Scribd
Upload
205 views

ME 472 - Engineering Metrology and Quality Control and Quality Control

This document provides an introduction to metrology and quality control. It defines metrology as the science of measurement, including theoretical and practical aspects. Measurement is comparing an unknown quantity to a known standard using a consistent system of units to obtain a numerical value within certain limits of accuracy and precision. Inspection examines if part characteristics conform to specifications. High quality is defined as a product reliably performing its functions for a long time in a convenient manner. Inspection and measurement are important to achieve continuous quality improvement. Inspection should occur during production for early defect detection and reduced costs. Dimensional measurements and ensuring dimensional accuracy within tolerances are key aspects of inspection.

Uploaded by

pa390786
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
205 views

ME 472 - Engineering Metrology and Quality Control and Quality Control

This document provides an introduction to metrology and quality control. It defines metrology as the science of measurement, including theoretical and practical aspects. Measurement is comparing an unknown quantity to a known standard using a consistent system of units to obtain a numerical value within certain limits of accuracy and precision. Inspection examines if part characteristics conform to specifications. High quality is defined as a product reliably performing its functions for a long time in a convenient manner. Inspection and measurement are important to achieve continuous quality improvement. Inspection should occur during production for early defect detection and reduced costs. Dimensional measurements and ensuring dimensional accuracy within tolerances are key aspects of inspection.

Uploaded by

pa390786
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

ME 472 Engineering Metrology

and Quality Control


Chp 1 - Introduction to Metrology and Quality

Mechanical Engineering
University of Gaziantep

Dr. A. Tolga Bozdana


Assistant Professor

Definition of Metrology
Metrology
Comes from greek metron (measure) and logy.
It refers to science of measurement, including all
theoretical and practical aspects of measurement.

Measurement
It is the procedure of comparing an unknown quantity to a known standard by means
of consistent system of units.
Provides a numerical value of q
quantity
y within certain limits of accuracy
y and precision.
p

Inspection
It is the procedure in which part characteristics (e.g. dimension) are examined whether
they conform to design specification.
Many inspection procedures rely on measurement techniques while others use ga(u)ging
methods (simply determine whether the part passes or fails inspection).
1

Definition of Quality
Product Quality
It refers to a products fitness for use.
It is the totality of features that bear on a products ability to satisfy a given need.

Need for Quality


Quality is a very important aspect of manufacturing.
It is a big issue (wide rage of topics like TQM, Six Sigma, Taguchi, ISO Standards, etc.)
Needed for interchangeable manufacturing.
Basic concept of standardization and mass production.
Components of a product must fit together, assemble properly and be replaceable.
Quality should be built into a product.
j g
goal.
Prevention of defects is a major
2

Measure of Quality
High Quality Product

Low Quality Product

performs its functions reliably

does not perform its function reliably

performs its functions for a long time

fails or breaks after short time of use

performs its functions conveniently

difficult to use

GOAL
Continuous Quality Improvement
(functionality reliability
(functionality,
reliability, durability
durability, ))

Inspection & Measurement

What?

When?

How?
3

What to Inspect?
Inspection specific to PRODUCTS
Electronic parts (circuits, chips, etc.)
Machine elements (engines, brakes, gears, etc.)
Heat and thermodynamic components (engines, fuel injectors, etc.)
Medical and Bio-related products (implants, dental devices, surgical parts, etc.)
Aerospace components (turbine blades and discs, airplane body, etc.)

I
Inspection
i specific
ifi to PROCESSES
Chip removal processes (turning, milling, drilling, etc.)
Chipless manufacturing (casting, molding, forging, etc.)
Non-traditional methods (EDM, ECM, laser ablation/cutting, etc.)

When to Inspect?
Inspection AFTER production
x costly production steps already complete
x high cost of rejection or rework
x difficult to test for all possible defects
x difficult to identify responsibility for defect

Inspection DURING production


y at each p
production step
p
defects found early,
reduced cost of rejection or rework
process improvement
p
facilitates continuous p

How to Inspect?
Measurement of DIMENSIONS
Linear measurements (length, thickness, etc.)
Angular measurements (taper, angle, etc.)
Measurement of surface texture (roughness, waviness, etc.)
Measurement of geometric shape (roundness
(roundness, flatness
flatness, squareness
squareness, etc
etc.))
Measurement of screw threads and gears

Inspection for DIMENSIONAL ACCURACY


post-process (traditional)
in-process (modern trend)

DIMENSIONAL TOLERANCES
permissible variation in dimensions
p
directly affects product quality and cost
6

Scale of Measurement
Large scale (low frequency) measurements
Measurements at macro levels
Dimension (length, angle, etc.)
Tolerance
Form error (contour measurement)

M di
Medium
scale
l (medium
( di
f
frequency)
) measurements
t
Measurements at meso levels
Surface
S f
t t /t
texture/topography
h (waviness)
(
i
)
Geometric shape (flatness, roundness, etc.)

Small scale (high frequency) measurements


Measurements at micro levels
Surface texture/topography (surface roughness)
7

You might also like