B.

Pharmacy 3rd Year

Pharmaceutical Engineering
Q: Explain About centrifugal mill.
A: Centrifugal Mill.
Fine grinding made easy:
No screens cleaning made easy controllable results
OVERVIEW
Ideal for:

Fine grinding of friable materials

Coarse grinding friable materials
De-agglomerating
Conditioning of cellulose fibers
Tight particle size control

Finally, a mill that gives controllable particle size distribution and is easy to clean. The versatile Centrifugal Impact Mill provides a simple,
inexpensive means of grinding, sizing, de-agglomerating and homogenizing material, and can be employed as an effective infestation destroyer. It
yields particle sizes down to 325 mesh and is primarily used for friable materials. Available in #304 stainless steel, sanitary, abrasive resistant and
standard carbon steel design, the Centrifugal Impact Mill operates without screens, hammers, knives or rolls.
OPERATION
Metered material is gravity fed through the centrally located inlet of the "stator disc". Centrifugal forces accelerate the material and launch it into the
impact zone. The action created by the stationary and rotating pins creates a "treacherous path" for material to pass through. Achieving the desired
tight particle size distribution is obtained by controlling the rotor speed. Varying the rotor speed between a few hundred rpm up to 5400 rpm provides
the flexibility to use the machine as a coarse grinding or de-agglomerating unit as well as a fine grinding mill. Whether the machine is used for
cracking wheat, grinding iron oxide powder, creating powdered sugar or as a cellulose fiber conditioner, large production throughput rates can be
attained in an inexpensive, compact machine. It also fits in neatly after most flaking operations.
Vertical orientation of the Centrifugal Impact Mill housing allows the outer disc to hinge open for rapid cleaning and inspection of all productcontact surfaces

CENTRIFUGAL MILL
The Centrifugal Mill is a high speed rotor mill with unmatched performance. It is used for the rapid size reduction of soft to medium-hard and
fibrous
materials.
Because of the efficient size reduction technique this mill ensures the gentle preparation of analytical samples in a very short time. The
comprehensive range of accessories including a large variety of ring sieves and rotors as well as collection systems makes the Centrifugal Mill a
versatile instrument that can be easily adapted to varying applications. The optional Vibratory Feeder is load-controlled via an interface and ensures
a uniform grind at maximum output rate. When using a cyclone, the sample material is additionally cooled by the air stream and more rapidly
discharged from the grinding chamber via the cassette pan with outlet. This effect can be increased by connecting a vacuum cleaner.

APPLICATION EXAMPLES
activated charcoal, animal tissue, bentonite, bones, cereals, chemical products, coal, coffee beans, coke, collagen, corn, dried fruit and vegetables,
dried larvae, drugs, electronic components, feed pellets, fertilizers, food, limestone, minerals, paper, pharmaceutical materials, plant materials,
plastics, powder coatings, refuse derived fuels, rice, rubber granulate, seeds, spices, straw, ...

PRODUCT ADVANTAGES

Powerdrive with optimally matched frequency converter and 3-phase motor

comfortable parameter setting via display and ergonomic 1-button operation
wide range of accessories including various collection and feeding systems, rotors and sieves
gentle and very rapid size reduction by pre- and fine grinding in one run
wide speed range
patented cassette system for maximum sample recovery and easy cleaning
easily exchangeable grinding and sieve inserts
defined final fineness due to ring sieves sieves with aperture sizes from 0.08 - 10 mm
comfortable safety housing with automatic cover closure

motor compartment and electronics protected against dust and material penetration

Features
Applications
Field of application
Feed material
Size reduction principle
Material feed size*
Final fineness*
Batch size / feed quantity*

Speed at 50 Hz (60 Hz)

Rotor peripheral speed
Rotor diameter
Types of rotors
Material of grinding tools
Sieve sizes
Setting of grinding time
Collector capacity

Drive
Electrical supply data
Power connection
Protection code
Power consumption
W x H x D closed
Net weight
Documentation

fine grinding
agriculture, biology, chemistry / plastics, construction materials, engineering / electronics,
environment / recycling, food, geology / metallurgy, medicine / pharmaceuticals
soft, medium-hard, brittle, fibrous
impact, shearing
< 10 mm
< 40 m
300
ml
with
standard
cassette
20
ml
with
mini-cassette
1000
ml
with
paper
filter
bag
4500 ml / 2500 ml / 450 ml / 230 ml with cyclone
6,000 - 18,000 min-1, free selectable
31 - 93 m/s
99 mm
6-tooth rotor / 12-tooth rotor / 24-tooth rotor / 8-tooth mini-rotor
stainless steel, titanium, steel 1.4404, stainless steel with wear-resistant coating
trapezoid holes 0.08 / 0.12 / 0.20 / 0.25 / 0.50 / 0.75 / 1.00 / 1.50 / 2.00 mm
round holes 3.00 / 4.00 / 5.00 / 6.00 / 10.00 mm
900
ml
with
standard
cassette
50
ml
with
mini-cassette
3000
ml
with
paper
filter
bag
5000 ml / 3000 ml / 500 ml / 250 ml with cyclone
3-phase asynchronous motor with frequency converter
different voltages
1-phase
IP 20
1300 W
410 x 515 x 365 mm
~ 38 kg
Operation & Application Video

Standards
*depending
on feed
configuration/settings
WORKING

CE
material

and

instrument

In the Centrifugal size reduction takes place by impact and shearing effects between the rotor and the fixed ring sieve. The feed material passes
through the hopper (with splash-back protection) onto the rotor. Centrifugal acceleration throws it outward with great energy and it is precrushed on
impact with the wedge-shaped rotor teeth moving at a high speed. It is then finely ground between the rotor and the ring sieve.
This 2-step grinding ensures particularly gentle but fast processing. The feed material only remains in the grinding chamber for a very short time,
which means that the characteristic features of the sample to be determined are not altered. The ground sample is collected in the collecting cassette
surrounding the grinding chamber or in the downstream cyclone or paper filter bag.
Diag :- Spare parts of a Centrifugal mill.

