BURNHAM HEATING HELPER TABLE OF CONTENTS

1. STEAM 10. VENTING FLUE PROD-

Two Pipe Steam (Sizing) ......... 2 UCTS
One Pipe Steam (Sizing) ........... 3 Acceptable Venting Material . 6 7
Relevant Information to Steam Specific Metal Vents ................ 6 8
Piping ....................................... 4 Venting Catagories: Gas Heating
Steam Boiler Piping Schematics Equipment ............................. 6 9
11 11. BASIC ELECTRICITY FOR
Converting a Steam System HEATING
to Hot Water ........................ 2 0 Units of Electrical Measurement7 0
2. HOT WATER PIPING - RES. Direct & Alternating Currents7 0
Pipe Capacity Chart ................ 2 4 Motors ....................................... 7 1
System Purge Piping ................ 2 5 Transformers ............................ 7 1
Indirect D.H.W Piping (Tankless) Relays ........................................ 7 1
27 Switches ..................................... 7 3
Indirect Swimming Pool Heating Overload Protection ................ 7 3
28 Electrical Service ..................... 7 3
Hot Water System Air Cushion/ 12. HEATING INDUSTRY
A/R........................................30 ACRONYMS
Boiler By-Pass Piping ............. 3 1 Building Codes & standards .... 7 4
3. DOMESTIC HOT WATER 3 9 Professional Associations
4. INSTALLED RADIATION and Societies .......................... 7 4
DETERMINING HEAT LOAD Approval Agencies .................. 7 5
Sizing Obsolete Radiation ....... 4 2 13. METRIC SYSTEM ........... 7 6
Sizing Convectors .................... 4 5 14. MISCELLANEOUS
Correction Factors ................... 4 7 Energy Terms - Conversions -
Sizing Pipe Coils ...................... 4 7 Heat Values ............................ 8 5
Sizing Bare Pipe Measuring Gas Oil Input .......... 8 7
(Cast Iron/Copper) .............. 48 Acidity and Alkalinity (ph)
Sizing Insulated Pipe ................ 4 9 Measures ................................ 9 0
5. WATER CONTENT Sound Levels ............................. 9 0
Radiation ................................... 5 0 Gas Pipe Sizing ......................... 9 1
Steel and Wrought Iron Pipe Correction Factors for Specific
(std. wt.) ................................. 5 0
Copper Tubing (Type L) ........ 5 0 Gravity Other Than 0.60 ... 9 2
Water Conversion Factors ..... 5 0 Heating Abbreviations ............. 9 3
6. HEAT LOSS CALCULATION Tank Capacities ....................... 9 4
Short Form Survey ................... 5 1 Heating Air - Melting Metals . 9 6
Greenhouse Calculation ........... 5 2 Equivalent Values of
7. FUEL CONSUMPTION & Heating Units ........................ 9 8
ENERGY COST Standard Symbols in Heating
Degree Day Method ................ 5 5 Specifications ............................ 9 9
Hydronic vs. Warm Air (Gas/Oil) 15. BURNHAM PRODUCT
59 REVIEW ................................. 100
8. VALVES (TYPES Venting Guide for Burnham Gas
AND APPLICATION) ......... 61 Boilers ...................................... 111
9. STANDARD SYMBOLS 16. HOME HEATING
USED IN HEATING DRAW- TEAM ....................................... 112
INGS ......................................... 6 3

1
 CHAPTER 1 - STEAM

ONE AND TWO PIPE SYSTEMS - MAINS AND RISERS

The steam system piping recommendations that follow are designed to
help guide an individual working on existing systems; systems that may
require alterations or additions for a variety of reasons. These recommen-
dations are conservative but in light of many unknown variables, they will
serve one well.
TWO PIPE STEAM
1. STEAM MAIN Capacity in Sq. Ft. E.D.R.

Size of Pipe Distance of Main

in In. 100' 200' 300'
2 650 461 375
2-1/2 1,030 731 595
3 1,860 1,320 1,075
4 3,800 2,698 2,196
6 11,250 7,987 6,502
8 22,250 15,797 12,860
10 40,800 28,968 23,582
12 66,000 46,860 38,148
Note: Mains must be pitched for steam & condensate to flow in same direction.

2. STEAM RISERS
Maximum Capacity (Sq. Ft. E.D.R.) at Various Riser Pitch With
Steam and Condensate Flowing in Opposite Direction.
Pipe Size Pitch of Pipe per 10' Length
in In. 1" 2" 3" 4" 5"
3/4 22.8 28.4 33.2 38.6 42.0
1 46.8 59.2 69.2 76.8 82.0
1-1/4 79.6 108.0 125.2 133.6 152.4
1-1/2 132.0 168.0 187.2 203.2 236.8
2 275.2 371.6 398.4 409.6 460.0
Note: Above E.D.R. is maximum. Greater load will cause problems with increased
steam velocities.

3. CONDENSATE RETURN MAINS (Horizontal, Pitched)

Capacity based on sq. ft. E.D.R. (2 oz PD per 100')
Pipe Size in In. Dry Return Wet Return
1 370 900
1-1/4 780 1,530
1-1/2 1,220 2,430
2 2,660 5,040
2-1/2 4,420 8,460
3 8,100 13,500
4 17,380 27,900
2
 CHAPTER 1 - STEAM

4. CONDENSATE RETURN RISERS (Vertical, Horizontal Pitch)

Capacity Based on Sq. Ft. (E.D.R.) (2 oz. PD per 100')
Pipe Size Dry Return
3/4" 170
1" 410
1¼” 890
1½” 1,350

ONE PIPE STEAM

1. STEAM MAIN
Capacity in Sq. Ft. (E.D.R.) (Based on 2 oz. PD)
Pipe Size T.E.L. T.E.L.
Inches 100' 200'
2" 350 235
2½” 580 385
3" 1,050 700
4" 2,210 1,480
6" 6,880 4,480
Notes: Mains must be pitched for steam & condensate to flow in same
direction. If steam and condensate counterflows, increase piping one
size.

2. STEAM RISER - Capacity in Sq. Ft. (E.D.R.)

(Up-feed Riser - Horizontal Travel
8' Max. - Riser Not Dripped) TO RADIATOR

Pipe Size Sq. Ft.

Inches E.D.R.
1" 25 PITCH 1/2" PER FT.
A
1¼” 55 TO RADIATOR
OR RISER
1½” 85
B
2" 150 PITCH 1/2" PER FT.

DRIP TO WET RETURN

Notes:
(A) Horizontal travel beyond 10' increase one size
(B) Horizontal travel sloped down and dripped decrease one size

3
 CHAPTER 1 - STEAM

3. DRY RETURN - Capacity in Sq. Ft. (E.D.R.)

Pipe Size Sq. Ft. (E.D.R.)
1-1/4” 640
1-1/2” 1,000
2" 2,180

4. WET RETURN - Capacity in Sq. Ft. (E.D.R.)

Pipe Size Sq. Ft. (E.D.R.)
1-1/4” 1,100
1-1/2” 1,700
2" 3,600

NUMBER OF SMALLER PIPES EQUIVALENT TO ONE LARGER PIPE

PIPE PIPE SIZE

SIZE 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 5" 6"
1/2" 1 2.27 4.88 10 15.8 31.7 52.9 96.9 140 205 377 620
3/4" 1 2.05 4.3 6.97 14 23.2 42.5 65 90 166 273
1" 1 2.25 3.45 6.82 11.4 20.9 30 44 81 133
1-1/4" 1 1.5 3.1 5.25 9.1 12 19 37 68
1-1/2" 1 2 3.34 6.13 9 13 23 39
2" 1 1.67 3.06 4.5 6.5 11.9 19.6
2-1/2" 1 1.82 2.7 3.87 7.12 11.7
3" 1 1.5 2.12 3.89 6.39
3-1/2" 1 1.25 2.5 4.25
4" 1 1.84 3.02
5" 1 1.65
6" 1

STEAM VELOCITIES IN STEAM PIPING

To obtain steam velocity in feet per second, multiply load by proper factor shown below.

Initial PIPE SIZE - INCHES

Pressure
of Dry Steam 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 4" 5" 6" 8" 10" 12"
5 PSI
.1000 .0610 .0425 .0276 .0160 .0101 .0071 .0041 .0026 .00182
Gauge
Sq. Ft.
2 PSI
EDR .2750 .1580 .1170 .0700 .0490 .0320 .0186 .0118 .0082 .0047 .0030 .0021
Gauge
Factor
0 PSI
.3094 .1778 .1316 .0788 .0551 .0360 .0209 .0133 .0093 .0054 .0034 .0024
Gauge

4
 FRICTION LOSSES - FLOW OF STEAM THROUGH PIPES
Based On: Dry Steam at 2PSI Gauge Initial Friction Losses: Are in ounces per 100 linear feet
Pressure. Schedule 40 Steel Pipe. of pipe, or the equivalent.
Loads: Are in Sq. Ft. EDR. For Capacities In Pounds Per Hour: Divide Sq. Ft.
EDR by 4.
PRESSURE LOSS OUNCES - PER 100 FEET OF STEEL PIPE
LOAD
SQ. FT. PIPE SIZE - INCHES
EDR 3/4" 1" 1¼" 1½" 2" 2½" 3" 4"
30 0.80
35 1.05
40 1.31
45 1.62
50 1.95 .60
75 4.01 1.21
100 6.7 2.05 .54
125 10.2 3.07 .80
150 14.3 4.27 1.12 .54
175 18.9 5.7 1.48 .70
200 24.3 7.2 1.88 .89
225 9.0 2.33 1.11
250 10.9 2.83 1.33
275 13.2 3.35 1.59
300 15.4 3.92 1.86
350 20.6 5.2 2.47
400 26.5 6.7 3.15 .92
450 8.3 3.90 1.14
500 10.0 4.75 1.38
550 12.0 5.6 1.64
600 14.1 6.6 1.91
650 16.4 7.7 2.22
700 19.0 8.8 2.55 1.06
800 24.4 11.4 3.27 1.35
900 14.1 4.05 1.68
1000 17.2 4.93 2.04
1100 20.6 5.9 2.43
1200 24.3 6.9 2.85
1300 28.3 8.1 3.32 1.14
1400 9.3 3.81 1.30
1500 10.6 4.31 1.48
1600 11.9 4.89 1.66
1700 13.4 5.5 1.86
1800 14.9 6.1 2.07
1900 16.6 6.8 2.28
2000 18.2 7.5 2.51
2200 21.8 8.9 3.00
2400 25.8 10.6 3.53
2600 12.3 4.08 1.08
2800 14.1 4.73 1.24
3000 16.1 5.4 1.40
3200 18.2 6.1 1.58
3500 21.6 7.2 1.86
4000 27.9 9.2 2.41
4500 11.5 2.98
5000 14.1 3.62
5500 16.9 4.34
6000 20 0 51

5
 CHAPTER 1 - STEAM

PROPERTIES OF SATURATED STEAM

Specific
Heat in BTU/lb. Volume
Pressure Temp Cu. ft.
psig °F Sensible Latent Total per lb.
25 134 102 1017 1119 142
Inches Vac

20 162 129 1001 1130 73.9

15 179 147 990 1137 51.3
10 192 160 982 1142 39.4
5 203 171 976 1147 31.8
0 212 180 970 1150 26.8
1 215 183 968 1151 25.2
2 219 187 966 1153 23.5
3 222 190 964 1154 22.3
4 224 192 962 1154 21.4
5 227 195 960 1155 20.1
6 230 198 959 1157 19.4
7 232 200 957 1157 18.7
8 233 201 956 1157 18.4
9 237 205 954 1159 17.1
10 239 207 953 1160 16.5
12 244 212 949 1161 15.3
14 248 216 947 1163 14.3
16 252 220 944 1164 13.4
18 256 224 941 1165 12.6
20 259 227 939 1166 11.9
22 262 230 937 1167 11.3
24 265 233 934 1167 10.8
26 268 236 933 1169 10.3
28 271 239 930 1169 9.85
30 274 243 929 1172 9.46
32 277 246 927 1173 9.10
34 279 248 925 1173 8.75
36 282 251 923 1174 8.42
38 284 253 922 1175 8.08
40 286 256 920 1176 7.82
42 289 258 918 1176 7.57
44 291 260 917 1177 7.31
46 293 262 915 1177 7.14
48 295 264 914 1178 6.94
50 298 267 912 1179 6.68
55 300 271 909 1180 6.27
60 307 277 906 1183 5.84
65 312 282 901 1183 5.49
70 316 286 898 1184 5.18
75 320 290 895 1185 4.91
80 324 294 891 1185 4.67
85 328 298 889 1187 4.44
90 331 302 886 1188 4.24
95 335 305 883 1188 4.05
100 338 309 880 1189 3.89
105 341 312 878 1190 3.74
110 344 316 875 1191 3.59

6
 CHAPTER 1 - STEAM

RELATIONS OF ALTITUDE,
PRESSURE & BOILING POINT

Atmospheric Boiling Point of Water °F

Pressure Absolute (Gage Pressure PSI)
Inches of Lbs.
Altitude Mercury per
Feet (Barometer) Sq. In. 0 1 5 10 15
-500 30.46 14.96 212.8 216.1 227.7 239.9 250.2
-100 30.01 14.74 212.3 215.5 227.2 239.4 249.9
Sea Level 29.90 14.69 212.0 215.3 227.0 239.3 249.7
500 29.35 14.42 211.0 214.4 226.3 238.7 249.2
1000 28.82 14.16 210.1 213.5 225.5 238.1 248.6
1500 28.30 13.90 209.4 212.7 225.0 237.6 248.2
2000 27.78 13.65 208.2 211.7 224.1 236.8 247.7
2500 27.27 13.40 207.3 210.9 223.4 236.3 247.2
3000 26.77 13.15 206.4 210.1 222.7 235.7 246.7
3500 26.29 12.91 205.5 209.2 222.1 235.1 246.2
4000 25.81 12.68 204.7 208.4 221.4 234.6 245.7
4500 25.34 12.45 203.7 207.5 220.7 234.0 245.2
5000 24.88 12.22 202.7 206.8 220.1 233.4 244.7
6000 23.98 11.78 200.9 205.0 218.7 232.4 243.8
7000 23.11 11.35 199.1 203.3 217.3 231.3 242.9
8000 22.28 10.94 197.4 201.6 216.1 230.3 242.0
9000 21.47 10.55 195.7 200.0 214.8 229.3 241.3
10000 20.70 10.17 194.0 198.4 213.5 228.3 240.4
11000 19.95 9.80 192.2 196.8 212.3 227.3 239.6
12000 19.23 9.45 190.6 195.2 211.1 226.3 238.7
13000 18.53 9.10 188.7 193.6 209.9 225.4 237.9
14000 17.86 8.77 187.2 192.3 208.8 224.5 237.2
15000 17.22 8.46 185.4 190.6 207.6 223.6 236.4

7
 CHAPTER 1 - STEAM

EXPANSION OF PIPES IN INCHES PER 100 FT

Temp. Cast Wrought Brass or

Degrees F. Iron Iron Steel Copper
0 0.00 0.00 0.00 0.00
50 0.36 0.40 0.38 0.57
100 0.72 0.79 0.76 1.14
125 0.88 0.97 0.92 1.40
150 1.10 1.21 1.15 1.75
175 1.28 1.41 1.34 2.04
200 1.50 1.65 1.57 2.38
225 1.70 1.87 1.78 2.70
250 1.90 2.09 1.99 3.02
275 2.15 2.36 2.26 3.42
300 2.35 2.58 2.47 3.74
325 2.60 2.86 2.73 4.13
350 2.80 3.08 2.94 4.45

8
 CHAPTER 1 - STEAM

STEAM SUSPENDED UNIT HEATERS/UNIT VENTILATORS

Output is normally based on 2PSI steam/60° entering air.

Output will increase or decrease with changes in steam pressure and/or
entering air.
FOR CONVERSION OF BASIC STEAM RATINGS
FACTORS @ 2 lbs. ga./60 deg. entering air to various conditions of
steam pressure and air temperature
STEAM ENTERING AIR TEMP. DEG. F.
lbs.
per
sq. Temp l. heat
in ºF Btu/lb. -10 0 10 20 30 40 50 60 70 80 90 100
0 212.0 970.2 1.19 1.11 1.03 .96 .88 .81 .74 .67
2 218.5 966.2 1.32 1.24 1.16 1.08 1.00 .93 .85 .78 .71
5 227.2 960.5 1.64 1.55 1.46 1.37 1.29 1.21 1.13 1.05 .97 .90 .83 .76
10 239.4 952.5 1.73 1.64 1.55 1.46 1.38 1.29 1.21 1.13 1.06 .98 .91 .84
15 249.7 945.5 1.80 1.71 1.61 1.53 1.44 1.34 1.28 1.19 1.12 1.04 .97 .90

Note: If it is found that operting conditions create a final air

temperature below 90°, the output air stream may be uncomfortable
and steam pressure should be increased.

Problem: Condensate will increase. How much?

Example: A unit heater rated at 100,000 btuh (2 psi/60° e.a.) is

installed with 50° entering air but final air temperature is below 90°.

Factory Rating: 100,000 btuh ÷ 966.2 (latent heat at 2 psi) = 103.5

lbs. per hr.

Operating Conditions: 100,000 x 1.08 (50° e.a.) ÷ 966.2 = 111.8 lbs.

per hr.

Increasing pressure to 5 psi: 100,000 x 1.13 ÷ 960.5 = 117.7 lbs.

per hr.

9
 CHAPTER 1 - STEAM

STEAM CONVERSION FACTORS

MULTIPLY BY TO GET
• Boiler Horsepower (BHP) 34.5 Lb. of Steam
Water per hour (lb/hr)
• Boiler Horsepower (BHP) 0.069 Gallons of Water Per
Minute (GPM)
• Sq. Feet of Equivalent Direct 0.000637 Gallons of Water per
Radiation (EDR) Minute(GPM)
• Boiler Horsepower (BHP) 33,479 B.T.U.
• Boiler Horsepower (BHP) 108 Sq. Feet of Equivalent
Direct Radiation (EDR)
• Lbs. of Steam Water 0.002 Gallons of Water per
per Hour (lb/hr) Minute(GPM)
• Lbs. per square inch 2.307 Feet of Water
• Lbs. per square inch 2.036 Inch of Mercury
• Feet of Water (head) 0.4335 Lbs. per square inch
• Inch of Mercury 13.6 Inch of Water Column
• Gallons of Water 8.34 Lbs. of Water
• Cubic Feet of Water 7.48 Gallons of Water
• Cubic Feet per Minute 62.43 Lbs. of Water per Minute
• Cubic Feet per Minute 448.8 Gallons per hour
• Cubic Centimeters per 1,400 Parts per billion of Oxygen
ltr. of Oxygen
• Lbs. of Condensate 4 Sq. ft. E.D.R.

