Some types of distortion found in sound systems, other

than misuse, feedback, reflections or the resonance of

speaker cabinets, windows, floors, tone arms, etc, can
comprise;
THD | Transient distortion | Cross-over distortion |
Clipping | Noise
Instabilities | 'Paranormal' Audio | A Tip
Using good quality audio equipment of, say, early '80s
vintage a record deck could produce 3-6% with 8-10%
being typical, even with the best cartridges and records.
A reel-to-reel tape deck would give 2-3%, cassette
decks doubling this although the variation between
individual cassettes was much greater. Tuners gave
some 0.2-1% providing the highest quality source for
domestic users. Monitor quality speakers giving say
80dB @ 1W would produce about 0.3% in the midrange and 1-2% at lower frequencies.
THD
When fed with a signal, some parts of an amplifier's
circuitry will resonate at multiples, or harmonics, of the
input signal. THD, or total harmonic distortion, is often
cited in the specification of an amplifier and is seen by
many as a measure of how well an amplifier performs.
Two graphs, below, show how a single figure (in this
case <0.1%) stated in a specification can be
meaningless when the THD can vary considerably with
load and frequency.

0.1% seems not only arbitrary but optimistic as well.

Note how 3rd, and therefore odd, harmonics
predominate at higher frequencies. These are more
noticeable and considered more objectionable than 2nd
harmonics which are interpreted as having a 'musical'
and therefore acceptable quality. A very rough rule of
thumb multiplies the THD by three at 20kHz, when
quoted at 1kHz.
Temporal aspects of audio processing, inherent in
hearing, produce pronounced variables in perception.
For example, long periods of high distortion are more
objectionable than short bursts and longer term
exposure to a specific level increases sensitivity. At the
same time, THD peaks at low frequencies are far more
difficult to detect than those of the same amplitude in
the mid-range.
Most THD measurements are made using a continuous
sine wave and take no account of performance when the
amplifier is driven by other waveforms or transients
normally found in music. The human ear is less
sensitive to harmonic distortion than it is to other forms
and this is why some specs will provide maximum
output ratings at 10% THD.

Transient distortion
When driven by a signal with sharp rise and fall times
like a square wave 'overshoot' can be observed.

Caused by a transistor's parameters inconvenient habit

of changing with collector current, most would agree
that this problem can be rendered inaudible if the
amplifier is designed to be sufficiently fast, or operated
in class A, eg;

Simulated loads may have very little in common with

reality given the very lively reactance represented by
some speaker enclosure designs, their associated crossovers and 'low-loss' wiring. Jim Lesurf, a designer with
Armstrong, has an excellent site where he mentions
'The Society for Cruelty to Amplifiers'.
Intermodulation problems can arise when a power
amplifier's output 'lags' behind a fast transient that
appears at it's input, the resulting feedback creating a
distortion that the ear is as sensitive too as cross-over
distortion. This problem can be overcome by making

each successive stage of an amplifier faster than the

preceding one and by using a low-pass filter at the
input. It is for this reason that the class A pre-driver
usually found in a power amp design has to be the
fastest, or selected for a very low base capacitance.
High voltage types are recommended.
A 'good' slew-rate for 20kHz at 100W into 8 ohms is
usually considered to be 20V/S or better. Some
designs exceed this by a considerable margin. Smaller
amplifiers do not have to slew so quickly, so a similar
50W amplifier needs 14V/S and a 20W amp 9V/S. If
an output stage uses 'slow' transistors (say 800kHz) a
marked improvement in high frequency performance
will be produced by replacing them with 'fast' ones (say
4MHz+), often accompanied with a distinct drop in the
THD.
Experience has suggested that, when comparing two
amplifiers, one with 0.03% THD and 0.01% IMD will
sound better than another with 0.01% THD and 0.03%
IMD.
Normally, a low roll-off Bessel filter is placed at the
input so that the phase shift is proportional to
frequency, causing the time lag to be the same for all
frequencies, with no audible consequences ('ringing').