Q2: What are azeotropic mixtures.

A:Azeotropic mixtures- Many liquids cannot be separated into two pure components by simple distillation, because the volatilities of the
components are equal. Such a mixture is known as an azeotrope (Greek: boil unchanged).So therefore azeotropic solution is a solution which distils
unchanged at a constant temperature. Such solutions are also known as constant boiling mixtures.
Minimum boiling point azeotropic solutions-Type II solutions (non-ideal solutions): A system with maximum vapour pressure or minimum boiling
point is known as azeotropic mixture. For e.g. chloroform and acetone, pyridine and acetic acid. The azeotropic mixture has a lower boiling point
than that of component with the least boiling point. At the minimum boiling point temperature, the liquid composition remains constant and is equal to
the vapour composition (arising from such a liquid system).
Consider a hypothetical case in which the mixture contains more of D than C, which is represented by M. if the mixture is distilled, the vapour has a
composition of x. when this vapour is condensed, the liquid composition is represented by M1, which is richer in D than C. when liquid is redistilled,
the vpour has composition of x1. When this vapour is condensed, the liquid has the composition of M2. Thus on repeated distillation, the liquid D will
be in pure form and remains in still. Similar arguments can be proposed for fractional distillation of component C by considering left side curves to
trough.

Maximum boiling point azeotropic solutions- Type III solutions (non-ideal solutions): A system with minimum vapour pressure or maximum boiling
point is known as azeotropic mixture. For e.g.- benzene and ethanol, water and ethanol. The azeotropic mixture has a higher boiling point. At the
maximum boiling point temperature, the liquid composition remains constant and is equal to the vapour composition (arising from such a liquid
system).
Consider a hypothetical case in which the mixture contains more of A than B, which is represented by L. if the mixture is distilled, the composition of
vapour v is richer in A and poorer in B. At this state, the liquid residue in the distillation flask will be richer in B and poorer in A. the vapour at v is
condensed, the liquid composition is represented by L1. If this liquid is distilled, the composition of vapour v1 is further richer in A and poorer in B.
thus on repeated distillations, the liquid A in pure form can be obtained as a distillate. But the residue the remained in the still is always the mixture of
A and B of constant composition. Similar arguments can be proposed for fractional distillation of component B by considering left side curves to P.
NOTEFOR DIAGRAMS, ,PLEASE REFER SUBRAMANYAM PAGE NO.313 & 315.FIRST EDITION
Q:3. EXPLAIN CORROSION AND ITS PREVENTION.
A: CORROSION AND ITS PREVENTION
Corrosion is defined as the reaction of a metallic material with its and can result in a functional failure of metallic component or of a complete
system.
Exposure of a surface to air, water and caustic chemicals are responsible for corrosion. Since metals are good conductors, they undergo
electrochemical changes on their surfaces. The compound that is formed during corrosion is referred to as corrosion product and the metal is referred
to as corroded. The corrosion media are generally liquid (mostly aqueous solution), but also solids and gases.
Corrosion can be either dry or wet type:
Dry corrosion: it involves the direct attack of dry gases (air and oxygen) on the metals through chemical reactions. As a result an oxide layer is
formed over the surface. This type of corrosion is not common.
Wet corrosion: it involves the direct attack of aqueous media (strong or dilute, acidic or alkaline) on metal through electrochemical reactions. The
moisture and oxygen are also responsible. This type of corrosion is quite common.
Application:
Knowledge of corrosion is helpful in certain areas to prevent problems.
Dies and punches: In the compression of tablets, dies and punches should be free from rust and corrosion. Use of chromium plated dies can
avoid this problem.
Milling equipment: In these equipment, a perfect fit between the moving parts should be maintained for effective size reduction. Thus due to
corrosion surface imperfections, do not facilitate proper cleaning of the equipment.
Chemical processing reactors: Diverse nature of solutions which come in contact with the reactor surface often lead to corrosion on account of
corrosive media and environment conditions.

