BIE 5300/6300

Fall Semester 2004

Irrigation Conveyance & Control:

Flow Measurement & Structure Design

Lecture Notes

Biological & Irrigation Engineering Department

Utah State University, Logan, Utah

Gary P. Merkley

ii

BIE 5300/6300 Lectures

Preface
These lecture notes were prepared by Gary P. Merkley of the Biological &
Irrigation Engineering Department at USU for use in the BIE 5300/6300 courses. The
material contained in these lecture notes is the intellectual property right of G.P.
Merkley, except where otherwise stated.
Many thanks are extended to USU engineering students, past and present,
whose numerous suggestions and corrections have been incorporated into these
lecture notes.

Copyright Notice
This material has been duplicated by special permission of the copyright holder.
It is not to be duplicated or used for purposes other than learning resource support for
Utah State University. Any violation of this agreement is punishable under existing
copyright laws.
Copyright 2000, 2001, 2002, 2003, 2004

BIE 5300/6300 Lectures

iii

Gary P. Merkley

Gary P. Merkley

iv

BIE 5300/6300 Lectures

Contents
Page
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Course Introduction ........................................................................................... 1

Flumes for Open-Channel Flow Measurement ................................................ 19
Current Metering in Open Channels ................................................................ 35
Current Metering in Open Channels ................................................................ 45
Field Exercise #1 for Open-Channel Flow Measurement ................................ 57
Field Exercise #2 for Open-Channel Flow Measurement ................................ 59
Weirs for Flow Measurement ........................................................................... 61
Weirs for Flow Measurement ........................................................................... 73
Broad Crested Weirs ....................................................................................... 87
Broad Crested Weirs ....................................................................................... 95
Calibration of Canal Gates............................................................................. 107
Calibration of Canal Gates............................................................................. 123
Flow Measurement in Pipes........................................................................... 141
Flow Measurement in Pipes........................................................................... 153
Canal Design Basics...................................................................................... 161
Channel Cross Sections ................................................................................ 171
Design of Earthen Canals .............................................................................. 191
Sample Earthen Canal Designs..................................................................... 209
Canal Linings ................................................................................................. 221
Inverted Siphons............................................................................................ 229
Culvert Design & Analysis.............................................................................. 237
Sample Culvert Designs ................................................................................ 243
Culvert Hydraulic Behavior ............................................................................ 249
Flumes & Channel Transitions....................................................................... 257
Design Example for a Channel Transition...................................................... 265
Energy Dissipation Structures........................................................................ 275
Protective Structures ..................................................................................... 293
Safety Considerations.................................................................................... 301

BIE 5300/6300 Lectures

Gary P. Merkley

Gary P. Merkley

vi

BIE 5300/6300 Lectures

Units, Constants and Conversions

28.35 g/oz
15.85 gpm/lps (= 60/3.785)
7.481 gallons/ft3
448.86 gpm/cfs (= 7.481*60)
3.7854 litres/gallon
6.89 kPa/psi
1 cb = 1 kPa
10 mb/kPa, or 100 kPa/bar
2.308 ft/psi, or 9.81 kPa/m (head of water)
14.7 psi = 101.3 kPa = 10.34 m (head of water) = 1,013 mbar = 1 atm
62.4 lbs/ft3, or 1000 kg/m3 (max density of pure water at 4C)
0.1333 kPa/mmHg
1 ppm 1 mg/liter (usually)
1 mmho/cm = 1 dS/m = 550 to 800 mg/liter
0.7457 kW/HP
1 langley = 1 cal/cm2
0.0419 MJ/m2 per cal/cm2
0.3048 m/ft
1.609 km/mile
2.471 acre/ha
43,560 ft2/acre
1,233 m3/acre-ft
57.2958 degrees/radian
3.14159265358979323846
e 2.71828182845904523536
C = (F 32)/1.8
F = 1.8(C) + 32
Ratio of weight to mass at sea level and 45 latitude: g = 9.80665 m/s2

BIE 5300/6300 Lectures

vii

Gary P. Merkley

Gary P. Merkley

viii

BIE 5300/6300 Lectures

Lecture 1

Course Introduction
What is never measured is never managed
Rep. Stephen Urquhart (2003)
I. Textbook and Other Materials