Note: Use above factors to match condensate return and boiler feed
equipment with boiler size.

• Size Condensate Receivers for 1 min. net storage capacity based on

return rate.
• Size Boiler Feed Receivers for system capacity (normally estimated
at 10 min.)
• Size Condensate Pumps at 2 to 3 times condensate return rate.
• Size Boiler Feed Pumps at 2 times boiler evaporation rate or .14
GPM/boiler HP (continuous running boiler pumps may be sized at
1-1/2 times boiler evaporation rate or .104 GPM/boiler HP)

10
 CHAPTER 1 - STEAM

STEAM PIPING BOILER DETAIL

A. Steam: Gravity Return

Boiler: One Riser

Boiler: Multiple Risers

11
 CHAPTER 1 - STEAM

A. 24" vertical rise.

B. Horizontal traverse to line up header with rear return tapping.
C. Vertical rise to existing main. Same size as header.
D. Nipple: 6" residential; 12" commercial.
E. Hartford Loop. Height/size, consult manufacturer.
F. Preferable use plugged tees in lieu of 90° elbow in wet returns.
G. Header all steam risers before moving steam to system.

12
 CHAPTER 1 - STEAM

B. Steam: Pump Return

Single Boiler

Notes refer to Single & Multiple Boilers

A. Header drip. Use in lieu of Hartford Loop when pump
returns condensate. Size same as equalizer. May reduce
below W.L.
B. Install check valve. Preferably lift check in lieu of swing.
C. Install F & T trap in header drip at N.W.L. Will maintain
proper water level in unfired boilers. Return overflow to
condensate receiver.
D. Multiple boilers with common boiler feed system must
have each boiler return isolated with motorized valves.
E. Initial call for steam may create excess condensate in
common drop header. F & T trap will safely guide
condensate to condensate receiver.
F. Thermostatic trap piped from header to F & T will help
remove air from header.
G. Size motorized valve by GPM flow. Increase pipe size
between solenoid and boiler to reduce water velocity into
boiler. See recommendations for water flow on condensate
pump piping detail.
H. See pump piping detail for condensate return to boiler.
J. Plug valves must be installed next to each motorized valve to
regulate GPM flow to each boiler from common pumping.
13
 CHAPTER 1 - STEAM

Multiple Boilers

14
 CHAPTER 1 - STEAM

STEAM PIPING - PUMP DETAIL

A. Condensate Pump

15
 CHAPTER 1 - STEAM

B. Boiler Feed Pump and Condensate Pump

Control of Combination Units

• Condensate Unit. Float mechanism in receiver operates pump. It will
move water to the boiler feed receiver.
• Boiler Feed Unit. Pump Controller (#150/42A McDonnell-Miller are
typical) will control the movement of water directly to the boiler.
Should the water in the boiler feed receiver drop too low, an installed
water make-up valve will raise the receiver to a safe level.
16
 CHAPTER 1 - STEAM

C. Boiler Feed and Vacuum Pumps

Control & Pipe (same as Boiler Feed & Condensate Pump)

Additional Piping: Equalizing line between boiler steam header and
vacuum pump. Equalizing line will prevent a possible vacuum develop-
ing in steam supply that could be greater than vacuum in the return.

17
 CHAPTER 1 - STEAM

SIZING OF VACUUM PUMP

Vacuum condensate pumps are normally sized at 2 or 3 times the system

condensing rate. This is the same procedure for sizing standard condensing
rate. The vacuum pump must also remove air from the return system.
The system size, the inches of vacuum desired, and tightness of the system
piping must be considered. The following chart will help.

Air Removal Requirements

System Vac/In. Hg. CFM/1,000 EDR

• up to 10,000 EDR 0-10 .5
(tight)
• over 10,000 EDR 0-10 .3
(tight)
• all systems, some 0-10 1.0
air in-leakage

HIGHEST TEMPERATURE °F OF CONDENSATE

PERMISSIBLE WITH VACUUM PUMPS

Vacuum Inches Highest Permissible

of Mercury Temperature of
in Pump Receiver Condensate °F
15 179
12 187
10 192
8 196
6 201
4 205
2 209
1 210

18
 CHAPTER 1 - STEAM

STEAM PIPING CHEMICAL FEED TO BOILER

Placement of Chemical Feed to Boiler

• Between boiler and boiler feed pump.

• Chemical treatment added ahead of the pump suction will increase
the
friction and shorten the life of the mechanical pump seals.

Procedure
• Open valve (3).
• Pour chemicals into funnel to rest in receptacle.
• Close valves (1) - (3) - (5); open valves (2) - (4). Condensate will
move
from the pump through the receptacle and take the chemicals to the
boiler.
• When feeding is complete, close valves (2) and (4), thenopen valve
(1).
• Residue in receptacle may be drained by opening valve (5).
19
 CHAPTER 1 - STEAM

CONVERTING A STEAM SYSTEM TO HOT WATER

GUIDELINES

1. If the heat emitters are cast iron radiators make certain that the
sections are nippled (connected) at both the top and bottom.

2. Size boiler based on a calculated heat loss not installed radiation.

3. Measure the installed radiation. Divide total E.D.R. (sq. ft.) into
the calculated heat loss. The answer will indicate the number of BTU's
each sq. ft. of radiation must develop at outdoor design temperature.

Refer to the chart on page 22. In the BTU column move horizontally
to the number nearest your calculation. Above that number will be the
maximum system temperature you need. Vertically below will be the
amount of radiation (sq. ft.) that the various pipe sizes will handle.

4. One-Pipe Steam System: Existing steam mains and risers may

be reused. However, new return risers and return main must be
installed. Use the chart on page 13 to determine their size.

5. Two-Pipe Steam System: With the exception of the near boiler

piping, all the system piping (steam mains, risers, and condensate
returns) may be reused. Typically, a residential steam system that has
2" steam mains will have a minimum 1 1/4" dry return. If the heat
loss is less than the 160 MBH that 1 1/4" dry return would be of
sufficient size. The chart on page 13 gives the MBH capacity of pipe
sizes from 1/2" to 2".

6. Regardless of the system, never reuse existing wet return piping.

20
 CHAPTER 1 - STEAM

ONE PIPE STEAM (Figure 1)

Steam
Air
Vent

STEAM

Manual
Hot Water
CONVERTED TO Air Vent

HOT WATER Balancing

Valve

NOTE: Radiator must be nippled top & bottom.

21
 CHAPTER 1 - STEAM

TWO PIPE STEAM (Figure 2)

STEAM

Manual
Air
Vent

CONVERTED TO Remove
HOT WATER Thermostatic
Disc

22
 CHAPTER 1 - STEAM

Capacity
Basis: 70°F Room Temperature 20°F Temperature Drop
Sq. Ft. Radiation
Temp. 215° 200° 190° 180° 170° 160° 150° 140° 130° 120° 110°

BTU 240 210 190 170 150 130 110 90 70 50 30

Pipe
MBH
Size

1/2" 17 71 81 90 100 113 131 155 189 243 340 567

3/4" 39 163 186 205 229 260 300 355 433 557 780 1300
1" 71 296 338 374 418 473 546 646 789 1014 1420 2367
1 1/4" 160 667 762 842 914 1067 1231 1455 1778 2286 3200 5333
1 1/2" 240 1000 1143 1263 1412 1600 1846 2182 2667 3429 4800 8000
2" 450 1875 2143 2368 2647 3000 3462 4091 5000 6429 9000 15000
Use chart to determine BTU load on radiation converted from steam to H.W.
Note: Heat loss of building will determine BTU load on system piping.
Divide sq. ft. of installed radiation into heat loss = BTU load per sq. ft.

23
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

Pipe Capacity in MBH

at 500 Milinches Restriction Per Foot of Pipe

+Friction Velocity Flow of Water

Pipe Head Feet G.P.M. at Inches Per Ft. Per
Size MBH Per 100' 20° T.D. Sec. Min.
1/2" 17 4.2' 1.7 23 115
3/4" 39 4.2' 3.9 27 135
1" 71 4.2' 7.1 34 170
1-1/4" 160 4.2' 16.0 40 200
1-1/2" 240 4.2' 24.0 *45 225
2" 450 4.2' 45.0 *54 270
2-1/2" 750 4.2' 75.0 *62 310
3" 1400 4.2' 140.0 *72 360
4" 2900 4.2' 290.0 *80 400

* - Maximum velocity flow

+ - In order for a pump to move the G.P.M. listed, the pump must
overcome a friction head of 4.2 feet per 100' of pipe travers.
(Total Equivalent Length)

Example: If one wants to carry 16 gpm in a 1-¼" pipe through a pipe

circuit of 300' (T.E.L.), the pump must overcome a friction head of 4.2'
x 3 or 12.6 ft. In other words, the pump specification would be to pump
16 gpm against a 12.6 friction head.

24
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

SYSTEM PURGE IN LIEU OF AIR VENTS

(A) Separate ½” C.W.S. with Globe valve or by-pass P.R.V.

(B) Ball valve: optional but preferred
(C) Ball valve
(D) Hose bib (for purging)
(E) Zone valves or ball valves

25
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

SYSTEM PURGE IN LIEU OF AIR VENTS

APPLICATION
Any series loop piping, especially where system high points may be
con- cealed or venting is impractical. “System purge” is designed to
remove air initially from the piping system, especially the high points.

GUIDELINES
After the initial removal of air it is important for the system to be
able to handle air that will develop when the system water is heated.
Installation of an air scoop or an in-line airtrol at the boiler supply will
be necessary to either vent the air from the system or direct the air to
a standard expansion tank.

A system purge is recommended only on Series Loop Installations. If

other than non-ferrous baseboard is used, such as Base-Ray, the
interconnecting pipe will purge but vents must be placed on each free
standing assembly of
Base-Ray.

PROCEDURE
1. Fill system with water. Isolate boiler by closing valves (B) and
(C).
2. Begin purge by opening first zone or loop. Next, open valve (A)
(cold water supply). Finally and immediately, open hose bib (D).
Once water flows freely, close the first zone or loop and then do
the same for the remaining zones or loops.

26
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

INDIRECT DOMESTIC HOT WATER PIPING

1. APPLICATION
A. Tankless Heater: Piping below is essential for safe and reliable
operation.
B. Storage Heater: If the storage water temperature is maintained at
or below 120°F, piping below is unnecessary.
If there is need to increase the storage, this can be accomplished
by storing hotter water then tempering it. This will necessitate
the piping below.
2. PIPING SCHEMATIC

(1) Preferably the mixing valve should be set no higher than 120°F.
Install mixing valve 15" below H.W. outlet. This will create a
beneficial cooling leg.
(2) Automatic Flow Regulator (tankless only) must match GPM
rating of the tankless. If piped downstream of mixing valve,
GPM flow will increase if heater water is hotter than 120°F.
(3) Placement of hose bibs will permit periodic back flushing of
heater (coil).

27
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

3. INDIRECT DOMESTIC HOT WATER CONCERN

Scalding: Temperature - Minimum Time - Degree of Burn
Temp (°F) 1st Degree 2nd & 3rd Degree
111.2° 5 hrs. 7 hrs.
116.6° 35 min. 45 min.
118.4° 10 min. 14 min.
122.0° 1 min. 5 min.
131.0° 5 sec. 22 sec.
140.0° 2 sec. 5 sec.
149.0° 1 sec. 2 sec.
158.0° 1 sec. 1 sec.
INDIRECT SWIMMING POOL HEATING
APPLICATION
The use of a house heating boiler to indirectly heat a swimming pool is
possible and even desirable. A factor of major significance would be
comparable heat loads.
SIZING CONSIDERATIONS
Gallons of water to heat, temperature rise, and time allotted for
temperature rise.
1. SIZING FORMULA (INITIAL RAISING OF WATER
TEMPERATURE)
Gallons of Water = Pool (width x length x avg. depth) x 7.48
(gal. per cu. ft.)
Gallons of water x 8.34 x temp. rise ÷ hours to heat pool = BTUH
Example: Pool (40' x 20' x 5' avg.)
with initial pool water of 55°F to be raised to 75°F
allowing 48 hours to raise temperature
40' x 20' x 5' x 7.48 = 29,920 gallons of water
29,920 x 8.34 x 20 ÷ 48 = 103,972 BTUH (I=B=R Net Ratings).
2. HEAT LOSS FROM POOL SURFACE*
(MAINTAINING WATER TEMPERATURE)
Temperature
Difference °F 10° 15° 20° 25° 30°
BTUH/per Sq. Ft. 105 158 210 263 368
Notes: •Assumed wind velocity: 3.5 mph
Wind velocity of 5 mph multiply BTUH by 1.25
Wind velocity of 10 mph multiply BTUH by 2.00
•Temperature Difference: Ambient air and desired water temp.
* Maintaining pool temperature when outside air is 20° to 30°F lower
than pool water may require a larger boiler.
28
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

PIPING: INDIRECT SWIMMING POOL HEATING

Note: By-pass enables one to regulate flow through heat exchanger and
also provide a manual disconnect from heating system.

29
CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

PIPING: HOT WATER SYSTEM AIR CUSHION

AND AIR REMOVAL OPTIONS

AIR REMOVAL SYSTEM

AIR CONTROL SYSTEM

30
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

1. BOILER BY-PASS - ONE ZONE

31
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

1. BOILER BY-PASS - ONE ZONE (CONT.)

PURPOSE FOR BY-PASS

GAS BOILER CONNECTED TO LARGE WATER CONTENT
RADIATION
• Flue gas condensation will occur when the "burner" is on and the water
in the boiler is less than 130°F. Over 50% of the heating season the
radiators will satisfy the need for heat with less than 130°F. By-pass
piping will permit the boiler to carry a higher temperature than the
radiation. Regulation comes from the globe or plug valves. Ther-
mometers, positioned above, will facilitate a proper by-pass. The
supply water temperature need only overcome the temperature drop
of the system. Even with water moving as slow as 2' to 1' per second
in the oversized gravity piping, within a few minutes the thermom-
eter mounted in the by-pass (return water) will begin to register
temperature rise then serious balancing can start.

OIL BOILER WITH TANKLESS CONNECTED TO LARGE WATER

CONTENT RADIATION
• Flue gas condensation can occur in oil boilers too. However, there is
greater concern regarding system operation. Without a boiler by-
pass, water returning from one radiator will drastically drop the boiler
temperature and cause the circulator to stop. Heat leaves the boiler
in "spurts" and all the "hot 'spurts'" end up in the same radiator and
the heating system is quickly out of balance. By-pass piping properly
set will dramatically minimize this problem.

32
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

2. BOILER BY-PASS - MULTI-ZONE HEATING

PURPOSE OF BY-PASS (GAS AND OIL)

• In a multi-zone (cold start) system excess temperature develops.

When one zone calls for heat it cannot dissipate the heat the boiler
(sized for all zones) creates. When the zone is satisfied the hot water
trapped in the boiler stays hot while the hot water trapped in the non-
ferrous baseboard cools quickly. Before the next call for heat the
temperature difference may be as high as 100°F. The system will be
plagued with expansion noises unless boiler by-pass piping is installed.
If, for example, the temperature drop in each of the zones is
approximately 10°F then the balancing valves need only show on the
thermometers a 15°F variance between supply and return piping, and
expansion noises will be eliminated.
Beyond Boiler By-Pass
• Two-stage thermostats or an indoor-outdoor reset controller will
minimize the temperature rise in the boiler but even with these
controls, boiler by-pass piping will help.

33
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

3. BOILER BY-PASS - MULTI-ZONE HEATING AND INDI-

RECT D.H.W. ZONE

34
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

3. BOILER BY-PASS - MULTI-ZONE HEATING AND

INDIRECT D.H.W. ZONE (CONT.)

PURPOSE OF BY-PASS (GAS AND OIL)

• Serves only the heating zones. Though, indirectly, the

hotter boiler water it creates will help the indirect domestic hot
water zone. Boiler by-pass piping, per se, is helpful to the heating
zones yet detrimental to the DHW zone. However, with properly
positioned check valve by-pass piping can serve both
operations.

EXAMPLES
1. Heating zone (2, 3 or 4) calls for heat: Full flow of the
circulator will move from the radiation to point (A). If the
balancing valves (globe or plug) are adjusted to slightly
overcome the temperature drop of the zone(s), typically
30% of the flow will move into the boiler at point (B) and
70% will by-pass the boiler at (C). At point (D) the full, but
blended, flow will move to the radiation.

2. Indirect DHW zone (1) calls for heat: Full flow of the
circulator will move through the boiler at (B). No water will
move through the by-pass at (C) because of the check valve
at point (E). In other words, all the heat in the boiler will be
dedicated to satisfying the DHW needs.

3. Heating zone and indirect DHW zone call for heat simulta-
neously. Through the use of a special relay the DHW zone
could be given priority. This means the heating zone is put
on hold until the DHW zone is satisfied. One option would
be to let the piping handle the situation. Remember, water
flow takes the course of least restriction and there is
considerably less restriction in the DHW zone piping.

35
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

4. BOILER BY-PASS VS SYSTEM BY-PASS

Several variations of by-pass piping exist for different reasons.

Because the piping is near the boiler it is commonly categorized as
“boiler by-pass” even though some may be a “system by-pass”. The
difference is illustrated below.

1. Drawing illustrates how 1. Drawing illustrates how

water by-passes the boiler. water by-passes the system.

2. Total circulator’s capacity is 2. Some of the circulator’s

dedicated to the system capacity is used to
recirculate boiler water.

36
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

5. BOILER BY-PASS - THREE-WAY MIXING VALVES

NOTES:

· Restricting boiler water flow will increase return water flow and vice
versa. Supply water flow will always be boiler water plus return
water.

· Mixing may be accomplished manually or with an actuating motor.

· Three-way valve application is a boiler by-pass.

37
 CHAPTER 2 - HOT WATER PIPING - RESIDENTIAL

6. SYSTEM BY-PASS - FOUR-WAY MIXING VALVE

1. With application of four-way valve the preferred location

of the circulator is on the "system supply" side.
2. Mixing may be accomplished manually or with an
actuating motor.
3. Four-way valve application is a system by-pass.
4. Four-way valve application may require a second
circulator, one dedicated to system flow and the other to
boiler flow. The second circulator should be installed at
point (A) pumping into the boiler
5. Concern: Should four-way valve be fully opened to the
system, both circulators will be pumping in series.

38
 CHAPTER 3 - DOMESTIC HOT WATER

DOMESTIC HOT WATER SIZING REQUIREMENTS

A. RESIDENTIAL: Sizing residential water heaters vary with manufacturers.

HUD and FHA have established minimum permissible water heater sizes as
shown in the following table.

