<<Contents>>

Installation Manual
-SmartDVR Formula Hardware Installation
-SmartDVR Formula Software Installation

User Manual
-SmartDVR Formula Surveillance Mode
-SmartDVR Formula Search Mode
-SmartDVR Formula AVI Backup Manager Mode
-SmartDVR Formula Backup Manager
-SmartDVR Formula NetClient Mode
-SmartDVR Formula WebClient Mode

Compatible / Incompatible

SmartDVR Formula Hardware Installation

When you purchase INTOTECH DVR, you have to install DVR board in
users PC or DVR system. This is installation guide for Capture board
among INTOTECH DVR board. In case of installing INTOTECH Live
series board, please refer to Live series manual.
Minimum Requirement
CPU

Intel Celeron 1.7Ghz or higher

RAM

256 MB or higher

HDD

80 GB 7200rpm or higher
Intel i845 Chipset built-in motherboard

Motherboard

Ref In case of using analog audio, we recommend to

use Intel i865 Chipset built-in motherboard.

VGA

Refer to 115page

OS

Only Windows 2000, Windows XP

Direct X

DirectX 8.1 or higher

SmartDVR Formula Hardware Installation

1

DVR board & Extension video cable installation

Insert the DVR board to an empty PC slot in DVR system.

Video & Audio connection

Video input installation
DVR board: You connect to DVR board with 4ch video extension
cable or 8ch video extension cable.

Audio input installation

In case of connection MIC to MIC IN port of motherboard.
MIC connect to MIC IN port of motherboard.
In case of connection MIC to Audio IN port of DVR board.
MIC connect to Audio IN port of DVR board.
3

SmartDVR Formula Hardware Installation

* Connection to MIC (over 4ch)

Each DVR board supports various MIC input channel according to
model. When you use over 2ch MIC input, please connect
additional audio extension cable.
Board

Analogue audio

Digital audio

Sound Card

1 ch

1 ch

SP

2 ch

4 ch

1 ch

4 ch

1 ch

HP

8 ch

1 ch

RD

1 ch

Live 120

4 ch

1 ch

Live 480

8 ch

1 ch

- S board
S board supports only 1ch MIC input.

SmartDVR Formula Hardware Installation

- SP board
SP board supports 2ch MIC
input. Please refer to below
picture. Actual used MIC input in
audio extension cable is 2 port.

- H board
H board supports 4ch MIC input.
Please refer to below picture.

SmartDVR Formula Hardware Installation

- HP board
HP board supports 8ch
MIC input. Like below
picture, A part in DVR
board connects to B
part in audio extension
cable.

Digital audio installation

Audio quality of digital audio board is superior to quality of analogue
audio cable. You have to purchased digital audio board. Digital audio
board is compatible with SP board and Live series board.

SmartDVR Formula Hardware Installation

3

P/T/Z Installation

Some cameras support pan/tilt/zoom/focus function. In order to use

P/T/Z camera, you need to connect P/T/Z cable.
[A] connecter: Connect P/T/Z cable to COM port of DVR systems
[B] connecter: Connect P/T/Z cable to DVR board.
[C] part: Connect to receiver (camera). When you install a few
cameras, you use cable like picture.

SmartDVR Formula Hardware Installation

Ref P/T/Z cable Connection for each board.

RD(Real Display) board installation

When you install RD board with capture board, you are able to view
camera image in real-time speed. (30fps display per channel / total
480fps display) You install RD board in empty slot in DVR system. You
connect RD board and capture board with IDE cable.

SmartDVR Formula Hardware Installation

Notice RD board has to be installed S, H, HP board together. (RD
board is only displaying board)
Ref How to connection TV out in RD board.
When you use RD board, TV out is connected to TV out port of
RD board.

I/O board installation

When you install I/O board in DVR system. You are able to connect
various sensors and alarms.
I/O board supports total 8 IN / 8 OUT with both extension I/O board and
basic 4 IN / 3 OUT. When you connect 2 set I/O board, maximum I/O
function is 16 IN / 16 OUT.

SmartDVR Formula Hardware Installation

Back panel connection port in industrial case.
In case of industrial system with back panel connection, you are
able to use I/O IN/OUT separately.
Connection port of I/O extension board cable.
It is connected to I/O extension board.
DVR board connection port
It is connected to DVR board in DVR system.
Master/Slave connection port
When you install I/O board (2EA, 16 IN / 16 OUT)

10

SmartDVR Formula Hardware Installation

Master/Slave setup dip jumper
It designates Master/Slave part at each board.
(Master: Jumper install / Slave: Jumper uninstall)
E.g. Disconnection between DVR board and I/O board
(Extension board)

11

SmartDVR Formula Software Installation

Software installation manual introduction

SmartDVR Formula
It is software to execute INTOTECH DVR system.
It is fundamental software against other software INTOTECH
provides and you have to install it in INTOTECH DVR system.
NetClient
INTOTECH DVR system connects to DVR system at remote site and
record transferred image in client system.
It is software which connects to DVR system at remote site through
20408 port and monitors and control.
WebClient
INTOTECH DVR system is able to connect to DVR system at remote
site and monitor and control P/T/Z camera in Web (Internet Explorer)
It is software to monitor and control DVR system at remote site in
Web. When it is installed in DVR system, user does not need to
install additional software to monitor DVR at remote site by installing
WebClient installation file automatically through 26540 port after auto
downloading.
Notice This is used for Apache Web server.
User has to change 80 port into 26540 port to use WebClient with
Apache port change software in CD or www.intotech.co.kr. Usually,
most of communication companies closes 80 port.

12

SmartDVR Formula Software Installation

Software

Installation

You are able to install INTOTECH SmartDVR Formula software by

using SmartDVR Formula CD-ROM or downloading from INTOTECH
website. www.intotech.co.kr.
Software CD consists of Server Package (Main program, WebClient
program, Apache server, Netclient, AVI codec. User manual is also
available from S/W CD.
1. DVR Server Package Installation
Insert SmartDVR Formula CD into CD-ROM drive or run DvrSetup.exe
file; the following installation screen will appear.

Click the first button, DVR Server package will be proceeded.

Installation step : SmartDVR Web Applet(Apache) -> WebClient ->
SmartDVR Formula
13

SmartDVR Formula Software Installation

SmartDVR Web(Apache Web Server) installation
Click Install Server Package button in provided CD, installation will be
proceeded.

Installation wizard tool will appear. Click [Next]

14

SmartDVR Formula Software Installation

Read the License Agreement and if you agree to the contents, select [I
accept] and click [Next].

Click [Next] after checking server information of Apache server.

15

SmartDVR Formula Software Installation

Insert Network Domain, Server Name, Administrators E-mail Address.
In case there is not any specific info, please insert as below.
Network Domain: somenet.com
Server Name: www.somenet.com
Administrators Email Address: [email protected]
Select [Run as a service for All Users Recommended] and click [Next]

16

SmartDVR Formula Software Installation

Select Setup Type as [Complete] and click [Next]

Click [Next] without change of setting.

Notice Please do not change the directory

17

SmartDVR Formula Software Installation

After the setting is finished, click [Install] and start installation.

After the installation is done, click [Finish] to end the installation

program.

18

SmartDVR Formula Software Installation

Confirm whether the apache server port has been changed to
26540 after the apache installation is finished.

Notice Default port is 80 for apache web server. If the port is not
changed after apache web server is installed, you would not be
able to use WebClient program from external environment.
Therefore port must be changed.
WebClient Installation
After the Installation Wizard Tool is appeared, click [Next].

19

SmartDVR Formula Software Installation

Check the contents of License Agreement; if you agree to the contents,
click [Yes].

After the installation is done, click [Finish].

20

SmartDVR Formula Software Installation

SmartDVR Formula Installation
After Installation Wizard Tool is appeared, click [Next].

Check the details of License Agreement; if you agree to the contents,

click [Yes].

21

SmartDVR Formula Software Installation

Check the added or fixed functions of currently installed DVR Server
version and click [Next].

After choosing [Destination Folder] for installation, click [Next].

22

SmartDVR Formula Software Installation

After the installation is done, click [Finish].

Driver Installation: Wizard automatically installs drivers according to

each board type.

Please reboot PC after all the installation is finished.

