Scribd
Upload
570 views

MiniLog2 en

This document describes a data logger device for measuring cathodic protection systems. It can log data from two channels simultaneously, measure microvolts, and interrupt rectifiers synchronized by GPS. It also allows surveying pipelines to locate defects by measuring voltage gradients and currents while recording GPS positions.

Uploaded by

karyantoherlambang
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
570 views

MiniLog2 en

This document describes a data logger device for measuring cathodic protection systems. It can log data from two channels simultaneously, measure microvolts, and interrupt rectifiers synchronized by GPS. It also allows surveying pipelines to locate defects by measuring voltage gradients and currents while recording GPS positions.

Uploaded by

karyantoherlambang
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Measuring Equipment for

Cathodic Protection

Software

www.weilekes.de

WinLog 2.0
GPS Time + Position

DCVG / CIPS Kit

Slave Relay 50 Amps

Coupon Measuring

Fixed Mounting Kit

March / 2012

Data Logger + GPS Interrupter + DCVG / CIPS Survey


2-Channels (DC + AC = 4 values) Built-in AC filters Microvolt 1 000 samp./s 1 300 000 Values
Built-in 15A mechanical or 30A electronic Relay Chargeable Li-Ion 30 days battery life Waterproof IP68

Data Logger
GPS Interrupter + DCVG Survey
General
The new MiniLog2 is a waterproofed
universal measuring instrument
with LCD and keyboard designed
for CP measurement tasks. Used in
data logger mode, the MiniLog2
samples for both channels DC and
AC simultaneously. In interrupter
mode, the built-in relay switches
fully GPS synchro nized for interrupting not only rectifiers, but coupons for IR-free potentials.
Finally with survey mode, the MiniLog2 is able to make
DCVG and CIPS surveys while storing the GPS position for
every measuring point taken.

Data Logger with


Microvolt Measurement
Two channel sampling,
each with DC and AC
measurement, resulting
in 4 values simultaneous
measured per sample.
Both DC channels got
microvolt resolution and
have active filters built-in to
prevent low AC frequency interference. The MiniLog2 is able
to sample up to 1 300 000 values. This results in up to 20 min.
sampling time even when measuring in "high-speed mode"
(= 1000 measurements / second).
The built-in USB connector allows galvanically isolated data
transfer and charging via USB.

GPS Synchronisation
and GPS Position
The optional Garmin GPS
receiver allows synchronisation of the MiniLog2 time
and date. Using the
MiniLog2 as data logger in
DCVG survey mode, the
GPS positions are automatically stored beside
each value.

www.weilekes.de

Miniaturized GPS Interrupter


with Rechargeable Battery
The MiniLog2 has a mechanical
15A / 60V relay built-in for
switching of rectifiers, flanges
and coupons.
Optionally a version with built-in
electronic relay 30A / 60V is
available. Via the keyboard and the LCD a switching
cycle resolution of 0.1s is configurable by the user. In
addition, night and weekend savings are selectable.
The rechargeable Li-Ion battery allows GPS synchronised
switching for 30 days without recharging.
For fixed installations in rectifier housings an USB mains
supply and fix mount can be used.
To increase the switching power even more, miniaturized
external slave relays for MiniLog2 are available with
50 Amps and 100 Amps.
DCVG and CIPS survey with
Google Maps presentation
Like with an analogue multimeter, MiniLog2 shows the
DCVG voltage difference in a
bar graph for quick recognition.
With a simple press of the
OK"-button mounted on the
electrode, the DCVG value and the related GPS position
are stored and the survey continues.
In the same way potential (CIPS) and/or voltage gradient
measurements can be done.
The survey path and the defects can be directly presented graphically with Google Maps and the WinLog 2.0
software.