 Fermenters: During fermentation, the release of trace metals from the equipment may have deleterious effects on the enzyme system and
metabolic pathways of the organisms. The possible corrosion aspects in the fermentors are pits and cervices, which make it difficult to clean
and remove the contamination. Maintenance of hygiene, need for sterility and prevention of contamination are important considerations in the
construction of fermenters.
Storage conditions: Prolonged storage of reactive chemicals lead to corrosion of fermnters.
THEORIES OF CORROSION
The metal surface undergoes an electrochemical reaction with moisture and moisture and in the atmosphere. This theory is known as electrochemical
theory of corrosion. The mechanism involves the formation of a galvanic cell (anodic and cathodic areas), by different metals (for example, Fe and
Cu) or in different areas on the same piece of metal (for example, iron).
1) Corrosion Reactions on Single metal
Electrochemical reactions can illustrated by considering the corrosion on a piece of iron, owing to surface imperfections (localized stresses, grain
orientation, inclusions in the metals) or
due to variations in the environment. Numerous tiny reactions may occur.
(For diagram refer-Pharmaceutical Engineering by C.V.S. Subramanyam; First edition; Published by-Vallabh Prakashan; page no.-433; figure 16.1)
Reaction at anode: Oxidation takes place with the release of electrons. Positively charged iron atoms get dethatched from the solid surface and
enter into solution (electrolyte) as positive ions.
At anode: Fe Fe ++ + 2e- (indicated by rough surface)
The released free electrons (negative charge) pass round the external circuit
Reaction at cathode: reduction of constituents occurs with the taking up of electrons. The fee electrons reach the cathode and react with some
positively charged species such as hydrogen ions in the electrolyte solution. In the absence of acid, water itself dissociates to generate H+ ions.
At cathode: 2H+ + 2e- H2 (indicated by formation of bubbles at the surface)
The amount of metal (iron) which is dissolved in the electrolyte is proportional to the number of electrons flowing, which in turn is dependent upon
the potential and resistance of the metal.
The overall reaction: Fe + 2H2O Fe(OH)2
+ H2
Red brown rust
High evolution of H2 accompanies rapid corrosion such as hydrogen embrittlement. Depletion of hydrogen al enhances corrosion. In moderate
concentrations of H2, corrosion slows down.
2) Corrosion Reactions between Metals
Galvanic corrosion results from the flow of current from a more active metal (anode) to less active metal (cathode). For example, Zinc dissolves and
forms an anode, while Copper (Cu) forms the cathode. These two metal form two electrodes and their presence in and electrolytic solution form a
Galvanic cell.
(For diagram refer-Pharmaceutical Engineering by C.V.S. Subramanyam; First edition; Published by-Vallabh Prakashan; page no.-434; figure 16.2)

Spontaneous reaction can occur when two electrodes are connected through an external wire.

Reactions at anode and cathode are:

At anode: Zn Zn++ + 2e- (indicated by rough surface)
(Oxidation)
At cathode: 2H+ + 2e- H2
(Reduction)

(indicated by formation of bubbles at the surface)

The corrosion current flows at the expose of anode metal, which get corroded continuously, whereas the cathode metal is protected.

FACTORS INFLUENCING CORROSION

A number processing factors affect rate of corrosion.
Solution pH
The pH affects the rate of corrosion of metals by one of the 3 general patterns.
1) Metals such as iron dissolve rapidly in acidic solution. In the middle pH range (4 to 10), the concentration of H + ions is low. Hence the
corrosion rate is controlled by the rate of transport of oxidizer (oxygen).
2) Certain amphoteric metals dissolve rapidly in either acidic or basic solution. Examples are aluminium and zinc. Corrosion proceeds.
3) Noble metals are affected by pH. Examples are gold and platinum.
The H+ ions have a tendency to take up electrons to form H2 gas. Therefore, H+ ions capture electrons and promote anodic corrosion.
Oxidizing agents
Oxidizing agents may accelerate the corrosion of one class of materials, whereas retard another class. Oxidizing agents such as oxygen (O2)
react with hydrogen to form water. Once hydrogen is removed, corrosion is accelerated. For example, copper in sodium chloride solution
follows this mechanism.
Oxidizing agents retard corrosion due to formation of surface oxides films, which makes the surface more resistant to chemical attack.
Therefore, adsorbed oxygen layer is essential. Thus a balance between power of oxidizing compounds to preserve the protective film and their
tendency to destroy the protective film determine the corrosion of the metal.

Temperature

The rate of corrosion tends to increase with rising temperature. It has a secondary effect. The influence of temperature on corrosion may
follow several mechanisms.
1) Increase in temperature reduces the solubility of oxygen or air. The released oxygen enhances the corrosion.
2) Increase in temperature induces phase changes, which enhances the rate of corrosion. At high temperatures, organic chemicals are
saturated with water. As the temperature decreases, water gas condensed.
3) Oxygen is needed for maintaining iron oxide film, which prevents corrosion. In the absence of oxygen (due to increase in temperature), the
corrosion of stainless steel increases.
4) Copper- based alloys do not depend on the film of corrosion.
Velocity
When the corrosive medium moves at a high velocity along the metallic surface, the rate of corrosion frequently increases. High velocity has
the following effects.
1) Corrosion products are formed rapidly, because chemicals (including oxidizing substances) are brought to the corroding surfaces at high
rate.
2) The accumulation of insoluble film on the metallic surface is prevented. Therefore, corrosion of these films decreases.
3) The corrosion products (or film) are easily stifled are carried away, thereby exposing the new surfaces for corrosion.
Thus corrosion proceeds unhindered. This factor is responsible for the corrosion of a number of equipment parts, such as condensers,
evaporator pipes, propellers, agitators and centrifugal pumps.
Surface films
Once corrosion is started, its further progress is often controlled by the nature of surface films. A variety of surface films have been observed.
Thin oxide films are formed on the surface of stainless steel (rusting).These films tend to retain or absorb moisture, which delays the time of
drying. Hence, the surface exposure to atmosphere or corrosive vapour increases the extent of corrosion. The rust films formed on low alloy
steels are more protective than those formed on unalloyed steel.
Insoluble salts such as carbonates and sulphates may be precipitated from hot solution on the metal surfaces. These protect the metal surface.
If the film is porous (example is Zinc Oxide), corrosion continues .Nonporous films (example is Chromium Oxide film on iron) prevent further
corrosion.
Oil and grease films may occur on the surfaces either intentionally or naturally. These films protect the surface from direct contact with
corrosive substances. Examples are metals submerged in sewage or equipment used for processing oily substances.

