Chapter 10 Acceptance Testing and Commissioning
Uploaded by
Kurt Van DelinderChapter 10 Acceptance Testing and Commissioning
Uploaded by
Kurt Van DelinderChapter 10: Acceptance Tests and
Commissioning Measurements
Set of 189 slides based on the chapter authored by
J. L. Horton
of the IAEA publication (ISBN 92-0-107304-6):
Review of Radiation Oncology Physics:
A Handbook for Teachers and Students
Objective:
To familiarize the student with the series of tasks and
measurements required to place a radiation therapy machine into
clinical operation.
Slide set prepared in 2006
by G.H. Hartmann (Heidelberg, DKFZ)
Comments to S. Vatnitsky:
[email protected]
Version 2012
IAEA
International Atomic Energy Agency
CHAPTER 10.
10.1
10.2
10.3
10.4
10.5
TABLE OF CONTENTS
Introduction
Measurement Equipment
Acceptance Tests
Commissioning
Time Requirements
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.
10.1 INTRODUCTION
In many areas of radiotherapy, particularly in the more
readily defined physical and technical aspects of a
radiotherapy unit, the term Quality Assurance (QA) is
frequently used to summarize a variety of actions
To place the unit into clinical operation.
To maintain its reliable performance.
Typically, the entire chain of a QA program for a
radiotherapy unit consists of subsequent actions as
shown in the following slide.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.1 Slide 1
10.1 INTRODUCTION
Subsequent QA actions
Purpose
Clinical needs assessment
Basis for specification
Initial specification and purchase
Specification of data in units of measure,
design of a tender
process
Acceptance testing
Compliance with specifications
Commissioning for clinical use,
Establishment of baseline performance
values
(including calibration)
Periodic QA tests
Monitoring the reference performance
values
Additional quality control tests after
Monitoring possibly changed reference
performance values
any significant repair, intervention,
or adjustment
Planned preventive maintenance
Be prepared in case of malfunctions etc.
program
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.1 Slide 2
10.1 INTRODUCTION
Acceptance tests and commissioning constitute a
major part in this QA program for radiotherapy.
This chapter is focusing on the duties of acceptance
testing and commissioning.
Although calibrations of the treatment beams are a part of
the acceptance tests and commissioning, calibration will
not be discussed in this chapter as it is fully covered in
Chapter 9.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.1 Slide 3
10.2 MEASUREMENT EQUIPMENT
Acceptance tests and commissioning can performed only if
adequate measurement equipment is at disposal:
Radiation survey equipment:
Geiger counter.
Large volume ionization chamber survey meter.
Neutron survey meter (if the unit operates above 10 MeV).
Ionometric dosimetry equipment
Other dosimetric detectors (film, diodes)
Phantoms
Radiation field analyzer and water phantom.
Plastic phantoms.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2 Slide 1
10.2 MEASUREMENT EQUIPMENT
10.2.1 Radiation survey equipment
A Geiger-Mueller (GM) counter and a large volume
ionization chamber survey meter are required for radiation
survey for all
treatment rooms.
Typical survey meters
of various shapes and
sizes.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.1 Slide 1
10.2 MEASUREMENT EQUIPMENT
10.2.1 Radiation survey equipment
For facilities with a treatment unit operated above
10 MeV, neutron survey equipment are necessary.
Example of neutron survey
meters:
Bonner spheres
Long counters
BF3 counters
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.1 Slide 2
10.2 MEASUREMENT EQUIPMENT
10.2.1 Radiation survey equipment
However, for neutron measurements specialized skills
and knowledge are required.
Therefore, it may be appropriate to contract neutron
measurements to a medical physics consulting service.
This may be a less expensive option than developing the
skills and knowledge and acquiring the expensive neutron
detection equipment that is typically required only during
the acceptance tests.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.1 Slide 3
10.2 MEASUREMENT EQUIPMENT
10.2.2 Ionometric dosimetry equipment
During acceptance testing
and commissioning of a
radiation treatment unit, a
variety of radiation beam
properties must be
measured.
Good quality ionometric
dosimetry equipment is
essential for this purpose.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.2 Slide 1
10.2 MEASUREMENT EQUIPMENT
10.2.2 Ionometric dosimetry equipment
Main components of ionometric dosimetry equipment are:
Several ionization chambers (of thimble or plane-parallel type)
Versatile electrometer
Cable and connectors fitting to the electrometer and all chambers
Thermometer, barometer (for absolute dose measurements!)
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.2 Slide 2
10.2 MEASUREMENT EQUIPMENT
10.2.2 Ionometric dosimetry equipment
Typical measurements
and/or characteristics
Central axis depth dose curves
Beam profiles
Adequate type of
ionization chamber
Thimble ionization chambers with
volumes on the order of
0.1 - 0.2 cm3
Output factors
Measurements in rapidly
changing gradients
Small volume ionization chambers,
parallel plane chambers
Calibration measurements
Calibrated thimble ionization chamber
with a volume on the order of 0.5 cm3
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.2 Slide 3
10.2 MEASUREMENT EQUIPMENT
10.2.3 Film
Radiographic film has a long history of use for
quality control measurements in radiotherapy physics.
Example:
Congruence of radiation and
light field (as marked by pinholes)
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.3 Slide 1
10.2 MEASUREMENT EQUIPMENT
10.2.3 Film
Important additional equipment required for film
measurements:
Well controlled film developing unit;
Densitometer to evaluate the darkening of the film (= optical
density) and to relate the darkening to the radiation received.
Note: Since the composition of radiographic film is different
from that of water or tissue, the response of films must
always be checked against ionometric measurements
before use.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.3 Slide 2
10.2 MEASUREMENT EQUIPMENT
10.2.3 Film
In the past decade
radiochromic film has been
introduced into radiotherapy
physics practice.
This film type is selfdeveloping, requiring neither
developer nor fixer.
Principle:
Radiochromic film
contains a special dye
that is polymerized and
develops a blue color
upon exposure
to radiation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.3 Slide 3
10.2 MEASUREMENT EQUIPMENT
10.2.3 Film
Radiochromic film may become more widely used for
photon beam dosimetry because of its independence from
film developing units.
(There is a tendency in diagnostics to replace film imaging by digital
imaging systems.)
Important:
Since the absorption peaks occur at wavelengths different
from conventional radiographic film, the adequacy of the
densitometer must be checked before use.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.3 Slide 4
10.2 MEASUREMENT EQUIPMENT
10.2.4 Diodes
Because of their small size silicon diodes are convenient
for measurements in small photon radiation fields.
Example: Measurements in a 11 cm2 field
Ionization chamber
Diode
Note: Response of diodes must always be checked
against ionometric measurements before use.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.4 Slide 1
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Water phantom (or radiation field analyzer)
Water phantom that
scans ionization chambers
or diodes in the radiation
field is almost mandatory
for acceptance testing
and commissioning.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 1
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
This type of water phantom is frequently also referred to as a
radiation field analyzer (RFA) or an isodose plotter.
Although a two dimensional RFA is adequate, a three
dimensional RFA is preferable, as it allows the scanning of the
radiation field in orthogonal directions without changing the
phantom setup.
Scanner of the RFA should be able to scan 50 cm in both
horizontal dimensions and 40 cm in the vertical dimension.
Water tank should be at least 10 cm larger than the scan in
each dimension.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 2
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Practical notes on the use of an RFA:
The RFA should be positioned with the radiation detector
centered on the central axis of the radiation beam.
Traversing mechanism should move the radiation detector
along the principal axes of the radiation beam.
After the gantry has been leveled with the beam directed
vertically downward, leveling of the traversing mechanism can
be accomplished by scanning the radiation detector along the
central axis of the radiation beam indicated by the image of the
cross-hair.
Traversing mechanism should have an accuracy of movement
of 1 mm and a precision of 0.5 mm.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 3
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Set up of RFA
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 4
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Plastic phantoms
For ionometric measurements a polystyrene or water equivalent
plastic phantom is convenient.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 5
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Plastic phantoms for ionization chambers
One block should be drilled to accommodate a Farmer-type ionization
chamber with the center of the hole, 1 cm from one surface.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 6
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Plastic phantoms for ionization chambers
A second block should be machined to place the entrance window of
a parallel plate chamber at the level of one surface of the block. This
arrangement allows measurements with the parallel plate chamber
with no material between the window and the radiation beam.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 7
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Plastic phantoms for ionization chambers
Additional seven blocks of the same material as the rest
of the phantom should be 0.5, 1, 2, 4, 8, 16 and 32 mm
thick.