23

SmartDVR Formula Software Installation

SmartDVR Formula Uninstallation
In case of Up-grade SmartDVR Formula in new version, or there is
problem in setup version, please remove by method as below.
Notice To keep stability of DVR system, SmartDVR Formula and other
program need to be deleted and removed certainly as below
click control panel after clicking beginning button of windows.
(It can be in different position according to kind of OS)
Click [Add/Remove Program] .
After choosing SmartDVR Formula by mouse, click [Add/Remove
Program]

2. NetClient Installation
If click Install Client Package button of setup program in offered CD,
NetClient setup will be proceeded.

24

SmartDVR Formula Software Installation

After Installation Wizard Tool is appeared, click [Next].

After choosing [Destination Folder] for installation, click [Next].

25

SmartDVR Formula Software Installation

After the installation is done, click [Finish].

NetClient Uninstallation
In case of Up-grade NetClient Formula in new version, or there is
problem in setup version, please remove by method as below.
Notice To keep stability of DVR system, NetClient and other program
need to be deleted and removed certainly as below
Click control panel after click [beginning] button of windows.
(It can be in different position according to kind of OS)
Click [Add/Remove Program]
After choosing NetClient by mouse, click [Add/Remove Program]

26

SmartDVR Formula Software Installation

3. AVI Codec Installation

When wish to watch image that backed up by AVI Backup Manager in
DVR system or other computer, user can see though setup Intotech
AVI Codec certainly.
If click Install AVI Codec button, NetClient setup will be proceeded.

AVI Codec Installation diagram.

27

SmartDVR Formula Software Installation

After the installation is finished, click [Finish].

Ref: SP Digital Audio Installation

In case of using digital audio in SP60 DVR systems with only Windows
2000 OS, Digital Audio Driver must be setup by by hand.
Clicks the [Beginning] button-[Control panel]-[System-Hardware][Device administrator] and executes device administrator.

28

SmartDVR Formula Software Installation

After choosing [WDM DVR Audio Driver] by mouse, choose the [Drive
Up-date] and click right button
Ref If see the screen as below, choose the [Yes, this time only] and
then click [Next] button

After choose [Advanced setting] at list or specification position, click

[Next] button.

After select [Driver search (S)] that is the most suitable at this position,
select [when search, includes next position] and specifies path as follows
29

SmartDVR Formula Software Installation

C:\Program Files\SFDVR\Driver\9x2k\SPLUS
Click [Search] button
If finish installation as below, click [next] button and proceed to next step

Choose [WDM LIVE Audio Driver] and then click [Next] button

30

SmartDVR Formula Software Installation

If the information that Digital Audio Driver is placed normally,
Click [Finish] button

After finishing installation, if confirm [device administrator] again, it will

be seen as below
Progress remaining [WDM DVR Audio Driver] again in same process.

31

SmartDVR Formula Software Installation

If digital audio driver installation is finished normally, [WDM LIVE Audio
Driver] item as following is registered 2pcs.
Reboot the computer to operate driver normally.
After rebooting computer, confirm [Configuration>General] running DVR
program
If it is installed normally, confirm that Audio Device is placed from 1to 4
as below.

32

SmartDVR Formula Software Installation

If use audio channel from1 to 4, and channel 5 is used MIC monad of
audio card, install audio channel as following.
The case of below is to just use video channel from 1 to 5
When use video channel until 1-5 below occasion,
Click [apply] button and completes configuration.

33

SmartDVR Formula is the main program which takes part as the

most important role in INTOTECH DVR System, and acts as the
Server role for other additionally supported program.
SmartDVR Formula supports maximum 16 video channels and 1~9
audio channels according to board. Low resolution(less storage) and
high resolution (more storage) for each channel is supported and 9
audio channels can be adjusted freely. By various split-screen display
modes and color adjustment, optimized image can be realized
according to the environment.
Existing analog CCTV equipments such as Sensor & Alarm, P/T/Z
camera, Video Out, etc. are perfectly compatible. Image or E-mail
can be transmitted over the network for users to observe from
remote site without having the inconvenience to stand in front of the
DVR System. Max. 30 user accounts can be created to grant
authorization by user-level, and real time monitoring is available by
connection over the network.

34

Minimum Requirement
CPU

Intel Celeron 1.7 GHz or higher

RAM

256 MB or higher

HDD

80 GB 7200rpm or higher

Motherboard

Intel i845 Chipset or higher

VGA

Refer to 115page

OS

Windows 2000, Windows XP

(Windows 98 and ME is not supported.)

Direct X

DirectX 8.1 or higher

Min. Required
Space when
installation

30 MB

Others

Graphic Driver and Sound Card are required as

compulsory.

35

SmartDVR Formula Surveillance Mode

SmartDVR Formula Surveillance Mode

Control Panel
Screen Partition Panel
P/T/Z Control Panel
Channel Type Selection Panel
Real Time Audio Volume Control Panel
DVR Status Information Panel

36

SmartDVR Formula Surveillance Mode

1

Control Panel

Users can run search program, record images, open configuration

screen, etc. from control panel.

Search Button: You can run search program.

Configuration Button: You can open configuration mode to
change system setup.
Lock Button: Lock function is supported to prevent program setup
changes or search program run.
REC Button & All Button:
To record specific channels Click left mouse button on specific
channel and click REC button.
To record all channels Click ALL buttons and click REC button.
2

Screen Partition Panel

You can select 7 types of various display modes
and use full screen mode, auto-switching display,
etc. to setup the screens to change automatically.

P/T/Z Control Panel

You can control the cameras if P/T/Z camera is connected to the DVR
System. First use left mouse button to click on the channel you wish to
control, and use the buttons in P/T/Z Control Panel to support various
functions.
37

SmartDVR Formula Surveillance Mode

4

Channel Type Selection Panel

Click a specific channel to
enlarge the screen.

Real-Time Audio Volume Control Panel

If audio input setup is done by each channel
from [Configuration] - [General], you can use
audio volume control bar to control the realtime audio volume.

DVR Status Information Panel

Indicates the number of channels connected by Internet( TCP ) or
Modem ( MODEM ). If there are no free space available in
recording HDD, Disk Full will be indicated in red color.

38

SmartDVR Formula Surveillance Mode

Configuration Setup
Configuration is consisted of detailed items characterized by functional /
applicable aspect. Video resolution, image quality, motion detection
recording, digital input/output, schedule, P/T/Z receiver protocol,
network etc. setup are available.
General

Start Setup
Auto Start at Windows starting: DVR program automatically runs
when DVR system is turned on.
Max Size at Starting
DVR Program is setup as full screen to prevent use of other
programs.

39

SmartDVR Formula Surveillance Mode

Exit Setup
When shutting down SmartDVR Formula program, setup to shut
down SmartDVR Formula program only or shut down DVR System
power or auto-reboot system.
Audio Setup
Setup the gain of Audio Input. AUD1 ~ AUD8 is gain control for
Audio channel supported from DVR Board or Digital Audio Board.
Set the gain to minimum (0) when use of amplified mic. (E.g.:
model with built-in amplifier circuit)
Sound Card controls the Sound Card volume for audio input.
Video / Audio Setup
Input Camera Type Setup
NTSC: Korea, USA, Japan, Australia (some region), North America
(some region)
PAL: Other regions excluding NTSC (China, Europe, South
America, etc.)
Channel Selection
Select the channel for surveillance. Do not select the camera which
is not connected to DVR System.
Video Resolution Setup
Setup the recording resolution for video images. There is standard
resolution and high resolution.
Ref NTSC 320X240, 640X480 / PAL 360X288, 720X576

40

SmartDVR Formula Surveillance Mode

Channel Configuration

Channel Caption Input

Insert the description of the area that is under camera surveillance.
Caption Setup
Surveillance Mode
Setup to indicate the channel number and surveillance area on
the video images from main program.
Search Mode
Setup to indicate the channel number and recording time on
the video images from search program.
Caption Font and Color Setup
You can setup caption font & color of caption according to
channel number, camera surveillance area recorded time etc.
Video Source
You can setup brightness, contrast, hue, saturation and
sharpness to optimize video quality.
41

SmartDVR Formula Surveillance Mode

Store Configuration

Store Disk
Indicates HDD which is installed to DVR system. (Movable disk is
not included.)
(Check() HDD to use as recording device.)
Notice In case camera image is stored in hard-disk which has
operating system, if hard-disk will be full, system can be shut down
or repeat rebooting.
Disk Information
Indicates selected HDD information from Store Disk.
Overwrite
The oldest image data will be erased and new image data will be
recorded when the free HDD space is lesser than the minimum
free space (Default: 1024 MB).

