DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

Description Power Range

Peak Current 60 A (42.4 ARMS)

The DigiFlex® Performance™ (DP) Series digital servo
drives are designed to drive brushed and brushless Continuous Current 30 A (21.2 ARMS)
servomotors. These fully digital drives operate in
torque, velocity, or position mode and employ Space Supply Voltage 100 - 240 VAC
Vector Modulation (SVM), which results in higher bus
voltage utilization and reduced heat dissipation
compared to traditional PWM. The command source
can be generated internally or can be supplied
externally. In addition to motor control, these drives
feature dedicated and programmable digital and
analog inputs and outputs to enhance interfacing with
external controllers and devices.

This DP Series drive features a single RS-232/RS-485

interface used for drive configuration and setup. Drive
commissioning is accomplished using DriveWare,
available at www.a-m-c.com.

All drive and motor parameters are stored in non-

volatile memory.

Features

Four Quadrant Regenerative Operation PIDF Velocity Loop

Space Vector Modulation (SVM) Technology PID + FF Position Loop

Fully Digital State-of-the-art Design Compact Size, High Power Density

Programmable Gain Settings 16-bit Analog to Digital Hardware

Fully Configurable Current, Voltage, Velocity and Built-in brake/shunt regulator

Position Limits Internal brake/shunt resistor

MODES OF OPERATION INPUTS/OUTPUTS

Hall Velocity 3 High Speed Captures
Current 4 Programmable Analog Inputs (16-bit/12-bit
Position Resolution)
Velocity 3 Programmable Digital Inputs (Differential)
COMMAND SOURCE 7 Programmable Digital Inputs (Single-Ended)
Sold & Serviced
PWM and By:
Direction 4 Programmable Digital Outputs (Single-Ended)
Encoder Following COMPLIANCES & AGENCY APPROVALS
Over the Network UL
±10 V Analog cUL
24V Step and Direction CE Class A (LVD)
FEEDBACK SUPPORTED CE Class A (EMC)
Halls RoHS
Toll Free Phone: 877-378-0240
±10 VDC Position
Auxiliary Incremental Encoder
Toll Free Fax: 877-378-0249
1Vp-p Sine/Cosine Encoder
Tachometer (±10 VDC)
[email protected]
www.servo2go.com

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 1 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

BLOCK DIAGRAM

CONTROL MODULE
+5V
3.75K
PDI-1,2,3,4,5,6,7 5k
(STEP / DIR / CAP-A)
HALL A,B,C +
+5V
INPUT COMMON
10k

Feedback
+5V

Feedback
PDI-8,9,10 + (PWM+ / HALL A,B,C –
5k
DIR+ / AUX ENC A,B,I + / Drive 10k
CAP-B,C+) Logic

Motor
+5V COS,SIN,REF MARK +

Motor
PDI-8,9,10 – (PWM– / 10k
DIR– / AUX ENC A,B,I – / COS,SIN,REF MARK –
CAP-B,C–)
10k ENC A,B,I + OUT
OUTPUT PULL-UP
ENC A,B,I – OUT
2.5k

I/O Interface
PDO-1,2,3,4

OUTPUT COMMON
I/O Interface
POWER MODULE
MOTOR A
20k
PAI-1,4 + (REF+) Power Stage MOTOR B
MOTOR C
PAI-1,4 – (REF–)
20k
20k DC+
DC-

PAI-2: 33k Fuse L1

PAI-2,3
PAI-3: 500k Fuse L2
SGN GND Fuse L3

Fuse DC+
Shunt Reg. INT
SELECT 10 (200W)
EXT
TX/TX–
RX/RX– RS232/485 LOGIC+
Interface Logic Power
TX+
LOGIC–
RX+
ISO GND

Information on Approvals and Compliances

US and Canadian safety compliance with UL 508c, the industrial standard for power conversion electronics. UL
registered under file number E140173. Note that machine components compliant with UL are considered UL
registered as opposed to UL listed as would be the case for commercial products.

