PRINTERS INSTRUCTIONS:

INSTR,INSTL,2GIG-CP2-345E,V1.9 - LINEAR P/N: 233497 X8 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND WITH 80 LB. WHITE COATED COVER - SIZE: 8.500 X 11.000 - SCALE: 1-1 - FOLDING: ALBUM FOLD - BINDING: SADDLE-STITCH - FINISH: 3-HOLE STD. DRILL

Wireless Security System

2GIG-CNTRL2
(2GIG-CP2)

Installation & Programming

Instructions

National Fire Protection Association Standard #72

Recommendations for Smoke Detectors
STANDARD FOR ALARM LOCATION
Smoke detectors used with this system should be installed in accordance
with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72 (National Fire
Protection Association, Batterymarch Park, Quincy, MA 02269) which reads as
follows:
2-1.1.1 Smoke alarms shall be installed outside of each separate sleeping area
in the immediate vicinity of the bedrooms and on each additional story of the
family living unit including basements and excluding crawl spaces and unfinished
attics. In new construction, a smoke alarm shall be installed in each sleeping
room.
2-1.1.2 For family living units with one or more split levels (i.e., adjacent levels
with less than one full story separation between levels), a smoke alarm required by
2-1.1.1 shall suffice for an adjacent lower level, including basements. (Exception:
Where there is an intervening door between one level and the adjacent lower
level, a smoke alarm shall be installed on the lower level.)
Ceiling mounted smoke alarms should be located in the center of the room
or hall, or not less than 4 inches from any wall. When the alarm is mounted
on a wall, the top of the alarm should be 4 to 12 inches from the ceiling.
Do not install smoke alarms where normal ambient temperatures are above
100F (37.8C), or below 40F (4C). Also, do not locate alarm in front
of air conditioners, heating registers, or other locations where normal air
circulation will keep smoke from entering the detector.

THIS SECURITY SYSTEM COMPLIES WITH

NFPA REQUIREMENTS FOR TEMPORAL
PULSE SOUNDING OF FIRE NOTIFICATION
APPLIANCES.

A-2.5.2.1 Smoke Detection - Are More Smoke Alarms Desirable? The required
number of smoke alarms might not provide reliable early warning protection for
those areas separated by a door from the areas protected by the required smoke
alarms. For this reason, it is recommended that the householder consider the use
of additional smoke alarms for those areas for increased protection. The additional
areas include the basement, bedrooms, dining room, furnace room, utility room,
and hallways not protected by the required smoke alarms. The installation of
smoke alarms in kitchens, attics (finished or unfinished), or garages is not
normally recommended, as these locations occasionally experience conditions
that can result in improper operation.
Smoke alarms are not to be used with detector guards unless the combination
has been evaluated and found suitable for the purpose.

Figure 1. Smoke Alarm Locations

Table of Contents
Introduction................................................................................ 2
System Overview ....................................................................... 3
Control Panel Features ............................................................. 4
Installation Outline .................................................................... 5
Wireless Installation Tips .......................................................... 5
Wireless System Sensors ......................................................... 6
2GIG-DW10 Thin Door/Window Contact ............................... 6
2GIG-DW20R Recessed Door Contact ................................. 6
2GIG-PIR1 Passive Infrared Motion Detector ........................ 6
2GIG-KEY2 4-Button Key Ring Remote ................................ 6
2GIG-PANIC1 Panic Button Remote...................................... 6
2GIG-GB1 Glass Break Detector........................................... 6
2GIG-SMKT2 Smoke and Heat Detector ............................... 6
2GIG-TS1 Wireless Touch Screen Keypad ............................ 6
2GIG-PAD1 Wireless Keypad ................................................ 6
2GIG-TAKE-345 Super Switch Wireless Takeover Module .... 6
System Accessories.................................................................. 7
2GIG-GSMx GSM Module ..................................................... 7
2GIG-ANT1 Internal GSM Antenna ....................................... 7
2GIG-ANT1X External In-wall GSM Antenna ........................ 7
2GIG-ANT2X External Attic Mount GSM Antenna................. 7
2GIG-ANT4X External In-wall GSM Antenna ........................ 7
2GIG-BATT1 Standard Battery Pack ..................................... 7
2GIG-BATT1X Extended Battery Pack .................................. 7
2GIG-AC1 Replacement Power Supply ................................. 7
Installation.................................................................................. 8
Control Panel Mounting Plate ................................................ 8
Wireless Sensors ................................................................... 8
Hardwired Loops.................................................................... 8
Remote Alarm Sounder ......................................................... 9
Solid State Output.................................................................. 9
Communicator Telephone Line .............................................. 9
Optional GSM Module Installation ....................................... 10
Control Panel Wiring ............................................................ 11
Backup Battery Connection and Power Supply Wiring ........ 11
Control Panel and Power Supply Mounting ......................... 11
Main Display Screens.............................................................. 12
Home Screen ....................................................................... 12
Security Screen ................................................................... 12
Arming Screen ..................................................................... 12
Menu Screen ....................................................................... 12
Status Screen ...................................................................... 12
Toolbox Screens ...................................................................... 13
Toolbox Screens .................................................................. 13
Installer Code Entry Screen ................................................. 13
Installer Toolbox Screen ....................................................... 13
System Configuration Screen .............................................. 13
System Status Icons ............................................................... 14
AC Power Icon ..................................................................... 14
Phone Line Failure Icon ....................................................... 14
Sounder Disable Icon .......................................................... 14
Backup Battery Status Icon ................................................. 14
Test Mode Icon .................................................................... 14
Touch Screen Keypad Traffic Icon ........................................ 14
GSM Radio Icon .................................................................. 14
Interior Sensor Open Icon.................................................... 14

Programming Navigation ........................................................ 15

Navigation Arrows & Go To Button....................................... 15
Questions without Sub-options ............................................ 15
Questions with Sub-options ................................................. 15
Questions with Data to Enter ............................................... 15
Other Buttons Displayed ...................................................... 15
Programming Outline .............................................................. 16
SIA CP-01 Defaults .............................................................. 16
Programming Question Table ................................................. 17
System Sensor Types .............................................................. 18
Sensor Types (Zones) .......................................................... 18
System Vocabulary Table ........................................................ 19
Installer Programming ............................................................ 20
RF Sensor Programming ..................................................... 20
RF Sensor Programming Outline ................................... 20
RF Sensor Summary Screen ......................................... 21
RF Sensor Programming Steps ..................................... 22
Wired Sensor Programming ................................................ 24
Wired Sensor Programming Outline .............................. 24
Wired Sensor Summary Screen .................................... 24
Wired Sensor Programming Steps................................. 25
RF Key Fob Programming ................................................... 26
RF Key Fob Programming Outline ................................. 26
RF Key Fob Summary Screen ....................................... 26
RF Key Fob Programming Steps ................................... 27
RF Keypad Programming .................................................... 28
RF Keypad Programming Outline .................................. 28
RF Keypad Summary Screen ........................................ 28
RF Keypad Programming Steps..................................... 29
Control Panel Programming Questions ............................... 30
Final Installation Setup ........................................................... 39
Exiting Programming ........................................................... 39
Customizing the Installation ................................................. 39
Installer Testing........................................................................ 40
Testing the System .............................................................. 40
Sounder Disable/Enable ...................................................... 40
Zone Reporting Test ............................................................ 40
Walk Test Mode.................................................................... 41
Signal Strength Indicators .............................................. 41
Radio Status Mode .............................................................. 42
GSM Radio Test ............................................................. 42
Telephone Test ..................................................................... 42
Restoring Programming Defaults ......................................... 42
Restore Defaults .................................................................. 42
Regulatory Information & Limited Warranty ......................... 43
Wireless Product Notice ...................................................... 43
FCC Notice .......................................................................... 43
FCC Telephone Rules and Regulations ............................... 43
Industry Canada Notices ..................................................... 43
Limited Warranty .................................................................. 43
Reference Programming Question Table............................... 44
Reference System Vocabulary Table ...................................... 45
Notes......................................................................................... 46
Index ......................................................................................... 48

Introduction
The Go!Control Security System represents a significant
advancement in fully supervised wireless security systems. The
security system Control Panel incorporates many advanced
and sophisticated features. The system can be expanded and
customized to fit the installations specific needs.
Designed to meet or exceed the requirements for ETL Listed
residential security installations, the system also conforms to the
Security Industry Associations Control Panel Standard ANSI/SIA
CP-01-2010.
NOTE: Failure to install the Control Panel and accessories in
accordance with ETL requirements listed in this manual voids
the ETL listing mark assigned by Intertek.
Many insurance companies offer discounts on homeowners and
renters policies when a security system is installed. Discount
credits vary with different companies and generally increase in
savings with an increase in the level of protection. Inform the user
to ask their insurance agent about savings available.
This security system is ETL Listed. For an ETL smoke alarm
system, there must be at least one smoke detector programmed
into the Control Panel to meet National Fire Protection Association
(NFPA) Rule 72-Chapter 2, and UL 217 requirements. Many
insurance companies require meeting these requirements to
qualify for a discount. For an ETL smoke alarm system, use only
approved model smoke detectors with this Control Panel.

2GIG-CNTRL2
(2GIG-CP2)

NOTE: Some cities and municipalities may require an alarm

system permit. Check with the local authorities before installing
this system.

REFERENCE ONLY - REFER TO ADDENDUM 230373 FOR PROPER

INSTALLATION AND WIRING DIAGRAM
UL NOTE: WIRING FOR ALL WIRED SENSORS AND ANNUNCIATORS MUST USE
UL LISTED LOW VOLTAGE CL2X OR BETTER GRADE WIRE. SENSOR AND DISPLAY
VOLTAGES MUST COMPLY WITH CLASS 2 LOW VOLTAGE REQUIREMENTS.

TELEPHONE LINE
FROM RJ31X
TELEPHONE JACK

CONTROL PANEL

TELEPHONE
JACK

HARDWIRE LOOPS
CAN BE PROGRAMMED
AS NORMALLY OPEN OR CLOSED

NORMALLY
OPEN
CONTACT
2.2 K

NORMALLY CLOSED
CONTACT
2.2 K

PIEZO
SIREN

SUPERVISED BELL OUTPUT

6-12 VDC @ 120 mA MAXIMUM

END-OF-LINE RESISTORS ARE

OPTIONAL ON HARDWIRE LOOPS

8 - HARDWIRE LOOP 2
7 - HARDWIRE LOOP 1 ALL OUTPUT
VOLTAGES
6 - BELL (-)
ARE CLASS 2
5 - BELL (+)
4 - OPEN COLLECTOR OUTPUT
3 - GROUND
2 - 14 VDC POWER INPUT (-)
1 - 14 VDC POWER INPUT (+)

OPEN COLLECTOR OUTPUT

250 mA @ 16 VDC MAXIMUM

1K

LED

EXAMPLE HOOKUP SHOWING AN ARMED LED,

THE OPEN COLLECTOR OUTPUT CAN BE PROGRAMMED
TO ACTIVATE DURING VARIOUS CONDITIONS

120 VAC 60 HZ
PLUG-IN 14 VDC
1.7 AMP SWITCHING
POWER SUPPLY
OBSERVE
POLARITY WHEN
CONNECTING THE
POWER SUPPLY !!!

Figure 2. Control Panel Wiring Diagram

NOTE: TERMINAL 1 WILL ONLY

PROVIDE DC POWER WHEN
THE CONTROL PANEL'S
POWER SUPPLY IS CONNECTED
TO AN AC POWER SOURCE

System Overview
The systems Control Panel features a color touch screen display that
allows control of all system functions and programming. The display
clearly shows the installer and subscriber system and installation
status. The helpful scrolling text, along with the voice prompts
that the Control Panel sounds, make installation, programming,
and operation very easy compared to keypad-programmed and
operated security systems of the past.

The optional GSM radio modem also allows 2-way communications

with the Alarm.com server. Through this server, subscribers can
query and control their system using a computer browser from
anywhere in the world. The Alarm.com server can also send
messages, time corrections, and software updates to the Control
Panel. Special messages from the server are displayed to the
subscriber on the Control Panels color touch screen.

The system supports 48 wireless sensors of various types, two

hardwire loops, 15 sensor response types, a supervised bell output,
and a programmable solid-state control output. An on-board digital
communicator reports alarms and trouble to a central monitoring
station receiver via the standard telephone network. The Control
Panel also supports 2-way voice communications with the Central
Station.

For home control, the Control Panels built-in Z-Wave radio module
allows controlling and monitoring various home automation devices
such as lighting, locks, heating, and air conditioning. The Z-Wave
radio module can also activate Z-Wave remote alarm sirens.

An internal 345 MHz narrow-band radio receiver detects signals

from wireless system sensors. The high-gain receiver allows for
easy placement of the wireless sensors so signals can be received
in even the toughest of installation environments.
When the optional Model 2GIG-XCVR2 900 MHz transceiver is
installed, it sends and receives signals with accessory wireless
touch screen keypads. Touch screen keypads allow remote control
of the system through the same graphic interface design as the
Control Panel.

32 User Codes including a Duress Code are supported. User one

is the Master User Code that can add or delete the other 31 User
Codes. The Installer Code must be unique from any other User
Code and is the only code that has access to system programming.
The front panel
and
buttons serve as controls as well as
indicators. Pressing the
button displays emergency icons on the
display for Panic, Fire, and Emergency alarm activation (each has
programmable options and can be enabled or disabled). Pressing
the
button changes the system display to the Home Screen.

For enhanced operation, an optional Model 2GIG-GSMx global

system for mobile communications module (GSM radio modem)
can be installed in the field. With the optional GSM radio modem
installed, the system will have wireless Central Station reporting
capability. 2-way voice communication with the Central Station can
also go over-the-air through the GSM radio modem.

Door /
Window
Sensors

Color Display
Home &
Emergency
Buttons

Speaker
&
Microphone

PIR
Motion
Sensors

Subscribers
PDA

Subscribers
Computer

Color LCD
Display with
Touch Screen

Digital
Communicator

Siren

Subscriber

Hardwire Inputs

Existing
Sensor
Installation

Cell
Site

Touch Screen

Hardwire
Loop
#2

Voice

Hardwire
Loop
#1

Public
Switched
Telephone
Network

Central Station
Receiver

Optional
GSM
Module
Alarm.com
Web site

GSM
Telephone
Network

CONTROL PANEL

CPU
Alarm.com
Server

Glass
Break
Sensors

Standard 345 MHz Receiver

or Optional
345 MHz / 900 MHz Transceiver

Bell
Output

System
Power

Z-Wave
Radio

Alarm.com
Infrastructure

CO
Sensors

Database

Thermostat

Power
Supply

Smoke
Sensors
Panic
Buttons

Key
Fobs

Wireless
Keypads

Up to 48 Wireless Sensors per System

Wireless
Touch
Screens

Lighting
Control
Piezo
Siren
120 VAC
Input
Power

Remote
Sirens

Door
Locks

Figure 3. System Block Diagram

Control Panel Features

ALARM SOUNDER
AND SPEAKER

COLOR DISPLAY
WITH TOUCH SCREEN

Sounds all system local alarms,

voice prompts, system sounds, and
audio for 2-way voice communications
with the Central Station

Shows all system information, status,

programming, and functions as the
keypad
The display also cycles between
clock/calendar and weather
(press to manually change)

EMERGENCY
BUTTON / INDICATOR
Lights WHITE when enabled for
emergency alarm
Flashes WHITE during
emergency alarm

MICROPHONE
For voice communication
with the Central Station

HOME
BUTTON / INDICATOR
Sensor Status

Lights GREEN when ALL sensors are closed (ready to arm)

Not lit when ANY sensor is open (not ready to arm)

Arming Status

Lights RED while system is armed

Blinks RED during the Entry Delay

Alarm Memory

Blinks RED during an alarm

Blinks RED after an alarm while system is still armed

HOME
BUTTON / INDICATOR
Power Outage

Indicator flashes during power outages (system on battery backup)

Flashes GREEN when ALL sensors are closed (ready to arm)
Flashes ORANGE when ANY sensor is open (not ready to arm)
Flashes RED while system is armed

Figure 4. Control Panel External Features

"THIRD HAND"
HANGER STRAP
Hooks onto mounting plate during installation
to hold the Control Panel while wiring

BACKUP BATTERY PACK

7.2 Volt Ni-mh battery pack is included
with the Control Panel, replacement
part number 2GIG-BATT1
For UL985 installations, use the
Model 2GIG-BATT1X battery pack

TELEPHONE LINE
MONITOR TERMINALS
Terminals for connecting lineman's
"buttset" for monitoring the telephone line

TELEPHONE JACK
For RJ45 connection to installation's
RJ31X telephone jack, incoming and
outgoing lines for full line seizure

MAIN RECEIVER MODULE

345 MHz receiver for wireless sensors
Optional Model XCVR2 345 / 900 MHz
transceiver for touch screen keypads
(XCVR2 is not for UL985 installations)

GSM ANTENNA (HIDDEN)

Internal Model 2GIG-ANT1 GSM antenna
mounts in the side of the Control Panel case

TERMINAL BLOCK
Connections for power, solid state output
bell, and hardwire loops

Figure 5. Control Panel Internal Features

OPTIONAL GSM RECEIVER MODULE

Model 2GIG-GSMx GSM Module for over-the-air
communication with the Alarm.com
Central Station

Installation Outline

Wireless Installation Tips

The following outline is intended to guide the installing alarm

dealer through the complete installation of a Go!Control system.

When installing any wireless system, certain limitations must

be considered. Low power wireless transmitter signals will not
broadcast equally through all types of construction materials. The
Control Panel contains a very sensitive receiver that should allow
placement of transmitters in almost all locations.

Use the following outline in conjunction with this copy of the

Installation Instructions to guide you through the installation.
1. Unpack the system. Identify the system components.
2. Plan the installation by creating an installation floor plan.
Determine the best centralized location for the Control Panel.
Decide on where the wireless sensors will be installed.

Here are some general wireless guidelines that should be reviewed

before beginning the installation. Follow these tips to create the
best possible functioning wireless installation.

3. Identify an un-switched 120 VAC power source for plugging

in the Control Panels power supply.
4. Identify or install a U.S.O.C. RJ31X telephone jack for
connection of the Control Panels communicator.

CONTROL PANEL LOCATION RELATIVE TO SENSORS

5. Use the Control Panels mounting plate as a template to mark

the mounting location for the Control Panel. Mark any drywall
cutouts behind the mounting plate required for the installation
and make the cutouts.
6. Attach the mounting plate to the wall using three screws.
7. Install each of the systems wireless sensors. If either of the
two hardwire loops are going to be used, install the contacts
and route the loop wire to the Control Panels wall cutout. Use
the log in the quick programming guide to document each
sensors ID number and location.

RIGHT

WRONG!

CENTRALLY LOCATE
CONTROL PANEL

SENSORS AT THE OTHER END OF

HOUSE MIGHT BE TOO FAR AWAY

CONTROL PANEL LOCATION HEIGHT

8. Install the optional remote sounder, and route the connection

wire to the Control Panels wall cutout.
9. Route the telephone line from the RJ31X jack to the Control
Panels wall cutout.

BASEMENT

BASEMENT

11. Connect all wiring to the Control Panels terminal block.

12. Plug the telephone line into the Control Panels telephone
jack.

CONTROL
PANEL

CONTROL
PANEL

10. Using the third hand strap, hang the Control Panel on the
mounting plate in preparation for wiring.

RIGHT

WRONG!

MOUNT CONTROL PANEL AS HIGH ABOVE

EARTH LEVEL AS PRACTICAL

LOCATING CONTROL PANEL BELOW

EARTH LEVEL WILL IMPAIR RANGE

13. Plug the backup battery connector into the connector on the
Control Panels circuit board.
14. Swing the Control Panel up, placing the bottom over the lip of
the mounting bracket. Push the top of the Control Panel into
the mounting bracket until it snaps into place, then secure it
with the retaining screw.

SENSOR SIGNAL LOSS THROUGH MATERIALS

65% - 95%
OF FULL POWER

90% - 100%
OF FULL POWER

15. Plug the power supply into the un-switched 120 VAC wall
outlet.

10% - 70%
OF FULL POWER

16. Program the system as described in this manual and mark

the check boxes in the Operation and Users Guide to indicate
any custom setup to the subscriber.
17. Test the system as described in this manual.
WALLBOARD AND
WOOD STUDS

18. Instruct the subscriber on the system operation and provide

the Operation and Users Guide to the subscriber.

LIGHT CONCRETE
OR BRICK

CONCRETE WITH STEEL

REINFORCEMENT OR
METAL LATH AND PLASTER

LOCATION OF SENSORS

SENSOR
Less
than
3 ft.
above
slab

DOOR
Min.
3 ft.

DOOR

Wall

Concrete
slab
floor

Concrete
slab
floor
SENSOR

SENSOR

RIGHT

Large
metal
appliance
(refrig.)

WRONG!

WRONG!

Figure 6. Wireless Installation Tips

Wireless System Sensors

2GIG-DW10
Thin Door/Window Contact
For narrow applications,
sensor is only 3/4 wide
Fully supervised
Rare earth magnet
Lithium battery
Supports internal and external contacts
Can be used for two
zones of protection
345 MHz
ETL Listed

2GIG-DW20R
Recessed Door Contact

Compact size, only 2-1/2 long

Fully supervised
Rare earth magnet
Lithium battery
345 MHz
ETL Listed

2GIG-PIR1
Passive Infrared Motion Detector
Dual element sensor with
50 by 50 range
45 lb. pet immune
90 degree look down
Lithium battery
345 MHz
ETL Listed

2GIG-GB1
Glass Break Detector
Monitors for the sound
of breaking glass
Two test LEDs
Dual shatter recognition
technology (thud then crash)
Lithium battery
345 MHz
ETL Listed

2GIG-SMKT2
Smoke and Heat Detector
Photoelectric-type detector
with rate-of-rise and fixed
135 heat sensors
Status indicator
Built-in 85 dBA sounder
Lithium battery
345 MHz
ETL Listed

2GIG-TS1
Wireless Touch Screen Keypad
Wireless communication
with Control Panel
Same graphic interface
as Control Panel
Supports all user functions
of the Control Panel
900 MHz
NOTE: Not for UL985
installations.

