Scribd
Upload
61 views

PPG Protective and Marine Coatings ABC #3: Ablative Antifouling Coating

This document provides product data and application instructions for an ablative antifouling coating. It lists the manufacturer, product designation, and technical representative contact information. It also details properties like solids content, flash point, viscosity, dry times, and application procedures.

Uploaded by

hainguyenbkvhv
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
61 views

PPG Protective and Marine Coatings ABC #3: Ablative Antifouling Coating

This document provides product data and application instructions for an ablative antifouling coating. It lists the manufacturer, product designation, and technical representative contact information. It also details properties like solids content, flash point, viscosity, dry times, and application procedures.

Uploaded by

hainguyenbkvhv
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

NAVSEA REVIEWED ASTM F-718

PPG Protective and Marine Coatings


ABC #3
Ablative Antifouling Coating
MIL-PRF-24647

If this product is to be applied as part of a coating system, all components of the system must
be as listed on the QPL.

This NAVSEA-REVIEWED ASTM F-718 data sheet is the only data sheet approved for use
when utilizing this coating for U.S. Navy preservation projects. NAVSEAs review covers only
the application process for the material. The review does not denote the material as a qualified
product, nor does it constitute an approval for purchase/procurement of the material. For
products on the Qualified Products List (QPL) for this MILSPEC, please refer to
https://assist.daps.dla.mil/quicksearch/
Questions regarding modifications or updates of this ASTM F-718 shall be directed toward:
NSWCCD
(215) 897-7411
[email protected]

NST Center ID#: 1183

NAVSEA Reviewed: 21 Sep 2010

ASTM F 718
SHIPBUILDERS AND MARINE PAINTS AND COATINGS PRODUCT/PROCEDURE DATA SHEET
CONTINUATION SHEET USED:

YES

NO

Date: 8/2010 Rev. 3


I. GENERIC TYPE AND DESCRIPTION: Ablative Antifouling Coating
Specification Number, Type, Class and/or Grade (If Applicable): MIL-PRF-24647

W
ED

II. MANUFACTURERS DATA:


(a) MANUFACTURER: PPG Protective and Marine Coatings
11605 Vimy Ridge Road, Alexander, AR 72202
(b) PRODUCT DESIGNATION: ABC #3
(c) COLOR(S): Red, Black
(d) USES: Underwater hull anti-fouling coating
(e) TECHNICAL SERVICE REPRESENTATIVE
Paul Whitehead (678) 472-8284
(f) NOT RECOMMENDED FOR: N/A

(b) % WEIGHT SOLIDS (ASTM D 1475): 81.16


(c): FLASH POINT (ASTM TEST METHOD D 93 OR D 56 OR D 3278): 83F

EV

(d): WEIGHT PER VOLUME: (FTMS 141a4184.1): 16.7 18.3 lbs / gal

IE

III. PROPERTIES:
(a) % VOLUME SOLIDS (ASTM D 2697): 52% 3%

(e) % EDGE RETENTION (IF REQUIRED BY APPLICABLE SPECIFICATION): N/A


(f): SHELF LIFE: 3 years from date of manufacture

): COMPONENT A: 70 110 KU

(g) VISCOSITY (STATE TEST METHOD TO BE USED:

(h) PACKAGING: 5 gallon pails


(i): NUMBER OF COMPONENTS: 1

(j) GLOSS (ASTM D 523): <5 (Flat)

COMPONENT B: NA

(k) STORAGE REQUIREMENTS: TEMP. MIN. 40F MAX. 100F

SE

ADDITIONAL PAINT STORAGE REQUIREMENTS: Product should be stored at temperatures of 40F 100F. The product may be subject to temperatures from
0F to 140F during transport for up to 30 days without adverse effects. If the product is exposed to more extreme temperatures or for a longer duration, please contact PPG
technical services for an evaluation. Product temperatures must be 50F 90F during mixing and application, unless otherwise stated in section V1.a. Note: Per NAVSEA
Standard Item 009-32, storage requirements are MIN 65F and MAX 85F.
(l) VOLATILE ORGANIC COMPOUND (EPA TEST METHOD 24): 3.3 lbs / gal.
(m) WEIGHT OF DRY FILM (WEIGHT/FT2 AT 1 MIL THICKNESS): 0.016 lbs 3%