The main references are Design of Small Canal Structures, USBR; and Water
Measurement Manual, USBR. At least one copy of each will be on reserve in the
library.
Some material will also be referred to from Irrigation Fundamentals, by
Hargreaves & Merkley, as well as from other books and sources
BIE 5300/6300 lecture notes by G.P. Merkley are required

II. Homework

All work must be organized and neat

There will be some computer programming and or spreadsheet exercises
Submitting work late:10% reduction per day, starting after class

III. Tests

One mid-term exam

Final exam is not comprehensive

IV. Subject Areas

Flow measurement
Open channels
Full pipe flow

Design of conveyance infrastructure

Canals, flumes, chutes
Canal linings
Siphons
Culverts
Energy dissipation structures

V. Why Measure Water?

Flow measurement is a key element in:
1. Water Management. Without knowing flow rates it is usually difficult to
quantify deliveries to water users, and in this case the evaluation of water
management practices is only vague
2. Water Quality Analysis. This relates to concentrations, rate of movement,
direction of movement, and dispersion of contaminants, and other issues
BIE 5300/6300 Lectures

Gary P. Merkley

3. Water Rights and Water Law. This includes volumetric delivery allotments,
groundwater pumping, and excess water (e.g. irrigation runoff), among others

Good quality, fresh water, is becoming more and

more scarce as people exploit water resources
more aggressively, and as the world population
increases
This increases the importance of water
measurement
It is unlikely that the regional and global situations
on water availability and water quality will improve
in the foreseeable future
When a resource is measured, it is implied that it
has significant value; when not measured, the
implication is of little or no value

Nilometer, Cairo, Egypt

VI. Some Fundamental Flow Measurement Concepts

Most flow measurement devices and techniques are based on the measurement
of head (depth or pressure) or velocity
One exception to this is the salt dilution method (described below)
Here, the term flow rate refers to volumetric rate, or volume per unit time
Thus, we apply mathematical relationships between head and discharge, or take
products of velocity and cross-sectional area
Strictly speaking, all open-channel and most pipe flow measurement techniques
cause head loss
The inability to make accurate measurements is not necessarily

because of instrumentation deficiencies, but is a fundamental

property of the physical world you cannot measure something
without changing it (paraphrased) W.K. Heisenberg (1901-76)

However, some methods incur negligible losses (e.g. ultrasonic)

It is usually desirable to have only a small head loss because this loss typically
translates into an increased upstream flow depth in subcritical open-channel flow
In open-channel flow measurement, devices can operate under free flow and
submerged flow regimes
In free flow, we are concerned with the upstream head because critical flow
occurs in the vicinity of the flow measurement device. As long as this is true,
changes in downstream depth will not affect discharge at that location.
In submerged flow, we are concerned with a head differential across the flow
measurement device.
In this class, the terms flow rate and discharge will be used interchangeably.

Gary P. Merkley

BIE 5300/6300 Lectures

VII. Flow Measurement Accuracy

Perhaps the most accurate method for measuring flow rate is by timing the filling
of a container of known volume
However, this is often not practical for large flow rates
Typical flow measurement accuracies are from 2% to 20% of the true
discharge, but this range can be much greater
Measurements of head, velocity, and area are subject to errors for a variety of
reasons:
1. Approach Conditions

High approach velocity

Approach velocity not perpendicular to measurement device

2. Turbulence and Eddies

Rough water surface

Swirling flow near or at measurement location

3. Equipment Problems

Staff gauges, current meters, floats,

etc., in disrepair
Shifting calibrations on pressure
transducers and other meters
Poor installation (non-horizontal
crest, wrong dimensions, etc.)

4. Measurement Location

Local measurements (uniform flow

assumption?)
Stream gauging stations (need
steady flow)

5. Human Errors

Misreading water levels, etc.