HUD--FHA Minimum Water Heater Capacities for

One- and Two-Family Living Units
Number of Baths 1 to 1.5 2 to 2.5 3 to 3.5

Number of Bedrooms 1 2 3 2 3 4 5 3 4 5 6

GAS (a)
Storage, gal 20 30 30 30 40 40 50 40 50 50 50
1000 Btu/h input 27 36 36 36 36 38 47 38 38 47 50
1-h draw, gal 43 60 60 60 70 72 90 72 82 90 92
Recovery, gph 23 30 30 30 30 32 40 32 32 40 42

TANK TYPE INDIRECT (b,c)

I-W-H rated draw, gal in

3-h, 100°F rise 40 40 66 66 66 66 66 66 66

Manufacturer-rated draw, gal in

3-h, 100°F (55.6°C) rise 49 49 75 75d 75 75 75 75 75

Tank capacity, gal 66 66 66 66d 82 66 82 82 82

TANKLESS TYPE INDIRECT (c,e)

I-W-H rated, gpm

100°F rise 2.75 2.75 3.25 3.25d 3.75 3.25 3.75 3.75 3.75

a. Storage capacity, input, and recovery requirements indicated in the table are typical and
may vary with each individual manufacturer. Any combination of these requirements to
produce the stated 1-h draw will be satisfactory.
b. Boiler-connected water heater capacities [180°F boiler water, internal or external
connection].
c. Heater capacities and inputs are minimum allowable. A.G.A. recovery ratings for gas
heaters, and IBR ratings for steam and hot water heaters.
d. Also for 1 to 1.5 baths and 4 B.R. for indirect water heaters.
e. Boiler-connected heater capacities [200°F boiler water, internal or external connection].

Reference: ASHRAE/Systems Handbook (Service Water Heating)

39
 CHAPTER 3 - DOMESTIC HOT WATER

B. COMMERCIAL: Commercial buildings have different domestic hot water needs.

Building Type will be the major variable. The two charts that follow analyze the
demand based either on Fixture or on Occupancy.
Note: Both charts presume the use of storage type heaters.
Chart #1
[Gallons of water per hour per fixture, calculated at a final temperature of 140°F]
Apt. Ind. Ofice Priv.
House Club Gym Hospital Hotel Plant Bldg. Res. School YMC

1. Basins, private lavatory 2 2 2 2 2 2 2 2 2 2

2. Basins, public lavatory 4 6 8 6 8 12 6 -- 15 8
3. Bathtubs 20 20 30 20 20 -- -- 20 -- 30
4. Dishwashers 15 50-10 -- 50-150 50-20 20-10 -- 15 20-100 20-100
5. Foot basins 3 3 12 3 3 12 -- 3 3 12
6. Kitchen Sink 10 20 -- 20 30 20 20 20 20 20
7. Laundry, stationary tubs 20 28 -- 28 28 -- -- 20 -- 28
8. Pantry sink 5 10 -- 10 10 -- 10 5 10 10
9. Showers 30 150 225 75 75 225 30 30 225 225
10. Slop sink 20 20 -- 20 30 20 20 15 20 20
11. Hydrotherapeutic
showers 400
12. Circular wash sinks 20 20 30 20 30
13. Semicircular wash sinks 10 10 15 10 15
14. DEMAND FACTOR 0.30 0.30 0.40 0.25 0.25 0.40 0.30 0.30 0.40 0.40
15. STORAGE CAPACITY
FACTOR 1.25 0.90 1.00 0.60 0.80 1.00 2.00 0.70 1.00 1.00
Notes:
A. #1 through #13 - Possible Maximum Demand.
B. #14 (Demand Factor) - Probable Maximum Demand
C. #15 Ratio of Storage Tank Capacity to Probable Max. Demand Per Hr.

Example:
50 Unit Apartment Building
50 lavatories x 2 = 100 GPH
50 showers x 30 = 1500 GPH
50 kitchen sinks x 10 = 500 GPH
10 laundry tubs x 20 = 200 GPH
A) Possible Maximum Demand = 2300 GPH
Demand Factor (#14) x .30
B) Probable Maximum Demand = 690 GPH
Storage Capacity Factor (#15) 1.25
C) Storage Tank Size = 863 GAL.

40
 CHAPTER 3 - DOMESTIC HOT WATER

CHART #2
This chart may be used as a cross check to Chart #1. The Hot Water Demand listed
represents the actual metering of 129 buildings. The number of each building type
sampled is listed at the extreme left side of chart.
Maximum Maximum
Number Type of Building Hour Day Average Day
3.8 22.0 13.1
8 Men’s dormitories
gal/student gal/student gal/student
5.0 26.5 12.3
8 Women’s dormitories
gal/student gal/student gal/student
Motels: no. of units (a)
20 or less, 6.0 gal/unit 35.0 gal/unit 20.0 gal/unit
15
60 5.0 gal/unit 25.0 gal/unit 14.0 gal/unit
100 or more 4.0 gal/unit 15.0 gal/unit 10.0 gal/unit
13 Nursing homes 4.5 gal/bed 30.0 gal/bed 18.4 gal/bed
6 Office buildings 0.4 gal/person 2.0 gal/person 1.0 gal/person
Food establishments:
Type A--full meal
restaurants and cafeterias 1.5 gal/max 11.0 gal/max 2.4 gal/avg
25
Type B--drive-ins, grilles, meals/h meals/h meals/day*
luncheonettes, sandwich 0.7 gal/max 6.0 gal/max 0.7 gal/avg
and snack shops meals/h meals/h meals/day*
Apartment houses: no. of
apartments
20 or less 12.0 gal/apt. 80.0 gal/apt. 42.0 gal/apt.
26 50 10.0 gal/apt. 73.0 gal/apt. 40.0 gal/apt.
75 8.5 gal/apt. 66.0 gal/apt. 38.0 gal/apt.
100 7.0 gal/apt. 60.0 gal/apt. 37.0 gal/apt.
200 or more 5.0 gal/apt. 50.0 gal/apt 35.0 gal/apt.
0.6 1.5 0.6
14
Elementary schools gal/student gal/student gal/student*
1.0 3.6 1.8
14
Junior and senior high schools gal/student gal/student gal/student*
*Per day of operation.
(a) Interpolate for intermediate values.

Reference: ASHRAE/Systems Handbook (Service Water Heating)

41
 CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

SIZING OBSOLETE RADIATION - CAST IRON RADIATORS

The output of a radiator is measured in square feet of radiation.
To determine the number of square feet of radiation in a radiator:
1. Measure the height of the radiator.
2. Count the number of columns in a section.
3. Count the number of sections.
4. Multiply the total number of sections by the number of
square feet per section as shown in the following tables:
Column Type Radiators

Sq. Ft. Radiation Per Section

4-1/2" W 7-1/2" W 9" W 11-1/2" W 13"W
Height One Two Three Four
Inches Column Column Column Column Window
13 — — — — 3
16 — — — — 3-3/4
18 — — 2-1/4 3 4-1/4
20 1-1/2 2 — — 5
22 — — 3 4 —
23 1-2/3 2-1/3 — — —
26 2 2-2/3 3-3/4 5 —
32 2-1/2 3-1/3 4-1/2 6-1/2 —
38 3 4 5 8 —
45 — 5 6 10 —
42
 CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

Tube Type Radiators

Sq. Ft. Radiation Per Section

5" 7" 8-3/4" 9-3/4" 12-1/2"
Height Three Four Five Window Seven
Inches Tube Tube Tube Six Tube Tube
14 — — — — 2-1/2
17 — — — — 3
20 1-3/4 2-1/4 2-2/3 3 3-2/3
23 2 2-1/2 3 3-1/2 —
26 2-1/3 2-3/4 3-1/2 4 4-3/4
32 3 3-1/2 4-1/3 5 —
38 3-1/2 4-1/4 5 6 —

Wall Type Radiators

Wall radiators are measured by their height, length and thickness. The
following table shows the number of square feet of heating surface per
section.

Sq. Ft. Radiation Per Wall Radiator Section Heating

Type of Height Length or Thickness Sq. Ft.
Section In. Width In. In. Radiation
5-A 13-5/16 16-5/8 2-7/8 5
7-A 13-5/16 21-7/8 2-7/8 7
7-B 21-7/8 13-3/16 3-1/16 7
9-A 18-5/16 29-1/16 2-7/8 9
9-B 29-1/16 18-5/16 3-11/16 9
43
 CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

CONVECTORS
Cast Iron - Ratings: Page 43

Copper - Ratings: Page 44

44
CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

SIZING: CONVECTORS - CAST IRON

RATINGS - SQUARE FEET OF RADIATION

FRONT OUTLET
AND SLOPING
OUTLET TYPE
UNITS
Cabinet Height - 18 20 24 26 32 38
Floor Types
Cabinet Cabinet
Depth Length
Inches Inches
18½ 8.4 9.1 10.5 11.0 11.8 12.3
23½ 10.9 11.8 13.5 14.2 15.2 15.9
28½ 13.3 14.4 16.5 17.4 18.6 19.4
33½ 15.8 17.1 19.7 20.6 22.1 23.0
38½ 18.2 19.7 22.7 23.8 25.5 26.5
4½" 43½ 20.6 22.3 25.7 26.9 28.9 30.1
48½ 23.1 25.0 28.7 30.1 32.3 33.6
53½ 25.5 27.6 31.8 33.3 35.7 37.2
58½ 28.0 30.3 34.8 36.5 39.1 40.7
63½ 30.5 33.0 37.9 39.7 42.5 44.3
18½ 12.3 13.5 15.4 16.2 17.5 18.2
23½ 15.9 17.4 19.9 20.9 22.6 23.5
28½ 19.5 21.3 24.4 25.6 27.7 28.8
33½ 23.1 25.2 28.9 30.4 32.9 34.1
38½ 26.7 29.2 33.4 35.1 38.0 39.4
6½" 43½ 30.3 33.1 37.9 39.8 43.1 44.7
48½ 33.9 37.0 42.4 44.5 48.1 50.0
53½ 37.5 40.9 46.8 49.2 53.3 55.3
58½ 41.1 44.8 51.3 53.9 58.4 60.6
63½ 44.7 48.7 55.8 58.7 63.5 65.9
18½ ----- 17.1 19.4 20.4 22.5 23.7
23½ ----- 22.2 25.0 26.4 29.1 30.6
28½ ----- 27.2 30.7 32.4 35.7 37.5
33½ ----- 32.2 36.4 38.4 42.3 44.5
38½ ----- 37.2 42.1 44.3 48.9 51.4
8½" 43½ ----- 42.3 47.8 50.3 55.5 58.4
48½ ----- 47.3 53.5 56.3 62.0 65.3
53½ ----- 52.3 59.2 62.3 68.6 72.3
58½ ----- 57.3 64.9 68.3 75.2 79.2
63½ ----- 62.3 70.6 74.3 81.8 86.1
18½ ----- 20.6 23.4 24.6 27.3 28.8
23½ ----- 26.7 30.3 31.8 35.3 37.2
28½ ----- 32.8 37.2 39.1 43.3 45.7
33½ ----- 38.9 44.2 46.3 51.4 54.2
38½ ----- 45.0 51.1 53.6 59.5 62.7
10½" 43½ ----- 51.1 58.0 60.8 67.5 71.2
48½ ----- 57.2 64.9 68.1 75.6 79.6
53½ ----- 63.3 71.8 75.4 83.6 88.1
58½ ----- 69.4 78.7 82.6 91.6 96.6
63½ ----- 75.5 85.6 89.8 99.7 105.1

45
 CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

SIZING: CONVECTORS - COPPER

FRONT OUTLET TYPE UNITS
RATINGS - SQUARE FEET OF RADIATION
FRONT OUTLET
AND SLOPING
OUTLET TYPE
UNITS
Cabinet Height - 18 20 24 26 32 38
Floor Types
Cabinet Cabinet
Depth Length
Inches Inches
20½ 10.4 11.3 13.1 13.4 14.0 14.6
24½ 12.8 13.9 16.1 16.4 17.2 18.0
28½ 15.2 16.5 19.2 19.5 20.4 21.3
32½ 17.6 19.1 22.2 22.5 23.6 24.6
36½ 19.7 21.7 25.2 25.6 26.8 28.0
4-1/4" 40½ 22.3 24.3 28.2 28.6 30.0 31.3
44½ 24.7 26.9 31.2 31.7 33.2 34.7
48½ 27.1 29.5 34.2 34.7 36.4 38.0
56½ 31.9 34.7 40.2 40.8 42.8 44.7
64½ 36.6 39.9 46.2 46.9 49.2 51.7
20½ 15.3 16.3 18.4 18.8 19.6 20.6
24½ 18.8 20.1 22.6 23.1 24.1 25.3
28½ 22.3 23.8 26.9 27.4 28.6 30.1
32½ 25.8 27.6 31.1 31.7 33.2 34.8
6-1/4" 36½ 29.3 31.3 35.4 36.0 37.7 39.6
40½ 32.8 35.1 39.6 40.3 42.2 44.3
44½ 36.3 38.9 43.8 44.6 46.7 49.0
48½ 39.8 42.6 48.1 48.9 51.2 53.8
56½ 46.8 50.1 56.6 57.5 60.3 63.3
64½ 53.9 57.7 65.0 66.2 69.3 72.7
20½ 18.7 20.0 22.5 23.0 24.4 25.8
24½ 22.9 24.5 27.7 28.2 30.0 31.7
28½ 27.2 29.1 32.8 33.5 35.6 37.7
32½ 31.5 33.7 38.0 38.8 41.2 43.6
36½ 35.8 38.3 43.2 44.1 46.8 49.5
8-1/4" 40½ 40.1 42.9 48.3 49.4 52.4 55.5
44½ 44.3 47.4 53.5 54.6 58.0 61.4
48½ 48.6 52.0 58.7 59.9 63.6 67.3
56½ 57.2 61.2 69.0 70.5 74.8 79.2
64½ 65.7 70.3 79.4 81.0 86.0 91.0
20½ 20.4 22.0 25.0 25.7 27.4 29.3
24½ 25.2 27.1 30.9 31.7 33.8 36.2
28½ 30.0 32.3 36.8 37.7 40.2 43.1
32½ 34.8 37.4 42.6 43.7 46.6 50.0
36½ 39.6 42.6 48.5 49.8 53.1 56.9
10-1/4" 40½ 44.4 47.7 54.4 55.8 59.5 63.7
44½ 49.2 52.9 60.3 61.8 65.9 70.6
48½ 53.9 58.0 66.1 67.8 72.3 77.5
56½ 63.5 68.3 77.9 79.9 85.2 91.2
64½ 73 1 78 6 89 6 91 9 98 0 105 0

46
 CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

STEEL PIPE COILS - Sq Ft of Radiating Surface Per Linear Ft of Coil

Nominal Number of Rows of Pipe In Coil

Pipe
Size
(Inches) 1 2 3 4 5 6 8 10
1 .57 1.09 1.53 1.90 2.20 2.44 2.83 3.14
1-1/4 .71 1.36 1.91 2.37 2.74 3.04 3.52 3.90
1-1/2 .81 1.55 2.18 2.70 3.12 3.46 4.02 4.45
2 .95 1.81 2.55 3.17 3.66 4.05 4.71 5.22
Notes: 1. Based on 70°F room temperature.
2. Pipes are positioned level, on vertical wall.
3. For coils positioned along floor or ceiling.
Multiply chart value for 1 row of pipe x no. of rows of pipe.

CORRECTION FACTORS IF ROOM TEMPERATURE IS OTHER

THAN 70° DIVIDE SQ. FT. OF RADIATION BY
Rm. Temp 80° 75° 70° 65° 60° 55° 50°
Divisor 1.10 1.05 1.00 0.96 0.92 0.88 0.85

Heat Emissions for Cast Iron Radiators

Design or Heat Emissions Design or Heat Emission
Average Water Rates Average Water Rates
Temperature Btuh per sq. ft. Temperature Btuh per sq. ft.
110° 30 180° 170
120° 50 185° 180
130° 70 190° 190
140° 90 195° 200
150° 110 200° 210
160° 130 205° 220
170° 150 210° 230
175° 160 215° 240
47
 CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

HEAT LOSSES FROM BARE STEEL PIPE

Based On 70° Surrounding Air
Temperature of Pipe, Deg. F
Diameter
of Pipe, 100 120 150 180 210 240
Inches Heat Loss per Lineal Foot of Pipe, BTU per Hour
1/2 13 22 40 60 82 106
3/4 15 27 50 74 100 131
1 19 34 61 90 123 160
1-1/4 23 42 75 111 152 198
1-1/2 27 48 85 126 173 224
2 33 59 104 154 212 275
2-1/2 39 70 123 184 252 327
3 46 84 148 221 303 393
3-1/2 52 95 168 250 342 444
4 59 106 187 278 381 496
5 71 129 227 339 464 603
6 84 151 267 398 546 709
8 107 194 341 509 697 906
10 132 238 420 626 857 1114
12 154 279 491 732 1003 1305
14 181 326 575 856 1173 1527
16 203 366 644 960 1314 1711
18 214 385 678 1011 1385 1802
20 236 426 748 1115 1529 1990

HEAT LOSSES FROM BARE TARNISHED COPPER TUBE

Based On 70° Surrounding Air
Temperature of Pipe, Deg. F
Diameter
of Pipe, 100 120 150 180 210 240
Inches Heat Loss per Lineal Foot of Pipe, BTU per Hour
1/4 4 8 14 21 29 37
3/8 6 10 18 28 37 48
1/2 7 13 22 33 45 59
5/8 8 15 26 39 53 68
3/4 9 17 30 45 61 79
1 11 21 37 55 75 97
1-1/4 14 25 45 66 90 117
1-1/2 16 29 52 77 105 135
2 20 37 66 97 132 171
2-1/2 24 44 78 117 160 206
3 28 51 92 136 186 240
3-1/2 32 59 104 156 212 274
4 36 66 118 174 238 307
5 43 80 142 212 288 373
6 51 93 166 246 336 432
8 66 120 215 317 435 562
10 80 146 260 387 527 681
12 94 172 304 447 621 802

48
CH. 4 - INSTALLED RADIATION: DETERMINING HEAT LOAD

HEAT LOSSES FROM COVERED PIPE

85 PERCENT MAGNESIA TYPE
BTU PER LINEAR FOOT PER HOUR PER °F TEMPERATURE
DIFFERENCE (SURROUNDING AIR ASSUMED 75 °F)
Insulation, Max. Temp. of Pipe Surface °F.
Pipe Thickness,
Size Inches 125 175 225 275
½ 1 .145 .150 .157 .160
¾ 1 .165 .172 .177 .180
1 .190 .195 .200 .203
1
1½ .160 .165 .167 .170
1 .220 .225 .232 .237
1¼
1½ .182 .187 .193 .197
1 .240 .247 .255 .260
1½
1½ .200 .205 .210 .215
1 .282 .290 .297 .303
2 1½ .230 .235 .240 .243
2 .197 .200 .205 .210
1 .322 .330 .340 .345
2½ 1½ .260 .265 .270 .275
2 .220 .225 .230 .237
1 .375 .385 .395 .405
3 1½ .300 .305 .312 .320
2 .253 .257 .263 .270
1 .419 .430 .440 .450
3½ 1½ .332 .339 .345 .352
2 .280 .285 .290 .295
1 .460 .470 .480 .492
4 1½ .362 .370 .379 .385
2 .303 .308 .315 .320
1 .545 .560 .572 .585
5 1½ .423 .435 .442 .450
2 .355 .360 .367 .375
1 .630 .645 .662 .680
6 1½ .487 .500 .510 .520
2 .405 .415 .420 .430

49
 CHAPTER 5 - WATER CONTENT
EXISTING RADIATION/PIPING

A. RADIATION
Based on Sq. Ft. Rating Water Content/Gal. Weight/Lbs.
Slenderized Radiators 0.066 4.5
Large Tube Radiators 0.103 5.25
Column Radiators 0.188 7.0
Convectors (Non-Ferrous) 0.004 1.5
Convectors (Cast Iron) 0.040 3.4
Radiant Radiators 0.066 5.0
Base-Ray (Cast Iron Baseboard) 0.066 4.4

B. STEEL AND WROUGHT IRON PIPE (STD. WGT.)

Nominal Size: Based On Lineal Foot
Inches Water Content/Gal. Weight/Lbs.
1/2" .016 .132
3/4" .028 .231
1" .045 .375
1-1/4" .078 .648
1-1/2" .106 .883
2" .174 1.455
2-1/2" .249 2.076
3" .384 3.205
4" .661 5.519
5" 1.039 8.662
6" 1.501 12.510

C. COPPER TUBING (TYPE L)

Nominal Size: Based on Lineal Foot
Inches Water Content/Gal. Weight/Lbs.
3/8" .007 .063
1/2" .012 .101
5/8" .018 .151
3/4" .025 .210
1" .043 .357
1-1/4" .065 .544
1-1/2" .092 .770
2" .161 1.340

D. WATER CONVERSION FACTORS

Lbs. of Water x 0.12 = Gallons
Gallons of Water x 8.34 = Lbs.

