CONTENTS

ANNEXURES
1. ANNEXURE-I :
2. ANNEXURE-II:
3. ANNEXURE-III:
4. ANNEXURE-IV:
5. ANNEXURE-V:
6. ANNEXURE-VI:
7. ANNEXURE-VII:
8. ANNEXURE-VIII:
9. ANNEXURE-IX:

SYMBOLS AND LEGENDS

GENERAL NOTES
INSTRUMENT TAGGING
USAGE OF BLOCK AND BLEED VALVES
DESUPERHEATING
CONTROL VALVE/ON-OFF VALVE FAIL ACTION
INSTRUMENT PROCESS CONNECTION SIZES
SPECIAL NOTES ON INSTRUMENTATION
PIPE TAGGING

PREFACE
The intent of this write-up is to provide a simplistic guidelines for preparing a Piping
and Instrumentation Drawing (P&ID). I felt the necessity to summarize these
guidelines hoping it may assist the young engineer with a kick start in Engineering.
Although P&IDs are basically meant and respected by he Process, Mechanical and
Instrumentation discipline, it will may also provide a guide for the others like the
Electrical discipline to understand and maybe appreciate the document which is
after all the mother document for the process plant under consideration. I call it
simplistic because it may not cover all the aspects of P&IDs of more complex plants
like the petrochemical or refineries, where the process requirements and variety of
fluids are multifarious.
In these few pages I have tried to capture the basic philosophy, extent of detailing,
instrumentation requirements and valving philosophy of a typical plant involving
basically steam and water like a power plant.

1. WHAT IS A P&ID?
a. It is basically a drawing which is based on the Process Flow Diagram
(PFD) and depicts the technical realization thereof by means of
graphical symbols, lines together with symbols for process
instrumentation and control functions.
2. WHAT ARE VARIOUS STAGES OF USAGE OF A P&ID (LIFE CYCLE)
a. Preparatory Step: This step is the step of gathering and collating the
information and freezing the design philosophy that maybe required to
develop the P&ID. This document can be used a and example of the
design philosophy. The basic document is Process Flow Diagram to
start with. In this step, the nameplate, symbology, piping specification,
HAZOP study (if applicable), Cause and Effect study, precommissioning issues, shut down issues. All the above activities
initiate from the PFD and the process description.
b. Preparation:The first cut of the P&ID shall contain the minimum
thefollowing information :i. Equipment number, name and type of Equipment.
ii. Piping size, piping number, packages identified, drains and vents
and their destination.
iii. Instrument type, tag number, control valve failure action.
iv. Control signal lines

3. WHAT
a.
b.
c.

ARE THE STANDARDS OF REFERENCE?

ASME (American Society for Mechanical Engineers)
ANSI (American National Standards Institute)
ISA (International Society for Automation)

The above standardization bodies have various standards which are

followed and is listed in ANNEXURE-A. In addition to these standards, the
graphical symbols maybe customized by the Company and adopted as a
standard. In any case, all symbols and conventions followed should be
listed as the first sheet (Legend Sheet) and this will supersede any of the
afore mentioned standards.
4. UNITS

The units used in our P & IDd do not fall into a specific standard like Imperial,
SI or MKS. The units
PARAMETERS
UNITS
used
are
more
LENGTH
mm
utilitarian In the sense
TIME
secs
that these units are
GAS PRESSURE
mmwcl
more commonly used
STEAM PRESSURE
kg/cm2g
TEMPERATURE
Celsius
in the power industry
FLOW
Tonne/hr
and is a mixture of the
(STEAM/GAS)
conventional standards.
VISCOSITY
2
The Table-1 below gives
FLOW (LIQUID)
m3/hr
the units that are
SPECIFIC WEIGHT
m3/kg
used:-