Misuse of equipment, or improper application of equipment

VIII. Simple Flow Measurement Methods

The following are considered to be special methods, because they are mostly
simple and approximate, and because they are not usually the preferred methods
for flow measurement in open channels

BIE 5300/6300 Lectures

Gary P. Merkley

Preferred methods are through the use of calibrated structures (weirs, flumes,
orifices, and others), and current metering
1. Measurement by Observation

In this method one must rely on experience to estimate the

discharge in an open channel, simply by observing the flow in
the channel and mentally comparing it to similar channels from
which the flow rate was measured and known
This method is usually not very accurate, especially for large
flows, but some very experienced hydrographers can (with
some luck) arrive at a close estimate

2. Measurement by Floats

The average flow velocity in an open channel can be estimated by measuring

the speed of a floating object on the surface of the water
This can be done by marking uniform distances along the channel and using
a watch to measure the elapsed time from a starting location to respective
downstream locations
However, in practice, usually only a single distance (say 10 m) is used

float
wa

te
r

su
r fa
ce

10 m

It is a good idea to have more than one measurement point so that the
velocity can be averaged over a reach, and to lessen the chance of an error
Then, a graph can be made of float travel distance versus time, with the slope
equal to the surface velocity of the water
Select a location in which the channel is fairly straight, not much change in
cross-section, smooth water surface, and no abrupt changes in bed elevation
or longitudinal slope
Note that wind can affect the velocity of the float, changing the relationship
between surface velocity and average flow velocity

Gary P. Merkley

BIE 5300/6300 Lectures

Care should be taken to obtain measurements with the float moving near the
center of the surface width of flow, not bumping into the channel sides, and
not sinking

The float speed will be higher than the average flow velocity in the channel,
unless perhaps the float travels near one of the channel banks or is
obstructed by vegetation
You can estimate the average velocity in the channel by reducing the float
speed by some fraction
The following table is from the U.S. Bureau of Reclamation
It gives coefficients to multiply by the measured float velocity, as a function of
average depth, to obtain the approximate average flow velocity in the channel

Average Depth
(ft)
(m)
1
0.30
2
0.61
3
0.91
4
1.22
5
1.52
6
1.83
9
2.74
12
3.66
15
4.57
>20
>6.10

Coefficient
0.66
0.68
0.70
0.72
0.74
0.76
0.77
0.78
0.79
0.80

To obtain average depth, divide the cross-sectional area by the top width of
the water surface (do not use an area-weighted average of subsection
depths)
The coefficients in the above table only give approximate results; you can
typically expect errors of 10 to 20% in the flow rate
What happens to the above coefficient values when the average water depth
is below 1 ft (or 0.3 m)?
Some hydrographers have used partially submerged wooden sticks which are
designed to approximate the mean flow velocity, precluding the need for
coefficients as in the above table
One end of the stick is weighted so that is sinks further

The stick will give the correct velocity only for a small range of water depths
The float method is not precise because the relationship between float speed
and true average flow velocity is not well known in general
Other methods should be used if an accurate measurement is desired

BIE 5300/6300 Lectures

Gary P. Merkley

Sample calculation:
The float method is applied in a rectangular channel with a base width of 0.94 m
and a uniform water depth of 0.45 m. Ten float travel times are recorded over a
distance of 5.49 m (18 ft), with calculated surface velocities:
Trial Time (s) V (m/s)
1
7.33
0.749
2
6.54
0.839
3
7.39
0.743
4
7.05
0.779
5
6.97
0.788
6
6.83
0.804
7
7.27
0.755
8
6.87
0.799
9
7.11
0.772
10
6.86
0.800
Avg:
7.02
0.783

Alternatively, the average surface velocity can be taken as 5.49/7.02 = 0.782

m/s, which is very close to the average velocity of 0.783 m/s from the above table
(as is usually the case). The surface velocity coefficient can be taken as 0.67,
interpolating in the previous table of USBR data, and the cross-sectional area of
the channel is (0.45)(0.94) = 0.42 m2. Then, the estimated flow rate is:
(0.67)(0.783 m/s)(0.42 m2) = 0.22 m3/s

3. Dye Method

The dye method, or color-velocity method, can be used to

measure the flow velocity, similar to the float method
However, in this method a slug of dye is injected into the
stream, and the time for the slug of dye to reach a downstream location is
measured
This time can be taken as the average of the time for the first portion of the
dye to reach the downstream location, and the time for the last portion of the
dye to reach that location (the dye will disperse and elongate as it moves
downstream).
The test section should not be too long, otherwise the dye will have dispersed
too much and it is difficult to visually detect the color differential in the water
Usually, it is appropriate to use a test section of approximately 3 m
Dyes used in this type of measurement should be nontoxic so as not to
pollute the water
Food coloring can be used, as can other colored chemicals, such as
flouricine

