Scribd
Upload
171 views

Chapter 7 - Part 2

This document discusses dimensional analysis and dimensionless groups in fluid mechanics. It begins by introducing common dimensionless groups such as Reynolds number, Froude number, Euler number, Weber number, and Mach number. These groups arise from dimensional analysis and are useful for characterizing different fluid phenomena. The document then discusses the concept of similitude and how it allows experiments on models to predict prototype behavior if geometric, kinematic, and dynamic similarity are satisfied through matching dimensionless groups. Examples are provided to demonstrate how to determine wind tunnel conditions needed to match prototype flow and how to scale measured model forces to the prototype.

Uploaded by

Vinot Esan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
171 views

Chapter 7 - Part 2

This document discusses dimensional analysis and dimensionless groups in fluid mechanics. It begins by introducing common dimensionless groups such as Reynolds number, Froude number, Euler number, Weber number, and Mach number. These groups arise from dimensional analysis and are useful for characterizing different fluid phenomena. The document then discusses the concept of similitude and how it allows experiments on models to predict prototype behavior if geometric, kinematic, and dynamic similarity are satisfied through matching dimensionless groups. Examples are provided to demonstrate how to determine wind tunnel conditions needed to match prototype flow and how to scale measured model forces to the prototype.

Uploaded by

Vinot Esan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 28

Dr.

Mohammad Shakir Nasif


Email: [email protected]

Tel: 05-3687026

Office Location: 17-03-11


3/10/2015 1:46 PM

Chapter 7 Assignment
Question: 7.3, 7.7, 7.29, 7.43, 7.45, 7.52, 7.80
Quiz: Monday or Tuesday 16 or 17 March
2015.
Quiz will start 5 minutes from the start of the
lecture) so make sure you arrive before the
time).

Some comments about


dimensional analysis
There are also other methods in dimensional
analysis but the method of repeating variables
is the easiest.
There is not a unique set of pi terms which
arises from a dimensional analysis. However,
the required number of pi terms is fixed.

Common Dimensionless Groups in


Fluid Mechanics
From dimensionless terms, many variables arise which are commonly used
in fluid mechanics problems.
Fortunately not all of these variables are used in one problem, however if
combination of some of these variables are present, it is a standard practice
to combine them into dimensionless groups (PI terms).
These combinations appear so frequent that special names are associated
with them.

It is also possible to provide physical interpretation to the dimensionless


groups which can be helpful in assessing their influence in particular
application.

Common Dimensionless Groups in


Fluid Mechanics
For example:

VL

This term is dimensionless, which is very well known in fluid mechanics, heat
VL
transfer.etc. It is called Reynolds number (Re).

Re

The physical interpretation to the


dimensionless term (Reynolds number ) is

VL Inertia force
Re

Viscous force

When flow enters any region there will be some


disturbances. If the flow velocity is not too fast, these
disturbances get damped out by the fluid viscosity.
We can see that the velocity in Reynolds number is on top
and the viscosity is on the bottom. For a large Reynolds
number this means that the velocity X length are large
compared to the viscosity.
At a certain large Reynolds number, the flow is moving too
fast for the viscosity to damp out the disturbance, hence it is
called turbulent flow.

Common Dimensionless Groups in Fluid Mechanics


These groups have
be developed by
using dimensional
analysis, then it
has been realised
that they have
been widely
repeated in
research. Hence
they were given
names.

Common Dimensionless Groups in


Fluid Mechanics (cont.)
Froude number (Fr no): It is the ratio of the inertia force on
an element of fluid to the weight of the element.

It is important in problems involving the study of flow of


water around ships, or flow through rivers or open
conduits.

Common Dimensionless Groups in


Fluid Mechanics (cont.)
Euler number (Eu no): Represents the ratio of the
pressure force to the inertia force.

It is normally used where pressure or pressure difference


between two points is an important variables.

For problems where cavitation is of concern, this number


is commonly used.
It can be also called as Cavitation number

Common Dimensionless Groups in


Fluid Mechanics (cont.)
Weber number (We no). It is the ratio of inertia force to
surface tension force.

It is important in problems in which there is an interface


between two fluids, in this situation the surface tension will
play an important role.

Common Dimensionless Groups in


Fluid Mechanics (cont.)
Mach number (Ma number): Represents the ratio of the fluid
speed to the sonic speed.