42

SmartDVR Formula Surveillance Mode

Notice You can use the HDD with no shortage in space if you use
overwrite function. However this means that the oldest data will be
automatically erased. Therefore it is recommended to backup
important data in advance by using Backup Manager program for
your preservation purpose.
Recording Quality and Recording Frame Rate setup
Max. recording frame rate and image quality can be setup by each
channel.
Ref Recording size of 1 frame by image quality and resolution is as
below.
Image Quality

Resolution

Recording Size(KB)

Low

Low Resolution

2.5 KB

Low

High Resolution

6.0 KB

Medium

Low Resolution

3.7 KB

Medium

High Resolution

10.0 KB

High

Low Resolution

5.0 KB

High

High Resolution

15.0KB

Watermark
Image tampering can be prevented by inserting watermark in
every frame.
Normal: Watermark by the form of DVR will be inserted.
User Define Mark: Any type of watermark can be inserted by
designing your own.

43

SmartDVR Formula Surveillance Mode

Network Configuration

Server function setup

Enable TCP/IP server
This enables the system to act as a server for remote surveillance
through internet connection. Remote surveillance using Client
program and Web Browser is available when private line is used to
connect to internet.
Enable the Modem Server
This enables the system to act as a server for remote surveillance
through PSTN network. (General modem using telephone line)
Remote surveillance through Client program is available when
modem is installed in the system to connect PSTN network. Please
notify remote surveillance by Web Browser is not available.
44

SmartDVR Formula Surveillance Mode

Network Information
You can check the system IP address & MAC address.
Ref It is likely that the DVR System is using dynamic IP if the IP is
frequently changed without noticing or when DVR System is
rebooted. Our DHS Service is recommended for dynamic IP users
who connected to DVR System for remote surveillance.
User Limit
Network connection port
You can change the connection port for remote surveillance
function. (20408 port is setup as basic.).
Max. Connection no
Maximum number of connection to the DVR System for remote
surveillance function can be limited.
User of Sharing IP
Use this option when network is connected by internet router to
DVR system.
IP Manager Setup
Remote surveillance for specific IP can be enabled or disabled.
Dynamic IP ID authentication & registration
Insert the ID you have registered to our DHS Service and receive
authentication. (refer to 114p)

45

SmartDVR Formula Surveillance Mode

Schedule Configuration

Schedule Chart
You can setup the schedule of each channel using the left mouse
button click or drag.
You can remove the schedule by using right mouse button click or
drag.
Clear: Schedule setup of current channel will be removed.
Apply All: Schedule setup of current channel will be applied to all
channels.
Set Schedule Function
Schedule will be enabled only when the check box is initialized.
Schedule Type
After selecting from the 3 schedule types, use your mouse to setup
the schedule in schedule chart.

46

SmartDVR Formula Surveillance Mode

Maintenance Configuration

Windows Info
You can check the Windows and system information of DVR
System.
DVR Version Info
You can check the DVR Systems each version and board type.
DVR System
You can check the version and size of SmartDVR Formula
program.
System Maintain
This is a function which checks the DVR System & video data files
for any errors when starting SmartDVR Formula program.
Normal Check Mode: This checks for video data index and
program files.
Full Check Mode: System integrity is added from the normal
check mode so the duration time can be slow.
47

SmartDVR Formula Surveillance Mode

System Auto Reboot
You can setup to re-boot DVR System regularly.
This is recommended for stable Windows operation and data
verification.
System Log- You can run system log viewer.
Event Recording Setup

Sensor
You can use by clicking enable the sensors. Click to initialize the
installed sensor of each channel and select sensor type.
Ref Sensor Type
NO (Normal Open)
NO type sensor will be closed when there is detection. You do not
need to setup additionally from our setup configuration.
NC (Normal Close)
NC type sensor will be opened when there is detection. You need
to initialize by clicking the NC button below the sensor number
button.
48

SmartDVR Formula Surveillance Mode

Action / Digital Output
You can setup the automatic action which DVR will carry out when
sensor is triggered.
Enable the Event Recording
You can record the channel for [Duration: setup from ] when
sensor is triggered.
Enable the Warning Sound
Previously setup wave file will be run from [Warning Sound: setup
from ].
Send E-mail at Detection
Still image will be transmitted to the e-mail address which can be
setup from [Configuration>E-mail] when sensor is triggered.
Enable the Digital Output
Various output devices (warning light, siren, warning speaker, etc.)
will be activated when sensor is triggered.
Warning Sound
You can freely setup the warning sound that will be activated when
sensor is triggered.
Duration
You can setup the duration time of warning sound or recording
when sensor is triggered. For example if you setup 10sec, the DVR
will record and make warning sound for 10sec.
Motion Detection
This function will be activated when there is motion detection in
specific area of image.
You can either record or send still image by e-mail.
Detection Area Setup
You can setup the area you wish to detect motion by using mouse
drag on preview image.
Set Motion
The channel where motion is occurred will be indicated in blue
color from surveillance screen.
Motion Recording
Image will be recorded when motion is detected.
Draw Small MD Box
The area where motion is detected will be indicated in small green
boxes.
49

SmartDVR Formula Surveillance Mode

Pop-Up at MD
The channel which has motion detection will be viewed in full
screen mode for the duration time(pop-up time).
E-mail transmission at motion detection
The motion detected image will be transmitted to the e-mail
address which is setup from [Configuration>E-mail]. For more
detailed information, please refer to [Configuration>E-mail] function
description in this manual.
Sensitivity setup
You can setup the sensitivity for motion detection. Detailed
movements can be detected if you increase the sensitivity.
Duration Time
You can setup the duration time for [Pop-up channel at MD]
function.
Receiver Configuration

50

SmartDVR Formula Surveillance Mode

Port
Select the serial port where P/TZ camera or receiver is connected.
Receiver Address
Setup the P/T/Z camera or receiver address according to video
channel.
Ref Most of the P/T/Z cameras which are used in the market have
camera address. Camera address can be setup by the deep switch
in the camera or OSD menu.
If the address you have setup from DVR and the camera address is
not the same, P/T/Z function will not be operated so make sure
that the setup is same.
Device Type
You can select various P/T/Z camera or receiver protocol by using
your mouse.
The protocol should be one and equal even though you install
various kinds of P/T/Z camera or receiver.
Extend Function
Swap vertical command (Up/Down)
Vertical command which is transmitted to the P/T/Z camera will be
opposite.
Swap horizontal command (Left/Right)
Horizontal command which is transmitted to the P/T/Z camera will
be opposite.

51

SmartDVR Formula Surveillance Mode

Preset Configuration

Single Mode
You can select the video channel which is connected to the preset
camera.
Preset can be setup additionally by each channel.
Scenario List
Presets which have been setup will be composed into one order
diagram.
When [Scenario RUN], it will be run by the order in scenario list
and preset.
Preset Setting
Scenario No- Scenario number you have selected will appear.
Preset No- Preset which is under add/modify will appear.
Delay Time
You can setup the delay time for the current preset location which
is under add/modify.
52

SmartDVR Formula Surveillance Mode

Control Panel
Setup the current preset location by using P/T/Z button.
Add Button
You can record the current location in editing Preset and also apply
to scenario list at the same time.
Modify Button
Selected preset location and delay time can be modified to the
information that you have changed to.
Delete Button
Selected preset from the scenario list will be deleted.
But, camera location which is saved in the preset camera will not
be deleted.
Reverse Scan
Scenario list will be run in round circulation.
) Preset 1 Preset 2 Preset 3 Preset 4 Preset 3
Preset 2
Scenario RUN and PAUSE
Scenario RUN: Preset will be run from the top scenario list to the
bottom. Scenario will be stopped if you click the left mouse button
again.
PAUSE: Scenario which is being run will be paused.

53

SmartDVR Formula Surveillance Mode

Video Output
You can use video output function if you use with additional analog monitor.
Notice It has no relation with [Configuration>General], switching
display function.