Gary P. Merkley

BIE 5300/6300 Lectures

4. Salt Dilution

In this method, an aqueous solution of known salt concentration, C1, is poured

into the stream at a constant rate, q
The completely mixed solution is measured at a downstream location,
providing the concentration C2
The downstream location should be at least 5 m (perhaps up to 10 or 15 m)
from the point of injection, otherwise incomplete mixing may result in large
errors; that is, you might measure a highly-concentrated slug of water, or you
might miss the slug altogether, if you try to measure too close to the point of
injection
After measuring the existing salt concentration in the flow (without adding the
concentrated solution), C0, the stream discharge, Q, can be calculated as,

t [QC0 + qC1] = t [(Q + q)C2 ]

(1)

C C2
Q = q 1

C2 C0

(2)

or,

The above two equations represent a mass balance, where: t can be in s

(doesnt really matter, because it cancels out); C can be in mg per liter; and q
and Q can be in lps
This method is not used to measure velocity, but total volumetric flow rate
Concentrations are normally expressed as mmho/cm, or dS/m

5. Uniform Flow

In this method the channel bed slope, average cross-section, and average
depth are measured
A roughness value is estimated, and the Manning or Chezy equation is
applied to calculate the discharge
This method is valid only for steady uniform flow, and is severely limited by an
inability to accurately estimate the roughness value
And because it is only valid for steady uniform flow, it cannot be
applied in general since these flow conditions are often not found
in open channels
Ideally, both bed slope and water surface slope are measured to
verify whether the flow is uniform or not
The discharge can be estimated by giving a range of probable flow
rates for maximum and minimum roughness values (also
estimated), based on the channel appearance and size
The roughness can be estimated by experience, or by consulting
hydraulics handbooks which provide tables and figures, or photographs

BIE 5300/6300 Lectures

Gary P. Merkley

6. Pitot Tube

A simple pitot tube can be

positioned into the flow to measure
the velocity head
One end of the tube is pointed into
the flow, and the other end is
pointed up vertically out of the water
both ends are open
The submerged end of the tube is positioned to be essentially parallel to the
flow
Solving for velocity in the equation for velocity head:

V = 2gh

(3)

This method is best applied for higher flow velocities because it is difficult to
read the head differential at low velocities, in which large errors in the
estimation of velocity can result

IX. Introduction to Flumes

Measurement flumes are open-channel

devices with a specially-shaped,
partially-constricted throat section
The flume geometry is often designed
to cause the flow regime to pass
through critical depth, providing a
means for determining the rate of flow
from a single (upstream) water depth measurement this is the advantage of a
free-flow regime
When the water surface exceeds specified limits, submerged-flow conditions
occur and two water depth measurements are required (upstream and
downstream)
In channels with small longitudinal bed slopes, it may be desirable to install a
flume to operate under conditions of submerged-flow rather than free flow in
order to:
1. reduce energy losses
2. place the flume on the channel bed to minimize the increase
in upstream water surface elevation
(the above two reasons are essentially the same thing)

Many different flow measurement flumes have been designed and tested, but
only a few are commonly found in practice today

Gary P. Merkley

BIE 5300/6300 Lectures

X. Flume Classifications
There are two principal classes of flumes: short-throated and long-throated
Short-throated flumes:

Critical flow conditions occur in regions of curvilinear flow (assuming the

regime is free flow)
These include flumes with side contractions and bottom contractions, and
some type of transition section
In general, laboratory calibrations are required to obtain flow coefficients
for rating
Under favorable operating conditions the discharge can be determined
with an accuracy of 2 to 5% for free flow

Long-throated flumes:

Critical flow conditions are created in a region of parallel flow in the control
section, again, assuming free flow conditions
These linear-stream flow conditions are much better theoretically defined;
thus, rating relations can be reasonably well predicted
Generally, flows larger than 10 lps can be measured with an error of less
than 2% in an appropriately dimensioned flume
Broad-crested weirs are an example of long-throated flumes

XI. Advantages and Disadvantages of Flumes

Advantages
1. capable of operation with relatively small head loss, and a high transition
submergence value (compared to sharp-crested weirs)
2. capable of measuring a wide range of free-flow discharges with relatively
high tail-water depths, using a single water depth measurement
3. capable of measuring discharge under submerged flow conditions using
two water depth measurements
4. both sediment and floating debris tend to pass through the structure
5. no need for a deep and wide upstream pool to reduce the velocity of
approach
Disadvantages
1. usually more expensive to construct than weirs
2. must be constructed carefully and accurately for satisfactory
performance
3. cannot be used as flow control structures (compared to adjustable weirs,
orifice gates, and other structures)
BIE 5300/6300 Lectures