Such a filter can be useful in blocking RF breakthrough.

With some capacitive loads, ringing caused by the
inductor in series with the output (intended to
counteract this problem) can be reduced if the coil is
replaced with a low-value, say 0R22, non-inductive,
heavy-duty resistor. 'Super' speaker cables can be
major contributors to this kind of problem and are best
avoided.
With large output voltage swings, time delays taken by
the capacitor decoupling the AC feedback loop to charge
and discharge can modulate the output.

A detailed manufacturer's discussion of steps taken to

reduce TID can be found here.
Clipping
This occurs when the amplifier is driven so hard that, in
effect, it runs out of power supply, the peaks of the
signal then being cut off, or clipped. Overdriven
(usually) speaker cones, still moving, 'overshoot' thus
producing objectionable harmonics. It is this particular
distortion that has most people rushing to 'turn it down'
and quite rightly too since silence will usually follow.
The same result occurs when some protection circuits
kick in, especially those triggered by an over-current
condition through the output device's emitter resistors
when using reactive loads that dip below a couple of
ohms or those that generate a back EMF. It is for this
reason that an upgrade to a new speaker especially a
low impedance one, and/or 'strange' cables, may prove
unsuccessful and, in the worst case, disastrous. It is
wise to try a given amplifier / speaker combination at
the highest volumes that can be more than reasonably
expected before commiting to an expensive purchase. If
in doubt, fit a low resistance, say 1R, or suitably rated
bulb in series with the load.
Cross-over distortion
Each time an amplifier output of non-inverting or
inverting configuration crosses zero a point is reached
when 0V occurs across the feedback resistor (R2
below). Since no current flows the amplifier then 'sees'
an infinite resistance, altering the gain characteristics of
the circuit. In reality, this phenomenon is usually
ignored by designers.

The circuit found strung between the bases of the driver

transistors 'ties' them together so that the output does
not pass destructive amounts of current. It does,
however, allow a little current (quiescent) to flow so that
the output devices are biased on. A well-used example
is shown below:

Sometimes described as a 'variable zener' or 'amplified

diode', it can also be used to reduce the overcurrent
conditions that arise with hot bipolar output devices
(NTC, negative temperature coefficient). If the
transistor is put in close proximity to a heat-sink, output
device or, sometimes more conveniently, bonded to a
driver, closer thermal tracking can be obtained. Some
prefer to fit a resistor between the transistor's base and
collector to overcome potentially destructive wiper
open-circuits.
The time it takes for the output of the amplifier to swing
or slew across this small voltage drop, as it approaches
zero, gives rise to cross-over distortion which can be
seen easily on an oscilloscope.

Subtracting the input from the output and imposing this

on either can demonstrate and pinpoint not only

inadequacies but improvements too (Technics 'New
Class A' on left, class B on right).

Alternatively, using the input of the amplifier as the x

axis, and the output as the y and adjusting the
respective amplitudes, a perfectly behaved amplifier will
give a straight line at 45, cross-over distortion appears
as a kink in the middle (positive-going for class AB,
negative for class B). Adjust the bias setting (R3) for
minimum distortion at progressively higher output levels
and higher frequencies. Clipping, if desired, and the
effects of filters and tone controls can also be displayed,
some very interesting results being obtained from some
very well-known makes!

It was cross-over distortion that distinguished, in sonic

terms, early solid-state designs from their thermionic
equivalents. This was described as "the transistor
sound" a quality of sharpness and crispness that,
allegedly, makes valves sound muddy by comparison.
Interestingly, it has been noted by the author, and
others, that cross-over and other types of distortion
become audible at the same time they become visible
on a 'scope.

