USERS MANUAL FOR CONTROLLER

USERS MANUAL
FOR
ELECTRONIC JACQUARD CONTROLLER

CATALOGUE:
1. BRIEF INTRODUCTION
2. HOME PAGE OF CONTROLLER
3. DESIGN OPERATION
4. PARAMETER 1
5. PARAMETER 2
6. PARAMETER 3
7. STATUS PAGE

1 / 13

USERS MANUAL FOR CONTROLLER

1. Brief Introduction
This controller adopts blue&white screen (240x182), operated by
buttons. Its easy to learn, and high stability. Now please find the
below operation instruction.

2. Home Page of Controller

SHANGHAI ZHONGJIAN JACQUARD SYSTEM

File

ZJ1X1-1.EP

Repeat

: 10

Weft Number 1
Group

Production

Speed

The controller will be on Home Page by pressing the button M on the panel. On this page,
the contents from top to bottom are:
1. File:. ZJ1X1
2. Repeat :10
3. Weft number : 1
4. Group ; A
5. Production : 0
6. Speed : 0
Here are the meanings of the above six items:
1. It means it displays the file name of the weaving process currently, this content will be
2 / 13

USERS MANUAL FOR CONTROLLER

changed when the users choose to select a new craft pattern file.
2. It means it displays the number of cycles of the weaving process currently being used (the
total number of shuttles), this content will be changed when the users choose to select a
new craft pattern file.
3. It means the current weft number. When the machine is running one round forward, this
number will be +1; when the machine is running one round backward in the
pick-finding status, this number will be -1. When the number of +1 exceed the total
harness, then it will change to 1; when the number of -1 less than 1, then it will
change to the total harness.
4. It means it will display the current operator belongs to which group, this content can be
setted in parameter two, there are three options A, B, C.
5. It means the circulation number that has been finished. Each time, a circulation is finished,
the number will change to +1.
6. It means the current loom running speed, rev / sec.

3. Design Operation

SHANGHAI ZHONGJIAN JACQUARD SYSTEM

Select

Design

Delete

Design

Amend Design
Auto Link Design
Read From UDisk
Write To UDisk

The controller will

be on Design Operation by pressing the button F1 on the panel. On
3 / 13

USERS MANUAL FOR CONTROLLER

this page, the contents from top to bottom are:
1. Select Design
2. Delete Design
3. Amend Design
4. Auto Link Design
5. Read From U Disk
6. Write To U-Disk
Here are the meanings of the above six items:
1. Select Design: First by press the button
then the indication sign will be on this
item. Then press , the controller will be on select a design page. On this page, the
customer will find the names in the U-disk. The customer can press to go
upward or downward,
means page turning. If the customer wants to select a
design, then press
to move to this design and the press S , then this design
name will be highlighted. Press , then the system will start to deal with this design.
During this time, when the percentage is 100%, it means the customer can start the
loom to weave.
2. Delete Design: First by press the button then the indication sign will be on
this item. Then press , the controller will be on delete a design page. On this page,
the customer will find the names in the U-disk. The customer can press
to go
upward or downward,
means page turning. If the customer wants to delete a
design, then press
to move to this design and the press S , then this design
name will be highlighted. Press , then the system will start to deal with this design.
Note: the deleted design cannot be recovered.
3. Amend Design: first ,using the "up" "down" arrow keys to move the arrow indicator to
move to that option, and then press "" button, the system will enter the Change Design
screen. The screen will display the file name pattern within the system hard disk, press
the "up" "down" arrow keys to move up and down arrow mark achieved, press the "left"
and "right" arrow keys to realize the flip operation. In the modified pattern screen, press
"up", "down" arrow keys to move the arrow indicator to the previous corresponding file
name, press the "select" button, the current file name is highlighted, then press ""
4 / 13

USERS MANUAL FOR CONTROLLER

button, the system enters the modified screen the sub-screen, users enter latitude number,
pin number to call up the specified pin data while modifications, changes are complete,
press the "OK" button to save and exit. Note: Before performing modification pattern,
you must first enter the password "010101", it allows you to modify.
4. Auto Link Design: First, using the "up" "down" arrow keys to move the arrow indicator
to move to that option, and then press "" button, the system will automatically connect
into the picture.The main function of this screen is to choose a series of pattern files and
documents up these patterns to combine into one large pattern weaving process
documents.Users select a file name pattern, the pattern is completed automatically
connected.
5. Read From U Disk: First by press the button
then the indication sign will be
on this item. Then press , the controller will be on read U-Disk page. But before this,
the customer should first connect the U-Disk. For some U-Disk, it will take longer to
respond, so we suggest that the customer can wait 3-5 seconds. After the U-Disk is
identified, the controller will show the design names in the U-Disk. The customer can
press
to go upward or downward,
means page turning. On this
page, press
to move to this design and the press S , then this design name
will be highlighted. Press , then the system will start to copy the design to the
system. When the percentage is 100%, it means the copy is finished. The customer also
can choose several designs then press

to copy these designs.