TABLE-1G

5. REPRESENTATION AND LAYOUT

The following conventions should be followed as far as practicable:a. Flow of fluids/solids should be from left to right. Flow direction should
be shown by arrows.
b. Relative positions of the equipment should be representative (i.e., BFP
should not be shown above the Dearator)
c. The sizes of the equipment shall also be representative and
proportional to the actual equipment. (e.g. the integral bypass MOV
shall be shown as smaller than the main MOV)
d. The symbology shall be followed as per the LEGEND sheet (Refer
ANNEXURES)
e. Line thickness shall be representative of the line size and importance
(e.g in the STEAM Distribution drawing, the line other than steam lines
should be thinner than the steam lines. The drain/vent lines should
always be thinner than the main lines).
f. Process parameter flagging and equipment details shall be covered
later in this write-up.
6. GUIDELINES FOR DRAFTING
The following conventions should be followed as far as practicable for
drafting:a. Drafting must be such quality and density that the drawing when
reduced to A3 should be clearly legible.
b. The basic drawing shall be A0 (1189X849 mm), A1 (591X841 mm), A2
(420 X 594mm) or A3 (297 X 420 mm) depending on the density.
c. The sizes of the equipment shall also be representative and
proportional to the actual equipment. (e.g. the integral bypass MOV

shall be shown as smaller than the main MOV). BFP should be larger
than the discharge MOV and smaller than the Dearator.
d. The symbology shall be followed as per the LEGEND sheet (Refer
ANNEXURES)
e. Line thickness shall be representative of the line size and importance
(e.g in the STEAM Distribution drawing, the line other than steam lines
should be thinner than the steam lines. The drain lines should always
be thinner than the main lines).
7. HOW TO DRAW THE TITLE BLOCK
Following information should be there in the Title Block
a.
b.
c.
d.
e.
f.

Companys name (Thermax Ltd. With Division) & Logo

End-user (Clients Name) and Logo
Clients Consultants name and Logo
Drawing Title with Project Number
Drawing Number with sheet number
Revision Table

The Size of the Title Block shall be generally as per the following guidelines:-

TABLE-2G
Drawing Size
A0
A1
A2
A3

Size of Title Block Inc Rev Table W(mm)XH(mm)

180X190
130X175
100X155
75X120

LINE WIDTHS
Following ,line widths maybe used as guideline
Main Process Line = 0.8 mm
Secondary Process lines, utility lines = 0.5 mm
Drains/Vents = 0.4 mm
Machinery and Equipment symbols = 0.5 mm
Valves and fittings = 0.4 mm
Instrumentation/Electrical signals line = 0.3 mm
Instrumentation symbols = 0.4 mm
Process Value Boxes =0.4 mm
FONT SIZES

Drawing Title Block (All in

-

Drawing

Clients Name

Consultants

Drawing Title

A0

A1

A2

A3

caps)
Number :

A0

A1

A2

A3

A0

A1

A2

A3

A0

A1

A2

A3

Name

Process Values :
Equipment Name:
Line Numbers:
Instruments tags:

MINIMUM INFORMATION TO BE PROVIDED IN P&ID

1. P&IDs shall contain the information as detailed below. Some of the
information as called for may not be available during the basic design which
will be gradually filled/updated during detailed engineering phase.
2. Vendor supplied packages shall be shown boxed up in dotted lines with title
and name of the package vendor. Vendor Drawing References may be added
in the notes.
3. Following lines shall be shown in P&ID:a. Process lines/ducts
b. Utility lines
c. Drains and Vent lines
d. Instrument signal lines
4. Following equipments shall be shown in the P&ID:a. Tanks, Vessels, Heaters, Coolers
b. Instruments
c. Valves and dampers
5. Identification:
a. Process/Utility lines
i. Process lines/utility lines shall be identified by a designation
Following is an example of line designation/numbering. Refer
ANNEXURE-iX for coding.
XXX-YYY -ZZZ-UUU-VV-WW
INSULATION THICKNESS (mm)
COLD/HOT/PERSONNEL/NIL
PIPE SPECIFICATION
SERIAL
NUMBER

NOMINAL BORE DIA (mm)

FLUID CODE

The information related to the process parameters shall be shown for

all process and utility lines with a flag as shown below:-

MAX

NORM

MIN

P (ata)
T (deg
C)
F
(TPH)
6. Equipment Details to be shown:a. TANKS & VESSELS
i.
ii.
iii.
iv.
v.
vi.
vii.

viii.
ix.
x.