50
 CHAPTER 6 - HEAT LOSS CALCULATION

SHORT FORM HEAT LOSS SURVEY

Application: Excellent when determining heat loss of a building as a
whole.Precise method of sizing replacement hot water boilers.
*Heating Multipliers (H.M.) BTU/Hr. Based on 60°F Temperature
Difference (T.D.)
WALL *H.M. CEILING *H.M. FLOOR *H.M.
No Insulation 1 5 3 Inches 5 No Insulation 4
2 Inches 6 6 Inches 4 Overhang — 3" 5
3 Inches 4 10 Inches 2 Overhang — 6" 3
WINDOWS/DOOR *H.M. INFILTRATION *H.M.
Storm 34 1-1/2 Air Change 1.61
Insulated 41 1 Air Change 1.07
Single 67 3/4 Air Change .81
PROCEDURE:
1. Measure the length (L) and width (W) of the outside walls of the
house and record. Calculate gross wall area by multiplying height of the
walls by total length of outside walls. (2L + 2W).
2. Measure the window and door area and record.
3. Record Net Wall Area = (gross wall area minus door and window
area) select proper H.M.
4. Measure and record the ceiling area and select H.M.
5. Measure and record floor area and select H.M. (H.M. of 4 used
unheated basement).
6. Multiply Floor area by ceiling height to obtain volume of home and
select proper air change factor: 1.61 for Loose House - 1.07 for
Average House - .81 for Tight House.
H.M. Floor over Basement T.D. 20°
WORKSHEET:
LENGTH _________ WIDTH __________ HEIGHT _______
AREA (ft 2) H.M. (BTU/Hr.) BTU/Hr. LOSS

GROSS ____________________________ X _________ = _____________

WINDOWS & DOORS ______________ X _________ = _____________
NET WALL _______________________ X _________ = _____________
CEILING __________________________ X _________ = _____________
FLOOR ___________________________ X _________ = _____________
INFILTRATION (CU. FT.) __________ X _________ = _____________
(HEIGHT) X (FLOOR AREA)

TOTAL HEAT LOSS = __________

TEMP. DIFFERENCE CORRECTION = __________
*To Increase Temp. Difference to70°F, Multiply Total Heat Loss 1.18
80°F, Multiply Total Heat Loss 1.34
90°F, Multiply Total Heat Loss 1.50
100°F, Multiply Total Heat Loss 1.66
51
 CHAPTER 6 - HEAT LOSS CALCULATION

GREENHOUSE HEAT LOSS CALCULATION

The method described in this manual based on the method prepared and
adopted by N.G.M.A. (National Greenhouse Manufacturer's Associa-
tion).
The recommended equation for calculating heat loss is:
[A1 + (A2 x R)] x TD x G x W x C = BTU/Hr. Heat Loss, where:
A1 - Square feet of exposed glass area;
A2 - Square feet to exposed wall area (other than glass);
R - Resistance of greenhouse wall base transposed into a
"glass" factor;
T - Highest temperature to be maintained is greenhouse minus
outside design temperature;
G - Coefficient of transmission of glass is BTU/Hr./Ft.2/°F.
(Table 2).
W - Wind factor (Table 3);
C - Construction factor (Table 4).
Example (See Figure 1):
Given: Glass area = 4040 ft.2 Find: "R" for 8" brick wall = 0.43;
wall area = 810 ft.2 TD x "G" (Table 5) = 79;
design temperature: "W" for 15 mph wind = 1.00;
inside = 60°F "C" for all metal, glass = 1.08
outside = .10°F
brick wall = 8" thick
wind = 15 mph or less
Calculate:
Heat Loss = [A1 + (A2 x R)] x TD x G x W x C
= [404 + (810 X 0.43)] x 79 x 1.00 x 1.08]
= 4388 x 85.3
= 374,000 BTU/Hr.

Figure 1
Typical Greenhouse
52
 CHAPTER 6 - HEAT LOSS CALCULATION

TABLE 1 - "R" FACTOR

These are factors for "curtain" wall materials normally used on green-
houses:
3/8 in. Courrugated asbestos cement board wall 0.94
4 in. Poured concrete wall 0.76
6 in. Poured concrete wall 0.67
8 in. Poured concrete wall 0.60
4 in. Concrete block wall 0.58
8 in. Concrete block wall 0.46
8 in. Brick Wall 0.43
TABLE 2 TABLE 3
COEFFICIENT OF WIND "W" FACTOR (2)
TRANSMISSION OF GLASS If wind velocity exceeds 15
("G" FACTOR) mi. per hr. average during
Temp. Diff. the heating season, the
Between Inside Coefficient heat loss calculation should
& Outside of be increased by 4% for each
DesignTemp. Transmission 5 mi. per hr. over 15 as
50° 1.09 below:
55° 1.10 Wind
60° 1.11 Velocity
65° 1.12 In Alternate
70° 1.13 Miles Per "W" "W"
75° 1.14 Hour Factor Factor (3)
80° 1.15 15 m.p.h. 1.00 1.10
85° 1.16 or less
90° 1.17 20 m.p.h. 1.04 1.14
95° 1.18
25 m.p.h. 1.08 1.18
100° 1.19
30 m.p.h. 1.12 1.22
105° 1.20
35 m.p.h. 1.16 1.26

TABLE 4 - CONSTRUCTION "C" FACTOR (4)

The condition and type of a greenhouse directly affect the heat
loss. Consult this table for the factor which best describes the
greenhouse on which you are calculating the heat loss.
All metal (good tight glass house - 20 or 24 in. glass spacing) 1.08
Wood & steel (good tight glass house - 16 or 20 in. glass spacing)
(Metal gutters, vents, headers, etc.) 1.05
Wood houses (glass houses with wood bars, gutters, vents, etc.-
up to and including 20 in. glass spacing)
Good tight houses 1.00
Fairly tight houses 1.13
Loose houses 1.25
Fiberglass covered wood houses 0.95
Fiberglass covered metal houses 1.00
Plastic covered (5) metal houses (single thickness) 1.00
Plastic covered (6) metal houses (double thickness) 0.70
53
 CHAPTER 6 - HEAT LOSS CALCULATION

GREENHOUSE HEAT LOSS CALCULATION

TABLE 5 - HEAT REQUIREMENTS FOR GREENHOUSES
BTU/Hr. for each equivalent square foot of glass [C = 1.00 (7); W = 1.00
(8)]
Inside Outside design Temperature - °F
Temp
°F -30 -20 -10 0 10 20 30
40 79 67 54 43 33 22 11
45 86 73 61 49 38 27 16
50 92 79 67 54 43 33 22
55 99 86 73 61 49 38 27
60 105 92 79 67 54 43 33
65 112 99 86 73 61 49 38
70 119 105 92 79 67 54 43
75 126 112 99 86 73 61 49

TABLE 6 - CUSTOMARY NOTES

GREENHOUSE TEMPERA- 2. The effect of wind on heat loss
TURES cannot be overemphasized. If
Type of Plant or Temperature increased wind velocity is not
compensated for, there is likely
Building Use Range, °F to be a ½° temperature drop for
Carnation 45-55 every mile per hour over 15
Chrysanthemums, mph. These figures are based
cut flowers on observations by greenhouse
and potted plants 60-65 heating design engineers over
Cool 45-50 many years of observation.
Cucumber 65-60 3. Lapped glass on greenhouses
normally freezes shut when the
Fern 60-65 outdoor temperature reaches
Forcing 60-65 15° above zero. If high design
General purpose 55-60 temperatures are used (70° or
Lettuce 40-45 over), if unit heaters or
turbulators are located so that
Orchid, warm 65-70 they blow air against the glass,
Orchid, cool 50-55 if 40% or more of the
Palm, warm 60-65 greenhouse radiation will be
Palm, cool 50-55 overhead, or if the "green-
house" will be used for other
Poinsettias 60-70 than "growing" purposes, use
Propagating 55-60 alternate "W" factors above.
Rose 55-60 4. These figures are based on
Sweet pea 45-50 observations by greenhouse
Tomato 65-70 heating design engineers.
Tropical 65-70 5. With no air leaks (holes, tears,
etc.)
Violet 40-45
6. ¼" minimum, 1½" maximum
distance between layers with no
air leaks (holes, tears, etc.)
54
 CH. 7 - FUEL CONSUMPTION AND ENERGY COST

There are several ways to calculate the operational cost of a

specific boiler in a particular location. The accuracy of each will depend
on the attention one gives the many variables.
Two popular methods are the “bin” and “degree-day”. Though
the “bin” method has the potential to be more accurate, it is more
complicated when necessary weather data is not readily available.
Discussion will be limited to the “Degree-Day” method.
The “Degree-Day” method is not without controversy. Histori-
cally, the reference temperature is 65°. This assumes that a building with
average insulation and a thermostat set at 70° will cause a boiler to begin
operation when outdoor temperature falls below 65°. Overlooked
variables could be sunshine, wind, heavier insulation, different thermo-
stat setting.
WHAT IS A DEGREE DAY?
When the outside temperature falls below 65°F, heat will be
required to maintain the temperature within the building. The average
outside temperature is estimated by adding the high and low temperature
for a given day and dividing by two. (Example: A high of 40°F and a low
of 20°F would be equivalent to a 30°F average temperature.) “Degree
Days” are defined as the difference between the average temperature and
the 65°F reference temperature. Therefore, 65°F minus 30°F equals 35
“Degree Days”.
Degree Days = 65 - (high + low) ÷2
FUEL CONSUMPTION
In order to determine fuel usage the D.D. is used in the
following equation:
HL x 24 x DD
F=
E x P x T.D.
HL = Heating Load (Btuh)
DD = Degree Day
24 = Hours in a day
E = *Boiler Efficiency (AFUE)
P = Heating value of fuel (Btu)
T.D. = Design temperature difference
(inside-outside)
F = Annual fuel consumption
*Example: 80% = .8

55
 CH. 7 - FUEL CONSUMPTION AND ENERGY COST

HEATING DEGREE DAYS (SAMPLING) USA/CANADA

STATE/PROVINCE/CITY D.D. STATE/PROVINCE/CITY D.D.

Alaska Indianapolis 5630
Anchorage 10860 South Bend 6460
Barrow 20265
Fairbanks 14290 Iowa
Des Moines 6610
Colorado Dubuque 7380
Alamosa 8529
Colorado Springs 6410 Kansas
Denver 6150 Topeka 5210
Wichita 4640
Connecticut
Bridgeport 5617 Kentucky
Hartford 6170 Lexington 4760
Waterbury 6672 Louisville 4610

Delaware Maine
Wilmington 4930 Bangor 8220
Portland 7570
District of Columbia
Washington 4240 Maryland
Baltimore 4680
Georgia Hagerstown 5130
Atlanta 2990
Massachusetts
Idaho Boston 5630
Boise 5830 Lowell 6060
Pocatello 7030 Pittsfield 7580
Worcester 6970
Illinois
Champaign/Urbana 5800 Michigan
Chicago, O’Hare 6640 Battle Creek 6580
Rockford 6840 Detroit 6290
Springfield 5530 Flint 7200
Marquette 8390
Indiana Traverse City 7700
Fort Wayne 6220

56
 CH. 7 - FUEL CONSUMPTION AND ENERGY COST

HEATING DEGREE DAYS (SAMPLING) USA/CANADA

STATE/PROVINCE/CITY D.D. STATE/PROVINCE/CITY D.D.

Minnesota New York
Duluth 9890 Albany 6900
International Falls 10600 Binghamton 7340
Minneapolis/St. Paul 8250 Buffalo 6960
NYC-Central Park 4880
Poughkeepsie 5820
Missouri
Syracuse 6720
Kansas City 4750
St. Louis 4900 North Carolina
Ashville 4130
Montana
Billings 7150 North Dakota
Butte 9730 Bismark 8960
Helena 8190 Fargo 9250

Nebraska Ohio
Lincoln 6050 Cleveland 6200
Omaha 6290 Columbus 5670

Nevada Pennsylvania
Reno 6150 Harrisburg 5280
Johnstown 7804
New Hampshire Philadelphia 5180
Berlin 8270 Pittsburgh 5950
Concord 7360 Scranton/Wilkes-Barre 6160
Manchester 7100
Rhode Island
New Jersey Providence 5950
Atlantic City 4810
Newark 4900 South Dakota
Trenton 4980 Aberdeen 8620
Pierre 7550
New Mexico
Albuquerque 4250 Utah
Santa Fe 6120 Logan 6750
Salt Lake City 5990

57
 CH. 7 - FUEL CONSUMPTION AND ENERGY COST

HEATING DEGREE DAYS (SAMPLING) USA/CANADA

STATE/PROVINCE/CITY D.D. STATE/PROVINCE/CITY D.D.

Vermont Manitoba
Burlington 8030 Winnipeg 10679
Rutland 7440
New Brunswick
Virginia Saint John 8453
Lynchburg 4166
Richmond 3910 Newfoundland
Roanoke 4150 Gander 9254
Winchester 4780 St. John’s 8991

Washington Northwest Terr.

Seattle-Tacoma 5190 Resolute 22673
Spokane 6770 Yellowknife 15634

West Virginia Nova Scotia

Charleston 4510 Halifax 7361
Morgantown 5100 Sydney 8049
Wheeling 5220
Ontario
Wisconsin London 7349
Green Bay 8100 Thunder Bay 10405
Milwaukee 7470 Toronto 6827
Wausau 8490 Windsor 6579

Wyoming Prince Edward Island

Casper 7510 Charlottetown 8486
Cheyene 7370
Quebec
Alberta Montreal 8213
Calgary 9703 Quebec 8937
Edmonton 10268
Saskatchewan
British Columbia Regina 10806
Kamloops 6799 Saskatoon 10856
Vancouver 5515
Victoria 5579 Yukon Territory
Whitehorse 12475

58
 CH. 7 - FUEL CONSUMPTION AND ENERGY COST

HOME HEATING COST

COMPARISON BETWEEN BOILER AND FURNACE
Fuel Consumption for Heating Systems Using Gas and Oil*
OIL HEAT-Gallons burned per year at the indicated heat-loss
(approx.) Hydronics
Heat Loss Hydronics Warm Air Savings Per Year
(Btuh)** (gallons) (gallons) (gallons)
20,000 490 581 91
30,000 734 871 137
40,000 979 1,161 182
50,000 1,224 1,452 228
60,000 1,469 1,742 273
70,000 1,714 2,032 319
80,000 1,958 2,323 364
90,000 2,203 2,613 410
100,000 2,448 2,903 455
110,000 2,693 3,194 501
120,000 2,938 3,484 546

GAS HEAT-Therms burned per year at the indicated heat-loss

(approx.) Hydronic
Heat Loss Hydronic Warm Air Savings Per Year
(Btuh)** (therms) (therms) (therms)
20,000 676 801 126
30,000 1,014 1,202 188
40,000 1,351 1,603 251
50,000 1,689 2,003 314
60,000 2,027 2,404 377
70,000 2,365 2,804 440
80,000 2,703 3,205 502
90,000 3,041 3,606 565
100,000 3,378 4,006 628
110,000 3,716 4,407 691
120,000 4,054 4,808 754
*Hydronics = Circulating hot water with boiler and baseboard.

Warm Air = Blower system with furnace, ducts and registers.

