Scribd
Upload
173 views

Modeling Examples Sharing

The document describes three physical systems: 1. A bus suspension system modeled as a spring-damper system to design a controller that limits oscillations under 5% and settles within 5 seconds. 2. A DC motor system using equations relating torque, current, back EMF and rotational velocity. 3. A cruise control system modeled as a mass-damper system relating force from friction to car speed.

Uploaded by

vinu198500
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
173 views

Modeling Examples Sharing

The document describes three physical systems: 1. A bus suspension system modeled as a spring-damper system to design a controller that limits oscillations under 5% and settles within 5 seconds. 2. A DC motor system using equations relating torque, current, back EMF and rotational velocity. 3. A cruise control system modeled as a mass-damper system relating force from friction to car speed.

Uploaded by

vinu198500
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

itie Knowledge Solutions, Bangalore confidential

2009

1. Bus Suspension System - Physical setup

Designing an automatic suspension system for a bus turns out to be an interesting control
problem. When the suspension system is designed, a 1/4 bus model (one of the four wheels) is
used to simplify the problem to a one dimensional spring-damper system. A diagram of this
system is shown below:

Where:

* body mass (m1) = 2500 kg,


* suspension mass (m2) = 320 kg,
* spring constant of suspension system(k1) = 80,000 N/m,
* spring constant of wheel and tire(k2) = 500,000 N/m,
* damping constant of suspension system(b1) = 350 Ns/m.
* damping constant of wheel and tire(b2) = 15,020 Ns/m.
* control force (u) = force from the controller we are going to design.

Design requirements:

A good bus suspension system should have satisfactory road holding ability, while still providing
comfort when riding over bumps and holes in the road. When the bus is experiencing any road
itie Knowledge Solutions, Bangalore confidential
2009

disturbance (i.e. pot holes, cracks, and uneven pavement),the bus body should not have large
oscillations, and the oscillations should dissipate quickly. Since the distance X1-W is very
difficult to measure, and the deformation of the tire (X2-W) is negligible, we will use the
distance X1-X2 instead of X1-W as the output in our problem. Keep in mind that this is
estimation.

The road disturbance (W) in this problem will be simulated by a step input. This step could
represent the bus coming out of a pothole. We want to design a feedback controller so that the
output (X1-X2) has an overshoot less than 5% and a settling time shorter than 5 seconds. For
example, when the bus runs onto a 10 cm high step, the bus body will oscillate within a range
of +/- 5 mm and return to a smooth ride within 5 seconds.

2. DC Motor Speed modeling - Physical setup

A common actuator in control systems is the DC motor. It directly provides rotary motion and, coupled
with wheels or drums and cables, can provide transitional motion. The electric circuit of the armature
and the free body diagram of the rotor are shown in the following figure:

For this example, we will assume the following values for the physical parameters.

* moment of inertia of the rotor (J) = 0.01 kg.m^2/s^2

* damping ratio of the mechanical system (b) = 0.1 Nms

* electromotive force constant (K=Ke=Kt) = 0.01 Nm/Amp

* electric resistance (R) = 1 ohm

* electric inductance (L) = 0.5 H

* input (V): Source Voltage

* output (theta): position of shaft

* The rotor and shaft are assumed to be rigid


itie Knowledge Solutions, Bangalore confidential
2009

The motor torque, T, is related to the armature current, i, by a constant factor Kt. The back emf,
e, is related to the rotational velocity by the following equations:

In SI units (which we will use), Kt (armature constant) is equal to Ke (motor constant). From the
figure above we can write the following equations based on Newton's law combined with
Kirchhoff's law:

3. Modeling a Cruise Control System

Physical setup and system equations

The model of the cruise control system is relatively simple. If the inertia of the wheels is
neglected, and it is assumed that friction (which is proportional to the car's speed) is what is
opposing the motion of the car, then the problem is reduced to the simple mass and damper
system shown below.

Using Newton's law, the modeling equations for this system become:

itie Knowledge Solutions


#934, 2nd Floor, 17th Main,
Rajajinagar 3rd Block,
Bangalore – 560010
[email protected] www.itie.in
+91.80.23146816

You might also like