OPERATION AND CONTROL OF MULTI-TERMINAL

DC (MTDC) GRIDS

June 2013

Master Thesis
Marta Bobis Ura

Title:
Semester:
Semester theme:
Project period:
ECTS:
Supervisor:
Project group:

Operation and Control of Multi-Terminal DC (MTDC) Grids

10th Semester
Master Thesis
3th February 2013 4th June 2013
30
Sanjay K Chaudhary and Josep Maria Guerrero Zapata
PED4-1048
SYNOPSIS: Europe has many

_____________________________________
Marta Bobis Ura

Copies:
Pages, total:
Supplements:

possibilities
to
generate
renewable energy. A great
example is wind power. Wind
power plants are changing from
point-to-point connection to
multi-terminal network. The
multi-terminal connection will
make easier the transmission
between different countries,
having different grids. This
improvement will also help the
transmission from offshore
wind power plants. To get the
multi-terminal grid it will be
used the VSC-HVDC system,
which is more efficient in long
distances and it has lower
power losses than other
systems. This project aims at
developing the power sharing
control
in
an
MTDC
transmission system.

3
54
3 CDs

By signing this document, each member of the group confirms that all group
members have participated in the project work, and thereby all members are
collectively liable for the contents of the report. Furthermore, all group members
confirm that the report does not include plagiarism.

Abstract
Europe has many possibilities to generate renewable energy. A great example is wind
power, which is a green and efficient resource and, for this reason, the wind power plants
are growing constantly. Wind power plants are changing from point-to-point connection to
multi-terminal network. The multi-terminal connection will make easier the transmission
between different countries, having different grids. This improvement will help the
transmission from offshore wind power plants too. To get the multi-terminal grid it will be
used the VSC-HVDC system, which is more efficient in long distances and it has lower
power losses than other systems.
This project aims at developing the power sharing control in an MTDC transmission system
under normal conditions. The multi-terminal network, the control system and the
simulation studies are modelled in MATLAB/Simulink environment.

Contents
1

INTRODUCTION ..................................................................................................................... 9
1.1
1.2

BACKGROUND........................................................................................................................ 9
STATE-OF-THE-ART ............................................................................................................... 11
1.2.1 HVDC Technology ....................................................................................... 12
1.2.2 MTDC......................................................................................................... 14

1.3
1.4
1.5
2

MOTIVATION....................................................................................................................... 16
PROBLEM DEFINITION............................................................................................................ 16
METHODOLOGY ................................................................................................................... 17

VSC-HVDC AND MTDC SYSTEM........................................................................................... 19

2.1

VOLTAGE SOURCE C ONVERTER................................................................................................ 20

2.1.1 PWM ......................................................................................................... 20
2.1.2 Multilevel ................................................................................................... 21

2.2
2.3
2.4
3

FILTER ................................................................................................................................ 21
DC CABLE ........................................................................................................................... 22
DC CAPACITOR .................................................................................................................... 22

MODELLING AND CONTROL OF MTDC SYSTEM ................................................................. 23

3.1
3.2
3.3
3.4

VOLTAGE SOURCE C ONVERTER................................................................................................ 23

TRANSFORMER..................................................................................................................... 25
DC CABLE ........................................................................................................................... 25
CONTROL............................................................................................................................ 25
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5

Vector control............................................................................................. 25
Phase Lock Loop ......................................................................................... 28
Voltage control........................................................................................... 28
Power control............................................................................................. 30
Droop control ............................................................................................. 32

SIMULATION AND RESULTS ................................................................................................ 35

4.1

THREE TERMINAL MTDC ....................................................................................................... 35

4.1.1 MTDC with Voltage and Power control......................................................... 36
4.1.2 MTDC with Voltage Droop Control ............................................................... 39

4.2
4.3
5

FOUR TERMINAL MTDC ........................................................................................................ 44

FIVE TERMINAL MTDC .......................................................................................................... 47

CONCLUSIONS...................................................................................................................... 51
5.1

FUTURE WORK ..................................................................................................................... 51

List of Figures

Figure 1.1 Global Cumulative Installed Wind Capacity 1996-2012 ......................................... 9

Figure 1.2. Cumulative onshore and offshore wind in the EU (1990-2030). ......................... 10
Figure 1.3 HVDC-HVAC costs.................................................................................................. 11
Figure 1.4 HVDC-HVAC losses. ............................................................................................... 12
Figure 1.5 LCC HVDC. ............................................................................................................. 13
Figure 1.6 VSC HVDC. ............................................................................................................. 13
Figure 1.7 HVDC Supergrid proposal for Europe. .................................................................. 15
Figure 1.8 MTDC..................................................................................................................... 16
Figure 2.1. Bipolar HVDC........................................................................................................ 19
Figure 2.2. Multi-terminal HVDC............................................................................................ 19
Figure 2.3 2-level VSC............................................................................................................. 20
Figure 2.4. 3-level VSC............................................................................................................ 21
Figure 3.1 MTDC..................................................................................................................... 23
Figure 3.2. Comparison. ......................................................................................................... 24
Figure 3.3 PWM...................................................................................................................... 24
Figure 3.4 Output VSC Current. ............................................................................................. 24
Figure 3.5 Three-phase Voltages Transformations................................................................ 26
Figure 3.6 PLL. ....................................................................................................................... 28
Figure 3.7 Voltage controller. ................................................................................................ 28
Figure 3.8 Simplified Voltage Controller. ............................................................................... 29
Figure 3.9 Voltage Regulator Curve. ...................................................................................... 29
Figure 3.10 Active Power Controller. ..................................................................................... 30
Figure 3.11 Simplified Active Power Regulator. .................................................................... 30
Figure 3.12 Active Power Controller Curve............................................................................ 31
Figure 3.13 Reactive Power Regulator................................................................................... 31
Figure 3.14 Simplified Reactive Power Regulator. ................................................................. 32
Figure 3.15 Voltage Droop Controller ................................................................................... 33
Figure 3.16 Droop Controller [19].......................................................................................... 34
Figure 3.17 Droop Controller. ................................................................................................ 34
Figure 4.1 Three MTDC. ......................................................................................................... 36
Figure 4.2 Three MTDC with Voltage and Power Control. .................................................... 37
Figure 4.3 Three MTDC with changed Voltage and Power Control references..................... 38
Figure 4.4 Three MTDC with Droop Control. ......................................................................... 40
Figure 4.5 Three MTDC with Droop Control, changed gain................................................... 41
Figure 4.6 Three MTDC with Droop Control, different DC line impedances. ....................... 43

