Scribd
Upload
33 views

Sub-And Supersonic Aerodynamical Shapes Without Separation: I. Nesteruk

This document summarizes research on axisymmetric and two-dimensional shapes that can achieve unseparated flow patterns. It discusses two methods for preventing flow separation: 1) using very slender bodies or thin profiles, and 2) using special forms with appropriate pressure distributions, such as negative pressure gradients on the surface. Equations from potential flow theory are presented for calculating shapes with negative pressure gradients. Experimental results show shapes with negative pressure gradients can achieve unseparated flow up to Reynolds numbers of 300,000. Further experimental testing of these shapes at higher speeds is recommended.

Uploaded by

mhdmk
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
33 views

Sub-And Supersonic Aerodynamical Shapes Without Separation: I. Nesteruk

This document summarizes research on axisymmetric and two-dimensional shapes that can achieve unseparated flow patterns. It discusses two methods for preventing flow separation: 1) using very slender bodies or thin profiles, and 2) using special forms with appropriate pressure distributions, such as negative pressure gradients on the surface. Equations from potential flow theory are presented for calculating shapes with negative pressure gradients. Experimental results show shapes with negative pressure gradients can achieve unseparated flow up to Reynolds numbers of 300,000. Further experimental testing of these shapes at higher speeds is recommended.

Uploaded by

mhdmk
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

14th Annual (International) Mechanical Engineering Conference May 2006

Isfahan University of Technology, Isfahan, Iran

SUB- AND SUPERSONIC AERODYNAMICAL SHAPES


WITHOUT SEPARATION

I. Nesteruk
Institute of Hydromechanics, NASU, Zheliabova 8/4, 03680 Kyiv, Ukraine
[email protected]

Abstract
The slender body theory was applied to calculate axisymmetric bodies with negative pressure gradients at the surface
to ensure an unseparated flow pattern and to improve cavitation inception characteristics. A method of calculating of
axisymmetric and plane shapes in ideal compressible fluid, based on the potentials of sources and doublets located in
the axis of symmetry is proposed. Experimental investigations of axisymmetric shapes with specific pressure
distribution are reviewed. Some of such forms ensure unseparated flow pattern at relative small Reynolds numbers.

Keywords: AXISYMMETRIC SHAPES WITH NEGATIVE PRESSURE GRADIENTS IN


INCOMPRESSIBLE FLUID
There are two ways of obtaining the unseparated forms. The simplest one is to use very slender bodies or
very thin profiles, which probably ensure no separation independent of the pressure distribution over the
surface. The slender 2D and axisymmetric shapes are investigated in [1] with the use of the KochinLoitsiansky method of local similarity (see [2]). A parabolic symmetric profile with the coordinate of the
upper surface Y ( x) = 4(1 x) x and a body of revolution with the same parabolic generatrix were chosen
in [1] to estimate the value of the thickness parameter sufficient for the unseparated flow pattern. The
calculations show that the separation occurs for very small values of the thickness parameter . For
example, even for =0.01 the coordinates of the separation point are 0.906 (in the 2D case) and 0.912(in
axisymmetric flow). Thus, the simplest way of avoiding the separation is of limited practical interest.
The second way of preventing separation is to use some special forms with appropriate pressure
distributions. For example, negative pressure gradients at the body surface are necessary to avoid the
separation (see [2,3]). The majority of the researchers consider the minimum of the static pressure
coincident with the maximum of the body radius (or with the maximum of the thickness in the 2D case).
Moreover, they assume that the pressure gradient is positive after the maximum thickness point. This
paradigm was realized in so-called laminarized forms ([3]) obtained by shifting the maximum thickness
point as far downstream as possible. It would be interesting to investigate if it is possible to have negative
pressure gradients after the maximum thickness point too?
The first approximation of the slender body theory [4] yields the following equation relating the
axisymmetric body radius R(x) and the pressure coefficient Cp( x ) at its surface (see [1,5]):
d 2R2
dx

Cp( x )
.
ln

(1)

To make the trailing edge sharp, discontinuities of dR 2 / dx or d 2 R 2 / dx 2 at some


point x* , 0< x* <1 are required (see [6]). According to the first approximation
equation (1), the discontinuity of the second derivative d 2 R 2 / dx 2 provides the
discontinuity of the pressure. An example of such a solution obtained in [7] has the
following form:
ax 2c ,
Cp( x ) =
a1( x 1 ),

0 x < x*
x* x 1

14th Annual (International) Mechanical Engineering Conference May 2006


Isfahan University of Technology, Isfahan, Iran

Ex 2 ( ax + 6c ),
R2( x ) =
Ea1( x 1 )3 ,

0 x x*
x* x 1

, E=

1
6 ln

(2)

Fig.1 Shape with a negative pressure gradient. First


approximation.
.

Fig.2. Exact solution. Body radius,


theoretical and
experimental

pressure

distributions.