These seven blocks combined with the 5 cm thick blocks
allow measurement of depth ionization curves in 0.5 mm
increments to any depth from the surface to 40 cm with
the parallel plate chamber and from 1 cm to 40 cm with
the Farmer chamber.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 8
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Note:
In spite of the popularity of plastic phantoms, for
calibration measurements (except for low-energy xrays) their use of is strongly discouraged, as in general
they are responsible for the largest discrepancies in the
determination of absorbed dose for most beam types.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 9
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Plastic phantoms for films
A plastic phantom is also useful for film dosimetry.
It is convenient to design one section of the phantom to
serve as a film cassette. Other phantom sections can be
placed adjacent to the cassette holder to provide full
scattering conditions.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 10
10.2 MEASUREMENT EQUIPMENT
10.2.5 Phantoms
Notes on the use of plastic phantoms for film dosimetry:
Use of ready pack film irradiated parallel to the central axis of
the beam requires that the edge of the film be placed at the
surface of the phantom and that the excess paper be folded
down and secured to the entrance surface of the phantom.
Pinholes should be placed in a corner of the downstream edge
of the paper package so that air can be squeezed out before
placing the ready pack in the phantom. Otherwise air bubbles
will be trapped between the film and the paper. Radiation will
be transmitted un-attenuated through these air bubbles
producing incorrect data.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.2.5 Slide 11
10.3 ACCEPTANCE TESTS
Acceptance Tests of Radiotherapy Equipment: Characteristics
Acceptance tests assure that
Specifications contained in the purchase order are fulfilled.
Environment is free of radiation.
Radiotherapy equipment is free of electrical hazards to staff and
patients.
Tests are performed in the presence of a manufacturers
representative.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3 Slide 1
10.3 ACCEPTANCE TESTS
Characteristics (continued)
Upon satisfactory completion of the acceptance tests, the
physicist signs a document certifying these conditions are
met.
When the physicist accepts the unit, the final payment is
made for the unit, owner-ship of the unit is transferred to
the institution, and the warranty period begins.
These conditions place a heavy responsibility on the
physicist in correct performance of these tests.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3 Slide 2
10.3 ACCEPTANCE TESTS
Acceptance tests may be divided into three groups:
1. Safety checks.
2. Mechanical checks.
3. Dosimetry measurements.
A number of national and international protocols exist to
guide the physicist in the performance of acceptance tests.
Example: Comprehensive QA for Radiation Oncology, AAPM Task Group 40
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3 Slide 3
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks
Safety checks include:
Interlocks.
Warning lights.
Patient monitoring equipment.
Radiation survey.
Collimator and head leakage.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 1
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Interlocks
Interlocks
Initial safety checks should verify that all interlocks are
functioning properly and reliable.
"All interlocks" means the following four types of
interlocks:
Door interlocks.
Radiation beam-off interlocks.
Motion disable interlocks.
Emergency off interlocks.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 2
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Interlocks
1. Door interlocks:
Door interlock prevents irradiation
from occurring when the door to the
treatment room is open.
1. Radiation beam-off
interlocks:
Radiation beam-off interlocks halt
irradiation but they do not halt the
motion of the treatment unit or
patient treatment couch.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 3
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Interlocks
3. Motion-disable interlocks:
Motion-disable interlocks halt motion of the treatment unit and patient
treatment couch but they do not stop machine irradiation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 4
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Interlocks
4. Emergency-off interlocks:
Emergency-off interlocks typically
disable power to the motors that drive
treatment unit and treatment couch
motions and power to some of the
radiation producing elements of the
treatment unit. The idea is to prevent
both collisions between the treatment
unit and personnel, patients or other
equipment and to halt undesirable
irradiation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 5
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Warning lights
Warning lights
After verifying that all
interlocks and emergency
off switches are
operational, all warning
lights should be checked.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 6
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Patient monitoring equipment
Patient monitoring equipment
Next, the proper
functioning of the patient
monitoring audio-video
equipment can be verified.
Audio-video equipment is
often useful for monitoring
equipment or gauges
during the acceptance
testing and commissioning
involving radiation
measurements.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 7
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Radiation survey
Radiation survey
In all areas outside the treatment room a radiation survey
must be performed.
Typical floor plan for an
isocentric high-energy
linac bunker.
X
Green means:
All areas outside the
treatment room must be
"free" of radiation
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 8
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Radiation survey
For cobalt units and linear accelerators operated below
10 MeV a photon survey is required.
For linear accelerators operated above 10 MeV the
physicist must survey for neutrons in addition to photons.
Survey should be conducted using the highest energy
photon beam.
To assure meaningful results the physicist should perform
a preliminary calibration of the highest energy photon
beam before conducting the radiation survey.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 9
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks : Radiation survey
Practical notes on performing a radiation survey:
Fast response of the Geiger counter is advantageous in
performing a quick initial survey to locate areas of
highest radiation leakage through the walls.
After location of these hot-spots the ionization chambertype survey meter may be used to quantify the leakage
values.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 10
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks : Radiation survey
Practical notes on performing a radiation survey:
First area surveyed should be the control console area
where an operator will be located to operate the unit for all
subsequent measurements.
All primary barriers should be surveyed with the largest
field size, with the collimator rotated to 45, and with no
phantom in the beam.
All secondary barriers should be surveyed with the largest
field size with a phantom in the beam.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 11
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Collimator and head leakage
Source on a cobalt-60 unit or the target on a linear
accelerator is surrounded by a shielding.
Most regulations require this shielding to limit the leakage
radiation to a 0.1 % of the useful beam at one meter from
the source.
Adequacy of this shielding must be verified during
acceptance testing.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 12
10.3 ACCEPTANCE TESTS
10.3.1 Safety Checks: Collimator and head leakage
Practical notes on performing a leakage test:
Use of film ionization chamber combination
Leakage test may be accomplished by closing the collimator
jaws and covering the head of the treatment unit with film.
Films should be marked to permit the determination of their
position on the machine after they are exposed and processed.
Exposure must be long enough to yield an optical density of
one on the films.
Any hot spots revealed by the film should be quantified by
using an ionization chamber-style survey meter.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.1 Slide 13
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks
Mechanical checks include:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Collimator axis of rotation.
Photon collimator jaw motion.
Congruence of light and radiation field.
Gantry axis of rotation.
Patient treatment table axis of rotation.
Radiation isocentre.
Optical distance indicator.
Gantry angle indicators.
Collimator field size indicators.
Patient treatment table motions.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 1
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks
The following mechanical test descriptions are structured
such that for each test four characteristics (if appropriate)
are given:
1.
Aim of test.
2.
Method used.
3.
Practical suggestions.
4.
Expected results.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 2
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator axis of rotation
Aim
Photon collimator jaws rotate on a circular bearing
attached to the gantry.
Axis of rotation is an important aspect of any treatment
unit and must be carefully determined.
Central axis of the photon, electron, and light fields should
be aligned with the axis of rotation of this bearing and the
photon collimator jaws should open symmetrically about
this axis.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 3
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator axis of rotation
Method
Collimator rotation axis can
be found with a rigid rod
attached to the collimator.
This rod should terminate in
a sharp point and be long
enough to reach from where
it will be attached to the
approximate position of
isocenter.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 4
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator axis of rotation
Practical suggestions
Gantry should be positioned to point the collimator axis vertically
downward and then the rod is attached to the collimator housing.
Millimeter graph paper is attached to the patient treatment couch and
the treatment couch is raised to contact the point of the rod.
With the rod rigidly mounted, the collimator is rotated through its
range of motion. The point of the rod will trace out an arc as the
collimator is rotated.
Point of the rod is adjusted to be near the center of this arc. This point
should be the collimator axis of rotation.
This process is continued until minimum radius of the arc is obtained.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 5
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator axis of rotation
Expected result
Minimum radius is the precision of the collimator axis of
rotation.
In most cases this arc will reduce to a point but should not
exceed 1 mm in radius in any event.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 6
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Photon collimator jaw motion
Aim
Photon collimator jaws should open symmetrically about
the collimator axis of rotation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 7
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Photon collimator jaw motion
Method
A machinist dial indicator
can be used to verify this.
