Scribd
Upload
135 views

CX200 Microprocessor Preset Timer-Counter

CX200 Microprocessor Preset Timer-Counter

Uploaded by

Alexander Rios
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
135 views

CX200 Microprocessor Preset Timer-Counter

CX200 Microprocessor Preset Timer-Counter

Uploaded by

Alexander Rios
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

EAGLE SIGNAL brand

Electronic Timers

CX200 Microprocessor Timer/Counter

Microprocessor based
solid state timer/
counter... housed in
CYCL-FLEX case

5
E
L
ET
C I
TM
RE
OR
N ST
I I
CM
E
R
S

RECOGNIZED

The CX200 is a microprocessor based timer/counter housed in a


standard 15 terminal CYCL-FLEX plug-in case. Time or count
operation, time range, and standard or reverse start operation is
selected by 7 miniature rocker switches located inside the unit housing.
Time or count setpoints are entered into the unit using a sealed
membrane keypad on the front of the unit. Each digit in the setpoint is
individually increased or decreased by pressing the appropriate keypad
switch. Time or count setpoint and progress is displayed on the front of
the unit by a 4 1/2 digit liquid crystal display with .5 inch digits. Time or
count subtracts from the setpoint and the output changes state at zero.
Operational mode annunicators also appear in the display area on the
front of the unit. The mode annunciator flashes when the unit is timing
or counting.
Five time ranges from 19.999 sec. to 199 hrs.: 59 min.

CERTIFIED

SPECIFICATIONS
Time/Count Ranges:

Count
Rate

Sym.

Maximum
Range

Minimum
Setting

19999 Cts.

1 Ct.

500/Min. AC.

19999 Cts.

1 Ct.

5000/Min. AC

199.99 Sec.

.01 Sec.

1999.9 Sec.

.1 Sec.

19.999 Sec.

.001 Sec.

199 Min.: 59 Sec.

1 Sec.

199 Hr.: 59 Min.

1 Min.

Two count rates - accept and display counts from 1 to 19999


Two relay outputs - socket mounted for easy replacement
Two form C instantaneous contacts and two form C programmed

contacts
N.O. solid state MOSFET, delayed action switch rated at 1 ampere

continuous load current, 0-264 VAC 50/60 Hz or DC


Ideal output for switching low level signals and high voltage loads

due to MOSFET output's ON resistance of 0.5 ohm and very low


OFF leakage
Programmed outputs operate in one of four load sequences; OOX,

OXO, OOX with pulse output, and OOX pulse output with repeat
cycle operation
Standard start is defined as ON delay reset timer or counter
For standard start units, timer/counter resets on power failure
Reverse start or OFF delay units will not reset on power failure and

will continue cycle when power is restored


Non-volatile memory data retention

Operating Voltage/Frequency: A6 - 120 VAC, 50/60 Hz


B6 - 240 VAC, 50/60 Hz
K6 - 208 VAC, 50/60 Hz
Time Inhibit/Count Line Voltage/Frequency:
A6 - 120 VAC 50/60 Hz
B6 - 240 VAC 50/60 Hz
K6 - 208 VAC 50/60 Hz
Setting Accuracy: Time: 0.1% or 50 ms, whichever is larger (0 to 60C)
Count: 100%
Repeat Accuracy:
Time: 0.001% of setting or 35 ms, whichever is larger (0 to 60C)
Count: 100%
Reset Time: 30 ms following voltage removal from simulated clutch input
(CR1)
Power on Response: 300 ms maximum after voltage applied to terminal 11
Operating Temperature: +32 to +140F (0 to +60C)
Output Rating: Relay: 10 amp (resistive), 120 VAC
Mechanical Life: 20 million operations
Electrical Life: contingent upon controlled load
Solid State: 1 amp, 0-264 VAC, VDC
Vibration: Unit function is unaffected by 2.5G sinusoidal vibration magnitude in both directions of the perpendicular mounting axes imposed from
10 to 100 Hz
Static Discharge: Unit function is unaffected by a constant 3600 volt peak,
60 Hz discharge applied to the grounded front plate at a relative humidity
of less than 25%
Agency Approvals: UL Recognition E96337
CSA Certification LR26861

5.32 DANAHER SENSORS & CONTROLS

CX200 TERMINAL ASSIGNMENTS


2

CR1

TERMINALS AND WIRING DIAGRAM ON REAR


OF TIMER CASE
2

CR1

6
7
*

C
T/ 2
CR

11

12
3

10

11

C
T/ 2
CR

2
CR1

10

1 AMPHERE
SOLID STATE
MOSFET SWITCH

PROGRAMMED
CONTACTS

INSTANTANEOUS
CONTACTS

C
T/ 2
CR

*
A

11
12

*COUNT INPUT/TIME INHIBIT

*COUNT INPUT/TIME INHIBIT

TE
OL
TE T
I
AC M
T
LR E
IO R
ZN S
II
NC

MOUNTING
DRILL AND TAP FOUR
HOLES FOR 8-32 SCREWS
(INCLUDED W/UNIT)

1.406
(35.71)

3.187 + .062
(80.95 + 1.57)
DIA. CUTOUT

G
4.250
(107.95)

3.062
(77.77)

1.406
(35.71)

1.406
(35.71)

MTG. HOLE
USED FOR
GROUNDING
CASE

1.406
(35.71)

3.812
(96.82)

4.125
(104.78)

1.625
(41.27)

5.750
(146.05)

ENCLOSURES

ACCESSORIES

Model No.

NEMA Class

HN308
HN364
HN370

1
1
1A

Description

Model No.

Surface Mtg. with terminal block


Surface Mtg. without terminal block
Dual unit cabinet less unit cases and
toggle switch, with 9 terminal block

H-5331
HP50-31
HP50-131
HP50-133
PDM-534

Description
Mounting Brackets 2 req'd per timer
One Hole Mounting Ring
CYCL-FLEX Water-Sealed Housing
Surface Mounting Adapter to use in place of brackets
1/4 DIN Adapter Plate

ORDERING INFORMATION
CX2
OUTPUT TYPE

02

A6
VOLTAGE & FREQUENCY

Sym.

Description

Sym.

Description

02

10 amp Relay Output

A6

120 VAC, 50/60 Hz

42

1 amp Solid State MOSFET

B6

240 VAC, 50/60 Hz

K6

208 VAC, 50/60 HZ

DANAHER SENSORS & CONTROLS

5.33

You might also like