Other factors
The concentration of corrosive chemicals in the environment influences the rate of corrosion. In addition, corrosion rates are seldom linear over a
wide range. Concentration is important during plant shut-down. The presence of moisture that collects during cooling can turn innocuous
chemicals into dangerous corrosives.

TYPES OF CORROSION

Pure metals and their alloys tend to enter into chemical union with the components of corrosive medium to form compounds. Corrosion can be
broadly classified as follows:
1.
2.
3.
4.

Fluid corrosion, General

Fluid corrosion, Localized
Fluid corrosion, structural
Fluid corrosion, biological

Fluid corrosion: General

When corrosion is generally confined to a metal surface, its known as general corrosion. This type occurs in a uniform fashion over the entire
exposed surface area at a wide range of temperatures. General corrosion is of two types:
Physicochemical Corrosion: the effects of this type are swelling, cracking, crazing, softening etc. Examples are plastic and nonmetallic material.
Electrochemical Corrosion: this type of corrosion occurs at discrete points of metallic surfaces when electricity flows from cathodic area to anodic
area. Metallic surface gets divided into anodic portion or cathodic portion.
Fluid corrosion: Localized
Fluid corrosion is most frequently observed on different locations in a material. It occurs in numerous ways. It can be further classified as:
Specific site corrosion: Mechanically weak spots or dead spots in a reaction vessel cause specific site corrosion. It can be further classsified as Inter-granular corrosion: Selective corrosion tha occurs in grain boundaries in a metal\alloy is called intergranular corrosion.
Pitting corrosion: This type of corrosion results in development of pits and cavities. They range from deep cavities to shallow dipression.
Cervice corrosion: In this type, corrosion occurs in cervices because solutions are retained at such places, which takes longer time to dry out.
Stress induced corrosion: Residual internal stress in the metal or external applied stress accelerates the corrosion. It can be further classsified as Stress corrosion cracking: At the surface, if the tensile strength is equal to or more than the yield stress, the surface develops cracks. This is
known as stress corrosion crackin.
Corrosion fatigue: Corrosion fatigue is the ability of the metal surface to wihtstand repeated cycles of corrosion. As this process continues, the
surface looses its fatigue resistance and ultimate failure of equipment.
Fretting corrosion: it occurs when matal slide over each other and cause mechanical damage to one or both.
Flow related corrosion: Liquid metals can cause corrosion. Usually the driving force is the tedency of the liquid to dissolve solids or penetrating
the metal along the grain boundaries at places of wetting. It can be further classsified as Impingement corrosion: It is also known as erosion-corrosion or velocity accelerated corrosion. It is accelerated by removal of corrosive
products (such as oxide films), which would otherwise tend to stifle the corrosion reaction.
Erosion: Erosion is the destruction caused by the flow of liquid/gas (with or without suspende solids).
Cavitation erosion: Formation of transient voids or vaccums bubbles in a liquid stream pasasing over a surface is known as cavitation.

 Chemical reaction related corrosion: Corrosion involves chemical reaction such as oxidation and reduction at anode nd cathode, respectively. It
can be further classsified as Galvanic corrosion: It is associated with the flow of a less-active metal (copper cathode) from a more reactive metal (zinc anode) in the same
environment.
Oxygen concentration cell: This type of corrosion is due to the presence of oxygen electrolytic cell, i.e., a difference in amount of oxygen in
solution at one point exist when compared to another.
Hydrogen embrittlement: hydrogen can penetrate carbon steel and reacts with carbon to form methane. The removal of carbon results in
decreased strength.
Fluid corrosion: Structural
In the structural fluid corrosion type, the structural (mechanical) strength is reduced on account of corrosion. This may occur when one component o f
alloy is removed or released into the solution. Some examples are:
Graphite corrosion: Graphite is an allotropy of carbon and occurs in gray cast iron. The metallic iron is converted into corrosive products leaving a
residue of intact graphite mixed with iron corrosive products an other insoluble constituens of cast iron.
Dezincification: This type of corrosion is sen in brass that contains more than 15% zinc. In brass, the principal product of corosion is metallic copper,
which may redeposit on the plant. Another mechanism involves the formation of zinc corrosion products leaving the copper residue.

Fluid corrosion: Biological

The metabolic action of microorganism can either directly or indirectly cause deterioration of a metal. Such a process is called biological corrosion.
Microorganisms associated with corrosion are either aerobic or anaerobic. The causes of biological corossion are:
1.
2.
3.
4.

Producing corrosive environment or altering enviromental composition.

Creatin electrolyte-concentration cells on the metal surface.
Altering resistance to surface films.
Influencing the rate of anodic/cathodic reaction.

