can occur when equipment becomes unreliable and develops
faults. Maintenance allows these faults to be diagnosed early and corrected to
manage any risks. However, maintenance needs to be correctly planned and
carried out. Unsafe maintenance has caused many fatalities and serious injuries
either during the maintenance or to those using the badly or wrongly maintained/
repaired equipment.
Health and Safety
Executive
Lifting equipment at work: A brief guide Page 6 of 8
An effective maintenance programme will make equipment more reliable. Fewer
breakdowns will mean less dangerous contact with equipment is required, as well
as having the cost benefits of better productivity and efficiency.
LOLER requires lifting equipment to be maintained so that it remains safe and that
maintenance is carried out safely.
What do I have to do?
If you are an employer and you provide lifting equipment you need to demonstrate
that you have arrangements in place to make sure they are maintained in a safe
condition.
Think about what hazards can occur:
if equipment or an attachment breaks during use;

equipment starts up unexpectedly;

there is contact with materials that are normally enclosed within the machine,

ie caused by leaks/breakage/ejection etc;

if a load or part of a load falls.

Failing to correctly plan and communicate clear instructions and information before
starting maintenance can lead to confusion and can cause accidents. This can be a
particular problem if maintenance is carried out during normal production work or
where there are contractors who are unfamiliar with the site.
Extra care is also required if maintenance involves:
working at height or when doing work that requires access to unusual parts

of the building;
entering vessels or confined spaces where there may be toxic materials or a

lack of breathable of air.

How can I do it?
Establish a planned maintenance programme and a reporting procedure for
workers who may notice problems while working on machinery.
Some items of equipment may have safety-critical features where deterioration
would cause a risk. You must have arrangements in place to make sure the
necessary inspections take place.
But there are other steps to consider:
Before you start maintenance
Decide if the work should be done by specialist contractors. Never take on

work for which you are not competent or not prepared.

Plan the work carefully before you start, ideally using the manufacturers

maintenance instructions, and produce a safe system of work. This will

reduce the risks and avoid unforeseen delays.
Make sure maintenance staff are competent and have appropriate clothing

and equipment.
Try and use downtime for maintenance. You can avoid the difficulties in

co-ordinating maintenance and lost production if maintenance work is

performed before start-up or during shutdown periods.
Health and Safety
Executive
Lifting equipment at work: A brief guide Page 7 of 8
Safe working areas
You must provide safe access and a safe place of work.

Dont just focus on the safety of maintenance workers take the necessary

precautions to ensure the safety of others who may be affected by their work,
eg other employees or contractors working nearby.
Set up signs and barriers and position people at key points if they are needed

to keep other people out.

How do the Regulations relate to other health and
safety legislation?
The requirements of the Regulations need to be considered alongside other health
and safety law. For example, section 2 of the HSW Act requires all employers to
ensure, so far as is reasonably practicable, the health, safety and welfare of all their
employees. Similarly, the Management Regulations contain important duties which
relate to the carrying out of a risk assessment to identify measures that you can
take to eliminate, or reduce, the risks presented by the particular hazards in your
workplace (see Further information).
Other more specific legislation, for example the Personal Protective Equipment at
Work Regulations 1992, may also apply. Under these particular Regulations there
may be a need to provide a safety harness for rope access work during activities
such as window cleaning.
Further reading
Safe use of lifting equipment. Lifting Operations and Lifting Equipment Regulations
1998. Approved Code of Practice and guidance L113 HSE Books 1998
ISBN 978 0 7176 1628 2 www.hse.gov.uk/pubns/books/l113.htm
Safe use of work equipment. Provision and Use of Work Equipment Regulations
1998. Approved Code of Practice and guidance L22 (Third edition)
HSE Books 2008 ISBN 978 0 7176 6295 1 www.hse.gov.uk/pubns/books/l22.htm
Providing and using work equipment safely: A brief guide to the law Leaflet
INDG291(rev1) HSE Books 2013 www.hse.gov.uk/pubns/indg291.htm
Managing health and safety: Five steps to success Leaflet INDG275
HSE Books 1998 www.hse.gov.uk/pubns/indg275.htm
Buying new machinery: A short guide to the law and your responsibilities when
buying new machinery for use at work Leaflet INDG271(rev1) HSE Books 2011
www.hse.gov.uk/pubns/indg271.htm
Workplace transport safety: An employers guide HSG136 (Second edition)
HSE Books 2005 ISBN 978 0 7176 6154 1 www.hse.gov.uk/pubns/books/hsg136.htm
Workplace transport safety: A brief guide Leaflet INDG199(rev1) HSE Books 2013
www.hse.gov.uk/pubns/indg199.htm
Hiring and leasing out of plant: Application of PUWER 98, regulations 26 and 27
MISC156 HSE Books 1998 www.hse.gov.uk/pubns/9204.pdf
Risk management web pages: www.hse.gov.uk/risk/
Health and Safety
Executive
Page 8 of 8
Health and Safety
Executive
Further information
For information about health and safety, or to report inconsistencies or inaccuracies
in this guidance, visit www.hse.gov.uk/. You can view HSE guidance online and
order priced publications from the website. HSE priced publications are also
available from bookshops.
This guidance is issued by the Health and Safety Executive. Following the guidance
is not compulsory, unless specifically stated, and you are free to take other action.
But if you do follow the guidance you will normally be doing enough to comply with
the law. Health and safety inspectors seek to secure compliance with the law and
may refer to this guidance.
This leaflet is available at www.hse.gov.uk/pubns/indg290.htm.
Crown copyright If you wish to reuse this information visit
www.hse.gov.uk/copyright.htm for details. First published 03/13.
Published by the Health and Safety Executive 03/13 INDG290(rev1)