2GIG-PAD1
Wireless Keypad
2GIG-KEY2
4-Button Key Ring Remote
Arms system in Stay or Away Mode
Disarms system
Auxiliary output and
emergency functions
Lithium battery
345 MHz
ETL Listed

Arms system in Stay

or Away Mode
Disarms system
Fire and Panic
emergency functions
Lithium batteries
345 MHz
ETL Listed

2GIG-TAKE-345
Super Switch Wireless
Takeover Module
2GIG-PANIC1
Panic Button Remote

For triggering emergency alarm

Small and lightweight
5-second button lockout
Lithium battery
345 MHz
ETL Listed

Eight-channel transmitter
Converts up to eight
hardwired loops into eight
wireless sensor zones
9-16 VDC, 50 mA
Can be powered from
existing Control Panel
345 MHz
ETL Listed

System Accessories
2GIG-GSMx
GSM Module
Cellular telephone module
Plugs into Control Panel
Provides 2-way GSM
radio communication
Enrolls with cellular service provider

2GIG-ANT1
Internal GSM Antenna
Antenna installs inside
Control Panel
Plugs into GSM module
Small size
Locking connector

2GIG-ANT1X
External In-wall GSM Antenna
Antenna installs in the wall
behind Control Panel
2-foot cable
Plugs into GSM module
Locking connector

2GIG-BATT1
Standard Battery Pack
Standard battery supplied
with Control Panel
Also available as a replacement
item
Nickel metal hydride (NiMH) battery

2GIG-BATT1X
Extended Battery Pack
Optional extra capacity battery
Replaces standard internal
Control Panel battery
Required for UL985 fire
warning system listing
Nickel metal hydride (NiMH) battery

2GIG-AC1
Replacement Power Supply
High efficiency switching
power supply
120 VAC @ 60 Hz input
14 VDC @ 1700 mA output
Screw terminals for wiring
connecting to the Control Panel
Includes retaining bracket
for standard and Decora style outlets.

2GIG-ANT2X
External Attic Mount GSM
Antenna
Antenna installs in attic
above Control Panel
10-foot cable
Plugs into GSM module
Locking connector

2GIG-ANT4X
External In-wall GSM
Antenna
Antenna installs in the wall
behind Control Panel
2-foot cable
Plugs into GSM module
Locking connector

Installation
Control Panel Mounting Plate
The Control Panel should be mounted on the wall in an easy
location for the subscriber to operate the system.

IF USING EXTERNAL
GSM ANTENNA, REMOVE
KNOCKOUT

MOUNTING
PLATE

1. Remove the locking screw from the top of the Control Panel case and
remove the mounting plate.

MOUNT
PLATE
WITH 3
SCREWS

2. Use the mounting plate as a template to mark the wall for the wiring
cutout slot. Use a drywall saw to cut the slot. If using the optional
Model 2GIG-GSMx GSM module with the external Model 2GIG-ANT1X
or Model 2GIG-ANT2X antenna, remove the plastic knockout labeled
EXTERNAL ANTENNA on the mounting plate. Mark and cut a slot in the
drywall for the external antenna.

REMOVE CASE SCREW

AND MOUNTING PLATE

3. Attach the mounting plate to the wall using three screws.

Wireless Sensors

USE MOUNTING PLATE

AS A TEMPLATE TO
MARK WIRE CUTOUT
HOLE IN DRYWALL

Figure 7. Wall Mounting Template

Each wireless sensor needs to be installed at its desired location.

1. Following the instructions included with each wireless sensor, install each
sensor at its desired location.
2. Use the Installation Log to document each sensors ID number and
location.

Hardwired Loops
Hardwired loops can be programmed either normally open (N/O)
or normally closed (N/C). End-of-line resistors (EOLR) can also be
used to supervise the loops.
Only contacts should be used with the hardwired loops. The Control
Panel does not support powering external devices (PIRs, etc.).
NOTE: HARDWIRED LOOPS CANNOT BE USED FOR A CO
OR FIRE SENSOR LOOP.
1. If either of the two hardwired loops are going to be used, install the contacts
and route the loop wire to the Control Panels wall cutout.
2. If end-of-line supervision is required for the loop, install a 2.2K ohm resistor
(not supplied) as shown in the loop illustration.

Figure 8. Typical Door Sensor Installation

N.C.

N.C.

GROUND

HARDWIRE
LOOP 1 OR 2

GROUND

HARDWIRE
LOOP 1 OR 2

GROUND

HARDWIRE
LOOP 1 OR 2

GROUND

HARDWIRE
LOOP 1 OR 2

GROUND

HARDWIRE
LOOP 1 OR 2

HARDWIRE LOOP WIRING EXAMPLES

N.C.

N.O.

N.C.
LOOP

N.O.
LOOP
HARDWIRE LOOPS NEED TO BE
PROGRAMMED FOR CONTACT TYPE

2.2K EOLR
N.C.
EOL LOOP

Figure 9. Hardwired Loop Wiring

N.O.

N.O.

2.2K EOLR
N.O.
EOL LOOP

2.2K EOLR
MIXED
EOL LOOP

Installation
Remote Alarm Sounder
The Control Panel provides two terminals for an optional connection
to a remote electronic alarm sounder (see Figure 10).

THE BELL OUTPUT CAN BE PROGRAMMED

FOR SUPERVISION TO DETECT IF THE
WIRE TO THE BELL IS CUT

The bell terminals can be supervised. If siren supervision is

enabled (Q-21), and the wire between the Control Panel and
sounder is cut, the Control Panel will indicate a trouble alert for
siren supervision and report bell trouble to the Central Station.

820

WARNING: Do not connect an electromechanical bell to these

terminals. Damage to the output will occur.

PIEZO
SIREN

8 - HARDWIRE LOOP 2
7 - HARDWIRE LOOP 1
6 - BELL (-)
5 - BELL (+)
4 - OPEN COLLECTOR OUTPUT
3 - GROUND
2 - 14 VDC POWER INPUT (-)

SUPERVISED BELL OUTPUT

6-12 VDC @ 120 mA MAXIMUM

FOR VERY LOW CURRENT SOUNDERS,

INSTALL AN 820 RESISTOR IN PARALLEL
WITH THE SOUNDER

1. Install the remote sounder in a secure location where it can easily be

heard.

1 - 14 VDC POWER INPUT (+)

USE SOLID STATE SOUNDERS ONLY

DO NOT CONNECT TO AN ELECTROMECHANICAL BELL !!!

2. Route wiring from the remote sounder location to the Control Panels wall
cutout.

Figure 10. Remote Sounder Wiring

NOTE: If the piezo alarm siren used for a remote sounder has
an extremely low current draw and/or the sounder produces
hum or noise, install an 820 resistor in parallel with the
sounder (see Figure 10).

Solid State Output

The Control Panel provides one solid state output that can be
programmed to activate during various conditions. The output can
switch up to 250 Ma @ 16 VDC to ground. Refer to Figure 11 for
examples of devices wired to the output.

OPEN COLLECTOR OUTPUT

250 mA @ 16 VDC MAXIMUM
OUTPUT SWITCHES TO
GROUND WHEN ACTIVATED

This output will only function while the Control Panel is

receiving power from the wall power supply.

8 - HARDWIRE LOOP 2
7 - HARDWIRE LOOP 1
6 - BELL (-)
5 - BELL (+)
4 - OPEN COLLECTOR OUTPUT
3 - GROUND
2 - 14 VDC POWER INPUT (-)

NOTE: FOR ETL LISTING,

AN EXTERNAL DC BACKUP
POWER SUPPLY IS REQUIRED
FOR A LOAD CONNECTED
TO TERMINAL 4

1. Install the device to be controlled by the solid state output.

2. Route wiring from the device location to the Control Panels wall cutout.
WARNING: Do not connect an electromechanical bell to these
terminals. Damage to the output will occur.

Communicator Telephone Line

1 - 14 VDC POWER INPUT (+)

1K

LED
NOTE: TERMINAL 1 WILL ONLY
PROVIDE DC POWER WHEN
THE CONTROL PANEL'S
POWER SUPPLY IS CONNECTED
TO AN AC POWER SOURCE

EXAMPLE HOOKUP SHOWING AN ARMED LED,

THE OPEN COLLECTOR OUTPUT CAN BE PROGRAMMED
TO ACTIVATE DURING VARIOUS CONDITIONS

Both an incoming telephone line and an outgoing telephone line

will be connected to the Control Panel. When the communicator
activates, all local telephones will be disconnected to prevent
an off-hook telephone on the premises from blocking the
communicators call. See Figure 12 for RJ31X jack wiring details.

Figure 11. Solid State Output Wiring

1. Run a 4-conductor telephone cable from the telephone company

demarcation box to the Control Panel mounting plate.
2. At the demarcation box, disconnect the house telephones that are
wired to the box output. DO NOT DISTURB THE TELCO INPUT
DROP SIDE OF THE BOX OR ANY EARTH GROUNDS.

RED (RING IN)

GREEN (TIP IN)

INCOMING TELEPHONE LINE

FROM DEMARCATION BOX
IMPORTANT !
FOR PROPER LINE SEIZURE, ALL HOUSE
TELEPHONE CONNECTIONS MUST PASS
THROUGH THE RJ31X JACK

RJ31X
TELEPHONE
JACK

3. At the demarcation box, connect the RED cable wire to the

box RING, and the GREEN cable wire to the box TIP.

BLACK (RING OUT)

YELLOW (TIP OUT)

OUTGOING TELEPHONE LINE

TO HOUSE TELEPHONES

4. At the demarcation box, connect the BLACK cable wire

to the house telephone RING wire(s), and the YELLOW
cable wire to the house telephone TIP wire(s).
5. At the Control Panel, connect the cables RED wire to
the RJ31X jacks RING IN terminal, and the GREEN
wire to the RJ31X jacks TIP IN terminal.
6. At the Control Panel, connect the cables BLACK wire to
the RJ31X jacks RING OUT terminal, and the YELLOW
wire to the RJ31X jacks TIP OUT terminal.

CONTROL PANEL
TELEPHONE
JACK
PLUG CABLE
FROM CONTROL
PANEL INTO JACK

PLUG CABLE
FROM JACK
INTO CONTROL
PANEL

Figure 12. Telephone Jack Wiring

7. Snap the cover on the jack. Plug one end of the modular cable into the
jack and slide it through the hole in the mounting plate into the wall.

Installation
Optional GSM Module Installation
1

If using the optional GSM module and one of the GSM antennas.
Refer to the following steps:
1. Plug the GSM module into the connector on the Control Panels circuit
board. Secure it with the two screws.
2A. If using the Model 2GIG-ANT1 internal antenna, remove the antenna
access cover. Route the antenna lead through the opening in the case and
place the flat antenna into the slot. Route the antenna wire under the clip
behind the speaker and plug the antenna connector into the GSM module.
Replace the antenna access cover. See Figure 13.
NOTE: The routing of the GSM antenna wire is very critical.
Route the wire as directed or GSM radio interference will occur
inside the Control Panel.
2B. If using one of the external antennas, simply plug the antenna connector
into the GSM module. The antenna will drop into the wall or mount in
the attic with the cable passing through the slot in the Control Panels
mounting plate. See Figures 14 & 15.
NOTE: The GSM SIM card should have been pre-activated by
the factory; if not, contact your service provider. For the GSM
module to function with the system, it will have to be activated
before it can be enrolled by creating an account with the
service provider.

PLUG GSM
MODULE INTO
CONTROL
PANEL

2
PRY OPEN
ANTENNA ACCESS
COVER

3
PLACE
ANTENNA
INTO SLOT
AS SHOWN

ROUTE GSM ANTENNA CABLE

EXACTLY AS SHOWN !!!

4
SECURE GSM
MODULE WITH
TWO SCREWS

ROUTE GSM ANTENNA CABLE

EXACTLY AS SHOWN !!!

Figure 13. Optional GSM Module Installation

2GIG-ANT2X
GSM ANTENNA
MOUNTED AS HIGH
AS POSSIBLE

GSM CONNECTOR

ANTENNA HANGS
DOWN INSIDE WALL
2GIG-ANT1X
ANTENNA
COAX TO
CONTROL
PANEL

Figure 14. ANT1X In-wall GSM Antenna Installation

10

Figure 15. ANT2X Attic GSM Antenna Installation

Installation
Control Panel Wiring
The Control Panel includes a third hand plastic strap that allows
the unit to hang on the mounting plate during installation.
1. Hang the Control Panel on the mounting plate using
the third hand strap (see Figure 16).
2. Connect the hardwire loop, external sounder, and open collector
output wiring (if used ) to the Control Panels terminal block.

1
HANG CONSOLE
ON STRAP

3
PLUG TELEPHONE LINE
INTO TELEPHONE JACK

2
CONNECT HARDWIRE LOOPS,
EXTERNAL SOUNDER, AND
OPEN COLLECTOR OUTPUT
TO TERMINALS

3. Plug the telephone line (if used ) into the connector

on the Control Panels circuit board.

Backup Battery Connection and Power Supply Wiring

The backup battery connects to the Control Panels circuit board
with a two-pin header assembly.
Figure 16. Control Panel Mounting

The power supply features a two-position terminal block for

connecting the power supply to the Control Panel power terminals
(connection wire not included).
1. Determine a good location where theres a 120 VAC outlet for the
plug-in power supply. The 120 VAC outlet must be un-switched (an outlet
not controlled by a wall switch). DO NOT CONNECT THE POWER
SUPPLY TO A RECEPTACLE CONTROLLED BY A SWITCH.

TERMINAL #2
- 14 VDC

POWER
SUPPLY

2. Route 2-conductor 18 AWG wire from the power supply

location to the Control Panel mounting plate.
3. BEING CAREFUL TO OBSERVE POLARITY, connect the
power supplys DC + and DC - terminals to the 18 AWG
wire. DO NOT PLUG IN THE POWER SUPPLY YET.
4. BEING CAREFUL TO OBSERVE POLARITY, connect the
18 AWG wire to the Control Panel +14 VDC Terminal #1 (+)
and -14 VDC Terminal #2 (-) power input terminals.

RIGHT
TERMINAL
- 14 VDC
LEFT
TERMINAL
+ 14 VDC

NOTE: Grounding of the Control Panel is NOT required for

proper operation.
5. Plug the backup battery packs connector into the connector
on the Control Panels circuit board. (The Control Panel
will not recognize that the battery is connected until
AC power is connected to the power supply.)

CONTROL PANEL
TERMINALS

TERMINAL #1
+ 14 VDC

OBSERVE POLARITY WHEN

CONNECTING THE POWER SUPPLY!!!

Figure 17. Power Supply Wiring

3 SWING CONSOLE UP
AND SNAP ONTO THE
MOUNTING PLATE

IMPORTANT: Applicable regulatory agencies require

installation of the extended life backup battery (P/N
2GIG-BATT1X) inside the Control Panel for UL985 Household
Fire applications.

1
CONNECT
BATTERY

Control Panel and Power Supply Mounting

With all the wiring complete, the Control Panel is ready to power up.
1. Swing the Control Panel up, placing the bottom over the lip of the
mounting bracket. Push the top of the Control Panel into the mounting
bracket until it snaps into place, then secure it with the retaining screw.
2. Peel off the adhesive backing from the power supply retaining bracket
and attach the bracket to the outlet with a wall plate screw. Note the
orientation for a standard or Decora style outlet (see Figure 19).

2
ALIGN MOUNTING
PLATE INSIDE OF
CONSOLE BOTTOM EDGE

4
AFTER INSTALLING,
SECURE CONSOLE
WITH SCREW IN
RETAINING HOLE

Figure 18. Connecting Battery and Closing Panel

3. Spread the retaining bracket ears and plug the Control Panels
power supply into the un-switched 120 VAC outlet. Slots are
provided on the bracket to secure the power supply with a zip-tie.
4. After about five seconds, the Control Panel will indicate that
power has been applied. IF THE CONTROL PANEL DOES NOT
POWER UP, CHECK THE POWER SUPPLY POLARITY!!!

POWER
SUPPLY

POWER
SUPPLY

BRACKET INSTALLED
FOR STANDARD
STYLE OUTLET

BRACKET INSTALLED
FOR DECORA
STYLE OUTLET

Figure 19. Securing the Power Supply

11

Main Display Screens

The Control Panel is programmed and operated using the color
touch-screen display. The display will show various buttons,
indicators, and text to guide the installer and user.

Home Screen
The Home Screen is the top level screen. It shows the system
status with icons to indicate system conditions. It also displays
the time and date. System information scrolls along the top of the
display. The Home Screen displays the SECURITY and SERVICES
buttons. The Silent Control and Display Off buttons are also
displayed. When the system is operating, pressing the
button
on the Control Panel will display the Home Screen.

Figure 20. The Home Screen

Security Screen
The Security Screen shows the system status and offers three
buttons for ARM, MENU, and STATUS. The Silent Control button
and the time and date are also displayed. If messages, alarm, or
trouble alerts are pending, the Security Screen will display buttons
indicating the number of pending messages or issues.

Trouble Alert

Silent Control

Alarm Memory

Arming Screen
The Arming Screen is used to arm the security portion of the
system. It displays the system status and arming buttons for STAY
and AWAY.
Option check boxes for ENTRY DELAY and SILENT EXIT are displayed.
To arm the system without an entry delay, un-check the ENTRY
DELAY check box. To arm silently without sounding the Exit Delay
beeps, check the SILENT EXIT check box. Stay Mode arming always
has a silent exit.

Message

Figure 21. The Security Screen

Menu Screen
The Menu Screen shows the system status and offers buttons for
ARM and TOOLBOX. If any of the 24-hour emergency options are
enabled, an EMERGENCY button is displayed. Two option check box
buttons for CHIME and VOICE are displayed.
Installer setup can be accessed using the TOOLBOX button.

Figure 22. The Arming Screen

The CHIME button enables/disables chimes for the entire system

(chimes can be independently enabled or disabled for each sensor
number from the Toolbox).
The VOICE button enables/disables voice announcements for
the entire system (voice announcements can be independently
enabled or disabled for each sensor number from the Toolbox).
Voice announcements always sound during alarm conditions.

Status Screen
The Status Screen lists system status and any alerts. The date and
time of alerts are listed in the displayed log.
One option button for SILENCE is displayed; it temporarily stops
the voice announcement of the system status during the status
display.

Figure 23. The Menu Screen

Figure 24. The Status Screen

12

Toolbox Screens
The Control Panel is programmed using the toolbox screens.
Users can access basic programming functions. Installers can
access basic and Installer Toolbox functions. Users and installers
must enter a valid code to access the programming functions in
the toolbox. Other functions do not require entering a code.

Toolbox Screens
From the Menu Screen, when the TOOLBOX button is pressed, the
system will ask for a User Code then display Toolbox Screen one.
The arrow button displays Toolbox Screens two and three. Each
Toolbox Screen shows option buttons that display sub-menus.

Figure 25. Toolbox Screen One

Installer Code Entry Screen

The INSTALLER TOOLBOX button goes to the main programming
area of the Control Panel and can only be accessed by the installer
while the system is disarmed by entering a correct access code.
THE INSTALLER CODE CANNOT DISARM THE SYSTEM.
The system features a special shortcut to help the installer access
the Installer Toolbox quickly. Pressing the lower right corner of
the Home Screen while the system is disarmed will immediately
display a code entry screen. When the correct Installer Code is
entered, the system will go directly to the Installer Toolbox.

Figure 26. Toolbox Screen Two

Installer Toolbox Screen

The Installer Toolbox Screen displays system setup and testing
buttons. Main programming is accessed using the SYSTEM
CONFIGURATION button. The other buttons support system tests
and resetting the Control Panel to its programming default values.

System Configuration Screen

When the SYSTEM CONFIGURATION button is pressed, the Control
Panel will display questions for each programming step. To help
the installer program the Control Panel quickly, the programming
questions are arranged so that the commonly set values appear
early in the question order.

Figure 27. Toolbox Screen Three

Figure 28. Installer Toolbox Code Entry Screen

Figure 29. Installer Toolbox Screen

Figure 30. System Configuration Question Q-1

13

System Status Icons

The top line of the Control Panels display is the status bar that
shows the current system mode, the status of the sensors, and
any current system trouble alerts. Special icons are displayed to
visually show the systems current condition.

STATUS BAR SHOWING

AC POWER IS ON

Figure 31. System Status Bar

AC Power Icon
The AC power icon indicates the Control Panels AC line power
status. The icon displays a white plug when the AC power is
present; the icon will display with a red X over the white plug
when AC power is absent.

AC POWER ON

AC POWER OFF

Figure 32. AC Power Icons

Phone Line Failure Icon

If the Control Panel detects that the telephone line is disconnected,
the phone line failure icon will be displayed.

PHONE LINE
FAILURE

Figure 33. Phone Line Failure Icon

Sounder Disable Icon

If the systems internal sounder has been lowered and external
sounder has been disabled by the installer for testing, the sounder
disable icon will be displayed. Also flashes to indicate silent arming.

SOUNDER
DISABLED

Figure 34. Sounder Disable Icon

Backup Battery Status Icon

If the Control Panels backup battery tests low, the low backup
battery icon will be displayed.

LOW BACKUP
BATTERY

Figure 35. Backup Battery Status Icon

Test Mode Icon

When the system is being tested in Walk Test Mode, the test mode
icon will be displayed on the status bar.

Touch Screen Keypad Traffic Icon

When the Control Panel is communicating to a touch screen
keypad the up arrow icon is displayed. When a touch screen
keypad communicates to the Control Panel the down arrow icon
is displayed.

SYSTEM IN
TEST MODE

Figure 36. Test Mode Icon

COMMUNICATION
IN PROCESS

Figure 37. Touch Screen Keypad Traffic Icon

GSM Radio Icon

If the systems optional GSM radio modem is installed, the GSM
radio icon will be displayed while the Control Panel is receiving
over-the-air firmware updates.

OVER-THE-AIR
UPDATE IN
PROCESS

Figure 38. GSM Radio Icon

Interior Sensor Open Icon

If an interior sensor is open (or a motion detector has just been
activated) the house icon will be displayed on the status bar. As a
warning, the icon flashes during arming.

INTERIOR
SENSOR OPEN

Figure 39. Interior Sensor Open Icon

14

Programming Navigation
When the installer is using the System Configuration menus,
the Control Panel will present each programming question
sequentially. Most programming questions have a single numeric
value response or a simple enabled/disabled selection. Some
programming questions have sub-options that can be set. These
sub-options are displayed for the question selected and can be
accessed through navigation keys on the display.

Navigation Arrows & Go To Button

The programming question screens display up, down, left, and
right navigation arrows. They are used to move through the
programming questions and sub-options.
The GO TO button is used to jump directly to a programming
question. Pressing GO TO will prompt the installer for the two-digit
question number to jump to. The GO TO button changes to CANCEL
while waiting for a question number, press CANCEL to back out.

Figure 40. Navigation Arrows & Go To Button

Questions without Sub-options

Most of the programming questions do not have sub-options. They
navigate as follows. Questions without sub-options do not
display a SKIP button.
The & arrows select the next or previous programming question.
The & arrows choose values for the question or move the cursor left
and right along the white data entry field.