The role of biologicalmay be explained using anaerobic sulphate using bacteria in slightly acidic or alkaline soils. As these bacteria thrive under
these conditions, they will continue to promote this reaction until failure of the pipe occurss.
Sulphates

hydrogen sulphite + calcium sulphite

On iron in soil
Iron sulphide
(Corrosive product)

PREVENTION AND CONTROL OF CORROSION

Selection of proper material
Corrosion should not be permitted in fine mesh wire-screens, orifices and other items in which dimensions are critical and changes are not
permitted.
Non-mettallic materials are usefuland attractive from the point of view of economics and performance. These should be considered if their
strength temperature design specifications are satisfactory.
Permissible corrosionrates are important factors and differ with equipment. Appreciable corrosion can be permitted for tanks and lines, if
anticipated and allowed for thickness in its design.
The corrosion characterstics of chemicals and limitations of construction materials must be considered from the literature before selecting the
equipment.
In addition, processing conditions to which the material is exposed should be considered.
Proper design of equipment
In designing of equipment, a number of fittings such as baffles, stiffeners, drain nozzles, location of valves and pumps should be considered.
Corrosion can be minimized, if equipment designed facilitates:
Elimination ofcrevices
Complete drainage of liquids
Ease of cleaning
Ease of inspection and maintainance
A direct contact between two metals should be avoided, if they are separated widely in the electrochemical series. Otherwise they should be
insulated.
Coating and linings

Non metallic coatings and linings can be applied on steel and other material of construction in order to combat corrosion.
Appropriate methods such as electropainting cladding,organic coatings should be considered.
Effective linig can be obtained by bonding directly to substrate metal or building multiple layers or lamination.
Organic coatings are used as linings in equipment such as tanks piping, pumping lines and shipping containers.some examples opf linings are:
Ceramic
Carbomn brick
Plastic
Elastic
Glass coated
Organic

 Some examples of lining are:

Tin coated steel (tin plate)
Lead (Pb) coating (Terne plate)
Aluminium (Al) coated steel
Zinc (Zn) coated steel

food containers
roofings
high temperature conditons
many atmospheric conditions

Altering environment
Corrosion can be combated or reduced by employing the following environmental conditions.
Removing air from boiler feed water prevents the influence of water on steel.
Reducing aeration prevents the formation of passive oxide film in stainless steel.
Pumping of inert gas into solutions prevents the contact of air or oxygen as in case of nikel based alloys.
Reducing the temperature.
Eliminating the moisture.
Reducing the velocity or turbulence.
Shortening the time of exposure.
Addition of acid media should be done as the last step, so that maximum dilution can be obtained.
Inhibitors
The corrosion inhibitors are added to the environment to decrease the corrosion of metals. These forms protective films.
Adsorption type, for example,adsorbed on the metal.
Scavenger type, for example, remove corrosion agents.
Vapour phase type, for example, sublime or condense on metal surface.
Examples of inhibitors:
Inhibitors

Chromates, phosphates,silicates
Organic sulphides, amines
Copper sulphate

Cathodic protection

Material protected in medium

- iron and steel in aqueous solution
- iron and steel in acidc medium
- stainless steel in hot dil. solutions of H2SO4

 The cathodic protection is basd on the galvanic action between the metals of the plant and anode suspended in the solution. The metal to be
protected is made a cathode, i.e.,electrons are supplied, there by dissolution of metal is supressed.
This is achieved by 2 methods:
Sacrificial anode method
Impressed emf method
Sacrificial anode method: In this method anode are kept in electrical contact with the metal to be protected (cathode). The anodes are
sacrificed since it goes into the solution.
(For diagram refer-Pharmaceutical Engineering by C.V.S. Subramanyam; First edition;
figure 16.4)

Published by-Vallabh Prakashan; page no.-446;

For example, for the protection of iron and steel tanks, the metal such as zinc, aluminium, magnesium and their alloys are used as sacrificial
anodes. These are used in limited pH range when high soluble rate is acceptable, since these are amphoteric. Anode metal is selected from the
electrochemical series amongst the metal present below the tank metal.
Impressed emf Method: This is also known as applied current system, i.e., external voltage is impressed between tank and electrodes. The
negative terminal of power supply is connected to the material to be protected. Therefore, the natural galvanic effect is avoided and the anode
is maintained positive.
(For diagram refer-Pharmaceutical Engineering by C.V.S. Subramanyam; First edition; Published by-Vallabh Prakashan; page no.-434;
figure 16.2).
Since electrode is not consumed, any conducting material, metal or non-corrodible alloys can be used. For example in case of sulphuric acid
and deionised water, graphite and high silicon steel are compressed. The anodes can be buried I the ground or suspended in the aqueous
solution of electrolyte.
Advantages:
This method is used for large tank to store mild corrosive liquors. In these cases, mild steel is used with negligible corrosion.
Cathodic protection method is simple and most effective.
It is inexpensive. It enables the use of cheaper material for plant construction.
Disadvantage:
Corrosion can not be reduced to zero.

Anodic protection:
In the method a predetermined potential is applied to the metal specimen and the corresponding current changes are observed. During the initial
stage, the current increases indicating the dissolution (corrosion) of the metal. When the current reaches a critical point, passivisation occurs, i.e.,
the oxide layer sets in a suitable oxidizing environment. The potential at critical point is called passivating potential. Above this passivating
potential, the current flow decreases to a very small value called passivating current.

The passivating current is defined as the minimum protective current density required to maintain passivisation.
At this stage, an increase in potential will not corrode the metal since the latter is in a highly passive state. For example, in case of stainless steel,
titanium becomes easily passive and cannot offer cathodic protection. In such cases, the corrosion rate may be slowed down by the use of anodic
current.
Advantage:
Anodic protection requires a small current. The anodic protection method is utilized in the transportation of concentrated sulphuric acid.
Disadvantages:
Corrosion cannot be reduced to zero.
This method cannot be applied for metals, which do not passivate.