Indicator is attached to a
point on the collimator
housing that remains
stationary during rotation
of the collimator jaws.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 8
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Photon collimator jaw motion
Practical suggestions
Feeler of the indicator is brought into contact with one set of jaws and
the reading is recorded.
Collimator is then rotated through 180 and again the indicator is
brought into contact with the jaws and the reading is recorded.
Collimator jaw symmetry about the rotation axis is one half of the
difference in the two readings. This value projected to the isocenter
should be less than 1 mm.
This procedure is repeated for the other set of collimator jaws.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 9
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Photon collimator jaw motion
Expected result
This value projected to the isocentre should be less than
1 mm. This procedure is repeated for the other set of
collimator jaws.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 10
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Photon collimator jaw motion
Aim
The two sets of collimator jaws should be perpendicular to
each other.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 11
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Photon collimator jaw motion
Method
To check this, the gantry is rotated to orient the collimator axis
of rotation horizontally.
Then the collimator is rotated to place one set of jaws
horizontally.
A spirit level is placed on the jaws to verify they are horizontal.
Then the spirit level is used to verify that the vertically
positioned jaws are vertical.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 12
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator angle indicator
Method
Accuracy of the collimator angle indicator can be determined
by using a spirit level.
With the jaws in the position of the jaw motion test the
collimator angle indicators are verified. These indicators should
be reading a cardinal angle at this point, either 0, 90, 180, or
270 depending on the collimator position. This test is repeated
with the spirit level at all cardinal angles by rotating the
collimator to verify the collimator angle indicators.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 13
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Congruence of light and radiation field
Aim
Correct alignment of the radiation field is always checked
by the light field. Congruence of light and radiation field
must therefore be verified. Additional tools can be used.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 14
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Congruence of light and radiation field
Method: Adjustment
With millimeter graph paper attached to the patient treatment
couch, the couch is raised to nominal isocentre distance.
Gantry is oriented to point the collimator axis of rotation
vertically downward. The position of the collimator axis of
rotation is indicated on this graph paper.
The projected image of the cross-hair should be coincident with
the collimator axis of rotation and should not deviate more than
1 mm from this point as the collimator is rotated through its full
range of motion.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 15
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Congruence of light and radiation field
Method (continued)
Congruence of the light and radiation field can now be verified. A
radiographic film is placed perpendicularly to the collimator axis
of rotation.
The edges of the light field are marked with radio-opaque objects
or by pricking holes with a pin through the ready pack film in the
corners of the light field.
Plastic slabs are placed on top of the film such, that the film is
positioned near zmax
Film is irradiated to yield an optical density between 1 and 2.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 16
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Congruence of light and radiation field
Expected result
The light field edge should correspond to the radiation field
edge within 2 mm.
Any larger misalignment between the light and radiation field
may indicate that the central axis of the radiation field is not
aligned to the collimator axis of rotation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 17
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry axis of rotation
Aim
As well as the collimator rotation axis, the gantry axis of
rotation is an important aspect of any treatment unit and must
be carefully determined.
Two requirement on the gantry axis of rotation must be fulfilled:
Good stability
Accurate identification of the position (by cross hair image and/or laser
system)
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 18
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry axis of rotation
Method
Gantry axis of rotation can be
found with a rigid rod aligned
along the collimator axis of
rotation; its tip is adjusted at
nominal isocentre distance.
A second rigid rod with a
small diameter tip is attached
at the couch serving to identify
the preliminary isocenter point
.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 19
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry axis of rotation
Practical suggestions
Gantry is positioned to point the central axis of the beam
vertically downward. Then the treatment table with the second
rigid rod is shifted along its longitudinal axis to move the point
of the rod out of contact with the rod affixed to the gantry.
Gantry is rotated 180 and the treatment couch is moved back
to a position where the two rods contact. If the front pointer
correctly indicates the isocentre distance, the points on the two
rods should contact in the same relative position at both angles.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 20
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry axis of rotation
Practical suggestions
If not, the treatment couch height and length of the front pointer
are adjusted until this condition is achieved as closely as
possible.
Because of flexing of the gantry, it may not be possible to
achieve the same position at both gantry angles.
If so, the treatment couch height is positioned to minimize the
overlap at both gantry angles. This overlap is a zone of
uncertainty of the gantry axis of rotation.
This procedure is repeated with the gantry at parallel-opposed
horizontal angles to establish the right/left position of the gantry
axis of rotation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 21
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry axis of rotation
Expected result
The tip of the rod affixed to the treatment table indicates the
position of the gantry axis of rotation.
The zone of uncertainty should not be more than 1 mm in
radius.
The cross-hair image is aligned such that it passes through the
point indicated by the tip of the rod.
Patient positioning lasers are aligned to pass through this point.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 22
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Couch axis of rotation
Aim
Collimator axis of rotation, the gantry axis of rotation, and the
treatment couch axis of rotation ideally should all intersect in a
point.
Note:
Whereas the collimator
and gantry rotation axis
can hardly be changed
by a user, the position
of the couch rotation axis
can indeed be adjusted.
gantry
axis
collimator
axis
treatment couch
axis
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 23
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Couch axis of rotation
Method
Axis of rotation of the patient treatment couch can be found
by observing and noting the movement of the cross-hair
image on a graph paper while the gantry with the collimator
axis of rotation is pointing vertically downward.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 24
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Couch axis of rotation
Expected result
Cross-hair image should trace an arc with a radius of less
than 1 mm.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 25
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Radiation isocenter
Aim
Radiation isocenter is primarily determined by the intersection
of the three rotation axes: the collimator axis of rotation, the
gantry axis of rotation, and the treatment couch axis of rotation.
In practice, they are not all intersecting at a point, but within a
sphere.
Radius of this sphere determines the isocenter uncertainty.
Radiation isocentre should be determined for all photon
energies.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 26
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Radiation isocenter
Method
Location and dimension of
the radiation isocentre
sphere can be determined
by a film using the "starshot" method.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 27
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Radiation isocenter
Practical suggestions
Ready-pack film is taped to one of the plastic blocks that
comprise a plastic phantom.
Film should be perpendicular to and approximately centered on
the gantry axis of rotation.
A pin prick is made in the film to indicate the gantry axis of
rotation.
Then a second block is placed against the film sandwiching it
between the two blocks and the collimator jaws are closed to
approximately 1 mm 1 mm.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 28
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Radiation isocenter
Practical suggestions
Without touching the film, the film is exposed at a number of
different gantry angles in all four quadrants.
In addition, the film can be exposed at a number of different
couch angles.
Processed film should show a multi-armed cross, referred to as
a star shot.
The point where all central axes intersect is the radiation
isocentre.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 29
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Radiation isocenter
Expected result
Because of gantry flex, it may be a few millimeters wide but
should not exceed 4 mm. This point should be within 1 mm to 2
mm of the mechanical isocentre indicated by the pin-prick on
the film.
Collimator axis of rotation, the gantry axis of rotation and the
treatment table axis of rotation should all intersect in a sphere.
The radius of this sphere determines the isocentre uncertainty.
This radius should be no greater than 1 mm, and for machines
used in radiosurgery should not exceed 0.5 mm.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 30
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Optical distance indicator
Method
Convenient method to
verify the accuracy of the
optical distance indicator
over the range of its readout consists of projecting
the indicator on top of a
plastic phantom with
different heights.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 31
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Optical distance indicator
Practical suggestions
With the gantry positioned with the collimator axis of rotation
pointing vertically downward five of the 5 cm thick blocks are
placed on the treatment couch with the top of the top block at
isocentre.
Optical distance indicator should read isocentre distance.
By adding and removing 5 cm blocks the optical distance
indicator can be easily verified at other distances in 5 cm
increments.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 32
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Optical distance indicator
Expected results
Deviation of the actual height from that indicted by the optical
distance indicator must comply with the specification.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 33
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry angle indicators
Method
Accuracy of the gantry
angle indicators can be
determined by using a
spirit level.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 34
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry angle indicators
Practical suggestions
At each of the nominal cardinal angles the spirit level should
indicate correct level.
Some spirit levels also have an indicator for 45 angles that
can be used to check angles of 45, 135, 225, and 315.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 35
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Gantry angle indicators
Expected results
Gantry angle indicators should be accurate to within 0.5.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 36
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator field size indicators
Method
Collimator field size indicators can be checked by comparing
the indicated field sizes to values measured on a piece of
graph paper.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 37
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator field size indicators
Practical suggestions
Graph paper is fixed to the treatment couch with the top of the
couch raised to isocentre height.