Gary P. Merkley

4. often need to use standard design dimensions, unless you want to

develop your own calibration curve
XII. Free, Submerged, and Transitional Flow

When critical flow occurs the flow rate through the flume is uniquely
related to the upstream depth, hu
That is, the free flow discharge can be obtained with only a single water
depth measurement

Qf = f(hu )

(4)

When the tail-water depth is increased such that the flume operates under
submerged-flow conditions, both upstream, hu, and downstream, hd, depth
measurements are required.
Let S be the submergence ratio, or S = hd/hu. Then, Qs is a function of the
head differential, (hu - hd), and S

Qs = f(hu hd,S)

(5)

The value of submergence which marks the change from free flow to submerged
flow, and vice versa, is referred to as the transition submergence, St.
At this condition the discharge given by the free-flow equation is exactly
the same as that given by submerged-flow equation

XIII. Parshall Flumes

The Parshall flume is perhaps the most commonly used open-channel flowmeasuring device in irrigation systems in the U.S. and elsewhere
It was developed at Colorado State University by Ralph Parshall from 1915-1922
Some characteristics of this flume design are:
1. This flume has specially designed converging, throat and diverging
sections
2. It has been designed to measure flow from 0.01 to 3,000 cfs (1 lps to 85
m3/s), or more
3. Under typical conditions, free-flow accuracy is 5% of the true discharge
4. Under favorable conditions (calm upstream water surface, precise flume
construction, level upstream flume floor) free-flow accuracy can be 2%
of the true discharge
5. The head loss across a comparably-sized sharp-crested weir under freeflow conditions is roughly four times that of a Parshall flume operating
under free-flow conditions
6. It is usually designed to operate under free-flow conditions

Gary P. Merkley

10

BIE 5300/6300 Lectures

7. Size selection is based on the flume width which best fits the channel
dimensions and hydraulic properties
8. As a general rule, the width of the throat of a Parshall flume should be
about one-third to one-half the width of the upstream water surface in
the channel at the design discharge and at normal depth

The general forms of the free-flow and submerged-flow equations for flumes,
including the Parshall flume, are:
Free Flow

nf

Qf = Cf W (hu )

(6)

Submerged Flow

Qs =

Cs W(hu hd )nf

(7)

[ (log10 S + C2 )]ns

where nf and ns are the free-flow and submerged-flow exponents, respectively;

and W is the throat width.

It is strongly recommended that you use the same units for W and depth (hu and
hd) in Eqs. 6 and 7 (i.e. dont put W in inches and hu in feet)
Below are two views of a Parshall flume
Note that both hu and hd are measured from the upstream floor elevation, that is,
from a common datum
This is in spite of the fact that the downstream tap is supposed to be located at
an elevation equal to H Y below the upstream floor, as shown in the figure
below
The diverging outlet section of the flume is not required when the structure is
placed at a drop in bed elevation, whereby it would always operate under freeflow conditions
The USBR (1974) discusses modified Parshall flumes which fit a particular
canal profile
The following table gives dimensions (A-H, K, X & Y) and discharge ranges for
the 23 standard Parshall flume sizes (see the following figure showing the
dimensional parameters) in metric units

BIE 5300/6300 Lectures

11

Gary P. Merkley

Gary P. Merkley

12

BIE 5300/6300 Lectures

Parshall Flume Dimensions in metric units (see the above figure)

W (m)

0.025
0.051
0.076
0.152
0.229
0.305
0.457
0.610
0.762
0.914
1.219
1.524
1.829
2.134
2.438
3.048
3.658
4.572
6.096
7.620
9.144
12.192
15.240

0.167
0.214
0.259
0.394
0.575
0.845
1.026
1.207
1.391
1.572
1.937
2.302
2.667
3.032
3.397
4.756
5.607
7.620
9.144
10.668
12.313
15.481
18.529

0.093
0.135
0.178
0.394
0.381
0.610
0.762
0.914
1.067
1.219
1.524
1.829
2.134
2.438
2.743
3.658
4.470
5.588
7.315
8.941
10.566
13.818
17.272