A proper material should be selected for a specific process based on the literature and by personal experience. The factors influencing corrosion will
not only help in selecting the right kind of the material, but also suggest the processing conditions. It is equally essential to identify the type of
corrosion, if it occurs. Since the theories are known. It is possible to adopt appropriate preventive measures.
Q4 : Discuss in detail the various types of rectifying columns?
A: Distillation is defined as the separation of the components of the liquid mixture by the process involving vaporization and subsequent condensation
at another place
Fractional distillation can be defined as the process in which vaporization of a liquid mixture gives rise to a mixture of constituents from which the
desired one is separated in pure form. It is also known as RECTIFICATION because a part of the vapor is condensed and returned as liquid. This
method is very useful for separating micisble volatile liquid.
In this type of distillation, special types of still-heads are required so that the re vaporization and condensation can take place at one time only. These
are called RECTIFYING COLUMNS. These are normally a long vertical tube in which the vapour the passes upwards and get condensed and return
to the flask. These are constructed to give following advantage:
It offers a cooling surface for vapour to get condensed .
It give downward flow for the liquid which has high melting point.
It allows easy condensation .

RECTIFYING COLUMNS are mainly of two types:

Packed columns
Plate columns

Packed columns: In this type ,columns are packed in such a form so as to effect the necessary liquid/vapour contact. The packing can have one single
turn of wire or glass, glass rings.
It can be of three types: a. pear shape, b. rod shape,c}disc shape .
Diagram on page no. 320 in Shubarmanyam
Construction: it consist of a tower containing a packing that becomes wetted with a film of liquid , which is brought into contact with vapour in the
intervening spaces.

APPLICATION: Packing must be uniform so as to obtained the good column. If it is irregular then mass transfer becomes less effective. Mainly used
in laboratories . Example of such a column used in laboratories is widmer column.
Plate columns: Many forms of plates are used in the fractionating columns. These can be divided into two main categories:
Bubble cap plates
Turbo grid plates.
[A] Bubble cap plates: this type of plates are used in distillation which are carried out at large scale.
Construction: in this type of column various plates are used which are mounted one above the other and these plates lead to the downcomer. Caps are
placed on each plate which allows the vapour to escape by bubbling through the liquid.
Note: diagram on page no. 321 of Subramanyam
Working: Ascending vapour from the still passes through the bubble caps on the plate A and the rising vapour will be richer in the more volatile
component. And this liquid passes through the second plate and the liquid gets vapourised because the heat of condensation vapourises the liquid.
Same work is done with liquid when it gets on the Third plate and so on all the way up to the column.each bubble-cap plate has the same effect.
Advantage: it is effective over a wide range of vapour-liquid proportions and velocities because it is excellent contact as the vapour bubbles through
the liquid.
Disadvantage: 1. The layer on each plate result in considerable hold-up of the liquid over the entire length.2. the column doesnot drain even after the
completion of distillation.

Q5: Discuss the material and energy balance aspect of a crystallizer. Give working of a agitated batch crystallizer?
Answer:

Crystallization of a substance, is very important pharmaceutical operation, either inorganic or organic, whether on the small scale in a research
laboratory or on the commercial bulk drug manufacture. During the manufacture of the drug, after the reaction is completed in solution resulting in the
formation of a drug or its intermediate, it must be crystallize out of the solution. This is necessary because crystallization if properly carried out results
in the separation of a pure form of the material.
On a smaller scale purity and yield are the main criteria, however in commercial practice additional requirements such as size, range of sizes and
shape are also significant.
Classification of crystallizer:These are classified on the basis of the method by which supersaturation is brought about:Crystallizers:Method 1: Supersaturation by cooling alone, it can be further classified by two methods (i) Batch crystallizers (ii) Continuous crystallizers.
(i) Batch crystallizers- It can be further classified by two methods (i) Tank crystallizer (ii) Agitated batch crystallizer.
(ii) Continuous crystallizer- It also can be further classified in two methods (i) Swenson-Walker crystallizer (ii) Others.
Method 2: Supersaturation by evaporation of the solvent(krystal crystallizer).
Method 3: Supersaturation by adiabatic evaporation, i.e. cooling+evaporation.
Method 4: Supersaturation by salting out.

AGITATED BATCH CRYSTALLIZE

Principle: It is applicable for those substances that have a steep solubility curve where the solubility of the substances rapidly decreases with
reduction in temperature. The solution is generally concentrated in a separate evaporator and then fed to the crystallizer.
Working: In this crystallizer, water is circulated through the cooling coils of the solution is agitated by the propellers on the central sheft.
Agitation increases the rate of cooling and keeps the solution at a more uniform temperature. It also keeps the fine crystals in suspension which can
then grow uniformly without forming too large crystals or aggregates. Thus the product is more uniform in size and is finer than in the older tank
method.
Limitation: It is a batch process & the capacity is low. Further, the solubility of the material is least at the surface of the cooling coils and this results
in rapid build up of crystals on the coil surface resulting in a decrease in heat transfer.
Diagram:- It can be noted by C.V.S. SAMBAMURTHY on page no. 236.