Figure 41. Questions without Sub-options

Questions with Sub-options

Some of the programming questions have sub-options. They
navigate as follows. Questions with sub-options display a SKIP
button during the question.
The SKIP button advances to the next programming question/section.
The & arrows select the next or previous programming sub-question.
The & arrows choose values for the question or move the cursor left
and right along the white data entry field.

Questions with Data to Enter

Some of the programming questions require entering numeric or
alphabetic data. For devices that can be named, the Control Panel
contains a large vocabulary with words to choose from (see Pg. 19).
The INSERT button displays a word from the vocabulary. The words can
be scrolled through using the & arrows, or selected by entering their
3-digit index number.
The
(backspace) button moves the cursor to the left, deleting the one
character at a time.
The
(delete) button deletes a character to the right of the cursor, or any
characters that are highlighted.
The FWD (forward) button highlights the next word in multi-word data fields.
The BACK button highlights the previous word in multi-word data fields. The
BACK button displays the previous screen in some cases.
When the SHIFT button is displayed, pressing it will display alternate
characters on the keypad that can be used for data entry.

Figure 42. Questions with Sub-options

Figure 43. Questions with Data to Enter

Other Buttons Displayed

Depending on the programming question, other buttons may be displayed.
The ESC (escape) button serves as an undo. Pressing ESC restores the
value that was previously stored for the question or sub-question.
The SUM (summary) button displays a summary of the values stored for the
programming question and sub-options.
The END button displays a summary of the values stored for the entire
Control Panel memory.

Figure 44. Other Buttons Displayed

The LEARN button is used to set the system to receive a sensors serial
number when transmitted during programming the wireless sensors.
The PASTE button repeats the last sensor serial number entered.
The EXIT button exits programming.

15

Programming Outline
Each system installed will require programming. Most installations
being performed by the professional alarm installer for a specific
organization will have common values set in every Control Panel
reporting to the same Central Station. Other programming values,
such as the account number and sensor setup, will be unique for
each installation.
Following is an outline to guide the professional alarm installer
through the programming of the Control Panel.

Press logo to access

the Installer Toolbox

If you dont read anything else, read this outline!

Figure 45. The Home Screen

Use the following outline in conjunction with this copy of the

Installation and Programming Instructions to guide you through
the installation.
Because of the many programming options available with this
Control Panel, thoroughly reading this manual is very important.
Understanding the Control Panels programming structure will help
to save time during each installation.
At this stage, all the wireless and hardwired sensors should be
installed, and the Control Panel should be mounted, connected,
and powered-up.

Installer Toolbox can be

accessed here also

1. Start at the Home Screen.

Figure 46. Toolbox Screen Three

2. Press the logo at the lower right corner of the screen.

(The Installer Toolbox can also be accessed via
the third screen of the System Toolbox.)
3. Enter the Installer Code (default = 1561) to display the Installer Toolbox.
4. Press SYSTEM CONFIGURATION and begin
programming as described on Page 18.
5. USE THE INSTALLATION LOG SHEET TO RECORD
PROGRAMMED VALUES FOR THE SYSTEM.
6. After setting all the required programming values for the sensors and
the Control Panel, press END, then EXIT, to save the changes.
7. After the Control Panel restarts, press SECURITY, MENU,
TOOLBOX, enter the Master User Code (default = 1111), press
USER MANAGEMENT and setup the users codes. Be sure to
set a Duress Code as User #8. Press BACK when finished.

Figure 47. Installer Toolbox Screen

8. Press BRIGHTNESS / VOLUME and set the levels for the installation.
The volume setting DOES NOT affect the volume of alarm sounds.
9. Press to view the second toolbox screen.
10. Press BACKLIGHT TIMEOUT and set the display lighting timeout.
11. Press SET DATE and SET TIME and set the calendar and clock. (If the
GSM module is installed, the date and time are set automatically.)
12. Press the

button to return to the Home Screen.

After all setup and programming, refer to the Operation and

Users Guide for details on operating the system. Check off the
programmed options for the system in the Users Guide.

Figure 48. System Configuration Question Q-1

PROGRAMMING QUESTION

SIA CP-01 DEFAULT

RANGE

Q-1 Wireless Sensor Dialer Delay

30 Seconds

On or Off

Q-2 Wired Sensor Dialer Delay

30 Seconds

On or Off

Q-5 Exit Delay

60 Seconds

45-120 Seconds

SIA CP-01 Defaults

Q-6 Entry Delay #1

30 Seconds

30-240 Seconds

Several system programmable options have the defaults pre-set to

provide compliance with the Security Industry Association CP-01
Standard. All other system settings and functions that are required
to comply with SIA CP-01 are permanently programmed into
the Console and cannot be changed. Refer to the table for each
programmable option that has a required SIA CP-01 programming
default.

Q-7 Entry Delay #2

45 Seconds

30-240 Seconds

Be sure to instruct the subscriber on the proper operation of the

system, and leave the Users Guide at the installation site for
reference.

16

Q-10 Call Waiting Disable Code

No Default Code

0-6 Digits

Q-20 Swinger Shutdown Count

2 Trips

1-6 Trips

Q-26 Auto Stay

Enabled

Enabled or Disabled

Q-27 Exit Delay Restart

Enabled

Enabled or Disabled

Q-31 Cancel Time

5 Minutes

6-254 Minutes

Q-32 Cancel Display

Enabled

Enabled or Disabled

Q-35 Abort Window Dialer Delay

30 Seconds

15 or 45 Seconds

Q-78 Select Output

Follows Internal Sounder

See Q-78 for Options

Programming Question Table

Q#
Q-1

QUESTION
Select RF sensor # (01-48)
Select RF sensor (#) type

Q-1 SUB-QUESTIONS

Select RF sensor (#) equipment type

Q-2 SUB-QUESTIONS

Q-2

Q-3 SUB-QUESTIONS

Q-3

Q-4 SUB-QUESTIONS

Q-4

Q-5
Q-6
Q-7
Q-8
Q-9
Q-10
Q-11
Q-12
Q-13
Q-14
Q-15
Q-16
Q-17
Q-18
Q-19
Q-20
Q-21
Q-22
Q-23
Q-24
Q-25
Q-26
Q-27

Select RF sensor (#) equipment code

Enter RF sensor (#) other equipment code (0-9999)
Enter RF sensor (#) serial number (7 digits)
Select RF sensor (#) equipment age (0-1)
Select RF sensor (#) loop number (1-3)
Select RF sensor (#) dialer delay (0-1)
Construct RF sensor (#) voice descriptor
Select RF sensor (#) reports (0-1)
Select RF sensor (#) supervised (0-1)
Select RF sensor (#) chime (0-5)
Select wired sensor # (1-2)
Select wired sensor (#) type
Select wired sensor (#) equipment type
Enter wired sensor (#) equipment code (0-9999)
Select wired sensor (#) equipment age (0-1)
Select wired sensor (#) normal state
Select wired sensor (#) dialer delay (0-1)
Construct wired sensor (#) voice descriptor
Select wired sensor (#) reports (0-1)
Select wired sensor (#) chime (0-5)
Select fob # (1-8)
Select fob (#) used (0-1)
Select fob (#) equipment code (0000)
Enter fob (#) other equipment code (0-9999)
Enter fob (#) serial number (7 digits)
Select fob (#) equipment age (0-1)
Select fob (#) emergency key (0-4)
Select fob (#) key 2 can disarm (0-1)
Construct fob (#) voice descriptor
Select fob (#) arm no delay (0-1)
Select fob (#) key 4 output (0-2)
Select RF keypad # (1-4)
Select RF keypad (#) used (0-1)
Select RF keypad (#) equipment code
Enter RF keypad (#) other equipment code (0-9999)
Enter RF keypad (#) serial number (7 digits)
Select RF keypad (#) equipment age (0-1)
Select RF keypad (#) emergency keys (0-1)
Construct RF keypad (#) voice descriptor
Enter exit delay, in seconds (45-120)
Enter entry delay 1, in seconds (30-240)
Enter entry delay 2, in seconds (30-240)
Select dialer (0-1)
Enter dialing prefix (0-4 digits)
Enter call waiting disable code (0-6 digits)
Enter CS #1 phone number (0-25 digits)
Enter CS #1 account number (4 digits)
Select 2-way voice (0-2)
Select silent panic/burglary listen only (0-1)
Select dialing type (0-1)
Select police emergency key (0-2)
Select fire emergency key (0-1)
Select emergency key (0-1)
Select quick arming (0-1)
Select swinger shutdown count (1-6)
Select siren supervision time (0-3)
Enter CS lack of usage notification time (0-255)
Enter radio modem network failure time (0-255)
Select radio modem network failure causes trouble (0-1)
Select radio modem network failure reports (0-1)
Select auto stay (0-1)
Select exit delay restart (0-1)

DEFAULT
(00) unused
Varies by RF sensor type
(Only shown for some sensor types)
(0000) other
0 (Only shown if other is selected)
0000000
(0) new
Varies with sensor model selected
(1) enabled (except for fire & CO)
No default
(1) enabled
(1) enabled
(0) disabled
(00) unused
Varies by wired sensor type
(Only shown for some sensor types)
0
(0) new
(0) not used
(1) enabled
No default
(1) enabled
(0) disabled
(0) unused
(0000) other
0 (Only shown if other is selected)
0000000
(0) new
(0) disabled
(1) enabled
keyfob #
(0) disabled
(0) disabled
(0) unused
(0000) other
0 (Only shown if other is selected)
0000000
(0) new
(1) enabled
keypad #
60 seconds
30 seconds
45 seconds
(0) disabled
No default
No default
No default
No default
(1) stay on line
(1) enabled
(0) touch tone
(1) audible
(1) audible
(1) audible
(1) enabled
(2) two trips
(0) disabled
7 Days
30 minutes
(1) enabled
(1) enabled
(1) enabled
(1) enabled

Q#
Q-28
Q-29
Q-31
Q-32
Q-33
Q-34
Q-35
Q-36
Q-37
Q-38
Q-39
Q-40
Q-41
Q-42
Q-43
Q-44
Q-45
Q-46

QUESTION
Select quick exit (0-1)
Enter periodic test, in days (0-255)
Enter cancel time, in minutes (5-255)
Select cancel display (0-1)
Select cross sensor 47-48 (0-1)
Enter cross sensor timeout, in seconds (10-120)
Select abort window dialer delay (0-2)
Select burglary bell cutoff (0-4)
Select fire bell cutoff (0-4)
Enter time to detect AC loss, in minutes (0-30)
Select random AC loss report time (0-1)
Enter CS #2 phone number (0-25 digits)
Enter CS #2 account number (4 digits)
Select remote control phone (0-3)
Enter installer code (4 digits)
Select lock installer programming (0-2)
Select lock default programming (0-2)

Select trouble doesnt sound at night (0-1)

Select trouble resound after holdoff (0-7)
Enter download csid (6 digits)
Select programming mode entry reports to CS (0-1)
Select trouble reports to CS (0-1)
Select manual bypass reports to CS (0-1)
Select AC loss reports to CS (0-1)
Select system low battery reports to CS (0-1)
Select RF low battery reports to CS (0-1)
Select opening reports to CS (0-1)
Select closing reports to CS (0-1)
Select alarm restore reports to CS (0-1)
Select trouble restore reports to CS (0-1)
Select bypass restores reports to CS (0-1)
Select AC restore reports to CS (0-1)
Select system low battery restore reports to CS (0-1)
Select RF low battery restores reports to CS (0-1)
Select phone fail detect (0-1)
Select smart test reports (0-1)
Select RF jam causes trouble (0-1)
Select daylight saving (0-1)
Select daylight saving start month (01-12)
Select daylight saving start Sunday (1-7)
Select daylight saving end month (01-12)
Select daylight saving end Sunday (1-7)
Select system tamper causes trouble (0-1)
Select quick bypass (0-1)
Select disarming keyfob after alarm (alert) (0-1)
Select keyfob arm / disarm confirmation (0-1)
Select auto unbypass for manual bypass (0-1)
Select force bypass reports (0-1)
Select event log (0-3)
Select output (00-10)
Select Z-Wave feature (0-3)
Select Z-Wave switches feature (0-1)
Select Z-Wave thermostats feature (0-1)
Select Z-Wave door locks feature (0-1)
Select temperature display units (0-1)
Select services require master code (0-1)
Select master user access to zwave toolbox (0-1)
Select disable siren after two-way audio (0-1)
Select keyfob/remote arming mode on system not
Q-87
ready (0-2)
Q-88 Select siren mode (0-1)
Default set for SIA CP-01 compliance
Q-47
Q-48
Q-49
Q-50
Q-51
Q-52
Q-53
Q-54
Q-55
Q-56
Q-57
Q-58
Q-59
Q-60
Q-61
Q-62
Q-63
Q-64
Q-65
Q-66
Q-67
Q-68
Q-69
Q-70
Q-71
Q-72
Q-73
Q-74
Q-75
Q-76
Q-77
Q-78
Q-79
Q-80
Q-81
Q-82
Q-83
Q-84
Q-85
Q-86

DEFAULT
(1) enabled
30 days
5 minutes
(1) enabled
(0) disabled
10 seconds
(1) 30 seconds
(0) 4 minutes
(0) 4 minutes
10 minutes
(1) enabled
No default
No default
(3) data and voice
1561
(0) disabled
(0) default all
(1) enabled
(0) disabled
000000
(0) disabled
(1) enabled
(0) disabled
(1) enabled
(1) enabled
(1) enabled
(0) disabled
(0) disabled
(0) disabled
(1) enabled
(0) disabled
(1) enabled
(1) enabled
(1) enabled
(0) disabled
(0) disabled
(0) disabled
(1) enabled
(03) March
(2) 2nd
(11) November
(1) 1st
(1) enabled
(0) disabled
(0) disabled
(0) disabled
(1) enabled
(0) disabled
(3) all events
(11) follows internal sounder alarm
(1) disabled but visible
(0) disabled
(0) disabled
(0) disabled
(0) degrees Fahrenheit
(0) disabled
(0) disabled
(0) disabled
(0) auto-bypass with zone
participation on restore
(0) sound for burglary and fire/CO

For UL985 Installations, this feature must be disabled

17

System Sensor Types

Each sensor (wireless or wired) installed in the system is
programmed to a specific sensor number and sensor type (zone).
The sensor number identifies the specific sensor when it is
displayed on the Control Panel, recorded in the event log, or
reported to the Central Station. This allows pin-point information
about any sensor in the system.
The sensor type determines how and when the Control Panel
responds to signals from the sensor. Some sensors are armed
all the time, others are armed only in certain arming levels, some
cause Central Station reports any time they are activated. The
sensors type, along with other programming options, determine
this.

Sensor Types (Zones)

(00) Unused
This is the setting for unused sensor numbers that do not have a sensor
programmed into them. No system action occurs at any time from this sensor
type.

(01) Exit/Entry 1
This sensor type is reserved for doors that are used for exit and entry of the
protected premises. When the system is armed in the Away Mode or Stay Mode,
the Exit Delay timer starts. There is an Exit Delay regardless of whether the
system is armed in Stay Mode or Away Mode. When the Exit Delay timer expires,
the system is fully armed.
With the system fully armed, when this type of sensor is triggered, the Entry
Delay #1 timer starts. The system must be disarmed before the Entry Delay #1
time expires, or an alarm will occur.
If the Entry Delay is turned off during arming, the exit/entry delay sensors will act
as non-delayed instant sensors at the end of Exit Delay.

(02) Exit/Entry 2
This sensor type operates the same as the Exit/Entry 1 sensor type except it will
start the Entry Delay #2 timer. This provides a method of having a longer Entry
Delay on certain openings, such as a garage door, to provide the user more time
to disarm the system.

(03) Perimeter
This sensor type is for perimeter doors and windows that will not be used to enter
or exit the protected premises while the system is armed.
An instant alarm will occur when this type of sensor is triggered with the system
armed in either the Stay Mode or Away Mode.

(04) Interior Follower

This sensor type is for interior sensors such as motion detectors, mat switches,
interior doors, and other sensors that detect human presence inside the protected
premises.
This type of sensor is called a follower due to its action when the system is
armed in the Away Mode. After the Exit Delay expires and the system is armed, if
an interior follower sensor is triggered, an instant alarm will occur. If an exit/entry
delay sensor is triggered first, the interior follower sensor will also be delayed.
Interior follower sensors are always bypassed and not active when the system is
armed in Stay Mode. This allows the premises to be occupied while still protecting
the perimeter.

(05) Day Zone

This sensor type is the same as a perimeter zone, except when the system is
disarmed, a violation displays a trouble alert on the Consoles display.
Common uses for this sensor type are protection of sensitive areas that require
notification and possibly a Central Station trouble report, but not an alarm when
the system is disarmed.

18

(06) 24-hour Silent Alarm

This sensor type is active independent of the system arming status. The code
for silent panic is sent to the Central Station, but for safety, there are no visual or
audible indications locally that this sensor type has been triggered.

(07) 24-hour Audible Alarm

This sensor type is continuously armed 24-hours a day. A sensor programmed to
this type will trigger a local alarm and the bell output regardless of the mode the
system is in. Typical use would be an audible panic alarm.

(08) 24-hour Auxiliary Alarm

This sensor type is continuously armed 24-hours a day. A sensor programmed
to this type will trigger an alarm regardless of the mode the system is in. The bell
output will not activate, but the local sounder will continue until its acknowledged
at the Control Panel. Typical use would be for a monitoring device such as a flood
or temperature sensor. There is no timeout for the internal sounder, it will continue
until a User Code is entered.

(09) 24-hour Fire

This sensor type is continuously armed 24-hours a day. A sensor programmed
to this type will trigger the local alarm fire sounder and the bell output regardless
of the mode the system is in. Typical use would be for wireless smoke detectors.
This sensor type is always active and cannot be bypassed.

(10) Interior with Delay

This sensor type operates as a delayed sensor when the system is armed in the
Away Mode, and when triggered, will start the Entry Delay #1 timer. If the system
is armed in Away Mode with no Entry Delay (armed instant), this sensor type will
trigger an instant alarm.
If the system is armed in Stay Mode (or Stay Mode with no Entry Delay), this
sensor type will be bypassed.

(14) 24-hour Carbon Monoxide

This sensor type is continuously armed 24-hours a day. A sensor programmed to
this type will trigger the local alarm pulse sounder and the bell output regardless
of the mode the system is in. Typical use would be for wireless carbon monoxide
detectors. This sensor type is always active and cannot be bypassed.

(16) 24-hour Fire with Verification

This sensor type is continuously armed 24-hours a day. A sensor programmed to
this type can trigger the local alarm fire sounder and the bell output regardless
of the mode the system is in. Typical use would be for wireless smoke detectors.
This sensor type is always active and cannot be bypassed.
For verification, this sensor type must be violated twice in two minutes, or remain
violated for 30 seconds. If any other fire sensor (verified sensor type or not)
violates within two minutes, both sensors will cause a fire alarm.

(23) No Response Type

This sensor type is a special zone that can be monitored for activity or inactivity
by the Central Station. It does not affect security system status.

(24) Silent Burglary

This sensor type is for silent triggering the burglary alarm with perimeter doors
and windows that will not be used to enter or exit the protected premises while
the system is armed. The Control Panels sounder and the bell output will not
activate.
An instant silent alarm will occur when this type of sensor is triggered with the
system armed in either the Stay Mode or Away Mode.
Indicates Sensor types that are not allowed for hardwired
loops.

System Vocabulary Table

#
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069

WORD
ABORT
AC
ACCESS
ALARM
AND
ANNOUNCEMENT
AREA
ARM
ARMED
ARMING
AT
ATTIC
AUDIO
AUTO
AUTOMATION
AUXILIARY
AWAY
BABYS
BACK
BASEMENT
BATHROOM
BATTERY
BEDROOM
BONUS
BREAK
BUTTON
BYPASS
BYPASSED
CABINET
CANCEL
CARBON MONOXIDE
CELLAR
CELLULAR
CELL RADIO
CENTER
CHECK
CHEST
CHILDRENS
CHIME
CLOSET
CODE
COMMUNICATIONS
COMPUTER
CONTROL
COOL
CRAWL
CURRENT
DAY
DEGREES
DEN
DETECTOR
DIM
DINING
DISARM
DISARMED
DOCK
DOOR
DOWNSTAIRS
DRIVEWAY
EAST
EIGHT
EIGHTEEN
EIGHTY
ELECTRIC
ELEVEN
EMERGENCY
ENTER
ENTRANCE

#
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137

WORD
ENTRY
ERROR
EXERCISE
EXIT
EXIT NOW
EXTERIOR
EXTERNAL
FAILURE
FAMILY
FAN
FIFTEEN
FIFTY
FIRE
FIRE ALERT
FIRE DETECTOR
FIRST
FIVE
FLOOD
FLOOR
FLUID
FOIL
FOR
FORTY
FOUR
FOURTEEN
FOURTH
FREEZE
FREEZER
FRONT
FURNACE
GAME
GARAGE
GAS
GLASS
GLASS BREAK
GUEST
GUN
HALL
HALLWAY
HANGING
HANG UP
HEAT
HIGH
HOME
HOUSE
ICE
INSIDE
INSTANT
INTERIOR
INTRUSION
IS
KEY
KEYFOB
KEYPAD
KIDS
KITCHEN
LAUNDRY
LEFT
LEVEL
LIBRARY
LIGHT
LIGHTS
LIQUOR
LIVING
LOADING
LOCK
LOFT
LOW

#
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205

WORD
MAIN
MAINTENANCE
MASTER
MEDICAL
MEDICINE
MENU
MIDDLE
MONITOR
MOTION
MOTION DETECTOR
MUD
NINE
NINETEEN
NINETY
NORTH
NOT
NOT READY
NO DELAY
NO ENTRY DELAY
NURSERY
OFF
OFFICE
ON
ONE
ONE HUNDRED
OUTPUT
OUTSIDE
PANEL
PANIC
PANTRY
PATIO
PERIMETER
PHONE LINE
PLAY
POLICE
POOL
POUND
POWER
PRESS
PREVIOUS
PUMP
RADIO
READY
REAR
RELAY
REMOTE
REPEAT
RF JAM
RIGHT
ROOM
SAFE
SECOND
SECURITY
SENSOR
SENSORS
SESSION
SET
SEVEN
SEVENTEEN
SEVENTY
SHED
SHOP
SIDE
SILENT
SIREN
SIX
SIXTEEN
SIXTY

#
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271

WORD
SKYLIGHT
SLIDING
SMOKE
SOUNDER
SOUTH
SPACE
SPARE
STAIRS
STAR
STATUS
STAY
STOP
STORAGE
STUDY
SUMP
SUPERVISION
SYSTEM
TAMPER
TEMPERATURE
TEN
TERMINATED
THERMOSTAT
THIRD
THIRTEEN
THIRTY
THREE
TO
TOOL
TRANSMITTED
TRANSMITTER
TROUBLE
TURN
TWELVE
TWENTY
TWO
UNLOCK
UPPER
UPSTAIRS
USER
UTILITY
VALVE
VOICE
WALL
WATER
WEST
WINDOW
WIRELESS
YARD
ZERO
ZONE
BALCONY
COURTYARD
DECK
DETACHED
OVERHEAD
REFRIGERATOR
SERVICE
SUNROOM
WAREHOUSE
GATE
APARTMENT
FOYER
TV
VIDEO
PORCH
CORNER

19

Installer Programming
RF Sensor Programming
RF Sensor Programming Outline
The Control Panel can be programmed with up to 48 RF sensors
of different types. In addition to the 48 multi-purpose RF sensors,
eight RF remote control key fobs and four RF remote control
keypads can be programmed into the system.