Figure 4.7 Four MTDC............................................................................................................. 44

Figure 4.8 Four MTDC with Droop Control. ........................................................................... 45
Figure 4.9 Four MTDC with Droop Control, changed DC line impedances. ........................... 46
Figure 4.10 Five MTDC. .......................................................................................................... 47
Figure 4.11 Five MTDC with Droop Control. .......................................................................... 48

Abbreviations
AC
CSC
DC
HVAC
HVDC
IGBT
LCC
MTDC
NPC
OPWM
PLL
PI
PWM
SCC
SPWM
SVPWM
VSC
WPP

Alternative Current
Current Source Converter
Direct Current
High Voltage Alternative Current
High Voltage Direct Current
Insulated Gate Bipolar Transistor
Line Commutated Converter
Multi-Terminal Direct Current
Neutral-Phase Clamped converter
Optimized Pulse Width Modulation
Phase Locked Loop
Proportional Integrator
Pulse Width Modulation
Self Commutated Converter
Sinusoidal Pulse Width Modulation
Space Vector Pulse Width Modulation
Voltage Source Converter
Wind Power Plant

1 Introduction
1.1 Background
Population is increasing, therefore the electricity demand grows too. The depletion
of primary energy sources and the research on renewable energies improve ments make
these grow every year. Besides being clean energies, they have little environmental impact.
Furthermore, they are endless sources of energy and they work with free resources, such
as wind and sun. Another advantage of renewable energies is their geographical situation,
they can be installed in much more places than petroleum, for instance, which exists only
in few countries that control the market. Therefore, thanks to renewable energies some
countries will not depend on other countries in an energy way [1].
An important green energy is wind power, which can generate GW of energy. Wind energy
spread through EU twenty years ago and, although the financial crisis has affected to its
growth, its installations increase annually, as the Figure 1.1 shows.

Figure 1.1 Global Cumulative Installed Wind Capacity 1996-2012 [2].

Nowadays, the 7% of Europes electricity demand is produced by wind energy. Two years
ago, in 2011, this percentage was 6.3% and in 2009 it was 4.8%. It can be seen with this
information how this renewable is expanding. Another fact is that wind energy means 26%
of all EU power capacity installed in 2012 [2].
The future of wind power depends on the continued investigation of progress, because
wind is unpredictable, frequently changing and unclear [3].

A great definition of wind power plant could be a wind energy installation, which has a
large number of turbines and converts the kinetic energy of the wind into electrical energy.
It can difference between two types of wind power plants, the first, which is the most
developed in EU, is onshore and the other one is offshore, which is flourishing more every
year and it is expected to equalize the capacity of onshore parks in some years.
Figure 1.2 represents the forecast of European Wind Energy Association (EWEA) for the
next years, where is observed that it is predicted a continued increase of offshore wind
power. Although offshore plants have high costs, they are being reduced and it causes a
positive prediction for this parks.

Figure 1.2. Cumulative onshore and offshore wind in the EU (1990-2030) [3].

The first offshore wind farm in the world was installed in 1991, months later, t he first
electricity was exported onshore from Vindeby offshore wind farm. It was about 5 MW.
These days, this number is multiplying by 1000, which means 2% of the total wind power
capacity installed in the world. Most of the offshore wind parks, 90%, are situated in the
North, Baltic and Irish Seas and the English Channel. There is a big interest too in Asia and
North America [2].
Offshore parks are growing constantly because they have some advantages over onshore
plants. They have an important disadvantage, which is the cost of the development.
Obviously, the maintenance of offshore plants will cost much more because of their
situation, but the different costs are being studied for their decrease. However, there have
many advantages too. The clearest one is that speed of the offshore wind is higher and
steadier than on land. They have less environmental constraints than onshore. Another
advantage is that offshore plants have typically less turbulence than onshore ones [2].

10

In the following section, the explanation about the suitable system to carry out this task is
discussed.

1.2 State-of-the-Art
HVDC and HVAC are the responsible for transmitting high amounts of energy. It is
discussed in the next paragraphs which is more appropriate.
Although HVDC is not economical for short distances, due to the high cost of the converter
stations, it is more suitable for long distances than HVAC. It is shown in Figure 1.3 the HVDC
and HVAC cost comparison. In this figure, it is observed that HVDC has low costs than HVAC
from a break-even-distance. This distance is, approximately, 600 km, but it is much smaller
for submarine cables, it is less than 100 km [4].

Costs
Total HVAC Cost
Total HVDC Cost

DC Line
Cost

AC Line
Cost

DC Terminal
Cost

AC Terminal
Cost

Break-Even- Distance

Transmission
Distance

Figure 1.3 HVDC-HVAC costs [5].

Another possible comparison between these systems is showed in Figure 1.4. It is observed
that HVAC system has no converter losses when the distance is minimum, however it
increases when the length grows [5]. The break-even distance is the same as in the
previous comparison.

11

Ploss
HVAC
HVDC

Converter
Station Losses

Break-Even- Distance

Transmission
Distance

Figure 1.4 HVDC-HVAC losses.

