Scribd
Upload
73 views

Statequl Physics

This document describes an experiment to determine static equilibrium using a non-concurrent forces apparatus. The purpose is to verify that the sum of torques about any point equals zero and the sum of forces equals zero for a body in equilibrium. The experiment involves suspending weights from the apparatus at varying distances and angles, then measuring to calculate the torques and determine if the sums of clockwise and counterclockwise torques are equal within uncertainty, satisfying the condition for rotational equilibrium. Key results include verifying the theoretical conditions for static equilibrium and using the experiment to calculate the object's center of gravity.

Uploaded by

Emmad Ansari
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
73 views

Statequl Physics

This document describes an experiment to determine static equilibrium using a non-concurrent forces apparatus. The purpose is to verify that the sum of torques about any point equals zero and the sum of forces equals zero for a body in equilibrium. The experiment involves suspending weights from the apparatus at varying distances and angles, then measuring to calculate the torques and determine if the sums of clockwise and counterclockwise torques are equal within uncertainty, satisfying the condition for rotational equilibrium. Key results include verifying the theoretical conditions for static equilibrium and using the experiment to calculate the object's center of gravity.

Uploaded by

Emmad Ansari
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

LPC Physics

Static Equilibrium

Static Equilibrium

Purpose:
To determine that, for a body in equilibrium, the following are true:
The sum of the torques about any point is zero
The sum of forces is zero

Equipment:

Non-Concurrent Forces Apparatus


Hooked Mass Set
Long Rods (3)
Pulleys (2)
Right-Angle Clamps (4)
Table Clamps
Balance
String
Carpenters Level

Theory:
The conditions for the mechanical equilibrium of a rigid body are

F = 0
= 0

(a)
Eq. 1a and b

(b)

That is, the (vector) sums of the forces F and the torques acting on the body are zero.
The first condition, F = 0 , is concerned with translational equilibrium and
ensures that the object is at a particular location (not moving linearly) or that it is moving
1 of 8

LPC Physics

Static Equilibrium

with a uniform velocity (Newtons first law of motion). In this experiment, the rigid
body (the non-concurrent forces apparatus) is restricted from linear motion and F is
automatically satisfied.
To be in static equilibrium, a rigid body must also be in rotational static
equilibrium. Although the sum of the forces on the body may be zero and it is not
moving linearly, it is possible that it may be rotating about some fixed axis of rotation.
However, if the sum of the torques is zero, = 0 , the object is in rotational
equilibrium, and either it dies not rotate (static case) or it rotates with a uniform angular
velocity. (Forces produce linear motion and torques produce rotational motion.)
A torque, or moment of force, results from the application of a force acting at a
distance from an axis of rotation. The magnitude of the torque is equal to the product of
the forces magnitude and the perpendicular distance from the axis of rotation to the
forces line of action, or = Fd (Figure 1). The distance d is called the lever arm or the
moment arm of the force.
Force
Line of action

Axis of rotation
(perpendicular
to plane of
paper)

F
Figure 1
The magnitude of the torque is equal to the product of F and the perpendicular
d from the axis of rotation to the forces line of action = Fd.

Relative to an axis of rotation, a rigid body can rotate in only two directions:
clockwise and counterclockwise. It is therefore customary to refer to clockwise torques
and counterclockwise torques, that is, torques that may produce clockwise rotations and
torques that may produce counterclockwise rotations. For example, in Figure 2, F1 and
F2 produce counterclockwise torques and F3 and F4 produce clockwise torques, but no
rotation would take place if the system were in rotational equilibrium.
d4

d1
d2

d3
50 cm

m1

m2

F1 = m1g

F2 = m2g

m3
F3 = m3g

m4
F4 = m4g

Figure 2
An example of torque in different directions. F1 and F1 give rise to
counterclockwise torques and F3 and F4 to clockwise torques.

The condition for rotational equilibrium is


2 of 8

LPC Physics

Static Equilibrium

cc

+ cw = 0

Eq. 2

where cc and cw are counterclockwise and clockwise torques, respectively. Designating


the directions arbitrarily by plus and minus signs, Eq. 2 can be written

cc

cw = 0
or
cc

= cw

Eq. 3

sum of counterclockwise torques = sum of clockwise torques

For example, for the rod in Figure 2, we have


Clockwise
Counterclockwise
1 + 2 = 3 + 4
or
F1 d 1 + F2 d 2 = F3 d 3 + F4 d 4
The forces are due to weights suspended from the rod. Then, with F = mg,
m1 gd 1 + m2 gd 2 = m3 gd 3 + m4 gd 4
m1 d1 + m2 d 2 = m3 d 3 + m4 d 4