C
0.363
0.414
0.467
0.621
0.879
1.372
1.448
1.524
1.632
1.676
1.829
1.981
2.134
2.286
2.438
4.350
4.972
7.772
7.772
7.772
8.084
8.395
8.395

D
0.356
0.406
0.457
0.610
0.864
1.343
1.419
1.495
1.600
1.645
1.794
1.943
2.092
2.242
2.391
4.267
4.877
7.620
7.620
7.620
7.925
8.230
8.230

Dimensions (m)
E
F
G
0.076
0.114
0.152
0.305
0.305
0.610
0.610
0.610
0.610
0.610
0.610
0.610
0.610
0.610
0.610
0.914
0.914
1.219
1.829
1.829
1.829
1.829
1.829

0.203
0.254
0.305
0.610
0.457
0.914
0.914
0.914
0.914
0.914
0.914
0.914
0.914
0.914
0.914
1.829
2.438
3.048
3.658
3.962
4.267
4.877
6.096

0.152
0.203
0.381
0.457
0.610
0.914
0.914
0.914
0.914
0.914
0.914
0.914
0.914
0.914
0.914
1.219
1.524
1.829
2.134
2.134
2.134
2.134
2.134

H
0.029
0.043
0.057
0.114
0.114
0.229
0.229
0.229
0.229
0.229
0.229
0.229
0.229
0.229
0.229
0.343
0.343
0.457
0.686
0.686
0.686
0.686
0.686

K
0.019
0.022
0.025
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.152
0.152
0.229
0.305
0.305
0.305
0.305
0.305

X
0.008
0.016
0.025
0.051
0.051
0.051
0.051
0.051
0.051
0.051
0.051
0.051
0.051
0.051
0.051
0.305
0.305
0.305
0.305
0.305
0.305
0.305
0.305

Q (m3/s)
min
max

Y
0.013
0.025
0.038
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.076
0.229
0.229
0.229
0.229
0.229
0.229
0.229
0.229

0.00028
0.00057
0.00085
0.00142
0.00283
0.0113
0.0142
0.0198
0.0227
0.0283
0.0368
0.0623
0.0736
0.116
0.130
0.170
0.227
0.227
0.283
0.425
0.425
0.566
0.708

0.0057
0.011
0.017
0.082
0.144
0.453
0.680
0.934
1.16
1.42
1.93
2.44
2.94
3.43
3.96
5.66
9.91
17.0
28.3
34.0
42.5
56.6
85.0

It is noted that Parshall flumes were developed using English units, but these
days we often prefer metric units
Anyway, many of the dimensions in English units were not even round
numbers, often being specified to the 32nd of an inch
The next table shows Parshall flume dimensions for the same 23 standard sizes,
but in feet, rounded to the thousandth of a foot, with discharge ranges in cubic
feet per second

BIE 5300/6300 Lectures

13

Gary P. Merkley

Parshall Flume Dimensions in English units (see the above figure)

W (ft)

0.083
0.167
0.250
0.500
0.750
1.000
1.500
2.000
2.500
3.000
4.000
5.000
6.000
7.000
8.000
10.000
12.000
15.000
20.000
25.000
30.000
40.000
50.000

0.549
0.701
0.849
1.292
1.885
2.771
3.365
3.958
4.563
5.156
6.354
7.552
8.750
9.948
11.146
15.604
18.396
25.000
30.000
35.000
40.396
50.792
60.792

0.305
0.443
0.583
1.292
1.250
2.000
2.500
3.000
3.500
4.000
5.000
6.000
7.000
8.000
9.000
12.000
14.667
18.333
24.000
29.333
34.667
45.333
56.667

1.190
1.359
1.531
2.036
2.885
4.500
4.750
5.000
5.354
5.500
6.000
6.500
7.000
7.500
8.000
14.271
16.313
25.500
25.500
25.500
26.521
27.542
27.542

1.167
1.333
1.500
2.000
2.833
4.406
4.656
4.906
5.250
5.396
5.885
6.375
6.865
7.354
7.844
14.000
16.000
25.000
25.000
25.000
26.000
27.000
27.000

