Scribd
Upload
145 views

Carpentry Terms

This document defines over 50 common carpentry terms used in construction. Some examples include: - Air-Dried Lumber: Lumber dried to 15% moisture content using unheated air. - Anchor Bolts: Bolts driven into concrete to hold structural members in place. - Arch: A curved structure designed to support weight above it. - Beam: A horizontal member supported at ends that carries load across openings. - Framing: The structure of a building made up of studs, beams, headers, rafters and trusses. - Header: A beam above a door or window. - Joist: Parallel framing members that support floors and ceilings.

Uploaded by

Sameh Sameh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
145 views

Carpentry Terms

This document defines over 50 common carpentry terms used in construction. Some examples include: - Air-Dried Lumber: Lumber dried to 15% moisture content using unheated air. - Anchor Bolts: Bolts driven into concrete to hold structural members in place. - Arch: A curved structure designed to support weight above it. - Beam: A horizontal member supported at ends that carries load across openings. - Framing: The structure of a building made up of studs, beams, headers, rafters and trusses. - Header: A beam above a door or window. - Joist: Parallel framing members that support floors and ceilings.

Uploaded by

Sameh Sameh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Carpentry Terms

These carpentry terms are commonly used among carpenters, engineers and architects
during the design and construction of residential and commercial buildings.
Air-Dried Lumber: Lumber that has been dried to a moisture content of approximately
15 percent by unheated air.
Anchor Bolts: Bolts driven into concrete that are used to hold structural members in
place.
Arch: A curved structure designed to support its weight and the load above it.
Apse: A semicircular or polygonal building projection, as of a church.
Areaway: A recessed area below grade to allow for light and ventilation into a basement
window.
Asphalt Shingles: Composition roof shingles made from asphalt impregnated felt
covered with mineral granules.
Astragal: An interior molding attached to one of a pair of doors or window sash in order
to prevent swinging through. It is also used with sliding doors to insure tighter fitting
where doors meet.
Atrium: An open court with a building.
Awning Window: An out swinging window hinged at the top of the sash.
Backfill: Earth used to fill in areas around a foundation.
Balusters: Small vertical supports for the railing of stairs.
Balustrade: A series of balusters supporting the railing of stairs or a balcony.
Bannister: A handrail with supporting posts on a stairway.
Bargeboard: The finish board covering the projecting portion of a gable roof.
Batt: A type of insulation designed to be placed between framing members.
Batten: A strip of wood used to cover the joint between two pieces of siding.

Beam: A horizontal member usually supported on each end by columns or posts. It is


used to carry load across a door, window, or other similar opening.
Bearing Plate: A metal plate that provides support for a structural member.
Bearing Wall: A wall which supports a vertical load in addition to its own weight.
Bench Mark: A mark on some permanent object fixed to the ground from which
measurements and elevations are taken.
Bird's-Mouth: A notch cut on the underside of a rafter to fit it to the top plate.
Buttress: A supporting structure built against a wall.
Cistern: A container for storing water, such as that collected from a rainwater harvesting
system.
Clerestory: A wall with windows that rises above an abutting roofed section of a
building or room.
Concrete Anchor: A lag screw or bolt assembly that is designed to wedge against a predrilled hole in the concrete to attach wood or other material to the concrete slab or
structure.
Cornice: Exterior trim of a structure where the roof and walls meet.
Crow's foot: A carpentry term used to describe a mark, on a piece of wood or other
material, that is defined by two or more lines extending out and originating from one
point (the mark).
Dead Load: The weight of permanent and stationary construction included in a building
(see the Live Load carpentry term).
Engineered Lumber: Lumber made by gluing together veneers of wood to create very
strong framing members.
Fascia: A wood member used for the outer face of a cornice where it is nailed to the ends
of the rafter tails.
Footing: An enlargement at the lower end of a wall, pier, or column, to distribute the load
into the ground.
Framing: The structure of a house, deck or similar structure. Structure is usually made
up of studs, beams, headers, rafters, purlins, and trusses.

Green Building: Design and construction of buildings that minimize impacts of the
environment while helping to keep occupants healthy.
Hammer Drill: Also known as a "rotary hammer" - it provides a short rapid hammering
action to drill through relatively brittle material (like concrete), providing quicker drilling
with less effort.
Header: A type of beam that is used above a door or window.
Hip Rafter: The diagonal rafter that extends from the plate to the ridge for form the hip
of a hip roof.
Jack Rafter: A short rafter usually used on hip roofs.
Joist: One of a series of parallel framing members used to support floors and ceilings.
Ledger: A strip attached to vertical framing or foundation used to support joists or other
horizontal framing.
Live Load: The weight of all moving and variable loads that may be placed upon a
building. (see the Dead Load carpentry term).
Long-Point The part of a beveled cut that is the pointed part. (See the Short-Point
carpentry term).
Nave: The central part of a church from the main entrance to the chancel.
Paddle Bit: A flat-shaped drill bit with a pointed center, designed to drill larger than 1/4"
diameter holes in wood or other material.
Pitch: Inclination or slope, as of roofs or stairs. Rise divided by the span. Usually
expressed as a 5-12 pitch roof, for example.
Plumb: Exactly perpendicular or vertical; at right angles to the horizon or the floor.
Purlin: A structural member used support a group of rafters approximately at the midway
point of the span of the rafters.
Rafter: A structural member that makes up the shape and structure of a roof. The types
include: hip, jack, valley and cripple.
Renewable Energy: Energy produced using solar, wind, hydropower, or biomass energy
sources.
Short-Point: Refers to the part of a beveled cut that is not the pointed part (see longpoint) of the cut.

Stringer: The structural part of stairs that support the risers and treads.
Stud: A structural member typically used to frame walls.
Transept: Either of the two lateral arms of a church built in the shape of a cross.
Transom: A small, often hinged, window above another window or door.
Tread: The step or horizontal member of a stair.
Underpinning: A foundation replacement or reinforcement for temporary braced
supports.
Valley Jack: A rafter that runs from a ridge board to a valley rafter.
Valley Rafter: A rafter that forms the intersection between two sloping roofs.
The definitions of these carpentry terms were obtained from several books and online
sources, including; Webster's Dictionary, Modern Carpentry, Architectural Drafting and
Design, and Architectural Drawing.

You might also like