**Calculated heat loss per hour in BTU’s.

59
 CH. 7 - FUEL CONSUMPTION AND ENERGY COST

NOTE: The average fuel saving is 18.6% for Hydronic systems over
Warm air systems.
Hydronic system efficiency - DOE Minimum seasonal efficiency (AFUE)
80%1 - Piping Losses 7½%2 = 74% System Efficiency
Warm air system efficiency - DOE Minimum seasonal efficiency (AFUE)-
78%3 - Duct losses 20%4 = 62.4% System Efficiency
To determine the actual dollar savings, multiply the cost of a gallon of oil
or a therm of gas, for your area, times gallons or therms saved.
1. Department of Energy Minimum Seasonal Efficiency (AFUE)
for boilers as of January 1, 1992
2. “Summary Cooperative Research of Hydronic Heating and
Cooling,” University of Illinois, 1968
3. Department of Energy Minimum Seasonal Efficiency (AFUE)
for furnaces, as of January 1, 1992
4. “Air Conditioning, Heating and Refrigeration News,”
February 19, 1973
Example #1: Using Oil
For a hydronically-heated oil-fueled home, with a heat loss of 40,000
Btuh: 40,000 heat loss house divided by 138,000 Btu/gallon for oil
divided by .74 (system efficiency) x 2500 hours = 979 gallons used.
For a warm air-heated oil fueled home, with a heat loss of 40,000 Btuh:
40,000 heat loss house divided by 138,000 Btu/gallon for oil divided
by .624 (system efficiency) x 2500 hours = 1,161 gallons used.
Example #2: Using Gas
For a hydronically-heated gas-fueled home, with a heat loss of 40,000
Btuh: 40,000 heat loss house divided by 100,000 Btu/therm for gas
divided by .74 (system efficiency) x 2500 hours = 1,351 therms used.
For a warm air-heated gas-fueled home, with a heat loss of 40,000
Btut: 40,000 heat loss house divide by 100,000 Btu/therm for gas
divided by .624 (system efficiency) x 2500 hours = 1,603 therms used.
NOTE: For the Northeast and Upper Midwest there are approximately
2,500 heat loss hours per year. (From GAMA “Consumers’ Directory of
Certified Efficiency Ratings,” April, 1992)
CREDITS: Published by the Better Heating-Cooling Council. Reprinted
with permission of the Hydronics Institute, Berkeley Heights, NJ.

60
 CHAPTER 8 - VALVES: TYPES AND APPLICATIONS

Gate Valve Has a wedge-shaped Ball Valve Its operating device

disc that is raised to open and low- consists of a ball with a hole through
ered to close the valve. It is used its center. The valve operator ro-
either fully open or totally closed tates 90 degrees from fully open to
and is not designed for throttling. the fully closed position. Its major
application is isolation but can be
used to regulate flow.

Globe Valve Uses a round disc or Butterfly Valve Has a wafer-

tapered plug-type disc that seats shaped body with a thin, rotating
against a port to close the valve. disc closing device. Like the ball
Globe valves are used where throt- valve, the butterfly operates with a
tling and/or when frequent opera- one-quarter turn to go full open to
tion is required. closed. The disc is always in the flow
but the disc is thin and offers little
flow restriction.

Angle Valve Operates the same as Swing Check Valve Has a hinged
globe valve. Has less resistance to disc that swings on a hinge pin.
flow than its globe counterpart and When the flow reverses, the pres-
by design acts as a 90° elbow, sure pushes the disc against a seat
eliminationg the need for a fitting. preventing back flow.
61
 CHAPTER 8 - VALVES: TYPES AND APPLICATIONS

Lift Check Valve Has a guided disc Plug Valve Uses a tapered cylin-
that rises from its seat by upward drical plug that fits a body seat of
flow pressure. Flow reversal pushes corresponding shape. A one-quar-
the disc down against its seat, stop- ter turn (90°) operates the valve
ping back flow. Though the lift from open to close. Valve plugs
check has greater flow resistance may be lubricated or non-lubricated.
than the swing check, it is more
suitable for rapid operation cycles.

APPLICATION
Principle Full Allowable
Valve Service Open-Flow Throttling Closure Frequency Positive
Type Function Fesistance Application Speed of Operation Shut-off
Gate Isolation Low Unacceptable Slow Low Poor
Flow
Globe High Good Moderate Moderate Good
regulation
Flow Medium-
Angle Good Moderate Moderate Good
regulation high
Ball Isolation Low Fair Fast High Good
Fair to
Butterfly Isolation Low Fast High Good
good
Flow-
Swing
reversal Low N/A Fast Low Poor
check
control

Flow-
Lift
reversal High N/A Moderate Moderate Fair
check
control
Flow
Good to
Plug regulation/ Low Fast Moderate Good
excellent
isolation

62
 CH. 9 - STANDARD DRAWINGS USED IN HEATING

CONNECTIONS

from top

Connections
to Mains from side

from bottom

Drop in Main

Rise in Main

FITTINGS

Pipe Flange

Union

Strainer

MISCELLANEOUS

Pump

Hot Water In-Line Vacuum Condensation

Tank Tank - Designate Type

Thermostat

63
 CH. 9 - STANDARD DRAWINGS USED IN HEATING

PIPING

Anchor

Condensate Discharge

Dry Return

Eccentric Reducer

Expansion Joint

First Floor Radiation

Hanger or Support

High Pressure Steam

Low Pressure Steam

Medium Pressure Steam

Reducer

Riser and Designation Number

Vacuum Vent Line

Wet Return

64
 CH. 9 - STANDARD DRAWINGS USED IN HEATING

RADIATION

Fin Tube Radiation

Heat Transfer Surface

Unit Heaters
Propeller Fan Type Centrifugal Fan Type

Horizontal Vertical

Unit Ventilator

Unit Ventilator - Auditorium Type

TRAPS
Alternates

Float Trap

Float and
Thermostatic
Trap
Thermostatic
Trap

65
 CH. 9 - STANDARD DRAWINGS USED IN HEATING

VALVES Alternates

Angle

Ball

Butterfly Valve

Check Valve

Three Way

Diaphragm Valve

Four Way

Gate Valve

Globe Valve

Plug Valve

Motor Operated Valve

Pressure Reducing Valve

Relief Valve

66
 CHAPTER 10 - VENTING FLUE PRODUCTS

A. ACCEPTABLE VENTING MATERIAL

Type Temperature Application

AL29-4C ® 100°F to 480°F Pressure vented

(Proprietary stainless gas equipment
steel pipe)

Single-wall metal pipe Refer to codes and Aluminum,

to manufacturer’s galvanized steel
recommendations or stainless
steel; depending
on the
application (1)

B and BW vent To 550°F Gas equipment

L vent To 1000°F Oil equipment (1)

Factory-built chimney 500°F to 2,200°F Oil or gas-fired

equipment (1)

Masonry chimney Gas or oil

(tile liner and air space) 360°F to 1,800°F equipment
(metal liner may
be required.) (2)

(1) Stainless-steel vents can resist the heat that is associated with oil-
fired vent gases, but when the inner wall temperature is below
250°F, it loses its ability to resist acidic damage.

(2) Masonry chimneys also are susceptible to acidic damage.

67
 CHAPTER 10 - VENTING FLUE PRODUCTS

B. METAL VENTS

Type Description

“B” Double-wall round gas vent pipe with a

relatively low permissible temperature of
vent gases.

“BW” Double-wall oval gas vent pipe designed to

fit within a conventional stud wall.
Same application as Type “B”.

“L” Double-wall round stainless steel insulated.

Type “L” is rated for higher temperature vent
gas than the Type “B”. Type “L” may be used
in lieu of “B” but not vice versa.

“C” Single-wall galvanized

IMPORTANT:

VENTING GUIDE FOR ALL BURNHAM RESIDENTIAL GAS

BOILERS -- SEE PAGE 109

68
 CHAPTER 10 - VENTING FLUE PRODUCTS

C. VENTING CATEGORIES: GAS-FIRED EQUIPMENT

Operating
characteristics Category I Category II Category III Category IV

Pressure in the vent Negative Negative Positive Positive

Temperature of Above Below Above Below
vent gas (4) 275°F 275°F 275°F 275°F
Annual efficiency Below 84% Above 84% Below 84% Above 84%
Condensation Not acceptable Possible Possible In heat
(1) (in vent) (3) exchanger
Design requirements
Gas (air) tight vent No No Yes Yes
Corrosion-resistant No (1) Yes Possible (3) Yes
vent (water tight)
Vent into Permitted No No No
masonry chimney (1) and (2)
Combined venting Permitted No No No
Condensate drain No Ask Possible (3) Yes
manufacturer (At
equipment)
Source of N.F.G.C. Manufact. Manufact. Manufact.
information Fuel gas code, literature literature literature
heating equipment
and vent system
manufacturers

NOTE 1 Usually, there is no problem when ing on the ambient temperature and the
high vent gas temperature equipment is conductivity of the vent walls. In this
vented into double-wall vent or into a case, design a vent system that minimizes
lined masonry chimney; but condensation the wall losses (use insulated pipe and
could occur if mid-efficiency (80% to 84%) avoid long runs through cold spaces). A
mechanical draft equipment is vented into corrosion-resistant flue and a drain may be
a vent that has highly conductive walls, required if condensation cannot be pre-
cold walls, or massive walls. In this case, vented — refer to the manufacturer’s rec-
design a vent system that minimizes the ommendations.
wall losses (use double-wall pipe for the NOTE 4 The dewpoint of the vent gas
whole run and avoid long runs through depends on the fuel (natural or LP gas),
cold spaces). the amount of excess air and the amount of
NOTE 2 Install either a rigid or flexible dilution air. The limiting case occurs when
metal liner inside of the masonry chimney the dewpoint of the vent gas is at a maxi-
and use a double-wall connector when mum, which is about 135°F. This maximum
venting mid-efficiency (80% to 84%), me- is produced when natural gas is burned
chanical draft equipment. with no excess air or dilution air. There-
NOTE 3 Condensation in the vent is pos- fore 275°F = 135°F dewpoint + 140°F
sible with some types mid-efficiency (80% rise.
to 84%), direct-vent equipment, depend-

69
 CHAPTER 11 - BASIC ELECTRICITY FOR HEATING

A. UNITS OF ELECTRICAL MEASUREMENT

· VOLTAGE: In order for current to flow in any conductor there
must be an excess of electrons at one point and a
deficiency of electrons at another point. The
amount of difference between the two points is
called “potential" or "voltage”.
· AMPERES: current flow
· OHMS: resistance or “voltage drop” through a conductor
· WATTS: amount of power (volts multiplied by amperes)
Watts = Amps x volts
Volts = watts ÷ amps
Amps = watts ÷ volts
Note: For convenience, magnitude of any of the above is ex-
pressed with the following prefixes:
KILO = 1,000 (one kilowatt = 1,000 watts)
MEG(A) = 1,000,000 (one megohm = 1,000,000 ohms)
MILLI = 1,000 divisor (one millivolt = 1/1,000th of
a volt)
MICRO = 1,000,000 divisor (one microampere =
1/1,000,000th of an ampere)

B. DIRECT CURRENT AND ALTERNATING CURRENT

· Direct Current (D.C.) is a continuous current that always flows
in the same direction.
· Alternating Current (A.C.) is a current that periodically “cycles”,
or reverses its direction of flow. The number of complete cycles
that occur in one second is the frequency of the current.
· Commercially produced power, and the utilization equipment
for use on commercial power, is almost universally A.C.

C. MOTORS (TYPES)
· Universal: Essentially a D.C. motor modified to run on A.C.
Primarily used in small household appliances (mix-
ers, shavers, small power tools). Single phase only.

70
 CHAPTER 11 - BASIC ELECTRICITY FOR HEATING

· Capacitor Start/Induction Run: Has good torque characteris-

tics and is used in heavy duty applications such as
pumps, blowers, and large power burners.
· Shaded Pole: The simplest of all A.C. motors, it operates only
on single phase current. Is available in sizes up to and
including 1/3 H.P. It has no brushes or commutator.
Has very low starting torque and therefore should not
be used on equipment that is hard to start in motion.
Some typical applications are small fans, heater
blowers, etc.
· Split Phase: Has starting windings and a centrifugal switch.
Its simplicity, good torque, and rugged construction
give it a wide range of fractional horsepower
applications.

D. TRANSFORMERS
· A transformer transfers power from one circuit to another
circuit of different voltage, without an electrical connection
between the two circuits.
· Input of a transformer must be A.C. current, and the output will
also be A.C. current.
· A step-up transformer increases voltage but the available
amperage decreases. A step-down transformer decreases
voltage but the available amperage increases.
· The safe load rating of a transformer is expressed in VA. The
actual power drawn depends on the connected load.

E. RELAYS
An electromagnetic switching device that can perform switching action
in two or more circuits that have no electrical connection.
Relay Terminology
Relays are referred to as "single-pole-single throw", "single pole-double
throw", "double pole-single throw", etc.
The poles are stationary and are usually used for power input. The arms
extending from the poles of each switch or relay are mechanically linked
together but are independent of each other electrically.

71
 CHAPTER 11 - BASIC ELECTRICITY FOR HEATING

Relay Terminology (con't)

The arms extending from each pole include a moveable contact. the
number of throws is the number of positions in which the moveable
contact, connected to each pole, can complete a circuit. See examples
below:

SPST SPDT

DPST 3PDT
The dotted lines indicate that the arms are mechanically linked and will
move together.
• Normally open, Normally closed: refers to the position of the
switch contacts when the magnetic coil is not energized.
Relay Types
1. Time delay relay: incorporates a means for delaying the opening
or closing of the load contacts for a specific period of time after the
control circuit is energized or de-energized.
2. Transfer relay: incorporates overlapping load contacts that permit
the load to be transferred from one circuit to another when the coil
is energized.
3. Transformer relay: incorporates a step-down transformer to
power the low voltage control circuit.
4. Alarm silencing relay: incorporates contacts arranged to silence an
audible alarm when a push button is depressed, without re-
establishing the main load circuit to the controlled device.
5. Contactor: a heavy duty relay for control of motors or high
amperage loads. May incorporate auxiliary holding contacts for
interlocking with safety limits or other devices.
72
 CHAPTER 11 - BASIC ELECTRICITY FOR HEATING

6. Balancing relay: used in bridge circuits to equalize resistance values.

7. Overload relay: opens the load circuit if current drawn exceeds a
selected value (“magnetic overload relay”) or in response to heat
generated by excessive current flow (“thermal overload relay”).
F. SWITCHES
· Switches are used to open (break) or complete (make) a circuit.
· Switches may be actuated manually, by heat, mechanically, or
electromagnetically.
· Switches are identified by the number of poles provided, and
whether they are single throw or double throw.
G. OVERLOAD PROTECTION
· Fuses and circuit breakers are used in the power circuit to protect
against damage from a short circuit (circuit failure that permits
the current to take a shortcut between the terminals of a power
source).
· Motors have their own overload protection in addition to power
circuit overload protection.

H. ELECTRIC SERVICE
· Single Phase Two Wire: residential service to older buildings,
seldom used in new construction. Provides power at 115 volts.
· Single Phase Three Line: residential and light commercial
service universally used in new construction. Provides power
at 115/230 volts.
· Three Phase Three Wire: commercial/industrial service.
Provides power at a number of nominal supply voltages (240,
480 or 600 volts; sometimes 220, 440 or 550 are available).
· Three Phase Four Wire: commercial/industrial service.
Provides power at nominal system voltages of 208, 416 or 480
volts.
CAUTION: The above description is oversimplified but electrical
characteristics of heating equipment must be compatible with the
available power supply.

73
 CHAPTER 12 - HEATING INDUSTRY ACRONYMS

BUILDING CODES & STANDARDS

ANSI American National Standards Institute

11 West 42nd St., New York, NY 10036

ASHRAE American Society of Heating, Refrigeration and Air

Conditioning Engineers, Inc.
1791 Tullie Circle NE, Atlanta, GA 30329

BOCA Building Officials & Code Administrators International, Inc.

4051 W. Flossmoor Rd., Country Club Hills, IL 60477

CABO Council of American Building Officials

5203 Leesburg Pike, Suite 708, Falls Church, VA 22041

IAPMO International Association of Plumbing & Mechanical

Officials
20001 South Walnut Dr., Walnut, CA 91789

ICBO International Conference of Building Officials

5360 South Workman Mill Rd., Whittier, CA 90601

NBS National Bureau of Standards

Washington, DC 20234

NCSBCS National Conference of States on Building Codes and

Standards, Inc.
481 Carlisle Drive, Herndon, VA 22070

NFPA National Fire Protection Association

Batterymarch Park, P.O. Box 9101, Quincy, MA 02269

SBCCI Southern Building Code Congress International, Inc.

900 Montclair Rd., Birmingham, AL 35213

PROFESSIONAL ASSOCIATIONS & SOCIETIES

ABMA American Boiler Manufacturers Association

950 N. Glebe Rd., Suite 160, Arlington, VA 22203

ACCA Air Conditioning Contractors of America

1513 16th Street NW, Washington, DC 20036
(formerly National Environmental Systems Contractors
Association)

ARI Air-Conditioning and Refrigeration Institute

1501 Wilson Blvd., Suite 600, Arlington, VA 22209

ASGE American Society of Gas Engineers

P.O. Box 31756, Independence, OH 44131
74
 CHAPTER 12 - HEATING INDUSTRY ACRONYMS

BHC Better Heating-Cooling Council

P.O. Box 218, Berkeley Heights, NJ 07922
GAMA Gas Appliance Manufacturers Association, Inc.
1901 N. Moore St., Suite 1100, Arlington, VA 22209
GRI Gas Research Institute
8600 W Bryn Mawr Ave., Chicago, IL 60631
HYDI Hydronics Institute
35 Russo Place, Berkeley Heights, NJ 07922
MCAA Mechanical Contractors Association of America, Inc.
1385 Piccard Drive, Rockville, MD 20850
NAPHCC National Association of Plumbing-Heating-Cooling
Contractors
180 S Washington St., P.O. Box 6808, Falls Church, VA
22040
RSES Refrigeration Service Engineeers Society
1666 Rand Rd., Des Plaines, IL 60016
SMACNA Sheet Metal and Air Conditioning Contractors’
National Assoc.
8224 Old Courthouse Rd., Vienna, VA 22180
APPROVAL AGENCIES
ETL/ETLc Intertech Testing Services
18 Boulden Circle, Suite 34, New Castle, DE 19720
AGA American Gas Association
1515 Wilson Blvd., Arlington, VA 22209
CGA Canadian Gas Association
55 Scarsdale Rd., Toronto, Ontario M3B 2R3
IAS International Approval Services
Joint Venture of AGA and CGA (effective 1/1/96)
Offices in Cleveland, OH, Los Angeles, CA,
and Toronto, Ontario
ASME American Society of Mechanical Engineers
345 East 47th St., New York, NY 10017
CSA Canadian Standards Association
178 Rexdale Blvd., Rexdale, ONT M9W 1R3, Canada
IBR Institute of Boiler and Radiator Manufacturers
superseded by Hydronics Institute
UL Underwriters’ Laboratories, Inc.
333 Pfingsten Rd., Northbrook, IL 60062

75
 CHAPTER 13 - THE METRIC SYSTEM

The metric system, a European system of measurement, was developed

by the French during the latter part of the 18th century to standardize
measurement units. By the end of the 19th century it was being used as
a commercial unit of measure by most European nations as well as
Central and South America.
The system is not new to the United States. As early as 1790 Thomas
Jefferson had suggested its use. In 1866 an Act of Congress made the
metric measure legal but not mandatory. Since World War II many other
nations have changed to metric: Russia, The Peoples Republic of China,
India, Japan, The United Kingdom, Germany, Mexico and Canada.
1. THE METRIC UNITS:
LENGTH:
The base unit of metric length is the meter -- this unit is 39.37 inches
and is divided into one hundred centimeters. The meter is one
thousandth part of the kilometer which is the unit that will replace
the mile.
Symbols:
Millimeter mm
Centimeter cm
Decimeter dm
meter m
Kilometer km = 1,000 m.