Q6: Discuss the material and energy balance aspect of a crystallizer. Give working of a agitated batch crystallizer?
Answer:
Crystallization of a substance, is very important pharmaceutical operation, either inorganic or organic, whether on the small scale in a research
laboratory or on the commercial bulk drug manufacture. During the manufacture of the drug, after the reaction is completed in solution resulting in the
formation of a drug or its intermediate, it must be crystallize out of the solution. This is necessary because crystallization if properly carried out results
in the separation of a pure form of the material.
On a smaller scale purity and yield are the main criteria, however in commercial practice additional requirements such as size, range of sizes and
shape are also significant.
Classification of crystallizer:These are classified on the basis of the method by which supersaturation is brought about:Crystallizers:Method 1: Supersaturation by cooling alone, it can be further classified by two methods (i) Batch crystallizers (ii) Continuous crystallizers.
(i) Batch crystallizers- It can be further classified by two methods (i) Tank crystallizer (ii) Agitated batch crystallizer.
(ii) Continuous crystallizer- It also can be further classified in two methods (i) Swenson-Walker crystallizer (ii) Others.
Method 2: Supersaturation by evaporation of the solvent(krystal crystallizer).
Method 3: Supersaturation by adiabatic evaporation, i.e. cooling+evaporation.
Method 4: Supersaturation by salting out.

AGITATED BATCH CRYSTALLIZER

Principle: It is applicable for those substances that have a steep solubility curve where the solubility of the substances rapidly decreases with
reduction in temperature. The solution is generally concentrated in a separate evaporator and then fed to the crystallizer.
Working: In this crystallizer, water is circulated through the cooling coils of the solution is agitated by the propellers on the central sheft.
Agitation increases the rate of cooling and keeps the solution at a more uniform temperature. It also keeps the fine crystals in suspension which can
then grow uniformly without forming too large crystals or aggregates. Thus the product is more uniform in size and is finer than in the older tank
method.
Limitation: It is a batch process & the capacity is low. Further, the solubility of the material is least at the surface of the cooling coils and this results
in rapid build up of crystals on the coil surface resulting in a decrease in heat transfer.

Diagram:- It can be noted by C.V.S. SAMBAMURTHY on page no. 236.

Q7: Discuss the material and energy balance aspect of a crystallizer. Give working of a agitated batch crystallizer?
Answer:
Crystallization of a substance, is very important pharmaceutical operation, either inorganic or organic, whether on the small scale in a research
laboratory or on the commercial bulk drug manufacture. During the manufacture of the drug, after the reaction is completed in solution resulting in the
formation of a drug or its intermediate, it must be crystallize out of the solution. This is necessary because crystallization if properly carried out results
in the separation of a pure form of the material.
On a smaller scale purity and yield are the main criteria, however in commercial practice additional requirements such as size, range of sizes and
shape are also significant.
Classification of crystallizer:These are classified on the basis of the method by which supersaturation is brought about:Crystallizers:Method 1: Supersaturation by cooling alone, it can be further classified by two methods (i) Batch crystallizers (ii) Continuous crystallizers.
(i) Batch crystallizers- It can be further classified by two methods (i) Tank crystallizer (ii) Agitated batch crystallizer.
(ii) Continuous crystallizer- It also can be further classified in two methods (i) Swenson-Walker crystallizer (ii) Others.
Method 2: Supersaturation by evaporation of the solvent(krystal crystallizer).
Method 3: Supersaturation by adiabatic evaporation, i.e. cooling+evaporation.
Method 4: Supersaturation by salting out.

AGITATED BATCH CRYSTALLIZER

Principle: It is applicable for those substances that have a steep solubility curve where the solubility of the substances rapidly decreases with
reduction in temperature. The solution is generally concentrated in a separate evaporator and then fed to the crystallizer.
Working: In this crystallizer, water is circulated through the cooling coils of the solution is agitated by the propellers on the central sheft.

Agitation increases the rate of cooling and keeps the solution at a more uniform temperature. It also keeps the fine crystals in suspension which can
then grow uniformly without forming too large crystals or aggregates. Thus the product is more uniform in size and is finer than in the older tank
method.
Limitation: It is a batch process & the capacity is low. Further, the solubility of the material is least at the surface of the cooling coils and this results
in rapid build up of crystals on the coil surface resulting in a decrease in heat transfer.
Diagram:- It can be noted by C.V.S. SAMBAMURTHY on page no. 236.

Q:- Miers super saturation theory of crystallization and vacuum crystallizer.

Ans:- Miers super saturation theory postulate a definite relationship between concentration and temperature at which crystals will spontaneously form
In an initially unseeded solution .
According to it the super solubility curve represents the limit at which nucleus formation begins spontaneously where crystallization can start in the
absence of any solid particle.
A plot of temperature v/s concentration of solute
(NOTE) Refer page no 370 from pharmaceutical engineering C.V.S Subrahmanyam
The curves A B represent the normal solubility any point on the curve represent the solute in equilibrium with the solvent. This is the maximum limit
for the solubility of substance. The curve F G represents the super solubility which is roughly parallel to the normal solubility curve . It represent the
limit at which nucleus formation begin spontaneously.
According to mires theory, crystallization do not start at p but it take place somewhere in the neighborhood of the point D, when certain condition are
specified .
Mier states that under ideal conditions of crystallization of nucleus formation starts at F G and crystal growth begins.
Then concentration of substance roughly follows the curve D E .
Limitation:1) According to Miers theory, crystallization starts at super solubility curve . but generally tendency is that crystallization takes place in a area
rather than a line .
2) Miers theory is applicable when pure solute and pure solvent are used . in practice it is impossible to get them in pure state
3) If the solution is kept for longer period , nucleation starts well below the super solubility curve

4) For crystallization, the solution must be stored for a longer periods . during storage millions of dust particle can enter.
Condition for obeying Miers theory:1) The solution must be free from foreign solid particles.
2) The solute and the solvent must be pure.
3) The solution must be protected from entry of any particle.
4) The solution must be free from solid solute particle.

