OCR (A) specifications: 5.4.

1a,b,c,d,e

Chapter 2
Collisions and explosions
Worksheet
Worked examples
Practical: Using the conservation of momentum to
determine the speed of an air-rifle pellet a demonstration
End-of-chapter test
Marking scheme: Worksheet
Marking scheme: End-of-chapter test

Worksheet
Intermediate level
1
2

Define linear momentum and state its SI unit.

Each diagram shows a 2.0 kg object before and after a collision. Calculate the
change in momentum of the object in each case.

[2]

A bumper car collides at right-angles with a metal barrier and rebounds at the
same speed. A student suggests that the change in momentum of the car is zero.
Explain why the student is wrong.
[2]

positive direction

[2]
4.0m s

8.0 ms

[2]
3.0m s1

4.0 ms1

5.0m s1

8.0 ms1

Before

[2]

After

A 0.30 g fly moving at 1.5 m s1 is trapped by a spiders web. The fly comes to rest in
a time of 0.40 s. Calculate the magnitude of:
a

the change in momentum of the fly;

[2]

the average force exerted by the web on the fly.

[3]

A 850 kg cannon fires a 20 kg shell at a velocity of 180 m s1.

a

Calculate the final momentum of the shell.

[2]

What is the magnitude of the momentum of the cannon immediately after the
shell is fired? (You may assume that the cannon is initially at rest.)
[2]

Calculate the recoil velocity V of the cannon.

[3]

The diagram shows two toy trains T and R held in place on a level track against the
force exerted by the compressed spring.
compressed spring

310 g

500 g

When the trains are released, R moves to the right at a speed of 3.8 m s1. The spring
takes 0.25 s to uncoil to its natural length. Calculate:
a

the velocity of train T;

[4]

the average force exerted by the spring on each train.

[4]

2 Collisions and explosions

Cambridge University Press 2005

13

Higher level
7 The diagram below shows the initial state of two trolleys A and B before colliding
and the final state immediately after the collision.
positive direction

4.0m s1

2.5m s1
A

1.0 ms1
B

1.2 kg

0.80 kg

v
A

0.80 kg

1.2 kg

Before

After

Calculate the final velocity v of B.

[4]
1

8 A ball of mass 210 g moving at a speed of 23 m s hits a wall at right-angles and

rebounds at the same speed. The ball is in contact with the wall for 0.31 s.
a

Calculate the change in momentum of the ball.

[2]

Is the momentum of the ball conserved? Explain your answer.

[2]

Calculate the magnitude of the average force acting on the ball.

[3]

9 A bullet of mass 30 g is fired at a speed of 140 m s1 into a stationary block of wood

of mass 460 g. The bullet becomes embedded inside the wood.
a
b
c

Calculate the common speed of the block of wood and the bullet after the
impact.

[4]

Calculate the initial kinetic energy of the bullet and the final kinetic
energy of the block of wood and the embedded bullet.

[3]

Use your answers to b to suggest whether the collision between the bullet and
the block of wood is inelastic or elastic.
[1]

Extension
10 The diagram shows flour falling onto a horizontally moving conveyor.
chute
flour

1.5m s1
conveyor belt

The flour falls vertically onto the conveyor belt at a constant rate of 3.2 kg s1. The
conveyor belt is moving at a constant speed of 1.5 m s1. Calculate the horizontal
force required to keep the belt moving.
[4]

11 A stationary radioactive nucleus of mass M ejects an -particle of mass m at a speed

of 2.0 107 m s1. Given M = 55m, calculate the kinetic energy of the -particle as a
percentage of the final total kinetic energy.
[6]
Total: Score:
59

14

Cambridge University Press 2005

2 Collisions and explosions

Worked examples
Example 1
A car of mass 800 kg is travelling along a level road at a velocity of 4.0 m s1. The driver
presses on the accelerator for a time of 15 s. During this period, a constant force of 400 N
is exerted on the car. Use Newtons second law to determine the final velocity v of the
car. (You may assume that the effect of air resistance is negligible.)
According to Newtons second law:
force =

400 =

change in momentum
time
p
F = t

(800v) (800 4.0)

15

400 15 = 800v 3200

800v = 6000 + 3200
v=

9200
= 11.5 m s1 12 m s1
800

Tip
You may use F = ma and v = u + at to get the answer:
F 400
=
= 0.50 m s2
m 800

a=

v = u + at = 4.0 + (0.50 15) = 11.5 12 m s1

Example 2
The diagram shows two gliders on a linear air track about to collide. After the collision,
the gliders become stuck and move together. Calculate the speed v of the gliders
immediately after the collision. What is the direction of travel after the collision?
Blu-tack
1.5m s

1.2 ms1

200 g

300 g

positive

Momentum is conserved in all collisions. Therefore:

total initial momentum = total final momentum
(0.200 1.5) + (0.300 1.2) = (0.500 v)
0.500v = 0.06
v=

The momentum of the 300 g glider

is negative because it is moving in
the opposite direction.

