GREE COMMERCIAL AIR CONDITIONERS

AIR-TO-WATER HEAT PUMP

INSTALLATION

AIR-TO-WATER HEAT PUMP

INSTALLATION

INSTALLATION
1 INSTALLATION OF UNITS
1.1 Installation Positions
1.1.1 Installation Positions of Outdoor
Outdoor unit must be installed on a firm and solid support.
Outdoor unit shall be installed close to the indoor unit, hence to minimize the length and
bends of cooling pipe.
Avoid placing the outdoor unit under window or between two constructions, hence to prevent
normal operating noise from entering the room.
Air flow at inlet and outlet shall not be blocked.
Install at a well-ventilated place, so that the machine can absorb and discharge sufficient air.
Do not install at a place where flammable or explosive goods exist or a place subject to
severe dust, salty fog and polluted air.
1.1.2 Installation Positions of Indoor
Avoid direct sunshine.
Ensure the hanger rod, ceiling and building structure have sufficient strength to support the
weight of air conditioner unit.
Drainage pipe is easy to connect out.
Indoor and outdoor connection pipes are easy to go outdoors
Do not install at a place where flammable or explosive goods exist or flammable or explosive
gas might leak.
Do not install at a place subject to corrosive gas, severe dust, salty fog, smoke or heavy
moisture.
Air flow at inlet and outlet air is not blocked.
Note:
The water pressure gage is installed in returning water line in the indoor unit
Please adjust the hydraulics system pressure according to next item:
If the pressure is less than 0.5 bar, please recharge the water immediately;
when rechargingthe hydraulics system pressure should be not more than 2.5Bar.
1.1.3 Installation Positions of Water Tank
The insulated water tank should be installed and keep levelly within 5m and vertically within
3m from the Indoor unit. It can be installed in the room.
Standing water tank must be installed vertically with the bottom on the ground, never
suspended. Installation place must be firm enough and the water tank should be fixed on the
wall with bolts to avoid vibration, as shown in the following figure. Weight capacity of water
tank during installation should also be considered.

AIR-TO-WATER HEAT PUMP

INSTALLATION

The minimum clearance from the water tank to combustible surface must be 500mm.
There should be water pipe, hot water joint and floor drain near the water tank in favor of
water replenishment, hot water supply and drainage of water tank.
Connection of inlet/outlet waterway: Connect the safety check valve attached with the unit
( points at insulated water tank) with the water inlet of water tank with PPR pipe according
to the following figure, sealing with unsintered tape. The other end of the safety check valve
should connect with tap water joint. Connect the hot water pipe and water outlet of water tank
with PPR pipe.
1.2 Matters Need Attention
The installation of unit must be in accordance with national and local safety codes.
Installation quality will directly affect the normal use of air conditioner unit. The user is
prohibited from installation by himself. Please contact your dealer after buying this machine.
Professional installation workers will provide installation and test services according to
installation manual.
Do not connect to power until all installation work is completed.
1.3 Dimension Data
1.3.1 Outdoor
GRS-CQ6.0Pd/Na-K(O),GRS-CQ8.0Pd/Na-k(O),GRS-CQ10Pd/Na-K(O)

GRS-CQ12Pd/Na-K(O),GRS-CQ14Pd/Na-K(O),GRS-CQ16Pd/Na-K(O)
GRS-CQ12Pd/Na-M(O),GRS-CQ14Pd/Na-M(O),GRS-CQ16Pd/Na-M(O)

AIR-TO-WATER HEAT PUMP

INSTALLATION

1.3.2 Indoor
GRS-CQ6.0Pd/Na-K(I),GRS-CQ8.0Pd/Na-k(I),GRS-CQ10Pd/Na-K(I),
GRS-CQ12Pd/Na-K(I),GRS-CQ14Pd/Na-K(I),GRS-CQ16Pd/Na-K(I),

AIR-TO-WATER HEAT PUMP

INSTALLATION

GRS-CQ12Pd/Na-M(I),GRS-CQ14Pd/Na-M(I),GRS-CQ16Pd/Na-M(I)

Install process of indoor unit

Step1Drilling hole on the wall in the following draw

AIR-TO-WATER HEAT PUMP

INSTALLATION

expansion bolt hole

unit outline

Step2Releasing screws, detach front cover from the indoor unit.

Step3Attaching indoor unit to the wall make use of accessory expansion bolt

AIR-TO-WATER HEAT PUMP

INSTALLATION

Expansion bolt

Install wall

C CAUTION!
While lifting the indoor unit, at least two persons should be joined. Weight of the
indoor unit is almost 52kg.
Precautions on Installation of Indoor Unit

Indoor unit shall be vertically mounted on the wall of the room with expansion bolt.

Keep the Indoor unit away from heat sources such as heat sink and so on in the room as
much as possible.

Keep the indoor unit as close as possible to outdoor unit. Level distance between
connection pipes can not exceed 30m and vertical distance can not exceed 15m.

1.3.3 Installation of Insulated Water Tank

AIR-TO-WATER HEAT PUMP

INSTALLATION

1.3.3.1 Installation Measure

The insulated water tank should be installed and keep levelly within 5m and vertically within
3m from the Indoor unit. It can be installed in the room.
Standing water tank must be installed vertically with the bottom on the ground, never
suspended. Installation place must be firm enough and the water tank should be fixed on the
wall with bolts to avoid vibration, as shown in the following figure. Weight capacity of water
tank during installation should also be considered.