Refer to Figure 49 for an outline of the steps required to program

RF sensors into the Control Panel. The options that can be set for
each RF sensor are:
Sensor Number Sensor number 01-48
Sensor Type Exit/entry, perimeter, interior, etc.
Sensor Equipment Type Certain sensor
types will ask for equipment type

Programming the RF sensors into the Control Panel involves

selecting the sensor number for a particular device, selecting the
RF sensor type, setting or learning the RF sensors serial number,
and selecting the other options for the sensor.

Sensor Equipment Code Sensor model

(door/window, PIR, smoke detector, etc.)
Sensor Other Equipment Code Enter special
equipment code (only shown for sensors set as other)
Q-1 SUB-QUESTIONS

RF sensors #1 - #48 report as system sensors #1 - #48

Sensor Serial # Serial number labeled on sensor;

manually enter or learn by sending signal
Sensor Equipment Age New install or existing sensor
Sensor Loop Number Built-in contacts or
external contacts on DW10 door/window sensor
Sensor Dialer Delay Delayed or instant
communicator reports for the sensor (delay
time is set by dialer abort window)
Sensor Voice Descriptor Name assigned to the sensor
Sensor Reports Communicator reports or
no communicator reports for the sensor
Sensor Supervised Control Panel checks for status
reports from the sensor, or does not check for status reports
Sensor Chime Select voice announcement
and chime options for the sensor

20

Installer Programming
RF SENSOR PROGRAMMING (Q-1) OUTLINE
STEP DOWN
THROUGH OPTIONS

SELECT OPTION WITH

THESE KEYS

ENTER ON KEYPAD OR PRESS

SELECT RF SENSOR #

PRESS

FOR NEXT OPTION

PRESS

TO SELECT FROM LIST

OR PRESS SKIP TO JUMP TO Q-2
ENTER ON KEYPAD OR PRESS

ENTER ON KEYPAD OR PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

OR

ENTER ON KEYPAD

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

ENTER RF SENSOR
SERIAL NUMBER

PRESS

FOR NEXT OPTION

shift

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT RF SENSOR
DIALER DELAY

PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

CONSTRUCT RF SENSOR
VOICE DESCRIPTOR

learn

ENTER ON KEYPAD OR PRESS

SELECT RF SENSOR
LOOP NUMBER

PRESS

THEN

AND SEND SIGNAL FROM SENSOR

SELECT RF SENSOR
EQUIPMENT AGE

PRESS

Figure 50. RF Sensor Summary Screen

TO SELECT FROM LIST

FOR NEXT OPTION

ENTER RF SENSOR
OTHER EQUIPMENT CODE
(ONLY FOR "OTHER" EQUIPMENT)
PRESS

Pressing SKIP goes to question number Q-2 (wired sensor programming).

TO SELECT FROM LIST

FOR NEXT OPTION

SELECT RF SENSOR
EQUIPMENT CODE

PRESS

The EDIT CURRENT and EDIT NEXT buttons return to sensor

programming.

OR

SELECT RF SENSOR
EQUIPMENT TYPE
(ONLY FOR SOME SENSOR TYPES)
PRESS

After setting all the options for a sensor, the RF sensor summary
screen is displayed. The screen can also be displayed for
programmed sensors during RF sensor program editing by
pressing the SUM button.
The and arrow buttons step through the RF sensor numbers.

OR

SELECT RF
SENSOR TYPE

RF Sensor Summary Screen

PRESS insert FOR EACH WORD

ENTER ON KEYPAD OR PRESS
OR

PRESS

FOR NEXT OPTION

TO SELECT FROM LIST

ENTER ON KEYPAD OR PRESS

SELECT RF SENSOR
REPORTS

PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT RF SENSOR
SUPERVISED

PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT RF SENSOR
CHIME

OR
TO SELECT FROM LIST

PRESS

TO FINISH FOR THIS SENSOR, THEN

edit
next

FOR NEXT SENSOR, OR skip FOR Q2

Figure 49. RF Sensor Programming Outline

21

Installer Programming
RF Sensor Programming Steps

Q-1

Select RF sensor # (01-48)

Up to 48 wireless RF sensors can be used with each Control Panel. The options
for each sensor are programmed with sub-option questions.
Begin by entering the RF sensor number or
select it using the or arrows.
After selecting the sensor number, program the sensor details by
using the and arrows to select each of the sub-options.
NOTE: To skip RF sensor programming, press SKIP to jump from
question Q-1 to question Q-2 (wired sensor programming).

Select RF sensor (#) equipment code

DEFAULT: (0000) other
The equipment code is a 4-digit code that is assigned to the model of sensor
being used. The Control Panel will display a list of sensor models and their
associated 4-digit equipment code.
Select the model of RF sensor being programmed for this
sensor number using the or arrows, or enter the
equipment code number directly on the keypad.
Select (0000) other if the sensor model is not shown on the list. The
equipment code for the sensor can be entered using the next sub-question.
SENSOR EQUIPMENT CODES

Select RF sensor (#) type

DEFAULT: Unused (00)

(0000) other

Each RF sensor needs to be assigned to a sensor type. The sensor type

determines how and when the Control Panel responds to signals from the
sensor.

(0863) DW20R-345 recessed door contact

Use this step to assign the sensor to a sensor type (zone).

(0895) SMKT2-345 GE smoke/heat detector (USA/Canada)

(0862) DW10-345 thin door/window contact

Select the sensor type that matches the sensors function using the
or arrows, or enter the sensor type number directly on the keypad.
SENSOR TYPES

(0864) GB1-345 glass break detector

(1058) SMKT3-345 2gig smoke detector
(0872) SMKE1-345 smoke detector (USA)
(0871) SMKE1-345C smoke detector (Canada)

(00) unused

(0868) PANIC1-345 panic button remote

(01) exit/entry 1

(0860) CO1-345 CO detector (USA)

(02) exit/entry 2

(0859) CO1-345C CO detector (Canada)

(03) perimeter

(1026) CO3-345 2gig CO detector (USA/Canada)

(04) interior follower

(0873) TAKE-345 takeover module

(05) day zone

(0637) HW D/W 5816

(06) 24-hour silent alarm

(0470) HW R-D/W 5818MNL

(07) 24-hour audible alarm

(0533) HW PIR 5890

(08) 24-hour auxiliary alarm

(0530) HW PIR 5894PI

(09) 24-hour fire

(0519) HW Glass Break 5853

(0589) HW Smoke 5808W3

(10) interior with delay

(14) 24-hour carbon monoxide
(16) 24-hour fire with verification

(0624) HW Flood Sensor 5821

(0655) Existing door/window contact

(24) silent burglary

(0609) Existing motion detector

(0475) Existing glass break detector

Select RF sensor (#) equipment type

DEFAULT: Varies by RF sensor type

(0616) Existing smoke detector

NOTE: This question is only displayed when certain sensor types are selected.
The equipment type selection will affect the sensors extended reporting code.

The following sensor types require equipment type selection:

SENSOR TYPE

(0557) HW Heat Sensor 5809

(0491) HW Panic Pendant 5802MN2

(23) no response type

EQUIPMENT TYPES AVAILABLE

(04) interior follower

(1) = motion

(2) = contact

(06) 24-hour silent alarm

(1) = contact

(11) = emergency

(07) 24-hour audible alarm

(1) = contact

(11) = emergency

(08) 24-hour auxiliary alarm

(1) = contact (6) = freeze (8) = water

(10) = temperature (11) = emergency

(10) interior with delay

(1) = motion

(2) = contact

(23) no response type

(1) = contact

(2) = motion

Select the equipment type that matches the sensor equipment using the
or arrows, or enter the equipment type number directly on the keypad.

22

(0869) PIR1-345 PIR with pet immunity

(0692) Existing CO detector

(0708) Existing heat sensor
(0556) Existing flood/temp sensor
(1061) GARAGE01 Resolution Products tilt sensor
(1063) DBELL1-345 2gig doorbell

Enter RF sensor (#) other equipment code (0-9999)

DEFAULT: 0
NOTE: This question is only displayed if (0000) other
is selected for a sensors equipment code.

The equipment code is a 4-digit code that is assigned to the model of sensor being
used. If new equipment becomes available, the new equipment code should be
entered here if the new equipment is not listed in the Sensor Equipment Codes
table above.
Enter the equipment code number directly on the keypad for the
RF sensor. (Enter 0 if the new equipment code is unknown.)

Installer Programming
Enter RF sensor (#) serial number (7 digits)
DEFAULT: 0000000

Construct RF sensor (#) voice descriptor

DEFAULT: No default

RF sensor serial numbers can be manually entered or learned from the sensor.

The voice descriptors are the words the Control Panel will announce for this RF
sensor if this sensor is programmed for voice annunciation. Up to five words are
allowed.

For manual entry, enter the sensor number that was logged for the sensor
being programmed. Use the SHIFT button to access alpha characters.
For automatic entry, press SHIFT, then press LEARN. The
Control Panel will wait for a sensor transmission. Trigger
the sensor being programmed and the Control Panel will
beep four times and learn the sensors serial number.
If the sensor being learned is already in memory, the Control Panel will display a
sensor learning failure screen when the programming changes are being saved.
For certain sensors with more than two loops, the tamper switch must be used to
send a signal to the Control Panel during sensor learning. First press of tamper
switch will learn as Loop #1, the second press of tamper switch will learn as
Loop #2, the third press of tamper switch will learn as Loop #3. Wait 15 seconds
between each press of the tamper switch. The programmed loop number of
the sensor in the Control Panel may need changing to suit the operation of the
device. See the Installation Instructions of the sensor for details.

Select RF sensor (#) equipment age (0-1)

DEFAULT: New (0)
The Control Panel can be used with new or existing RF sensors.
If this RF sensor is new for the installation, leave the default of new (0).
If this RF sensor is already installed, select existing (1).

Press INSERT to place a word from the vocabulary into the data entry field.
Use the or arrows to scroll through the words, or enter the
words 3-digit index number (see vocabulary table on Page 19).
Press INSERT again for the next word. Up to five words are allowed.
To move between words, press the FWD and BACK buttons.
To remove a word, press DELETE.

Select RF sensor (#) reports (0-1)

DEFAULT: Enabled (1)
RF sensors can trigger a report to the Central Station or not.
The default (1) enables reporting for this RF sensor number.
To prevent reporting for this RF sensor number, select disabled (0).

Select RF sensor (#) supervised (0-1)

DEFAULT: Enabled (1)
When a sensor is set to supervised, the Control Panel will expect regular timed
signals from this sensor or else a sensor supervisory trouble alert will occur.
The default (1) allows supervision for this RF sensor.
To turn off supervision for this RF sensor, select disabled (0).

NOTE: If the RF sensor has more than one loop and is being
programmed into multiple sensor numbers to support the loops,
set only one loop as new and the other loops as existing. This
will prevent incorrect inventory of the installed sensors.

NOTE: Portable sensors such as panic buttons should not be set as

supervised if the sensor will be removed from the premises at times.

Select RF sensor (#) loop number (1-3)

DEFAULT: Varies with sensor model selected

Select RF sensor (#) chime (0-5)

DEFAULT: Disabled (0)

2GIG-DW10 door/window sensors have two inputs: an internal magnetic contact

and an external normally closed hardwired input. Either or both sensor inputs can
be used. Some sensors have three loop inputs.
When using both the internal magnetic contact AND the external input,
THE MAGNETIC CONTACT AND THE EXTERNAL CONTACT NEED TO
BE ASSIGNED A DIFFERENT RF SENSOR NUMBER. BOTH SENSOR
NUMBERS WILL SHARE THE SAME SENSOR SERIAL NUMBER.
When programming the sensor to use the built-in
magnetic contact, set the loop number to (2).
When programming the sensor to use its hardwired
input, set the loop number as (1).
When programming a 3-loop sensor to use an
additional input, set the loop number as (3).
When entering the sensor number for the sensors loop two
or three, the PASTE button can be used to recall the last
programmed sensors serial number. (The sensor number
will be filled in automatically if LEARN is used.)

Each RF sensor can be set to sound a ding-dong chime and/or sound its voice
descriptor when the sensor is triggered. This step determines the initial setting
for the sensor. The end user can change the chime setting for sensors using
CHIME SETUP in the User Toolbox.
The default (0) disables the chime for this RF sensor.
If a chime and/or voice is required for this RF sensor,
choose one of the other chime options:
RF SENSOR CHIME
(0) disabled

(7) ding-ding with voice

(1) voice only

(8) ding-dong #3

(2) ding-dong with voice #1

(9) ding-dong with voice #3

(3) ding-dong #2

(10) chime #1

(4) ding-dong with voice #2

(11) chime #1 with voice #1

(5) ding-dong #1

(12) chime #2

(6) ding-ding

(13) chime #2 with voice #2

Select RF sensor (#) dialer delay (0-1)

DEFAULT: Enabled (1) (Required SIA CP-01 Default)
RF sensors can trigger the communicator immediately or after a delay. The delay
time is set by the abort window dialer delay programming question Q-35 (the
default delay is 30 seconds).
The default (1) causes delayed dialing for this RF sensor number.
For immediate dialing for this RF sensor number, select disabled (0).
NOTE: This setting for CO and smoke detectors is automatically set to
disabled (0), and this sub-question is skipped for these sensor types.
NOTE: This default can be changed without affecting SIA CP-01 compliance.

23

Installer Programming
Wired Sensor Programming
Wired Sensor Programming Outline
The Control Panel can be programmed with up to two wired
sensors. The wired sensors are hardwired contact loops connected
to the loop input terminals on the Control Panels terminal strip.
NOTE: WIRED SENSORS CANNOT BE USED FOR A
CO OR FIRE SENSOR LOOP!!!

WIRED SENSOR PROGRAMMING (Q-2) OUTLINE

STEP DOWN
THROUGH OPTIONS

Programming the wired sensors into the Control Panel involves

selecting the sensor number (1 or 2), selecting the wired sensor
type, setting the equipment code, loop type (open, closed, or
end-of-line resistor), and selecting the other options for the
sensor.
Wired sensors #1 & #2 report as system sensors #49 & #50

ENTER ON KEYPAD OR PRESS

SELECT WIRED SENSOR #

PRESS

WIRED SENSOR REPORTING CODES

Wired sensor #1

Reports as sensor #49

Wired sensor #2

Reports as sensor #50

Refer to Figure 52 for an outline of the steps required to program

wired sensors into the Control Panel. The options that can be set
for each wired sensor are:

SELECT OPTION WITH

THESE KEYS

FOR NEXT OPTION

OR
TO SELECT FROM LIST
OR PRESS SKIP TO JUMP TO Q-3
ENTER ON KEYPAD OR PRESS

SELECT WIRED
SENSOR TYPE

PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

SELECT WIRED SENSOR

EQUIPMENT TYPE
(ONLY FOR SOME SENSOR TYPES)

ENTER ON KEYPAD OR PRESS

OR

Wired Sensor Number Sensor number 1 or 2

Wired Sensor Type Exit/entry, perimeter, interior, etc.

PRESS

Wired Sensor Equipment Type Certain

sensor types will ask for equipment type

Q-2 SUB-QUESTIONS

Wired Sensor Equipment Code 4-digit

equipment code that matches installed sensor

ENTER WIRED SENSOR

EQUIPMENT CODE

PRESS

Wired Sensor Equipment Age

New install or existing sensor

Wired Sensor Voice Descriptor Name

assigned to the sensor

PRESS

PRESS

The and arrow buttons step through the wired sensor numbers.

ENTER ON KEYPAD OR PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT WIRED SENSOR

DIALER DELAY

Wired Sensor Chime Select voice announcement

and chime options for the sensor
After setting all the options for a sensor, the wired sensor
summary screen is displayed. The screen can also be displayed
for programmed sensors during wired sensor program editing by
pressing the SUM button.

FOR NEXT OPTION

SELECT WIRED SENSOR

NORMAL STATE

Wired Sensor Reports Communicator reports

or no communicator reports for the sensor

Wired Sensor Summary Screen

ENTER ON KEYPAD

SELECT WIRED SENSOR

EQUIPMENT AGE

Wired Sensor Normal State normally

open, closed, or end-of-line resistor loop
Wired Sensor Dialer Delay Delayed or
instant communicator reports for the sensor
(delay time is set by dialer abort window)

TO SELECT FROM LIST

FOR NEXT OPTION

PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

CONSTRUCT WIRED SENSOR

VOICE DESCRIPTOR

PRESS insert FOR EACH WORD

ENTER ON KEYPAD OR PRESS
OR

PRESS

The EDIT CURRENT and EDIT NEXT buttons return to sensor

programming.

TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT WIRED SENSOR

REPORTS

OR

Pressing SKIP goes to question Q-3 (key fob programming).

PRESS

TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT WIRED SENSOR

CHIME

OR
TO SELECT FROM LIST

PRESS

Figure 51. Wired Sensor Summary Screen

24

TO FINISH FOR THIS SENSOR, THEN

edit
next

FOR NEXT SENSOR, OR skip FOR Q3

Figure 52. Wired Sensor Programming Outline

Installer Programming
Wired Sensor Programming Steps

Q-2

Select wired sensor # (1-2)

Two hardwired loops can be used as sensors with each Control Panel. The
options for each wired sensor are programmed with sub-option questions.
Begin by entering the wired sensor number or
select it using the or arrows.
After selecting the wired sensor number, program the wired sensor
details by using the and arrows to select each of the sub-options.

Select wired sensor (#) normal state

DEFAULT: Not used (0)
The two hardwired loops can be wired for normally open (N/O) or normally closed
(N/C) contacts, or for end-of-line (EOL) resistor.
The default (0) disables this wired sensor.
To use this wired sensor, select the way the loop is wired:
WIRED SENSOR NORMAL STATE
(0) not used

NOTE: To skip wired sensor programming, press SKIP to jump

from question Q-2 to question Q-3 (RF key fob programming).

(1) closed
(2) open
(3) end-of-line resistor

Select wired sensor (#) type

DEFAULT: Unused (00)
Each wired sensor needs to be assigned to a sensor type.
Select the sensor type that matches the wired sensors function using the
or arrows or enter the sensor type number directly on the keypad.
SENSOR TYPES
(00) unused
(01) exit/entry 1
(02) exit/entry 2
(03) perimeter
(04) interior follower
(05) day zone
(06) 24-hour silent alarm
(07) 24-hour audible alarm
(08) 24-hour auxiliary alarm
(10) interior with delay
(23) no response type
(24) silent burglary

Select wired sensor (#) equipment type

DEFAULT: Varies by wired sensor type
NOTE: This question is only displayed when certain sensor types are selected.
The equipment type selection will affect the sensors extended reporting code.

The following sensor types require equipment type selection:

SENSOR TYPE
(04) interior follower
(06) 24-hour silent alarm
(07) 24-hour audible alarm
(08) 24-hour auxiliary alarm
(10) interior with delay
(23) no response type

EQUIPMENT TYPES AVAILABLE

(1) = contact (2) = motion
(1) = contact (11) = emergency
(1) = contact (11) = emergency
(1) = contact (6) = freeze (8) = water
(10) = temperature (11) = emergency
(1) = contact (2) = motion
(1) = contact (2) = motion

Select the equipment type that matches the sensor equipment using the
or arrows, or enter the equipment type number directly on the keypad.
NOTE: This Control Panel does not provide auxiliary accessory output power.
Connecting a hardwire PIR using equipment type motion will require
an external stand-alone battery backed-up power supply for the PIR.

Select wired sensor (#) equipment code (0-9999)

DEFAULT: (0)
The wired sensor equipment code defines the sensors manufacturer and type.
Enter the 4-digit equipment code for the sensor.

Select wired sensor (#) dialer delay (0-1)

DEFAULT: Enabled (1) (Required SIA CP-01 Default)
Wired sensors can trigger the communicator immediately or after a delay. The
delay time is set by the abort window dialer delay programming question Q-35
(the default delay is 30 seconds).
The default (1) causes delayed dialing for this wired sensor number.
For immediate dialing for this wired sensor number, select disabled (0).
NOTE: This default can be changed without affecting SIA CP-01 compliance.

Construct wired sensor (#) voice descriptor

DEFAULT: No default
The voice descriptors are the words the Control Panel will announce for this wired
sensor if this wired sensor is programmed for voice annunciation. Up to five words
are allowed.
Press INSERT to place a word from the vocabulary into the data entry field.
Use the or arrows to scroll through the words, or enter the
words 3-digit index number (see vocabulary table on Page 19).
Press INSERT again for the next word. Up to five words are allowed.
To move between words, press the FWD and BACK buttons.
To remove a word, press DELETE.

Select wired sensor (#) reports (0-1)

DEFAULT: Enabled (1)
Wired sensors can trigger a report to the Central Station or not.
The default (1) enables reporting for this wired sensor number.
To prevent reporting for this wired sensor number, select disabled (0).

Select wired sensor (#) chime (0-5)

DEFAULT: (0) Disabled
Each wired sensor can be set to sound a ding-dong chime and/or sound its
voice descriptor when the sensor is triggered.
The default (0) disables the chime for this wired sensor.
If a chime and/or voice is required for this wired sensor,
choose one of the other chime options:
WIRED SENSOR CHIME
(0) disabled

(7) ding-ding with voice

(1) voice only

(8) ding-dong #3

(2) ding-dong with voice #1

(9) ding-dong with voice #3

Select wired sensor (#) equipment age (0-1)

DEFAULT: New (0)

(3) ding-dong #2

(10) chime #1

(4) ding-dong with voice #2

(11) chime #1 with voice #1

The Control Panel can be used with new or existing wired sensors.