It has been noticed that many manufacturers insist on

using a low quality open carbon skeleton preset pot to
adjust the quiescent current. These are prone to
corrosion and open circuits that can then destroy an
output stage. It should be noted also that a carbon pot
can exhibit 10 times the thermal drift of a comparable
cermet type. Given the cost of the output devices alone
care should be exercised to avoid unnecessary failures
and quality sealed types should be specified and used to
replace older ones. If the wiper has multiple contacts
this will enhance performance.
The layout of an output stage can affect the stability of
the bias and J. N. Ellis drew attention to this
(EW&WW,1/91). The quiescent flow in the 0R5 resistors
(below) will rise as the Vbe of both output devices rises.
This can cause an increase in a driver's Vbe giving a
4mA increase per C rise per pair. With two pairs this is
doubled, as does each driver's Vin.

Typically, in a conventional Darlington circuit, the output

base resistors are 100R, the quiescent current 50mA
and driver current about 6mA. At room temperature the
Vbe of the output devices will be about 0V55 and that of
the drivers 0V65.

The bias transistor may be passing 10-15mA and then

will have a higher Vbe than the drivers. A voltage drop
of, say, 2V4 will be required and the bias transistor will
be operating with a Vbe some 20mV higher than the
driver. 2V4 / 0V67 is only 3.58 when a value of 4 is
needed to be thermally stable.

With a higher-power bias transistor, with a larger

emitter area, the Vbe at the same emitter current will
be lower. Inserting a resistor in the collector increases
the bias voltage needed whilst any drift will be
transferred to the output devices. Suppose the bias

current is 12mA and 4Vbe = 2V68 bias. Rc then =

(2V68 - 2V4) / 12mA = 22R, a larger value then overcompensating. In a complementary Darlington stage,
small resistors in series with the driver's emitters will
raise the bias voltage needed. At 6mA 3R3 will suffice,
the loss at peak drive, say 200mA, giving an acceptable
0V66. Higher values will increase the compensation.
Thermally coupling the bias and driver transistors will
then prevent thermal runaway, eg;

As the output device Vbe falls with increasing

temperature, the driver current decreases slightly while
the output current increases slightly and must be taken
into account when designing the bias circuit for the
maximum temperature range anticipated for the
amplifier. The above can be used to modify an existing
design. Compare to PMI, Giesberts IGBT and Stochino.
For new builds M. Renardson offers another approach
with 'A New Audio Amplifier Circuit Design'.
A quasi-complementary output stage can ease output
device selection and reduce costs, it being easier and
cheaper to produce PNP devices in germanium, and
later, NPN in silicon which could run hotter. A drawback
encountered with this arrangement is that the transfer
characteristic can become markedly assymetrical at low
signal levels, then contributing to distortion. For this
reason, low-level distortion figures are usually absent
from an amplifier's specification.
The use of feedback, say, the use of a RC network
between the input of the class A driver stage and the
output (see TID discussion above) with conventional
external feedback will reduce cross-over distortion
considerably, or it can be eliminated if the output stage
is fast enough to render this transition inaudible or if the
quiescent current drawn is high enough for the output
transistors to continuously operate in their linear fT
regions (class A - see MJL3281A graph above). The low-

level distortion found with other types of amp will also

be eliminated. Power supplies and heat-sinking will,
however, then have to be commensurately larger to
sustain these very large losses, efficiency becoming a
minor consideration.
'New Class A' was intended by Technics to impart the
low-level distortion of class A with the efficiency of class
B. This was achieved by clamping the driver bases so
that the output devices conducted over the transition
period. The result impressed this author, and many
others.
With a class AB configuration, the driver stage will often
drive the load in class A mode up to a low output level,
say 2W, beyond which the main output devices will
kick-in providing higher drive. On the central part of the
transfer characteristic where both output transistors are
conducting the mutual conductance (gm) doubles. When
one of the output devices cuts off as the circuit goes
into class B mode the abrupt change in the slope of the
transfer characteristic can produce a considerable rise in
distortion.
Class B amplifiers, probably the commonest format
seen, rely on a small quiescent current through the
output devices to overcome transition phenomena
although some designs will have none. Usually reserved
for low-quality builds, some very famous and desirable
amplifiers have operated in this mode.
In class C designs, where the cross-over transition can
be comparatively quite considerable, an inaudible HF
component can be added to the input signal which 'fillsin' the cross-over point, subjectively reducing distortion
by a large margin.
With class D designs the output voltage is derived as an
average as the output is switched directly between the
supply rails, there being no consequent zero-crossing
transition.
Classes E and F are not normally used in audio but, as
with other modes of audio amplifier operation, can be
useful in motor control, welding applications, etc.
Class G, in essence, has the same operating mode as
AB or B, with additional output pairs being wired in