Water tank
Fix
with
bolts
Installed on the ground and
never suspended

The minimum clearance from the water tank to combustible surface must be 500mm.
There should be water pipe, hot water joint and floor drain near the water tank in favor of
water replenishment, hot water supply and drainage of water tank.
Connection of inlet/outlet waterway: Connect the safety check valve attached with the unit
( points at insulated water tank) with the water inlet of water tank with PPR pipe according
to the following figure, sealing with unsintered tape. The other end of the safety check valve
should connect with tap water joint. Connect the hot water pipe and water outlet of water tank
with PPR pipe.

Safety check valve

Tap water

Note:
For safe use of water, water outlet/inlet of water tank must connect with a certain length of

AIR-TO-WATER HEAT PUMP

INSTALLATION

PPR pipe ,L 70R2cmR is inside radius of the pipe. Moreover, heat preservation should
be conducted and metal pipe can not be used. For the first use, water tank must be full of water
before the power is on.

Outline dimension and parameter of water tank

Litre

SXVD200LCJ/A-K
SXVD200LCJ/A-M
200L

SXVD200LCJ2/A-K
SXVD200LCJ2/A-M
200L

SXVD300LCJ/A-K
SXVD300LCJ/A-M
300L

SXVD300LCJ2/A-K
SXVD300LCJ2/A-M
300L

AIR-TO-WATER HEAT PUMP

coil
specification
coil
M
length
N
D(mm)
D1(mm)
H(mm)
A(mm)
B(mm)
C(mm)
E(mm)
F(mm)
I(mm)
J(mm)
K(mm)

INSTALLATION

SUS304 22X0.8
\
13m

10m
13m

\
18.5m

540
438
1595
272

10m
18.5m
620
528
1620
280

105
112
432
431
\
\

Outline
(DiameterH)

464
399
80
247.5

\
\

95
202.5

739

718

540X1595

620X1620

1620X625X630

1645X705X710

(mm)
Package
(W*D*H) (mm)
Net
kg
weight
Gross
kg
weight

68

71

82

87

77

80

92

97

Connection of Waterway System

If connection between water tank and indoor unit should be through the wall, drill a hole70
for pass of circulating water pipe. It is unnecessary if the hole is not needed.
Preparation of pipelines: Circulating water outlet/inlet pipe must be hot water pipe, PPR
pipe with nominal out diameter of dn25 and S2.5 series (wall thickness of 4.2mm) being
recommended. Cooling water inlet pipe and hot water outlet pipe of water tank should also
be hot water pipe, PPR pipe with nominal out diameter of dn20 and S2.5 series (wall
thickness of 3.4mm) being recommended. If other insulated pipes are adopted, refer to the
above dimensions for out diameter and wall thickness.
Installation of circulating water inlet/outlet pipes: Connect the water inlet of unit with
circulating outlet of water tank and water outlet of unit with circulating inlet of water tank.
Installation of water inlet/outlet pipes of water tank: Safety check valve ( on the valve
body points at water tank), filter and cut-off valve must be installed for water inlet pipe
according to the installation sketch of unit. At least a cut-off valve is needed for the water
outlet pipe.
Installation of blow-off pipe at the bottom of water tank: Connect a piece of PPR pipe
with drainage outlet to floor drain. A cut-off valve must be installed in the middle of the
drainage pipe and at the place where it is easy to be operated by the users.
After connection of all waterway pipelines, perform leakage test firstly (refer to debugging of
the unit). After that, bind up the water pipes, water temp sensor and wires with wrapping
tapes attached with the unit.

AIR-TO-WATER HEAT PUMP

INSTALLATION

Refer to Installation Sketch of Unit for details.

Indoor Unit

Other Thermal sensor (less than 5 meters)

Water Tank
Hot water output
Other
Thermal
System

Temp Sensor 1
Safety check
Filter
valve

Cool Water
Inlet

temp sensor 2

Tap water

Blow-off Outlet
Power cord of booster heater

Cut-off Valve

Joints Dimension
Description
Circulating water inlet/outlet of main unit

Joint pipe thread

1Male BSP

Cooling water inlet of water tank

1/2Female BSP

Circulating water inlet/outlet of water tank

3/4Female BSP

Hot water outlet of water tank

1/2Female BSP

Note:
Distance between main unit and insulated water tank should not exceed 5m levelly and
3m vertically. If higher, please contact with us. Water tank on lower and main unit on
higher side is recommended.
Prepare the materials according to the above joints dimension. If cut-off valve is installed
outside the room, PPR pipe is recommended to avoid freeze damage.
Waterway pipelines cant be installed until water heater unit is fixed. Do not let dust and
other sundries enter into pipeline system during installation of connection pipes.
After connection of all waterway pipelines, perform leakage test firstly. After that, perform
heat preservation of waterway system; meanwhile, pay more attention to valves and pipe
joints. Ensure enough thickness of insulated cotton. If necessary, install heating device
for pipeline to prevent the pipeline from freezing.
Hot water supplied from insulated water tank depends on pressure of water tap, so there
must be supply of tap water.
During using, the cut-off valve of cooling water inlet of water tank should be kept normally
on.
1.3.4 Electric Wiring
1.3.4.1 Wiring Principle
General principles