Dimensions (ft)
E
F
G
0.250
0.375
0.500
1.000
1.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
2.000
3.000
3.000
4.000
6.000
6.000
6.000
6.000
6.000

0.667
0.833
1.000
2.000
1.500
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
6.000
8.000
10.000
12.000
13.000
14.000
16.000
20.000

0.500
0.667
1.250
1.500
2.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
3.000
4.000
5.000
6.000
7.000
7.000
7.000
7.000
7.000

H
0.094
0.141
0.188
0.375
0.375
0.750
0.750
0.750
0.750
0.750
0.750
0.750
0.750
0.750
0.750
1.125
1.125
1.500
2.250
2.250
2.250
2.250
2.250

K
0.063
0.073
0.083
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.500
0.500
0.750
1.000
1.000
1.000
1.000
1.000

0.026
0.052
0.083
0.167
0.167
0.167
0.167
0.167
0.167
0.167
0.167
0.167
0.167
0.167
0.167
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000

0.042
0.083
0.125
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.250
0.750
0.750
0.750
0.750
0.750
0.750
0.750
0.750

Q (cfs)
min
max
0.01
0.02
0.03
0.05
0.10
0.40
0.50
0.70
0.80
1.0
1.3
2.2
2.6
4.1
4.6
6.0
8.0
8.0
10
15
15
20
25

0.2
0.4
0.6
2.9
5.1
16.0
24.0
33.0
41.0
50.0
68.0
86.0
104
121
140
200
350
600
1000
1200
1500
2000
3000

The minimum flow rate values represent the limits of the validity of the free-flow
rating equation
For submerged flow conditions, a minimum flow rate also applies because if it is
very low, the difference between hu and hd will be virtually indistinguishable
(perhaps 1 mm or less)
The next table gives calibration parameters (Cf, Cs, nf, ns) and transition
submergence (St) for standard Parshall flume sizes (metric units)
Use Eq. (3) or (4) to get flow rate in m3/s, where depths are in metres
The C2 value in Eq. (4) is equal to about 0.0044 (dimensionless) for all of the
standard Parshall flume sizes
Standard sizes were developed in English units, so the throat width values show
below are odd numbers, but the ft-inch equivalents are given in parentheses
Note that St is transition submergence the value tends to increase with the size
of the flume, up to a maximum of about 0.80
Be aware that the St values in the table below are for the maximum flow rate; for
other flow rates it is different
Also note that the values in the table below are for a base 10 logarithm in Eq. (4)
In practice, under extreme submerged-flow conditions, the head differential, huhd, can be less than 1 mm and no measurement is possible with the flume

Gary P. Merkley

14

BIE 5300/6300 Lectures

Throat
Width (m)
0.025 (1)
0.051 (2)
0.076 (3)
0.152 (6)
0.229 (9)
0.305 (12)
0.457 (18)
0.610 (24)
0.762 (30)
0.914 (3)
1.219 (4)
1.524 (5)
1.829 (6)
2.134 (7)
2.438 (8)
3.048 (10)
3.658 (12)
4.572 (15)
6.096 (20)
7.620 (25)
9.144 (30)
12.192 (40)
15.240 (50)

Cf

Cs

nf

ns

St

2.38
2.38
2.32
2.50
2.34
2.26
2.32
2.34
2.36
2.37
2.40
2.43
2.46
2.49
2.49
2.47
2.43
2.40
2.37
2.35
2.33
2.32
2.31

2.10
2.15
2.14
2.02
1.91
1.76
1.71
1.74
1.70
1.70
1.66
1.65
1.62
1.61
1.59
1.52
1.50
1.48
1.46
1.45
1.44
1.43
1.42

1.55
1.55
1.55
1.58
1.53
1.52
1.54
1.55
1.56
1.56
1.57
1.58
1.59
1.60
1.60
1.59
1.59
1.59
1.59
1.59
1.59
1.59
1.59

1.000
1.000
1.000
1.080
1.060
1.080
1.115
1.140
1.150
1.160
1.185
1.205
1.230
1.250
1.260
1.275
1.275
1.275
1.275
1.275
1.275
1.275
1.275

0.56
0.61
0.64
0.55
0.63
0.62
0.64
0.66
0.67
0.68
0.70
0.72
0.74
0.76
0.78
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80

Metric Units

Parshall Flume Calibration Parameters for metric

units (depth and W in m, flow rate in m3/s)