In addition to have low losses than AC system in long distances, HVDC with bipolar
configuration can transmit the energy using two cables instead the needed three of AC.
This fact means that HVDC costs less than HVAC when the length is important. Another
important advantage over HVAC is that HVDC system is able to connect asynchronous AC
network.
Even though HVDC system has some disadvantages comparing it with the traditional HVAC,
the main advantages to choose this DC system are having neither reactance, nor stability
problem and therefore no distance limitation. Being HVDC perfect for transmitting
electricity over great distances [4].
In conclusion, today the more appropriate system to transmit this amount of energy from
offshore to onshore is HVDC system. It presents many advantages and is the reason why is
used in more projects every year.

1.2.1 HVDC Technology

Otherwise, the main component of HVDC system is its converter. Depending on the
type of the converter HVDC system can be classified as HVDC Classic or Light.
On the one hand, HVDC Classic works with conventional Line Commutated Converter
(LCC), in other words, conventional HVDC uses Line Commutated Current Source
Converter (CSC). Thyristor valves are utilized in this trans mission. This system has
lower cost and less station losses than VSC HVDC [7].

12

A back-to-back LCC scheme is showed in Figure 1.5.

Figure 1.5 LCC HVDC.

On the other hand, HVDC Light works with Self Commutated Converter (SCC), that is,
Voltage Source Converter (VSC) with PWM. VSC HVDC utilizes self-commutated
transistors, IGBT, instead thyristors. An important characteristic which should be
considered is the ease of incorporating new VSC-HVDC terminals to an existing MTDC
system. Furthermore, VSC systems have the benefit that the DC voltage polarity
remains the same when there is a power reversal. VSC-HVDC is presented in Figure
1.6.

Figure 1.6 VSC HVDC.

The IGBTs has the advantage, over using thyristors, of turn off capability, giving the
converter another degree of freedom and making the VSC self-commutated. The
IGBT devices could be controlled at any moment unlike thyristors.
Both systems have advantages and disadvantages over the other one, but, in this
case, VSC will be the choice, due to the previous mentioned advantages and the fact
that VSC-HVDC can control independently the active and reactive power, while CSC
cannot do that [8].

13

1.2.2 MTDC
Another important point in HVDC systems is their connection. Most projects about
HVDC systems are two terminals, point to point connection, but the term of
supergrid exists. It would be a large network that transmits high amounts of
renewable energy to different places, located at a great distance.
There are many reasons to build a Multi-terminal HVDC, instead having several
separate point to point transmissions. The main advantage is that MTDC will improve
the functionality and reliability of the network, decreasing conversion losses and with
less cost [9].
MTDC is more efficient than a point-to-point connection. It allows having multiple AC
grids and in case that one AC link breaks, MTDC will have other grids to deliver the
energy, unlike point-to-point, which only has one AC grid and if some problem
happens it will make that all the network fails.
MTDC is interesting for offshore wind transmission, considering that VSCs have a
limited transmission capacity and offshore wind farms have separate locations in the
wind area, because MTDC can take out and deliver power from and to different
terminals [10].
Some projects like the Kriegers Flak (the Baltic Sea) and the Tres Amigas (USA) are
being developed. These two projects have the same purpose, working in different
environments. The first one is working with offshore wind power and the Tres Amigas
project works with onshore wind power, apart from solar and geothermal. This is a
great example to show that MTDC, based in VSC, is suitable for any condition.
The objectives of Kriegers Flak are connecting the new offshore wind turbines to the
power network and interconnect the power grids of Denmark and Germany. The
benefits of an offshore power grid are, among others, improving renewable energy
utilization and national economies, because although when the wind turbines deliver
limited power, the power grid can be used. In this project, HVDC is used due to the
German and Danish systems are not synchronous, to make a connection between
them DC is needed [11].
Kriegers Flak is the step before a greater project in the North Sea, where a much
larger MTDC offshore power grid is planned. This could help to the fossil fuel
independence in Europe.
In Germany is planned another example of MTDC. It consists of transmit the offshore
energy of the Baltic Sea across the country and delivering electricity in the south,
which depends more on nuclear energy. In this manner, the rest nuclear reactors of
this country could be closed, having an energy alternative [12].
These projects will be the predecessors of the European Supergrid, which is explained
in the following paragraph.

14

Another project proposal is shown in Figure 1.7. It is based on a supergrid, consisting

of VSC-MTDC, connecting and integrating different separated wind farms across
Europe. This project would provide many benefits to the EU members, being a great
improvement in the energy needs of Europe. The energy could be delivered where it
would be needed through the internal network, transmitting it from the offshore grid
to the continental Europe. This proposal is extensively described in literature [13].

Figure 1.7 HVDC Supergrid proposal for Europe [13].

15

1.3 Motivation
The North Sea, the Baltic and the seas around United Kingdom and Ireland has a huge
potential for the offshore wind power generation. Similarly, the southern Europe and
northern Africa has a large potential for the solar power generation. It is proposed that a
Multi-Terminal DC Supergrid overlay could be developed to facilitate GWs of power
throughout the European Grid from the offshore wind parks to the continental Europe.
In this project it is intended to simulate a three-terminal HVDC, trying to find how this
system works and hence, having an idea of how the future MTDC supergrid would work.

1.4 Problem definition

A multi-terminal DC with three terminals is designed to its simulation and control. The
model can be seen in the Figure 1.8.

VSC
GRID

DC LINE

WPP

VSC

VSC
GRID

Figure 1.8 MTDC.

The scheme consists of two onshore terminals, which are connected to the grid, being
responsible to transmit the alternative current to other load centers, and the third
terminal, which receives the energy from the wind power plant. The three terminals are
communicated by a DC line. Otherwise, there is a converter in each terminal, it transforms
the current from DC to AC in the onshore terminals or AC to DC in the offshore.
On the other hand, this MTDC will be controlled by Voltage and Power Controllers.
Once the system is controlled, it will be simulated, obtaining the final results.