Range of field size should be checked for both symmetric and
asymmetric field settings.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 38
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Collimator field size indicators
Expected results
Field size indicators should be accurate to within 2 mm.
(Suggested in: Comprehensive QA for Radiation Oncology, AAPM
Task Group 40)
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 39
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Couch motions
Aim
Patient treatment couch should exactly move in vertical
and horizontal planes.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 40
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Couch motions
Method
The vertical motion can be checked by attaching a piece
of millimeter graph paper to the treatment couch and with
the gantry positioned with the collimator axis of rotation
pointing vertically downward.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 41
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Couch motions
Practical suggestions
Mark the position of the image of the cross-hair on the paper.
As the treatment couch is moved through its vertical range, the
cross-hair image should not deviate from this mark.
Horizontal motions can be checked in a similar fashion with the
gantry positioned with the collimator axis in a horizontal plane.
By rotating the treatment couch 90 degrees from its neutral
position, the longitudinal motion can be verified.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 42
10.3 ACCEPTANCE TESTS
10.3.2 Mechanical Checks: Couch motions
Expected results
Deviation of the movement from vertical and horizontal
planes must comply with the specification.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.2 Slide 43
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements
After completion of the mechanical checks, dosimetry
measurements must be performed.
Dosimetry measurements establish that
Central axis percentage depth doses, and
Off axis characteristics of clinical beams meet the specifications.
Characteristics of the monitor ionization chamber of a linear
accelerator or a timer of a cobalt-60 unit are also determined.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 1
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements
Dosimetry measurements include:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Photon energy.
Photon beam uniformity.
Photon penumbra.
Electron energy.
Electron beam bremsstrahlung contamination.
Electron beam uniformity.
Electron penumbra.
Monitor characteristics.
Arc therapy.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 2
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements
The following dosimetry measurement descriptions are
structured such that for each test two characteristics
are given:
1.
Parameter used to specify the dosimetrical property.
2.
Method used.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 3
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon energy
Specification
Energy specification of an x-ray beam is usually stated in
terms of the central axis percentage depth dose.
Typically used: Central axis percentage depth dose value
in a water phantom for:
100
80
PDD
SSD = 100 cm.
Field = 1010 cm2.
Depth of 10 cm.
60
40
20
0
0
10
15
20
25
depth / cm
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 4
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon energy
Method
During acceptance testing the central axis percentage
depth dose value will be determined with a small volume
ionization chamber in a water phantom according to the
acceptance test protocol.
This value is compared to values given in the British
Journal of Radiology, Supplement 25 to determine a
nominal energy for the photon beam.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 5
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon beam uniformity
Specification
Uniformity of a photon beam can be specified in terms of:
Flatness and symmetry measured in transverse
beam profiles.
or
Uniformity index.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 6
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon beam uniformity
Methods using transverse beam profiles
Beam flatness F
obtained from the
profile in 10 cm depth:
1.1
1.0
Dmin
Dmax
0.9
Dmax Dmin
F 100
Dmax Dmin
relative dose
0.8
central area
=80%
0.7
0.6
0.5
Col 1 vs Col 2
Col 1 vs Col 2
0.4
0.3
field size
0.2
0.1
0.0
-100
-50
50
100
mm
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 7
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon beam uniformity
Methods using transverse beam profiles
Beam symmetry S
110
obtained from the profile
at depth of dose maximum
arealeft +arearight
90
relative dose in %
S 100
arealeft arearight
100
80
70
60
50
40
30
area left
20
area right
10
0
-100
-50
50
100
mm
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 8
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon beam uniformity
Methods using the uniformity index
Uniformity index UI is measured in a plane
perpendicular to the central axis.
area 90%
UI is defined using the areas
enclosed by the 90 % and
50 % isodose by the
relationship:
area 50%
area90%
UI
area50%
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 9
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon penumbra
Specification
Profile at 10 cm depth
1.1
Photon penumbra is
typically defined as the
distance between the
80 % and 20 % dose
points on a transverse
beam profile measured
in water phantom at
depth of 10 cm.
1.0
0.9
0.8
1.1
0.7
1.0
0.6
0.9
0.8
0.5
0.7
0.4
0.6
0.3
0.5
0.2
0.4
0.3
0.1
0.2
0.0
-150
-100
-50
0.1
50
100
150
0.0
mm
-60
-50
-40
mm
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 10
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Photon penumbra
Method
During acceptance testing the profile dose value will be
determined with a small volume ionization chamber in a
water phantom according to the acceptance test protocol.
Whenever penumbra values are quoted, the depth of
profile should be stated.
Note: There are also other definitions of the penumbra,
such as the distance between the 90 % and 10 % dose
points on the beam profile at a given depth in phantom.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 11
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Electron energy
Specification
Electron energy can be specified as the most probable
electron energy Ep,0 at the surface of a water phantom.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 12
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Electron energy
Method
Ep,0 is based on the
measurement of the
practical range Rp in a
water phantom.
Ep,0 is determined from
the practical range with
the following equation:
Ep,0 0.0025Rp2 1.98Rp 0.22
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 13
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Bremsstrahlung contamination
Specification
Bremsstrahlung
contamination of the
electron beam is the
radiation measured
beyond the practical range
of the electrons in percent
of the maximum dose.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 14
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Bremsstrahlung contamination
Method
Bremsstrahlung contamination of the electron beam is
determined directly from PDD curves measured in electron
beams.
For this purpose, the central axis PDD must be measured
to depths large enough to determine this component.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 15
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Electron beam uniformity
Specification
Uniformity of an electron beam can be specified similar to
that of photon beams in terms of the
Flatness and symmetry measured in transverse beam profiles
or
Uniformity index
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 16
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Electron beam uniformity
Note
The IEC definition of
electron field uniformity
includes measuring
beam profiles at depths
of 1 mm, the depth of
the 90 % dose, and at
one half the depth of the
80 % dose.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 17
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Monitor characteristics
Specifications
Monitor unit device consists of
Timer in case of a cobalt unit.
Ionization chamber that intercepts the entire treatment beam in
case of a linear accelerator.
The following characteristics of the monitor unit device
must be checked:
Linearity
Independence from temperature-pressure fluctuations.
Independence from dose rate and gantry angle.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 18
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Monitor characteristics
Methods: Linearity
Linearity of the monitor unit device should be verified by
placing an ionization chamber at a fixed depth in a
phantom and recording the ionization collected during
irradiations with different time or monitor unit settings over
the range of the monitor.
Collected ionization can be plotted on the y-axis and the
monitor or time setting on the x-axis. These data should
produce a straight line indicating a linear response of the
monitor unit device or timer.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 19
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Monitor characteristics
Methods: Linearity
These data should produce a straight line indicating a
Integrated ionization
chamber current
linear response of the monitor unit device or timer.
Monitor or time setting
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 20
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Monitor characteristics
Negative x-intercept:
more radiation is delivered than
indicated by the monitor unit setting.
Positive x-intercept:
less radiation is delivered than indicated
by the monitor unit setting.
This end effect should be determined for each energy and
modality on the treatment unit.
For teletherapy units and orthovoltage x-ray units this
effect is referred to as the shutter correction.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 21
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Monitor characteristics
Methods: Independence from temperature-pressure fluctuations
Most linear accelerator manufacturers design the monitor
chamber to be either sealed so that its calibration is independent
of temperature-pressure fluctuations or the monitor chamber has
a temperature-pressure compensation circuit.
Effectiveness of either method should be evaluated by
determining the long-term stability of the monitor chamber
calibration. This evaluation can be performed during
commissioning by measuring the output each morning in a plastic
phantom in a set up designed to reduce set up variations and
increase precision of the measurement.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 22
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Monitor characteristics
Methods: Independence from dose rate and gantry angle
Linear accelerators usually provide the capability of irradiating
at several different dose rates.
Different dose rates may change the collection efficiency of the
monitor ionization chamber, which would change the calibration
(cGy/MU) of the monitor ionization chamber.