10

AIR-TO-WATER HEAT PUMP

INSTALLATION

Wires, equipment and connectors supplied for use on the site must be in compliance
with provisions of regulations and engineering requirements.
Only electricians holding qualification are allowed to perform wire connection on the site.
Before connection work is started, the power supply must be shut off.
Installer shall be responsible for any damage due to incorrect connection of the external
circuit of the unit.
Caution --- MUST use copper wires.
Connection of power cable to the electric cabinet of the unit
Power cables should be laid out through cabling trough, conduit tube or cable channel.
Power cables to be connected into the electric cabinet must be protected with rubber or
plastic to prevent scratch by edge of metal plate.
Power cables close to the electric cabinet of the unit must be fixed reliably to make the
power terminal in the cabinet free from an external force.
Power cable must be grounded reliably.
1.4 Installation Clearance Data

11

AIR-TO-WATER HEAT PUMP

INSTALLATION

(1). Water Volume and Pump capacity

12

AIR-TO-WATER HEAT PUMP

INSTALLATION

Note:
The water pump is three speed-adjustable(maximum/medium/minimum), In most case,
we strongly recommended to set speed as maximum;
If the noise of the pump is not acceptable, we recommended change the default speed to
medium speed, but to secure enough flow rate, do not set water speed as Min, it can
lead unexpected flow rate error EC;
(2). Water Volume and Expansion Vessel Pressure

Note:

13

AIR-TO-WATER HEAT PUMP

INSTALLATION

Expansion vessel is included which 10 liter and 1bar pre-pressure.

Total water volume of 280 liter is default; if total water is changed because of installation
condition, the pre-pressure should be adjusted to secure proper operation. If the indoor
unit is located at the highest position, adjustment is not required;
Minimum total water volume is 20 liter;
To adjust pre-pressure, use nitrogen gas by certificated installer;
The method of calculating the charging pressure of expansion vessel needed to be adjusted is as
follows.
During installation, if the volume of water system has changed, please check if the pre-set
pressure of the expansion vessel needs to be adjusted according to the following formula:

Pg ( H /10 0.3) Bar H ---the difference between installing location of indoor unit and
the highest spot of water system.
Ensure that the volume of water system is lower than the maximum volume required in the
above figure. If it exceeds the range, the expansion vessel does not meet the installing
requirement.
Installation height difference

Water volume

280L

7 m

Adjustment is not necessary

7 m

1. Pre-set pressure needs to be

adjusted according to the above
formula.
2. Check if the water volume is
lower than the maximum water
volume. (with help of the above
figure)

280L
1. Pre-set pressure needs to be
adjusted according to the above
formula.
2. Check if the water volume is
lower than the maximum water
volume. (with help of the above
figure)

The expansion vessel is too

small and adjustment is not
available.

Note
Installation height difference-the difference between installing location of indoor unit and

the highest spot of water systemif the indoor unit is located at the highest point of the
installationthe installation height difference is considered 0m
The minimum volume of the water system is 20 L.
Example 1The indoor unit is installed 5m below the outdoor unit and the total volume of the
water system is 100L.
Referring to the above figure, it is not necessary to adjust the pressure of the expansion
vessel.
Example 2 The indoor unit is installed on the highest spot of the water system and the total

14

AIR-TO-WATER HEAT PUMP

INSTALLATION

water volume is 350L.

As the volume of water system is higher than 280L, it is necessary to adjust the pressure
of the expansion vessel be lower.
The formula of calculating pressure

Pg ( H /10 0.3) (0 /10 0.3) 0.3 Bar

The maximum volume of the water system is about 410L. As the actual volume of the
water system is 350L, the expansion vessel meets the installing requirement.
Adjust the pre-set pressure of the expansion vessel from 1.0Bar to 0.3Bar.
Selection of expansion valve
Formula:
v=

ce
1 p1
1
1 p2

v --- Volume of expansion vessel

c --- Total water volume

p1 --- Pre-set pressure of expansion vessel

p2 -- The highest pressure during running of the system (that is the action pressure of safety
valve.)

e --- The expansion factor of water (the difference between the expansion factor of the
original water temperature and that of highest water temperature.)
Water expansion factor in different temperature
Expansion factor e
Temperature
0
0.00013
4
0
10
0.00027
20
0.00177
30
0.00435
40
0.00782
45
0.0099
50
0.0121
55
0.0145
60
0.0171
65
0.0198
70
0.0227
75
0.0258
80
0.029
85
0.0324
90
0.0359
95
0.0396
100
0.0434
3. Filling of Refrigerant
Before shipped out from manufacturer, the outdoor unit has been filled with refrigerant.

15

AIR-TO-WATER HEAT PUMP

INSTALLATION

Additional refrigerant may be filled when carrying out site connection of pipelines.
Check the liquid valve and the gas valve of the outdoor unit. The valves shall be completely
shut off.
Connect a vacuum pump to the liquid valve and the gas valve of the outdoor unit to remove
air from the inside of the indoor unit and the connecting pipe. Refer to the following figure:

Fig.22
After confirming that there is no leakage from the system, when the compressor is not in
operation charge additional R410A working fluid with specified amount to the unit through the
filling opening of the liquid pipe valve of the outdoor unit.

Be sure to charge the specified amount of refrigerant in liquid state to the liquid pipe
Since this refrigerant is a mixed refrigerant adding it in gas form may cause the
refrigerant composition to changepreventing normal operation.