An example of the corresponding axisymmetric shape (curve 1) and the pressure distribution (curve 2) are
shown in Fig. 1. To improve the accuracy (eq. (1), (2) are not valid near the point x = x* ), some exact
solutions of the Euler equations have been calculated, which can be applied to non-slender bodies as well
(see [1, 6, 8]). For this purpose, sources and sinks were placed in the axis of symmetry. The first
approximation for their intensity q(x ) can be obtained from equation (2) and the relationship
q( x ) = dR 2 / dx (see [2]):

3Ex(ax + 4c),
q( x) =
3Ea1 ( x 1) 2 ,

0 x < x*

(3)

x* x 1

The appropriate analytical formula for the stream function ( x ,r ) is presented in [9]. An example of
calculations and the experimental pressure distributions for different Reynolds numbers are shown in Fig.
2. The shapes presented in Figs. 1,2 show that the pressure growth downstream of the maximum
thickness point is not obligatory. No separation occurred at the body shown in Fig.2 for
90000<Re<300000. Similar 2D profiles with a negative pressure gradient near to the trailing edge are
calculated in [1, 9].
AXISYMMETRIC AND 2D SHAPES WITHOUT SEPARATION IN COMPRESSIBLE FLOW

The results presented above can be easily generalized for the compressible flow. Using the stream
function of the sources located in the axis of symmetry the following eqs. can be written in sub- and
supersonic cases respectively:

( x, r ) = 0.5r 2

1
( x )q ()d
;

4 0 ( x ) 2 + (1 M 2 )r 2

( x, r ) = 0.5r 2

1
2

x r

( x )q()d
( x ) + (1 M )r
2

, = M 2 1

(4)

14th Annual (International) Mechanical Engineering Conference May 2006


Isfahan University of Technology, Isfahan, Iran

Here M is the Mach number at infinity. It was mentioned in [9] that the first approximation eq. (1) is
valid both for a subsonic and for a supersonic flow, therefore substituting relationship (3) into eq. (4)
analytic formulae for the stream function can be obtained. The body radius and the pressure distributions
at different values of M are calculated.
It was shown in [10] that intensity of sources (3) can be used in 2D case to calculate the form of
symmetric profile with negative pressure gradient both upstream and downstream the maximum thickness
point, which can ensure unseparated flow pattern as well (unfortunately no wind tunnel tests were
performed with such shapes). With the use of the stream function of the 2D sources located in the axis of
symmetry similar eqs. can be written in sub- and supersonic cases. The coordinate of the upper surface of
the profile and the pressure distributions at different values of M are calculated.
CONCLUSIONS

As the experiments show, the shapes with negative pressure gradients (similar to one shown in Fig.2 and
to U-1, [1]) provide the unseparated flow pattern. The presented axisymmetrical and 2D forms are of
considerable practical interest because they diminish the total drag (due to the small value of pressure
drag and the delay of the laminar-turbulent transition). Further experimental investigations of the
presented bodies and the profiles at higher Reynolds and Mach numbers are necessary.
References
[1] Nesteruk I.: Can Shapes with Negative Pressure Gradients Prevent Cavitation. 4th ASME/JSME Joint
Fluids Engineering Conference, Honolulu, USA, July 2003: FEDSM2003-45323, 2003.
[2] Loitsiansky L.G.: Mechanics of liquid and gas. Moscow, Nauka, 1978 (In Russian).
[3] Schlichting H.: Entstehung der Turbulenz, Handbuch der Physik, v. VII/1. : 341-450, 1959.

[4] Cole J.D.: Perturbation Methods in Applied Mathematics. Blaisdell, Waltham,


Toronto, London, 1968.
[5] Nesteruk I.: Investigation of Slender Axisymmetric Cavity Form in Ponderable
Fluid. Izv. AN SSSR, MZhG 6: 133-136, 1979 (In Russian).
[6] Buraga O.A., Nesteruk I., and Shepetyuk B.D.: Subsonic Axisymmetric Forms with a Pressure Jump
on the Surface. Naukovi visti, NTUU Kyiv Polytech. Inst. 1(15): 90-99, 2001 (In Ukrainian).
[7] Nesteruk I.: Some Problems of Slender Axisymmetric Cavitator Dynamics. Transactions of Boundary
Problems Seminar in Kazan University, 24: 187-197, 1990 (In Russian).
[8] Nesteruk I.: Experimental Investigation of Axisymmetric Bodies with Negative Pressure Gradients.
Aeronautical Journ. 104: 439-443, 2000.
[9] Nesteruk I.: Body forms of minimal drag. Dopovidi AN Ukr.SSR, ser. A, 4: 57-60, 1989 (in
Ukrainian).
[10] Nesteruk I.: Plane Subsonic Forms with Negative Pressure Gradients on Surface. Dopovidi NANU 9:
63-68, 2001.

You might also like