VACUUM CRYSTALLIZER.
PRINCIPLE:
In vacuum crystallizer, supersaturation is obtained by adiabatic evaporative cooling. When warm saturated solution is introduced into the crystallizer,
due to high vacuum the solution undergoes flashing..
CONSTRUCTION:
Vacuum crystallizer is a cylindrical body with conical shape. A condense is attached to the crystallizer with a vacuum pump in between. The
bottom of crystallizer is attached to a discharge pipe. The internal body of crystallizes can be lined with acid resistant material such as lead or
rubber. Two propellers are placed above discharge pipe to prevent short-circuit of the feed.
(NOTE) Refer page no 378 from pharmaceutical engineering C.V.S Subrahmanyam
WORKING :High vacuum is created using a vacuum pump . the vacuum so created must correspond to a boiling point of the solution . hot saturated solution is fed
into the crystallizer at a convenient point .solution undergoes flashing which results in evoparation of solvent . this process is allowed adiabatically.the
resultantcooling causessupersaturation and crystallization.flashing of the solutionin the crystallizer leads to ebulltion,which keep the crystals in the
suspension.the propellers
mix the content thoroughly and prevent the contents reaching the discharge pipe without flashing.
With the help of pump,the product is collected and subjected to filteration to obtain crystals.the filterate return to the feed..

ADVANTAGES:1) It can be operated either batch wise or continuously.

2) It can be constructed as large size as desired.
3) It is very simple without any moving parts.

USES:Due to low temperature conditions,it is suitable for tharmolabile substance.

RAOULTS LAW-This law states that partial vapour pressure of each volatile constituent is equal to the vapour presssure of each volatile constituent
is equal to the vapour pressure of the pure constituent multiplied by its mole fraction in the solution at a given temperature.
since the solution is homogeneous by definition,the relative numbers of components on the surface reflect the number of these components
components in the whole solution.These numbers can be expressed on the mole fraction scale.thus raoults law is appropriately suited to describe an
ideal solution.
Consider a mixture of miscible liquids A and B.In this mixture :
Let partial vapour pressure exerted by A =PA kpa
Let partial vapour pressure exerted by B = PB kpb
Let partial vapour pressure exerted by the pure component of A=poA kPa
Let partial vapour pressure exerted by the pure component of B=poB kPa
Let mole fraction concentration of liquid A=XA
Let mole fraction concentration of liquid B=XB
Mathematically, raoults law can be expressed as:
Partial vapour
PA= poAXA

pressure

of

liquid=vapour

pressure

of

pure

liquid

multiplied

by

mole

fraction

of

the

liquid.

PB=poBXB
IDEAL MIXING- An ideal solution can be said to follow Raoult's Law but it must be kept in mind that in the strict sense ideal solutions do not exist.
For a solution to be ideal we must assume that it does not matter whether a molecule A has another A as neighbor or a B molecule. This is only
approximately true if the two species are almost identical chemically.
Real solutions
Many pairs of liquids are present in which there is no uniformity of attractive forces i.e. the adhesive and cohesive forces of attraction are not uniform
between the two liquids, so that they show deviation from the Raoult's law which is applied only to ideal solutions.
Negative deviation
When adhesive forces between molecules of A and B are greater than the cohesive force between A and A, or B and B, then the vapor pressure of the
solution is less than the expected vapor pressure from Raoult's law. This is called a negative deviation from Raoult's law. These cohesive forces are
lessened not only by dilution but also attraction between two molecules through formation of hydrogen bonds.This will further reduce the tendency of
A and B to escape.
For example, chloroform and acetone show such an attraction through a strong dipole-dipole interaction.
Positive deviation

When the cohesive forces between like molecules are greater than the adhesive forces, the dissimilarities of polarity or internal pressure will lead both
components to escape solution more easily. Therefore, the vapor pressure will be greater than the expected from the Raoult's law, showing positive
deviation. If the deviation is large, then the vapor pressure curve will show a maximum at a particular composition, e.g. benzene and ethyl alcohol,
carbon disulfide and acetone, chloroform and ethanol.
NOTEFOR DIAGRAMS,,PLEASE REFER SUBRAMANYAM PAGE NO.-297,FIRST EDITION.
VOLATILITY- Volatiility of a substance in a solution may be defined as th equilibrium partial pressure of the substance in the vapour phase divided
by the mole fraction of the substance in the solution.
for example, a substance A in liquid mixture has partial pressure Pa and its concentration in the mixture is Xa on mole fraction scale. then volatility
of A may be mathematically expressed as:
volatility of component A,=partial vapour pressure of A/mole fraction of A in solution.
thus volatility of a material in the pure state is equal to the vapour pressure of the material.
RELATIVE VOLATILITY-Consider a liquid mixture containing two components A and B. in such a case,the volatility of one component is
expressed in terms of the second. RELATIVE VOLATILITY may be defined as :
Relative volatility,R=volatility of component A/volatility of component B
Relative volatility is commonly expressed with the higher of the two volatilities in the numerator. This means that the relative volatility should never
have a numerical value less than 1.

Q: Discuss in detail about heat and material balance.

Q: Explain theories of size reduction.

Q: Give methods of size separation.