Before chargingcheck whether the refrigerant cylinder is equipped with a siphon tube
or not

With siphon tube

No siphon tube

1.5 Connection of Pipeline

(1) Connection of Outlet Pipe for Indoor & Outdoor Unit
Align the expansion end of copper pipe with the center of threaded joint. Tighten the flaring
nuts with your hands.
Tighten the flaring nuts with torque wrench until you hear a click.
Bend of fitting pipe shall not be too low; otherwise the fitting pipe might crack. Please use
pipe bender when bending the fitting pipe.
When connecting outdoor and indoor unit, never pull the big and small joint of indoor unit
with force, so as to prevent the tubes of indoor unit from cracking and causing leakage.
Connecting pipe shall be supported by a rack without transmitting its weight to other units.

16

AIR-TO-WATER HEAT PUMP

INSTALLATION

(2) Installation of Protective Layer on Connection Pipe

To avoid condensate dew or water leakage on connecting pipe, the air pipe and liquid pipe
must be wrapped with heat preservation material and adhesive pipe for insulation from the
air.
The joints on indoor unit and outdoor unit must be wrapped with heat preservation materials
and have no clearance against the wall surface of indoor unit and outdoor unit.
Wrap the pipe with tapes.
1). Use the adhesive tape to wrap the connecting pipe and cable into one bundle. To prevent
condensate water from overflowing out of the drainpipe, the drainpipe shall be separated from
connecting pipe and cable.
2). Wrap the heat preservation tape so that each ring of tape shall press half of the previous
ring.
3). Fix the wrapped pipe onto the wall with pipe clamp.
4). Do not wrap the protective tape too tightly, as this will decrease the heat insulation
performance.
5). After completing the protection work and wrapping the pipe properly, close the wall holes
with sealing materials.

17

AIR-TO-WATER HEAT PUMP

model
GRS-CQ6.0Pd/Na-K
GRS-CQ8.0Pd/Na-K
GRS-CQ10Pd/Na-K
GRS-CQ12Pd/Na-K
GRS-CQ14Pd/Na-K
GRS-CQ16Pd/Na-K
GRS-CQ12Pd/Na-M
GRS-CQ14Pd/Na-M
GRS-CQ16Pd/Na-M

Pipe size
(Diameter:)
gas
Liquid
1/2"
1/4"
5/8"
3/8"
5/8"
3/8"
5/8"
3/8"
5/8"
3/8"
5/8"
3/8"
5/8"
3/8"
5/8"
3/8"
5/8"
3/8"

INSTALLATION

Length B
Standard
5.0m
7.5m
7.5m
7.5m
7.5m
7.5m
7.5m
7.5m
7.5m

Max.
20m
30m
30m
30m
30m
30m
30m
30m
30m

Elevation A
Standard
0m
0m
0m
0m
0m
0m
0m
0m
0m

Max.
10m
15m
15m
15m
15m
15m
15m
15m
15m

Additional
refrigerant
20g/m
50g/m
50g/m
50g/m
50g/m
50g/m
50g/m
50g/m
50g/m

Note:

18

AIR-TO-WATER HEAT PUMP

INSTALLATION

No additional charge of the refrigerant is need when the pipe length is less than 10 m (the
standard pipe length is 7.5m) , f the pipe length is longer than 10 m ,additional charge of the
refrigerant is needed according to the table.
Example: if 16kw model is installed at a distance of 25m, (25-10)*50=750g refrigerant should
be added;
Rated capacity is based on standard pipe length and maximum allowable length is base on
the product reliability in the operation.
Oil trap should be installed every 5-7 meters when the location of outdoor unit is higher than
indoor unit.

2 ELECTRIC WIRING WORK

2.1 Wiring Principle
(1).General principles

Wires, equipment and connectors supplied for use on the site must be in compliance
with provisions of regulations and engineering requirements.

Only electricians holding qualification are allowed to perform wire connection on the site.

Before connection work is started, the power supply must be shut off.

Installer shall be responsible for any damage due to incorrect connection of the external
circuit of the unit.

Caution --- MUST use copper wires.

(2). Connection of power cable to the electric cabinet of the unit

Power cables should be laid out through cabling trough, conduit tube or cable channel.

Power cables to be connected into the electric cabinet must be protected with rubber or
plastic to prevent scratch by edge of metal plate.

Power cables close to the electric cabinet of the unit must be fixed reliably to make the
power terminal in the cabinet free from an external force.

Power cable must be grounded reliably.

2.2 PCB Outline

(1). GRS-CQ6.0Pd/Na-K(O).GRS-CQ8.0Pd/Na-K(O).GRS-CQ10Pd/Na-K(O)

19

AIR-TO-WATER HEAT PUMP

INSTALLATION

Silk Screen

Specification

AC-L
N
E1

Live wire input of power supply, red

Neutral wire input of power supply, white
Ground wire, yellow green

L2-2
L1-1
L2-1
L1-2
U
V
W

PFC blue inductive wire

PFC brown inductive wire
PFC yellow inductive wire
PFC white inductive wire
U-phase of compressor
V-phase of compressor
W-phase of compressor
DC fan
1 pinstrong power supply3 pinfan GND4 pin+15V5 pincontrol signal6 pin
feedback signal;
4-way valve
Electric heating tape
E-heater of chassis
High pressure switch

DC_MOTOR1
4V 4V1
HEAT
VA-1
HPP
LPP
OVC-COMP
T-SENSOR2
TSENSOR3
CN66.CN67
CN65
FA
H-PRESS

Low pressure switch

Overload protection of compressor
1, 2 holepipe temperature3, 4 holeenvironment5, 6 holeexhaust
1 hole: +3.3V 2 hole: detection ; suction temperature sensor
Communication cable 2 pin B3pinA
Communication cable: 1 pin earthed2 pin B3 pin A4 pin+12power supply;
It can not be used for communication between outdoor unit and indoor unit;
Pipe electric expansion valve
1-4 pindriving impulse output5 pin+12V
Signal input of pressure sensor
1 pinGND2 pinsignal input3 pin+5V