AREA:
The base unit of metric area is the square meter -- this unit is one
ten thousandth part of a hectare. The hectare is approximately 2½
acres in area and will probably replace the acre as a basis for land
surveys.
Symbols:
Square centimeter cm²
Square decimeter dm²
Square meter m²
are a
hectare ha
Square kilometer km² = 100 ha.

76
 CHAPTER 13 - THE METRIC SYSTEM

VOLUME:
The base unit of metric volume is the liter -- this unit is 1.8 fl. ounces
larger than the U.S. Quart. Drug dispensers prefer to work with
cubic centimeters or milliliters as the unit is also known. One
teaspoon is the equivalent of 5 milliliters. For measuring larger
quantities, e.g. readymix concrete, cubic meters is the unit used.
Symbols:
Cubic centimeter cm3 or cc. as it is commonly
referred to milliliter ml
cubic decimeter dm3
liter l
cubic meter m3 = 1,000 l
WEIGHT/MASS:
The base unit of metric weight is the gram -- this unit is approxi-
mately one thirtieth of an avoirdupois ounce and is mostly used in
pharmaceutical and scientific work. The more convenient unit is
the kilogram, weighing approximately 2.2 pounds.
Symbols:
milligram mg
gram g
Kilogram kg
Metric ton t = 1,000 kg.
TEMPERATURE:
Most countries using the Metric System use the Celsius (formerly
centigrade) thermometer where water freezes at 0°C and boils at
100°C. Comfortable room temperature would be about 22°C and
body temperature 37°C.
Temperature conversion from Fahrenheit to
Celsius (Centigrade):
The simple formula is: Fahrenheit to Celsius = (F° - 32°) ÷ 1.8
Celsius to Fahrenheit = C° x 1.8 + 32

77
 CHAPTER 13 - THE METRIC SYSTEM

°Fahrenheit °Celsius
Boiling Point of Water 212.0 100
167.0 75
122.0 50
104.0 40
Body Temperature 98.6 37
95.0 35
85.0 30
77.0 25
Comfortable Room Temp. 72.0 22.2
68.0 20
59.0 10
50.0 10
41.0 5
39.2 4
37.4 3
35.6 2
33.8 1
Freezing Point of Water 32 F 0C

2. TABLES OF METRIC WEIGHTS AND MEASURES:

LINEAR MEASURE (LENGTH):
10 millimeters (mm) = 1 Centimeter (cm)
10 centimeters = 1 Decimeter (dm)
= 100 millimeters
10 decimeters = 1 Meter (m)
= 1,000 millimeters
10 meters = 1 Dekameter
10 dekameters = 1 Hectometer (hm)
= 100 meters
10 hectometers = 1 Kilometer (km)
= 1,000 meters

SQUARE MEASURE (AREA):

100 Square Millimeters = 1 Sq. Centimeter (cm²)
10,000 Square Centimeters = 1 Square Meter (m²)
100 Square meters = 1 Are (a)
100 Ares = 1 Hectare (ha)

78
CHAPTER 13 - THE METRIC SYSTEM

100 Hectares = 1 Square kilometer (km²)

= 1,000,000 square meters

VOLUME MEASURE:
1 milliliter = 1 cubic centimeter
(cm3 or cc)
1 liter = 0.001 cubic meter
10 milliliters (ml) = 1 Centiliter (cl)
10 centiliters = 1 Deciliter (dl)
= 100 milliliters
10 deciliters = 1 Liter (l)
= 1,000 milliliters
10 liters = 1 dekaliter
10 dekaliters = 1 Hectoliter (hl)
= 100 liters
10 hectoliters = 1 kiloliter
= 1,000 liters

CUBIC MEASURE (CAPACITY):

1,000 cubic millimeters = 1 cubic centimeter
(cm3 or cc)
1,000 cubic centimeters = 1 cubic decimeter
= 1,000,00 cubic
millimeters
= 1 liter
1,000 cubic decimeters = 1 cubic meter

WEIGHT MEASURE:
10 milligrams (mg) = 1 centigram (cg)
10 centigrams = 1 decigram (dg)
10 decigrams = 1 gram (g)
10 grams = 1 dekagram
10 dekagrams = 1 hectogram (hg)
10 hectograms = 1 kilogram (kg)
1,000 kilograms = 1 Metric Ton

79
 CHAPTER 13 - THE METRIC SYSTEM

3. MULTIPLES AND SUBMULTIPLES:

Prefix Symbol Equivalent Factor
atto- a quintillionth part x10-18
femto- f quadrillionth part x10-15
pico- p trillionth part x10-12
nano- n billionth part x10-9
micro- µ millionth part x10-6
milli- m thousandth part x10-3
centi- c hundredth part x10-2
deci- d tenth part x10-1
deka da tenfold x10
hecto- h hundredfold x10²
kilo- k thousandfold x103
mega- M millionfold x106
giga- G billionfold x109
tera- T trillionfold x1012

The small figure in the factor determines the position of

the decimal point in multiplying out a conversion.
EXAMPLE:
3.0 x 10² = 3.00 x 10 x 10
move decimal point 2 places to the right
= 300.00
6.37 x 103 = 6.37 x 10 x 10 x 10
move decimal point 3 places to the right
= 6370.00
6.37 x 10-3 = .00637
move decimal point 3 places to the left

4. TABLE OF EQUIVALENTS:
LENGTH/DISTANCE:
1 chain (surveyors) = 66 feet
= 20.1168 meters
1 fathom = 6 feet
= 1.8288 meters
1 foot = 0.3048 meter
1 inch = 2.54 centimeters
= 25.4 millimeters

80
CHAPTER 13 - THE METRIC SYSTEM

1 mile (statute) = 1.609 kilometers

1 mile (nautical) = 1.151 statute miles
= 1.852 kilometers
1 yard = 0.9144 meter
1 centimeter = 0.3937 inch
1 decimeter = 3.937 inches
1 dekameter = 32.808 feet
1 kilometer = 0.621 mile
1 meter = 1.094 yards
= 39.37 inches
1 millimeter = 0.03937 inch

AREA/SURFACE:
1 acre = 4,840 square yards
= 0.405 hectare
1 square foot = 929.030 square centimeters
1 square inch = 6.4516 square centimeters
1 square mile = 258.999 hectares
1 square yard = 0.836 square meter
1 are = 119.599 square yards
= 0.025 acre
1 hectare = 2.471 acres
1 square centimeter = 0.155 square inch
1 square decimeter = 15.500 square inches
1 square kilometer = 247.105 acres
= 0.386 square mile
1 square meter = 10.764 square feet
= 1.196 square yards
1 square millimeter = 0.002 square inch

CAPACITY/VOLUME:
1 cubic foot = 28.316 cubic decimeters
1 cubic inch = 16.387 cubic centimeters
1 cubic yard = 0.765 cubic meter
1 U.S. gallon = 128 fluid ounces
= 231 cubic inches
= 3.785 liters

81
 CHAPTER 13 - THE METRIC SYSTEM

1 gill = 4 fluid ounces

= 0.118 liter
1 U.S. fluid ounce = 29.574 milliliters
1 U.S. fluid quart = 57.75 cubic inches
= 0.946 liter
1 cubic centimeter = 0.061 cubic inch
1 cubic decimeter = 61.024 cubic inches
1 cubic meter = 1.308 cubic yards
1 cubic dekaliter = 2.642 gallons
1 hectoliter = 26.418 gallons
1 liter = 61.024 cubic inches
1 milliliter = 0.061 cubic inch

WEIGHT/MASS:
1 carat = 200 milligrams
1 gram = 0.035 ounce
1 kilogram = 2.205 pounds
1 Metric Ton = 2,204.623 pounds
1 ounce = 28.35 grams
1 pound = 0.453592 kg

5. UNIT CONVERSIONS
To Convert Into Multiply by
Acre Hectare 0.4047
Astronomical Unit Kilometers 1.495 x 108
Bolt (U.S. cloth
measure) Meters 36.576
B.T.U. Kilowatt Hours 2.928 x 10-4
B.T.U./Hr Watts 0.2931
Centimeters Kilometers 1 x 10-5
Centimeters Meters 1 x 10-2
Centimeters Millimeters 10.00
Centimeters Feet 3.281 x 10-2

82
 CHAPTER 13 - THE METRIC SYSTEM

Centimeters Inches 0.3937

Cubic Centimeters Cubic Inches 0.06102
Cubic Feet Cubic Meters 0.02832
Feet Centimeters 30.48
Feet Meters 0.3048
Feet/Min Centimeters/Sec 0.5080
Foot Pounds Kilowatt Hours 3.766 x 10-7
Gallons Liters 3.785
Grams Ounces 3.527 x 10-2
Grams Pounds 2.205 x 10-3
Hectares Acres 2.471
Hectares Square Feet 1.076 x 105
Horsepower Kilowatts 0.7457
Horsepower Watts 745.7
Inches Centimeters 2.54
Kilograms Pounds 2.205
Kilometers Feet 3,281.00
Kilometers Miles 0.6214
Kilometers/hour Knots 0.5396
Kilowatts Horsepower 1.341
Kilowatt Hours B.T.U. 3,413.00
Liters Cubic Inches 61.02
Liters U.S. Liquid Gallons 0.2642
Liters U.S. Liquid Pints 2.113

83
 CHAPTER 13 - THE METRIC SYSTEM

Meters Feet 3.281

Meters Miles (Nautical) 5.396 x 10-4
Meters Miles (Statute) 6.214 x 10-4
Miles (Nautical) Kilometers 1.853
Miles (Statute) Kilometers 1.609
Millimeters Inches 3.937 x 10-2
Ounces Grams 28.349527
Pounds Kilograms 0.4536
Pounds per Square Grams per Square
Inch (PSI) Centimeter 70.31
Quarts (Liquid) Liters 0.9463
Tons (long) Kilograms 1,016.00
Tons (short) Kilograms 907.1848
Watts B.T.U./hour 3.4129
Watts Horsepower 1.341 x 10-3
Yards Meters 0.914

84
 CHAPTER 14 - MISCELLANEA

ENERGY TERMS - CONVERSIONS - HEAT VALUES

A. PREFIXES
Prefixes indicateorders of magnitude in steps. Prefixes provide a
convenient way to express large and small numbers and to
eliminate nonsignificant digits and leading zeros in
decimal fractions. The following are the more commonly used
prefixes:
English System
Symbol Represents
C 100
M 1,000
MM 1,000,000
Metric System
K 1,000
M* 1,000,000
*Caution: make certain of the system.

B. NATURAL GAS ENERGY MEASUREMENTS IN BTU

1,000 = 1 Cubic Foot
100,000 = 1 therm or 1 CCF or 100 MBTU
1,000,000 = 1 MMBTU or 1,000 CF or 1
MCF
1,000,000,000 = 1 billion BTU or 1 MMCF
1,000,000,000,000 = 1 trillion BTu or 1 BCF
1,000,000,000,000,000 = 1 quadrillion BTU or 1 TCF

C. ENERGY MEASUREMENTS OF OTHER FUELS IN BTU

Propane 2,550 btu = 1 CF
21,650 btu = 1 Lb.
91,800 btu = 1 Gal.
Butane 3,200 btu = 1 CF
21,500 btu = 1 Lb.
102,400 btu = 1 Gal.
Oil 5,825,000 btus = 1 barrel crude
6,200,000 btus = 1 barrel #5 (Residual)
6,400,000 btus = 1 barrel #6 (heating)
134,000 btus = 1 Gal. #1 oil (kerosene)
139,000 btus = 1 Gal. #2 oil
146,800 btus = 1 Gal. #4 oil
150,000 btus = 1 Gal. #6 oil
(1 U.S. Barrel = 42 U.S. Gallons)

85
 CHAPTER 14 - MISCELLANEA

Electric 3,412 btus = 1 Kilowatt

Coal 21,700,000 btus = 1 Ton Bituminous (soft)
22,800,000 btus = 1 Ton Anthracite (hard)
Wood 3,500 btus = 1 Lb. (mixed average)
14,000,000 btus = 1 Cord (mixed average)

D. QUICK FUEL COMPARISONS BASED ON 1,000,000 BTUS

Natural Gas = 10 Therms
Propane Gas = 10.89 Gal.
Butane Gas = 9.77 Gal.
#1 Oil = 7.46 Gal.
#2 Oil = 7.19 Gal.
#4 Oil = 6.81 Gal.
#6 Oil = 6.67 Gal.
Bituminous Coal = .046 Ton (92 Lbs.)
Anthracite Coal = .044 Ton (88 Lbs.)
Wood (mixed avg)= 286 Lbs.

E. SPECIFIC HEATING VALUE OF WOODS

(Based on U.S. Dept. of Agriculture Bulletin No. 753)

Equivalent lb.
of Coal of
Weight Heating Value 13,500 BTU
per cord. lb. BTU per lb. per lb.
Green Air-dry Green Air-dry Green Air-Dry
Ash-white 4300 3800 4628 5395 0.343 0.400
Beech 5000 3900 3940 5359 0.292 0.397
Birch, yellow 5100 4000 3804 5225 0.282 0.387
Chestnut 4900 2700 2633 5778 0.195 0.428
Cottonwood 4200 2500 3024 6000 0.224 0.444
Elm, white 4400 3100 3591 5710 0.266 0.423
Hickory 5700 4600 4053 5391 0.300 0.399
Maple, sugar 5000 3900 4080 5590 0.302 0.414
Maple, red 4700 3200 3745 5969 0.277 0.442
Oak, red 5800 3900 3379 5564 0.250 0.412
Oak, white 5600 4300 3972 5558 0.294 0.412
Pine, yellow 3100 2300 7079 9174 0.526 0.680
Pine, white 3300 2200 4226 5864 0.313 0.434
Walnut, black 5100 4000 4078 4650 0302 0.344
Willow 4600 2300 2370 5870 0.176 0.435

A cord of Wood is a pile 4' x 4' x 8' = 128 cu. ft. comprising approxi-
mately 56% Solid wood and 44% Interstitial spaces.

86
 CHAPTER 14 - MISCELLANEA

MEASURING GAS & OIL INPUT

Gas on pages 85 and 86 - Oil on page 87
1. GAS RATE - CUBIC FEET PER HOUR
Seconds Size of Test Dial Seconds Size of Test Dial
for One for One
Revolution 2 cu. ft. 5 cu. ft. Revolution 2 cu. ft. 5 cu. ft.
10 720 1800 55 131 327
11 655 1636 56 129 321
12 600 1500 57 126 316
13 555 1385 58 124 310
14 514 1286 59 122 305
15 480 1200 60 120 300
16 450 1125 62 116 290
17 424 1059 64 112 281
18 400 1000 66 109 273
19 379 947 68 106 265
20 360 900 70 103 257
21 343 857 72 100 250
22 327 818 74 97 243
23 313 783 76 95 237
24 300 750 78 92 231
25 288 720 80 90 225
26 277 692 82 88 220
27 267 667 84 86 214
28 257 643 86 84 209
29 248 621 88 82 205
30 240 600 90 80 200
31 232 581 92 78 196
32 225 563 94 192
33 218 545 96 75 188
34 212 529 98 184
35 206 514 100 72 180
36 200 500 102 176
37 195 486 104 69 173
38 189 474 106 170
39 185 462 108 67 167
40 180 450 110 164
41 176 439 112 64 161
42 172 429 116 62 155
43 167 419 120 60 150
44 164 409 125 144
45 160 400 130 138
46 157 391 135 132
47 153 383 140 129
48 150 375 145 124
49 147 367 150 120
50 144 360 155 116
51 141 353 160 113
52 138 346 165 109
53 136 340 170 106
54 133 333 175 103
55 131 327 180 100
87
 CHAPTER 14 - MISCELLANEA

Seconds Size of Test Dial Seconds Size of Test Dial

for One for One
Revolution 1/2 cu. ft. 1 cu. ft. Revolution 1/2 cu. ft. 1 cu. ft.
10 180 360 35 103
11 164 327 36 50 100
12 150 300 37 97
13 138 277 38 47 95
14 129 257 39 92
15 120 240 40 45 90
16 113 225 41
17 106 212 42 43 86
18 100 200 43
19 95 189 44 41 82
20 90 180 45 40 80
21 86 171 46 78
22 82 164 47 38
23 78 157 48 75
24 75 150 49
25 72 144 50 36 72
26 69 138 51
27 67 133 52 69
28 64 129 53 34
29 62 124 54 67
30 60 120 55
31 116 56 32 64
32 56 113 57
33 109 58 31 62
34 53 106 59
35 103 60 30 60

88
 CHAPTER 14 - MISCELLANEA

2. OIL RATE -- GALLON PER HOUR

Nozzle Delivery Rates at Various Pressures for No. 2 Fuel Oil

Pump Pressure (PSI)

80 90 100 125 150 175 200 225 250 275 300
1.0 0.9 .95 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.75
1.5 1.3 1.4 1.5 1.7 1.8 2.0 2.1 2.3 2.4 2.5 2.6
2.0 1.8 1.9 2.0 2.2 2.5 2.6 2.9 3.0 3.2 3.3 3.5
2.5 2.2 2.4 2.5 2.8 3.1 3.3 3.5 3.8 4.0 4.1 4.3
3.0 2.7 2.8 3.0 3.3 3.7 3.9 4.2 4.5 4.7 5.0 5.2
3.5 3.1 3.3 3.5 3.9 4.3 4.6 5.0 5.3 5.5 5.8 6.0
4.0 3.6 3.8 4.0 4.5 4.9 5.3 5.6 6.0 6.3 6.6 6.9
4.5 4.0 4.2 4.5 5.0 5.5 5.9 6.3 6.8 7.1 7.4 7.8
5.0 4.5 4.7 5.0 5.6 6.1 6.6 7.1 7.5 7.9 8.3 8.7
5.5 4.9 5.2 5.5 6.2 6.7 7.3 7.8 8.3 8.7 9.1 9.5
6.0 5.3 5.6 6.0 6.7 7.3 7.9 8.5 9.0 9.5 9.9 10.4
7.0 6.2 6.6 7.0 7.8 8.5 9.2 9.9 10.5 11.0 11.6 12.0
8.0 7.2 7.5 8.0 8.9 9.8 10.5 11.3 12.0 12.6 13.2 13.8
9.0 8.0 8.5 9.0 10.0 11.0 11.8 12.6 13.5 14.2 14.8 15.6
10.0 8.4 9.4 10.0 11.2 12.2 13.2 14.1 15.0 15.8 16.6 17.3
11.0 9.8 10.3 11.0 12.3 13.4 14.5 15.6 16.5 17.4 18.2 19.0
12.0 10.7 11.2 12.0 13.4 14.6 15.8 16.9 18.0 18.9 19.8 20.7
13.0 11.6 12.2 13.0 14.5 16.0 17.2 18.4 19.5 20.6 21.5 22.5
14.0 12.4 13.1 14.0 15.6 17.0 18.4 19.8 21.0 22.0 23.1 24.0
15.0 13.3 14.0 15.0 16.8 18.4 19.8 21.3 22.5 23.6 24.8 25.9
16.0 14.3 15.0 16.0 17.8 19.5 21.0 22.6 24.0 25.3 26.4 27.7
17.0 15.1 15.9 17.0 19.0 20.7 22.5 24.1 25.5 26.9 28.0 29.3
18.0 16.1 17.0 18.0 20.1 22.0 23.7 25.3 27.0 28.4 29.7 31.2
20.0 17.8 18.8 20.0 22.3 24.4 26.4 28.2 30.0 31.7 33.1 34.6
22.0 19.6 20.6 22.0 24.6 26.9 29.0 31.2 33.0 34.8 36.4 38.0

Notes: These delivery rates are approximate values.