series to help reduce output stage dissipation and are

commonly used to achieve high (1kW+) outputs.
Class H designs switch in a higher voltage supply rail to
cope with peaks. The basic arrangement for the Philips
TDA1560Q IC, intended for automotive use, is shown
below.

A novel approach, 'class S' (below), showed that if the

load presented to the voltage amplifier by the power
output stage appears very high, cross-over distortion
can be reduced and the voltage amplifier is much easier
to design.

Class T is a variation of Class D introduced by Tripath,

where the pulses are modulated based on the individual
characteristics of the output transistors.
Noise
Connectors, switches and other mechanical contacts in
controls can introduce anything from a faint crackling to
an open circuit, a good contact only being possible when

one contact breaks the surface of, and penetrates, the

other, consequently causing problems when worn or
dirty. At low signal levels, the consequences are
obvious. Electronic switching, although sometimes
complex, can overcome these difficulties.

It makes sense to position the stages where most

amplification (and/or equalisation) takes place as near
to the source as possible, eg; a record-deck fitted with a
RIAA preamp. In an electrically noisy environment, a
higher output will sustain a comparably lower noise floor
than a much smaller signal. The number of switches and
connectors that can degrade the signal is also reduced.
The deck can, if desired, then (via a volume control)
feed a power amp directly.
Some designs used PCBs with edge-connectors where
the units were based on a set of PCB cards that could be
slotted in and removed easily. This made the system
quite flexible to manufacture and meant that any units
sent for repair could often be fixed quickly by relatively
unqualified staff simply by swapping faulty boards which
might then be repaired by a more experienced engineer
using a dedicated rig. Examples include the Leak Delta
and Armstrong 400/500 series. Unfortunately, these
connectors could corrode or oxidise, themselves giving
rise to failures. This corrosion could be caused by the
fingerprints left by production and service staff. In this
type of construction, attention given to these connectors
in a non-functional unit will often restore it.
Destructive connector problems can arise when a power
amp is split between PCBs like the 2 used in the Radford
HD250, the 3 in the Powertran JLH 70W Deluxe and the
2 in the RSD 800b although the latter used a highquality multi-pin connector whose pins were paralleled.
A DC presence can cause noise in controls, to avoid this
AC couple any pots, particularly volume controls. In an
older design this can be indicative of leaky coupling
capacitors which should be replaced.

Magnetisation of tape heads could introduce hiss and

crackling. Tape repeatedly passing magnetised
metalwork can lose it's treble content. The Beocord
5000's bias oscillator would damp on shutdown,
degaussing the record head automatically.
Electronic hiss is usually associated with Johnson noise,
which is normally dependent on the temperature of an
electronic device and it's associated impedance, or
resistance, which can change with it. The more circuits
in series (say a preamp, tone control and filter) the
more hiss. On a mixing desk unused channel's noise can
be used to cancel the noise in those used thus making
the system quieter and increasing it's dynamic range.
As with distortion, noise figures can confuse, unless one
is an engineer, which most music listeners are not.
Differing standards involving filtering can appear to offer
lower quoted specs which can appeal to marketing, eg;

Low-noise amplifiers usually refer to an input load

impedance to describe their noise output, whilst others
give a measured mean voltage and bandwidth. Simply
stating an A-weighted figure without a reference can be
deliberately meaningless, as can measuring the output
when the input is shorted. In the course of building
preamps, a means of quantifying noise output was
required and a relatively simple means of obtaining
comparative measurements is described here.

