Scribd
Upload
456 views

Balmar - Temperature Sensor Manual

This document provides installation instructions for an optional alternator and battery temperature sensor. It describes installing the alternator temperature sensor on the alternator to monitor temperature and reduce output if it gets too hot. It also describes installing the battery temperature sensor on the battery to monitor temperature and modify or stop charging if it gets too hot to prevent overheating. Both sensors connect to the voltage regulator and send a signal to ground a dash lamp to indicate any overheating issues.

Uploaded by

tecnicoeem
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
456 views

Balmar - Temperature Sensor Manual

This document provides installation instructions for an optional alternator and battery temperature sensor. It describes installing the alternator temperature sensor on the alternator to monitor temperature and reduce output if it gets too hot. It also describes installing the battery temperature sensor on the battery to monitor temperature and modify or stop charging if it gets too hot to prevent overheating. Both sensors connect to the voltage regulator and send a signal to ground a dash lamp to indicate any overheating issues.

Uploaded by

tecnicoeem
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Optional Alternator And Bettery Temperature Sensor

Installation Instructions
Alternator Temperature Sensor (MC-TS-A)
With the Alternator Temperature Sensor installed, the Max Charge and ARS-4 voltage regulators can monitor the
alternator and respond if ambient temperature conditions are detected. Once an over-temperature condition is
detected, the regulator will reduce alternator field current to 50%. This will reduce the amperage output and
horsepower load on the engine and belts, thus, giving the alternator an opportunity to cool to normal operating
temperatures.
At the same time, the regulator will send the Dash Lamp terminal to ground,
allowing the operator to identify a potential system problem if a dash warning
light or audible alarm are used in conjunction with the Dash Lamp circuit. To
install the Alternator Temperature Sensor:
1. Attach the thermister lug to one of the four mid-case mounting bolts as
shown in the image at right.
2. Using cable ties, attach the length of the sensor cable to the regulator
wiring harness.
3. Plug the positive (red) and negative (black) sensor leads into the Alternator
Temperature Sensor terminal pins on the regulator (as indicated by the
legend on the side of the regulator). Use care to match polarity as
indicated.

Battery Temperature Sensor (MC-TS-B)


In addition to its ability to completely discontinue charging when a thermal runaway condition is detected at your
battery, the regulator can also modify charging voltage to compensate for smaller changes in ambient battery
temperatures (temperature compensation is only available on Battery #1 terminals -- battery #2 terminals react only
to over-temperature conditions).
In addition to shutting down charging in a catastrophic over-temperature
condition, the regulator will send the Dash Lamp terminal to ground, allowing
the operator to identify a potential system problem if a dash warning light or
audible alarm are used in conjunction with the Dash Lamp circuit. To install the
Battery Temperature Sensor:
1. Attach the thermister lug to the battery's negative post as shown in the
image at right. If the bank has multiple batteries connected in parallel,
mount the lug on the negative terminal closest to the center of the battery
bank.
2. Feed the Battery Temperature Sensor cable from the battery to the
regulator. The cable is 20' long to reach batteries located away from the
alternator and regulator.
3. Plug the positive (red) and negative (black) sensor leads into the Battery
Temperature Sensor terminal pins on the regulator (as indicated by the
BALMARr
legend on the side of the regulator). Use care to match polarity as
19009
61st Ave. NE #4
indicated. If only one Battery Temperature Sensor is used, ensure that the
Arlington,
WA 98223
sensor terminals are connected to the Battery #1 terminal pins at the
Phone:
360-435-6100
regulator.

You might also like