Compliant with European CE for both the Class A EMC Directive 89/336/EEC on Electromagnetic Compatibility
(specifically EN 61000-6-4:2001, EN 61000-6-2:2001, EN 61000-3-2:2000, and EN 61000-3-3:1995/A1:2001) and
LVD requirements of directive 73/23/EEC (specifically EN 60204-1), a low voltage directive to protect users from
electrical shock.
Sold & Serviced By:
RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being
manufactured in electrical and electronic equipment.

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249
[email protected]
www.servo2go.com

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 2 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

SPECIFICATIONS

Power Specifications
Description Units Value
Rated Voltage VAC (VDC) 240 (339)
AC Supply Voltage Range VAC 100 - 240
AC Supply Minimum VAC 90
AC Supply Maximum VAC 264
AC Input Phases1 - 3
AC Supply Frequency Hz 50 - 60
DC Supply Voltage Range2 VDC 127 - 373
DC Bus Over Voltage Limit VDC 429
DC Bus Under Voltage Limit VDC 55
Logic Supply Voltage VDC 20 - 30 (@ 850 mA maximum)
Maximum Peak Output Current A (Arms) 60 (42.4)
Maximum Continuous Output Current A (Arms) 30 (21.2)
Max. Continuous Output Power @ Rated Voltage3 W 6840
Max. Continuous Power Dissipation @ Rated Voltage W 360
Internal Bus Capacitance µF 1650
External Shunt Resistor Minimum Resistance Ω 10
Minimum Load Inductance (Line-To-Line)4 µH 600
Switching Frequency kHz 20
Maximum Output PWM Duty Cycle % 100
Internal Shunt Fuse Rating A 5 A time-felay fuse
AC Line Fuse Rating A 20 A fast-acting fuses
Low Voltage Supply Outputs - +5 VDC (250 mA)
Control Specifications
Description Units Value
Communication Interfaces - RS-485/232
Command Sources - ±10 V Analog, 24V Step and Direction, Encoder Following, Over the Network, PWM and Direction
±10 VDC Position, 1Vp-p Sine/Cosine Encoder, Auxiliary Incremental Encoder, Halls, Tachometer
Feedback Supported -
(±10 VDC)
Commutation Methods - Sinusoidal
Modes of Operation - Current, Hall Velocity, Position, Velocity
Motors Supported - Closed Loop Vector, Single Phase (Brushed, Voice Coil, Inductive Load), Three Phase (Brushless)
40+ Configurable Functions, Over Current, Over Temperature (Drive & Motor), Over Voltage, Short
Hardware Protection -
Circuit (Phase-Phase & Phase-Ground), Under Voltage
Programmable Digital Inputs/Outputs (PDIs/PDOs) - 10/4
Programmable Analog Inputs/Outputs (PAIs/PAOs) - 4/0
Primary I/O Logic Level - 24 VDC
Current Loop Sample Time μs 50
Velocity Loop Sample Time μs 100
Position Loop Sample Time μs 100
Sin/Cos Encoder DC Offset Range V 2 - 3.4
Maximum Sin/Cos Encoder Frequency kHz 200
Maximum Sin/Cos Interpolation - 2048 counts per sin/cos cycle
Internal Shunt Regulator - Yes
Internal Shunt Resistor - Yes
Mechanical Specifications
Description Units Value
Agency Approvals - CE Class A (EMC), CE Class A (LVD), cUL, RoHS, UL
Size (H x W x D) mm (in) 234.7 x 161.8 x 151.3 (9.2 x 6.4 x 6)
Weight g (oz) 4495 (158.6)

Sold & Serviced By:

Heatsink (Base) Temperature Range5
Storage Temperature Range
°C (°F)
°C (°F)
0 - 65 (32 - 149)
-40 - 85 (-40 - 185)
Cooling System - Natural Convection
Form Factor - Panel Mount
IP Rating - IP10
+24V LOGIC Connector - 2-port, 5.08 mm spaced, enclosed, friction lock header with threaded flange
AUX ENCODER Connector - 15-pin, high-density, male D-sub
COMM Connector - 9-pin, female D-sub