Power supplies can be considerable noise generators,

the importance of mains filtering cannot be
underestimated, many commercial designs suffering as
a consequence of an almost mandatory and complete
absence. 2nd and 3rd line harmonics can be very
annoying as can by-products of rectification. 'Barrier'
techniques, like those shown below, can be very
effective, the first from a class A amplifier reducing
noise by 20dB.

Pre-regulation, ie; running say 15V regulators from 24V

regulators, in conjunction with plentiful smoothing is
advisable for low-noise designs, although batteries are
useful for critical low-level applications. Some 78x/79x
series regulators can be very noisy compared to
adjustable types like the LM317/37 types. A post filter
of a 10R resistor and a 470F-1mF electrolytic can help
alleviate this, although discrete designs can arguably
outperfom ICs in this context.
It is important to add supply by-passing to a stage's
supply rails to reduce noise. Often, with opamps this is
done with a 0.1F ceramic cap and a 100F electrolytic
per supply rail. Some fast opamps, like the AD797,
require the usual ceramic but also a tantalum of 4.7 to
22F whose lead inductance is loaded with a carbon
resistor of 1.1 to 4.7 ohms when driving heavy loads.
Hum can have a number of origins - inadequate
screening, earthing or supply smoothing. All connecting
media must be sound and clean. Steel is recommended
for all cases and a maximum distance should be made
between any transformers and low-level circuitry. For
example, the integrating of an mains on-off switch and
high impedance volume control may make ergonomic
sense but may increase susceptibility to hum. Additional
screening between these or around the low-level
circuitry can help. Employ star or spider earthing
(bringing all earths to a single point) throughout to
prevent circulating currents.

Observing symmetry in supply arrangements will avoid

audible ripple, earth connections to multiple smoothers
often being made with a single plate.

If a connection causes an earth loop (disconcerting

hum), disconnect one of the concerned grounds. A
colossal hum, accompanied by a chorus of radio
stations, usually indicates a disconnected signal earth.
Some equipment is fitted with an earth-lift switch which
isolates the signal ground from the (safety) chassis
ground. Some 'separates' designs will have, say PCB
selectable, ground options. If a ground is lifted, an HF
path to chassis (capacitor) usually improves and is best
made permanent.

Mains-borne noise, especially spikes, can cause

annoying clicks, bangs and even destroy speakers and
components. A solution is considered here. Care should
be taken to ensure that prior to any switching, a resistor
grounds decoupling capacitors so that no DC shift, due
to leakage, produces transients.
Instabilities
Half of the 'fun' involved when building an electronic
project for the first time is making it work when
completed. Oscillators won't oscillate and amplifiers may
do nothing but. Sometimes the cause of misbehaviour
will be obvious, sometimes not. Reactive loads, for
example, can cause all sorts of problems (see amplifier
protection). Thermal drifts may be masked by
hysteresis.
If embarking on a new build or repair, some useful
advice is given in setting up an amplifier. If no 'scope or
frequency meter is available, oscillation may be hard to
spot. However, if a power amplifier (other than class A)
runs hot, components start 'cooking', bias is excessive,
next door appear to be using their electric drill a lot or
radio breakthrough occurs and no obvious DC bias is
present on the output, the chances are that there is a
problem in this area. Check the RC network (Zobel,
Boucherot) between the output and ground, if fitted, for
open circuits (many manufacturers insist on a feeble
resistor in this position). If this checks out, look at the
small decoupling caps near the class A driver (if class A,
AB) or the input devices (usually small ceramics) for
open circuits. If no means is available to test these,
simply replace them. Similar symptoms can arise from
dry joints or cracked tracks, so check for these first. The
class A driver, if replaced with a type with a higher than
intended Cbc (say, 1-5pF), can give rise to oscillation.
V-FETs can oscillate if their gates aren't loaded with
resistance or if their supply runs are (relatively
speaking) high impedance. Low value ceramic (lowinductance) supply decoupling caps (usually 01F)
should be mounted as close to the output devices as
possible.

