Scribd
Upload
843 views

2.3.2.5 Packet Tracer - Implementing Basic Connectivity Instructions

In this activity you will perform basic switch configurations. Then you will Implement Basic Connectivity by configuring IP addressing on switches and PCs. When the IP addressing configuration is complete, you will use various show commands to verify configurations and use the ping command to verify connectivity.

Uploaded by

Wendhz Üü
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
843 views

2.3.2.5 Packet Tracer - Implementing Basic Connectivity Instructions

In this activity you will perform basic switch configurations. Then you will Implement Basic Connectivity by configuring IP addressing on switches and PCs. When the IP addressing configuration is complete, you will use various show commands to verify configurations and use the ping command to verify connectivity.

Uploaded by

Wendhz Üü
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Packet Tracer - Implement Basic Connectivity

Topology

Addressing Table
Device

Interface

IP Address

Subnet Mask

S1

VLAN 1

192.168.1.253

255.255.255.0

S2

VLAN 1

192.168.1.254

255.255.255.0

PC1

NIC

192.168.1.1

255.255.255.0

PC2

NIC

192.168.1.2

255.255.255.0

Objectives
Part 1: Perform a Basic Configuration on S1 and S2
Part 2: Configure the PCs
Part 3: Configure the Switch Management Interface

Background
In this activity you will first perform basic switch configurations. Then you will implement basic connectivity by
configuring IP addressing on switches and PCs. When the IP addressing configuration is complete, you will
use various show commands to verify configurations and use the ping command to verify basic connectivity
between devices.

Part 1: Perform a Basic Configuration on S1 and S2


Complete the following steps on S1 and S2.

Step 1: Configure S1 with a hostname.


a. Click S1, and then click the CLI tab.
b. Enter the correct command to configure the hostname as S1.

Step 2: Configure the console and privileged EXEC mode passwords.

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 1 of 4

Packet Tracer - Implement Basic Connectivity


a. Use cisco for the console password.
b. Use class for the privileged EXEC mode password.

Step 3: Verify the password configurations for S1.


How can you verify that both passwords were configured correctly?
_______________________________________________________________________________________
_______________________________________________________________________________________
_______________________________________________________________________________________

Step 4: Configure a message of the day (MOTD) banner.


Use an appropriate banner text to warn unauthorized access. The following text is an example:
Authorized access only. Violators will be prosecuted to the full extent of the law.

Step 5: Save the configuration file to NVRAM.


Which command do you issue to accomplish this step?
_______________________________________________________________________________________
_______________________________________________________________________________________

Step 6: Repeat Steps 1 to 5 for S2.

Part 2: Configure the PCs


Configure PC1 and PC2 with IP addresses.

Step 1: Configure both PCs with IP addresses.


a. Click PC1, and then click the Desktop tab.
b. Click IP Configuration. In the Addressing Table above, you can see that the IP address for PC1 is
192.168.1.1 and the subnet mask is 255.255.255.0. Enter this information for PC1 in the IP
Configuration window.
c.

Repeat steps 1a and 1b for PC2.

Step 2: Test connectivity to switches.


a. Click PC1. Close the IP Configuration window if it is still open. In the Desktop tab, click Command
Prompt. .
b. Type the ping command and the IP address for S1, and press Enter.
Packet Tracer PC Command Line 1.0
PC> ping 192.168.1.253
Were you successful? Why or why not?
___________________________________________________________________________________.

Part 3: Configure the Switch Management Interface


Configure S1 and S2 with an IP address.

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 2 of 4

Packet Tracer - Implement Basic Connectivity

Step 1: Configure S1 with an IP address.


Switches can be used as a plug-and-play device, meaning they do not need to be configured for them to
work. Switches forward information from one port to another based on Media Access Control (MAC)
addresses. If this is the case, why would we configure it with an IP address?
_______________________________________________________________________________________
_______________________________________________________________________________________
Use the following commands to configure S1 with an IP address.
S1 #configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
S1(config)# interface vlan 1
S1(config-if)# ip address 192.168.1.253 255.255.255.0
S1(config-if)# no shutdown
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
S1(config-if)#
S1(config-if)# exit
S1#
Why do you need to enter the no shutdown command?
_______________________________________________________________________________________

Step 2: Configure S2 with an IP addresses.


Use the information in the addressing table to configure S2 with an IP address.

Step 3: Verify the IP address configuration on S1 and S2.


Use the show ip interface brief command to display the IP address and status of the all the switch ports and
interfaces. Alternatively, you can also use the show running-config command.

Step 4: Save configurations for S1 and S2 to NVRAM.


Which command is used to save the configuration file in RAM to NVRAM? ____________________________

Step 5: Verify network connectivity.


Network connectivity can be verified using the ping command. It is very important that connectivity exists
throughout the network. Corrective action must be taken if there is a failure. Ping S1s and S2's IP address
from PC1 and PC2.
a. Click PC1, and then click the Desktop tab.
b. Click Command Prompt.
c.

Ping the IP address for PC2.

d. Ping the IP address for S1.


e. Ping the IP address for S2.
Note: You can also use the same ping command on the switch CLI and on PC2.
All pings should be successful. If your first ping result is 80%, retry; it should now be 100%. You will learn
why a ping may fail the first time later in your studies. If you are unable to ping any of the devices, recheck
your configuration for errors.

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Page 3 of 4

Packet Tracer - Implement Basic Connectivity

Suggested Scoring Rubric


Question
Location

Possible
Points

Part 1: Perform a Basic


Configuration on S1 and S2

Step 3

Step 5

Part 2: Configure the PCs

Step 2b

Step 1, q1

Step 1, q2

Step 4

Questions

12

Packet Tracer Score

88

Total Score

100

Activity Section

Part 3: Configure the Switch


Management Interface

2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public.

Earned
Points

Page 4 of 4

You might also like