FEEDBACK Connector
Toll Free Phone: 877-378-0240
DC BUS / BRAKE RESISTOR Connector -
-
5-contact, 13 mm spaced, dual-barrier terminal block
15-pin, high-density, female D-sub
I/O Connector Toll Free Fax: 877-378-0249
MOTOR POWER / DC BUS Connector
-
-
26-pin, high-density, female D-sub
5-contact, 13 mm spaced, dual-barrier terminal block
POWER Connector [email protected] - 5-contact, 13 mm spaced, dual-barrier terminal block
Notes
1.
2.
www.servo2go.com
Can operate on single-phase VAC if peak/cont. current ratings are reduced by at least 30%.
Large inrush current may occur upon initial DC supply connection to DC Bus.
3. P = (DC Rated Voltage) * (Cont. RMS Current) * 0.95.
4. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements.
5. Additional cooling and/or heatsink may be required to achieve rated performance.

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 3 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

PIN FUNCTIONS

+24V LOGIC - Logic Power Connector

Pin Name Description / Notes I/O
1 LOGIC GND Logic Supply Ground GND
2 LOGIC PWR Logic Supply Input I

AUX ENCODER - Auxiliary Feedback Connector

Pin Name Description / Notes I/O
1 RESERVED Reserved -
2 RESERVED Reserved -
3 RESERVED Reserved -
4 PDI-8 + (PWM+ / AUX ENC A+ / CAP-B+) Programmable Digital Input or PWM or Auxiliary Encoder or High Speed Capture (For I
5 PDI-8 - (PWM- / AUX ENC A- / CAP-B-) Single-Ended Signals Leave Negative Terminal Open) I
6 PDI-9 + (DIR+ / AUX ENC B+ / CAP-C+) Programmable Digital Input or Direction Input or Auxiliary Encoder or High Speed Capture I
7 PDI-9 - (DIR- / AUX ENC B- / CAP-C-) (For Single-Ended Signals Leave Negative Terminal Open) I
8 PDI-10 + I
Programmable Digital Input (For Single-Ended Signals Leave Negative Terminal Open)
9 PDI-10 - I
10 SGN GND Signal Ground SGND
11 SGN GND Signal Ground SGND
12 SGN GND Signal Ground SGND
13 +5V OUT +5V Encoder Supply Output (Short Circuit Protected) O
14 PAI-4 + I
Differential Programmable Analog Input (12-bit Resolution)
15 PAI-4 - I

COMM - RS232/RS485 Communication Connector

Pin Name Description / Notes I/O
1 SELECT RS232/485 selection. Pull to ground (CN1-5) for RS485. I
2 RS232 TX / RS485 TX- Transmit Line (RS-232 or RS-485) O
3 RS232 RX / RS485 RX- Receive Line (RS-232 or RS-485) I
4 RESERVED Reserved -
5 ISO GND Isolated Signal Ground IGND
6 RS485 TX+ Transmit Line (RS-485) O
7 RESERVED Reserved -
8 RS485 RX+ Receive Line (RS-485) I
9 RESERVED Reserved -

DC BUS / BRAKE RESISTOR - Power Connector

Pin Name Description / Notes I/O
1 HIGH VOLTAGE O
DC Bus Output
2 POWER GND PGND
3 EXT External Brake Resistor Connection. -
4 DC+ Brake Resistor DC+. Connection for brake resistor. O
5 INT Internal Brake Resistor. Jumper to Brake Resistor DC+ to activate. -