(5) ding-dong #1

(12) chime #2

(6) ding-ding

(13) chime #2 with voice #2

If this wired sensor is new for the installation, leave the default of new (0).
If this wired sensor is already installed, select existing (1).

25

Installer Programming
RF Key Fob Programming

KEY FOB PROGRAMMING (Q-3) OUTLINE

STEP DOWN
THROUGH OPTIONS

RF Key Fob Programming Outline

SELECT OPTION WITH

THESE KEYS

The Control Panel can be programmed with up to eight RF remote

control key fobs.
Programming the RF key fobs into the Control Panel involves
selecting the sensor number for a particular device, setting or
learning the RF key fobs serial number, and selecting the other
options for the sensor.

ENTER ON KEYPAD OR PRESS

SELECT KEY FOB #

PRESS

RF key fobs #1 - #8 report as system sensors #51 - #58

for opening/closing, emergency, and low battery reports.

Reports as sensor #51

RF key fob #2

Reports as sensor #52

RF key fob #3

Reports as sensor #53

RF key fob #4

Reports as sensor #54

RF key fob #5

Reports as sensor #55

RF key fob #6

Reports as sensor #56

RF key fob #7

Reports as sensor #57

RF key fob #8

Reports as sensor #58

Refer to Figure 54 for an outline of the steps required to program

RF key fobs into the Control Panel. The options that can be set for
each RF key fob are:

Q-3 SUB-QUESTIONS

Key Fob Number Key fob number 1-8

Key Fob Used Key fob used or not
Key Fob Equipment Code Key fob model
Key Fob Other Equipment Code Enter special
equipment code (only shown for key fobs set as other)
Key Fob Serial # Serial number labeled on key
fob; hand enter or learn by sending signal
Key Fob Equipment Age New unit or existing key fob
Key Fob Emergency Key Choose
function of double-press on top buttons
Key Fob Can Disarm Choose whether a
key fob is allowed to disarm the system
Key Fob Voice Descriptor Name assigned to the key fob
Key Fob Arm No Delay Choose if key fob
will arm instantly without an Exit Delay
Key Fob Key 4 Output Select action
for key fob auxiliary button

PRESS

ENTER ON KEYPAD OR PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT KEY FOB

EQUIPMENT CODE
PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER KEY FOB

OTHER EQUIPMENT CODE
(ONLY FOR "OTHER" EQUIPMENT)
PRESS

ENTER ON KEYPAD

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

ENTER KEY FOB

SERIAL NUMBER
PRESS

FOR NEXT OPTION

shift

PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT KEY FOB

KEY 2 CAN DISARM
PRESS

After setting all the options for a sensor, the key fob summary screen
is displayed. The screen can also be displayed for programmed key
fobs during key fob program editing by pressing the SUM button.

OR
TO SELECT FROM LIST

FOR NEXT OPTION

CONSTRUCT KEY FOB

VOICE DESCRIPTOR

learn

ENTER ON KEYPAD OR PRESS

SELECT KEY FOB

EMERGENCY KEY
PRESS

THEN

AND SEND SIGNAL FROM SENSOR

SELECT KEY FOB

EQUIPMENT AGE

RF Key Fob Summary Screen

The and arrow buttons step through the key fob numbers.

TO SELECT FROM LIST

OR PRESS SKIP TO JUMP TO Q-4

SELECT KEY FOB

USED

RF KEY FOB REPORTING CODES

RF key fob #1

FOR NEXT OPTION

OR

PRESS insert FOR EACH WORD

ENTER ON KEYPAD OR PRESS
OR

PRESS

The EDIT CURRENT and EDIT NEXT buttons return to key fob
programming.

TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT KEY FOB

ARM NO DELAY

Pressing SKIP goes to question Q-4 (RF keypad programming).

PRESS

OR
TO SELECT FROM LIST

FOR NEXT OPTION

ENTER ON KEYPAD OR PRESS

SELECT KEY FOB

KEY 4 OUTPUT

OR
TO SELECT FROM LIST

PRESS

Figure 53. Key Fob Summary Screen

26

TO FINISH FOR THIS SENSOR, THEN

edit
next

FOR NEXT SENSOR, OR skip FOR Q4

Figure 54. Key Fob Programming Outline

Installer Programming
RF Key Fob Programming Steps

Q-3

Select fob # (1-8)

Up to eight wireless 4-button key fobs can be used with each Control Panel. Key
fobs reports as sensors 51-58. The options for each fob are programmed with
sub-option questions.

Select fob (#) emergency key (0-4)

DEFAULT: Disabled (0)
Pressing the
and
buttons on a key fob at the same time for five
seconds can trigger an emergency alarm.
The default (0) disables the emergency function for this fob.
To enable the emergency function for this fob, select one of the four options:

Begin by entering the fob number or select it using the or arrows.

Program the key fobs by using and arrows to select the sub-options.

FOB EMERGENCY KEY FUNCTION

(0) disabled

NOTE: To skip RF key fob programming, press SKIP to jump from

question Q-3 to question Q-4 (RF keypad programming).

(1) auxiliary alarm

(2) audible alarm

Select fob (#) used (0-1)

DEFAULT: Unused (0)

(3) silent panic

(4) fire

Key fobs can be used with the Control Panel or not.

The default (0) sets all key fobs as unused (0).
To enable programming for this key fob, select used (1).

Select key fob (#) equipment code (0-9999)

DEFAULT: (0000) other
The key fob equipment code defines the sensors manufacturer and type.
The default is (0000) other.
Select (0866) KEY2-345 4-button keyfob remote
for a 2GIG-KEY2 key fob remote.
Select (0577) Existing keyfob remote for an existing key fob remote.
NOTE: Only 2GIG-KEY1-345 or 2GIG-KEY2-345 key
fobs can be used with this system.

Enter key fob (#) other equipment code (0-9999)

DEFAULT: 0
NOTE: This question is only displayed if (0000) other
is selected for a key fobs equipment code.

The equipment code is a 4-digit code that is assigned to the model of key fob
being used.
Enter the equipment code number for the key fob.

Enter fob (#) serial number (7 digits)

DEFAULT: 0000000
Key fob serial numbers can be manually entered or learned from the fob.
For manual entry, enter the fob number that was logged for the fob being
programmed. Use the SHIFT button to access alpha characters.
For automatic entry, press SHIFT, then press LEARN. The Control
Panel will wait for a fob transmission. Trigger the fob being programmed
and the Control Panel will learn the fobs serial number.

Select fob (#) equipment age (0-1)

DEFAULT: New (0)
The Control Panel can be used with new or existing key fobs.
If this fob is new for the installation, leave the default of new (0).
If this fob is already installed, select existing (1).

Select fob (#) key 2 can disarm (0-1)

DEFAULT: Enabled (1)
Key fobs can be set to allow disarming the Control Panel with the fobs
button or not. If using a key fob as a stationary wall fob, it can be set to prevent
someone from using it to disarm the system.
The default (1) allows this fob to disarm the system.
To not allow this fob to disarm the system, select disabled (0).

Construct fob (#) voice descriptor

DEFAULT: Keyfob (#)
The voice descriptor is the words the Control Panel will use for this fob for low
battery announcements and log entries. Up to five words are allowed.
Press INSERT to place a word from the vocabulary into the data entry field.
Use the or arrows to scroll through the words,
or enter the words 3-digit index number.
Press INSERT again for the next word. Up to five words are allowed.
To remove a word, press DELETE.

Select fob (#) arm no delay (0-1)

DEFAULT: Disabled (0)
Key fobs can be set to arm the Control Panel with or without an Entry Delay.
The default (0) sets this fob to arm the system with an Entry Delay.
To set this fob to arm the system without an Entry Delay, select enabled (1).

Select fob (#) key 4 output (0-2)

DEFAULT: Disabled (0)
The key fobs auxiliary
collector output.

button can be used to trigger the Control Panels open

The default (0) disables this fobs auxiliary button.

To use this fobs auxiliary button, select the output function.
FOB KEY 4 OUTPUT
(0) disabled
(1) toggle output
(2) momentary output

27

Installer Programming
RF Keypad Programming
RF Keypad Programming Outline
The Control Panel can be programmed with up to four RF remote
control keypads or wireless touch screen keypads.
Programming RF keypads into the Control Panel involves selecting
the sensor number for a particular device, setting or learning the
keypads serial number, and selecting the other options for the
keypad.
RF keypads #1 - #4 report as system sensors
#59 - #62 for emergency, and low battery reports.
RF KEYPAD REPORTING CODES
RF keypad #1

Reports as sensor #59

RF keypad #2

Reports as sensor #60

RF keypad #3

Reports as sensor #61

RF keypad #4

Reports as sensor #62

KEYPAD PROGRAMMING (Q-4) OUTLINE

STEP DOWN
THROUGH OPTIONS

SELECT OPTION WITH

THESE KEYS

User Codes #1 - #8 are reported for openings and closings.

User Code #0 is reported for Quick Arming.

ENTER ON CONTROL PANEL OR PRESS

Refer to Figure 56 for an outline of the steps required to program

RF remote control keypads into the Control Panel. The options that
can be set for each RF remote control keypad are:

SELECT RF KEYPAD #

PRESS

FOR NEXT OPTION

OR
TO SELECT FROM LIST
OR PRESS SKIP TO JUMP TO Q-5

RF Keypad Number Keypad number 1-4

SELECT RF KEYPAD
USED

RF Keypad Used Keypad used or not

ENTER ON CONTROL PANEL OR PRESS

OR

RF Keypad Equipment Code Sensor model

Q-4 SUB-QUESTIONS

PRESS

RF Keypad Other Equipment Code Enter special

equipment code (only shown for sensors set as other)
RF Keypad Serial # Serial number labeled on
keypad; hand enter or learn by sending signal
RF Keypad Equipment Age New unit or existing keypad
RF Keypad Emergency Keys Enable
or disable keypad emergency keys

SELECT RF KEYPAD
EQUIPMENT CODE

PRESS

PRESS

PRESS

TO SELECT FROM LIST

PRESS

FOR NEXT OPTION

ENTER ON CONTROL PANEL OR PRESS

shift

ENTER ON CONTROL PANEL OR PRESS

OR
TO SELECT FROM LIST
ENTER ON CONTROL PANEL OR PRESS
OR
TO SELECT FROM LIST

FOR NEXT OPTION

CONSTRUCT RF KEYPAD
VOICE DESCRIPTOR

THEN learn OR learn

AND SEND SIGNAL FROM SENSOR

FOR NEXT OPTION

SELECT RF KEYPAD
EMERGENCY KEYS
(ONLY FOR NON-TS1 KEYPADS)
PRESS

ENTER ON CONTROL PANEL

FOR NEXT OPTION

SELECT RF KEYPAD
EQUIPMENT AGE

The and arrow buttons step through the RF keypad numbers.

Pressing SKIP goes to question Q-5 (Control Panel programming).

OR

FOR NEXT OPTION

ENTER RF KEYPAD
SERIAL NUMBER

RF Keypad Summary Screen

The EDIT CURRENT and EDIT NEXT buttons return to RF keypad

programming.

ENTER ON CONTROL PANEL OR PRESS

ENTER RF KEYPAD
OTHER EQUIPMENT CODE
(ONLY FOR "OTHER" EQUIPMENT)

RF Keypad Voice Descriptor Name

assigned to the keypad
After setting all the options for a sensor, the RF keypad summary
screen is displayed. The screen can also be displayed for
programmed RF keypads during RF keypad program editing by
pressing the SUM button.

TO SELECT FROM LIST

FOR NEXT OPTION

PRESS insert FOR EACH WORD

ENTER ON CONTROL PANEL OR PRESS
OR
TO SELECT FROM LIST

PRESS

Figure 55. RF Keypad Summary Screen

28

TO FINISH FOR THIS SENSOR, THEN

edit
next

FOR NEXT SENSOR, OR skip FOR Q5

Figure 56. RF Keypad Programming Outline

Installer Programming
RF Keypad Programming Steps

Q-4

Select RF keypad # (1-4)

Up to four wireless keypads can be used with each Control Panel. The options for
each sensor are programmed with sub-option questions.
Begin by entering the RF keypad number or
select it using the or arrows.
Program the RF keypads by using the and
arrows to select the sub-options.
NOTE: To skip RF keypad programming, press SKIP to jump from
question Q-4 to question Q-5 (Exit Delay programming).

Select RF keypad (#) used (0-1)

DEFAULT: Unused (0)
RF keypads can be used with the Control Panel or not.
The default (0) sets all RF keypads as unused.
To enable programming for this RF keypad, select used (1).

Select RF keypad (#) equipment code (0-9999)

DEFAULT: (0000) other
The RF keypad equipment code defines the sensors manufacturer and type.
The default is (0000) other.
Select (867) PAD1-345 wireless keypad for a 2GIG-PAD1 RF keypad.
Select (1059) TS-1 wireless touchscreen keypad for
a 2GIG-TS1 Wireless Touch Screen Keypad.
NOTE: The TS-1 wireless keypad is not for UL985 installations.

Enter RF keypad (#) other equipment code (0-9999)

DEFAULT: 0
NOTE: This question is only displayed if (0000) other is
selected for an RF keypads equipment code.

The equipment code is a 4-digit code that is assigned to the model of keypad
being used.
Enter the equipment code number for the RF keypad.

Enter RF keypad (#) serial number (7 digits)

DEFAULT: 0000000
or
RF keypad (#) keypad id (read-only)
RF keypad serial numbers for standard keypads can be manually entered or
learned from the RF keypad. Model 2GIG-TS1 wireless touch screen keypads
serial numbers can only be learned from the keypad.
Standard Keypads:
For manual entry, enter the RF keypad number that
was logged for the RF keypad being programmed. Use
the SHIFT button to access alpha characters.
For automatic entry, press SHIFT then press LEARN.
The Control Panel will wait for an RF keypad transmission.
Trigger the RF keypad being programmed, and the Control
Panel will learn the RF keypads serial number.
TS1 Wireless Touch Screen Keypads:
For 2GIG-TS1 Wireless Touch Screen Keypads press LEARN. The Control
Panel will display Pair with TS-1. Initiating learning process. Press the
TS1 keypads PAIR WITH PANEL button. Both the TS1 and the Control
Panel will display The learn operation succeeded when complete.
The Control Panel will display RF keypad (#1-4) for keypad identification.
The TS1 will display Network ID: xxxx which is the unique
serial number identifying the specific keypad.
Press OK on both the Control Panel and TS1 to continue.
NOTE: The Model 2GIG-TS1 wireless touch screen keypad will
display The security system is temporarily not operational after
learning the keypad. This is normal, and will be displayed anytime the
Control Panel is in system configuration (programming) mode.

Select RF keypad (#) equipment age (0-1)

DEFAULT: New (0)
The Control Panel can be used with new or existing RF keypads.
If this RF keypad is new for the installation, leave the default of new (0).
If this RF keypad is already installed, select existing (1).

Select RF keypad (#) emergency keys (0-1)

DEFAULT: Enabled (1)
NOTE: This step is not displayed for Model 2GIG-TS1 keypads.

Standard RF keypads have 24-hour emergency buttons labeled FIRE and

POLICE.
The default (1) enables this RF keypads emergency keys.
To disable this RF keypads emergency keys, select disabled (0),
the keys will not be able to trigger an alarm or report.
NOTE: The RF keypads POLICE button will trigger a silent alarm
if programming question Q-16 is set to silent panic.

TO ENSURE SENDING A SIGNAL, BE SURE TO INSTRUCT THE END USER

TO PRESS THE RF KEYPAD EMERGENCY KEYS UNTIL THE KEYPADS
INDICATOR LIGHTS.

Construct RF keypad (#) voice descriptor

DEFAULT: Keypad (#)
The voice descriptor is the words the Control Panel will announce for this RF
keypad. Up to five words are allowed.
Press INSERT to place a word from the vocabulary into the data entry field.
Use the or arrows to scroll through the words,
or enter the words 3-digit index number.
Press INSERT again for the next word. Up to five words are allowed.
To remove a word, press DELETE.

29

Installer Programming
Control Panel Programming Questions

Q-5

Enter exit delay, in seconds (45-120)

DEFAULT: 60 seconds (Required SIA CP-01 Default)
The Exit Delay can be set from 45 to 120 seconds.
The default (60) sets the Exit Delay to 60 seconds.
To change the Exit Delay, enter a value from (45-120) seconds.
NOTE: This default can be changed without affecting SIA CP-01 compliance.

Q-6

Enter entry delay 1, in seconds (30-240)

DEFAULT: 30 seconds (Required SIA CP-01 Default)

Q-11

Enter CS #1 phone number (0-25 digits)

DEFAULT: No default
The telephone number for Central Station #1 can be up to 25 digits.
Enter the Central Station #1 telephone number.
The SHIFT button accesses the pound and star symbols.
The P button adds a 3-second pause to the dialing.
NOTE: If a second Central Station telephone number is programmed
with question Q-41, the Control Panel will alternate between the
two Central Station telephone numbers. After two failed telephone
dialing attempts, the Control Panel will try to connect using the
GSM radio module if it is installed. If the GSM radio module is not
installed, the Control Panel will make eight dialing attempts.

The Entry Delay #1 can be set from 30 to 240 seconds.

The default (30) sets the Entry Delay #1 to 30 seconds.
To change the Entry Delay #1, enter a value from (30-240) seconds.
NOTE: Per SIA CP-01, the combination of the Abort Window Dialer Delay
(Q-35) and the Entry Delay (Q-6 or Q-7) cannot exceed one minute.

Q-7

Enter entry delay 2, in seconds (30-240)

DEFAULT: 45 seconds (Required SIA CP-01 Default)
The Entry Delay #2 can be set from 30 to 240 seconds.
The default (45) sets the Entry Delay #2 to 45 seconds.
To change the Entry Delay #2, enter a value from (30-240) seconds.
NOTE: Per SIA CP-01, the combination of the Abort Window Dialer Delay
(Q-35) and the Entry Delay (Q-6 or Q-7) cannot exceed one minute.

Q-8

Select dialer (0-1)

DEFAULT: Disabled (0)
The dialer (digital communicator) can be enabled for a monitored system or
disabled for a local alarm or when the GSM module is used exclusively for
reporting.
The default (0) sets the dialer as disabled.
To turn on the dialer, select enabled (1).
NOTE: If the dialer is disabled with this programming question,
telephone line failure detection is also disabled regardless of
the setting of the telephone fail detection question Q-63.

Q-9

Enter dialing prefix (0-4 digits)

DEFAULT: No default
Some telephone PBX systems require a dialing prefix to acquire a dial tone.
If the telephone system that the Control Panel is connected
to requires a dialing prefix, enter up to four digits.
The SHIFT button accesses the pound and star symbols.
The P button adds a 3-second pause to the dialing.

Q-10

Enter call waiting disable code (0-6 digits)

DEFAULT: No default (Required SIA CP-01 Default)
If the subscribers telephone line has call waiting, incoming call tones on the line
could interfere with a communicator report to the Central Station. To prevent this,
the communicator can send the call waiting disable code before making a report.
If call waiting is active on the telephone line,
enter the call waiting disable code.
The SHIFT button accesses the pound and star symbols.
The P button adds a 3-second pause to the dialing.
NOTE: If the first attempt fails, this code will be
ignored on the rest of the attempts.

30

Q-12

Enter CS #1 account number (4 digits)

DEFAULT: No default
The account number for Central Station #1 is always four digits and can include
some alpha characters.
Enter four digits for the Central Station #1 account number.
The SHIFT button accesses B, C, D, E, and F characters.

Q-13

Select 2-way voice (0-2)

DEFAULT: Stay on line (1)
The Control Panel supports 2-way voice communications between the subscriber
and the Central Station operator over the telephone line or the GSM cellular radio
(if installed) after an alarm has been reported.
The default (1) allows 2-way audio over the telephone line or GSM radio.
Selecting (2) allows 2-way audio over the telephone
line or GSM radio during fire and CO alarms.
To turn off the 2-way audio feature, select disabled (0).
When the Control Panel connects with the operator, it will beep once per second
(every six seconds with a GSM connection). The beep alternates between two tones
and indicates the panel is waiting for a session command. If the operator fails to issue
a command within one minute (three minutes with a GSM connection), the call is
terminated. Once the operator presses a command option, the beeps will stop and
a 5-minute audio session will start (3-minute audio session with a GSM connection).
When 2-way voice communications have been established, the Central Station
operator can use the following telephone keys to control the communications.
Each time the operator uses a command key, the session is extended for five
additional minutes (three minutes with a GSM connection). During the last minute
of communications, the system will beep twice every 15 seconds to indicate that
time is running out.
enables Talk Mode one-way communication from
Pressing
the CS to the Premises and allows the operator to talk.
enables VOX Mode two-way
Pressing
communications from the CS to the premises.
Pressing
enables Listen Mode one-way
communication from the premises to the CS.
Pressing
extends the session five minutes
without changing the mode of operation.
causes the audio session to end and terminates the call.
Pressing

Q-14

Select silent panic/burglary listen only

DEFAULT: Enabled (1)
The Control Panel supports audio listen-in of the subscriber premises from the
Central Station over the telephone line after a silent panic (police emergency),
silent burglary, or duress alarm has been reported.
The default (1) enables audio listen-in after a silent
panic, silent burglary, or duress alarm.
This option is permanently set and cannot be disabled.

Installer Programming

Q-15

Q-21

Select dialing type (0-1)

DEFAULT: Touch tone (0)

Select siren supervision time (0-3)

DEFAULT: Disabled (0)

The digital communicator can dial using tones or pulse.

The wiring connection to the external sounder can be supervised. If the wiring to
the sounder is cut for 15, 30, or 45 seconds, a bell trouble report can be sent to
the Central Station.

The default (0) is for touch tone (DTMF) dialing.

For rotary dialing, select pulse (1).

Q-16

Select police emergency key (0-2)

DEFAULT: Audible (1)
The Control Panels panic emergency button action can be programmed. The panic
emergency button is displayed by pressing the Control Panels
button.
The default (1) allows the panic emergency
button to sound an audible alarm.
For silent activation, select silent panic (2).
To disable and not display the panic emergency button, select disabled (0).
NOTE: Setting this programming question for silent panic (2)
will make the POLICE button on all RF keypads silent also.

Q-17

The default (0) disables external sounder supervision.

To supervise the external sounder wiring, select (1) for
15 seconds; (2) for 30 seconds; or (3) for 45 seconds.