Enable the TV Out Rotation

You can setup the images to be automatically displayed in
sequence when analog monitor (CCTV Monitor) is connected to DVR.
Single Mode
You can select specific channel to be viewed one at a time if you
do not wish to view by display in sequence from analog monitor.
Rotation Mode Time Gap
If you use automatic display sequence function, you can setup the
converting time to channel.
Rotation Mode Channel
You can select channels to display in sequence. For example if 1, 5,
7, 8, CH is selected,1, 5, 7, 8CH will be displayed in sequence from
analog monitor.
54

SmartDVR Formula Surveillance Mode

E-mail Function Configuration

Mail Server
Insert mail server address of the sender.
Ref E-mail function supports most of the mailing service but some
mailing services are not supported. Please refer to next page for
information regarding supported mail server list.
Sender
Insert the name and e-mail address of the person who sends the
mail.
Message Recipients
To - Insert the e-mail address of the person who receives.
Cc - Input e-mail addresses of other recipients.
Bcc - Input e-mail address for blind carbon copy.
E-mail Timer Setting
Setup e-mail response time after motion is detected or sensor is
triggered.
55

SmartDVR Formula Surveillance Mode

User Management configuration

User List
Display list of user account had stored at present.
Select empty account that it is written [Not used]
If correct or erase user account, after select account by using
mouse, correct or erase.
User information
Display selected user's ID, password etc.
User information renewal: Click at user account creation or
alteration
Account delete: Erase selected account at present.
Accessible local function
It is power establishment connected with function use in DVR
System
Can use in function checked in check box in case of loge in to
relevant user account in network
56

SmartDVR Formula Surveillance Mode

Accessible Network function
Establish power that can connect using NetClient or WebClinet in
remote.
Accessible channel
Establish access privilege that user account can see. Only,
because SmartDVR Formula Search is excepted in setting, user
account that establish channel access privilege persuades search
power revocation.
Ref Screen configuration in RD(Real Display) Board
After click right button of mouse, if select [Display Setting] Menu,
Can do display setting of RD Board in monitoring screen of DVR
System which is attached RD Board
Notice This setting is related only for image that is seen in
monitoring mode,, and control about actuality stored image
existent environment establishment > that do in channel setting
desire .
Auto Gain Control: control Gain of inputted video signal
automatically.
Gain Control: in case of check [Enable Auto Gain Control], user
directly can control Gain.
Edge Control: It is function that handle line of guard of screen
more clearly. Can see image of clearer boundary line by checking
[Enable Edge Control], but there are a lot of noises so much.
Display Color Setting: control Bight / Contrast saturation for the
better monitoring.

57

SmartDVR Formula Surveillance Mode

Application use
Kind and resolution establishment of camera
When SmartDVR Formula S/W is
installed, Formula has activated one
channel. So, User must do early set
depending on used environment.
Click environment establishment button
and selects [general] tap.
Video Auto Setting
NTSC: Korea, the United States of
America, Japan, Australia (some
area), South America (some area)
etc.
PAL: Area (China, Europe, South
America etc.) except NTSC area.
Activate channel of Linked camera.
Ref Cancel channel that is not
connected to camera.
Establish resolution of each channel.
Can select High resolution mode (NTSC: 640x480 , PAL
720x576)and low resolution mode. (NTSC: 320x240, PAL:
360x288 ) High resolution mode has good picture quality, but file
size is bigger, low resolution mode has average quality but file size
is smaller.
Image picture quality configuration
User can establish picture quality of
image of each channel according to
users environment.
Click configuration button and selects [channel] tap.
Setup each image picture quality in [image quality] below right side
after select channel to setup using [channel selection combo box] such
as left side picture.

58

SmartDVR Formula Surveillance Mode

Audio establishment
When SmartDVR Formula S/W is installed, all audios become
inactivation. Therefore, in order to use audio, user must set audio per
channel.
Each channel different audio channel assignment
Click configuration button and selects
[general] tap
Establish audio in channel which has
audio or is close camera.
Only, audio of each channel can not
establish overlap
Audio input control
Click configuration button and selects [general] tap.
Change audio input establishment according to actuality use
environment. Only, in case of setting amplification microphone which
has amplification circuit, built-in usually by 0
Motion detection setup
It is function that act in case of motion was detected in specific area
that user defines.
If establish in motionless place averagely, holding period can increase
because storage capacity of image decreases.
Click [event] tap after click configuration button.
By another method, click [present, channel setup] after click mouse
right button in channel to establish motion watch in monitoring screen.

59

SmartDVR Formula Surveillance Mode

Do drag by a mouse on preview
screen and designates motion
watch area.
Click [motion setup] button and
activates motion watch function. If
do not activate [motion setup]
button motion watch function does
not act.
Establish DVR Systems action in
case of motion was detected.

Save Motion perception

When motion happens, establish
to store picture.
To paint small MD box
In case of motion was detected in selected zone, small green box
traces movement.
Channel extension at motion detection.
It is function that shows channel which is detected in full screen
during appointed time( reference : continuance time)
E-mail transmission at motion detection
Transmit display of when motion is detected to E-mail address that
detected in [configuration> e-mail] in case of motion was detected
in selected zone. More detailed contents can get from back
[configuration> e-mail] function representation.
Sensitivity By raising responsiveness, user can detect small motion.
set channel extension time of [channel extension when sense
motion] function.

60

SmartDVR Formula Surveillance Mode

Sensor and digital output Configuration

Establish Linked sensor and digital output to DVR System.
Supply maximum 16 sensors and 16 digital outputs in this DVR System.
(Only, it is function that can use though I/O Board)
Can be acted organically connecting each sensor or digital output
device(alarm, lighting, warning sound etc.) to camera channel.
Sensor establishment
Move to [configuration> event]
First, select image channel
that adjoin with sensor
Check [sensor use] check
box.
Select
port
number
connected to sensor.
Notice Sensor that is not image channel is Linked channel. Refer
to Sensor/Digital Output SETUP of 9page if sensor gets a line for
Linked channel.
Setup Sensors kind.
Sensor can classified by two types.
NO (Normal Open)
NO type of sensor is kind that is short-circuited when was sensed
at normal times. Need not to establish apart in this setup.
NC ( Normal Close)
NC type of sensor is kind that is short-circuited at normal times.
When connect NC type of sensor, use after activate clicking NC
button of sensor number button under.
Set of sensor was completed.

61

SmartDVR Formula Surveillance Mode

Digital output Configuration

Move to [configuration>event.
Check [Enable the digital output] check.
Digital output device selects Linked port number.
Notice It is channel
connected digital output
device not image channel.
Refer to Sensor/Digital
Output SETUP of 9page
if want to get information
of channel that linked
digital output device.
Establish kind of digital output device..
Digital output device can be classified by two types greatly.
NO (Normal Open)
NO type of digital output device is kind that is short-circuited when
was sensed at normal times.
Need not to establish apart in setup.
NC (Normal Close)
NC type of digital output device is kind that is short-circuited at
normal times.
When connect NC type of sensor, use after activate clicking NC
button of digital output device number button under.
Set of digital output device was completed.

E-mail setup
If use together E-mail and motion watch or sensor watch, can receive
still image of relevant channel by E-mail in case of motion or sensor is.
Input mail server address of side of sender.
E.g. www.yahoo.co.kr / smtp.intotech.co.kr
Input information of side of sending mail.
62

SmartDVR Formula Surveillance Mode

Only, E-mail site that is
recorded to E-mail address
should be equal with 's [mail
server].
E.g.
E-mail
server:smtp.intotech.co.kr / Email: [email protected]
Input email address of recipient
TO: E-mail address of recipient
CC: input E-mail address of
other recipients
BCC: input E-mail address for
Blind
Setup E-mail response time after sensor has been triggered.
Ref E- Mail function does not support mailing. Therefore,
encourage test certainly after establish E- mail function.
If set time so shortly in case of watching continuous motion, too
many mails can be transferred to a recipients.
Also, encourage that setup to channel that can get action less and
clean image if is possible.
User account Configuration
Because SmartDVR Formula creates user account of maximum 30,
each user particularly can use different authorization levels.
move to [configuration > user
management].

Select segment that is

written [Not used] in user
list BY mouse click.

63

SmartDVR Formula Surveillance Mode

Input ID and password that
want to make new user
information and input
password equally in
[password confirm].
Click [modify user
information] button creates
user account.
Accessible local function
Setup DVR Systems
authorization level. When
connect in remote, act
according to user
authorization level.
Setup authorization levels
that can watch and search
with connecting in remote control
Establish authorization that can Watch-screen by particularly
channel in monitoring screen or remote monitoring.
Receiver Configuration
Setup in case of connected camera that includes P/T/Z function to DVR
System.
Move to [configuration>receiver]

Offered P/T/Z Cable establishes Linked COMPORT.

