Scribd
Upload
254 views

Atari 5200 VCS Adapter Modification PDF

This document provides instructions for retrofitting an Atari CX5200 Super System PCB (model CA018087) to allow compatibility with the new Atari YCS Cartridge Adaptor (CX55). The retrofit involves isolating pin 24 on connector J1 from ground, adding five diodes and three resistors, and running three wires (black, green, red) between the added components and J1. Installation and testing procedures are outlined to verify proper functionality with the adaptor after completing the retrofit.

Uploaded by

Oscar Arthur Koepke
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
254 views

Atari 5200 VCS Adapter Modification PDF

This document provides instructions for retrofitting an Atari CX5200 Super System PCB (model CA018087) to allow compatibility with the new Atari YCS Cartridge Adaptor (CX55). The retrofit involves isolating pin 24 on connector J1 from ground, adding five diodes and three resistors, and running three wires (black, green, red) between the added components and J1. Installation and testing procedures are outlined to verify proper functionality with the adaptor after completing the retrofit.

Uploaded by

Oscar Arthur Koepke
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

)k

Consumer Product Service


Manager of Technical Support

ATARI"
MODEL:

UPGRADE BULLETIN
Atari CX5200 Super game (PCB CA018087)

number

UB
vcs
01

DATE: July 7, 1983

.
SUBJECT:
PCB Retrofit to allow use of Atari YCSTM Cartridge Adaptor

UPGRADE DESCRIPTION:
Applies only to CX5200' PCB, PIN CA018087. Allows use of the new Atari
YCS Cartridge Adaptor (CX55). AU other CX5200 PCB's have the retrofit
components built into them and require no modification to accommodate the
adaptor.

lNSTALLAnON PROCEDURE:
Use attached retrofit procedure.

TESTING PROCEDURE:
As outlined in retrofit procedure.

If you have questions or need further assistance, call the Atari Techline

Specialist.
Inside California
(800) 672-1466
Outside California
(800) 538-1535

.,.., ".,

"

/~ ".

ves CARTRIDGE ADAPTOR PCB


RETROFIT PROCEDURE
1. Remove the top cover of the CX5200.
2. Verify that the PCB Part Number is CA018087. (If it is not this number, there
is no need for the modification. Reinstall cover, insert adaptor, go to step 13
and test.)
3. Remove both the top and bottom PCB shields.
4. Using either an X-ACTO knife or a Dremel tool (150 Bit), isolate Pin 24 of Jl
from ground by making a "V" or "U" shaped cut in the trace on the component
side of the PCB (See Figure 1). Be careful not to isolate Pins 23 and 25 from
ground.
IT IS EXTREMELY IMPORTANT THAT PIN 24 OF Jl BE COMPLETELY
ISOLATED FROM GROUND.
Use an Ohm Meter to verify that Pin 24 has been isolated from ground.

Figure 1. Pin 24 Isolation.


5. If the kit has not already been pre-formed (see Figure 2), use needle-nosed
pliers and wire cutters to pre-form the kit. Use Figure 2 as a reference.
D1

:>

ASS! 1

C1: .1uf ceramic


R1: 1k
R2: 1k
R3: 3.3k
D1-5: 1n914

ASSY2

J
Fis!Ure 2. Pre-form Assembly

D4&D5

6. Using Figure 3 as a reference perform the following:


A. Solder cathode of 01, Assembly 1 to R26.
B. Pass Assembly 1 wire, (BLACK) through hole in J 1.
C. Solder cathode of 04, to CD.
o. Solder anode of 04, to C14.
E. Solder 0.5 to RIO (Note polarity).
F. Solder cathode of 02, Assembly 2 to Cl0.
G. Solder cathode of 03, Assembly 2 to Rl r:
H. Solder R3, and Cl, Assembly 2 to R12.
I. Pass Assembly 2 wire (GREEN) through hole in J 1.
J. Solder one end of REO jumper wire to L8.
K. Pass REO jumper wire through hole in Jl.
Jl

o
f

XA3

>

!!

o ,," :"6 f
ii

"

0
,

XAll

ij 0>
"

!AI~I

0>

.,5 '

i!

"

XAlOl

0>

Figure 3. Retrofit Oiagram.

7. Using Figure 4 as a reference, perform the following:


A.
B.
C.
D.

Solder Assembly I wire (BLACK) to Pin 24 of JI.


Solder Assembly 2 wire (GREEN) to Pin 30 of J1.
*Solder RED jumper wire to Pin II of J I.
*Solder other end of RED wire to bottom leg of L8.

NOTE:Be sure to leave enough slack in the wires to allow reassembly of the shield.

**CAU110N**********
After soldering, use an Ohm Meter to make sure that no solder bridges or
shorts were formed adjacent to Pins 11,24, and/or 30 of JI.
*******************+CAU110N+****+++++++++**+++++

= Take extra care to avoid connecting the RED wire to any grot.nd pins. If
the RED wire is grounded, the 5200 Power Adaptor will bum out.

Figure 4. Wire Connection Diagram.


8. Place the top housing face down on the workbench.
9. Using needle-nosed pliers, grasp the pin indicated in Figure 5, and twist it off.
10. Replace the shielding on the uni t ensuring that the red wire is routed as in Fig. 4.
11. Before reassembling the unit, place the PCB into the bottom housing and
replace the top housing. DO NOT SECURE HOUSINGS.
12. Using the 1.1 Diagnostic Cartr idge perform a quick check to ensure that the
modifications did not affect the performance of the unit. If the unit fails,
return to the modification procedures, and make certain that all steps were
fully and completely performed. The modifications will not affect game play or
the unit's performance.
13. Turn off the unit.

I
1

I 0

IJ

POST TO BE REMOVED

'=
0

""
0

Figure 5. Top Cover P in Removal


Ill. 'Remove the Diagnostic Cartridge and install the Cartridge Adaptor.

15. Use the 2.6 Diagnostic Cartridge to perform a quick check to ensure that the
adap.tor is functional.
16. If the adaptor does not function properly, step through the modification
procedures to ensure that all modifications were completely and correctly
performed.
17. If all modifications were installed correctly and the Cartridge Adaptor does not
function properly, use a DVM to determine which component or aSsembly is
defective.
18. 'R eplace the defective component or assembly.
19. Completely reassemble the unit, using the screws removed in Step 1 to secure
the two housings together.

You might also like