FEEDBACK - Feedback Connector

Pin Name Description / Notes I/O
1 COS + I
Sold & Serviced By:
2 COS -
Cosine Input
I
3 SIN + I
Sine Input
4 SIN - I
5 SGN GND Signal Ground SGND
6 HALL A+ I
Commutation Sensor Input (For Single-Ended Signals Leave Negative Terminal Open)
7 HALL A- I
8 HALL B+ I
Commutation Sensor Input (For Single-Ended Signals Leave Negative Terminal Open)
9 HALL B- I
10 Toll Free Phone: 877-378-0240
REF MARK + Reference mark from sine/cosine encoder I
11
12 Toll Free Fax: 877-378-0249
HALL C+
HALL C-
Commutation Sensor Input (For Single-Ended Signals Leave Negative Terminal Open)
I
I
13
14 [email protected]
+5V OUT +5V Encoder Supply Output (Short Circuit Protected)
Programmable Analog Input (12-bit Resolution)
O
I
15
www.servo2go.com
REF MARK - Reference mark from sine/cosine encoder I

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 4 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

I/O - Signal Connector

Pin Name Description / Notes I/O
1 PDO-1 Isolated Programmable Digital Output O
2 OUTPUT COMMON Digital Output Common OGND
3 PDO-2 Isolated Programmable Digital Output O
4 PAI-1 + (REF+) I
Differential Programmable Analog Input or Reference Signal Input (16-bit Resolution)
5 PAI-1 - (REF-) I
6 PAI-2 Programmable Analog Input (12-bit Resolution) I
7 SGN GND Signal Ground SGND
8 OUTPUT PULL-UP Digital Output Pull-Up For User Outputs I
9 PDI-5 Isolated Programmable Digital Input I
10 PDO-3 Isolated Programmable Digital Output O
11 PDI-1 Isolated Programmable Digital Input I
12 PDI-2 Isolated Programmable Digital Input I
13 PDI-3 Isolated Programmable Digital Input I
14 PDO-4 Isolated Programmable Digital Output O
15 INPUT COMMON Digital Input Common (Can Be Used To Pull-Up Digital Inputs) IGND
16 SGN GND Signal Ground SGND
17 PDI-4 (STEP) Isolated Programmable Digital Input or Step I
18 PDI-6 (DIR) Isolated Programmable Digital Input or Direction I
19 PDI-7 (CAP-A) Isolated Programmable Digital Input or High Speed Capture I
20 ENC A+ OUT O
Emulated Encoder Channel A Output
21 ENC A- OUT O
22 ENC B+ OUT O
Emulated Encoder Channel B Output
23 ENC B- OUT O
24 ENC I+ OUT O
Emulated Encoder Index Output
25 ENC I- OUT O
26 SGN GND Signal Ground SGND

MOTOR POWER / DC BUS - Power Connector

Pin Name Description / Notes I/O
1 MOTOR A Motor Phase A O
2 MOTOR B Motor Phase B O
3 MOTOR C Motor Phase C O
4 POWER GND Power Ground (Isolated From Signal Ground) PGND
5 HIGH VOLTAGE DC Power Input I

POWER - Power Connector

Pin Name Description / Notes I/O
1 L1 I
2 L2 AC Supply Input (Three Phase) I
3 L3 I
4 CASE GND Case Ground PE
5 RESERVED Reserved -

Sold & Serviced By:

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249
[email protected]
www.servo2go.com

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 5 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

HARDWARE SETTINGS

Switch Functions

Setting
Switch Description
On Off
Bit 0 of binary RS-485 drive address. Does not affect RS-232
1 1 0
settings.
Bit 1 of binary RS-485 drive address. Does not affect RS-232
2 1 0
settings.
Bit 2 of binary RS-485 drive address. Does not affect RS-232
3 1 0
settings.
Bit 3 of binary RS-485 drive address. Does not affect RS-232
4 1 0
settings.
Bit 4 of binary RS-485 drive address. Does not affect RS-232
5 1 0
settings.
Bit 5 of binary RS-485 drive address. Does not affect RS-232
6 1 0
settings.
Bit 0 of drive RS-485 baud rate setting. Does not affect RS-232
7 1 0
settings.
Bit 1 of drive RS-485 baud rate setting. Does not affect RS-232
8 1 0
settings.