0.06
= 0.12 m s1
0.500

The minus sign means that after the collision the gliders move to the left.

Tip
When solving problems to do with the conservation of momentum, assign a positive
sign to one of the directions. In the example above:
to the right positive direction
2 Collisions and explosions

Cambridge University Press 2005

15

Practical
Using the conservation of momentum to determine the
speed of an air-rifle pellet a demonstration
Safety
All students should be behind a safety screen. It is also advisable to use a polystyrene
block just in case the shooter (teacher) misses the Plasticine. Teachers and technicians
should follow their school and departmental safety policies and should ensure that the
employers risk assessment has been carried out before undertaking any practical work.

Apparatus

linear air track

air track glider
Plasticine (about 30 g)
10 cm card
light gate

timer
air rifle
digital balance
polystyrene block
safety screen

Introduction
to timer

10 cm card

rifle muzzle

light gate

polystyrene

Plasticine

pellet of mass m
air track

bench

The conservation of linear momentum is discussed on page 13 of Physics 2. This

important principle is used in the experiment described here to determine the speed of
an air-rifle pellet. Secure some Plasticine onto the glider (see diagram). The amount of
Plasticine is such that the fired pellet gets embedded within the Plasticine and does not
come out. According to the principle of conservation of momentum, we have:
initial momentum of pellet = final momentum of pellet and glider (with Plasticine)
Therefore:
mv = (M + m)V
where m is the mass of the pellet, v is the velocity of the pellet from the air rifle, M is
the mass of the glider, card and Plasticine, and V is the common velocity of the glider
and the embedded pellet immediately after the collision.
The speed v of the pellet is given by:
v=

16

M+m
V
m

Cambridge University Press 2005

2 Collisions and explosions

Procedure

Measure the total mass M of the glider (with the card and the Plasticine) and also
the mass m of the pellet.

Ensure the glider is initially at rest. Place the rifle muzzle close to the Plasticine
and fire the pellet.

The glider will travel through the light gate. Record the time t taken for the 10 cm
card to pass through the light gate.

Determine the common speed V of the glider and the embedded pellet using:
V=

Calculate the speed v of the pellet using:

v=

0.10
m s1
t

M+m
V
m

Estimate the uncertainty in your answer for the speed of the pellet.

Guidance for teachers

You can adapt this experiment to determine the speed of a dart fired from a toy gun.

2 Collisions and explosions

Cambridge University Press 2005

17

End-of-chapter test
Answer all questions.

Two cars are involved in a head-on collision.

a

State two quantities conserved in the collision.

[2]

The collision between the cars is described as an inelastic collision. Explain

what is meant by an inelastic collision.

[2]

State Newtons second law.

[1]

A ball of mass 320 g hits the ground at right-angles at a speed of 15 m s1 and

rebounds vertically at a speed of 7.0 m s1. The ball is in contact with the ground
for a time of 0.16 s.
i

Show that the change in momentum of the ball is about 7.0 kg m s1.

[2]

ii

Calculate the average force on the ball during impact with the ground.

[3]

A 2.8 tonne lorry moving at a speed of 30 m s1 collides into the back of a stationary
car of mass 800 kg on the hard shoulder of the motorway. During the collision, the
lorry and the car get tangled together. Calculate:
a

the common speed V of the tangled lorry and car;

[4]

the loss of kinetic energy in the collision.

[3]
1

A bumper car of mass 300 kg moving at 4.0 m s collides with another bumper car
of mass 420 kg moving at 1.5 m s1 in the opposite direction. After the collision, the
speed of the 300 kg car decreases to 0.5 m s1 but it carries on moving in the same
direction (see diagram).
4.0m s1

1.5m s1

0.5 ms1

300 kg

420 kg

300 kg

420 kg

Before

After

Determine the speed v and direction of the 420 kg bumper car after the collision. [4]
Total: Score:
21

18

Cambridge University Press 2005

2 Collisions and explosions

Marking scheme
Worksheet
1

Momentum = mass velocity [1]

SI unit of momentum is kg m s1. [1]

Momentum is a vector quantity it has both direction and magnitude. [1]

If the initial momentum of the car is +p, then its final momentum must be p
(see diagram):
positive direction
Before

barrier

p
After

Change in momentum, p = final momentum initial momentum

p = p p = 2p (the change is not zero) [1]

p = (2.0 8.0) (2.0 4.0) [1];

p = +8.0 kg m s1 [1]

p = (2.0 4.0) (2.0 3.0) [1];

p = 14 kg m s1 [1]

p = (2.0 8.0) (2.0 5.0) [1];

p = +26 kg m s1 [1]

p = final momentum initial momentum

p = 0 (0.30 103 1.5) (the final momentum is zero) [1]
p = 4.5 104 kg m s1 (magnitude only) [1]

Newtons second law: F =

F=

4.5 104
[1];
0.40

p
[1]
t

F = 1.13 103 N 1.1 103 N [1]

p = mv = 20 180 [1]
p = 3.6 103 kg m s1 [1]