Usually, setup to Com1 or Com2

64

SmartDVR Formula Surveillance Mode

Select P/T/Z camera or receiver's kind.
If actuality value does not coincide with established value, P/T/Z
does not act.

Setup receiver address.

Establish address value by 8 if connected camera that have
address 8 to channel 1.
Receiver address is different according to P/T/Z camera or
receivers kind, setup with reference relevant manual

Preset Configuration
Setup when camera that has preset function connects to DVR System.
Camera move automatically according to appointed coordinates and
can watch several points.
Notice All P/T/Z cameras do not support preset function. Refer camera
manual about support availability of preset
function or inquires it manufacturing company,
Move to [configuration> preset]
Select channel to setup scenario in one
output mode.
Indicate preset number to save or
change present Position.
Setup camera position to use P/T/Z
buttons.
Using addition button
(in left side scenario list register)
Use correction / delete button in case of
correct or Erase preset that is already
registered.

65

SmartDVR Formula Surveillance Mode

Click (if click scenario list preview
screen move automatically to
camera position stored in preset)
scenario beginning button after
confirm whether was registered
properly in left side scenario list.
If repeat same process moving by
again 2times, user can Register
preset of maximum 32.
Network setup
It is service that can see image in remote place using specification ID
without necessity to make sure IP changed continuously in DVR
System which linked in dynamic IP.
Move
to
[configuration>
network].
Make sure whether was
checked to [TCP/IP server
use] or not. Please check if
was not checked.
Input ID that subscribed for
DHS service and clicks
[register Dynamic IP User
ID] button.

66

SmartDVR Formula Search Mode

SmartDVR Formula Search Mode

SmartDVR Formula Search allows users to search by time/date & play
recorded images and audio. Support saving of still image by .bmp
format, printing of still image, watermarked .bmp file of each image.

Control Panel
Playback Control Panel
Screen Partition Panel
Data Search Process Panel
Audio Volume Control Panel

67

SmartDVR Formula Search Mode

Control Panel

Control panel supports function that convert to watch mode or call data
or do various backup function.

Surveillance Mode Button: Converts to surveillance mode.

Date Search Button: Search recorded image of other date by
pening calendar
Save Button: Save still images of selected channels (bmp)
Print Button: Print image of selected channels.
Watermark Viewer Button: Run Watermark Viewer to view
watermark of recorded original image.
AVI Backup Manager switch Button: switch over AVI Backup
Manager mode Refers to 73page for more detailed operation.
Backup Manager switch Button: switch over backup Manager
Mode that can backup important data to Hard or CD
Convert to Backup Manager Mode that can backup important data
to HDD OR CD.

68

SmartDVR Formula Search Mode

2

Playback Control Panel

Playback Button: Playback

Pause Button: Pause playing
Reverse Playback Button: playback reversely
2x Playback Button: Playback 2x speed.
4x Playback Button: Playback 4x speed
2x Reverse Playback Button: Playback reversly 2x speed.
Play Next frame Button: Playback frame by frame
Previous frame Reverse Button: Reverse Playback frame by frame
Playback Mode supports 4 channels or 1 channel viewing mode.
3

Screen Partition Panel

Support 8 kinds of various screen partition display.

Data Search Process Panel

Hour Select Button

In recorded data of selected hour is indicated in red color.
Daily Search Bar:
Recorded data is indicated in red. Daily search (0h:0m~23h:59m)
69

SmartDVR Formula Search Mode

Search point indication icon
By moving your mouse with left house button pressed, you can
conduct quick searches with search bar.
Hour
Indicate time to search at present.
Ref To search data quickly, drag Search point icon to left or right after
clicking pause button.
5

Audio Volume Control Panel

Control audio volume when replay of recorded data.

In case of recording audio on many channels, volume
control must be set individually.
Calendar
Click the button of SmartDVR Formula Search [Load Data].

Red Color: Indicate date having recorded data

Blue Color: Indicate date that mouse clicks
Gray Color: indicate not having recorded data
MD ONLY Button: Load Motion Detected data only.
LOAD Button: Load data of selected date from calendar.

70

SmartDVR Formula Search Mode

Method of print current image

Click Button [Print] of SmartDVR Formula Search.

Print Channel: Select channel for printing images.

Option: Print image with Caption or select Print Option. Caption
indicates Channel number and recorded time, place is not be indicated.
Print Type: Setup Print layout.
Watermark Viewer ICON
Open saved .bmp file to check if there is any image tampering & check
if watermark is identical with original image.
Ref Watermark is the skill to prevent illegal-copy and to protect
effectively license and ownership of data owner. This digital watermark
does not interrupt to watch image and use s/w at all. Also, watermark
is very effect to find the source of original copy and the course of
reprint.
71

SmartDVR Formula Search Mode

Click SmartDVR Formula search's [WaterMark Viewer] button and

executes watermark viewer.
Click [file> Open] and call image which is stored to DVR System.
Ref (image must be .bmp file format)
Click WM Detect to check if the image has been tampered.
An image that has been tampered will illustrate an X in User
Defined Mark as shown below.

72

SmartDVR Formula Search Mode

Digital Zoom function

Digital Zoom is function that can expand specific part of image that is
revived in SmartDVR Formula Search.

Select clicking specific part of recorded image in SmartDVR

Formula Search.
If you roll mouse wheel, image is maximized up to x4 zoom.
(wheel mouse must be used).

73

SmartDVR FormulaAVI Backup Manager Mode

SmartDVR Formula AVI Backup Manager Mode

AVI Backup Manager converts the recorded data into AVI file format to
replay the
Image conveniently using Windows Media Player.
Click [AVI Backup Manager] from SmartDVR Formula Search Mode or
desktop.

Playback Control Panel

Channel Panel
AVI Convert Control Panel
Audio Volume Control Panel
Data Search Process Panel

74

SmartDVR FormulaAVI Backup Manager Mode

Playback Control Panel

Playback Button: Playback

Pause Button: Pause playing
Reverse Playback Button: playback reversely
2x Playback Button: Playback 2x speed.
4x Playback Button: Playback 4x speed
2x Reverse Playback Button: Playback reversly 2x speed.
Play Next frame Button: Playback frame by frame
Previous frame Reverse Button: Reverse Playback frame by frame
Playback Mode supports 4 channels or 1 channel viewing mode.
2

Channel Panel

Select channel you wish to convert into AVI File

using mouse. Click one more to cancel the
selection.

75

SmartDVR FormulaAVI Backup Manager Mode

AVI Convert Control Panel

Selected channel data is converted into AVI File.

Setup Backup Time: Setup backup time to AVI File. Click [A->B] icon
to setup start time and click one more to setup end time..
Convert into AVI File: AVI File backup starts
4

Audio Volume Control Panel

Control audio volume when playback of recorded data.

If various channels have recorded, only selected
channel can be replayed.
5

Data Search Process Panel

Hour Button: Recorded data of selected hours is indicated in red color.

Minute Bar: Minute of recorded data is indicated 0~59min and
recorded data is indicated in red color.
Search Mark Icon: It points the time on-searching.
Time: It indicates the time on-searching.

76

SmartDVR FormulaAVI Backup Manager Mode

Application
Backup to AVI File
Click [AVI Backup Manager] from SmartDVR Formula Search or
desktop to operate AVI Backup Manager.
Click [Load Data] icon then Calendar window
appears.
Select the date you wish to back up, and click
[LOAD] icon.
Select the channel you wish to back up in Channel
Icon. Channel icon turns green when selected.
Enter the time you wish to start backup from Time
Bar. Recorded data is indicated in red.

Click the start time and click [AB] icon. Then

start time will automatically appear.
Click the end time and click [AB] icon. Then
end time will automatically appear.
Click [Converting] icon after entering the limits of
the backup time in reference.
Start Backup to AVI File after selecting the
location of the directory to backup data and clicking
[OK].
Windows prompt message indicating AVI Converting End will
automatically appear. You have successfully converted your data
for storage.