6. Write To U-Disk: First by press the button

then the indication sign will be on
this item. Then press , the controller will be on write U-Disk page. But before this,
the customer should first connect the U-Disk. For some U-Disk, it will take longer to
respond, so we suggest that the customer can wait 3-5 seconds. After the U-Disk is
identified, the controller will show the design names in the controller system. The
customer can press
to go upward or downward,
means page
turning. On this page, press to move to this design and the press S , then
this design name will be highlighted. Press , then the system will start to copy the
design to the system. When the percentage is 100%, it means the copy is finished. The
customer also can choose several designs then press to copy these designs to the
5 / 13

USERS MANUAL FOR CONTROLLER

U-Disk.

4. Parameter 1

SHANGHAI ZHONGJIAN JACQUARD SYSTEM

Jac Pick Num2688

Start Pick Num1
Jacquard StyleBONAS
First Pick PosLeftBack
Loom StyleZF

The controller will be on Parameter 1 by pressing the button F2 on the panel. On this
page, the contents from top to bottom are:
1. Jac Pick Num : 2688
2. Start Pick Num : 1
3. Jacquard Style : BONAS
4. First Pick Pos : Left Back
5. Loom Style: ZF
Here are the meanings of the above five items:
1. Jac Pick Num: This item is for the actual hook of the jacquard. First by press the button

then the indication sign will be on this item. Then press , after the sign
blinks, the customer can change the parameter by number buttons. After this, press
to confirm and save the revise. But if the parameter the customer put does not conform the
system, then the revise is invalid and the system will show the last correct parameter.
2. Start Pick Num:This item is for the pattern of the actual first hook position. First by press
the button
then the indication sign will be on this item. . Then press ,
after the sign blinks, the customer can change the parameter by number buttons. After this,
6 / 13

USERS MANUAL FOR CONTROLLER

press to confirm and save the revise. But if the parameter the customer put does not
conform the system, then the revise is invalid and the system will show the last correct
parameter.
3. Jacquard Style: This item is for the jacquard model. First by press the button
then the indication sign will be on this item. Then press , the item will be highlighted.
The customer can press to adjust this parameter. For this item, there are the
following options: STB8M8,STB16M16,STB24M24,STB24M12 etc. Then pressto
save the revise.
4. First Pick Pos: This item is for the harness position, ie, the first hook position of the
jacquard. There are four options: LeftBack, LeftFront, RightBack, and RightFront. The
customer can press
to adjust this item. Then press to save the revise.
5. Loom Style: This item is for the loom. First by press the button then the
indication sign will be on this item. Then press , the item will be highlighted. The
customer can press
to adjust this parameter. After the revise, press to
save the revise. Note: after the revise, the customer need to restart the controller so that
the new parameter will be valid.

5. Parameter 2

7 / 13

USERS MANUAL FOR CONTROLLER

SHANGHAI ZHONGJIAN JACQUARD SYSTEM

Amend Weft Num1

Clear Product0
Sel Work GroupA
Set End Cycles0
Password Input
Use Start Signal0

The controller will be on Parameter 2 by pressing the button F3 on the panel. On this
page, the contents from top to bottom are:
1. Amend Weft Num : 1
2. Clear Product: 0
3. Sel Work Group ;A
4. Set End Cycles : 0
5. Password Input
6.

Use Start Signal:0

Here are the meanings of the above six items:

1. Amend Weft Number: This item is for adjusting the weft number, and controller system
has the regulation on this item, so if the customer input the incorrect parameters, the
system will refuse to revise and back to the correct last time weft number. First by press
the button
then the indication sign will be on this item. Then press ,
the sign will blink then press to delete the weft number and input a new number to
revise. After this, press then the weft number will change to the input number and
start to weave. The customer can also press or to make the weft number
+1 or -1.
2. Clear Product: This item is for output reset. First by press the button
then the
indication sign will be on this item. Then press , the sign will blink. Then press the
number 0 to reset the output. Then press to save the revise.
3. Sel Work Group :This item is used to specify the current operator belongs to which group,
8 / 13

USERS MANUAL FOR CONTROLLER

A, B, C three groups can be choosed. First, using the "up" "down" arrow keys to move the
arrow indicator to move to that option, and then press "" button, the option is
highlighted, press "up", "down" arrow keys to adjust the adjustment is completed , press
the OK button to save the modified value, while highlight disappears.
4. Set End Cycles: This item is for the ration setup, ie. to set how many circulation of the
current design. Each circulation stands for the output number 1. When the output number
surpass the ration set number, then the jacquard will sent the loom a stop signal, then the
loom will stop. First by press the button
then the indication sign will be on this
item. Then press , the sign will blink. Then input the numbers to setup. After this,
press to save the revise.
5. Password Input: This item is for password input. First by press the button
then
the indication sign will be on this item. Then press , the sign will blink. Then input
password. Normally, the customer can ignore this item, but when there is special case, the
customer can contact with us to get the password.
6. Use Start Signal:0 means there is no need to connect Forward or Reverse signal,1
means there should connect Forward or Reverse signal.This item has been confirmed after
the new machine is debugged,dont change it in the following production
process,otherwise some with automatical function looms will appear mispick. Our
program has this parameter only in the end number :206 version and later version,so there
is no affect in the earlier version that without this parameter.