Calibration of the monitor ionization chamber should be
determined at all available dose rates of the treatment unit. The
constancy of output with gantry angle should also be verified.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 23
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Arc therapy
Specification
Rotation in arc therapy or rotational therapy must exactly
terminate when the monitor or time setting and at the
same time the number of degrees for the desired arc is
reached.
Proper function is specified by a difference as small as
possible in monitor units (or time) as well as in degrees
from the setting.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 24
10.3 ACCEPTANCE TESTS
10.3.3 Dosimetry Measurements: Arc therapy
Method
A check is accomplished by setting a number of monitor
units on a linear accelerator or time on a cobalt-60 unit
and a number of degrees for the desired arc.
Termination of radiation and treatment unit motion should
agree with the specification.
This test should be performed for all energies and
modalities of treatment and over the range of arc therapy
geometry for which arc therapy will be used.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.3.3 Slide 25
10.4 COMMISSIONING
Characteristics
Following acceptance, a characterization of the equipment's
performance over the whole range of possible operation
must be undertaken.
This is generally referred to as commissioning.
Another definition is that commissioning is the process of
preparing procedures, protocols, instructions, data, etc. for
clinical service.
Clinical use can only begin when the physicist responsible for
commissioning is satisfied that all aspects have been
completed and that the equipment and any necessary data,
etc., are safe to use on patients.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4 Slide 1
10.4 COMMISSIONING
Commissioning of an external beam therapy device includes a
series of tasks:
1. Acquiring all radiation beam data required for treatment.
2. Organizing this data into a dosimetry data book.
3. Entering this data into a computerized treatment planning
4.
5.
6.
7.
system.
Developing all dosimetry, treatment planning, and treatment
procedures.
Verifying the accuracy of these procedures.
Establishing quality control tests and procedures.
Training all personnel.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4 Slide 2
10.4 COMMISSIONING
The following slides are dealing with commissioning
procedures of the most important first item:
acquiring of all photon and
electron beam data required for
treatment planning
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4 Slide 3
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements
Photon beam data to be acquired include:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Central axis percentage depth doses (PDD).
Output factors.
Blocking tray factors.
Characteristics of multileaf collimators.
Central axis wedge transmission factors.
Dynamic wedge data.
Transverse beam profiles/off-axis energy changes.
Entrance dose and interface dosimetry data.
Virtual source position.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 1
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: PDD
Method
Central axis percentage depth doses are preferable measured
in a water phantom.
For measurements, plane-parallel ionization chambers with
the effective point of measurement placed at nominal depth are
recommended.
Note: Effective point of measurement of a plane-parallel chamber is
on the inner surface of the entrance window, at the centre of the
window for all beam qualities and depths.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 2
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: PDD
Note:
Ionization chambers always provide depth-ionization curves.
Since stopping-power ratios and perturbation effects for photon beams are
almost independent of depth, relative ionization distributions can be
used in a very good approximation as relative distributions of absorbed
dose.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 3
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: PDD
Method (continued)
If a cylindrical ionization
chamber is used instead,
then the effective point
of measurement ( ) of
the chamber must be
taken into account.
real
depth
0.6 rcyl
This may require that the complete depth-ionization
distribution be shifted towards the surface a distance
equal to 0.6 rcyl where rcyl is the cavity radius of the
cylindrical ionization chamber.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 4
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: PDD
Practical suggestions
PDD values should be measured over the range of field sizes
from 44 cm2 to 4040 cm2.
Increments between field sizes should be no greater than 5 cm,
but are typically 2 cm.
Measurements should be made to a depth of 35 cm or 40 cm.
Field sizes smaller than 44 cm2 require special attention.
Detectors of small dimensions are required for these
measurements.
A 0.1 cm3 chamber oriented with central electrode parallel to
the central axis of the beam or a diode may be used in a water
phantom.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 5
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: PDD
Note:
Many photon central axis percentage depth doses reveal
a shift in the depth of maximum dose toward the surface
as the field size increases.
This shift results from an increasing number of secondary
electrons in the beam generated from the increasing
surface area of the collimators as well as flattening filter
viewed by the detector.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 6
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Radiation output specified, for example, in
cGy/MU for a linear accelerator .
cGy/min for a cobalt unit.
depends on collimator opening or field shape:
The larger the field size, the larger the radiation output.
Change in output must be known in particular for
Square fields.
Rectangular fields.
Asymmetric fields (if clinically applied).
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 7
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Radiation output is frequently given as a relative factor,
referred to as:
Machine output factor OF.
Relative dose factor (RDF).
Total scatter factor
OF is defined as:
DP ( zmax , A,SSD, E )
OF RDF
DP ( zmax ,10,SSD, E )
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 8
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Method
Output factors should be measured with an ionization
chamber. Water phantom and plastic phantom are equally
appropriate.
Note: Determination of output factors in the small fields is
not easy. Other detectors than ionization chambers may be appropriate.
Their response must always be checked against ionometric measurements
in larger fields.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 9
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Square fields
Output factors OF are usually presented graphically as a
function of the side length of square fields.
1.2
1.1
OF
1.0
0.9
0.8
0.7
0.6
0.5
0
10
15
20
25
30
35
40
side length of square field / cm
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 10
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Rectangular fields
In a good approximation, the output for rectangular fields is
equal to the output of its equivalent square field.
2ab
aeq
ab
This assumption must be verified by measuring the output for a
number of rectangular fields with high and low aspect ratios.
If the outputs of rectangular fields vary from the output of their
equivalent square field by more than 2 %, it may be necessary
to have a table or graph of output factors for each rectangular
field.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 11
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Rectangular fields (cont.)
This matter can be further complicated as linear accelerators
may exhibit a dependence on jaw orientation.
For example, the output of a rectangular field may depend on
whether the upper or lower jaw forms the long side of the field.
This effect is sometimes referred to as the collimator
exchange effect and should be investigated as part of the
commissioning process.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 12
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Asymmetric fields
Treatment with asymmetric fields requires knowledge of the
change of output factors of these fields.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 13
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Asymmetric fields
Output factors for asymmetric fields can be approximated by:
OFa,y
OFa,y
OFs
y
=
=
=
OAR(zmax,y) =
IAEA
OFs OAR( zmax , y )
output factor with asymmetric collimator opening
output factor with symmetric collimator opening
displacement of the central ray of the asymmetric
field from that of the symmetric field
off axis ratio measured at zmax and y centimeters
from the central axis of the symmetric field
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 14
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Collimator scatter factor
Output factor OF is the product of the collimator scatter
factor CF and the phantom scatter factor SF .
OF
CF
SF
OF
CF
SF
(for details see Chapter 6).
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 15
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Collimator scatter factor
Collimator scatter factor is measured in air with a buildup cap large enough to provide electronic equilibrium.
Use of a build-up cap made of higher density material
(aluminum or copper) may be appropriate.
Alternatively, the collimator scatter factor may be
determined by placing the ionization chamber at an
extended SSD.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 16
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Output factors
Phantom scatter factor
Since output factor OF and collimator scatter factor CF
can be measured, and:
OF CFSF
phantom scatter factor SF may be simply found by
dividing the output factor by the collimator scatter factor.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 17
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Blocking tray factors
Purpose
Shielding blocks are frequently used
to protect normal critical structures
within the irradiated area. These
blocks are supported on a plastic tray
to correctly position them within the
radiation field.
Since this tray attenuates the
radiation beam, the amount of beam
attenuation denoted as blocking tray
factors must be known to calculate
the dose received by the patient.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 18
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Blocking tray factors
Method
Attenuation for solid trays is measured by placing an ionization
chamber on the central axis of the beam at 5 cm depth in
phantom in a 1010 cm2 field.
Ratio of the ionization chamber signal with the tray in the beam
to the signal without the tray is the blocking tray transmission
factor.
Although the tray transmission factor should be measured for
several depths and field sizes this factor usually has only a
weak dependence on these variables and typically one may
use one value for all depths and field sizes.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 19
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Multileaf collimators
Purpose
On most current treatment machines multileaf collimators
(MLC) are finding widespread application for conventional field
shaping as a replacement for shielding blocks.
A series of additional data on MLC fields is required such as:
Central axis percentage depth doses.
Penumbra of the MLC fields.
Output factors.
Leakage through and between the leaves.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 20
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Multileaf collimators
Central axis percentage depth doses values
Should be measured in a water phantom. Typically these
values are not significantly different from fields defined with the
collimator jaws.
Penumbra
Penumbra should be measured for both the leaf ends and
edges.