Height and diameter

Volume
Design Pressure and Temperature
All Nozzles, manholes, Safety Relief Valves, draw out and inlet,
drains/vents
Instrument standpipes with details (wherever required)
Equipment Number and Name
Position of NWL (normal Working Level), LLL (low Liquid level),
LLLL(Low-Low Liquid Level), HLL (High Liquid level), HHLL(HighHigh Liquid Level). LLLL, HHLL needs to be shown only when
interlocks and alarms are involved.
Water drop-out boots
Bottom Elevation
Skirt height (if applicable)

Notes:
a) A PG and TG to be provided, in general
b) Relief valve to be provided on the top in case of pressurized vessel
c) Flame arrestor maybe required depending on the nature of the
liquid.
d) Blinded nozzles also need to be shown
e) Nozzle identification number to be provided.
b. HEAT EXCHANGERS/COOLERS
i. Same as TANKS& VESSELS
ii. Spectacle-blinds for isolation if required
iii. PG and TG to provided at inlet and outlet of shell and tube side

iv. Isolation and bypass valve to be provided for maintenance.

v. Bottom Elevation
vi. Skirt height (if applicable)
a. A PG and TG to be provided, in general for the shell
b. Relief valve to be provided on the top in case of pressurized vessel
c. Flame arrestor maybe required depending on the nature of the
liquid.
d. Blinded nozzles also need to be shown
e. Nozzle identification number to be provided.
c. PUMPS
i.
ii.
iii.
iv.

Type of Pump, Capacity, operating head

All nozzles including instrument connections
Duty (1W+1S) etc.
Suction valves, strainer, check valve, PG at discharge, discharge
isolation valve. PG should be installed between the discharge and
the check valve.
v. Auxiliary connection-cooling water, lube oils etc.
vi. Warm-up lines
vii. Pressure relief valve (is applicable)
d. COMPRESSORS/BLOWERS
i. Type of compressor/blower
ii. Capacity (Nm3/Hr), suction and discharge pressure & temperature
iii. Start-up facilities (cooling water etc.)
iv. Suction strainer
v. Suction and discharge valves
vi. Lube oil and sealing systems (if required externally)
vii. Inter-stage and after-coolers
viii. Surge Protection (if required)
ix. Inlet/Outlet nozzles
x. All non-skid instruments. (Skid mounted instruments to be shown
in Compressor P&ID)
e. STEAM TURBINES
i. All nozzles and connections
ii. All Instruments mounted on the casing
iii. QCNRV in bleed lines
iv. Drain pots and condensate recovery system
v. Warm and vent lines
vi. Safety relief Valves

ANNEXURE-IV
USAGE OF BLOCK AND BLEED VALVES
Block and bypass valve arrangement is generally provided for process lines
that cannot be shutdown for maintenance of a control valve or an
instrument, strainer etc.
Bypass valves are not necessary in the following cases:1. Where it is desirable to reduce the leakages. Because more the line
devices, more the chances of leakage.
2. Wherever shutting down the line will not cause safety or operability
issues.
3. Pressure self-regulating valves
4. Lines used for temporary services
5. Shut off valves.
6. Around 3-way valves
Bypass valves are necessary and should be provided in the following cases:1. Wherever continuous operation of control valve is required.
Block valves
1. Provide inlet block valve unless the upstream line can be shutdown
2. Provide outlet block valve unless the downstream line can be shut
down.
3. Provide drain/vent valve (at least gate) between inlet block and
control valve.
4. Provide drain/vent valve (at least gate) between outlet block and
control valve in case the fluid is corrosive/toxic or it is shut down valve.
Sizes of BLOCK and BYPASS VALVES
1. BLOCK VALVES shall be provided generally on both sides of a control
valve, and the sizes shall be line size gate valves/ball valves.
2. BYPASS VALVES shall be generally globe type one size larger than the
control valve or line size. For line size more than 4, gate valve maybe
provided considering cost.

ANNEXURE-VIII
SPECIAL NOTES ON INSTRUMENTATION
Instruments must be provided wherever necessary and shall be avoided which
cannot be justified. Existence of each instrument or a measuring point should be
justifiable by either:i)
ii)
iii)
iv)
v)
vi)
vii)

Requirement of the operator (either in field or CCR)

Requirement for performance assessment of process or equipment
Required for Alarm
Required for control , interlock and protection.
Called for by HAZOP analysis
Mandated by Statutory regulations (like IBR, ASME, CPCB, EPA etc.)
Recommended by accepted Industry Standards (like ASME PTC codes,
etc)

Over instrumentation is as bad or worse than under-instrumentation. The extent of

instrumentation should be mainly guided by the above requirements, together with
cost-considerations. Since the type of instruments are also depicted in the P & ID, it
is while making the P&ID these are to be decided. The following guidelines below
may help in this direction.
The process connection size and type for various types of instruments are available
in Table-XX
(The following covers the requirements of a power plant and should not be taken as
universal guidelines)
PRESSURE
Gauges(PG) are to be used:i)
ii)
iii)

Pump Discharges (individual-before check valves)

Before and after Pressure reducing stations
Pressurized vessels(Air receiver, boiler drum, dearator etc.)