The momentum is conserved in this explosion. The momentum of the cannon

is equal in magnitude but opposite in direction to that of the shell. [1]
Momentum of the cannon = 3.6 103 kg m s1 [1]

Using the answer from b, we have:

850 V = 3.6 103 [1]
V=

3.6 103
[1];
850

V 4.2 m s1 [1]

Initial momentum = final momentum [1]

Moving towards the right is taken as the positive direction.
0 = (0.500 3.8) + (0.310 v)
v=

(v is the velocity of T) [1]

0.500 3.8
(the minus sign means that T moves to the left) [1]
0.310

v = 6.13 m s1 6.1 m s1 [1]

2 Collisions and explosions

Cambridge University Press 2005

19

p
F = t [1]
p = 0.500 3.8 = 1.9 kg m s1, t = 0.25 s [1]
1.9
F = 0.25 [1]; F = 7.6 N [1]

7 Initial momentum = final momentum [1]

(1.2 4.0) + (0.80 2.5) = (1.2 1.0) + (0.80 v) [1]
2.80 = 1.20 + 0.80v
v=

2.80 1.20
[1];
0.80

v = 2.0 m s1 (to the right) [1]

8 a p = mv = 0.210 (23 23) (original direction taken as positive) [1]

p = 9.66 kg m s1 9.7 kg m s1 [1]
(The minus implies that the force exerted by the wall on the ball is in the
opposite direction to its initial direction of travel.)
b

The momentum of the ball itself is not conserved. [1]

The total momentum of the wall and the ball is conserved. The wall gains
momentum equal to 9.7 kg m s1 but because it is massive its velocity is
negligible. [1]

F=

p
[1]
t

p = 9.66 kg m s1, t = 0.31 s

F=

9.66
(magnitude only) [1];
0.31

F 31 N [1]

9 a Initial momentum of bullet = final momentum of bullet and block [1]

0.030 140 = 0.490v (final total mass = 460 + 30 = 490 g) [1]
v=

0.030 140
[1];
0.490

v = 8.57 m s1 8.6 m s1 [1]

1 mv2 [1]
Kinetic energy =
2
1 0.030 1402
initial kinetic energy =
= 294 290 J [1]
2
1 0.490 8.572
final kinetic energy =
18 J ( 6% of initial KE) [1]
2

The collision is inelastic because the kinetic energy is not conserved. [1]

10 In a time interval of 1 s we have:

change in the horizontal momentum of the flour p = 3.2 1.5 = 4.8 kg m s1 [2]
t = 1.0 s
p
4.8
Using Newtons second law F = t [1]; so we have F =
= 4.8 N [1]
1.0

20

Cambridge University Press 2005

2 Collisions and explosions

11

Mm
m
V
2.0 107 ms1

Momentum is conserved so pnucleus = p = p [1]

2
1 mv2 and momentum = mv so KE = p
Kinetic energy KE =
2
2m

KE =

p2
[1]
2m

KEnucleus =

p2
p2
p2
1
=
=
2(Mm) 2(551)m 54 2m

( )

KEtotal =

p2 1
p2 55 p2
+
= 54
2m 54 2m
2m

ratio =

p2
KE
=
KEtotal 2m

( )

( )

[1]

[1]

2
55 p
54
= = 0.982 0.98 [1]
54 2m 55

( )

The kinetic energy of the -particle is about 98% of the final total kinetic energy. [1]

2 Collisions and explosions

Cambridge University Press 2005

21

Marking scheme
End-of-chapter test
1

Total energy and momentum are always conserved in a collision. [2]

The total kinetic energy of the cars after the collision is not the same as the
total initial kinetic energy of the cars. [1]
Some of the kinetic energy is transformed to other forms like heat. [1]

The rate of change of momentum of an object is directly proportional to the net

force acting on the object and takes place in the direction of this force. [1]

Momentum, p = mass velocity [1]

p = final momentum initial momentum
p = (0.320 7.0) (0.320 15) [1]
p = 7.04 kg m s1 7.0 kg m s1 (magnitude only)

ii

p
F = t [1]
p = 7.0 kg m s1, t = 0.16 s
7.0
F = 0.16 [1]; F 44 N [1]

Initial momentum of lorry = final momentum of lorry and car [1]

2800 30 = (2800 + 800) V [1]
V=

2800 30
3600

[1]; V = 23.3 m s1 23 m s1 [1]

1 2
Kinetic energy =
2 mv [1]
1 2800 302
1 3600 23.32 [1]
loss in kinetic energy =
2
2
loss in kinetic energy 2.8 105 J [1]

Total initial momentum = total final momentum [1]

(300 4.0) + (420 1.5) = (300 0.5) + (420 v) (positive to the right) [1]
570 = 150 + 420v
v = +1.0 m s1 [1]
The velocity v is positive; therefore the 420 kg car changes direction after the
collision. [1]

22

Cambridge University Press 2005

2 Collisions and explosions