Scribd
Upload
41 views

Introduction To Physics 4

This document provides guidelines for writing a scientific report on an experiment. It explains the components of an experiment including the aim, variables (manipulated and responding), apparatus, procedure, data collection and tabulation, graphing, and analysis. The key steps are to state the aim, identify the variables, describe the apparatus and procedure, collect data in a table, plot a graph, determine the relationship between variables from the graph, and state any necessary precautions. The relationship is identified from the slope (gradient) and form (linear, inverse, direct) of the best-fit line or curve on the graphed data points.

Uploaded by

Suriyati Latip
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
41 views

Introduction To Physics 4

This document provides guidelines for writing a scientific report on an experiment. It explains the components of an experiment including the aim, variables (manipulated and responding), apparatus, procedure, data collection and tabulation, graphing, and analysis. The key steps are to state the aim, identify the variables, describe the apparatus and procedure, collect data in a table, plot a graph, determine the relationship between variables from the graph, and state any necessary precautions. The relationship is identified from the slope (gradient) and form (linear, inverse, direct) of the best-fit line or curve on the graphed data points.

Uploaded by

Suriyati Latip
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

1.

5 Scientific Investigation
When physicists observe a particular physical
phenomenon they will ask questions as to how
or why it happens. A hypothesis will be put forth
and experiments or scientific investigations will
be carried out to prove or disprove the
hypothesis. If the experiments bear out the
hypothesis, the hypothesis may come too
regarded as theory or law of nature. If they
dont the hypothesis will be rejected or
modified. In any experiment, the report on the
experiment will be based on these guidelines
and follows a sequence as shown in the
following flow chart:

Responding variable
The quantity whose values depend on the
manipulated variable or a secondary variable
which changes in response to the change in the
manipulated variable.

Fixed variable
The quantity whose value is kept constant
throughout the experiment.
Aim
A statement to show the investigation of the
variables involve.
The aim of the experiment should be written as:
To
investigate the
relationship
between
........and ..........
Apparatus
List the apparatus and materials used so that at
least a set of data for manipulated and
responding variables can be determined.
State the arrangement of the apparatus that
can function by drawing a labelling diagram.
Procedure
State the method of controlling the manipulated
variables.
State the method of measuring the responding
variables.
Repeat the experiments at least four times.
Tabulating the data

Inference
Early assessment that is carried out to answer
the questions raised.
The inference should be written as :
depend on.
Or
The ..changes as the
changes

Record the data in the following table


Manipulated
variable

Responding variable

Hypothesis
A general statement about the relationship
between a manipulated variable and a
responding variable.
The hyphotesis should be written as :
The greater the, the greater the.
Or
The bigger the., the smaller the..
Manipulated variable
The quantity whose values we deliberately
choose to change or a primary variable which
causes other secondary variable to change.

Analysing the data


Plot a graph of (Responding variable) against
(Manipulated variable)
How to tabulate the data?
The table must be neatly drawn and the data
arranged in either and rows.
The names and symbols of the manipulated and
responding variables must be written together
with the units.
For example,

Make sure the area covered by the


plotted points must not be less than 50% of the
area of the graph paper.

Velocity, v /
s
Time, t / s
Volume,
V/m3

Pressure,
Pa

P/

For example:

The scale on the axes must be uniform and


clearly marked with value. For example:

The data shown in the table must be consistent


in the number of decimal places in accordance
with the respective measuring instruments. For
example,
Length, l / cm
0
2
4
6
8

Time , t /s
12.8
25.6
39.4
52.2
75.0

If the data too small or too big use the standard


form number.
For example
Temperature,
T
10
20 30 40 50
(C)
Density,
9.7 8.5 7.3 6.6 5.1
(kgm-3)
x 104

All the points are marked with a symbol such as


a cross or circle and the centre of the cross
must accurately position.

The best straight line or the best curve graph


must be drawn.
The best straight line or the best curve graph is
the line that passes through most of the points
plotted such that it is balanced by the number
of points above and below the line. The line also
must
smooth.

How to plot the graph?


The title of the graph must be shown.
The axes of the graph must be labelled with the
unit used.
For example:

The scale chosen must be easy to use.


Scales such 1:1, 1:2, 1:5, 1:10, 1:100 are
preferred in plotting a graph.
Odd scales such as 1:3, 1:4, 1: 6, 1:7, 1: 30
should be avoided in plotting a graph.

It is not advisable to plot graph by joining point


to point because the graph obtained is not
smooth.

y is inversely proportional
to x

or y 1
or y = k

x
k = constant

How to analyse the data?


(a)
Determine the relationship between two
variables.
Example:

or y1 x1 = y2 x2

y is directly proportional to x.
or y x
or y = kx
k = constant
or y = mx m = gradient
or
y1 =
y2
x1
x2

(b)

or

or

Determine the gradient of the graph


Example

y increases linearly with x


y = mx + c
m = gradient
c = intercept on axis-y

y decreases linearly with x


y = -mx + c
m = gradient
c = intercept on axis-y

Draw a sufficiently large triangle to calculate


the gradient of the graph. State value of the
gradient with correct unit.
The gradient of the graph is
m

= y2 - y1
x2 - x1

(c)
graph.

Determine the certain values from the

Certain important values can be obtained from


the graph plotted by drawing a horizontal line or
by extrapolating the graph.

(d)

State the precautions should be taken


For example:
i.
ii.

Off the switch when taking the


reading of the ammeters.
Make sure the amplitude of
oscillation is small.

You might also like