77

SmartDVR FormulaAVI Backup Manager Mode

Ref The backup time converted by AVI Backup Manager is less than
one hour. Therefore, when the time between start and end is less than
one hour, backup data time indicates.
Play Backup Data using Windows Media-Player
AVI File which is backup with AVI Backup Manager use Intotech own
codec. Accordingly, if playing backup data in uninstalled DVR Software
computer, it requires installing Intotech own codec the first. Intotech
own Codec can be downloaded from (http://www.intotech.co.kr)
[DownloadUtility] for free, also our installation CD includes this codec

Notice Please Install Intotech own codec at the end. It may cause
problem to play if other codec is installed when Intotech codec has
already been installed in the PC.
AVI Replay all AVI format data using your Windows Media Player.
Media Player should replay stored data as seen below.

78

SmartDVR FormulaAVI Backup Manager Mode

79

SmartDVR Formula Backup Manager

SmartDVR Formula Backup Manager

Recorded images from SmartDVR Formula can be managed efficiently
or quickly backup to CD or Hard Disk.
REF CD Backup is supported in minimum Windows XP.

Data List
Control Panel
Backup List
Backup and Progress

80

SmartDVR Formula Backup Manager

1

Data List

Recorded data from DVR System indicates in the

order of [Record location>Record Date>Record
Channel>Record Time].
2

Control Panel

This panel can control backup data. Backup data can

be added or removed.
Transfer selected data from Data List to Backup
List.
Remove selected data in Backup.
Remove all selected data in Backup List.
Start [AVI Backup Manager].
Start [SmartDVR Formula Search].
Start or Stop to backup

Backup List

It lists backup data. Name of data

file will be formed into as follows,
please refer to when add or
remove data.
00 - 200501281533-0000.IVA
Ch Year/Mon/Date/Hour/Min File
No
Ref Channel will be marked as
00ch~15ch.

81

SmartDVR Formula Backup Manager

4

Backup and Progress

It indicates backup folder directory and backup progress.

Select folder to backup data.

If backup to CD, select CD-RW device and set up option. For more
information, please refer to 87page.
Indicates folder to backup data.
Indicates total size of backup List data.
Ref One CD can storage maximum 700MB, so when backup to CD,
need to check backup size.
Indicates free size of Hard Disk.
Indicates backup progress when click [Start Backup] to start
Application
Backup to HDD using Backup Manager
Click [Backup Manager] from SmarDVR Formula Search or desktop to
operate backup manager.
Select the date and time you wish to backup from Data List.
E.g. Indicates 2005/ 01/ 28/ CH 1 15oclock.
Click [>>] button and move selected
data to Backup List.
Check Backup Size and click [Select
Backup Folder] button and set up folder
to backup.
Click [Start Backup] button, then start
backup.
Ref Backup data is not able to
overwrite in DVR System, and then it is saved with occupied Hard
Disk storage. Therefore, the record time would be shorter.

82

SmartDVR Formula Backup Manager

Backup to CD using Backup Manager

Click [Backup Manager] from SmarDVR Formula Search or desktop to
operate backup manager..
Notice CD Backup can be supported in minimum Windows XP.
Select the date and time you wish to
backup from Data List.
E.g. Indicates 2005/ 01/ 28/ CH 1
15oclock.
Click [>>] button and move selected
data to Backup List.
Check backup size and click [CD
Backup] button.

From Select CD Backup Device(Picture ), select CD-R or CD-RW

device.
Check [Contain Backup Player] option.
Ref [Contain Backup Player] is an option for including Backup
Player when backup to CD. This is necessary for playing CD at the
other place. Therefore, we recommend checking [Contain Backup
Player]..
Click [Start Backup] button, then start backup.
Ref Error Message.
There is no medium in the burner
There is no CD inside CD-RW drive
If you want to Backup CD. Please reboot or end process
imapi.exe
Reboot PC or stop imap.exe by force from Windows Task
Manager.
Set CD recorder failed - Conflict with CD-RW settings
83

SmartDVR Formula Backup Manager

Not Enough HDD Disk Free Space to Create CD IMAGE
HDD must have enough free space to CD backup data onto
CD.
The call failed because IMAPI has not bean opened with Open.
Your Operating System (OS) does not support issues, please
contact your local Intotech DVR dealer.

84

SmartDVR Formula NetClient Mode

SmartDVR Formula NetClient Mode

NetClient Program is able to receive images from DVR Server using the
Internet. NetClient functions: Display & recording, camera control from
remote site and other features that we will illustrated in this document.

1 Control Panel

2 Screen Partition Panel

3 P/T/Z Control Panel

4 Channel Type Selection Panel

5 Other Panel

85

SmartDVR Formula NetClient Mode

Control Panel

The Control Panel can search program, open connection setup and
record server image from remote PC where NetClient is installed.

Search Button: Runs search program

Connection Setup Button:
Run [Connecting & Configuration Management] used for internet
access. Run [Modem Connection] used for internet access.
Remote Connection Setup Button:
Connect with DVR System and set up from remote site.
Recording Button: Save selected channels.
All Button: Select all channels to record.
2

Screen Partition Panel

Support 7 kinds of various screen partition, also

can establish function such as full-screen and
sequence rotation display mode.

86

SmartDVR Formula NetClient Mode

P/T/Z Control Panel

When DVR Server is using P/T/Z camera, select

channel you wish to control and click various
buttons from P/T/Z Control Panel to control camera.
Also, it enables to control play speed of image
using below drag panel.
Ref Only broadband Internet users [LAN Mode]
can use P/T/Z control.
Modem users [Modem Mode] cannot use this
feature
4

Channel Type Selection Panel

Click specific channel from Camera

Selection Panel to enlarge and view
image
5

Other Panel

Modem: Select [MODEM] when using Modem

LAN: [LAN] when using ADSL, VDSL, Cable, LAN etc. and network
speed is rapid
Record Image: Save one frame image from on-playing image.
Print: Print image from on-playing image.
Connection Setup for LAN Users
If users PC have already connected with LAN, it
will automatically setup LAN.
Click [LAN] icon from NetClient Main Screen to
connect from remote site using LAN.

87

SmartDVR Formula NetClient Mode

Connection Setup for Modem Users
Click [MODEM] icon from NetClient Main Screen to connect from
remote site using Modem. Click [Configuration]
button to run [Modem Connect] window
[[Modem Connect] window is initialized. Insert
Telephone No.(Insert the number assigned to DVR
Server. Insert w and Telephone No. to add the waiting time while
the line is being dialed.
E.g. (w0232851525), ID
& Password, (Insert the
ID & Password which is
registered in the Server
Program, [User
Management].) Select
the camera channel
number and click
[Connect].
Ref you can only access one channel at just one time using
Modem. In order to change into different channel, click
[Disconnect] and try to connect the other channel again.
Configuration
The modem model
name will appear
when you click
[Configuration].
During initial setup,
the Model Name
needs to be confirmed to complete registration, thereafter, this step
will be bypassed.
Click [Properties] to view General/Advanced default setup. Use
default when use of modem.

88

SmartDVR Formula NetClient Mode

DVR System Fixed IP Registration

If DVR System has fixed IP, it is able to connect with
DVR System directly.
Click [Configuration] from NetClient Main Screen.
Click [Fixed IP] Tap.

Insert Server Name and IP Address.

Users can make Server name.
Port is [20408] if default port has not changed.
Put an IP account which is registered to DVR System.
For information of Registration and Management, please refer to
45page.
89

SmartDVR Formula NetClient Mode

Register inserted DVR System to fixed IP List.
Registered DVR System content appears.
DVR System DHS Service Registration
If DVR System has Dynamic IP, DHS Service is
required to use
Click [Configuration] from NetClient Main Screen.
Click [Dynamic IP] Tap.

Insert DHS ID and Port.