(2). GRS-CQ12Pd/Na-K(O).GRS-CQ14Pd/Na-K(O).GRS-CQ16Pd/Na-K(O)

20

AIR-TO-WATER HEAT PUMP

Silk Screen
AC-L
N
L1-1

INSTALLATION

L2-1

Specification
Live wire input of power supply, red
Neutral line input of power supplyPFC blue inductive wire blue
PFC brown inductive wire
PFC yellow inductive wire

L1-2

PFC white inductive wire

U-phase of compressor

V-phase of compressor

W-phase of compressor

DC_MOTOR1

DC_MOTOR2
4V1
HEAT
VA-1
HPP
LPP
T-SENSOR2
TSENSOR3
CN66.CN67
CN65
FA
H-PRESS

DC fan
1 pinstrong power supply3 pinfan GND4 pin+15V5 pincontrol
signal6 pinfeedback signal
DC fan
1 pinstrong power supply3 pinfan GND4 pin+15V5 pincontrol
signal6 pinfeedback signal
4-way valve
Electric heating tape
E-heater of chassis
High pressure switch
Low pressure switch
1, 2holepipe temperature3, 4holeenvironment5, 6holeexhaust
1 hole:+3.3V 2 hole: detection: suction temperature sensor
Communication cable 2 pin B3 pin A
Communication cable 1 pin earthed2 pin B3 pin A4 pin+12 power supply
It can not be used for communication between outdoor unit and indoor unit.
Pipe electric expansion valve
1-4 pindriving impulse output5 pin+12V
Signal input of pressure sensor
1 pinGND2 pinsignal input3 pin+5V

(3). GRS-CQ12Pd/Na-M(O).GRS-CQ14Pd/Na-M(O).GRS-CQ16Pd/Na-M(O)

21

AIR-TO-WATER HEAT PUMP

INSTALLATION

silk screen
L1

specification

L2

live wire input of power supply

L3
N

Neutral line input of power supply

Reactor red inductive wire

U-phase of compressor

V-phase of compressor

W-phase of compressor

4V1

DC fan
1 pinstrong power supply3 pinfan GND4
pin+15V5 pincontrol signal6 pinfeedback signal
DC fan
1 pinstrong power supply3 pinfan GND4
pin+15V5 pincontrol signal6 pinfeedback signal
4-way valve

HEAT

electric heating tape

VA-1
HPP

e-heater of chassis
high pressure switch

LPP

low pressure switch

1, 2holepipe temperature3,
6holeexhaust

DC_MOTOR1

DC_MOTOR2

T-SENSOR2

4holeenvironment5,

TSENSOR3

1 hole:+3.3V 2 hole: detection: suction temperature sensor

CN66, CN67

communication cable 2 pin B3 pin A

CN65

FA
H-PRESS

communication cable 1 pin earthed2 pin B3 pin A4

pin+12 power supply
It can not be used for communication between outdoor unit
and indoor unit.
pipe electric expansion valve
1-4 pindriving impulse output5 pin+12V
signal input of pressure sensor
1 pinGND2 pinsignal input3 pin+5V

(4). GRS-CQ6.0Pd/Na-K(I).GRS-CQ8.0Pd/Na-K(I).GRS-CQ10Pd/Na-K(I). GRS-CQ12Pd/NaK(I).GRS-CQ14Pd/Na-K(I).GRS-CQ16Pd/Na-K(I)

22

AIR-TO-WATER HEAT PUMP

INSTALLATION

GRS-CQ12Pd/Na-M(I).GRS-CQ14Pd/Na-M(I).GRS-CQ16Pd/Na-M(I)
HEAT2-L

RUN

HEAT1-L

PUMP2
AC_L N

HEAT3-L

PUMP1

2V1_OFF
ERR

2V1_ON

2V2_OFF
2V2_ON

3V1_OFF
3V1_ON

3V2_OFF
3V2_ON
LED1
LED2
LED3

CN30
T-SENSOR1
CN31

T-SENSOR2
T-SENSOR3
T-SENSOR4
T-SENSOR5
T-SENSOR6

TR-IN

TR-OUT1

Silk Screen
AC-L
N
PUMP1
PUMP2
RUN
HEAT3-L
HEAT1-L
HEAT2-L
ERR
2V1_OFF
2V1_ON
2V2_OFF
2V2_ON
3V1_OFF
3V1_ON
3V2_OFF
3V2_ON
T-SENSOR1
T-SENSOR2
T-SENSOR3
T-SENSOR4
T-SENSOR5
T-SENSOR6
DOOR-C
OVC-HEAT3
OVC-HEAT1
OVC-HEAT2
IN-SW
COM-MANUAL
COM-OUT
COM-BMS
TR-OUT1
TR-OUT2
TR-IN
CN30
CN31

TR-OUT2

COM-MANUAL
OVC-HEAT1
IN-SW
COM-OUT
OVC-HEAT2

COM-BMS

Location
X13
X14
X15
X16
X17
X18
X19
X5
X6
X7
X8
X9
X10
X11
X12
CN10
CN11
CN12
CN13
CN14
CN15
CN23
CN28
CN26
CN27
CN25
CN6
CN5
CN7
CN2
CN3
CN1
CN30
CN31