Switches(PS)
i)
ii)
iii)

Pump discharge(individual when there is discharge MOV)

Common Pump Discharge
Pressurized headers (water, steam or oil)

Transmitters
i)
ii)
iii)
iv)
v)

Common Pump Discharge header

After Pressure reducing stations
Controlled pressurized headers
Pressurized vessels
Wherever Steam/Air flow compensation is required

Notes: For pressure instruments, chemical seal type instruments shall be used for
fluids that are congealing type, highly viscous and corrosive in nature. Except for
chemical seal type instruments, all pressure tappings shall be .

TEMPERATURE
For temperature instruments like gauges, switches, test pockets, thermowell shall
be invariably provided in process lines and vessels. The only exempt cases are
bearing/winding temperature sensors and skin temperature of vessels and tubes. In
general the process connection shall be threaded (1 NPTF/M33X2) & seal-welded
type for pipes and flanged for vessels. However, in special cases ALL thermowells
maybe flanged type. Wherever the line size is less than 100 mm NB, a section of the
pipe is to be expanded to 100 mm to accommodate insertion of thermowell. For
flanged thermowell, 40 NB flange with 150 mm take-off shall be used.
Gauges (TG) are to be used:i)
ii)
iii)

Inlet and outlet of heater and cooler for both fluids.

De-superheater outlets
Pressurized vessels

Switches (TS)
i)
ii)

Are to be avoided as far as practicable

Wherever called for TE/TT should be used

Sensors/Elements(TE)
i)
ii)
iii)

RTDs to be used for below 300 deg C

K-type Thermocouples to be used for > 300 deg C
All sensors shall be duplex type

Transmitters (TT)
i)
ii)

To be used wherever the thermocouple/RTD is used for control.

RTD/TC can be directly connected to DCS/PLC for monitoring only.

FLOW
In a medium sized power plant, the sensors generally used are limited to orifice,
flow nozzle, aerofoil, annubar, mass flow meter and in some cases ultrasonic and
electro-magnetic flowmeters. The guidelines given below are generally satisfactory,
unless the contract specifically calls for otherwise. For all flowmeters, straight run
distances are critical and should be considered well while making the piping
drawings.
Orifice Plate Assemblies
i)
ii)
iii)
iv)

Can be used for water/steam/oil lines from 2-24 NB line size,

preferably horizontal flow.
It can be used for bidirectional flow too.
Flange tapping is satisfactory in most cases. For line size below 4, D,
D/2 tapping should used.
Upstream PT and TE to be provided for compressible fluids flow
compensation.

Flow Nozzle
i)
ii)
iii)
iv)

To be used where the water/steam line pressure and temperature are

high.
Line size from 2- 16 NB. Higher size possible but cost becomes
prohibitive.
Steam flow measurements required for performance monitoring.
Upstream PT and TE to provided fro compressible fluid flow
compensation.

Annubar (Averaging Pitot)

i)
ii)
iii)

To be used mainly for very large bore pipes > 16

Service: Water
Pressure: Medium to low

Aerofoil
i)

To be used for reactangular duct air flow measurement

Mass Flow meter

i)
ii)

These are online meters to be mainly used for oil line (LDO/HSD)
For heat-traced lines, special precautions needs to be taken.

Electromagnetic Flowmeters
I)

Mainly used for water lines below 4. Can be used for larger lines but
better to opt for orifice.

Ultrasonic Flowmeters
i)
ii)

To be used only when called for in larger lines for water flow
measurement
Can also be used for open channel flow measurement like Parshall
Flue, Wedge etc.