Eq. 4

Center of Gravity and Center of Mass


The gravitational torques due to individual mass particles of a rigid body define what is
known as the bodys center of gravity. The center of gravity is the point of the body
about which the sum of the gravitational torques around an axis through this point is
equal to zero. For example, consider the rod shown in Figure 3. If the rod is visualized
as being made up of individual mass particles and the point of support is selected such
that = 0 , then

or

cc

= cw

(m g )d = (m g )d
i

cc

cw

and
(m1 d1 + m2 d 2 + m3 d 3 + L) cc = (m1 d1 + m2 d 2 + m3 d 3 + L) cw
With the rod in rotational equilibrium, it may be supported by a force equal to its weight,
where the support force is directed through the center of gravity. Hence, it is as though
all of the objects weight (Mg) is concentrated at the center of gravity. That is, if you
were blindfolded and supported an object at its center of gravity on your finger,
weightwise you would not be able to tell if it were perhaps a rod or a block of equal mass.
If an objects weight were concentrated at its center of gravity, so would be its
mass, and we often refer to an objects center of mass instead of center of gravity. These
3 of 8

LPC Physics

Static Equilibrium

points are the same as long as the acceleration due to gravity, g, is constant (uniform
gravitational field). Notice how g can be factored and divided out of the previous
weight equations, leaving mass equations.
Also, it should be evident that for a symmetric object with a uniform mass
distribution, the center of gravity is located at the center of symmetry. For example, if a
rod has a uniform mass distribution, its center of gravity is located at the center of the
rods length. Why?
Center of gravity

m1g

m4g

m4g

m1g

Mg
Figure 3
A rod can be considered as being made up of individual masses in rotational
equilibrium when the vertical support force is directed through the center of gravity

Experiment:
x1 = 0
x2

xcg
mg

m4

m1

c.g

m2

adj.

m3

x3
x4

Figure 4

1. Determine the mass of the non-concurrent force apparatus.


2. Suspend the apparatus horizontally by strings attached to weights, as shown in the
sketch. Weights should not be attached symmetrically.

4 of 8

LPC Physics

Static Equilibrium

3. Adjust weights and the center of gravity adjustment to obtain equilibrium.


4. Measure the distances and angles necessary to determine the torques. Record
uncertainties for all measurements.
5. Remove m2 and m4 and adjust m1 and m3until the apparatus is again horizontal.
6. DO NOT change the center of gravity adjustment. Measure 3 and calculate the center of
gravity.

Analysis:
1. Carefully make a large sketch of the apparatus indicating the forces acting on the
apparatus and their corresponding angles.
2. Assuming the pulleys are frictionless, write Newton's 2nd Law for torques and forces
as applied to the equilibrium of the apparatus.
3. Which of the torques are positive? Calculate each positive torque and its uncertainty.
Add the positive torques to find the total positive torque.
4. Calculate the error in the total positive torque.
5. Repeat Step 3 in the analysis for each negative torque. Calculate the total negative
torque and its uncertainty.
6. Does the absolute value of the total negative torque equal the total positive torque
within the uncertainty? Why or why not?
Note: How would we calculate the uncertainty in sin when the uncertainty in ,
, is known? One way is to calculate:

sin( + ) and sin( - )


i.e., (Sin) =
7.

Sin( + ) - Sin( - )
2

Calculate % difference between positive and negative torques as well as the % uncertainty in your
measurements.

Results:
Write at least one paragraph describing the following:
what you expected to learn about the lab (i.e. what was the reason for conducting
the experiment?)
5 of 8

LPC Physics

Static Equilibrium

your results, and what you learned from them


Think of at least one other experiment might you perform to verify these results
Think of at least one new question or problem that could be answered with the
physics you have learned in this laboratory, or be extrapolated from the ideas in
this laboratory.

The theory section of this lab was shamelessly borrowed from:


Jerry D. Wilson. Physics Laboratory Experiments, 2nd Edition. Lexington MA: D.C. Heath and
Company, 1986. Experiment 13.

6 of 8

LPC Physics

Static Equilibrium

Clean-Up:
Before you can leave the classroom, you must clean up your equipment, and have your
instructor sign below. How you divide clean-up duties between lab members is up to you.
Clean-up involves:
Completely dismantling the experimental setup
Removing tape from anything you put tape on
Drying-off any wet equipment
Putting away equipment in proper boxes (if applicable)
Returning equipment to proper cabinets, or to the cart at the front of the room
Throwing away pieces of string, paper, and other detritus (i.e. your water bottles)
Shutting down the computer
Anything else that needs to be done to return the room to its pristine, pre lab form.

I certify that the equipment used by ________________________ has been cleaned up.
(students name)

______________________________ , _______________.
(instructors name)

(date)

STATIC EQUILIBRIUM
DATA TABLES AND ANALYSIS

7 of 8

LPC Physics

m1

m2

Static Equilibrium

m3

Experimental Equilibrium Data


x1
1
2
3
4

m4

x2

x3

x4

xcg

Net Torque
Positive Torque (+ )

Negative Torque ( )

% Difference

+
( + + )

Error Analysis
% Uncertainty

x1

x2

x3

x4

8 of 8

xcg

+ + 100

You might also like