For jet fighters or airplanes fly with a speed higher than sonic
speed, the Ma >1.
If less than sonic speed Ma<1.
If equal to sonic speed Ma=1

Flow Similarity and Model Studies


A question comes to our mind whats the importance of all these
numbers and how we can use them.
These numbers applies when we want to study certain phenomena
and it is not possible to construct full scale model. Therefore we
can construct small scale model and use the same numbers in our
study.
We call it Similarity between full scale and small scale model.
Geometric Similarity
Model and prototype have same shape
Linear dimensions on model and prototype correspond within
constant scale factor
Kinematic Similarity
Velocities at corresponding points on model and prototype differ
only by a constant scale factor
Dynamic Similarity
Forces on model and prototype differ only by a constant scale
factor

Flow Similarity and Model Studies


Example: Drag on a Sphere

Flow Similarity and Model Studies


Example: Drag on a Sphere
For dynamic similarity

then

What is Concept of Similitude?


Similitude is the study of predicting prototype
conditions (flow, pressure distribution.etc.)
from model (small model) test observation.

Concept of Similitude
The concept of similitude is used so that
measurements made on one system (for
example, in the laboratory) can be used to
describe the behavior of other similar systems
(outside laboratory)

Modeling and Similitude


A model is a representation of a physical system that
may be used to predict the behavior of the system in
some desired respect.
The physical system for which the predictions are to
be made is called the prototype.
Usually a model is smaller than the prototype and
therefore, easier to handle in the lab.

Modeling and Similitude (cont.)


Model Design Conditions (or Similarity Requirements
or Modeling Laws)
To achieve similarity between model and prototype
behavior, all the corresponding pi terms must be
equated between model and prototype
Geometric Similarity
Dynamic Similarity
Kinematic Similarity

Modeling and Similitude (cont.)


Geometric Similarity
A model and prototype are geometrically
similar if and only if all body dimensions in
all three coordinates have the same linearscale ratio. All angles are preserved in
geometric similarity. All flow directions are
preserved. The orientations of model and
prototype w.r.t. the surroundings must be
identical.

Modeling and Similitude (cont.)


Kinematic Similarity
Velocities are related to the full scale by a
constant scale factor. They also have the
same directions as in the full scale.

Modeling and Similitude (cont.)


Dynamic Similarity
Forces are related to full scale by a constant
factor. Also requires geometric and kinematic
similarity.

Similitude Summary

Example 3
The drag on a 2-m-diameter satellite dish due to an 80 km/hr wind is to be
determined through a wind tunnel test using a geometrically similar 0.4-mdiameter model dish. Assume standard air for both model and prototype.
(a) At what air speed should the model test be run?
(b) With all similarity conditions satisfied, the measured drag on the model
was determined to be 170 N. What is the predicted drag on the prototype
dish?

Example 3 Solution
The drag on a 2-m-diameter satellite dish due to an 80 km/hr wind is to be
determined through a wind tunnel test using a geometrically similar 0.4m-diameter model dish. Assume standard air for both model and
prototype.
(a) At what air speed should the model test be run?
(b) With all similarity conditions satisfied, the measured drag on the
model was determined to be 170 N. What is the predicted drag on the
prototype dish?

Example 3 Solution
The drag on a 2-m-diameter satellite dish due to an 80 km/hr wind is to be
determined through a wind tunnel test using a geometrically similar 0.4m-diameter model dish. Assume standard air for both model and
prototype.
(a) At what air speed should the model test be run?
(b) With all similarity conditions satisfied, the measured drag on the
model was determined to be 170 N. What is the predicted drag on the
prototype dish?
Drag force

Example 4
The drag on an airplane shown in Fig.E7.7 cruising at 386
km/h in standard air is to be determined from tests on a
1:10 scale model placed in a pressurized wind tunnel. To
minimize compressibility effects, the air speed in the wind
tunnel is also to be 386 km/h.
Determine:
a)The required air pressure in the tunnel (assuming the
same air temperature for model and prototype), and
b)The drag on the prototype corresponding to a measured
force of 4 N on the model.

Example 4
a) Drag can be predicted from a geometrically similar model if the Reynolds numbers of the
prototype and the model are the same. Thus:

For this example, Vm = V and lm/l = 1/10 so that:

And therefore

The result shows that the same fluid with m = and m = cant be used if Reynolds number
similarity to be maintained. Instead, we can pressurize the wind tunnel to increase the density
of the air (with assumption that increase in density doesnt significantly change the viscosity).

Example 4
Therefore, if the viscosity is the same, the equation becomes:

For an ideal gas, p = RT so that:

And therefore the wind tunnel need to be pressurized so that:

Since the prototype is at standard atmospheric pressure, the required pressure in the wind
tunnel is:

Example 4
b) The drag could be obtained from:

or

Thus, for a drag of 4 N on the model the corresponding drag on the prototype is:

You might also like