LEVEL
Gauges
i)
ii)

iii)
iv)

v)

Reflex type gauges shall be used for all transparent fluids in

pressurized vessel of heights less than 2000 mm.
Each gauge shall not be more than 1200 mm c-to-c. To cover larger
lengths, multiple gauges with at least 50 mm overlap (visible) shall be
used.
Process connection shall be 1 flanged.
Tubular gauges shall be used only when the vessel in atmospheric
pressure, liquid is non hazardous. Other points shall be as per Reflex
gauges.
Float & Board type gauges shall be used for tanks higher than 2000
mm

Switches
i)

ii)
iii)

Side mounted float type switches shall be used wherever there is a

single setpoint. These shall always have external float chamber.
Process connection 1 flanged.
For multiple setpoint, vertical displacer type level switches maybe used
with external float chamber or internal stilling well.
RF type level switches shall be used for solids level (ash and coal)

Transmitters
i)

ii)

iii)

Differential pressure type transmitters can be used for high to medium

pressure application. Remote seal type to be used for services like
LPFO/HFO or corrosive fluids.
For low pressure vessels (condenser hotwell, LPH etc), displacer type,
guided radar type shall be used. (Displacer type should be avoided
because of lack of availability, cost and high maintenance).
Ultrasonic LT shall be used for almost all applications except for very
small (<1000 mm H), high temperature applications. (Height < 15 000
mm)

DESIGN CRITERIA FOR PREPARING P&ID

The following design criteria shall be followed in general for preparing a P&ID unless
otherwise mandated by project specific Design Basis Report. In case of any conflict,
the project DBR shall govern. The following is meant to be basic guidelines only.
1. EQUIPMENT ARRANGEMENT
a. Towers, vessels, fired heaters shall be shown in the upper half of the
diagram, heat exchange equipment in the upper three-quarters, and
machinery equipment in the lower quarter.
b. General flow scheme should be from right or left.
c. The space above the title block shall be left blank for notes
2. PIPING FOR PUMPS
a. Generally the suction pipe and the discharge pipes are different from
the pump nozzles. The suction and discharge nozzles at the pump are
1 size or 2 size small than the pipe. The block valves shall be provided
as per the following:-

Suction

Discharge

b.

Pump Nozzle Size

1-Size smaller than
pipe
2-size smaller than
pipe
Smaller than pipe

Size of Block valve

Same as suction
pipe
1-smaller than line
1-size smaller
than line

Suction Strainers: Generally strainers are provided at all pump

suctions. Following guide lines maybe followed:i. Line size 80 NB or more : T type strainer
ii. Line size 50 NB and smaller : Y type strainer
iii. Dual basket type strainers with three-way valves maybe provided
at common suction lines for 1+1 pumps, wherever online cleaning
and replacement is required.
iv. Strainers more than 150 NB shall be provided with 25NB drains

c. Auxiliary Piping: Auxiliary piping for pumps like cooling water,

condensate, steam etc, are to be shown in a separate drawing.
d. Vent and Drain Valves:
i. Drain and vent hole sizes in the pipe line shall generally be
size. The number of valves shall be one for pressures < 40 kg/cm2
and two for pressures above that.
ii. Horizontal/ Vertical vessels shall have vents on top on both sides.
e. Line Numbering: Identifying the pipelines shall be done in accordance
to ANNEXURE-IX.
Following lines shall be numbered:-

i.
ii.
iii.
iv.
v.
f.

Equipment to Equipment
Equipment to line
Line to atmosphere or drain
All branches and headers
Line number shall change as the deign parameter changes.

Bypass valves: bypass valves maybe provided for control valves, safety
valves, vessels depending on the process requirement. For Control
Valves refer ANNEXURE-IV. For safety valves bypass maybe provided
for toxic gases. For vessels it is mandatory to provide bypass where the
process may uninterrupted when the vessel is taken for service.
g. Utility lines: for all utility lines following instrumentation shall be
provided:i. PG at the inlet or exit for air line.
ii. PG,TG, FT for entry or exit of steam lines
iii. Spectacle blind shall be provided for gas lines in addition to PG, TG
and FT.
iv. PG , TG and FTfor water lines at entry and exit.

ANNEXURE-IX
PIPE TAGGING
The line numbering is done according to the following legend. The basic line number
structure is as follow:
XXX-YYY -ZZZ-UUU-VV-WW
INSULATION THICKNESS (mm)
COLD/HOT/PERSONNEL/NIL
SERIAL NUMBER
PIPE SPECIFICATION
TABLE-2M
NOMINAL BORE DIA (mm)
FLUID CODE-TABLE-1M