Q-22

Enter CS lack of usage notification time (0-255)

DEFAULT: Seven days (7)
Inactivity reports can be sent to the Central Station if the system has not been
armed for a period of days.
The default (7) sets the lack of usage feature at seven days.
To change the lack of usage feature duration, select (1-255) days.
To turn off the lack of usage feature, select disabled (0).

Q-23

Select fire emergency key (0-1)

DEFAULT: Audible (1)

Enter radio modem network failure time (0-255)

DEFAULT: 30 minutes

The Control Panels fire emergency button can be enabled or disabled. The fire
emergency button is displayed by pressing the Control Panels
button.

NOTE: GSM Module must be installed to use this function.

The default (1) allows the fire emergency button to sound an audible alarm.
To disable and not display the fire emergency button, select disabled (0).

Q-18

Select emergency key (0-1)

DEFAULT: Audible (1)
The Control Panels emergency button can be enabled or disabled. The panels
emergency button is displayed by pressing the Control Panels
button.
The default (1) allows the emergency button to sound an audible alarm.
To disable and not display emergency button, select disabled (0).
NOTE: If all three emergency buttons are disabled, pressing the Control Panels
button will display a message that the emergency buttons are disabled.

Q-19

Select quick arming (0-1)

DEFAULT: Enabled (1)
Quick arming allows the subscriber to arm the system without having to enter
their User Code. (Quick arming reports as User 0 if open/close reports are sent.)
The default (1) allows quick arming.
To turn off quick arming, select disabled (0).

Q-20

Select swinger shutdown count (1-6)

DEFAULT: Two trips (2) (Required SIA CP-01 Default)
An unwanted series of multiple faults (usually caused by a bad contact or sensor)
is called a swinger. Swinger shutdown sets the maximum number of alarms that
any sensor or hardwire loop can trigger during a single arming period.
NOTE: CO and smoke detector alarms are not limited
by the swinger shutdown count. Other types of 24-hour
zones are limited by the swinger shutdown count.

The default (2) sets the swinger shutdown count at two trips.
To change the swinger shutdown count, select (1-6).
NOTE: This default can be changed without affecting SIA CP-01 compliance.

Sets the amount of time required for triggering a trouble condition if the system
detects that the optional GSM radio modem has lost its cellular connection. (After
cellular service has been restored for five minutes, the trouble condition will clear.)
The default (30) sets the failure detection time at 30 minutes.
To disable radio modem failure detection, select disabled (0).
To choose a different failure detection time, select (1-255) minutes.

Q-24

Select radio modem network failure causes trouble (0-1)

DEFAULT: Enabled (1)
NOTE: GSM Module must be installed to use this function.

Selects whether the control panel will sound and display trouble if the optional
GSM radio modem has lost its cellular connection. The trouble sounder can be
silenced by the user at the Control Panel (GSM trouble is logged regardless of
this setting). When the GSM radio modem connection is restored, the trouble
indications will automatically clear.
The default (1) allows radio modem failure trouble indications.
To turn off radio modem failure trouble indications, select disabled (0).

Q-25

Select radio modem network failure reports (0-1)

DEFAULT: Enabled (1)
NOTE: GSM Module must be installed to use this function.

If the optional GSM radio modem loses its cellular connection, the Control Panel
can report the fault and restore via land-line if telephone reporting is enabled.
The default (1) allows radio modem failure/restore reporting.
To turn off radio modem failure/restore reporting, select disabled (0).

Q-26

Select auto stay (0-1)

DEFAULT: Enabled (1) (Required SIA CP-01 Default)
When auto stay is enabled and the system is armed in the Away Mode, if an exit/
entry sensor is not violated during the Exit Delay, the system will arm in the Stay
Mode.
The default (1) enables the auto stay feature.
To turn off the auto stay feature, select disabled (0).
NOTE: The auto stay feature will not switch the system to Stay
Mode if the system is armed to Away Mode using a key fob
remote or remotely armed via telephone or computer.

31

Installer Programming

Q-27

Q-33

Select exit delay restart (0-1)

DEFAULT: Enabled (1) (Required SIA CP-01 Default)

Select cross sensor 47-48 (0-1)

DEFAULT: Disabled (0)

When Exit Delay restart is enabled, re-entering the premises through an exit/
entry door during the Exit Delay will restart the Exit Delay. The restart of the Exit
Delay will only occur one time; further violations of an exit/entry sensor will not
extend the Exit Delay.

The Control Panel can be programmed so sensors 47 and 48 must both be

violated during a set time to trigger an alarm. This is called cross sensor
verification. When enabled, if only one sensor (47 or 48) is violated, the alarm will
not trigger, but a trouble report will be sent for the sensor that triggered.

The default (1) enables the Exit Delay restart feature.

To turn off the Exit Delay restart feature, select disabled (0).

NOTE: CO and fire zone cannot be used for cross sensors.

The default (0) disables the cross sensor feature.

To use the cross sensor feature, select enabled (1).

Q-28

Select quick exit (0-1)

DEFAULT: Enabled (1)

NOTE: See Q-34 for information on setting the cross sensor timeout.

The quick exit feature allows the user to start the Exit Delay while the system is
armed. When this feature is enabled, a QUICK EXIT button will appear on the
Security Screen. Pressing QUICK EXIT while the system is armed allows the
user to leave through an exit/entry door. After the Exit Delay expires, the system
will return to being armed in the mode it was in before (either Stay or Away Mode).

Enter cross sensor timeout, in seconds (10-120)

DEFAULT: 10 seconds

The default (1) enables the quick exit feature.

To turn off the quick exit feature, select disabled (0).

Q-29

Enter periodic test, in days (0-255)

DEFAULT: 30 days
Automatic test reports can be sent to the Central Station every certain number of days.
The default (30) sends an automatic test report every 30 days.
To set a different period for automatic test reports, select (1-255) days.
To disable automatic test reports, select (0).

Q-31

Enter cancel time, in minutes (5-255)

DEFAULT: 5 minutes (Required SIA CP-01 Minimum)
A cancel report will be sent to the Central Station after an alarm, if the system is
disarmed within the programmed time.
The default (5) sets the cancel time at five minutes.
For a longer cancel time, select (6-254) minutes.
To have the Control Panel always send a cancel report when
the system is disarmed after an alarm, select (255).
NOTE: See Q-32 for information on displaying when a cancel report is sent.
NOTE: This default can be changed without affecting SIA CP-01 compliance.

Q-32

Select cancel display (0-1)

DEFAULT: Enabled (1) (Required SIA CP-01 Default)
A cancel report will be sent to the Central Station after an alarm, if the system is
disarmed within the programmed time. The Control Panel can also show on the
display that a cancel report was sent.
The default (1) enables the cancel display feature.
To turn off the cancel display feature, select disabled (0).

Q-34

The cross sensor timeout is the maximum period of time allowed between
violation of sensors 47 and 48 that will trigger an alarm. If both sensors are
violated within this time period, an alarm will be triggered. If both sensors are not
violated within this time period, an alarm will not be triggered.
NOTE: Cross sensor verification must be enabled
with Q-33 for this feature to function.

The default (10) sets the cross sensor timeout at 10 seconds.

To change the cross sensor timeout duration, select (11-120) seconds.

Q-35

Select abort window dialer delay (0-2)

DEFAULT: 30 seconds (1) (Required SIA CP-01 Default)
The Control Panels dialer (digital communicator) delays calling the Central
Station to allow the user enough time to cancel a false alarm before it is reported.
The default (1) sets the dialer delay at 30 seconds.
To change the dialer delay, select (0) for 15 seconds or (2) for 45 seconds.
NOTE: Per SIA CP-01, the combination of the Abort Window Dialer Delay
(Q-35) and the Entry Delay (Q-6 or Q-7) cannot exceed one minute.
NOTE: The dialer delay can be disabled per sensor without
affecting SIA CP-01 compliance. See sensor programming.

Q-36

Select burglary bell cutoff (0-4)

DEFAULT: 4 minutes (0)
When a burglary alarm is triggered, the bell will sound until the burglary bell cutoff
time expires.
The default (0) sets the burglary bell cutoff time to 4 minutes.
To change the burglary bell cutoff time, select (1), (2), (3), or (4):
BURGLARY BELL CUTOFF TIME
(0) 4 minutes
(1) 8 minutes
(2) 12 minutes

NOTE: See Q-31 for information on setting the cancel report trigger time.

(3) 16 minutes

NOTE: This default can be changed without affecting SIA CP-01 compliance.

(4) Unlimited time

NOTE: The 24-hour Auxiliary Alarm Zone (08) does not follow the burglary bell
cutoff time and will sound the Control Panels local alarm until a User Code is
entered. The Auxiliary Alarm Zone does not trigger the external siren (if used).

32

Installer Programming

Q-37

Q-42

Select fire bell cutoff (0-4)

DEFAULT: 4 minutes (0)

Select remote control phone (0-3)

DEFAULT: Data and voice (3)

When a fire alarm is triggered, the bell will sound until the fire bell cutoff time
expires.

This setting controls remote telephone access to the system.

The default (0) sets the fire bell cutoff time to 4 minutes.
To change the fire bell cutoff time, select (1), (2), (3), or (4):
FIRE BELL CUTOFF TIME
(0) 4 minutes
(1) 8 minutes
(2) 12 minutes
(3) 16 minutes
(4) Unlimited time

Q-38

Enter time to detect AC loss, in minutes (0-30)

DEFAULT: 10 minutes (10)
AC power loss will cause an AC power loss alert
to be displayed, and the
length of time before its displayed can be set. When power returns, the time
required before the AC power loss alert
automatically clears is fixed at
one minute.
The default (10) sets the AC power loss alert display time to ten minutes.
To change the AC power loss alert display time, enter (0-30) minutes.
NOTE: After the AC power alert
is displayed or clears, the
AC power loss report or AC power restore report can be sent to the
Central Station immediately, or at a random time, see Q-39.

The data option is for the installer. It allows access for programming and operating
the system with custom PC downloader software.
The voice option is for the subscriber. It allows the subscriber to call the system
from an off-site phone, to get the status of the system, and to perform remote
commands. These commands are executed by entering touch tones. The status
is reported back via voice prompts. A valid User Code is required for remote
telephone access. The user will be able to perform the following functions: arm
in any mode, disarm, bypass, get system status, and turn on or turn off the open
collector output.
If voice access is enabled, to connect to the panel, the subscriber will need to call
the telephone number that the Control Panel is connected to, wait for one or two
rings, then hang up. The subscriber needs to call again, within 10-45 seconds,
and the Control Panel will answer the call.
When the panel answers the phone, the user will be prompted to enter their code.
If a valid code is entered, the system will announce the current system status. If
an invalid code is entered, the panel will ask for the code again. After two invalid
attempts, the panel will disconnect. After two calls, with two invalid attempts each,
the panel will lock out. The lock out will last for 30 minutes.
The default (3) enables data and voice access.
For data only (PC downloader) access, select (1).
For voice access only, select (2).
To disable remote access, select (0).
REMOTE CONTROL PHONE MODE

NOTE: The Control Panels AC power icon displays the power status
immediately. A red X over the icon indicates no AC power.

(0) disabled (no remote control phone)

(1) data only

Q-39

Select random AC loss report time (0-1)

DEFAULT: Enabled (1)

(2) voice only

(3) data and voice

This feature allows the system to report AC power loss and AC power restore at
a random time of up to 45 minutes after the event occurs. This helps to reduce
Central Station congestion due to a wide-spread power outage affecting many
Control Panels at once. The random AC power status report timer is triggered
based on the time set by Q-38.

TELEPHONE KEY

The default (1) allows random timed AC power reports.

To turn off random timed AC power reports, select disabled (0).

Q-40

Enter CS #2 phone number (0-25 digits)

DEFAULT: No default
The telephone number for Central Station #2 can be up to 25 digits. Central
Station telephone #2 is dialed as backup in case telephone #1 does not connect.
Enter the Central Station #2 telephone number.
The SHIFT button accesses the pound and star symbols.
The P button adds a 3-second pause to the dialing.

Q-41

Enter CS #2 account number (4 digits)

DEFAULT: No default
The account number for Central Station #2 is always four digits and can include
some alpha characters.
Enter four digits for the Central Station #2 account number.
The SHIFT button accesses B, C, D, E, and F characters.

REMOTE CONTROL COMMAND

System status report

Arm the system in Away Mode

Arm the system in Stay Mode

Disarm the system

Turn on the auxiliary output

Turn off the auxiliary output

Stop the system status report

Disconnect (hang up)

Repeat command menu

Bypass all open sensors and arm system

NOTE: Remotely arming the system to Away Mode will not start
an Exit Delay or activate Auto Stay Mode (if enabled).

Q-43

Enter installer code (4 digits)

DEFAULT: 1561
The Installer Code is the code required to enter the Installer Toolbox.
The default for the Installer Code is 1561.
To change the Installer Code, enter a new 4-digit code.
BE SURE TO WRITE DOWN THE NEW CODE !!!
NOTE: The Installer Code must be unique from any User Codes.

33

Installer Programming

Q-44

Q-47

Select lock installer programming (0-2)

DEFAULT: Disabled (0)

Select trouble resound after holdoff (0-7)

DEFAULT: Disabled (0)

The installer programming lockout feature is provided to prevent takeovers. The

Control Panel can be set to limit an installers access to programming questions
after a period of 48 hours. The 48 hour lockout timer starts when the installer exits
system configuration mode.

Fire and CO sensors are required to re-sound trouble beeps every four hours
until the trouble is resolved, even if the trouble is acknowledged at the Control
Panel. The Control Panel can be set to delay re-sounding these types of trouble
beeps for 1-7 days.

Three options are available: unlimited full access to programming (no lockout),
limited access to programming after 48 hours, or no access to programming after
48 hours.

NOTE: This feature is not allowed in UL 985 installations. The

setting must be disabled (0) in this grade of installation.

The default (0) selects unlimited full access to programming (no lockout).
To deny access to programming after 48 hours,
select no access to programming (1).
To select limited access to programming after 48 hours, select (2). After the
system has run for 48 hours, installer will be able to view, but not change,
the Central Station phone number, Central Station account number,
lock installer programming, download ID, and default lockout fields.
After the 48 hour lockout timer has locked out the system, the timer can be reset
through the GSM radio or PC downloader by remotely setting this question Q-44
to (0) or (2). Setting the option to (0) or (2) will restart the 48 hour lockout timer.

Q-45

Select lock default programming (0-2)

DEFAULT: Default all (0)
The Control Panel may be able to be hard reset (or soft reset from the Installer
Toolbox) to its factory default values depending on the value entered for this
programming question.
The Control Panel is hard reset by pressing and holding the
buttons while applying power to the Control Panel.

and

The default lockout feature is provided to prevent takeovers. Three options are
available: allow default of all options, allow default of some but not all options, not
allow default of any options.

The default (0) allows trouble beeps for CO and fire sensors
to re-sound every four hours after being acknowledged.
To delay re-sounding trouble beeps for CO
and fire sensors, select (1-7) days.

Q-48

Enter download csid (6 digits)

DEFAULT: 000000
The system supports a 6-digit CSID code that is used for remote telephone
programming of the Control Panel. This code is verified when the Control Panel
connects with the downloading software. If the CSID code doesnt match the
downloading software, the Control Panel will deny the connection.
The CSID code can be entered manually with this programming question.
If this field is left with the default (000000), the first time
the downloading software connects with the Control Panel,
the field will be filled with the softwares CSID.

Q-49

Select programming mode entry reports to CS (0-1)

DEFAULT: Disabled (0)
A report can be sent to the Central Station any time installer programming mode
is entered and exited.
The default (0) prevents reporting programming mode entry and exit.
To report programming mode entry and exit, select enabled (1).

The default setting of default all (0) allows resetting the Control Panel to all
its factory defaults.

NOTE: This report can only be sent through the telephone

dialer. It is not supported through the GSM radio.

To allow resetting the Control Panel to all its factory defaults except the
Central Station phone number, Central Station account number, lock installer
programming, download ID, and default lockout fields, select (1).

Q-50

To deny hard and soft resetting of the Control Panel, select default none (2).
If option (1) or (2) is selected, the option will take effect after the system has run
for 48 hours. This allows the installer to go back and make changes if required.

Select trouble reports to CS (0-1)

DEFAULT: Enabled (1)
Trouble reports can be sent to the Central Station when any sensor trouble
condition occurs.
The default (1) allows reporting sensor trouble conditions.
To not report sensor trouble conditions, select disabled (0).

Q-46

NOTE: This setting does not affect trouble reports caused by Control
Panel conditions, only trouble reports caused by sensors.

The Control Panel will sound trouble beeps caused by AC loss, system low
battery, sensor low battery or RF supervision, failure to communicate, Control
Panel tamper while disarmed, and GSM radio faults.

Select manual bypass reports to CS (0-1)

DEFAULT: Disabled (0)

Select trouble doesnt sound at night (0-1)

DEFAULT: Enabled (1)

To prevent annoying the subscriber, the system can be set to suppress trouble
beeps from sounding from 10 pm to 9 am. The trouble(s) will still be displayed and
immediately reported to the Central Station, and can be acknowledged, but they
wont sound beeps until after 9 am.
If the trouble condition(s) self-clear or are acknowledged before 9 am, no trouble
beeps will sound after 9 am (the conditions will still be recorded in the event
log).
The default (1) suppresses trouble beeps from 10 pm to 9 am.
To allow trouble beeps at any time, select disabled (0).
NOTE: For UL985 Installations, this feature must be disabled.

34

Q-51

Manual bypass reports can be sent to the Central Station when any sensor has
been manually bypassed by the user.
The default (0) prevents sending manual bypass reports.
To allow sending manual bypass reports, select enabled (1).

Installer Programming

Q-52

Q-58

Select AC loss reports to CS (0-1)

DEFAULT: Enabled (1)

Select trouble restore reports to CS (0-1)

DEFAULT: Enabled (1)

AC power loss reports can be sent to the Central Station if the Control Panel
loses AC power.

Trouble restore reports can be sent to the Central Station when any sensor
trouble condition clears.

The default (1) allows AC power loss reports.

To turn off AC power loss reports, select disabled (0).
NOTE: The AC power will have to be absent from the Control Panel for the
time set by programming question Q-38 before the AC power loss trouble
alert
is displayed (the default is 10 minutes). If programming question
Q-39 is enabled, the actual AC power loss report will occur at a random time
is displayed.
of up to four hours after the AC power loss trouble alert
NOTE: The Control Panels AC power icon displays the power status
immediately. A red X over the icon indicates no AC power.

Q-53

Select system low battery reports to CS (0-1)

DEFAULT: Enabled (1)
Low battery reports can be sent to the Central Station if the Control Panels
battery tests low.
The default (1) allows Control Panel low battery reports.
To turn off Control Panel low battery reports, select disabled (0).

Q-54

Select RF low battery reports to CS (0-1)

DEFAULT: Enabled (1)
Sensor low battery reports can be sent to the Central Station if a sensor battery
tests low and sends a low battery transmission to the Control Panel.
The default (1) allows sensor low battery reports.
To turn off sensor low battery reports, select disabled (0).

Q-55

The default (1) allows trouble restore reports.

To turn off trouble restore reports, select disabled (0).

Q-59

Select bypass restores reports to CS (0-1)

DEFAULT: Disabled (0)
Bypass restore reports can be sent to the Central Station when any sensor that
was force bypassed or manually bypassed gets restored.
The default (0) prevents bypass restore reports.
To allow bypass restore reports, select enabled (1).

Q-60

Select AC restore reports to CS (0-1)

DEFAULT: Enabled (1)
AC power restore reports can be sent to the Central Station when the Control
Panel regains AC power after an AC power loss.
The default (1) allows AC power restore reports.
To turn off AC power restore reports, select disabled (0).
NOTE: The AC power will have to be restored to the Control
Panel for one minute before the AC power loss trouble alert
automatically clears. If programming question Q-39 is enabled, the
actual AC power restore report will occur at a random time of up to
four hours after the AC power loss trouble alert
has cleared.
NOTE: The Control Panels AC power icon displays the power status
immediately. A red X over the icon indicates no AC power.

Q-61

Select opening reports to CS (0-1)

DEFAULT: Disabled (0)

Select system low battery restore reports to CS (0-1)

DEFAULT: Enabled (1)

Opening reports can be sent to the Central Station each time the system is
disarmed. The user or key fob number is indicated in the opening report.

Control Panel low battery restore reports can be sent to the Central Station if the
Control Panel battery had tested low and is now OK.

The default (0) prevents opening reports.

To allow opening reports, select enabled (1).

Q-56

The default (1) allows Control Panel low battery restore reports.
To turn off Control Panel low battery restore reports, select disabled (0).

Q-62

Select closing reports to CS (0-1)

DEFAULT: Disabled (0)

Select RF low battery restores reports to CS (0-1)

DEFAULT: Enabled (1)

Closing reports can be sent to the Central Station each time the system is armed.
The user or key fob number is indicated in the closing report. If Quick Arming is
enabled, User #0 is indicated for the closing report.

Sensor low battery restore reports can be sent to the Central Station if a sensor
battery had tested low and is now OK.

The default (0) prevents closing reports.

To allow closing reports, select enabled (1).

The default (1) allows sensor low battery restore reports.

To turn off sensor low battery restore reports, select disabled (0).

Q-63

Q-57

Select phone fail detect (0-1)

DEFAULT: Disabled (0)

Alarm restore reports can be sent to the Central Station after an alarm when
either the bell timeout has been reached or the system is disarmed.

The system can monitor the telephone line connected to the Control Panel. If
the telephone line is shorted or cut, the Control Panel will indicate telephone line
trouble by sounding trouble beeps and displaying the no-phone icon.

Select alarm restore reports to CS (0-1)

DEFAULT: Disabled (0)
If alarm restores are enabled and swinger shutdown is set to two, a restore will
be reported if the sensor is closed (normal state) at bell cutoff or becomes closed
after bell cutoff. If swinger shutdown is set to one, a restore will only be sent if
the sensor is closed at the time of disarm. Restores are not sent if a sensor is in
swinger shutdown until the time of disarm and the sensor is closed.
The default (0) prevents alarm restore reports.
To allow alarm restore reports, select enabled (1).

If the optional GSM radio modem is installed, the telephone line failure will still be
reported if this question is enabled.
The default (0) disables this feature.
To turn on this feature, select enabled (1).
NOTE: If the dialer is disabled with programming question Q-8,
telephone line failure detection is also disabled regardless
of the setting of this programming question.

35

Installer Programming

Q-64

Q-71

Select smart test reports

DEFAULT: Disabled (0)

Select system tamper causes trouble (0-1)

DEFAULT: Enabled (1)

Smart test reports are a way to reduce Central Station traffic. If smart test reports
are enabled and regular periodic test reports are enabled, any non-test report to
the Central Station (alarm, restore, trouble, etc.) during the normal operation of
the system will reset the periodic test report timer. Periodic test reports would only
be sent if the Control Panel has not reported in any way to the Central Station.