16

1.5 Methodology
The first step carried out was reading literature. Many documents have been read to make
this project. Some of them are reports of important institutions, power systems books,
papers of other projects and publications of IEEE.
MATLAB/Simulink, was used for modeling and simulation. The system was developed from
the beginning, solving different errors, simplifying the parts that were not too important
and focusing on the scope, which was to get the correct running of a three terminal MTDC.
Subsequently, the control for this system was designed. Firstly, two different regulators
were separately implemented in two terminals. After their proper operation, they were
replaced for a more complete droop controller.
Lastly, the simulation of the entire system was tested by Simulink tool, obtaining some
results, which were compared with the expectations.

17

18

2 VSC-HVDC and MTDC System

The selected system to get across the energy from offshore to onshore is HVDC. It
has several features for carrying out this task. First of all, it is appropriate for long
distances, which is perfect to transmit energy from an offshore park to land or from
onshore to load centers, for instance. It can use overhead lines and subsea or underground
cables, being environmentally friendly. Another quality is that this system tolerates large
amounts of electrical power and asynchronous interconnections. Apart from the previous
features, it has low losses in long distances than other systems, HVAC for example. All
these characteristics are the reasons why HVDC projects are increasing every time [14][15].
HVDC system can have different configurations. When this configuration consists of
more than two terminals, it is called Multi-Terminal DC (MTDC). Figure 2.1 shows a Bipolar
HVDC configuration and Figure 2.2 a Bipolar MTDC.

~
=

Figure 2.1. Bipolar HVDC.

~
=

Figure 2.2. Multi-terminal HVDC.

Multi-terminal HVDC system have more than two converter stations, in this example there
are three converter stations, which are interconnected in the DC side of the transmission
system.

19

2.1 Voltage Source Converter

This converter transforms the direct current in alternative current. If the
conversion is DC to AC is called inverter and rectifier when the transformation is AC to DC.
Figure 2.3 represents a two-level, three-phase Voltage Source Converter. As we can
observe it is formed by two transistors per phase with an anti-parallel diode.

Figure 2.3 2-level VSC

2.1.1 PWM
It is usually used to control the input of electrical devices, in this case, the input signal
of the IGBTs. There are different types of PWM used for the IGBTs of the VSC, like
Optimized PWM (OPWM), Space Vector PWM (SVPWM) and the simplest Sinusoidal
PWM (SPWM) [16].
Sinusoidal PWM is a modulation technique that forms the width pulse of a signal by
comparing a triangle waveform with the modular signal. This PWM is used in this
project.

20

2.1.2 Multilevel
Apart from the 2-level VSC presented before, there are differe nt multi-level
converters, which are suitable to HVDC system too. A known 3-level VSC is showed in
Figure 2.4.

Figure 2.4. 3-level VSC

This three-level VSC is called Neutral-Point Clamped (NPC). The number of seriesconnected switches is reduced by NPC. Each switch cell of this system has to resist
half of the DC voltage, hence it can be reduced the switches in series. Furthermore,
comparing the two-level VSC with this NPC, the three-level system can produce a
three-phase AC voltage with a lower harmonic distortion. It is explained extensively
in literature [17].

2.2 Filter
The filter is situated after the converter and before the grid. Its main function is to
diminish the high frequency harmonics.
The voltage of the grid is measured in this filter.

21

2.3 DC Cable
DC cable will connect the different parts that belong to direct current. It has
usually a resistance in its line.
We can compare HVDC cable with traditional AC cable and we will notice that it has many
advantages. DC cable has lower losses, it does not need an intermediate station, it neither
has increasing of the capacitance in the AC network, nor limit on the cable length. AC
cable does have limit in the length because of the cable capacitance and AC transmission
needs an intermediate station to compensate the reactive power [15].

2.4 DC Capacitor
DC voltage has small ripples when a DC capacitor is implemented. This ripple is produced
by the switching actions of the converter. The DC capacitor has to be a medium size to be
able to diminish the ripple and to permit normal speed responses.

22

3 Modelling and Control of MTDC System

A three-terminal MTDC will be design in this project. Two terminals are the onshore
plants, with grid connection. The other te rminal is the offshore plant. It can be observed
the described system in Figure 3.1.

DC LINE
HVDC

HVDC

HVDC

Figure 3.1 MTDC.

Bipolar HVDC system is used, this means that one line is for positive and the other one for
negative. In the model it is represented only by one line and ground. In this project, it is
used ground, because the DC line has the double value of inductance and resistance,
instead having two single values in positive and negative lines.

3.1 Voltage Source Converter

The VSC of this project is three-phase, two-level converter. First of all, it is created
the gate pulse for the IGBTs. The chosen PWM between those described in the previous
chapter is pure Sinusoidal PWM.
Figure 3.2 shows the comparison of the sinusoidal reference with the t riangular wave,
obtaining the switching pulse of Figure 3.3. This pulse is different depending on the chosen
three-phase sinusoidal wave, they are 120 phase-shifted. Using the different signal pulses
in the gates of the IGBTs, in the Figure 2.3, it can get the output of the converter, it is
represented in Figure 3.4.

23

Figure 3.2. Comparison.

Figure 3.3 PWM.

Figure 3.4 Output VSC Current.

24

The scope of this project is not this VSC, hence it is simplified the circuit replacing the VSC
and the PWM for three current sources, which have the same output as the previous
converter.

3.2 Transformer
The objective of the transformer is adapting the signal of the converter to the grid, besides
giving galvanic isolation. In this project the transformer is considered ideal, there are no
losses, therefore in its place an inductance in series with a resistance are put.

3.3 DC Cable
In the description it is written that the DC cable connects the DC parts, in this project these
are the output of the rectifier, in the offshore plant, and the input of the inverters, which
are part of the onshore park.
To simulate the DC cable resistance, the DC line has a resistance in series with an
inductance.

3.4 Control
In this chapter the different utilized controllers for VSC-HVDC are explained.

3.4.1 Vector control

Vector control is the most basic and the most used control for VSC. This control
transforms the currents and the voltages into d-q reference frame, it will be
synchronized by the PLL [18].
The Figure 3.5 represents the three phase voltage transformations.
The transformation can be done by Clarke method. It turn abc into
and then
into dq. Otherwise, the abc-to-dq transformation and vice versa could be done
directly by the transformation of Park.