DHS Service ID means specified ID which is registered to Intotech
DHS Service.
It is not related with DVR System accounts.
Port is [20408] if default port has not changed.
90

SmartDVR Formula NetClient Mode

Put an IP account which is registered to DVR System.
Register inserted DVR System to fixed IP list.
Ref Summary of DHS Service

All computers have their own addresses and we call them IP. Our
SmartDVR Formula supports remote control by using IP of Internet. On
the same principle as mail delivery after sorting according to address in
Post Office, many computers are able to communicate through IP
address using Internet. Using this feature of Internet, our SmartDVR
Formular supports various network function for search and setup
configuration from remote site etc.
There is a problem that IP can changeable. Due to short of IP address
worldwide, most of all telecommunication companies use procedure
that sharing IP address with many computer in order of connection.
Therefore it is highly possible that computer IP address change every
time they connect Internet. If IP address changes, we can lose the
address to contact DVR System..
DHS Service is the one System to overcome this Internet environment.
DHS is checking the IP per 10 minutes to maintain the remote control
regardless of DVR System IP Changing. Even though remote users
dont know DVR System IP address, they can connect with DVR
System using DHS Service which is like mediating between remote
users and DVR System. So they can use network functions from any
where without any interference by changing IP address. This is DVR
Network Service, Intotechs own great power.
91

SmartDVR Formula NetClient Mode

Connecting & configuration Management

Connect Management
Set up each channel to connect.
Connect Button
Click [Connect] button to connect with each channel
[Server Name] indicates registered DVR Systems to Fixed IP /
Dynamic IP.
All Connect Button
Connect all channels of DVR System.
Information
Indicates information of selected DVR System.
Indicates statues of connection.

92

SmartDVR Formula NetClient Mode

Management of group
Group Connection enables users to connect to various DVR Systems
with one click.

Group List
Indicates registered group list.
Server List
Lists registered DVR System to Fixed IP / Dynamic IP Tap.
Channel
It indicates channels which are able to connect with selected DVR
System from Server List. Users can set up directly.
Add server in Group.
Add selected channel from server in selected group.

93

SmartDVR Formula NetClient Mode

Advanced

Store Disk List

Check () HDD to use as recording device
Notice If data is recorded on HDD (Operating System installed), it
may cause unstable status by lack of store space. Recommend to
disable C drive (Operating System installed) as recording device
and use other drives (D, E).
Overwrite
Setup overwrites to delete the oldest data when free HDD is lesser
than minimum free space allowed.

94

SmartDVR Formula NetClient Mode

Screen Mode
Dual Monitor: Setup this option when use of Dual Monitor function
supported from some graphic card.
YUV/RGB: Setup YUV or RGB. YUB Mode is fewer loads than
RGB Mode. If you are not able to view the images using YUV
Mode, update the Graphics Card Driver and if problem persists
check whether the Graphics Card supports YUV Mode.
Transmission Mode

Setup Image Quality transmitted from DVR Server.

Network transmission speed will be decreased as you increase the
image quality due to file size.

95

SmartDVR Formula NetClient Mode

Transmit Mode
Remote Mode: Setup when use of NetClient from external network.
Frame is decreased to improve transmission speed.
Local Mode: Setup when use of NetClient from internal network.
Image is displayed regardless of frame speed.
Application
Record image from NetClient
It enables to record images from NetClient PC during surveillance.
Log in DVR System you wish to surveillance.
Click mouse left button on the screen you wish to
record and click REC button to record.
Record captured image from NetClient
It enables to save captured images as JPEG File from NetClient
PC during surveillance.
However, WaterMark cannot be supported.
Connect with DVR System you wish to surveillance.
Select the image you wish to save with mouse left
button and click [Save] Icon.
From [Record File] window, select directory to save and
click [Save] button.
Print captured image from NetClient
It enables to print captured images during surveillance from
NetClient PC. Max 8ch print is available.
Connect with DVR System you wish to surveillance.
Select the image you wish to print with mouse left
button and click [print] Icon
Setup print shape and channel, click [Print] button.

96

SmartDVR Formula NetClient Mode

Local Search

Control Panel
Playback Control Panel
Screen Partition Panel
Search Data Process Panel

97

SmartDVR Formula NetClient Mode

Control Panel

Consist of [Surveillance Mode] icon, [Load Data] icon, [Save Still

Image] icon, [Print Still Image], [WaterMark Viewer] icon.

Surveillance Mode Button: Converts to Surveillance Mode.

Load Data Button: Shows recorded date in calendar.
Save Button: Save captured image as Bitmap File.
Print Button: Print captured image using printer.
WaterMark Viewer Button: Runs WaterMark Viewer.
2

Playback Control Panel

Playback Button: Playback

Pause Button: Pause playing
Reverse Playback Button: playback reversely
2x Playback Button: Playback 2x speed.
4x Playback Button: Playback 4x speed
2x Reverse Playback Button: Playback reversly 2x speed.
Play Next frame Button: Playback frame by frame
Previous frame Reverse Button: Reverse Playback frame by frame
Playback Mode supports 4 channels or 1 channel viewing mode.
98

SmartDVR Formula NetClient Mode

3

Screen Partition Panel

Support 8 kinds of various screen partitions,
full screen and sequence rotation display
mode etc.

Search Data Process Panel

Hour Button: Recorded data of selected hours is indicated in red color.

Minute Bar: Minute of recorded data is indicated 0~59min and
recorded data is indicated in red color.
Search Mark Icon: Points the time on-searching.
Time: It indicates the time on-searching.
Search Data
Click [Load Data] icon from NetClient Search.

Red Color: Indicates that there is recorded data.

99

SmartDVR Formula NetClient Mode

Blue Color: Indicates date that mouse click.
Grey Color: Indicates that there are no data.
MD ONLY Button: Search only motion record data.
LOAD Button: Load recorded data from selected date.
Remote Search
Remote Search using LAN

Click [Search] icon from NetClient.

Click [Remote search] from NetClient Main
Screen

Select DVR System you wish to connect from [Remote Search]

window.
IP and Port will be setup automatically as registered as to
[Configuration>Fixed IP & Dynamic IP].
Insert ID and Password.
Select channel you wish to connect. Max 4ch search & playback is
available from remote site using LAN.
Click [Connect] button.
If connects properly, indicates the date in red which is recorded in
DVR System.

100

SmartDVR Formula NetClient Mode

Select the date you wish to search from the above calendar and
click [Load Data] button.

Click hour button in red to load data. The loading time depends on the
bandwidth. It takes 30sec to max 1min
Remote search using Modem
Click search icon from NetClient.
Click [Remote Search] from NetClient Main
Screen.

Insert Phone No. from [Remote Search] window.

Insert ID and Password.
Select channel you wish to connect. Only 1ch search & playback is
available from remote site using Modem.
Click [Connect] button.
If connects properly, indicates date which is recorded in DVR System.
Select date you wish to search from the above calendar and click
[Load Data] button. The loading time depends on the bandwidth.

101

SmartDVR Formula NetClient Mode

Remote Search Main Screen

Remote Search Main Screen is the most same both LAN Mode and
Modem Mode.
(Only1ch search & playback is available from remote site using Modem

Control Panel
Playback Control Panel
Screen Partition Panel
Search Data Process Panel

102

SmartDVR Formula NetClient Mode

1

Control Panel

Surveillance mode Button: Converts to surveillance mode of

NetClient
Local search Button: Search recorded images at NetClient system.
Remote search Button: Search recorded images at DVR System
Save Button: Save images of present selected channel as BMP
Watermarking function is not available.
2

Playback control Panel

Pause/Playback Button: Supports pause and playback of

images.
Ref In remote search, 2X, frame by frame playback does not
supported.
Playback speed control: Controls playback speed.
3

Screen partition panel

Supports various screen partition.
Ref In remote search, Only 1ch & 4ch
screen partition is supported.

103

SmartDVR Formula NetClient Mode

4

Data search process Panel

Hour Button: Recorded data of selected hour is indicated in red color.