Additional Details
The drive can be configured to use the address and/or bit rate stored in non-volatile memory by setting the address and/or bit
rate value to 0. Use the table below to map actual bit rates to a bit rate setting.

Baud Rate (kbps) Value For Bit Rate Setting

Load from non-volatile memory 0
9.6 1
38.4 2
115.2 3

Sold & Serviced By:

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249
[email protected]
www.servo2go.com

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 6 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

MECHANICAL INFORMATION

+24V LOGIC - Logic Power Connector

Connector Information 2-port, 5.08 mm spaced, enclosed, friction lock header with threaded flange
Details Phoenix Contact: P/N 1777808
Mating Connector
Included with Drive Yes

1 LOGIC GND
2 LOGIC PWR

AUX ENCODER - Auxiliary Feedback Connector

Connector Information 15-pin, high-density, male D-sub
TYCO: Plug P/N 1658681-1; Housing P/N 5748677-2; Terminals P/N 1658686-2 (loose) or
Details
Mating Connector 1658686-1 (strip)
Included with Drive No

SGN GND 10
PDI-10 - 9
PDI-10 + 8
PDI-9 - (DIR- / AUX ENC B- / CAP-C-) 7 4 PDI-8 + (PWM+ / AUX ENC A+ / CAP-B+)
PDI-9 + (DIR+ / AUX ENC B+ / CAP-C+) 6 5 PDI-8 - (PWM- / AUX ENC A- / CAP-B-)

15 PAI-4 -
14 PAI-4 +
13 +5V OUT
12 SGN GND
11 SGN GND

COMM - RS232/RS485 Communication Connector

Connector Information 9-pin, female D-sub
TYCO: Plug P/N 205204-4; Housing P/N 5748677-1; Terminals P/N 1658540-5 (loose) or
Details
Mating Connector 1658540-4 (strip)
Included with Drive No

5 ISO GND

3 RS232 RX / RS485 RX-

2 RS232 TX / RS485 TX-
1 SELECT

Sold & Serviced By:

6 RS485 TX+

8 RS485 RX+

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249
[email protected]
www.servo2go.com

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 7 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

DC BUS / BRAKE RESISTOR - Power Connector

Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block
Details Not applicable
Mating Connector
Included with Drive Not applicable

5 INT
4 DC+
3 EXT
2 POWER GND
1 HIGH VOLTAGE

FEEDBACK - Feedback Connector

Connector Information 15-pin, high-density, female D-sub
TYCO: Plug P/N 748364-1; Housing P/N 5748677-2; Terminals P/N 1658670-2 (loose) or
Details
Mating Connector 1658670-1 (strip)
Included with Drive No

HALL A+ 6 5 SGN GND

HALL A- 7 4 SIN -
HALL B+ 8 3 SIN +
HALL B- 9 2 COS -
REF MARK + 10 1 COS +

11 HALL C+
12 HALL C-
13 +5V OUT
14 PAI-3
15 REF MARK -

I/O - Signal Connector

Connector Information 26-pin, high-density, female D-sub
TYCO: Plug P/N 1658671-1; Housing P/N 5748677-3; Terminals P/N 1658670-2 (loose) or
Details
Mating Connector 1658670-1 (strip)
Included with Drive No

PDO-3 10 9 PDI-5
PDI-1 11 8 OUTPUT PULL-UP
PDI-2 12 7 SGN GND
PDI-3 13 6 PAI-2
Sold & Serviced By: PDO-4 14
INPUT COMMON 15
5 PAI-1 - (REF-)
4 PAI-1 + (REF+)
SGN GND 16 3 PDO-2
PDI-4 (STEP) 17 2 OUTPUT COMMON
PDI-6 (DIR) 18 1 PDO-1