25

B
V

Vref

Vq

Vd

A
t+

Figure 3.5 Three-phase Voltages Transformations.

The AC voltages are defined in the following equations (1).

(1)
Calculating the
it can be seen that Clarke gives the components along
(2) and Park along the synchronously rotating dq-axes (3).

-axes

(2)

(3)

26

In this control, it is aligned the dq-axis in such direction that the d-axis is in phase
with the AC grid. Hence, it is achieved the following statement (4).

(4)
The transformation of Park is done in this project to turn AC currents and voltages
into dq components, i.e. abc-to-dq. To achieve that, the next operation is done (5),
knowing that
.

(5)
To obtain the dq-abc transformation, the inverse transformation of Park is carried
out by (6).

(6)

27

3.4.2 Phase Lock Loop

Frequency is measured by the PLL, obtaining the angular frequency, which will be
used in the dq-to-abc and the abc-to-dq transformation as the reference. The PLL
synchronize the output voltage of the converter with the grid.
Figure 3.6 shows the scheme of PLL.

abc

Vabc

dq

PI

mod

wt

PLL

Figure 3.6 PLL.

3.4.3 Voltage control

Observing the Figure 3.7 it can be seen that the error of voltage is calculated by
, that is, the difference between the voltage reference and the voltage of
the DC side, measured in the DC capacitor. This error is passed through a
proportional integrator (PI) and the result is
, the reference of the d-axis current
component [19].
inner current control

Vd
V*DC

+VDC

PI

id*

+id

Figure 3.7 Voltage controller.

28

PI

-+Liq

Vdconv

Otherwise,
and
are the d-axis components of current and voltage, respectively, of the
AC side. is the q-axis current component of the grid.
Furthermore,

is the converter transformer reactance.

The model of the Figure 3.7 is simplified, due to the inner control loop in this project
is considered ideal. The result, which is built in the project, is represented in Figure
3.8.

V*
DC

id*

PI

+VDC

Figure 3.8 Simplified Voltage Controller.

Figure 3.9 Voltage Regulator Curve [20]Figure

3.9 shows the characteristic curve of the DC

voltage regulation of VSC-HVDC. The DC voltage controller maintains the DC voltage
constant.

VDC
V*DC
Inverter
mode

Rectifier
mode

P
Figure 3.9 Voltage Regulator Curve [20].

29

3.4.4 Power control

The Figure 3.10 resembles Figure 3.7. They follow the same process, although in this
case the power error is calculated by
, the difference between the active
power reference and the active power of the system. Active power is calculated as
follows (7).

(7)

inner current control

Vd
P*

+-

PI

id*

PI

+-

-+-

Vdconv

Liq

id
Figure 3.10 Active Power Controller.

The inner current control, as it was mentioned earlier, is considered ideal. Therefore,
the simplified and designed power regulator is the same as the one represented in
Figure 3.11.

P*

+-

PI

id*

P
Figure 3.11 Simplified Active Power Regulator.

30

The power regulator curve is represented in Figure 3.12, it shows the relation
between the DC voltage and the power. It can be seen that the power keeps
constant.

VDC

Inverter
mode

Rectifier
mode

P
P*
Figure 3.12 Active Power Controll er Curve.

In this project reactive power becomes zero, therefore

. However, if a reactive
power controller is designed, it would be the demonstrated in Figure 3.13. The
would be the reactive power reference and
would be the calculated reactive
power, its value is calculated by the following equation (8).

(8)

Another difference is

, which are the q-axis component of voltage of the AC side.

inner current control

Vq
Q*

+Q

PI

iq*

+-

PI

iq

+
-+

Vqconv

Lid

Figure 3.13 Reactive Power Regulator.

31

The regulator is simplified as the Figure 3.14 shows.

Q*

+-

PI

iq*

Q
Figure 3.14 Simplified Reactive Power Regulator.

3.4.5 Droop control

Once the power and voltage controllers worked, they were changed for the droop
control, which regulate both power and voltage. There was a power controller in one
terminal and a voltage controller in other, but it is not desirable. It is not appropriate
that only one terminal regulate the voltage in a MTDC. The reason for this change is
that fact.
The droop regulator is a combination of the previous controllers, getting a droop
balance between voltage and power.
The scheme of the droop regulator is represented in Figure 3.15.

32

P
P*

+--

PI

id*

1
DC

V*DC

+-

VDC

Figure 3.15 Voltage Droop Controller [19].

The gain of this regulator is

, the next equation is used to calculate it (9).

(9)

This gain will be the reference to obtain the slope in the relation between voltage
and active power. There are different slopes, depending on the sign of the
. These
options are represented in Figure 3.16 and Figure 3.17.

33

VDC
Slope=

V*DC
Inverter
mode

dc

Rectifier
mode

P
P*
Figure 3.16 Droop Controller [19].

In this project, Figure 3.16 represents how the system works and Figure 3.17 is the
droop controller designed for the system. The regulator gets that when the power is
decreasing the voltage will diminish its value too and if the power increases, the
voltage will grow too.

VDC
Slope=

dc

V*DC
Rectifier
mode

Inverter
mode

P
P*
Figure 3.17 Droop Controller.