Actual rates will vary slightly between different nozzles of

the same nominal rating.

Delivery tends to increase with higher viscosity, or lower oil

temperature, or lower specific gravity.

89
 CHAPTER 14 - MISCELLANEA

ACIDITY AND ALKALINITY - (pH)

pH is the logarithm of the reciprocal of the Hydrogen concentration.

pH = log10 1 (gram/liter equiv.)

H+

Since 1 hydroxyl ion is formed whenever a hydrogen ion develops, the pH

scale also is used to measure the formation of hydroxyl ions.

Typical pH values, relative strength:

1 1,000,000 1/10 normal HCl sol

2 100,000 Gastric Fluid
3 10,000 Vinegar (4% acetic acid)
4 1,000 Orange or grape juice
5 100 Molasses
6 10 Milk (6.8 pH)
7 1 Pure Water, saliva
8 10 Baking Soda, sea water
9 100 Borax solutioin
10 1,000 Soap - Milk of magnesia
11 10,000 Tri-sodium phosphate
12 100,000 Household ammonia (10%)
13 1,000,000 Lye - Na O H

Manufacturers of hydronic and air conditioning equipment recommend a pH

value of 7.5 to 8.5 in the circulating water.
The pH levels in all industrial cooling and heating systems are closely
supervised. Excessive acidity (pH 5-6) causes corrosion and high alkalinity
(pH 8-10) results in heavy scale deposits on hot heat transfer surfaces.

SOUND LEVELS
The human ear can accept an enormous range of sound levels. From a whisper
(20 dB) to a police siren at 50 ft. (120dB) represents a sound pressure level
ratio of 1 to 1 million. The ear can take it for short periods, but prolonged
exposure to high noise levels will cause permanent hearing impairment.
Because of the very large audio level ratios and resulting cumbersome
numbers, the decibel system was devised.

Honoring Alexander Graham Bell, the telephone industry named the unit
of sound the Bel. This unit was found to be too large for convenience, so
1/10 Bel or the decibel (dB) was adopted internationally.

90
 CHAPTER 14 - MISCELLANEA

TYPICAL SOUND PRESSURE LEVELS

Db Noise Source and Distance

130 Jet plane take-off at 200 ft.

120 Police siren at 50 ft.
110 Pneumatic hammer at 50 ft.
100 Millworking machines at 50 ft.
90 Manufacturing plants, average
80 Symphony orchestra, fortissimo
70 Vacuum cleaner at 10 ft.
60 Business machine areas
50 Normal business offices
40 Quiet residential areas at night
30 Normal speech at 3 ft.
20 Soft whisper at 3 ft.

Doubling of sound pressure from a single source results in a 3 dB rise in sound

pressure level.

Doubling of the distance from the source of a sound to the receiver will reduce
its level 6 dB.

A 10 dB rise in sound level indicates that the sound perceived by the ear will
be twice as loud as the original sound.

A police siren developing 100 dB at 100 ft. will produce 94 dB at 200 ft.; 88
dB at 400 ft., etc.

GAS PIPE SIZING - RESIDENTIAL

Interior gas piping must be examined before installing a new gas boiler. A
typical winter load and even a summer load (indirect hot water supply) must
be considered. Listed below are average inputs of various gas appliances that
may be on-line. Also listed is a chart to determine whether the existing piping
can carry the seasonal load.

For specific appliances or appliances not shown below, the input should be
determined from the manufacturer’s rating.

91
 CHAPTER 14 - MISCELLANEA

Approximate Gas Input for Some Common Appliances

Appliance Input BTU Per Hr.

(Approx.)

Range, Free Standing, Domestic 65,000

Built-In Oven or Broiler Unit, Domestic 25,000
Built-In Top Unit, Domestic 40,000
Water Heater, Automatic Storage - 30 to 40 Gal. Tank 45,000
Water Heater, Automatic Storage - 50 Gal. Tank 55,000
Fireplace/Gas Log 21,000 - 55,000
Grille 30,000 - 40,000
Boiler ----
Clothes Dryer, Type 1 (Domestic) 20,000 - 35,000
Gas Light 2,500
Incinerator, Domestic 35,000

Maximum Capacity of Pipe in Cubic Feet of Gas Per Hour

(Based on a pressure drop of 0.3 Inch Water Column and 0.6 Specific Gravity Gas)
Length Nominal Iron Pipe Size, Inches
In
Feet 1/2 3/4 1 1-1/4 1-1/2 2 2-1/2 3 4
10 132 278 520 1,050 1,600 3,050 4,800 8,500 17,500
20 92 190 350 730 1,100 2,100 3,300 5,900 12,000
30 73 152 285 590 890 1,650 2,700 4,700 9,700
40 63 130 245 500 760 1,450 2,300 4,100 8,300
50 56 115 215 440 670 1,270 2,000 3,600 7,400
60 50 105 195 400 610 1,150 1,850 3,250 6,800
70 46 96 180 370 560 1,050 1,700 3,000 6,200
80 43 90 170 350 530 990 1,600 2,800 5,800
30 40 84 160 320 490 930 1,500 2,600 5,400
100 38 79 150 305 460 870 1,400 2,500 5,100
125 34 72 130 275 410 780 1,250 2,200 4,500
150 31 64 120 250 380 710 1,130 2,000 4,100
175 28 59 110 225 350 650 1,050 1,850 3,800
200 26 55 100 210 320 610 980 1,700 3,500

Correction Factors for Specific Gravity Other Than 0.60

92
 CHAPTER 14 - MISCELLANEA

ABBREVIATIONS USED IN HEATING

Absolute ...................................... abs Gallons per Second ............................... gps

Alternating-Current ..................... a-c Gram ........................................................... g
Ampere ........................................ amp Horsepower ............................................. hp
Atmosphere .................................. atm Horsepower-Hour .............................. hp-hr
Average ........................................ avg Hour .......................................................... hr
Avoirdupois .............................. avdp Inch ............................................................ in
Barometer ...................................... bar Inch-Pound .......................................... in-lb
Boiling Point ............................... bp Kilogram .................................................. kg
Brake Horsepower ...................... bhp Kilowatt ................................................. kw
Brake Horsepower, Hour ...... bhp-hr Melting Point ......................................... mp
British Thermal Unit ................... Btu Meter ......................................................... m
per hour ................................. Btuh Miles per Hour ..................................... mph
Calorie .......................................... cal Millimeter ............................................... mm
Centigram ....................................... cg Minute ................................................... min
Centimeter ..................................... cm Ounce ....................................................... oz
Cubic .............................................. cu Pound ........................................................ lb
Cubic Centimeter ........................... cc Pounds per Square Inch ......................... psi
Cubic Foot .................................. cu ft Pounds per Square Inch, Gage ............ psig
Cubic Feet per Minute .................. cfm Pounds per Square Inch, Absolute ..... psia
Cubic Feet per Second .................. cfs Revolutions per Minute ........................ rpm
Degree .................................. deg or ° Revolutions per Second. ....................... rps
Degree, Centigrade ......................... C Second .................................................... sec
Degree, Fahrenheit .......................... F Specific Gravity .................................. sp gr
Diameter ..................................... diam Specific Heat ........................................ sp ht
Direct-Current ............................ d - c Square Foot ........................................... sq ft
Feet per Minute ........................... fpm Square Inch .......................................... sq in
Feet per Second ............................ fps Volt ............................................................. v
Foot .................................................. ft Watt ........................................................... w
Foot-Pound ................................ ft lb Watt Hour .............................................. whr
Freezing Point ................................ fp
Gallon ........................................... gal
Gallons per Minute .................... gpm

93
 CHAPTER 14 - MISCELLANEA

CAPACITY OF ROUND STORAGE TANKS

Number of Gallons
Depth
or Inside Diameter in Inches
Length
in Ft. 18 24 30 36 42 48 54 60 66 72
1 1.10 1.96 3.06 4.41 5.99 7.83 9.91 12.24 14.81 17.62
2 26 47 73 105 144 188 238 294 356 423
2-1/2 33 59 91 131 180 235 298 367 445 530
3 40 71 100 158 216 282 357 440 534 635
3-1/2 46 83 129 184 252 329 416 513 623 740
4 53 95 147 210 288 376 475 586 712 846
4-1/2 59 107 165 238 324 423 534 660 800 952
5 66 119 181 264 360 470 596 734 899 1057
5-1/2 73 130 201 290 396 517 655 808 978 1163
6 79 141 219 315 432 564 714 880 1066 1268
6-1/2 88 155 236 340 468 611 770 954 1156 1374
7 92 165 255 368 504 658 832 1028 1244 1480
7-1/2 99 179 278 396 540 705 889 1101 1335 1586
8 106 190 291 423 576 752 949 1175 1424 1691
9 119 212 330 476 648 846 1071 1322 1599 1903
10 132 236 366 529 720 940 1189 1463 1780 2114
12 157 282 440 634 864 1128 1428 1762 2133 2537
14 185 329 514 740 1008 1316 1666 2056 2490 2960
16 211 376 587 846 1152 1504 1904 2350 2844 3383
18 238 423 660 952 1296 1692 2140 2640 3200 3806
20 264 470 734 1057 1440 1880 2380 2932 3556 4230

CAPACITY OF RECTANGULAR TANKS

To find the capacity in U.S. gallons of rectangular tanks, reduce all

dimensions to inches, then multiply the length by the width by the height
and divide the product by 231.
Example: Tank 56” long x 32” wide x 20” deep
Then 56” x 32” x 20” = 35,840 cu. in.
35,840 ÷ 231 = 155 gallon capacity

94
 CHAPTER 14 - MISCELLANEA

GRAINS OF MOISTURE PER CUBIC FOOT OF AIR AT

VARIOUS TEMPERATURES AND HUMIDITIES

Temp. Relative Humidity, Percent

°F. 100% 90% 80% 70% 60% 50% 40% 30% 20% 10%
75 9.35 8.42 7.49 6.55 5.61 4.68 3.74 2.81 1.87 0.94
72 8.51 7.66 6.81 5.96 5.11 4.25 3.40 2.55 1.70 0.85
70 7.98 7.18 6.38 5.59 4.79 3.99 3.19 2.39 1.60 0.80
67 7.24 6.52 5.79 5.07 4.35 3.62 2.90 2.17 1.45 0.72
65 6.78 6.10 5.43 4.75 4.07 3.39 2.71 2.04 1.36 0.68
60 5.74 5.17 4.60 4.02 3.45 2.87 2.30 1.72 1.15 0.57
50 4.08 3.67 3.26 2.85 2.45 2.04 1.63 1.22 0.82 0.41
40 2.85 2.56 2.28 1.99 1.71 1.42 1.14 0.86 0.57 0.29
30 1.94 1.74 1.55 1.35 1.16 0.97 0.78 0.58 0.39 0.19
20 1.23 1.11 0.99 0.86 0.74 0.62 0.49 0.37 0.25 0.12
10 0.78 0.70 0.62 0.54 0.47 0.39 0.31 0.23 0.16 0.08
0 0.48 0.43 0.39 0.34 0.29 0.24 0.19 0.14 0.10 0.05

7000 Grains of moisture = 1 pound of water

HEATING CONVERSION FACTORS

BTUs X 1054.8 = Joules

BTUs X 0.2520 = Kg. Cal.

Calories X 4.186 = Joules

Joules X 0.23889 = Calories

Joules X .0002389 = Kg. Cal.

Kg. Cal. X 3.9685 = BTUs

KW-hr X 860.01 = Kg. Cal.

KW-hr X 3413.0 = BTUs

Watt-hr X 3.413 = BTUs

95
 CHAPTER 14 - MISCELLANEA

QUANTITY OF HEAT IN BTU REQUIRED TO RAISE 1 CU. FT.

OF AIR THROUGH A GIVEN TEMPERATURE INTERVAL

External Temperature of Air in Room

Temp.
Degrees F 40 50 60 70 80 90 100 110
-40 1.802 2.027 2.252 2.479 2.703 2.928 3.154 3.379
-30 1.540 1.760 1.980 2.200 2.420 2.640 2.860 3.080
-20 1.290 1.505 1.720 1.935 2.150 2.365 2.580 2.795
-10 1.051 1.262 1.473 1.684 1.892 2.102 2.311 2.522
0 0.822 1.028 1.234 1.439 1.645 1.851 2.056 2.262
10 0.604 0.805 1.007 1.208 1.409 1.611 1.812 2.013
20 0.393 0.590 0.787 0.984 1.181 1.378 1.575 1.771
30 0.192 0.385 0.578 0.770 0.963 1.155 1.345 1.540
40 — 0.188 0.376 0.564 0.752 0.940 1.128 1.316
50 — — 0.184 0.367 0.551 0.735 0.918 1.102
60 — — — 0.179 0.359 0.538 0.718 0.897
70 — — — — 0.175 0.350 0.525 0.700

MELTING POINTS OF METALS

Degrees F. Degrees F.
Aluminum 1220 Iron (Cast) Gray 2460-2550
Antimony 1167 Iron (Cast) White 1920-2010
Bismuth 520 Iron, Wrought 2460-2640
Brass (Red) 1870 Lead 622
Bronze 1900 Silver (Pure) 1761
Copper 1981 Steel 2370-2550
Glass 2377 Tin 449
Gold (Pure) 1945 Zinc 787
Solder (Lead-Tin) 250-570

96
 CHAPTER 14 - MISCELLANEA

CONVERSION FACTORS

WATER
U.S. Gallons x 8.34 = Pounds
U.S. Gallons x 0.13368 = Cubic Feet
U.S. Gallons x 231.00 = Cubic Inches
U.S. Gallons x 3.78 = Liters
Imperial Gallons x 277.3 Cubic Inches
Imperial Gallons at 62°F = 10.0 Pounds
Cubic In. of Water (39.2°) x 0.036130 = Pounds
Cubic In. of Water (39.2°) x 0.004329 = U.S. Gallons
Cubic In. of Water (39.2°) x 0.576384 = Ounces
Cubic Feet of Water (39.2°) x 62.427 = Pounds
Cubic Feet of Water (39.2°) x 7.48 = U.S. Gallons
Cubic Feet of Water (39.2°) x 0.028 = Tons
Pounds of Water x 27.72 = Cubic Inches
Pounds of Water x 0.01602 = Cubic Feet
Pounds of Water x 0.12 = U.S. Gallons

PRESSURE
1 Pound Per Square Inch = 144 Pounds Per Square Foot
2.0355 Inches of Mercury at 32°F.
2.0416 Inches of Mercury at 62°F.
2.309 Feet of Water at 62°F.
27.71 Inches of Water at 62°F
6.895 kPA (kilopascal)
1 Ounce Per Square Inch = 0.1276 Inches of Mercury at 62°F.
1.732 Inches of Water at 62°F.
1 Atmosphere = 2116.3 Pounds Per Square Foot
(14.7 Lbs. Per Sq. In.) 33.947 Feet of Water at 62°F.
30 Inches of Mercury at 62°F.
29.922 Inches of Mercury at 32°F.
760 Millimeters of Mercury at 32°F.
101.3 kilopascal
1 Inch Water = 0.03609 Lbs. or 0.5774 oz Per Sq. In.
(at 62°F.) 5.196 Pounds Per Square Foot
0.248 kilopascal
1 Foot Water = 0.433 Pounds Per Square Inch
(at 62°F.) 62.355 Pounds Per Square Foot
1 Inch Mercury = 0.491 Lbs. or 7.86 oz. Per Sq. In
(at 62°F.) 1.132 Feet Water at 62°F.
13.58 Inches Water at 62°F.
97
 CHAPTER 14 - MISCELLANEA

EQUIVALENT VALUE IN DIFFERENT UNITS

1 H.P. = 746 watts
.746 K.W.
33,000 ft.-lbs. per minute
550 ft.-lbs. per second
2.64 lbs water evaporated per hour from and at
212°F.
1 H.P. Hour = 746 K.W. hours
2.64 lbs water evaporated per hour from and at
212°F.
17.0 lbs. water raised from 62° to 212°F.
1 Kilowatt = 1,000 watts
1.34 H.P.
3.53 lbs. water evaporated per hour from and at
212°F.
1 Watt = .00134 H.P.
.0035 lb. water evaporated per hour
1 K.W. Hour = 1,000 watt hours
1.34 H.P. Hours
3,600,000 joules
3.53 lbs. water evaporated from and at 212°F.
22.75 lbs. of water raised from 62°F to 212°F
1 Joule = 1 watt second
.000000278 K.W. hour
MJ = Megajoule = 1,000,000 Joule = 948 BTU
239 Kcal

EQUIVALENTS OF ELECTRICAL UNITS

1 Kilowatt = 1.34 H.P.
0.955 BTU per second
57.3 BTU per minute
3438 BTU per hour
1 Horse Power = 746 watts
42.746 BTU per minute
2564.76 BTU per hour
1 BTU = 17.452 watt minutes
0.2909 watt hour

98
 CHAPTER 14 - MISCELLANEA

STANDARD SYMBOLS IN HEATING SPECIFICATIONS

D(delta) = differential, difference in, change in, increment

DP = pressure drop, differential, or loss usually in psi
DT = difference, change or drop in temperature
p (pi) = 3.141592654 = ratio of circumference of a circle
to the diameter of that circle
S (sigma) = sum, summation, total of
W(omega) = ohm, unit of electric resistance = 1 V/A
± = plus or minus, tolerance
¹ = not equal to
< = (is) less than
£ = smaller than or equal to
> = (is) greater than
³ = greater than or equal to
<< = much smaller than
>> = much larger than
T = proportional to, similar to
» = approximately equal to
@ = congruent to
\ = therefore
= angle
= parrallel to
^ = perpendicular to, at right angles to
¥ = infinity, infinite

99
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

Series 2 Gas Boiler

• Cast Iron Package
• Hot Water
• DOE Capacities 31 to 244
MBH
The Series 2 hot water boiler com-
bines the dependability of the a con-
ventional proven atmospheric draft
design with the economy of gas heat.
It is completely factory assembled and
fire tested and requires only minimal
hookup to put into operation. At the
heart of every Series 2 is a durable cast
iron heat exchanger that enhances
energy efficiency and improves boiler
performance and has an added bonus in
the Lifetime True Blue Limited Warranty. Also, the sections are joined
by push nipples that can expand and contract with the sections they join.
The Series 2 is equipped with a fuel saving vent damper and achieves annual
fuel utilization efficiencies up to 84% (Model 2h). Combined, the Series
2 is your long term investment in quality, dependable home heating.
Certified for installation on combustible flooring. Do not install on
carpeting.
Series 2PV Gas Boiler
• Induced Draft
• Cast Iron Package
• Hot Water
• DOE Capacities 51 to 135 MBH
The Series 2PV induced draft boiler
is designed for new or replacement in-
stallations and electric heat conversions
where a chimney is deteriorated or not
available. It can be installed almost
anywhere, such as a closet, utility room
or garage. Available power vented di-
rectly through the wall. A cast iron heat
exchanger, together with a draft induc-
ing fan, provide for more heat with less
fuel and eliminate heat loss through the
vent. No vent damper is required. Burnham also backs the heat exchanger on
the Series 2PV with their Lifetime True-Blue Limted Warranty.