Toll Free Phone: 877-378-0240 19 PDI-7 (CAP-A)

Toll Free Fax: 877-378-0249

20 ENC A+ OUT
21 ENC A- OUT
22 ENC B+ OUT

[email protected] 23 ENC B- OUT

24 ENC I+ OUT
25 ENC I- OUT

www.servo2go.com 26 SGN GND

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 8 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

MOTOR POWER / DC BUS - Power Connector

Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block
Details Not applicable
Mating Connector
Included with Drive Not applicable

5 HIGH VOLTAGE
4 POWER GND
3 MOTOR C
2 MOTOR B
1 MOTOR A

POWER - Power Connector

Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block
Details Not applicable
Mating Connector
Included with Drive Not applicable

4 CASE GND
3 L3
2 L2
1 L1

Sold & Serviced By:

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249
[email protected]
www.servo2go.com

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 9 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

MOUNTING DIMENSIONS

Sold & Serviced By:

Toll Free Phone: 877-378-0240

Toll Free Fax: 877-378-0249
[email protected]
www.servo2go.com

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 10 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com
 DigiFlex® Performance™ Servo Drive DPRAHIS-060A400

PART NUMBERING INFORMATION

Example: D P R A N I E - 0 1 5 A 4 0 0 -
Drive Series Customer Special
DP DigiFlex Performance Code used to identify customer
specials

Communication Revision
R RS232/RS485 A through Z (letters may be skipped)
C CANopen or RS232
Q SynqNet Max DC Bus Voltage (VDC)
080 80
Command Inputs 200 200
Analog (±10V) 400 400
AN
No Step & Direction 800 800
Analog (±10V)
AL
Low Voltage Step & Direction (5V)
Power and Logic Supply
Analog (±10V)
AH AC Input
High Voltage Step & Direction (24V) A
+24VDC User Logic Supply Required
No Analog
NL AC Input Only
Low Voltage Step & Direction (5V) N
No Logic Supply Required (Internal Supply)
No Analog, No Step & Direction
NN DC Input
(Communication Interface Only) B
Both Logic Supply Options (Internal or User)
DC Input
L
Digital I/O Logic Supply Required
I Isolated (24V) DC Input Only
D
T TTL (5V) Non-Isolated Internal Logic Supply

Motor Feedback Peak Current (A0 to Peak)

E Incremental Encoder and/or Halls 015 15
R Resolver 016 16
A Absolute Sin/Cos (Hiperface & Endat) 020 20
S Sin/Cos with Halls 025 25
030 30
040 40
060 60
100 100

DigiFlex® Performance™ series of products are available in many configurations. All models listed in the selection tables of the
website are readily available, standard product offerings.

ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for OEMs with volume
requests. Our Applications and Engineering Departments will work closely with your design team through all stages of
development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quick-
turn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease
your costs and time-to-market while increasing system quality and reliability. Feel free to contact Applications Engineering for
further information and details.

Examples of Customized Products

Optimized Footprint Tailored Project File
Private Label Software Silkscreen Branding
OEM Specified Connectors Optimized Base Plate
No Outer Case Increased Current Limits
Increased Current Resolution Increased Voltage Range
Increased Temperature Range Conformal Coating
Custom Control Interface Multi-Axis Configurations
Integrated System I/O Reduced Profile Size and Weight

Available Accessories
Sold & Serviced By: Controls offers a variety of accessories designed to facilitate drive integration into a servo system.
ADVANCED Motion
Visit www.a-m-c.com to see which accessories will assist with your application design and implementation.

Toll Free Phone: 877-378-0240 Filter Cards To Motor

Toll Free Fax: 877-378-0249
[email protected]
Drive(s)

www.servo2go.com
All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document.

Release Date: Revision: Advanced Motion Controls · 3805 Calle Tecate, Camarillo, CA, 93012
Page 11 of 11
11/5/2009 2.00 ph# 805-389-1935 · fx# 805-389-1165· www.a-m-c.com