34

4 Simulation and results

The MTDC model designed before is testing in this chapter. Its simulation will be
carried out with different regulators.
First of all, voltage and active power controllers were designed and tested. To improve the
control of the MTDC they were replaced for voltage droop control. This new regulator was
installed in each terminal to control both active power and voltage at the same time.
As the wind is not constant, it usually changes during time and it has different amplitudes,
a pulse generator is included in the offshore stations, in the left side of the schemes. In this
manner, the wind variations can be simulated. This pulse generator changes every 5
seconds with an amplitude of 0.2. In the case of MTDC of four and five terminals there are
two pulses blocks, the second one is delayed 2.5 seconds in relation to the first offshore
station and the wind has 0.1 more amplitude.
Moreover, to simulate the different MTDC systems the voltage and power references are
determined. They are needed to the proper operation of the controllers. The voltage
reference is
and the active power reference is
Depending on the station
the power reference will change, having
or
Some results are expected. The power control should maintain constant the power value in
its reference, independently of the offshore station changes. Otherwise, the voltage
control should get the reference as the final voltage value, although there are some
increases or decreases in the delivery station. On the other hand, the droop control should
get the power sharing between the different onshore stations.
To verify the awaited results there will be some study cases. The first case is three MTDC
with separated voltage and power control, the next is three MTDC with droop control. And
the last study cases are three and four terminal MTDC with droop control. In each study
case, the DC line length, the power reference and the gain of the droop control, when it is
implemented, change to different values to observe how the response of the system is.

4.1 Three terminal MTDC

The first simulated model is the three-terminal MTDC with separated voltage and
power control. Terminal 1, HVDC1 in Figure 4.1, has the voltage controller of this model,
while Terminal 2, HVDC2, controls the active power.
In the second case, HVDC1 and HVDC2 have the same regulator, voltage droop controller.

35

DC LINE
HVDC2
WPP

HVDC3

HVDC1

Figure 4.1 Three MTDC.

After the explanation of both systems and their graphic results , they are compared with
each other to verify that droop control improves the response of the system.

4.1.1 MTDC with Voltage and Power control

Figure 4.2 show the DC current, the DC voltage and the power of this system. Voltage
and current are measured in the DC capacitor of each HVDC.
The legend of the figures has three terminals. HVDC1 and HVDC2 are the onshore
stations, while HVDC3 is the offshore plant, where the wind is varying.
HVDC3 has some DC line impedance, HVDC1 has the double of this impedance and
HVDC2 the triple. Furthermore, HVDC3 has
power reference, HVDC2 has in its
power reference
and HVDC1
voltage reference.
It is observed in Figure 4.2 that the HVDC1 voltage reacts to the power change, but
after some seconds the system achieve the reference voltage value that it had again.
That means that the voltage regulator is working properly in this station. Otherwise,
the voltage value of HVDC2 changes, the reason is that it has no voltage controller.
However, HVDC2 maintain its reference power value. When the power is steady, it
has no changes. This fact shows that the active power control helps to keep it
constant. The same situation than before is occurring, HVDC1 has no power control,
therefore its value is modified when the wind changes.

36

HVDC3 power is in its reference. It vary

1 pu, has
and the lower value,

in amplitude, when it is in its higher value,

is
.

On the other hand, if the DC Current is observed, it is confirmed that the system is
doing its work. The waveforms are the same as the power responses and its values
fulfill the division of power over voltage.
DC Current
800
600
400
200
0
-200

6.5

10

12

10

12

10

12

DC Voltage

x 10

6.45
6.4
6.35
6.3

6
Power

x 10

3
2
1
0
-1
0

4
HVDC1

6
HVDC2

HVDC3

Figure 4.2 Three MTDC with Voltage and Power Control .

37

If the DC line is changed, making it longer, the results are similar to the ones in Figure
4.2. The voltage decreases
and it is compensated with the power. The system
would have more losses, but HVDC1 maintains its voltage reference value and HVDC2
its power reference. This fact shows that the controllers are working properly.
It is observed in Figure 4.3 what happen if the reference values change. Voltage
reference in HVDC1 was increased to
, while power reference in HVDC2
changed to
.
DC Current
500

-500

10

12

10

12

10

12

DC Voltage

x 10

8.8
8.6
8.4
8.2
8

6
Power

x 10

2
0
-2
-4

4
HVDC1

6
HVDC2

HVDC3

Figure 4.3 Three MTDC with changed Voltage and Power Control references .

38

The controllers maintain the reference value of power, in the case of HVDC2, and the
voltage reference value in HVDC1.
It can be seen in Figure 4.3 that the HVDC1 power decreases, the reason is that
HVDC1 compensates the power increase of HVDC2. The same is happening with the
current. Otherwise, the voltage grows, HVDC1 keep constant its voltage in its
reference value.
In the 7 second it is observed that the power reference value of HVDC2 and HVDC3
are the same, it means that there is no power for HVDC1, which is represents by its
near 0 value.
In conclusion, both regulators are working correctly.

4.1.2 MTDC with Voltage Droop Control

The next simulated scheme is three-terminal MTDC, but it has droop control instead
separated voltage and power regulators. In the following graphics it is observed how
voltage and power are balanced because of the droop control.
As in the previous section, HVDC1 and HVDC2 are the onshore plants and HVDC3 is
the offshore station.
HVDC3 has the same DC line resistance than in the previous section, HVDC1 has the
double, but HVDC2 now has four times this impedance. In this model, the power
reference of the offshore station, HVDC3, is
, HVDC2 has in its power reference
and HVDC1
.
is the voltage reference in both onshore stations.
When offshore power varies, consequently voltage and power in HVDC1 and HVDC2
change too and, therefore, currents. Both power and voltage changes are sharing
equally into the different stations. It is observed in the Figure 4.4 that power
decreases
in HVDC3, this power droop is sharing between HVDC1 and
HVDC2, diminishing their power in
each.

39

DC Current
500
400
300
200
100
0
-100

6.5

10

12

10

12

10

12

DC Voltage

x 10

6.4

6.3

6.2

6.1

Power

x 10

-1

4
HVDC1

6
HVDC2

HVDC3

Figure 4.4 Three MTDC with Droop Control .

40

Keeping the same DC lines values, the gain of the HVDC2 droop control is four times
the gain of the HVDC1. The results are showed in Figure 4.5.
DC Current
500
400
300
200
100
0
-100

6.45

10

12

10

12

10

12

DC Voltage

x 10

6.4
6.35
6.3
6.25
6.2

6
Power

x 10

2
1
0
-1

4
HVDC1

6
HVDC2

HVDC3

Figure 4.5 Three MTDC with Droop Control, changed gain.