TABLE-IM
FLUID
AUXILIARY COOLING WATER

CODE
ACW

FLUID
HIGH PRESSURE STEAM
DRAIN
INSTRUMENT AIR
LIGHT DIESEL OIL
LOW PRESSURE DOSING

CODE
HPD

AUXILIARY STEAM SYSTEM

BLAST FURNACE GAS
BASIC OXYGEN FURNACE
GAS
CARBON DIOXIDE
CHILLED WATER
CLARIFIED WATER

ASS
BFG
BOG

LFW
LPS
LPD

DSW

LOW PRESSURE FEEDWATER

LOW PRESSURE STEAM
LOW PRESSURE STEAM
DRAIN
LOW SULPHUR HEAVY
STOCK(LSHS)
MAIN COOLING WATER
MAIN STEAM
MEDIUM PRESURE STEAM
MEDIUM PRESSURE STEAM
DRAIN
MIXED GAS

COKE OVEN GAS

COG

COLD REHEAT STEAM

CONDENSATE WATER
DEARATOR PEGGING STEAM
DEMINERALISED WATER

CRH
CDS
DAS
DMW

DESUPERHEATING SPRAY
WATER
EFFLUENT WATER
EXHAUST STEAM
FILTERED WATER
FIRE WATER
FURNACE OIL
GAS DRAIN
GLAND SEALING STEAM
GT START-UP AIR
HIGH PRESSURE DOSING
HIGH PRESSURE FEED
WATER
HIGH SPEED DIESEL
HOT REHEAT STEAM

EFF
ESS
FLW
FWS
FOL
GAD
GSS
GSA
DHP
HFW

NAPHTHA
NATURAL GAS
NITROGEN
OIL WASTE WATER
POTABLE WATER
RAW WATER
REFINERY GAS
RO PERMEATE
SEA WATER
SERVICE/PLANT AIR

NAP
NGS
N2G
OWS
PWS
RWS
RGS
ROW
SAW
SAS

HSD
HRH

SERVICE WATER
SUPERIOR KEROSENE OIL

SWS
SKO

CDG
CHW
CLW

IAS
LDO
DLP

LSH
MCW
MSS
MPS
MPD
MXD

HYDROGEN
HIGH PRESSURE STEAM

H2G
HPS

ULTRA FILTER WATER

WASTE WATER

UFW
WWS

VALVE TAGGING
All mechanical valves shall be tagged with 3 alphanumeric characters according to
the following Table
XXX-YYY -ZZZ

SERIAL NUMBER
REFER TABLE-2M BELOW
FLUID CODE-REFER TABLE-1M

TABLE-2M
GATE VALVE
GLOBE VALVE
CHECK VALVE
BALL VALVE
BUTTERFLY VALVE
PLUG VALVE
FOOT VALVE

VG
VL
VC
VB
VU
VP
VF

NEEDLE VALVE
FLOAT VALVE
ANGLE VALVE
RELIEF VALVE
SLUICE GATE
KNIFE GATE
GOGGLE VALVE

VN
VO
VA
VR
VE
VK
VV

PIPE SPECIFICATION
The pipe specification gives the physical characteristics of the pipe material and
rating by a code comprising of 4 alphanumeric characters. REFER Table-2M for the
details.

APPLICATION
PIPE MATERIAL GRADE
PIPE RATING (ASME/DIN)
PIPE MATERIAL

TABLE-2M
PIPE MATL
CLASS(X)
COD MATL
E
CLASS

PIPE MATERIAL(Z)
CODE
A

CAST IRON

B
A
B

CARBON
STEEL

C
D
E
A

GALVANIZED
CARBON
STEEL

B
C
A

ALLOY
STEEL

B
C
A

STAINLESS
STEEL

B
C

PLASTIC
AND
DERIVATIVE
S

MATERIAL
Centrifugally
cast spun CI
Vertically
Cast spun CI
IS-1239/IS3589
A-106-GR-B
A-53 GR-B

APPLICATION (Q)
APPLICATIO
N
IBR

PIPE RATING
CLASS(Y)
COD RATING
E
1
150#

FIRE SAFE

300#

VACUUM

600#

ELEC
TRACED
STEAM
TRACED

900#

1500#

8
B
C

2500#
PN-2.5
PN-6

PN-10

PN-16

PN-20

COD
E
C

API 51-GR-B
A-106 GR-C
IS1239(GALV)
A-106-GRB(GALV)
A-53-GRB(GALV)
A-335 GRP11
A-335-GRP22
A-335-GRP91
A-312-TP304
A-312-TP316
A-312-TP321
GLASS
REINFORCED
POLYESTER
UNPLASTICIS
ED PVC

COPPER

Example:D6BC: IBR Pipe of material A-335-Gr-P22, rating 1500#

Note: The above codification is limited and specific to Thermax Power Division and
should not be construed as a general pipe naming convention.