Generally, the MLC penumbra is within 2 mm of the penumbra
of fields defined with the collimator jaws, with the greatest
difference being for singly focused MLC fields not centered on
the collimator axis of rotation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 21
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Multileaf collimators
Output factor
Output factor for MLC fields is generally given by:
OFMLC
with
CFMLC setting SFirradiated area
CF = collimator scatter factor
SF = phantom scatter factor
This relationship must be verified on each machine.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 22
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Multileaf collimators
Leakage
Leakage through the MLC consists of
Transmission through the leaves
Leakage between the leaves.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 23
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Multileaf collimators
Leakage
Leakage can be determined using film
dosimetry.
Method consists of comparing a film
obtained with totally closed MLC
leaves (and hence must be exposed
with a large number of MU) with that
of an open reference field.
Typical values of MLC leakage
through the leaves are in the range of
3 % to 5 % of the isocentre dose.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 24
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Wedge transmission factors
Specification
Central axis wedge transmission factor is the ratio of the dose
at a specified depth on the central axis of a specified field size
with the wedge in the beam to the dose for the same conditions
without the wedge in the beam.
Frequently, the factor determined for one field size at one
depth is used for all wedged fields and depths.
This simplification must be verified for a number of depths and
field sizes.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 25
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Wedge transmission factors
Co-60 Wedge 45 measured profiles (10x10 cm)
300
d=1.5 cm x-axis
relative dose
250
d=1.5 cm y-axis
200
d= 5cm x-axis
d=5 cm y-axis
150
d=10 cm x-axis
d=10 cm y-axis
100
d=20 cm x-axis
50
d=20 cm y-axis
0
-200
-100
100
200
off-axis distance, mm
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 26
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Wedge transmission factors
Method
Wedge transmission factors WF are measured by placing a
ionization chamber on the central axis with its axis aligned
parallel to the constant thickness of the wedge.
Measurements should be performed with the wedge in its
original position and with a rotation of 180 by:
Rotation of the wedge itself which reveals whether or not the side
rails are symmetrically positioned about the collimator axis of
rotation.
Rotation of the collimator which verifies that the ionization
chamber is positioned on the collimator axis of rotation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 27
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Wedge transmission factors
Note on the result of WF after wedge rotation:
If (WF0 WF180 ) > 5 % for a 60 wedge
or (WF0 WF180 ) > 2 % for a 30 wedge,
then wedge or the ionization chamber is not positioned
correctly and the situation should be corrected.
Otherwise:
IAEA
WF
WF0 WF180
2
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 28
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Dynamic wedges
Dynamic wedges are generated by modulation of the photon
fluence during the delivery of the radiation field.
Clinical implementation of dynamic wedges requires not only
measurement of central axis wedge transmission factors but
additionally measurements of:
Central axis percentage depth doses.
Transverse beam profiles of the dynamic wedges.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 29
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Dynamic wedges
Method
Central axis percentage depth
dose and transverse profiles must
be measured at each point during
the entire irradiation of the
dynamic wedge field.
Dynamic wedge transverse beam
profiles can be measured with a
detector array or an integrating
dosimeter such as radiochromic
film. When a detector array is
used, the sensitivity of each
detector must be determined.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 30
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Dynamic wedges
Note:
Central axis wedge transmission factors for dynamic
wedges may have much larger field size dependence
than physical wedges and the field size dependence for
dynamic wedges may not be asymptotic.
During commissioning, this characteristic should be
carefully investigated on each machine.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 31
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Transverse beam profiles
Purpose
For calculation of 2-D and 3-D dose distributions,
off-axis dose profiles are required in conjunction with central
axis data.
The number of profiles and the depths at which these profiles
are measured will depend on the requirements of the treatment
planning system.
Frequently off-axis data are normalized to the dose on the
central axis at the same depth.
These data are referred to as off-axis ratios (OAR).
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 32
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Transverse beam profiles
Method
A water phantom (or radiation field analyzer) that scans a small
ionization chamber or diode in the radiation field is ideal for the
measurement of such data.
Note: In addition to those transverse beam profiles on which the
beam model is determined, further profiles (including such of wedge
fields) should be measured to verify the accuracy of the treatment
planning system algorithms.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 33
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Transverse beam profiles
10MV, TPS *******, OPEN, 10x10 cm2, d = 200 mm, error bars 1%, 2mm
100
100
80
80
Relative dose, %
Relative dose, %
10MV, TPS ******, OPEN, 10x10 cm2, d = 50 mm, error bars 1%, 2mm
60
40
60
40
20
20
0
-100
-80
-60
-40
-20
20
Off axis, mm
40
60
80
100
-100
-80
-60
-40
-20
TPS
TPS
IAEA
20
40
60
80
Off axis, mm
Phantom
Phantom
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 34
100
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Entrance/interface dose
Purpose
Knowledge of dose values at interfaces is important in a variety of
clinical situations.
Examples:
Entrance dose between the patient surface and zmax,
Interfaces at small air cavities such as the nasopharynx,
At the exit surface of the patient,
At bonetissue interfaces
Interfaces between a metallic prosthesis and tissue.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 35
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Entrance/interface dose
Method
Rapidly changing dose gradients are typical in interface situations.
Under such conditions, a thin window parallel plate chamber is
adequate to perform measurements.
Note: Measurements with a thin window parallel plate chamber may be
difficult to perform in a water phantom because of the need to waterproof
the chamber and to avoid deformation of the window by hydrostatic
pressure.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 36
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Entrance/interface dose
Method (continued)
Interface measurements are typically carried out in a
plastic phantom in a constant SSD geometry.
IC
constant SSD
1. measurement
2. measurement
3. measurement
First measurement is made with no buildup material.
Next depth is measured by moving the appropriate sheet of buildup
material from the bottom to the top of the phantom, etc.
This scheme maintains a constant SSD as buildup material is added.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 37
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Entrance/interface dose
Method (continued)
Interface dosimetry measurements should always be
performed with both polarities on the entrance window of the
ionization chamber.
Large differences in the signal at the interface will be observed
when the polarity is reversed. Measurements farther from the
interface exhibit decreasingly smaller differences than
measurements nearer the interface.
The true value of the measured ionization is the average from
both polarities.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 38
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Virtual source position
Purpose
Inverse square law behavior
is assumed to be exactly
valid for the virtual source
position.
Knowledge of the virtual
source position is required
for treatment at extended
SSD.
IAEA
Da
Db
Db Da fa / fb
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 39
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements: Virtual source position
Method
A common technique is to make in-air ionization
measurements at several distances from the nominal source
position to the chamber.
1
The data are plotted with
the distance to the nominal
source position on the x-axis
and the reciprocal of the
square root of the ionization
M on the y-axis.
Nominal source distance
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 40
10.4 COMMISSIONING
10.4.1 Photon Beam Measurements
Method (continued)
This data should follow a straight line. If not, the radiation
output does not follow inverse square.
If the straight line passes through the origin the virtual and
nominal source positions are the same.
If the straight line has a positive x-intercept, the virtual
source position is downstream from the nominal source
position while a negative x-intercept indicates an
upstream virtual source position.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.1 Slide 41
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements
Commissioning procedures for acquiring electron beam
data are similar (but not identical) to those of photon
beams.
Data to be acquired include:
1.
2.
3.
4.
Central axis percentage depth doses (PDD)
Output factors
Transverse beam profiles
Corrections for extended SSD applications
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 1
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Method
Central axis percentage depth doses are preferable
measured in a water phantom.
For measurements, plane-parallel ionization chambers
with the effective point of measurement placed at nominal
depth are highly recommended.
Note: Effective point of measurement of a plane-parallel chamber is on
the inner surface of the entrance window, at the center of the window
for all beam qualities and depths.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 2
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Note:
Ionization chambers always provide depth-ionization curves.
Depth-ionization curve
of electrons differs from
the depth-dose curve by
water-to-air stopping
power ratio.
100
18 MeV
the
depthdose
curve
PDD
80
60
depthionization
curve
40
20
0
0
10
12
14
16
depth / cm
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 3
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Note (cont.)
Since the stopping-power ratios water to air are indeed
dependent on electron energy and hence on the depth,
relative ionization distributions must be converted to
relative distributions of absorbed dose.
This is achieved by multiplying the ionization current or charge
at each measurement depth by the stopping-power ratio at that
depth.