41

It can be observed in Figure 4.5 how the droop voltage and power is different shared
in this case. The fact that the gain of the HVDC2 droop control is four times the gain
of HVDC1 affects to the droops. The droop of the offshore station is shared between
the onshore terminals, but this time HVDC2 will have more droop power. The HVDC2
power droop will be four times larger than the one in HVDC1.
The conclusion was the same, testing with different droop gains, as much as the gain
of the droop control increases, as much as the droop power decreases.
In Figure 4.5 it also can be seen that the variation of the power is compensated by
the voltage, where HVDC1 has more voltage droop than HVDC2, around four times.
The next case is represented in Figure 4.6. HVDC1 and HVDC2 return to have the
same gain in the droop control. However, the HVDC1 DC Line is decreased to 1.1
times the HVDC3, while HVDC2 is decreased to three times this impedance.
The decrease in the DC Line of HVDC2 is higher than in HVDC1. It can be seen that the
current of HVDC2 diminishes its value, hence power also get low and the droop
control causes the reduction of the voltage. To compensate this decrease, HVDC1 has
to increases its values.
In this last case, the difference is not greater, but if the change in the DC Line is more
different, the decreases or increaser will be higher.
Another change implemented in the model was increasing the power reference of
the stations. If the reference rises, the higher steady value of the stations also grows
and vice versa.

42

DC Current
500
400
300
200
100
0
-100

6.5

10

12

10

12

10

12

DC Voltage

x 10

6.4
6.3
6.2
6.1

6
Power

x 10

2
1
0
-1

4
HVDC1

6
HVDC2

HVDC3

Figure 4.6 Three MTDC with Droop Control, different DC line impedances.

43

In conclusion, droop control is a better choice when there are more than two terminals. It
makes equal the voltage droop and the power change of each station. This control
operates sharing the power between the different onshore plants, getting a balance
between voltage and power.
If an unexpected change in power flow happens in some terminal, the droop control will
compensate for the power unbalance through the rest terminals.

4.2 Four terminal MTDC

In this model a forth terminal is included as an offshore station, HVDC4. It has
another pulse generator with amplitude of 0.3 and it changes every 5 seconds, but
this station has a delay of 2.5 seconds. In this manner, HVDC4 changes first at 2.5
seconds and then at 7.5, while HVDC3 do it at 5 and 10 seconds.
Figure 4.7 represents the scheme of this model.

WPP

DC LINE
HVDC2

HVDC3

WPP

HVDC4
HVDC1

Figure 4.7 Four MTDC.

It can be seen in Figure 4.8 the obtained results. Observing the power graphic, the first
change is produced in HVDC4 at 2.5 seconds, it causes that HVDC1 and HVDC2 also change,
in this case, increasing their value. In this study the gain of the droop controllers are the
same, thus the growth is equally distributed in both terminals, that is, half of the HVDC4
increase. At 5 seconds, HVDC3 decreases its value, hence HVDC1 and HVDC2 diminish
theirs too. Once again, HVDC4 at 7.5 seconds decrease, then HVDC1 and HVDC2 reduce

44

more. Droop controller is working properly, due to the correct power sharing between
terminals.
The voltages of HVDC1 and HVDC2 decrease when the power reduces its value, because of
the droop controller action. The voltages of the offshore stations are forced to do the same
than the onshore terminals, due to the shared DC line.
DC Current
800
600
400
200
0
-200

6.55

10

12

10

12

10

12

DC Voltage

x 10

6.5
6.45
6.4
6.35

6
Power

x 10

4
3
2
1
0
-1

2
HVDC1

6
HVDC2

HVDC3

HVDC4

Figure 4.8 Four MTDC with Droop Control.

45

If the DC line of HVDC1 and HVDC2 are increased, maintaining the offshore in the same
value, growing four times and twice, respectively, in relation to the offshore, final results
change, as it can be observed in Figure 4.9.

DC Current
800
600
400
200
0
-200

6.65

10

12

10

12

10

12

DC Voltage

x 10

6.6
6.55
6.5
6.45
6.4
6.35

6
Power

x 10

4
3
2
1
0
-1

2
HVDC1

6
HVDC2

HVDC3

HVDC4

Figure 4.9 Four MTDC with Droop Control, changed DC line impedances.

46

In this case, HVDC1 reduce its power, due to the growth of the line and its power reference
value, hence the voltage diminish, caused by the droop control, and therefore the current.
To compensate de unbalanced power, HVDC2 power increases and the voltage of all the
stations is higher.
If the gain of the droop controllers is changed, it would happen the same than in the
previous section. The station which has the higher droop gain value will have a larger droop
in the power, as high as the equivalence of times in relation with the other droop
controller. As a consequence, voltage would compensate this, having a larger voltage
droop the station with lower droop gain.

4.3 Five terminal MTDC

This model has a new fifth onshore terminal, the rest is the same as in the previous section.
The model is showed in Figure 4.10.

DC LINE
HVDC2
WPP

HVDC3

HVDC5
WPP

HVDC4

HVDC1

Figure 4.10 Five MTDC.

47

DC Current
800
600
400
200
0
-200

6.5

10

12

10

12

10

12

DC Voltage

x 10

6.45

6.4

6.35
0

6
Power

x 10

4
3
2
1
0
-1

2
HVDC1

4
HVDC2

6
HVDC3

Figure 4.11 Five MTDC with Droop Control.

48

HVDC4

HVDC5

These results are similar to the obtained in the previous section. The difference is that an
onshore terminal is added. The droop control works correctly, sharing the power equitably
between the different onshore terminals and forcing the voltage to decrease when the
power diminish its value.
The outcome of changing the droop controller gain is the same than in the other studies, if
some station has more gain value than others, it will have more power droop and less
voltage droop.
DC lines values were increased and in HVDC1 station, which has the higher power
reference and DC line impedance, the power diminishes, thus the current and therefore
the voltage by the droop controller. The rest stations compensate this decrease with their
voltage and power growth.