EQUIPMENT TAGGING
All equipment in the P & ID is identified with a 4-character alpha-numeric name as
per the following convention:
XX

YY

ZZ

ALPHANUMERIC-REF NOTE-1
BELOW
SERIAL NUMBER-REFER NOTE-2
BELOW
EQUIPMENT CODE-TABLE-4M
SYSTEM CODE-TABLE-3M

Note-1: One digit alphanumeric code. Starts from A when there is standby. The
standby identified by B, C etc. In case there is no standby, the character is 0.
Note-2: Serial number of similar equipment under the same system code.
TABLE-3M
SYSTEM CODE
CODE
01
02
03
04
05
06
07
08
09

SYSTEM NAME
FUEL SYSTEM
GAS TURBINE SYSTEM
GAS TURBINE EXHAUST SYSTEM
STEAM GENERATION SYSTEM
STEAM TURBINE GENERATOR SYSTEM
WATER SYSTEM
FIRE WATER SYSTEM
COMPRESSED AIR SYSTEM
AIR CONDITIONING AND VENTILATION SYSTEM
TABLE-4M

NOZZLE DESIGNATIONS
Nozzles fro tanks/vessels shall be identified as per the following designations
CODE
M1
M2
N1
N2
N3
N4
N5
N6
N7

PURPOSE
ROOF MANHOLE
SIDE MANHOLE
INLET
INLET-SPARE
OUTLET
OUTLET-SPARE
OVERFLOW
DRAIN
LEVEL TRANSMITTER

N8
N9
N10
N11
N12
N13
N14
N15
N16

LEVEL GAUGE
LEVEL SWITCH
VENT
RECIRCULATION
SAMPLING POINT
PRESSURE GAUGE/TRANSMITTER
TEMPERATURE ELEMENT/GAUGE
XXX
XXX

EQUIPMENT CODE

TABLE-5M
EQUIPMENT DESCRIPTION
AIR CONDITINER (SPLIT)
AIR CONDITIONER SYSTEM
AIR CONDITIONER WINDOW
UNIT
AIR DRIER
ASH HANDLING SYSTEM
ASH HANDLING VACUUM
TYPE
ASH HANDLING -WET
CONVEYING
BAG FILTER
BLOWER
BREATHER VALVE
CENTRIFUGE
CHILLER
CHLORINATOR
CLARIFIER
COMPRESSOR
CONDENSER AIR COOLED
CONDENSER-WATER
COOLED
COOLING TOWER
CRANE
CRUSHER
CONVEYOR
DAMPER
DIVERTER DAMPER
DAMPER-GUILLOTINE TYPE
DEARATOR
DEGASSIFIER
DENSE PHASE SYSTEM
DIESEL ENGINE
D.M.PLANT
ELECTROSTAIC
PRECIPITATOR
EXPANSION JOINT
FAN
FIRE FIGHTING EQUIPMENT
FIRE HYDRANT
FIRE PROTECTION
EQUIPMENT
FLAME ARRESTOR
FLEXIBLE JOINT
FLOW GLASS
FOAM SYSTEM
FUEL HANDLING SYSTEM
GAS CONDITIONING SKID
HEAT EXCAHNGER
HOIST
HOSE BOX
HOSE CANVAS

COD
E
SA
AC
WA

EQUIPMENT DESCRIPTION

CODE

HOSE METALLIC
HOSE RUBBER
HRSG

HM
HR
HB

AD
AH
VS

HUMIDIFIER
HVMS SPRAY SYSTEM
INLET AIR FILTER

HU
HV
IF

WC

MC

BF
BL
BV
CZ
CH
CL
CF
CM
CI
CW

MECHANICAL DUST
COLLECTOR
MVWS SPRAY SYSTEM
OIL WATER SEPARATOR
PRESSURE VESSEL
PULLEY BLOCKS
PUMP
PURIFIER
RADIATOR
RESERVOIR
RESERVOIR-EARTHEN
RESTRICTION ORIFICE PLATE

CT
CR
CX
CY
DM
DV
DI
DA
DF
DP
DE
DP
ES

REVERSE OSMOSIS PLANT

RUBBER BELLOWS
SCREEN-COARSE
SCREEN-FINE
SIDE STREAM FILTER
SILENCER
SILO
SOOT BLOWER
STACK
STEAM GENERATOR
STRAINER-BASKET TYPE
STRAINER-CONICAL TYPE
STRAINER-TEE TYPE