6. Parameter 3

9 / 13

USERS MANUAL FOR CONTROLLER

SHANGHAI ZHONGJIAN JACQUARD SYSTEM

Comm Test
Sel Language

English

Color Channel

A:01->B:01

Channel Polar

B:01->D:D

Sending Fre 10
Sending Times

The controller will be on Parameter 3 by pressing the button F4 on the panel. On this
page, the contents from top to bottom are:
1. Comm Test
2. Sel Language: English
3.Color Channel: A:01->B:01
4.Channel Polar B:01->D:D
5.Sending Frequence:10
6.Sending Times:1

Here are the meanings of the above six items:

1. Communication Test: This item is for testing the communication system. First by press
the button
then the indication sign will be on this item. Then press , the
sign will blink ,and it will show 0 at the same time,system will test communicate once per
second.If there is some problems with communication,then the number will be plus 1.If you
want to finish the test, then press and the sign will also disappear.This function only
can be used in the stationary state,when the loom is running ,this test is invalid.
2. Selecting Language: This item is for selecting language, now there are only two options:
Chinese & English. First by press the button
then the indication sign will be on
this item. Then press , the sign will blink then press
to select, then press
to save the revise.
3. Color Channel: This item is for the 32 functional hooks of the design file correspond to
10 / 13

USERS MANUAL FOR CONTROLLER

the 32 output of the circuit. First by pressing the button then the indication
sign will be on this item. Then press , the sign will blink. Then the customer can
revise. For example, if the customer wants the first functional hook correspond the second
output, then please setup as follow:
A:01->B:02, customer can adjust by pressing

, after the revise, please

press to save.
4. Channel polarity :This process is used to change the contents of the document should be
32-pin capabilities for the 32-channel output circuit, first by using the "up" "down" arrow
keys to move the arrow indicator to move to that option, and then press "" button the
cursor flashes can be set to start operations, for example: if you want to process
documents in the first function in the output circuit of the second needle channel, set the
contents are as follows:
A: 01 -> B: 02, its contents can be used "up", "down", "left" and "right" arrow keys to
adjust the adjustment, press " " button, the system saves the setting, the cursor
disappears.
5. Sending Frequency: This item is for setting sending data frequency of jacquard. First by
pressing the button then the indication sign will be on this item. Then press
, the sign will blink. Then the customer can revise. After the revise, please press
to save.
6. Sending Times:This item is for setting data sending times. First by pressing the button

then the indication sign will be on this item. Then press , the sign will
blink. Then the customer can revise. After the revise, please press to save.

7. Status Page

11 / 13

USERS MANUAL FOR CONTROLLER

SHANGHAIZHONGJIAN ACQUARD SYSTEM

System StaetOK!
HardDisk StateOK!
Data ChannelERROR!
Legal UserERROR!
Program VersionP1306252208
Random Code543965246

The controller will be on Status Page by pressing the button F5 on the panel. On this page,
the contents from top to bottom are:
1. System State OK!
2. HardDisk StateOK!
3. Data Channel ERROR!
4. Legal User ERROR!
5 .Program VersionP1203XX100
6. Random Code 543965246
Here are the meanings of the above six items:
1. System State: This item is to check whether the disk works normally or not, when it is
normal, it shows OK, otherwise, it shouws ERROR.
2. HardDisk State: This content display system hard drive is working properly when the
system is working properly, the display OK, otherwise display ERROR!!.
3. Data Channel: The content display data channel electronic control system is normal, if
normal then display OK, otherwise display ERROR!!.
4. Legal User: This item is to show whether the customer has the right to use this controller
system. Normally when its out of limited time, the system will be locked, and the customer
cannot use this system again. When this item shows OK, it means the customer can use this
system; but when it shows ERROR, it means it cannot be used.
5. Program Version: This item shows the version of this program.
6.Random Code: This item shows a series of flexible digits number. When the User item
12 / 13

USERS MANUAL FOR CONTROLLER

shows ERROR, and the system cannot be used, the customer can report this series number
to us. (After copied the random number, please do not power off, do not press other buttons
until you receive a password.)We will inform you a password based on the series number.
Users press F3 to enter the "password" option, input the password, then the system will be
normal again.

13 / 13