49

50

5 Conclusions
Nowadays, MTDC is considered in many future projects, based on VSC-HVDC technology. A
Multi-terminal DC was developed in this project, it consists of three terminals, two of them
are onshore stations, while the third is an offshore wind farm. Different controllers were
implemented to this model and, afterwards, simulated. Furthermore, two more terminals
were added to confirm the correct operation of the system. Based on the results, some
conclusions can be stated.
Voltage and power controllers maintain the given reference value, regardless dynamic
problems in other stations or abnormal conditions.
The droop control works properly, even when the DC lines impedances, the power and
voltage references of the converter or the gain of the droop control are changed.
Conforming with the slope of the regulator, achieving the decrease of the voltage when the
power is reducing and vice versa.
The addition of more terminals does not affect to the control of other stations, being
unnecessary add more controllers or modifying the model.

5.1 Future work

More realistic models
In this project, to focus in the scope many components have been simplified, considering
them ideal or building the average model. The scope was observing the working of the
entire MTDC, hence some systems, like the converter or the transformer were simplified.
To get an improved and more real model, these simplified systems have to be replaced for
the entire model, keeping in mind their losses, their disturbances and their problems. In
this manner, a more real operation of MTDC would be observed.

Real simulation
Once the realistic model is implemented it could be simulated to get more real results. It
could be simulated in different environments than MATLAB/Simulink, where disturbances
and extremely changes of the wind could be introduced.

51

Dspace
Dspace is a tool where the controllers can be changed in real time, they can be tuned until
getting the expected outcomes and it is possible improving the final results using this tool.

Adaptive droop control

To improve the droop control implemented in the project an adaptive control could be
designed. This adaptive controller is built to ensure that all the converters participate in
power sharing, depending on their ratings and the difference between the rated capacity
and the present loading available, under every operating condition. Unlike fixed droop
control, which can work incorrectly, if the converters are not equally loaded, because of
some unusual environment.
It is extensively explained in literature [21].

52

References
[1]
EREC. European Renewable Energy Council, Wind Energy. Available online at:
http://www.erec.org/renewable-energy.html
[2]
GWEC. Global Wind Energy Council, Global Wind Report. Annual Market Update
2012. Available online at: http://www.gwec.net
[3]
EWEA. The European Wind Energy Association Report, Eastern winds. Emerging
European wind power markets in February 2013. Available online at:
http://www.ewea.org/
[4]
Meah, K.; Ula, S., "Comparative Evaluation of HVDC and HVAC Trans mission
Systems," Power Engineering Society General Meeting, 2007. IEEE , vol., no., pp.1,5, 24-28
June 2007.
[5]

ABB, HVDC transmission for lower investment cost. Available online at:

http://www.abb.com/industries/db0003db004333/678bb83d3421169dc1257481004a4284
.aspx
[6]
Temesgen Haileselassie, Kjetil Uhlen, Control and Operation of Multi-terminal VSCHVDC.
Available
online
at:
http://www.iea.lth.se/seminars/systemoperation/3_Uhlen_MTDC.pdf
[7]
ALSTOM. Dr Radnya A Mukhedkar, Introduction to HVDC. Available online at:
http://www.sarienergy.org/PageFiles/What_We_Do/activities/HVDC_Training/Presentations/Day_7/LCC_v
s_VSC_ALSTOM.pdf
[8]
Franck, C.M., "HVDC Circuit Breakers: A Review Identifying Future Research
Needs," Power Delivery, IEEE Transactions on , vol.26, no.2, pp.998,1007, April 2011
[9]
ABB. Bjrn Jacobson, ABB Power Systems, Developments in Multiterminal HVDC
in October 2011.
[10] Jiebei Zhu; Booth, C., "Future multi-terminal HVDC transmission systems using
Voltage source converters," Universities Power Engineering Conference (UPEC), 2010 45th
International , vol., no., pp.1,6, Aug. 31 2010-Sept. 3 2010.
[11] Energinet,
Kriegers
Flak
project.
http://energinet.dk/Flash/Kriegers-Flak/EN/index.html

Available

online

at:

[12] Fairley, P., "Germany jump-starts the supergrid," Spectrum, IEEE , vol.50, no.5, pp.,,
May 2013.
[13]

Airtricity, European Offshore Supergrid Proposal. Vision and Executive Summary.

[14] Michael P. Bahrman and Brian K. Johnson, The ABCs of HVDC Transmission
Technologies.
[15]

ABB, HVDC Light. Its time to connect.

53

[16] E-Cigre. International Council on large Electric Systems, Components Testing of VSC
System for HVDC Applications. Available online at: http://www.e-cigre.org/
[17] Amirnaser Yazdani, Reza Iravani, Voltage-Sourced Converters in Power Systems.
Modeling Control and Applications.
[18] Pinto, R.T.; Bauer, P.; Rodrigues, S.F.; Wiggelinkhuizen, E.J.; Pierik, J.;
Ferreira, B., "A Novel Distributed Direct-Voltage Control Strategy for Grid
Integration of Offshore Wind Energy Systems Through MTDC Network," IEEE Trans.
Ind. Electron., vol. 60, no.6, pp.2429,2441, June 2013.
[19] Haileselassie, T.M.; Uhlen, K., "Precise control of power flow in multiterminal VSC HVDCs using DC voltage droop control," Power and Energy Society General Meeting, 2012
IEEE , vol., no., pp.1,9, 22-26 July 2012.
[20] Haileselassie, T.M.; Uhlen, K., "Impact of DC Line Voltage Drops on Power
Flow of MTDC Using Droop Control," Power Systems, IEEE Transactions on ,
vol.27, no.3, pp.1441,1449, Aug. 2012.
[21] Chaudhuri, N.R.; Chaudhuri, B., "Adaptive Droop Control for Effective Power
Sharing in Multi-Terminal DC (MTDC) Grids," Power Systems, IEEE Transactions
on , vol.28, no.1, pp.21,29, Feb. 2013.

54