Appropriate values are given, for example in the IAEA TRS 398
dosimetry protocol.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 4
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Measurement of R50
In modern calibration protocols, the quality of electron beams is
specified by the so-called beam quality index which is the halfvalue depth in water R50 .
This is the depth in water (in g/cm2) at which the absorbed
dose is 50 % of its value at the absorbed-dose maximum,
measured with a constant SSD of 100 cm and a field size at the
phantom surface of at least
10 cm 10 cm for R50 7 g/cm2 (E0 16 MeV)
20 cm 20 cm for R50 > 7 g/cm2 (E0 > 16 MeV).
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 5
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Practical suggestions
For all beam qualities, the preferred
choice of detector for the
measurement of R50 is a planeparallel chamber.
Water phantom is the preferred
choice.
In a vertical beam the direction
of scan should be towards the
surface to reduce the effect of
meniscus formation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 6
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Practical suggestions (continued)
When using an ionization chamber, the measured quantity is the halfvalue of the depth-ionization distribution in water, R50,ion. This is the
depth in water (in g/cm2) at which the ionization current is 50 % of its
maximum value.
The half-value of the depth-dose distribution in water
R50 is obtained using:
R50 = 1.029R50,ion 0.06 g/cm2 (R50,ion 10 g/cm2)
R50 = 1.059R50,ion 0.37 g/cm2 (R50,ion > 10 g/cm2)
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 7
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Use of cylindrical chambers
For electron beam qualities with R50 4 g/cm2 (i.e., for electron
energies larger than 10 MeV) a cylindrical chamber may be used.
In this case, the reference point at the chamber axis must be
positioned half of the inner radius rcyl deeper than the nominal
depth in the phantom.
Nominal
depth
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 8
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Use of plastic phantoms
For beam qualities R50 < 4 g/cm2 (i.e., for electron energies
smaller than 10 MeV) a plastic phantom may be used.
In this case, each measurement depth in plastic must be
scaled using zw = zpl cpl (Note: zpl in g/cm2) to give the
appropriate depth in water.
Plastic phantom
cpl
Solid water (RMI-457)
0.949
PMMA
0.941
White polystyrene
0.922
(Table is from the IAEA TRS 398 dosimetry protocol)
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 9
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Use of plastic phantoms (cont.)
In addition, the dosimeter reading M at each depth must also be
scaled using
M = Mpl hpl
For depths beyond zref,pl it is acceptable to use the value for hpl at zref,pl
derived from the Table below.
At shallower depths, this value should be decreased linearly to a
value of unity at zero depth.
Plastic phantom
hpl
Solid water (RMI-457)
1.008
PMMA
1.009
White polystyrene
1.019
Table from the IAEA TRS 398 dosimetry protocol .
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 10
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Practical suggestion
Electron percentage depth dose should be measured in
field size increments small enough to permit accurate
interpolation to intermediate field sizes.
Central axis percentage depth dose should be measured
to depths large enough to determine the bremsstrahlung
contamination in the beam.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 11
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: PDD
Practical suggestion
Although skin sparing is
much less than for
photon beams, skin
dose remains an
important consideration
in many electron treatments. Surface dose is
best measured with a
thin-window parallelplate ion chamber.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 12
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
Specification and measurement
Radiation output is function of field size.
Example:
9 MeV electrons
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 13
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
Specification and measurement
Radiation output is a function of field size.
Output is measured at the standard SSD with a small volume
ionization chamber at zmax on the central axis of the field.
Output factors are typically defined as the ratios to the 1010
cm2 field at zmax.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 14
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
Radiation output for specific collimation
Three specific types of collimation are used to define an
electron field:
1. Secondary collimators (cones) in combination with the
x-ray jaws.
2. Irregularly shaped lead or low melting point alloy metal cutouts
placed in the secondary collimators.
3. Skin collimation.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 15
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
1. Radiation output for secondary collimators
Cones or electron
collimators are
available in a limited
number of square
fields typically
55 cm2 to
2525 cm2 in 5 cm
increments.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 16
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
1. Radiation output for secondary collimators (cont.)
The purpose of the cone depends on the manufacturer.
Some use cones only to reduce the penumbra, others use
the cone to scatter electrons off the side of the cone to
improve field flatness.
Output for each cone must be determined for all electron
energies. These values are frequently referred to as cone
ratios rather than output factors.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 17
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
1. Radiation output for secondary collimators (cont.)
For rectangular fields formed by placing inserts in cones
the equivalent square can be approximated with a square
root method.
Validity of this method should be checked on each
machine for which the approximation is used.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 18
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
2. Radiation output for metal cutouts
Irregularly shaped
electron fields are
formed by placing
metal cutouts of
lead or low melting
point alloy in the
end of the cone
nearest the patient.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 19
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
2. Radiation output for metal cutouts (cont.)
Output factors for fields defined with these cutouts depend
on the electron energy, the cone and the area of cutout.
Dependence of output should be determined for square
field inserts down to 44 cm2 for all energies and cones
Note: To obtain output factors down to 44 cm2 is again a
challenge of small beam dosimetry.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 20
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
2. Radiation output for small fields (cont.)
Output factor is the ratio of dose at zmax for the small field
to dose at zmax for the 1010 cm2 field.
Since zmax shifts toward the surface for electron fields with
dimensions smaller than the range of the electrons, it must
be determined for each small field size when measuring
output factors.
For ionometric data this requires converting the ionization
to dose at each zmax before determining the output factor,
rather than simply taking the ratio of the ionizations.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 21
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
2. Radiation output for small fields (cont.)
Film is an alternate solution. It can be exposed in a
polystyrene or water equivalent plastic phantom in a
parallel orientation to the central axis of the beam.
One film should be exposed to a 1010 cm2 field.
The other film is exposed to the smaller field.
Films should be scanned to find the central axis zmax for
each field.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 22
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
3. Radiation output for skin collimation
Skin collimation is accomplished by using a special insert
in a larger electron cone. The skin collimation then
collimates this larger field to the treatment area.
Skin collimation is used
To minimize penumbra for very small electron fields,
To protect critical structures near the treatment area,
To restore the penumbra when treatment at extended distance is
required.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 23
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Output factors
3. Radiation output for skin collimation (cont.)
If skin collimation is clinically applied, particular
commissioning tests may be required.
As for any small field, skin collimation may affect the
percent depth dose as well as the penumbra, if the
dimensions of the treatment field are smaller than the
electron range.
In this case, PDD values and output factors must be
measured.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 24
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Transverse beam profiles
Method using a water phantom
Same methods used for the
commissioning of transverse
photon beam profiles are also
applied in electron beams.
A water phantom (or radiation
field analyzer) that scans a
small ionization chamber or
diode in the radiation field is
ideal for the measurement of
such data.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 25
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Transverse beam profiles
Method using film dosimetry
An alternate technique is to measure directly isodose curves
rather than beam profiles
Film is ideal for this technique.
Film is exposed parallel to the central axis of the beam. Optical
isodensity is converted to isodose.
However, the percent depth dose determined with film is
typically 1 mm shallower than ionometric determination for
depths greater than 10 mm, and for depths shallower than 10
mm the differences may be as great as 5 mm.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 26
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Extended SSD applications
Virtual source position
Frequently electron fields must be treated at extended
distances because the surface of the patient prevents
positioning the electron applicator at the normal treatment
distance.
In this case, additional scattering in the extended air path
increases the penumbral width and decreases the output.
Knowledge of the virtual electron source is therefore required
to predict these changes.
Determination of the virtual source position is similar to the
verification of inverse square law for photons.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 27
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Extended SSD applications
Air gap correction factor
Radiation output as predicted by the treatment planning
computers use the virtual source position to calculate the
divergence of the electron beams at extended SSDs.
In addition to the inverse square factor, an air gap correction
factor is required to account for the additional scattering in the
extended air path.
Air gap factor must be measured.
Air gap correction factors depend on collimator design, electron
energy, field size and air gap. They are typically less than 2 %.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 28
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Extended SSD applications
PDD changes
There can be significant
changes in the percent
depth dose at extended
SSD if the electron cone
scatters electrons to
improve the field flatness.
For these machines it may
be necessary to measure
isodose curves over a range
of SSDs.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 29
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Extended SSD applications
Penumbra changes
Treatment at extended SSD will also increase the penumbra
width.