OVC-HEAT3

DOOR-C

Specification
live wire of power supply
Neutral wire of power supply
live wire of indoor water pump
live wire of solar water pump
running indicator
e-heater of water tank
e-heater of indoor unit 1
e-heater of indoor unit 2
error indicator
Electric magnetic 2-way valve1 is normally closed.
Electric magnetic 2-way valve1 is normally open.
Electric magnetic 2-way valve2 is normally closed.
Electric magnetic 2-way valve2 is normally open.
Electric magnetic 3-way valve1 is normally closed.
Electric magnetic 3-way valve1 is normally open.
Electric magnetic 3-way valve2 is normally closed.
Electric magnetic 3-way valve2 is normally open.
terminal of temperature sensor1
terminal of temperature sensor2
terminal of temperature sensor3
terminal of temperature sensor4
terminal of temperature sensor5
terminal of temperature sensor6
Door detection input
e-heater of water tank adhesion-proof protection detector
e-heater of indoor unit1 adhesion-proof protection detector
e-heater of indoor unit2 adhesion-proof protection detector
detection input of water flow switch
connect the wired controller
connect to outdoor unit
Building Management System (BMS)
transformer output 1
transformer output 2
220V in put of transformer
heavy-current interface of end controller
heavy-current interface of end controller

2.3 Electric Wiring Design

2.3.1 Wiring Diagram: Indoor Unit
GRS-CQ6.0Pd/Na-K(I),GRS-CQ8.0Pd/Na-K(I),GRS-CQ10Pd/Na-K(I),GRS-CQ12Pd/Na-K(I)

23

AIR-TO-WATER HEAT PUMP

INSTALLATION

,GRS-CQ14Pd/Na-K(I),GRS-CQ16Pd/Na-K(I):
Indoor Unit

POWER

L
N
1

N(2)

2-way
valve1

XT1

2-way
valve2
Specification:
1 If there is gate control function,
pull out the leading wire 50 on
terminal boards between19 and 20
and then connect the
Gate-controller
XT2 20 19

3-way
valve1
3-way
valve2

XT2 20 19

AP

Running
indicating lamp
Error
indicating lamp

50
Gate-controller

2 The wires in the imaninal frames

are connected by the consumer.
3 power supply for Thermostat:If it
is 230V AC,please connect Terminal
block(xt3) 21.22.23.24;If it is 24V
AC, please connect Terminal
block(xt3) 25.26.27.28.
Communication line

PC
Long-distance
Monitor PC

Display
board

GRS-CQ12Pd/Na-M(I), GRS-CQ14Pd/Na-M(I), GRS-CQ16Pd/Na-M(I):

PE

Indoor Unit

PE

POWER

XT1
XT3

2-way
valve1
2-way
valve2
3-way
valve1

PE

Specification:
1. If the gate control function is required,
pull out the leading wire 50 between
terminal 19 and 20 on the terminal block
and then install the gate-controller.

XT2 20 19

3-way
valve2

Running
indicating lamp

AP

PE

Error
indicating lamp

XT2 20 19

50

2. The wires in broken line should be

connected by the client.
3 Power supply for thermostat: If it
is 230V AC,please connect the
thermostat to the terminal block(xt3)
21.22.23.24;If it is 24V AC, please
connect the termostat to the terminal
block(xt3) 25.26.27.28.

Communication line

OUTDOOR
UNIT AP1

PC
Display
board

Long-distance
Monitor PC

2.3.2 Wiring Diagram: Outdoor Unit

GRS-CQ6.0Pd/Na-K(O),GRS-CQ8.0Pd/Na-K(O),GRS-CQ10Pd/Na-K(O):

24

AIR-TO-WATER HEAT PUMP

INSTALLATION

GRS-CQ12Pd/Na-K(O),GRS-CQ14Pd/Na-K(O),GRS-CQ16Pd/Na-K(O):

GRS-CQ12Pd/Na-M(O), GRS-CQ14Pd/Na-M(O), GRS-CQ16Pd/Na-M(O):

25

AIR-TO-WATER HEAT PUMP

INSTALLATION

2.3.3 Wiring Diagram: Water Tank

SXVD200LCJ/A-K, SXVD200LCJ2/A-K, SXVD300LCJ/A-K, SXVD300LCJ2/A-K:

26

AIR-TO-WATER HEAT PUMP

INSTALLATION

SXVD200LCJ/A-M, SXVD200LCJ2/A-M, SXVD300LCJ/A-M, SXVD300LCJ2/A-M:

Thermostat1 Thermostat2

WP95A-R

PE

PE

(WP85A-R)

PE

Heater

PE

27

PE

Water tank

Water-tank
temp sensor1

Display
board

CN16

Main Baord

AP
Outdoor
Unit

CN5

Remote air
temp sensor

CN14

Thermostat

Long-distance
monitor PC

CN7

Thermostat

XT2

20 19
Gate-controller

If there is gate control function,

pull out the leading wire 50 on
terminal board XT2)between19 and
20 and then connect the Gate-controller

Specification:
1 Running indicating lamp(HL1) and Error indicating lamp (HL2) are connected or not on the basis of the
clients'demand.
2 Client water pump AC contactor(KM4) is back-up Pump for the future , so it is not be connect;
3 Leakage SwitchLK is necessary for additional installation, Please reference to
page 10 4.3 Electrical Data

POWER
230V 50HZ

LK

XT1
L N 1 N(2)

3-way
valve2

Error
indicating lamp

PE

3-way
valve1

Inside Unit
Electric Box

2-way
valve2

Water-tank
temp sensor2

2-way
valve1

Running
indicating lamp

Other thermal system

Water- out temp sensor

Power supply for Thermostat:If it is 230V AC,please

connect Terminal block(xt3) 21.22.23.24;If it is 24V
AC, please connect Terminal block(xt3) 25.26.27.28.
They are can not be connected as the same time.