The Control Panels case has a tamper switch that detects if the case has been
opened. The system can be programmed so that a tamper switch activation will
cause a trouble indication if the system is disarmed, and an alarm if the system
is armed.

The default (0) prevents smart test reports.

To allow smart test reports, select enabled (1).

Q-65

Select RF jam causes trouble (0-1)

DEFAULT: Disabled (0)
The system can monitor the Control Panels sensor receiver and detect whether a
transmitter is stuck on the air causing jamming. When jam detect is enabled, the
Control Panel will indicate a trouble condition if RF jamming is detected.
NOTE: This programming question only functions if trouble
reports are enabled with programming question Q-50.

The default (0) disables RF jam detection.

To turn on RF jam detection, select enabled (1).

Q-66

The default (1) allows the Control Panel tamper switch to trigger trouble
when the system is disarmed, and alarm when the system is armed.
To have the system ignore the Control Panel
tamper switch, select disabled (0).

Q-72

Select quick bypass (0-1)

DEFAULT: Disabled (0)
Normally, sensors that are violated (open) at the time the system is armed will
require the user to enter their code to force bypass them. The Control Panel can
be programmed so that when the system is armed with open sensors, a code is
not required to bypass the open sensor(s) and complete the arming.
The default (0) requires entering a code to bypass sensors.
To allow bypassing sensors without a code, select enabled (1).

Q-73

Select daylight saving (0-1)

DEFAULT: Enabled (1)

Select disarming keyfob after alarm (alert) (0-1)

DEFAULT: Disabled (0)

The Control Panel can adjust its displayed clock and internal clock for daylight
saving time. If the GSM radio is used, the time will be automatically adjusted
regardless of this setting. The system default is set for post 2007 daylight
saving changeover dates. These dates can be modified in case the daylight
saving changeover date moves again.

The system can produce a unique sound when its disarmed with a key fob after
an alarm has occurred. Four beeps will sound from the Control Panels speaker,
four chirps will sound from the external sounder (if installed). This feature serves
as a safety alert to the user so they can enter the protected premises with caution.

The default (1) enables daylight saving time adjustment.

To turn off automatic daylight savings adjust, select disabled (0).
NOTE: If required, use programming questions Q-67, Q-68, Q-69,
and Q-70 to modify the daylight saving start and stop dates.

Q-67

Select daylight saving start month (01-12)

DEFAULT: March (03)
The default (03) sets March as the daylight saving start month.
To change the start month, enter the month, January - December
(01-12), that the new daylight saving time will start.

Q-68

Select daylight saving start Sunday (1-7)

DEFAULT: 2nd Sunday (2)
The default (2) sets the second Sunday as the daylight saving start week.
To change the start week, enter the 1st, 2nd, 3rd, 4th, last, second
from last, third from last (1-7) as the daylight saving start week.

Q-69

Select daylight saving end month (01-12)

DEFAULT: November (11)
The default (11) sets November as the daylight saving end month.
To change the end month, enter the month, January - December
(01-12), that the custom daylight saving time will end.

Q-70

Select daylight saving end Sunday (1-7)

DEFAULT: 1st Sunday (1)
The default (1) sets the first Sunday as the daylight saving end week.
To change the end week, enter the 1st, 2nd, 3rd, 4th, last, second
from last, third from last (1-7) as the daylight saving end week.

36

The default (0) will not cause a unique sound

when disarming after an alarm.
To cause unique sound when disarming after an alarm, select enabled (1).

Q-74

Select keyfob arm / disarm confirmation (0-1)

DEFAULT: Disabled (0)
The system can produce a unique sound when its armed or disarmed with a
key fob. The Control Panels speaker will sound one beep when arming and two
beeps when disarming. The external sounder (if installed) will sound one chirp
when arming and two chirps when disarming (four beeps after an alarm if Q-73 is
enabled). This feature indicates to the user that their key fob signal was received
by the Control Panel in case other arm/disarm indications (armed LED, etc.) are
not available or visible to the user.
The default (0) will not cause a unique sound when controlled by a key fob.
To cause a unique sound when controlled by a key fob, select enabled (1).

Q-75

Select auto unbypass for manual bypass (0-1)

DEFAULT: Enabled (1)
Violated (open) sensors can be manually bypassed by the user through the User
Toolbox or force bypassed at the time of arming.
Force bypassed sensors automatically have their
bypasses removed when the system is disarmed.
Manually bypassed sensors can have their bypass automatically
removed at disarming or have their bypasses remain in place.
The default (1) automatically removes bypasses from manually
bypassed sensors when the system is disarmed.
To have manually bypassed sensors remain bypassed
when the system is disarmed, select disabled (0).

Installer Programming

Q-76

Q-79

Select force bypass reports (0-1)

DEFAULT: Disabled (0)

Select Z-Wave feature (0-3)

DEFAULT: Disabled but visible (1)

The system can report which sensors have been force bypassed by the user
when the system is armed. Forced bypassed sensors are always recorded in the
event log, regardless of the setting of this programming question.

The Z-Wave home services feature can be enabled or disabled with various
remote control access options.

The default (0) prevents reporting forced bypassed sensors.

To report forced bypassed sensors, select enabled (1).

Q-77

Select event log (0-3)

DEFAULT: All events (3)
To control the amount of event log entries, the events that get recorded into the
systems event log can be selected by type. This setting filters the events that
populate the event log.
The default (3) records all events in the event log.
For different event log filtering options, select (0), (1), or (2):
EVENT LOG FILTERS
(0) disabled (no events logged)
(1) all events except open, closing, and bypass

The default (1) displays the SERVICES button, but will show a message
that the feature is currently disabled and the user should call the installer.
To hide the SERVICES button, select disabled and hidden (0).
To show the SERVICES button and disable offsite remote control, select (2).
To show the SERVICES button, with Z-Wave rules disabled
and off-site remote control enabled, select (3).

Q-80

Select Z-Wave switches feature (0-1)

DEFAULT: Disabled (0)
Display of the Home Services SWITCHES button can be enabled or disabled.
NOTE: This programming question only functions if the
Z-Wave feature enable question Q-79 is set to (2) or (3).

The default (0) hides the SWITCHES button.

To display the SWITCHES button, select enabled (1).

(2) all events except open and closing

(3) all events

Q-78

Select output (00-10)

DEFAULT: Follows internal sounder alarm (11)
(Required SIA CP-01 Default)
The systems open collector output is available on the Control Panels terminal
block to connect to an external device. The conditions that will cause the open
collector output to activate are programmable.
Select one activation option for the Control Panels open collector output:
OPEN COLLECTOR OUTPUT MODE

Q-81

Select Z-Wave thermostats feature (0-1)

DEFAULT: Disabled (0)
Display of the Home Services THERMOSTATS button can be enabled or
disabled.
NOTE: This programming question only functions if the
Z-Wave feature enable question Q-79 is set to (2) or (3).

The default (0) hides the THERMOSTATS button.

To display the THERMOSTATS button, select enabled (1).

Q-82

Select Z-Wave door locks feature (0-1)

DEFAULT: Disabled (0)

(00) disabled

Display of the Home Services DOOR LOCKS button can be enabled or disabled.

(01) activated when armed

NOTE: This programming question only functions if the

Z-Wave feature enable question Q-79 is set to (2) or (3).

(02) activated when disarmed

(03) activated on FTC (failure to communicate)
(04) activated on siren supervision
(05) activated on radio fault
(06) activated on burglary alarm
(07) activated on fire alarm
(08) activated on any alarm
(09) activated on any system trouble
(10) Z-wave activation (Option #10 not currently active)
(11) follows internal sounder alarm
(12) follows exit/entry beeps

The default (0) hides the DOOR LOCKS button.

To display the DOOR LOCKS button, select enabled (1).

Q-83

Select temperature display units (0-1)

DEFAULT: Degrees Fahrenheit (0)
The Home Services Z-Wave thermostat display screens can show the
temperature in degrees Fahrenheit or degrees Celsius.
NOTE: This programming question only functions if the
Z-Wave feature enable question Q-79 is set to (2) or (3)
and the thermostat feature is enabled with Q-81.

The default (0) displays temperature in degrees Fahrenheit.

To display temperature in degrees Celsius, select (1).

37

Installer Programming

Q-84

Q-88

Select services require master code (0-1)

DEFAULT: Disabled (0)

Select siren mode (0-1)

DEFAULT: Sound for burglary and fire/CO (0)

The SERVICES button can be configured to require the use of the Master User
Code to access Services.

This setting selects which alarm types will activate a Z-Wave siren linked to the
system.

The default (0) disables the requirement for the Master

User Code to access the SERVICES menu.
To require the use of the Master User Code to access
the SERVICES menu, select enabled (1).
When enabled then the Master User Code is required to access the Services and
the Z-wave device configurations. This keeps unauthorized users from being able
to change Z-wave settings, such as temperature, lights and locks.

Q-85

Select master user access to zwave toolbox (0-1)

DEFAULT: Disabled (0)
The Z-Wave Toolbox menu can be set to require the use of the Master User Code
or the Installer Code. By default, the Installer Code is required for users to access
the Z-Wave Toolbox.
The default (0) requires the use of the Installer Code to access the Z-Wave
Toolbox menu and all of its features, including the Advanced Toolbox.
To require the use of the Master User Code or the Installer Code
to access the Z-Wave Toolbox menu, select enabled (1).
NOTE: When enabled (1) the Installer code will still be required
to access the Advanced Toolbox menu. This prevents end
users from adding or removing Z-Wave devices.

Q-86

Select disable siren after two-way audio (0-1)

DEFAULT: Disabled (0)
This setting enhances system operation in personal emergency applications and
also provides the dealer with the option of the siren sounding until the bell cut off
or to the end of a two-way-voice session.
The default (0) will cause the siren to resume after two-way
audio (if the bell cut off timer has not expired).
Enable (1) will cause the siren to shut off after a two-way audio session.

Q-87

Select keyfob/remote arming mode

on system not ready (0-2)
DEFAULT: Auto bypass with zone participation on restore (0)
This setting controls how the system will react when there are open sensors and
the system is armed remotely.
The default (0) will automatically bypass all sensors that
are open when the system is armed remotely. If a sensor
restores while the system is armed, the sensors bypass will be
removed, and the sensor will be ready to trigger an alarm.
To automatically bypass all sensors that are open when the system
is armed remotely, and keep all bypasses in place during the
arming cycle, even if a sensor restores, select auto-bypass (1).
To prevent arming remotely when any sensor is
open, select arm only when ready (2).

38

The default (0) will cause a Z-Wave siren to sound

during burglary and fire/CO alarms.
To have a Z-Wave siren sound only during burglary
alarms, select sound for burglary only (1).

Final Installation Setup

Exiting Programming
After programming the Control Panel, all the changes need to
be saved in memory. After saving, the programmed settings will
remain in memory, even after a total power loss.

6. Press BRIGHTNESS / VOLUME. Set the level for the display

brightness. Set the chime & voice volume. Press OK when finished.

1. After setting all the required programming values for

the sensors and the Control Panel, press END.
2. Review the Control Panel Summary screen. Use the and arrows
to scroll through the listing. Verify that each option is set correctly.
3. To save the programming changes, be sure the SAVE CHANGES
option is checked. To exit without saving programming changes
un-check the SAVE CHANGES option (for verification, an additional
confirmation screen will display). Press EXIT. The Control Panel
will take a few seconds to restart and display the Home Screen.

Figure 57. Programming Summary Screen

Customizing the Installation

After programming the Control Panel, go to the User Toolbox and
customize the system to suit the installation.

Figure 60. Brightness / Volume Screen

7. Press to view the second User Toolbox screen.

Figure 61. User Toolbox Screen 2 of 3

8. Press BACKLIGHT TIMEOUT and set the display lighting
timeout. Choose the length of time that the display will
remain lit after it is idle. Press OK when finished.

1. After the Control Panel restarts, press SECURITY, MENU, TOOLBOX to

access the User Toolbox. Enter the Master User Code (default = 1111).

Figure 62. Backlight Timeout Screen

Figure 58. User Toolbox Screen 1 of 3
2. Press USER MANAGEMENT.
3. Setup the User Codes. Press a User button to add, change,
or delete a User Code. The system will ask to confirm the
code entered. Be sure to set a Duress Code as User #8.
NOTE: User codes 0000, 0001, and the code used
for the Installer Code are not permitted.

9. Press SET DATE and SET TIME to set the calendar and clock. On
the Set Date screen, use the and arrows to set the month, day,
and year. On the Set Time screen, use the and arrows to set the
hours, minutes, and AM/PM. Press OK when finished. A confirmation
screen will show. Verify the time and date, then Press OK.
NOTE: If the GSM radio module is installed and registered, the
date and time will be set automatically.

4. Setup each User Code with the User Access Option Screen. Each
User Code can be set to be currently valid or not, or to have conditional
validity depending on a time and date schedule. Refer to the Users
Guide for details on setting User Code Access Schedules.
5. Press BACK when finished.
Figure 63. Set Date Screen
10. Press BACK to return to the Security Screen or press
the
button to return to the Home Screen.
The installation and installer programming of the Control Panel is
now complete. Continue to the next section to test the system.

Figure 59. User Management Screen

39

Installer Testing
Testing the System
After the installation is complete and the Control Panel
programming is complete, the system must be tested to ensure
proper operation.
System testing is performed through the Installer Toolbox screen.
1. From the Home Screen, press the lower right corner of the screen.
2. Enter the Installer Code (default = 1561) to access the Installer Toolbox.

Sounder Disable/Enable

Figure 64. Installer Toolbox

Since installer testing will cause the Control Panels internal and
external alarm sounder to activate, an option to lower the sounder
is available.
1. From the Installer Toolbox Screen, press DISABLE SOUNDER.
2. A confirmation screen will be displayed. Press OK. Four beeps
will sound from the internal sounder, and a short siren will sound
from the external sounder. The external siren will be disabled
and the internal sounder will be lowered for 30 minutes.
3. A second confirmation screen will be displayed to verify
that the test sounds were produced. Press OK.
4. While the sounder is disabled, the sounder disable
icon will be displayed on the status bar.

Figure 65. Sounder Disable Screen

The sounder disable will automatically time out after 30 minutes,

and the sounder will automatically become active again.
To re-enable the sounder manually, follow these steps:
1. From the Installer Toolbox Screen, press ENABLE SOUNDER.
2. A confirmation screen will be displayed. Press OK.

Zone Reporting Test

To verify that the Central Station will correctly receive reports from
each zone type, perform the following tests:
1. Inform the Central Station that test signals will be sent.
2. Trigger a 24-hour fire sensor (if installed) or press the FIRE
emergency button (if enabled), wait about 45 seconds for
the report to complete, then disarm the Console.

Figure 66. Sounder Disable Confirmation Screen

3. Trigger a 24-hour panic sensor (if installed) or press the

PANIC emergency button (if enabled), wait about 45 seconds
for the report to complete, then disarm the Console.
4. Trigger a 24-hour emergency sensor (if installed) or press the
EMERGENCY emergency button (if enabled), wait about 45
seconds for the report to complete, then disarm the Console.

STATUS BAR
SHOWING SOUNDER
IS DISABLED

5. Arm the system then trigger a burglary sensor, wait for

the system to go into alarm, wait about 45 seconds for
the report to complete then disarm the Console.
6. Check with the Central Station that each zone type was reported,
then inform the Central Station that the testing is complete.
Figure 67. Sounder Disable Icon on Status Bar

40

Installer Testing
Walk Test Mode
Walk Test Mode is for testing all the sensors. It verifies that each
sensor is being received correctly by the Control Panel. The walk
test also tests the Control Panels indicators and sounder.
NOTE: The Walk Test Mode will automatically end after 25
minutes.

Signal Strength Indicators

An important feature is the received signal strength indicators
displayed by the Control Panel for each of the sensors. Even though
the Control Panels RF receiver is high-sensitivity, reception quality
of sensors at the Control Panel can vary over time, depending on
the amount of background RF noise on the receivers operating
frequency. The signal strength indicators are an important aid to
the installer for determining the best location to mount the sensors
and Control Panel.
During the walk test, the Control Panel will display the signal strength
of the RF transmissions received from each of the sensors. This
will help identify any sensors that are received with a weak signal
at the Control Panel. Sensors with low signal strength might need
to be re-mounted to a location that produces stronger reception
at the Control Panel. The higher the sensor signal strength, the
better.

Figure 68. Installer Toolbox Screen

During the test, the system will beep every 30 seconds to indicate
that the system is in Walk Test Mode. During the last 5 minutes of
the test, the system will beep two times every 30 seconds.
NOTE: Entering the Walk Test Mode will send a start test
report to the Central Station. Exiting the Walk Test Mode will
send a stop test report to the Central Station.
To perform a walk test, follow these steps:

Figure 69. Sensor Test Screen During Testing

1. From the Installer Toolbox screen, press WALK TEST.

2. The
icon will display on the Control Panels status bar and a beep will
sound every 30 seconds to indicate that the system is in Walk Test Mode.
3. Each of the sensors and their status will be shown on the on the sensor
test screen. Use the and arrows to scroll through the sensor list.
4. Activate the first sensor listed and view the result on the display:
When a sensor is received by the Control Panel, three beeps will sound
and the display will light a green bar to the left of the sensors name.
The received signal strength of the sensor will display as one to five
green bars. The more bars, the higher the signal strength.

Figure 70. Sensor Test Screen Completed and Passed

If the signal level is sufficient, a check mark will display for the sensor.
For sensors with multiple loops, wait 15 seconds between
triggering each loop.
5. Continue testing with each of the other sensors listed.
6. After all the sensors have been tested, press the OK button
to test the Control Panels indicators and sounder.
7. Press each test item displayed, observe the Control Panel item
being tested, and answer the yes/no question for the test.
8. Press OK when all items have been tested. The Control
Panel will display a summary of the test results.

Figure 71. Indicator and Sounder Test Screen

9. Press OK to return to the Installer Toolbox.

41

Installer Testing
Radio Status Mode
NOTE: GSM Module must be installed to use this function.
The GSM Radio Status screen displays data for the GSM radio (if
installed).The screen displays signal strength, serial number, registration
status, and other information about the GSM radio module status. The
information may be helpful for radio installation troubleshooting.
Follow these steps to check the radio status:
1. From the Installer Toolbox screen, press the RADIO STATUS button.
2. The system will display the GSM Radio Info screen. Each
test item is displayed, followed with its current condition.
Scroll through the info screen with the and arrows.

Figure 72. Installer Toolbox Screen

Text is displayed in red if the tested signal strength is zero

or too low, or the GSM module is not registered.
Text is displayed in orange if the connection is
idle and the GSM module is registered.
Text is displayed in green if the signal strength is
good and the GSM module is registered.

GSM Radio Test

A RUN RADIO TEST button is provided on the GSM Radio Status
screen. Pressing this button will test the GSM cell phone connection
to the Central Station.

Figure 73. GSM Radio Info Screen

The same test can also be run using the CELL PHONE TEST button
on the User Toolbox screen #3.
Follow these steps to test the GSM radio:
1. From the Radio Status screen, press the RUN RADIO TEST button.
2. The system will display the Cell Phone Test screen. The top portion
of the screen shows the actions that the Control Panel is taking.
The bottom portion of the screen shows the results of the actions.
Scroll through the status screen with the and arrows.

Figure 74. GSM Radio Test Screen

3. When the test is complete, press OK to return to the Installer Toolbox.

Telephone Test
The telephone test checks the land-line connection to the Central
Station through the Control Panels built-in digital communicator.
The test is accessed through the User Toolbox screen #3.
Follow these steps to test the digital communicator:
1. On toolbox screen #3, press the TELEPHONE TEST button.
2. Enter the Master User Code, and the system will display the
Telephone Test screen. The top portion of the screen shows
the actions that the Control Panel is taking. The bottom
portion of the screen shows the results of the actions. Scroll
through the status screen with the and arrows.
3. When the test is complete, press OK to return to the User Toolbox.

Restoring Programming Defaults

To soft reset the Control Panel back to the factory defaults, use the
Restore Default option in the Installer toolbox.
NOTE: The Control Panel may also be hard reset to out-of-the-box factory
defaults by pressing and holding the emergency and home buttons while
applying power (if not disabled through programming questions Q-44 & Q-45).

Restore Defaults
The Restore Defaults screen provides a method to selectively reset the Control
Panel to its default programming values instead of using a full hard reset.
Two check box options are available; one or both must be checked:
If the ZONES box is checked, all data for the 48 sensors will be erased and
replaced with the default values.
If the CONSOLE box is checked, all the Control Panel programming
questions (except Z-Wave questions Q79-Q83) will be erased and replaced
with the default values. The User Codes will be erased, the backlight timeout
is reset to five minutes, and the brightness/volume settings are reset.

42

Figure 75. Restore Defaults Screen

Regulatory Information & Limited Warranty

Wireless Product Notice

Industry Canada Notices

Radio controls provide a reliable communications link and fill an

important need in portable wireless signaling; however, there are
some limitations which must be observed.

NOTICE: The ringer equivalence number (REN) assigned to each

terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the ringer
equivalence numbers of all the devices does not exceed 5.

For U.S. installations only: The radios are required

to comply with FCC Rules and Regulations
as Part 15 devices. As such, they have limited
transmitter power and therefore limited range.
A receiver cannot respond to more than one
transmitted signal at a time and may be blocked by
radio signals that occur on or near their operating
frequencies, regardless of code settings.
Changes or modifications to the device
may void FCC compliance.
Infrequently used radio links should be tested regularly
to protect against undetected interference or fault.
A general knowledge of radio and its vagaries should be
gained prior to acting as a wholesale distributor or dealer, and
these facts should be communicated to the ultimate users.

FCC Notice
This equipment generates and uses radio frequency energy and if
not installed and used properly, that is, in strict accordance with the
manufacturers instructions, may cause interference to radio and
television reception. It has been type tested and found to comply
with the limits for a Class B computing device in accordance with
Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Relocate the Console away from the TV/radio receiver.
Plug the Console into a different wall outlet so that
the Console is on a different branch circuit.
Re-orient the TV/radio antenna.
If necessary, the user should consult the
dealer or an experienced radio/television
technician for additional suggestions.