Minutes search bar: Minute of recorded data is indicated 0 ~ 59min.
Recorded data is indicated in red color.
Present search time icon: It indicates time to search at present.
Remote configuration
When you click [Remote configuration]
button at main screen of NetClient,
[Remote setting] windows appears.
Click [Connection] button after inserting
information of server system to connect

104

SmartDVR Formula NetClient Mode

Remote configuration>General

Start Section
Auto start : DVR program is automatically executed when systems
is turned on.
Max size at starting
DVR program is setup as the exact size of monitor resolution to
prevent display of other program..
Exit
Only DVR program shuts down after closing DVR program or the
complete systems shuts down. (Computer power off).
Video / Audio setup
Setup camera input type (NTSC/PAL)
NTSC: Korea, USA, Japan, Australia (some region), North America
(some region) etc
PAL: NTSC Regions excluding NTSC area (China, Europe, South
America, etc)

105

SmartDVR Formula NetClient Mode

Channel selection
Select channel for surveillance. Generally, be off channel not to
connected to camera.
Resolution setup
Setup resolution of image. There are low resolution and high
resolution.
Ref NTSC 320X240, 640X480
PAL 360X288, 720X576
Remote configuration>Store

Store disk
Indicates installed HDD drive to record (removal HDD is not
indicated)
(Check () HDD to use as recording device)
Notice In case of picture is stored in hard-disk which has operating
system, if hard-disk will be full, system can be shut down or repeat
rebooting.
106

SmartDVR Formula NetClient Mode

Disk information
Indicates information of HDD selected in store disk.
Overwrite
Setup overwrite to delete the oldest data and record new data
when free HDD is lesser than minimum free space (default: 1024
MB) allow.
Notice In case of using Overwrite function, the oldest data will be
deleted without any warning notice about lack of disk capacity.
It is important to store important recorded data after backup
through [Backup Manager] program.
Record setup
It supports record or non-record per channel.
Remote configuration>Network

It displays network configuration status of server system.

Ref Change of configuration is not available.
107

SmartDVR Formula NetClient Mode

Remote configuration> Maintenance

Windows information
It displays information Windows and system of DVR System
DVR version information
It displays board model and version of DVR System.
System maintain
When SmartDVR Formula starts, it checks file and image data of
DVR System
Normal Check Mode: This check for video data index and
program files.
Full Check Mode: System integrity is added from the normal
check mode so the duration time can be slow.
System auto reboot
It setup specific time to automatically reboot system for checking
system maintenance or Windows stability.

108

SmartDVR Formula NetClient Mode

Remote configuration>Event

Sensor input
Check [Enable the sensors] and configure the channel of camera
and sensor input channel.
Ref Sensor type
NO (Normal Open)
Switch of NO type sensor is usually opened. When motion is
detected, sensor works by closure of switch. There does not
need to configuration at this configuration..
NC ( Normal Close)
Switch of NC type sensor is usually closed. When motion is
detected, senor works by open of switch. When you use NC
type sensor, click [NC] button below sensor number.
Action
When sensor is triggered, it supports operation of DVR
automatically.
109

SmartDVR Formula NetClient Mode

Enable event recording
When sensor is triggered, images of selected channel are
recorded by [duration time: establish in ].
Enable the warning sound
When sensor is triggered, sound of selected wave file rings which
is established in ]
Send e-mail at detection
When sensor is triggered, detected image is transferred to e-mail
address which configured at [Configuration>E-mail] in DVR server
system.
Enable the digital output
When sensor is detected, various output device such as warning
light, siren, warning speaker works.
Remote configuration>E-mail

110

SmartDVR Formula NetClient Mode

Mail server
Input IP address at of sender.
Ref Although E-mail function supports almost all mailing service,
some mailing service is not available for E-mail function.
Sender
Input name and e-mail address of sender.
Message recipients
To: Input e-mail address of recipient.
CC: Input e-mail address of other recipient
BCC: Input e-mail address for Blind Carbon Copy.
E-mail time setup
Setup email response time after sensor has been triggered

111

SmartDVR Formula WebClient Mode

SmartDVR Formula WebClient Mode

WebClient can receive the images from remote site & view through the
internet without installing any other program.

Display mode
There are two modes available: [YUV Mode]
& [RGB Mode].
Ref If you are not able to view the images
using [YUV Mode], update Graphics card
driver and if problem persists, check whether the Graphics card
supports [YUV Mode] and if not , select [RGB Mode].

112

SmartDVR Formula WebClient Mode

Screen Mode (Ch Split)

There are 7 variation of screen partitioning
that is supported according to camera number

.
3

P/T/Z Control panel

When you use P/T/Z camera at remote site,
select channel to monitor. You are able to
control P/T/Z function clicking each P/T/Z
button. When you control drag bar at below of
control panel, you are able to setup play
speed of image.

Connection

All connect: It is available to connect all channel at one time.

If you wish to specific channel from server, you click channel you want
to view.
Connection to DVR systems (Static IP)
Insert the Server IP address in
Internet Web browser.
E.g.

Insert
http://61.107.32.82:26540 if
the server IP address is
61.107.32.182.

113

SmartDVR Formula WebClient Mode

Message as above will appear if this is your first time connecting

through Internet Web browser. Click [Yes] button and it will take a few
seconds to load the WebClient program.

When [Log-in] windows executes, insert ID and Password setup at

server and click [Connect] butt.

114

SmartDVR Formula WebClient Mode

Connection to DVR system which is registered DHS Service

Click [Log in] button after inserting DHS ID at [ID]. DHS ID has to be as
same as used at registration of DHS service.
REF Message as above will appear if this is your first time connecting
through Internet Web browser. Click [Yes] button and it will take a few
seconds to load the WebClient program.
After program is installed, IP and port is
inserted automatically. Insert ID and
Password at [Log in] and [Connect] button.
ID and Password is as same as used at
registration of DHS service.

115

Compatible / Incompatible

Compatible / Incompatible
SmartDVR Formula System Specification
Minimum Spec
Select
S
H
HP

Recommendation Spec

CPU

RAM

CPU

RAM

1.7Ghz or
higher
1.7Ghz or
higher
2.4Ghz or
higher

128 MB
or higher
256 MB
or higher
512 MB
or higher

1.7Ghz or
higher
2.4Ghz or
higher
2.4Ghz or
higher

256 MB or
higher
512 MB or
higher
512 MB or
higher

SmartDVR Formula
Compatible

CPU

Mother
board

Intel Pentium Process

(x86, 1.7Ghz Over)
- Intel Celeron 1.7Ghz or
Higher
- Intel Pentium IV
- AMD Athlon XP
With one or more PCI slot,
supporting Intel Pentium
processor
- Intel 81x Chipset
- Intel 84x Chipset
- Intel 85x Chipset
- Intel 86x Chipset
- VIA KM400
<Mother board name>
- Chaintech CT-9LIF3
- Chaintech CT-9LIF7
- Chaintech CT-9EJL2 SE
- Chaintech M845GV
- Albatron PX865PE Pro
- GigaByte GA-8GE800Pro
- GigaByte GA-8GEM667
- Gigabyte GA-8IG1000MK

Incompatible
Lower than Intel Pentium
1.7Ghz Process
- Other than x86

Intel CPU/ Via Chipset

(694x & 694tx Seriesetc)
Intel CPU/ SIS Chipset
- Gigabyte 81845GVM-RZ
(Intel 845 Chipset)
- Cyrix C3 Motherboard
- MSI Neo2
(Intel 865 Chipset)

116

Compatible / Incompatible
- ASUS P4P800

VGA
(Graphi
c Card)

Sound
Card

HDD

OS

With 16MB or higher

memory, Supporting 32Bit
Color and YUY2 DirectX
Mode
- ATI Expert 2000 32MB
SDRAM
- ATI Radeon Series
- nVidia Riva TNT2 Series
- nVidia Geforce Series
- Intel 845G/GL Graphics
controller(OnBoard)
- Intel 865G Graphics
controller(Onboard)

- Intel 81x Graphics

Controller (On Board) or
Intel i740
- VIA Chipset Onboard
Graphic Controller
- SIS Chipset Onboard
Graphic Controoler
- GeForce 4 MX440 AGP8X
- ATI Radeon 7000, 9600

Intel CPU/ Via Chipset

Board
- Gigabyte 81845GVM-RZ
(Intel 845 Chipset)
HDD 5400RPM or higher
Windows XP(Professional,
Home)
Windows 2000
Series=(Real Display DVR
driver must be installed
manually)

Windows 98 Series
Windows ME
Mac OS
OS/2

117

Compatible / Incompatible
NetClient
Compatible
CPU
Motherb
oard

VGA
(Graphi
c Card)

Sound

Incompatible

All CPU Compatible

All Motherboard compatible
excluding the noncompatible part

SiS, Via chipset

motherboard

All Graphic Card compatible

excluding the noncompatible part

-When use of Onboard SiS

or Via chipset motherboard
- SiS, Via chipset
motherboard

Card

All PCI slot and Onboard

type

HDD

All 5400RPM or higher HDD

OS

Windows XP
recommend(Professional,
Home)
Windows 2000 Series
Windows 98 Series
Windows ME
* Direct x8.0 or higher is
necessary

Mac OS, OS/2

118