AIR-TO-WATER HEAT PUMP

INSTALLATION

Wiring Diagram: Indoor and Outdoor Unit (Including Field Wiring)

GRS-CQ6.0Pd/Na-K, GRS-CQ8.0Pd/Na-K, GRS-CQ10Pd/Na-K, GRS-CQ12Pd/Na-K, GRSCQ14Pd/Na-K, GRS-CQ16Pd/Na-K:

28

PE

LK

XT2

3-way
valve2

Water tank

PE

BKBN BU YEGN

29 30 31

PE

3-way
valve1

Inside Unit
Electric Box

2-way
valve2

Water-tank
temp sensor1

Display
board

CN16

Main Baord

AP
Outdoor
Unit

CN5

Remote air
temp sensor

CN14

Thermostat

Long-distance
monitor PC

CN7

Thermostat

XT2

20 19
Gate-controller

If there is gate control function,

pull out the leading wire 50 on
terminal board XT2)between19 and
20 and then connect the Gate-controller

Specification:
1 Running indicating lamp(HL1) and Error indicating lamp (HL2) are connected or not on the basis of the
clients'demand.
2 Client water pump AC contactor(KM4) is back-up Pump for the future , so it is not be connect;
3 Leakage SwitchLK is necessary for additional installation, Please reference to
page 10 4.3 Electrical Data

POWER
380 415V-3Ph-50Hz

L1 L2 L3 N

L1 L2 L3 N

XT1

2-way
valve1

Error
indicating lamp

Water-tank
temp sensor2

Running
indicating lamp

Other thermal system

Water- out temp sensor

Power supply for Thermostat:If it is 230V AC,please

connect Terminal block(xt3) 21.22.23.24;If it is 24V
AC, please connect Terminal block(xt3) 25.26.27.28.
They are can not be connected as the same time.

AIR-TO-WATER HEAT PUMP

INSTALLATION

GRS-CQ12Pd/Na-M, GRS-CQ14Pd/Na-M, GRS-CQ16Pd/Na-M:

2.3.5 Terminal Board Information

29

AIR-TO-WATER HEAT PUMP

INSTALLATION

GRS-CQ6.0Pd/Na-K, GRS-CQ8.0Pd/Na-K, GRS-CQ10Pd/Na-K,

GRS-CQ12Pd/Na-K, GRS-CQ14Pd/Na-K, GRS-CQ16Pd/Na-K

Terminal board 3

21 22 23 24 25 26 27 28

Thermostat(1)

Thermostat(2)

Terminal Board 1
power supply for Water
tank electric heater
1

10

11

12

13

14

15

16

17

18

19

20

N(2)

Connecting external electric

power supply for Indoor Unit

Connection for
Indicating lihgt

Gate Control Fuction

Terminal Board 2
1

2 way value(1)

2 way value(2)

3 way value(1)

9 10

11 12 13 14 15 16 17 18 19 20

3 way value(2) Connection for Client

water's AC contactor

Connection for
Accident lihgt

GRS-CQ12Pd/Na-M, GRS-CQ14Pd/Na-M, GRS-CQ16Pd/Na-M:

30

AIR-TO-WATER HEAT PUMP

INSTALLATION

Terminal Board 2
Connection for
Indicating lihgt

2 way value(1)

2 way value(2)

9 10

11 12 13 14 15 16 17 18 19 20

3 way value(2) Connection for Client

water's AC contactor

3 way value(1)

Gate Control Fuction

Connection for
Accident lihgt

Terminal Board 1

L1 L2 L3 N
Connecting external electric
power supply for Indoor Unit

Terminal board 3

21 22 23

24

25

Thermostat(1)

1.3.6

26 27

Thermostat(2)

28

29 30

31

power supply for

water tank eletric
heater

Connecting with External Electric

31

AIR-TO-WATER HEAT PUMP

INSTALLATION

GRS-CQ6.0Pd/Na-K, GRS-CQ8.0Pd/Na-K, GRS-CQ10Pd/Na-K,

GRS-CQ12Pd/Na-K, GRS-CQ14Pd/Na-K, GRS-CQ16Pd/Na-K

Water Tank

CN15
CN14
CN13
CN12
CN11
CN10

10

11

12

13

14

15

16

17

18

19

20

Water -Tank
Temp Sensor1

N(2)

Water -Tank
Temp Sensor2
N

L
External Power Supply
(230V 50Hz AC)

GRS-CQ12Pd/Na-M, GRS-CQ14Pd/Na-M, GRS-CQ16Pd/Na-M

32

AIR-TO-WATER HEAT PUMP

INSTALLATION

Water Tank

CN15
CN14
CN13
CN12
CN11
CN10

10

11

12

13

14

15

16

17

18

19

20

Water -Tank
Temp Sensor1
L1

L2

L3

Water -Tank
Temp Sensor2
L3
L2
L1

External Power Supply

(380-415V 50Hz 3N )

2.3.7 2-Way Valve

2-way valve is required to control water flow while cooling operation. Role of 2way valve is to
cut off

water flow into under floor loop in cooling mode when fan coil unit is equipped for cooling

operation.
General Information
Type

NO 2-wire

NC 2-wire

Power

Operating Mode

Supported

230V 50Hz

Closing water flow

Yes

AC

Opening water flow

Yes

230V 50Hz

Closing water flow

Yes

AC

Opening water flow

Yes

(1) : Normal Open type. When electric power is NOT supplied, the valve is open. (When electric power is
supplied, the valve is closed.)
(2) : Normal Closed type. When electric power is NOT supplied, the valve is closed. (When electric power is

33

AIR-TO-WATER HEAT PUMP

INSTALLATION

supplied, the valve is open.)