At lower energies the width of the penumbra (80 % 20 %)
increases approximately proportionally with air gap.
As electron energy increases the increase in the penumbra
width is less dramatic at depth than for lower energies but at
the surface the increase in penumbra remains approximately
proportional to the air gap.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 30
10.4 COMMISSIONING
10.4.2 Electron Beam Measurements: Extended SSD applications
Penumbra changes
In order to evaluate the algorithms in the treatment
planning system in use, it is recommended to include a
sample of isodose curves measurements at extended
SSDs during commissioning.
Note: Penumbra can be restored when treating at extended
distances by use of skin collimation as discussed before.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.4.2 Slide 31
10.5 TIME REQUIRED FOR COMMISSIONING
Following completion of the acceptance tests, the
completion of all the commissioning tasks,
i.e., the tasks associated with placing a treatment unit
into clinical service, can be estimated to require:
1.5 3 weeks per energy
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.5 Slide 1
10.5 TIME REQUIRED FOR COMMISSIONING
Time required for commisioning will depend on machine
reliability, amount of data measurement, sophistication of
treatments planned and experience of the physicist.
Highly specialized techniques, such as, stereotactic
radiosurgery, intraoperative treatment, intensity
modulated radiotherapy, total skin electron treatment,
etc. have not been discussed and are not included in
these time estimates.
IAEA
Review of Radiation Oncology Physics: A Handbook for Teachers and Students - 10.5 Slide 2
You might also like
- Calibration of Photon and Electron Beams: Ganesan RamanathanNo ratings yetCalibration of Photon and Electron Beams: Ganesan Ramanathan26 pages
- DC Pandey Electricity and Magnetism (Crackjee - Xyz)77% (13)DC Pandey Electricity and Magnetism (Crackjee - Xyz)778 pages
- Chapter 09 Calibration of Radiotherapy Beams PDFNo ratings yetChapter 09 Calibration of Radiotherapy Beams PDF95 pages
- Acceptance Tests and Commissioning MeasurementsNo ratings yetAcceptance Tests and Commissioning Measurements95 pages
- ABR Radiologic Physics Initial Certification Study Guide: Computer-Based ExaminationsNo ratings yetABR Radiologic Physics Initial Certification Study Guide: Computer-Based Examinations4 pages
- Radiation Therapy Dosimetry - A Practical HandbookNo ratings yetRadiation Therapy Dosimetry - A Practical Handbook505 pages
- Get Clinical 3D Dosimetry in Modern Radiation Therapy 1st Edition Ben Mijnheer Free All Chapters100% (4)Get Clinical 3D Dosimetry in Modern Radiation Therapy 1st Edition Ben Mijnheer Free All Chapters62 pages
- AAPM-TG53 (Quality Assurance For Clinical RTP)No ratings yetAAPM-TG53 (Quality Assurance For Clinical RTP)57 pages
- Booklet 1 Methods For in Vivo Dosimetry in External Radiotherapy100% (1)Booklet 1 Methods For in Vivo Dosimetry in External Radiotherapy87 pages
- Control of Secondary and Scattered RadiationNo ratings yetControl of Secondary and Scattered Radiation40 pages
- Use of Image Registration and Fusion Algorithms and Techniques in Radiotherapy - Report of The AAPM Radiation Therapy Committee Task Group No. 132No ratings yetUse of Image Registration and Fusion Algorithms and Techniques in Radiotherapy - Report of The AAPM Radiation Therapy Committee Task Group No. 13235 pages
- Photon Beam Characteristics & Basic Concepts of Treatment Planning - Dr. K J Maria Das PDFNo ratings yetPhoton Beam Characteristics & Basic Concepts of Treatment Planning - Dr. K J Maria Das PDF63 pages
- SRS SRT Dosimetry - Sonja Dieterich PDFNo ratings yetSRS SRT Dosimetry - Sonja Dieterich PDF43 pages
- Quality Use of AI in Medical Imaging-What Do Radiologists Need To Know?No ratings yetQuality Use of AI in Medical Imaging-What Do Radiologists Need To Know?8 pages
- Image Fusion in Preclinical Applications (PDFDrive)No ratings yetImage Fusion in Preclinical Applications (PDFDrive)212 pages
- Calculation of Air-Kerma Strength and Dose Rate Constant For New BEBIG 60co HDR Brachytherapy Source An EGSnrc Monte Carlo Study100% (1)Calculation of Air-Kerma Strength and Dose Rate Constant For New BEBIG 60co HDR Brachytherapy Source An EGSnrc Monte Carlo Study28 pages
- Acceptance Test and Clinical Commissioning of CT SNo ratings yetAcceptance Test and Clinical Commissioning of CT S8 pages
- Full Download Radiation Therapy Dosimetry: A Practical Handbook 1st Edition Arash Darafsheh PDF DOCX100% (16)Full Download Radiation Therapy Dosimetry: A Practical Handbook 1st Edition Arash Darafsheh PDF DOCX55 pages
- Model-Based Dose Calculation Algorithms in BrachytherapyNo ratings yetModel-Based Dose Calculation Algorithms in Brachytherapy110 pages
- Automatic Treatment Planning For VMAT-based TotalNo ratings yetAutomatic Treatment Planning For VMAT-based Total12 pages
- Image Registration, Deformation, and Enhanced Contouring For Radiotherapy With MIM MaestroNo ratings yetImage Registration, Deformation, and Enhanced Contouring For Radiotherapy With MIM Maestro16 pages
- Summary From Tutorial SlicerRT and Dosimetry AnalysisNo ratings yetSummary From Tutorial SlicerRT and Dosimetry Analysis12 pages
- Shielding Requirements in Helical Tomotherapy: Home Search Collections Journals About Contact Us My IopscienceNo ratings yetShielding Requirements in Helical Tomotherapy: Home Search Collections Journals About Contact Us My Iopscience12 pages
- Slide Set of 195 Slides Based On The Chapter Authored by E.B. Podgorsak of The IAEA Publication (ISBN 92-0-107304-6)No ratings yetSlide Set of 195 Slides Based On The Chapter Authored by E.B. Podgorsak of The IAEA Publication (ISBN 92-0-107304-6)195 pages
- WEBB - The Physics of Three-Dimensional Radiation TherapyNo ratings yetWEBB - The Physics of Three-Dimensional Radiation Therapy368 pages
- Acceptance Testing Commissioning QA LinacsNo ratings yetAcceptance Testing Commissioning QA Linacs17 pages
- Radiation Safety of Accelerator Based Radioisotope Production Facilities: Specific Safety GuideFrom EverandRadiation Safety of Accelerator Based Radioisotope Production Facilities: Specific Safety GuideNo ratings yet
- Machine Acceptance and Quality Assurance: Regional (AFRA) Training Course On Small Field DosimetryNo ratings yetMachine Acceptance and Quality Assurance: Regional (AFRA) Training Course On Small Field Dosimetry82 pages
- Absorbed Dose Determination in External Beam Radiotherapy: An International Code of Practice for Dosimetry Based on Standards of Absorbed Dose To WaterFrom EverandAbsorbed Dose Determination in External Beam Radiotherapy: An International Code of Practice for Dosimetry Based on Standards of Absorbed Dose To WaterNo ratings yet
- Guidelines for the Determination of Standardized Semiconductor Radiation Hardness ParametersFrom EverandGuidelines for the Determination of Standardized Semiconductor Radiation Hardness ParametersNo ratings yet
- Chapter 03 Radiation Dosimeters - PDF IkbalNo ratings yetChapter 03 Radiation Dosimeters - PDF Ikbal113 pages
- Jan Lamprecht Hollow Vs Solid SeismologyNo ratings yetJan Lamprecht Hollow Vs Solid Seismology8 pages
- Chapter-4 Mobile Radio Propagation Large-Scale Path Loss100% (2)Chapter-4 Mobile Radio Propagation Large-Scale Path Loss106 pages
- Antennas for All Applications 3rd Edition John D. Kraus - Own the ebook now with all fully detailed contentNo ratings yetAntennas for All Applications 3rd Edition John D. Kraus - Own the ebook now with all fully detailed content48 pages
- Chapter 6 Momentum & Collisions Nice Check It100% (1)Chapter 6 Momentum & Collisions Nice Check It67 pages
- CS340 Machine Learning Information TheoryNo ratings yetCS340 Machine Learning Information Theory22 pages