100
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

Spirit® Gas Boiler

• Direct Vent
• Cast Iron Package
• Hot Water
• DOE Capacities 62 to 164 MBH
The Spirit direct vent gas boiler is
designed for new or replacement instal-
lations and electric heat conversions
where a chimney is not available. It can
be installed almost anwhere, such as in
a closet, utility room or garage. Its sealed
combustion, direct vent design helps
regulate combustion air to help avoid
operational and safety problems. A cast
iron heat exchanger, together with a
draft inducing fan, provide for more
heat with less fuel and eliminate heat loss through the vent. No vent damper
is required. Certified for installation on combustible flooring. Do not install
on carpeting.

Independence®/Independence PV
Gas Boiler
• Cast Iron Package, Semi-Pak
or Knockdown
• Steam or Hot Water
• DOE Capacities:
Independence 51 to 317 MBH
Independence PV 52 to 145 MBH
• Natural Draft or Power Vent
Models Available
The Independence and Indep-
endence PV gas-fired steam or hot
water boilers offer the dependability
and quality of cast iron construction.
The Independence can be used for
natural gas or LP gas (IN3-IN9).
Burnham also offers the Independence as a power vented boiler for situations
where a chimney doesn't exist or or if an old chimney is deteriorated.
The Independence PV (steam only) induced draft boiler installs almost
anywhere because no chimney is required for installation. Certified for
installation on combustible flooring. Do not install on carpeting.
101
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

Revolution™ Gas Boiler

• Direct Vent
• Cast Iron Package
• Hot Water
• 87% AFUE
• DOE Capacities 55 to 160
MBH
As Burnham's most effi-
cient gas-fired boiler, the
Revolution is unmatched in
versatility. Available in five
sizes, the Revolution is easily
combined with an indirect wa-
ter heater and zoning controls
for total home comfort. And because of the variety of venting options, the
Revolution is adaptable to the floorplan of virtually any home. Consider
these features:
• Familiar and proven gas train and controls.
• No additional piping or accessories to run directly on radiant systems.
• Supply temperatures anywhere from 60 to 200 without worry of damage from
condensation.
• A built-in injection pump to provide precise temperature control.
• A built-in primary/secondary loop to save time and simplify installation.
• All connections from top to allow for minimal clearances.

Minuteman® II Combination
Boiler/Water
Heater
• Cast Iron Construction
• Natural or LP Gas
• AFUE up to 83%
• Sealed Combustion
• 4 Sizes up to 140 MBH Input
• DOE Capacities 58-112 MBH
The Burnham Minuteman II pro-
vides heat and hot water "all in one."
Because of its small footprint, it can
be easily installed in confined areas or
closets. The Minuteman II is ideal for
all heating applications ranging from
single homes, multi-family units, to industrial or commercial applications.
No chimney is necessary, which makes it the most versatile heating
appliance for home comfort today.
102
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

Series 5B Gas Boiler

• Cast Iron Knockdown
Unit
• Steam or Hot Water
• Capacities 320 to 1,560
MBH
The Series 5B boiler offers
the capacities and features that
make it ideal for commercial,
institutional and high rise resi-
dential heating applications.
The rear outlet drafthood is spe-
cifically suited to installations
involving low ceiling heights.
The Burnham 5B is rated at 50 psi water or 15 psi steam. It has an 80%
combustion efficiency. Plus, only Burnham boilers come with the exclusive
Iron Nipple Seal of Dependability certifying the use of cast iron nipples which
expand and contract with the sections to insure superior quality and reliable
performance. Do not install on combustible flooring.

Series 8B Gas Boiler

• Cast Iron Packaged or
Knockdown Unit
• Hot Water
• Capacities 212 to 475 MBH
The Burnham Series 8B gas
boiler has a vertical flue design
which provides for maximum
heat transfer. Cast iron push
nipples assure the integrity of
the cast iron section assembly
by expanding & contracting at
the same rate and providing a
water tight seal. The Series 8B
boilers can be installed 1" apart (subject to local codes) making them ideally
suited for multiple boiler applications. Do not install on combustible flooring.
A heat shield is required and available for combustible floor installations. Do
not install on carpeting, even with a heat shield.
103
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

Series 8B Modular/Multiple System

• Primary-Secondary
Piping
• Capacities starting at 424
MBH
The Burnham modular/
multiple boiler system puts the
efficiency, cost, and service
advantages of compact gas
boilers to work in space heating
applications where a single
commercial boiler would not
be practical for reasons of
budget or accessibility. The
Series 8B boilers can be installed 1" apart (subject to local codes), making
them ideally suited for modular applications. And the modular/multiple
system utilizes primary-secondary piping to maximize energy efficiency.

Modular/Multiple Control
Packages
• Microprocessor-based
• User-programmable,
User-friendly
Burnham offers ten control
packages for operating modu-
lar/multiple boiler systems.
Control Package A and Penn
Johnson A350 maintain a con-
stant supply water temperature.
Control Package B and Penn
Johnson A350RN are the sim-
plest system for step firing mod-
ules according to outdoor air temperature. Control packages D and E monitor
supply water temperature and outdoor air temperature to step fire boiler
modules for maximum fuel economy. Each has different levels of sophistica-
tion and added features. The Burnham microprocessor-based TMC panel
senses supply water, return water, and outdoor air temperatures to automati-
cally monitor and control the operation of up to eight boiler modules. The
TMC Panel provides boiler status lights and digitally displays supply water,
return water and outdoor air temperatures along with accumulated operating
hours of each boiler. There are a number of programmable variables to allow
accurate set-up for each installation, making the TMC Panel one of the most
sophisticated controllers available. The tekmar 251, 252, 254 and 258 control
offerings are also available.
104
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

V7 Series Oil Boiler

• Cast Iron Package or Knockdown
• Hot Water or Steam
• DOE Capacities 68 to 299 MBH
The fully factory-packaged
Burnham V7 is available for steam or
hot water with heating capacities rang-
ing from 73 to 275 MBH. A knock-
down model is available, as a water or
steam unit, when access to the base-
ment is confined.
The pinned heating surfaces of the
V7's cast iron section assembly, to-
gether with a vertical flue design,
extract maximum heat while main-
taining low draft losses. This results in
higher energy efficiencies and lower
fuel costs. Cleaning can be easily accomplished from the top or side.

LE Series Oil Boiler/Natural

Draft or Direct Vent
• Oil Fired
• Steel Package
• Hot Water
• DOE Capacities 74 to 143
MBH
• AFUEs up to 86.7%
• LE Home Comfort System
includes Energy Control
5000 Microprocessor and
Alliance indirect water
heater
The Burnham LE boiler is the
heart of the LE Home Comfort
System, which includes the Energy Control 5000 and Alliance indirect water
heater. The LE boiler allows quick, low energy start ups because it holds less
water in the boiler vessel. A reversible cast iron swing door gives easy access
to the combustion chamber for easy cleaning.
105
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

RSA Series Oil Boiler

• Steel Package
• Hot Water
• Capacities: 100 to 318 MBH

The RSA Series comes completely

packaged, wired, and assembled for
quick connection to water, fuel, and
electrical service. The RSA comes
equipped with split controls — a light
sensing primary control and an
operating/high limit control.
The high efficiency RSA has a
large combusion area which promotes
heating efficiency while maintaining
low base temperatures. The RSA also
features a new shell design for maximum heat transfer, and spiral turbulators
which reduce stack temperatures while providing further heat transfer. A
heat sheild is required and available for combustible floor installations. Do
not install on carpeting even with a heat shield.

Woodlander Solid Fuel Boiler

• Steel Knockdown Unit
• Two Models Available
The Burnham Woodlander line of
solid fuel units gives you a variety of
heating options. The Woodlander add-
on boiler is furnished complete with all
controls necessary for integration with
your present boiler. It fires either sea-
soned hardwood, anthracite or bitumi-
nous coal.
If you are replacing your entire heat-
ing unit, Burnham has the Woodlander-3,
named for its three fuel flexibility. It has
a high efficiency oil burning section in
addition to the wood or coal burning unit.
Do not install on combustible flooring.

106
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

FD Series Oil, Gas, or

Combination
Fuel Boiler
• Steel Package
• Hot Water
• Vertical or Optional
Horizontal Design
• Capacities 250 to 1,600 MBH
The FD Series boiler is designed for
forced draft firing. The rectangular
shape of the FD provides a smaller
footprint which can fit in areas where
a sectional boiler will not.
The FD Series is ideal as an indirect
hot water supply boiler for spas, car
washes, laundries, commercial swimming pools and restaurants. It can also
supply domestic hot water requirements for hotels, motels or apartments
along with meeting their heating needs. Do not install on combustible
flooring.

V9 Series Oil, Gas,or Combination

Fuel Boiler
• Cast Iron Packaged or
Knockdown Unit
• Hot Water or Steam
• Capacities 346 to 1,899 MBH
Versatile enough to meet plan and
spec job requirements, the new
Burnham V9 boiler is ideal for use in
light commercial installations. Ap-
plicable to both new construction and
replacement jobs, the V9 provides the
longevity of a cast iron boiler as-
sembled with the time-proven integ-
rity of cast iron nipples. The sectional
design of the V9 makes for easy ma-
neuvering and installation in existing
boiler rooms. The sections and individual components fit through standard
doorways and are assembled on-site with a simple ratchet, wrench, and short
draw rods. Packaged and fire-tested units are also available. And the V9
can be installed in a confined area, requiring only nine inches from a right
side wall and 6 1/2 feet of vertical clearance.
107
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

V11 Series Oil, Gas, Combination

Fuel Boiler
• Cast Iron Packaged or
Knockdown Unit
• Steam or Hot Water
• Capacities 667 to 4,551
MBH
Cast iron construction,
sectional design, top or rear
flue outlets, and a variety of
options make the V11 com-
mercial boiler the complete
heating package for engineers
and contractors. Applicable to both new construction and replacement
jobs, the V11 provides the longevity of a cast iron boiler assembled with
the time-proven integrity of cast iron nipples. The sections and individual
components fit through a standard doorway and are assembled on-site with
a simple ratchet, wrench, and short draw rods. Packaged and fire-tested
units are also available. Apartment buildings, schools, hospitals, and
churches to name a few, can all benefit from the V11.

Baseray®
• The Original Cast Iron
Baseboard
Baseray is the original cast
iron radiant baseboard. It is
designed to be inconspicuous
but effective. In fact, Baseray's
design enables heat to be dis-
bursed in both horizontal and
vertical directions. And its cast
iron construction provides ra-
diant heat, lifetime durability,
and dependability.
Baseray assembles up to
and including 6 lineal feet are
shipped in one piece. Longer
assemblies are shipped in two or more pieces or sub-assemblies of 6 feet or
less for assembly on the job.
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

Radiators
• Cast Iron
• Slenderized in 4 thru 48
sections
• Radiant in 4 thru 44
sections
Burnham's line of cast iron ra-
diators is suitable for both resi-
dential and commercial appli-
cations. Both the slenderized
and the radiant models supply a
continuous flow of radiant heat
combined with convection heat.

Duo-Rad®
• Fan Coil Units
• Heating and Cooling
• 10,000 to 22,000 BTU/HR
The Duo-Rad fan coil unit com-
bines luxurious hydronic heat-
ing with cooling in one smartly
styled heat distributor. Duo-
Rads are ideal for both residen-
tial and commercial applica-
tions. They are constructed of
rigid welded steel.
 CHAPTER 15 - BURNHAM PRODUCT REVIEW

Alliance Indirect-Fired Water

Heater
• 4 Sizes - 26, 40, 53, and 79
Gal.
• Commercial Capabilities
• Rapid Recovery
• Stainless Steel Tank and Coil
• Minimal Standby Losses
The Alliance indirect-fired water
heater provides more hot water than
tankless coils and low BTU capacity
direct-fired water heaters can supply.
Available in 4 sizes, it provides abun-
dant hot water at a minimal cost.

Energy Control 5000

• Multiple Zone Heating
Co nt r o l
• Water Heater Control
The Energy Control 5000
microprocessor continually
monitors outdoor air tempera-
ture, indoor supply water tem-
perature, and indoor room air
temperature, maintaing the
lowest water temperature nec-
essary for comfort and boiler
efficiency. The EC5000 pro-
vides control for four zones,
with add-on modules available for additonal requirements.
The EC5000 also utilizes post purge, night setback, and warm weather
shut down. Finally, the EC5000 helps protect your heating system by
blending hot boiler water with cooler water to avoid thermal shock, and
by periodically exercising pumps during the off season to keep them
lubricated.
 VENTING GUIDE FOR BURNHAM GAS BOILERS

• Vent system sizing and installation must be in accordance with National Fuel Gas
Code (ANSI Z223.1-NFPA 54), Part 7, Venting of Equipment, or applicable
provisions of local building codes.
a. Masonry chimney construction must be in accordance with Standard for
Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances (ANSI/
NFPA 211), which includes fire clay flue lining (ASTM C 315, Specifications
for Clay Flue Linings) or listed chimney liner system.
b. An indoor chimney has no outdoor exposure below the roof line. An outdoor
chimney has one or more surfaces exposed to the outdoors below the roof line.
A Type B vent or listed chimney lining system passing through an unused
masonry chimney is considered to be an indoor chimney.
• Burnham will not authorize removal of the automatic vent damper on a boiler
certified. "For use only with automatic vent damper device..." as stated on or near
rating plate.
• Statements apply to Burnham boilers installed in the United States. A revised
or separate Canadian Policy Statement will be issued at a later date.
 BENEFITS OF
BURNHAM'S HOME HEATING
TEAM MEMBERSHIP
Burnham’s Home Heating Team is a 2) Burnham Trade Talk videos -
unique contractor program featuring designed to assist team members in
unequalled benefits to members in selling, applying and servicing
promoting, selling, installing and Burnham products.
servicing Burnham products. 3) Training seminars - features two
As a member of the Home Heating formats: a classic, full-day seminar
Team Burnham will: that effectively educates your staff
on steam, hot water, and modular
SUPPORT YOUR BUSINESS boiler applications. Or participate
1) Safest, most efficient, and most in "mini" seminars, covering special-
dependable products in the industry. ized topics like proper boiler venting,
2) Toll-free telephone number for radiant panel systems, upgrading older
technical as well as sales and systems, electric heat conversions, as
marketing assistance. well as selling Burnham products to
consumers.
3) Team marketing manual to help
you identify more prospects and to REWARD YOUR COMPANY
help increase your closure rate.
Burnham will provide substantial
4) Experienced and competent sales financial rewards to the team
force to give personal assistance in members such as:
service and marketing.
5) Home Comfort Financing sup- 1) Winter Warmth Assurance -
ports you with the easiest to offer and lets you offer the most flexible 5 or
most effective consumer financing 10-year extended parts and labor
programs in the industry. warranty in the industry. Burnham's
WWA can be used as an add-on sale or
HELP YOU PROMOTE can be included in the contractor's
YOUR BUSINESS proposal to help close the sale.
1) Co-op advertising - provides 2) Periodic promotions - designed to
personal funding as well as distributor increase your profitability and make
assisted funding to support your pro- selling Burnham easier and more
motional efforts. interesting.
2) Advertising assistance - ad samples 3) Burnham Trade Council - (12)
for newspapers, radio, yellow pages, tradesmen are selected to represent
billboards and direct mail programs as each region of the country and Canada
well as prepared copy for local public on the Trade Council. Burnham is
relations submissions. committed to listen to and react to
3) Tie-ins to regional ad campaigns. the needs and opportunities put forth
Team members will have the oppor- at periodic meetings. Each region has
tunity to join with Burnham in a representative that is representing
regional and local advertising the trade in that area and the member
campaigns. is available to listen to your needs and
desires.
PROVIDE EDUCATION TO
YOUR EMPLOYEES To join the HHT, contact your local
Burnham sales office and ask to have
1) Burnham Reporter magazine - a Burnham representative contact
periodic magazine provides valuable you about membership. The offices
information concerning new prod- are listed in the front of this book.
ucts, programs and membership
activities.
 BURNHAMREGIONALOFFICES

Northeast Region
(CT, ME, MA, NH, RI and VT)
Burnham Sales Corporation
19-27 Mystic Avenue
Somerville, MA 02145
617-625-9735

Metropolitan New York Region

(NY, NJ)
Middle Atlantic
(PA, DC, DE, MD, WV and Eastern OH)
Central and Western Regions
Burnham Corporation
Regional Sales Offices
PO Box 3079
Lancaster, PA 17604
717-481-8400

HOME HEATING TEAM MEMBERS:

Call your special 1-800#

Originally Published 6/93 - Fifth Edition 2/99