FCC Telephone Rules and Regulations

The FCC requires that this alarm dialer system not make more
than 15 repetitive dialing attempts to a single telephone number.
There are no limitations when the calls are made sequentially
to two or more alternative numbers, or when these calls are
spaced 10 minutes apart to a single number. The FCC Rules
and Regulations do not specify the re-attempt period as this can
vary for specific applications. When setting this period, take into
consideration local, interstate, foreign and special network call
completion characteristics, network processing time, a sufficient
number of rings and busy/dont answer modes.

NOTICE: The Industry Canada label identifies certified equipment.

This certification means that the equipment meets certain
telecommunications network protective, operational and safety
requirements. The Department does not guarantee the equipment
will operate to the users satisfaction.
Before installing this equipment, users should ensure that
it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and internal
metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.

Limited Warranty
This 2gig Technologies Inc. product is warranted against defects
in material and workmanship for twelve (12) months. This
warranty extends only to wholesale customers who buy
through 2gig Technologies Inc. authorized distribution channels.
2gig Technologies Inc. does not warrant this product to
consumers. Consumers should inquire from their selling dealer
as to the nature of the dealers warranty, if any. There are no
obligations or liabilities on the part of 2gig Technologies Inc.
for consequential damages arising out of or in connection
with use or performance of this product or other indirect
damages with respect to loss of property, revenue, or profit,
or cost of removal, installation, or reinstallation. All implied
warranties, including implied warranties for merchantability and
implied warranties for fitness, are valid only until the warranty
expires. This 2gig Technologies Inc. Warranty is in lieu of all
other warranties express or implied.
All products returned for warranty service require a Return Product
Authorization Number (RPA#). Contact 2gig Technologies Inc. at
866-670-1591 for an RPA# and other important details.

43

Reference Programming Question Table

Q#
Q-1

QUESTION
Select RF sensor # (01-48)
Select RF sensor (#) type

Q-1 SUB-QUESTIONS

Select RF sensor (#) equipment type

Q-2 SUB-QUESTIONS

Q-2

Q-3 SUB-QUESTIONS

Q-3

Q-4 SUB-QUESTIONS

Q-4

Q-5
Q-6
Q-7
Q-8
Q-9
Q-10
Q-11
Q-12
Q-13
Q-14
Q-15
Q-16
Q-17
Q-18
Q-19
Q-20
Q-21
Q-22
Q-23
Q-24
Q-25
Q-26
Q-27

44

Select RF sensor (#) equipment code

Enter RF sensor (#) other equipment code (0-9999)
Enter RF sensor (#) serial number (7 digits)
Select RF sensor (#) equipment age (0-1)
Select RF sensor (#) loop number (1-3)
Select RF sensor (#) dialer delay (0-1)
Construct RF sensor (#) voice descriptor
Select RF sensor (#) reports (0-1)
Select RF sensor (#) supervised (0-1)
Select RF sensor (#) chime (0-5)
Select wired sensor # (1-2)
Select wired sensor (#) type
Select wired sensor (#) equipment type
Enter wired sensor (#) equipment code (0-9999)
Select wired sensor (#) equipment age (0-1)
Select wired sensor (#) normal state
Select wired sensor (#) dialer delay (0-1)
Construct wired sensor (#) voice descriptor
Select wired sensor (#) reports (0-1)
Select wired sensor (#) chime (0-5)
Select fob # (1-8)
Select fob (#) used (0-1)
Select fob (#) equipment code (0000)
Enter fob (#) other equipment code (0-9999)
Enter fob (#) serial number (7 digits)
Select fob (#) equipment age (0-1)
Select fob (#) emergency key (0-4)
Select fob (#) key 2 can disarm (0-1)
Construct fob (#) voice descriptor
Select fob (#) arm no delay (0-1)
Select fob (#) key 4 output (0-2)
Select RF keypad # (1-4)
Select RF keypad (#) used (0-1)
Select RF keypad (#) equipment code
Enter RF keypad (#) other equipment code (0-9999)
Enter RF keypad (#) serial number (7 digits)
Select RF keypad (#) equipment age (0-1)
Select RF keypad (#) emergency keys (0-1)
Construct RF keypad (#) voice descriptor
Enter exit delay, in seconds (45-120)
Enter entry delay 1, in seconds (30-240)
Enter entry delay 2, in seconds (30-240)
Select dialer (0-1)
Enter dialing prefix (0-4 digits)
Enter call waiting disable code (0-6 digits)
Enter CS #1 phone number (0-25 digits)
Enter CS #1 account number (4 digits)
Select 2-way voice (0-2)
Select silent panic/burglary listen only (0-1)
Select dialing type (0-1)
Select police emergency key (0-2)
Select fire emergency key (0-1)
Select emergency key (0-1)
Select quick arming (0-1)
Select swinger shutdown count (1-6)
Select siren supervision time (0-3)
Enter CS lack of usage notification time (0-255)
Enter radio modem network failure time (0-255)
Select radio modem network failure causes trouble (0-1)
Select radio modem network failure reports (0-1)
Select auto stay (0-1)
Select exit delay restart (0-1)

DEFAULT
(00) unused
Varies by RF sensor type
(Only shown for some sensor types)
(0000) other
0 (Only shown if other is selected)
0000000
(0) new
Varies with sensor model selected
(1) enabled (except for fire & CO)
No default
(1) enabled
(1) enabled
(0) disabled
(00) unused
Varies by wired sensor type
(Only shown for some sensor types)
0
(0) new
(0) not used
(1) enabled
No default
(1) enabled
(0) disabled
(0) unused
(0000) other
0 (Only shown if other is selected)
0000000
(0) new
(0) disabled
(1) enabled
keyfob #
(0) disabled
(0) disabled
(0) unused
(0000) other
0 (Only shown if other is selected)
0000000
(0) new
(1) enabled
keypad #
60 seconds
30 seconds
45 seconds
(0) disabled
No default
No default
No default
No default
(1) stay on line
(1) enabled
(0) touch tone
(1) audible
(1) audible
(1) audible
(1) enabled
(2) two trips
(0) disabled
7 Days
30 minutes
(1) enabled
(1) enabled
(1) enabled
(1) enabled

Q#
Q-28
Q-29
Q-31
Q-32
Q-33
Q-34
Q-35
Q-36
Q-37
Q-38
Q-39
Q-40
Q-41
Q-42
Q-43
Q-44
Q-45
Q-46

QUESTION
Select quick exit (0-1)
Enter periodic test, in days (0-255)
Enter cancel time, in minutes (5-255)
Select cancel display (0-1)
Select cross sensor 47-48 (0-1)
Enter cross sensor timeout, in seconds (10-120)
Select abort window dialer delay (0-2)
Select burglary bell cutoff (0-4)
Select fire bell cutoff (0-4)
Enter time to detect AC loss, in minutes (0-30)
Select random AC loss report time (0-1)
Enter CS #2 phone number (0-25 digits)
Enter CS #2 account number (4 digits)
Select remote control phone (0-3)
Enter installer code (4 digits)
Select lock installer programming (0-2)
Select lock default programming (0-2)

Select trouble doesnt sound at night (0-1)

Select trouble resound after holdoff (0-7)
Enter download csid (6 digits)
Select programming mode entry reports to CS (0-1)
Select trouble reports to CS (0-1)
Select manual bypass reports to CS (0-1)
Select AC loss reports to CS (0-1)
Select system low battery reports to CS (0-1)
Select RF low battery reports to CS (0-1)
Select opening reports to CS (0-1)
Select closing reports to CS (0-1)
Select alarm restore reports to CS (0-1)
Select trouble restore reports to CS (0-1)
Select bypass restores reports to CS (0-1)
Select AC restore reports to CS (0-1)
Select system low battery restore reports to CS (0-1)
Select RF low battery restores reports to CS (0-1)
Select phone fail detect (0-1)
Select smart test reports (0-1)
Select RF jam causes trouble (0-1)
Select daylight saving (0-1)
Select daylight saving start month (01-12)
Select daylight saving start Sunday (1-7)
Select daylight saving end month (01-12)
Select daylight saving end Sunday (1-7)
Select system tamper causes trouble (0-1)
Select quick bypass (0-1)
Select disarming keyfob after alarm (alert) (0-1)
Select keyfob arm / disarm confirmation (0-1)
Select auto unbypass for manual bypass (0-1)
Select force bypass reports (0-1)
Select event log (0-3)
Select output (00-10)
Select Z-Wave feature (0-3)
Select Z-Wave switches feature (0-1)
Select Z-Wave thermostats feature (0-1)
Select Z-Wave door locks feature (0-1)
Select temperature display units (0-1)
Select services require master code (0-1)
Select master user access to zwave toolbox (0-1)
Select disable siren after two-way audio (0-1)
Select keyfob/remote arming mode on system not
Q-87
ready (0-2)
Q-88 Select siren mode (0-1)
Default set for SIA CP-01 compliance
Q-47
Q-48
Q-49
Q-50
Q-51
Q-52
Q-53
Q-54
Q-55
Q-56
Q-57
Q-58
Q-59
Q-60
Q-61
Q-62
Q-63
Q-64
Q-65
Q-66
Q-67
Q-68
Q-69
Q-70
Q-71
Q-72
Q-73
Q-74
Q-75
Q-76
Q-77
Q-78
Q-79
Q-80
Q-81
Q-82
Q-83
Q-84
Q-85
Q-86

DEFAULT
(1) enabled
30 days
5 minutes
(1) enabled
(0) disabled
10 seconds
(1) 30 seconds
(0) 4 minutes
(0) 4 minutes
10 minutes
(1) enabled
No default
No default
(3) data and voice
1561
(0) disabled
(0) default all
(1) enabled
(0) disabled
000000
(0) disabled
(1) enabled
(0) disabled
(1) enabled
(1) enabled
(1) enabled
(0) disabled
(0) disabled
(0) disabled
(1) enabled
(0) disabled
(1) enabled
(1) enabled
(1) enabled
(0) disabled
(0) disabled
(0) disabled
(1) enabled
(03) March
(2) 2nd
(11) November
(1) 1st
(1) enabled
(0) disabled
(0) disabled
(0) disabled
(1) enabled
(0) disabled
(3) all events
(11) follows internal sounder alarm
(1) disabled but visible
(0) disabled
(0) disabled
(0) disabled
(0) degrees Fahrenheit
(0) disabled
(0) disabled
(0) disabled
(0) auto-bypass with zone
participation on restore
(0) sound for burglary and fire/CO

For UL985 Installations, this feature must be disabled

Reference System Vocabulary Table

#
002
003
004
005
006
007
008
009
010
011
012
013
014
015
016
017
018
019
020
021
022
023
024
025
026
027
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
048
049
050
051
052
053
054
055
056
057
058
059
060
061
062
063
064
065
066
067
068
069

WORD
ABORT
AC
ACCESS
ALARM
AND
ANNOUNCEMENT
AREA
ARM
ARMED
ARMING
AT
ATTIC
AUDIO
AUTO
AUTOMATION
AUXILIARY
AWAY
BABYS
BACK
BASEMENT
BATHROOM
BATTERY
BEDROOM
BONUS
BREAK
BUTTON
BYPASS
BYPASSED
CABINET
CANCEL
CARBON MONOXIDE
CELLAR
CELLULAR
CELL RADIO
CENTER
CHECK
CHEST
CHILDRENS
CHIME
CLOSET
CODE
COMMUNICATIONS
COMPUTER
CONTROL
COOL
CRAWL
CURRENT
DAY
DEGREES
DEN
DETECTOR
DIM
DINING
DISARM
DISARMED
DOCK
DOOR
DOWNSTAIRS
DRIVEWAY
EAST
EIGHT
EIGHTEEN
EIGHTY
ELECTRIC
ELEVEN
EMERGENCY
ENTER
ENTRANCE

#
070
071
072
073
074
075
076
077
078
079
080
081
082
083
084
085
086
087
088
089
090
091
092
093
094
095
096
097
098
099
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137

WORD
ENTRY
ERROR
EXERCISE
EXIT
EXIT NOW
EXTERIOR
EXTERNAL
FAILURE
FAMILY
FAN
FIFTEEN
FIFTY
FIRE
FIRE ALERT
FIRE DETECTOR
FIRST
FIVE
FLOOD
FLOOR
FLUID
FOIL
FOR
FORTY
FOUR
FOURTEEN
FOURTH
FREEZE
FREEZER
FRONT
FURNACE
GAME
GARAGE
GAS
GLASS
GLASS BREAK
GUEST
GUN
HALL
HALLWAY
HANGING
HANG UP
HEAT
HIGH
HOME
HOUSE
ICE
INSIDE
INSTANT
INTERIOR
INTRUSION
IS
KEY
KEYFOB
KEYPAD
KIDS
KITCHEN
LAUNDRY
LEFT
LEVEL
LIBRARY
LIGHT
LIGHTS
LIQUOR
LIVING
LOADING
LOCK
LOFT
LOW

#
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205

WORD
MAIN
MAINTENANCE
MASTER
MEDICAL
MEDICINE
MENU
MIDDLE
MONITOR
MOTION
MOTION DETECTOR
MUD
NINE
NINETEEN
NINETY
NORTH
NOT
NOT READY
NO DELAY
NO ENTRY DELAY
NURSERY
OFF
OFFICE
ON
ONE
ONE HUNDRED
OUTPUT
OUTSIDE
PANEL
PANIC
PANTRY
PATIO
PERIMETER
PHONE LINE
PLAY
POLICE
POOL
POUND
POWER
PRESS
PREVIOUS
PUMP
RADIO
READY
REAR
RELAY
REMOTE
REPEAT
RF JAM
RIGHT
ROOM
SAFE
SECOND
SECURITY
SENSOR
SENSORS
SESSION
SET
SEVEN
SEVENTEEN
SEVENTY
SHED
SHOP
SIDE
SILENT
SIREN
SIX
SIXTEEN
SIXTY

#
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271

WORD
SKYLIGHT
SLIDING
SMOKE
SOUNDER
SOUTH
SPACE
SPARE
STAIRS
STAR
STATUS
STAY
STOP
STORAGE
STUDY
SUMP
SUPERVISION
SYSTEM
TAMPER
TEMPERATURE
TEN
TERMINATED
THERMOSTAT
THIRD
THIRTEEN
THIRTY
THREE
TO
TOOL
TRANSMITTED
TRANSMITTER
TROUBLE
TURN
TWELVE
TWENTY
TWO
UNLOCK
UPPER
UPSTAIRS
USER
UTILITY
VALVE
VOICE
WALL
WATER
WEST
WINDOW
WIRELESS
YARD
ZERO
ZONE
BALCONY
COURTYARD
DECK
DETACHED
OVERHEAD
REFRIGERATOR
SERVICE
SUNROOM
WAREHOUSE
GATE
APARTMENT
FOYER
TV
VIDEO
PORCH
CORNER

45

Notes

46

Notes

47

Index
#s
2GIG-AC1 replacement power supply 7
2GIG-ANT1 internal GSM antenna 7
2GIG-ANT1X external in-wall GSM antenna 7
2GIG-ANT2X external attic mount GSM antenna 7
2GIG-ANT4X 7
2GIG-BATT1 standard battery pack 7
2GIG-BATT1X extended battery pack 7
2GIG-DW10 thin door/window contact 6
2GIG-DW20R recessed door contact 6
2GIG-GB1 glass break detector 6
2GIG-GSMx GSM module 7
2GIG-KEY2 4-button key ring remote 6
2GIG-PANIC1 panic button remote 6
2GIG-PIR1 passive infrared motion detector 6
2GIG-SMKT2 smoke and heat detector 6
2GIG-TAKE-345 6
2GIG-TS1 Wireless touch screen keypad 6
2-way voice central station commands 30
2-way voice enable 30
4-button key ring remote 6
24-hour Audible Alarm sensor type 18
24-hour Auxiliary Alarm sensor type 18
24-hour Carbon Monoxide sensor type 18
24-hour Fire sensor type 18
24-hour Fire with Verification sensor type 18
24-hour Silent Alarm sensor type 18

D
Daylight saving end month 36
Daylight saving end Sunday 36
Daylight saving scheme 36
Daylight saving start month 36
Daylight saving start Sunday 36
Day Zone sensor type 18
DELETE button 15
Dialer enable 30
Dialing prefix 30
Dialing type 31
Disable siren after 2-way audio 38
Disarming with key fob alert after alarm 36
Download csid 34

E
Emergency button 31
END button 15
Entry delay 1 30
Entry delay 2 30
ESC button 15
ETL Listing 2
Event log 37
EXIT button 15
Exit delay 30
Exit delay restart 32
Exit/Entry 1 sensor type 18
Exit/Entry 2 sensor type 18
Exiting programming 39
Extended battery pack 7
External attic mount GSM antenna 7
External in-wall GSM antenna 7

A
Abort window dialer delay 32
AC loss detect time 33
AC loss reports 35
AC loss report time 33
AC power icon 14
AC restore reports 35
Alarm restore reports 35
Alarm sounder 9
Alarm system permit 2
Arming screen 12
Auto stay 31

F
Fire bell cutoff 33
Fire emergency key 31
Force bypass reports 37
FWD button 15

G
Glass break detector 6
GO TO button 15
GSM module 7
GSM module installation 10
GSM radio icon 14
GSM radio test 42

B
BACK button 15
Backlight timeout 39
Backup battery connection 11
Backup battery status icon 14
Bell terminals 9
BKSP button 15
Block diagram 3
Brightness / volume 39
Burglary bell cutoff 32
Bypass restore reports 35

H
Hardwired loops 8
Home screen 12

I
INSERT button 15
Installation outline 5
Installer code 33
Installer code entry 13
Installer programming 20, 22
Installer toolbox 13
Insurance discounts 2
Interior follower sensor type 18
Interior sensor open icon 14
Interior with delay sensor type 18
Internal GSM antenna 7

C
Call waiting disable code 30
Cancel display 32
Cancel time 32
Central station #1 account number 30
Central station #1 phone number 30
Central station #2 account number 33
Central station #2 phone number 33
Central station commands for 2-way voice 30
Closing reports 35
Communicator telephone line 9
Control panel external features 4
Control panel features 4
Control panel internal features 4
Control panel location 5
Control panel location height 5
Control panel mounting 11
Control panel mounting plate 8
Control panel wiring 11
Control panel wiring diagram 2
Cross sensor 32
Cross sensor timeout 32
CS Lack of usage notification time 31

K
Key fob # 27
Key fob arm / disarm confirmation 36
Key fob arm no delay 27
Key fob emergency key 27
Key fob equipment age 27
Key fob equipment code 27
Key fob key 2 can disarm 27
Key fob key 4 output 27
Key fob serial number 27
key fob summary screen 26
Key fob voice descriptor 27

L
LEARN button 15
Location of sensors 5
Lock default programming 34
Lock installer programming 34

M
Manual bypass reports 34
Master user access to Z-Wave Toolbox 38
Menu screen 12

48

Index
N

S
Navigation arrows 15
NFPA Standard #72 ii
No response sensor type 18

Saving programming 39
Security screen 12
Select keyfob/remote arming mode on system not ready 38
Select siren mode 38
Sensor signal loss through materials 5
Sensor types 18
Sensor zones 18
Services menu requires master code 38
Set date / time 39
SET TIME button 39
SHIFT button 15
Signal strength indicators 41
Silent burglary sensor type 18
Silent panic/burglary listen only 30
Siren supervision time 31
SKIP button 15
Smart test reports 36
Smoke and heat detector 6
Smoke detector location ii
Solid state output 9
Sounder disable/enable 40
Sounder disable icon 14
Standard battery pack 7
Status screen 12
SUM button 15
Super switch wireless takeover module 6
Swinger shutdown count 31
System block diagram 3
System configuration screen 13
System low battery reports 35
System low battery restore reports 35
System sensor types 18
System status icons 14
System tamper causes trouble 36
System vocabulary 19

O
Open collector output selection 37
Opening reports 35

P
Panic button remote 6
Passive infrared motion detector 6
PASTE button 15
Perimeter sensor type 18
Periodic test timer 32
Phone fail detect 35
Phone line failure icon 14
Police emergency key 31
Power supply mounting 11
Power supply wiring 11
Programming mode entry reports 34
Programming outline 16
Programming question list 17

Q
Quick arming 31
Quick bypass 36
Quick exit 32

R
Radio modem network failure causes trouble 31
Radio modem network failure reports 31
Radio modem network failure time 31
Radio status mode 42
Recessed door contact 6
Reference programming question table 44
Reference system vocabulary 45
Regulatory information 43
Remote control phone enable 33
Replacement power supply 7
Restoring programming defaults 42
RF jam causes trouble 36
RF key fob programming 26
RF key fob programming outline 26
RF key fob programming steps 27
RF key fob summary screen 26
RF keypad # 29
RF keypad emergency key 29
RF keypad equipment age 29
RF keypad equipment code 29
RF keypad other equipment code 29
RF keypad programming 28
RF keypad programming outline 28
RF keypad programming steps 29
RF keypad serial number 29
RF keypad summary screen 28
RF keypad voice descriptor 29
RF low battery reports 35
RF low battery restore reports 35
RF sensor # 22
RF sensor chime 23
RF sensor dialer delay 23
RF sensor equipment age 23
RF sensor equipment code 22
RF sensor equipment type 22
RF sensor loop number 23
RF sensor other equipment code 22
RF sensor programming 20
RF sensor programming outline 20
RF sensor programming steps 22
RF sensor reports 23
RF sensor serial number 23
RF sensor summary screen 21
RF sensor supervised 23
RF sensor type 22
RF sensor voice descriptor 23
RJ31X telephone jack 9

T
Takeover module 6
Telephone line 9
Telephone test 42
Temperature display units 37
Testing the system 40
Test mode icon 14
Thin door/window contact 6
Toolbox screens 13
Touch screen keypad traffic icon 14
Trouble doesnt sound at night 34
Trouble reports 34
Trouble resound after holdoff 34
Trouble restore reports 35

U
Unused zone 18
User Management 39

V
Vocabulary 19

W
Walk test mode 41
Wall mounting control panel 8
Wired sensor # 25
Wired sensor chime 25
Wired sensor dialer delay 25
Wired sensor equipment code 25
Wired sensor equipment type 25
Wired sensor normal state 25
Wired sensor programming 24
Wired sensor programming outline 24
Wired sensor programming steps 25
Wired sensor reports 25
Wired sensor summary screen 24
Wired sensor type 25
Wired sensor voice descriptor 25
Wireless installation tips 5
Wireless keypad 6
Wireless sensor installation 8
Wireless takeover module 6
Wireless touch screen keypad 6
Wiring diagram 2

Z
Zone reporting test 40
Zone types 18
Z-Wave door locks feature 37
Z-Wave feature enable 37
Z-Wave switches feature 37
Z-Wave thermostats feature 37

49

Copyright 2012

v 1.9

233497 X8