Coupon Measurement
with MiniCoup
For measuring IR-free potentials on a coupon, MiniLog2
can sample and interrupt
simultaneously. For accurate
sampling of the complete off
depolarisation curve,
MiniLog2 is able to measure
1000 samples/s for one
channel for up to 20 min time.
Optionally with the MiniCoup adapter and its built-in
10 Ohm shunt, the MiniLog2 samples every second for
up to 24h. By just connecting pipe, electrode and coupon
with the adapter sockets, On and Off potential and DC
and AC current are collected simultaneously.

Accessories + Technical Data


MiniLog2

Combined Device and


Accessories Bag

Data Logger, GPS switcher and DCVG


incl. USB cable, 110 / 230 V charger
and 12 / 24 V USB charger

Especially designed
for the MiniLog2 system

Item-No. 130 111 (mechanical relay)


Item-No. 130 121 (electronic relay)

Item-No. 130141

GPS Receiver

GPS Antenna extension

With cable, fitting and


connector for direct mounting

5m, with clip and bush

Item-No. 130131

Item-No. 160191

Metal Carrying Kit

DIN Rail Kit

For DCVG / CIPS survey


with Sprint carrying strap
and OK push-button

For fixed installation


in a rectifier housing

Item-No. 130161

Item-No. 130171

MiniCoup

Powerswitch LS50

Adapter for coupon measurement


(POn + POff + IDC + IAC)

Electronic slave relay


50 Amps / 60 Volt
Mains and Battery operated

Item-No. 130201

Item-No. 140201

Measuring channels :

2 (DC + AC parallel = 4 values)

Power supply:

Measuring range
and resolution:

100 mV /
1 V (only DC)
10 V
/ 0.1 mV (DC + AC)
100 V
/ 10 mV (DC + AC)

Lithium-Ion battery 3.6V / 1900 mAh


Charged with USB power supply

Synchronisation:

GPS and manual or external (Master / Slave)

Input impedance:

10 M (250 K for Microvolt)

Time accuracy:

< 10 ms / 24h with GPS synchronisation

Maximum sampling rate :

1,000 samples / s
10 samples / s (with filter)

Low pass filter :

16,6 Hz > 60 dB (Factor 1,000)


50,0 Hz > 100 dB (Factor 10,000)

Recording capacity :

1,300,000 sampling values


and 10,000 DCVG/CIPS measurements

Switching cycle:

In

0.1s steps, user configurable

Switching power:

Mechanical relay
Electronic relay

External Slave Relay:

LS50
LS100

15A / 60V
30 A / 60V

50A / 60V
100A / 60V

Battery time
Data Logger mode:

10 days with 0.5s sampling rate


20 weeks with 60s sampling rate

Interrupter mode:

30 days with 4/2 and GPS synchronisation

DCVG / CIPS
survey mode:

20 hours with continuous GPS position

Dimension:

148 x 68 x 42 mm

Weight:

350g

Data Logger Software


The software WinLog 2.0 for the evaluation of data
loggings is especially designed for the new MiniLog2.
Beside the easy transfer of the samplings via USB
to the PC, the WinLog 2.0 software supports 4
channel data evaluation with statistic (max, min and
median building) and comprehensive printing features.

For the DCVG and CIPS evaluation WinLog 2.0 with


an internet connection allows the instant presentation of the survey path together with the location of
the defects.
WinLog 2.0 supports the previous MiniLog 128/512
and works with Windows XP, Vista and Windows 7
(32 / 64 Bit)

Stray current sampling during 24h

Median values of the Off-Potential with on screen mouse zoom

Print Coupon switching with 1ms sampling rate

Print: 24h Coupon measurement with POn, POff, IDC and IAC

Built-in export feature for Microsoft Excel

DCVG measurement export to Google Maps for defect localization

Weilekes Elektronik GmbH Am Luftschacht 17 45886 Gelsenkirchen (Germany)


Tel.: +49 (0)209 - 17080-0 Fax: +49 (0)209 - 17080-20 [email protected] www.weilekes.de

You might also like