The following table gives calibration parameters (Cf, Cs, nf, ns) and transition
submergence (St) for standard Parshall flume sizes in English units

BIE 5300/6300 Lectures

15

Gary P. Merkley

Throat
Width
1 inches
2 inches
3 inches
6 inches
9 inches
12 inches
18 inches
24 inches
30 inches
3 feet
4 feet
5 feet
6 feet
7 feet
8 feet
10 feet
12 feet
15 feet
20 feet
25 feet
30 feet
40 feet
50 feet

Cf

Cs

nf

ns

St

4.06
4.06
3.97
4.12
4.09
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.01
3.96
3.90
3.85
3.82
3.80
3.77
3.75

3.59
3.67
3.66
3.32
3.35
3.11
2.95
2.97
2.89
2.87
2.78
2.71
2.64
2.59
2.55
2.48
2.45
2.41
2.38
2.36
2.34
2.33
2.32

1.550
1.550
1.550
1.580
1.530
1.520
1.540
1.550
1.555
1.560
1.570
1.580
1.590
1.600
1.600
1.590
1.590
1.590
1.590
1.590
1.590
1.590
1.590

1.000
1.000
1.000
1.080
1.060
1.080
1.115
1.140
1.150
1.160
1.185
1.205
1.230
1.250
1.260
1.275
1.275
1.275
1.275
1.275
1.275
1.275
1.275

0.56
0.61
0.64
0.55
0.63
0.62
0.64
0.66
0.67
0.68
0.70
0.72
0.74
0.76
0.78
0.80
0.80
0.80
0.80
0.80
0.80
0.80
0.80

English Units

Parshall Flume Calibration Parameters for English

units (depth and W in ft, flow rate in cfs)

It is seen that nf, ns, and St are dimensionless, but Cf & Cs depend on the
units
Also, the submerged-flow coefficient, Cs, is for a base-10 logarithm
Note that, for 1 ft W 8 ft, the nf value can be approximated as:

nf 1.522 W 0.026

(8)

where W is in ft

For W > 8 ft, nf is constant, at a value of 1.59

For W > 8 ft, ns and St also remain constant at 1.275 and 0.80, respectively

Gary P. Merkley

16

BIE 5300/6300 Lectures

References & Bibliography

Abt, S.R., Florentin, C.B., Genovez, A., and Ruth, B.C. 1995. Settlement and Submergence
Adjustments for Parshall Flume. ASCE J. Irrig. and Drain. Engrg., 121(5):317-321.
Blaisdell, F.W. 1994. Results of Parshall Flume Tests. ASCE J. Irrig. and Drain. Engrg., 120(2):278291.
Brater, E.F., and King, H.W. 1976. Handbook of Hydraulics. McGraw-Hill Book Co., New York, N.Y.
Parshall, R.L. 1945. Improving the Distribution of Water to Farmers by Use of the Parshall Measuring
Flume. USDA Soil Conservation Service, in cooperation with the Colorado Agric. Exp. Station,
Colorado State Univ., Fort Collins, CO.
Parshall, R.L. 1953. Parshall Flumes of Large Size. USDA Soil Conservation Service, in cooperation
with the Colorado Agric. Exp. Station, Colorado State Univ., Fort Collins, CO.
Skogerboe, G.V., Hyatt, M.L., and Eggleston, K.O. 1967. Design & Calibration of Submerged Open
Channel Flow Measurement Structures, Part 1: Submerged Flow. Utah Water Research
Laboratory, Utah State Univ., Logan, UT.
Skogerboe, G.V., Hyatt, M.L., and Eggleston, K.O. 1967. Design & Calibration of Submerged Open
Channel Flow Measurement Structures, Part 2: Parshall Flumes. Utah Water Research
Laboratory, Utah State Univ., Logan, UT.
USBR. 1997. Water Measurement Manual. U.S. Bureau of Reclamation, Denver, CO. (also available
from Water Resources Publications, LLC, http://www.wrpllc.com/)
Wright, S.J., and Taheri, B. 1991. Correction to Parshall Flume Calibrations at Low Discharges.
ASCE J. Irrig. and Drain. Engrg., 117(5):800-804.

BIE 5300/6300 Lectures

17

Gary P. Merkley

Gary P. Merkley

18

BIE 5300/6300 Lectures