How to Wire 2-Way Valve

Follow below procedures Step 1 ~ Step 2.
Step 1. Uncover front cover of the indoor unit and open the control box.
Step 2. Find terminal block and connect wire as below.

OFF

ON

OFF

NC

NO

NC

2 way value 1

5
ON
NO

6
N
N

2 way value 2

Normal Open type should be connected to wire (NO) and wire (N)for valve closing in cooling mode.
Normal Closed type should be connected to wire (NC) and wire (N)for valve closing in cooling mod
(NO) : Line signal (for Normal Open type) from PCB to 2way valve
(NC) : Line signal (for Normal Closed type) from PCB to 2way valve
(N) : Neutral signal from PCB to 2way valve

2.3.8 3-Way Valve

3way valve is required to operate sanitary water tank. Role of 3way valve is flow switching
between under floor heating loop and water tank heating loop.

General Information
Type

Power

Selecting Flow A between

SPDT
3-wire

Operating Mode

230V 50Hz AC

Flow A and Flow B

Selecting Flow B between
Flow B and Flow A

Supported
Yes

Yes

(1) : SPDT = Single Pole Double Throw. Three wires consist of Live1 (for selecting (for selecting Flow B), and
Neutral (for common).
(2) : Flow A means water flow from the indoor unit to under floor water circuit.
(3) : Flow B means water flow from the indoor unit to sanitary water tank.
How to Wire 3Way Valve
Follow below procedures Step 1 ~ Step 2.
Step 1. Uncover front cover of the indoor unit and open the control box.
Step 2. Find terminal block and connect wire as below.

34

AIR-TO-WATER HEAT PUMP

INSTALLATION

7
OFF

8
ON

9 10
N

OFF

3 way value 1

11 12
ON

3 way value 2

3way valve should select water tank loop when electric power is supplied to wire (OFF) and wire (N).
3way valve should select under floor loop when electric power is supplied to wire (ON) and wire (N).
(OFF) : Line signal (Water tank heating) from PCB to 3way valve
(ON) : Line signal (Under floor heating) from PCB to 3way valve
(N) : Neutral signal from PCB to 3way valve

2.3.9 Gate-controller
If there is gate control function, pull out the leading wire 50 on terminal boardXT2
between19 and 20 and then connect the Gate-controller
Installation Guide follow as:

XT2

20 19

XT2 20 19
Gate-controller

50

GREE does not supply

this section

2.3.10 Remote Air Temperature Sensor

Front side

Back side

35

AIR-TO-WATER HEAT PUMP

INSTALLATION

Remote Air Temperature Sensor

NO
YES

1.5 Meters

NO

NO NO

Doors

Note:
Distance between the indoor unit and the remote air temperature senor should be less
than 15 meter due to length of the connection cable of remote air temperature sensor.
Height from floor is approximately 1.5 meter;
Remote air temperature sensor can not be located where the area may be hidden when
door is open;
Remote air temperature sensor can not be located where external thermal influence may
be applied;
Remote air temperature sensor should be installed where space heating is mainly
applied;
Installation Guide follow as:

Remote Air Environment

Temp sensor

CN15

PCB

Electric box

36

AIR-TO-WATER HEAT PUMP

INSTALLATION

Thermostat:

22 23 24

21

XT3

Cool

Heat

L
(230V)

25 26 27
Cool

Heat

28

L
(24V)

Fig 1
XT3

22 23 24

21

Heat

L
(230V)

25 26 27
Heat

28

L
(24V)

Fig 2
(L) : Live signal from PCB to thermostat
(N): Neutral signal from PCB to thermostat
How to Wire Thermostat

Uncover the front cover of the indoor unit and open the control box
Identify the power specification of the thermostatif it is 230V find terminal block
XT3 as NO.2124; Otherwiseif it is 24Vfind terminal blockXT3 as NO.2528;
If it is Heating/Cooling thermostat please connect wire as Fig 1
If it is Heating only thermostat please connect wire as Fig 2

1)

NEVER USE 230V AC and 24V AC Thermostat at the same time, otherwise, it will cause
short-circuit and power cut-off by circuit breaker;

2)

setting temperature by Thermostat(heating or cooling) should be chosen within the setting

temperature range of the product ;

3)

For other constrains, please refer to previous page where constrains about

4)

Remote air temperature sensor

5)

Do not connect external electric loads, Wire (L) and (N) should be used only for
operation Electric type thermostat.

6)

Never connect external electric loads such as valves, fan coil units, etc. If connected, PCB of
the indoor unit can be seriously damaged

7)

Installation of Thermostat is very similar to that of Remote air temperature sensor,

Thermostat

Thermostat is generally used to control the product by air temperature. When thermostat is
connected to the product, the product operation is controlled by the thermostat.

37