RO
BE
SE
SF
SS
SL
SO
BS
SK
SG
SB
SC
ST

EJ
FN
FE
FH
FP

STRAINER-Y-TYPE
TANK
TRAP-BALL & FLOAT
TRAP-INVERTED BUSCKET
TRAP-THERMOSTATIC

SY
TK
TB
TI
TS

FA
FJ
FG
FM
FS
GS
HE
HO

TRAP-THERMODYNAMIC
TRAVAGRATE BOILER
TURBINE GAS DRIVEN
TURBINE-STEAM DRIVEN
ULTRA FILTER PLANT
VENTILATION SYSTEM
VENTURI SCRUBBER
WASTE HEAT RECOVERY
BOILER
WATER TREATMENT PLANT
WEIGHING SCALE

TD
MB
GT
TG
UF
VT
SV
WB

HB
HC

MV
OS
PV
PB
PP
PU
RA
RS
RE
OR

WT
WS

ANNEXURE-III
INSTRUMENT TAGGING
All instruments in a plant shall have unique tag number which propagates through
all other following drawings/documents like Instrument Index, DCS/PLC IO list,
Specification and data sheets , hook up drawings etc. There are various conventions
of tag numbering followed which are regionally, process wise or company wise
followed like ISA, KKS, GOST, NORSOK etc. Each of these methods have the pros
and cons when analysed against some concept or other. In power plants KKS system
of tagging is widely followed in Europe since it originated from Germany, whereas
ISA is followed in US. In Thermax, we have found ISA system of tag numbering more
convenient and have adopted with minor adjustment.

Instruments, control and shut-off valves and drives are numbered according to the
following legend
XX-YYY -ZZZZS

ALPHANUMERIC TAG NUMBER

INSTRUMENT IDENTIFIER
PROCESS SECTION IDENTIFIER

PROCESS SECTION-XXX
01
02
03
04
05
06
10
11
12
20
21
22
30
31
32
40
41
42

ELECTRICAL PARAMETRS-33KV
ELECTRICAL PARAMETERS-11KV
ELECTRICAL PARAMETERS-6.6
KV
ELECTRICAL PARAMETERS415/690 V
UPS PARAMETERS
DG SET PARAMETERS
BOILER COMMON
BOILER-1
BOILER-2
STEAM TURBINE COMMON
STEAM TURBINE-1
STEAM TURBINE-2
ASH HANDLING-COMMON
SERVICES
ASH HANDLING-BOILER-1
ASH HANDLING-BOILER-2
BALANCE OF PLANT
AIR COMPRESSOR-1
AIR COMPRESSOR-2

60
70
71

WATER TREATMENT PLANT

GAS TURBINE COMMON SYSTEMS
GAS TURBINE-1

72

GAS TURBINE-2

80
90
91

FIRE ALARM SYSTEM

COAL HANDLING PLANT
LIMESTONE HANDLING PLANT

The numbering system as given in this

43 AIR DRIER
50 ESP COMMON
51 ESP-BOILER-1
52 ESP-BOILER-2
INSTRUMENT FUNCTION IDENTIFIER-YYYY

Table is a typical and may be re-created

depending on the configuration of the
plant

Function

Transmitt
er

Controll
er

PT
TT

PIC
TIC

Indicator

Senso
r

Loc
al
PG
TG

Remo
te
PI
TI

FG
LG
DP
G
*

FI
LI
DPI

FE
LE

FT
LT
DPT

FIC
LIC
DPIC

ApHI

ApHT

ApHIC

Conductivi
ty
OxygenGas
Dissolved
Oxygen
Particulat
e
Sox

ACI

ApH
E
ACE

AOXI

AOXT

ADOI

APMI

ASOXI

NOx

ANOXI

AOX
E
ADO
E
APM
E
ASO
XE
ANO
XE

Current
Voltage
Power
Position
Torque
Energy

A
V
P

II
EI
JI
ZI
WI
WQI

Pressure
Temperat
ure
Flow
Level
Diff
Pressure
pH

Switch

AlarmHH,H,L,LL

Function

ACT

ADOT
APMT
ASOXT
ANOXT
IT
ET
JT
ZT
WT

Note: All transmitters are with integral indicators and hence these indicators are
specifically spelt out with a distinctive tag. (*)

Totalizer