AV

(n): SPECIAL PROPERTIES (e.g., STAIN RESISTANCE, LOW SOLAR ABSORBANCE, MOISTURE TOLERANCE): N/A

IV. SURFACE PREPARATION MINIMUM REQUIREMENTS (USE SPECIFIC STANDARD NUMBERS):


(a) INITIAL For anticorrosive primer: Abrasive blast to SSPC-SP 10, Ultra High Pressure Water Jet to SSPC-SP 12/WJ-2L or otherwise refer to NAVSEA Standard Item 009-32.
Primer surface must be clean and free of condensation or contaminants.

(b) TOUCH-UP Clean, dry surface

(c) PROFILE (INCLUDE METHOD USED) - MIN. 2 mils MAX. 4 mils (for anti-corrosive primer)
(d) SPECIAL INSTRUCTIONS - None
(e) PRIMER REQUIREMENTS (IF APPLICABLE): Amercoat 235, 240, or 385
(f) MAXIMUM ALLOWABLE CONDUCTIVITY (BRESLE PATCH METHOD): 30 mg/m2
(g) MAXIMUM DEGREE OF FLASH RUSTING ALLOWABLE (LIST COMMERCIAL STANDARD): SSPC-SP 12/WJ-2L

NST Center ID#: 1183

NAVSEA Reviewed: 21 Sep 2010

SPECIAL SAFETY PRECAUTIONS:


See MSDS

V. MIXING PROCEDURES:
(a) MIXING RATIOS BY WEIGHT N/A
BY VOLUME N/A
(b) INDUCTION TIME N/A

(d) THINNING REQUIREMENTS (RATIO) NO THINNING ALLOWED


NA Hr(s) @

(e) POT LIFE -

W
ED

(c) RECOMMENDED SOLVENT THINNING NO THINNING ALLOWED


CONFINED AREAS - NO THINNING ALLOWED
NON-CONFINED AREAS - NO THINNING ALLOWED
CLEAN UP T-10

(f) SPECIAL INSTRUCTIONS Power mix to ensure pigment is uniformly suspended. Ensure good off-bottom mixing.

VI. APPLICATION:
(a) ENVIRONMENTAL LIMITATIONS SUBSTRATE TEMPERATURE: MIN. 20F MAX. 120F

IE

MINIMUM SUBSTRATE TEMPERATURE DIFFERENCE ABOVE THE DEW POINT - 5F


RELATIVE HUMIDITY: Refer to NAVSEA Standard Item 009-32
AMBIENT TEMPERATURE: MIN. 20F MAX. 120F

EV

(b) FILM THICKNESS (SSPC-PA 2):


PER COAT:
WET MIN. 8 mils WET MAX. 12 mils
DRY MIN. 4 mils DRY MAX. 6 mils
TOTAL SYSTEM:

DRY MAX. Refer to NAVSEA Standard Item 009.32

(c) DRY TIMES (ASTM D 1640)

70F (21C)
5 hours

90F (32C)
3 hours
4 hours
4 hours

6 hours
6 hours

50F (10C)
10 hours
Unlimited
12 hours
12 hours

32F (0C)
20 hours

20F (-7C)
48 hours

24 hours
24 hours

72 hours
72 hours

SE

Dry to Recoat (min)*


Maximum recoat *
Dry to Handle
Full Service **

DRY MIN.

(d) EQUIPMENT REQUIREMENTS (INCLUDE PREFERRED, SUITABLE, NOT SUITABLE REQUIREMENTS) Standard airless spray with a minimum of a 45:1 (minimum)
pump ratio with 0.021-0.025 spray tip, or- natural bristle brush, or phenolic core roller.
IF PLURAL COMPONENT EQUIPMENT IS REQUIRED, STATE SO N/A
IF HEATED LINES ARE REQUIRED, STATE SO N/A

AV

(e) SPECIAL INSTRUCTIONS Must be applied to primer that is tack-free but soft to finger pressure.

REPAIR PROCEDURES IF THE OVERCOAT WINDOW HAS BEEN EXCEEDED: Refer to NAVSEA Standard Item 009-32.

NST Center ID#: 1183

NAVSEA Reviewed: 21 Sep 2010

You might also like