Scribd
Upload
270 views

Parsons Table

The document provides plans and instructions for building a Parsons table. It begins with background on the original Parsons table design from the 1930s. It then lists the materials needed and provides a schematic and step-by-step instructions. The instructions guide the builder through cutting the legs and rails, assembling the base, adding the top, and finishing. The plans were originally published in The Woodworker's Journal in 1986.

Uploaded by

- yAy3e -
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
270 views

Parsons Table

The document provides plans and instructions for building a Parsons table. It begins with background on the original Parsons table design from the 1930s. It then lists the materials needed and provides a schematic and step-by-step instructions. The instructions guide the builder through cutting the legs and rails, assembling the base, adding the top, and finishing. The plans were originally published in The Woodworker's Journal in 1986.

Uploaded by

- yAy3e -
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Project 18173EZ:

Parsons Table
The term “Parsons table” refers to the simple, clean, unadorned table design that origi-
nated during the 1930s at the renowned Parsons School of Design in New York City. The
tables, which can be built from various materials and in many sizes, are both versatile
and elegant. Our table, crafted in whit oak and featuring an olive ash burl veneer top, is
very much in the classic Parsons style.

Parsons Table Materials List


Part Description Size No. Req’d
A Leg 1-3/4" x 1-3/4" x 20" 4
B Rail 1-3/4" x 1-3/4" x 32" 2
C Top 3/4" x 20-1/2" x 30-1/4" 1
D Face Veneer as needed 1
E Reverse Veneer as needed 1
F Stretcher 3/4" x 1-3/4" x 20-1/2" 2
G Cleat 1" x 1" x 29-1/2" 2
Parsons Table Complete Schematic
Parsons Table Step-by-Step Instructions
1. Cut the leg (A) and rail (B) stock.
2. Construct a simple tenon cutting jig from particleboard and 1-3/4" square hard-
wood for cutting the rail tenons (see tenon detail. NOTE: Make the jig so the rail
ends just touch the table saw surface when positioned in the jig.
3. Clamp the rails securely to the jig for safety.
4. Set the table saw blade height to be about 1-1/4".
5. Use three sets of cuts to establish the two tenons (see detail).
6. Set the table saw blade at 45 degrees.
7. Crosscut to a depth of 3/8" as shown in the detail.
8. Reset the table saw blade at 90 degrees.
9. Raise the blade to about 1-3/8".
10. Take care to insure that ONLY the waste is removed and crosscut to remove it (see
detail).
11. Miter the leg ends at 45 degrees.
12. Chisel the mortises to accept the rail tenons.
13. Glue and clamp the two leg/rail assemblies.
14. Allow the glue to dry.
15. Choose an attractive face veneer for visual impact, and any veneer for the reverse
side.
16. Lay up the face and reverse veneers (D and E) on both sides of the plywood top
(C). NOTE: If you start with a slightly oversized top and veneers, you can use the
table saw to conveniently trim the laid-up assembly to its final dimensions.
17. Use a 3" wide painter’s trim roller to spread glue to assemble the veneer to the top.
18. Choose the same material from which you made the legs and rails to make the
stretchers.
19. Cut and rabbet the stretchers (F).
20. Glue the stretchers to either side of the top (see stretcher detail).
21. Use the two cleats (G), glue, and countersunk screws to mount the top/stretcher
assembly to the leg/rail assemblies.
22. Final sand with 220-grit sandpaper.
23. Finish with two coats of lacquer.

These plans were originally published in Volume 10, Issue 3 of The Woodworker’s Jour-
nal (May/June 1986, pages 50-51)

You might also like