Consideration can be given to the drift of a capacitor's

value with temperature (High K) and lifespan when
mounted in close proximity to a heat source like a heatsink. Choose a high voltage type, say 1kV for supply
decoupling, and use more than one per PCB track.
Oscillation can occur when a test instrument's leads
(DVM, 'scope) are applied to the unit under test. To
prevent this, load the probe attached to the signal side
with a resistor, say 680R. HF problems can cause
equipment to radiate over a large area and must be
avoided, often by law. Whilst steel is recommended for
screening, care must be taken if equipment is
dismantled and then unshielded.
When dealing with PAs say it can be useful to subtract
the input from the output. Artefacts, like cross-over
distortion and oscillations, can then be easier to spot
with a variety of frequencies and waveforms.

If a design, particularly one with a wide bandwidth,

proves problematic consider whether capacitors
intended to limit the bandwidth may be interacting, eg;

In fig 1, Ca may be included to counteract coupling

between the input and output. Both Ca and Cb may not
interact on one build but will in another. Reversing the
RC network (R-Cb, fig 2) will place R between them
reducing the interaction. Alternatively, Rx can be fitted.
A small value, say 68R, should suffice.
With compact builds the PCB layout can be a cause of
instabilities necessitating the use of extra compensation
caps to damp oscillation which may only arise at high
levels of volume. This can be caused by high magnetic
fluxes inducing currents in high impedance low-level
areas. As a consequence, keep a distance between the
inputs and the output/supply rails. If this is not possible,
put a screen between them. Some cases have been
seen where an improvement in distortion has been
made by running the supply wires (twisted together)
perpendicular to the plane of the PCB over a few inches.
Instabilities can arise when high current earth wiring
follows the same path as that used for low currents.

Sometimes the problem may only be apparent

intermittently when high currents are passed through,
say, a thin PCB track. A length of tinned copper wire
soldered along the track's entire run can help prevent
this, although all tracks on a new PCB should be tinned
as a matter of course. Such steps are recommended for
all high current runs in new builds before populating the
rest of the PCB. Older, especially commercial, designs
can benefit from this modification also.

Small value capacitors should be mounted close to their

associated components keeping track lengths as short
as possible. Self-inductance will increase if leads are
bent. If a long track length is unavoidable (>20mm),
this should be at a low operating impedance, or have a
multiple path. The inductance of long tracks in
conjunction with a capacitor can form a very high Q LC
tuned circuit, and the oscillations produced will have a
worse effect than not having any decoupling at all. This
is particularly true of supply and ground connections - a
simple jumper wire connection, rather than a copper
track, to a single logic IC ground caused enormous
difficulties for one constructor.
Similarly, mount transistors close to the PCB. Long lead
lengths can induce a variety of HF/VHF problems,
especially if associated with high impedances, gains and
currents adding to colourations. The view below shows
how not to layout an output stage, although such
occurences may be more down to the manufacturer's
production team, rather than the original designer.
Output devices with a low fT can probably cope with
long runs like this but if the author was presented with
an unstable new build of this format a reduction in
wiring length would be on the cards.

Another design whose PA PCB tracks could have been

rotated 90. Note also how the PA input leads (white)
snake around the board and are then held in place by
unrelated components. The signal path should flow
topographically from input to output.

Some ICs, whether opamps or regulators, can become

more prone to instability at higher operating
temperatures, particularly if of commercial grade.
Loading the inductance of the leads of a tantalum
capacitor with a low-value carbon resistor might be
required in bypassing some high frequency opamp's
supplies. The voltage dependence of a ceramic type's
value can give rise to unwanted changes in frequency
response, especially if used in feedback paths. For this
reason, polystyrene types maybe preferable.
If mounting axial-leaded resistors in an upright position
to reduce PCB area, the longest lead should be
connected to the least impedance 'seen', thus reducing
the area of a 'sensitive' high impedance side. The same
can be said of polystyrene caps which if marked at one
end indicates that wire is connected to the outermost
foil and is then ideally connected to the least
impedance.

Components exhibiting intermittent faults (which can

have the highest annoyance level), say on warm up, can
sometimes be identified by tapping with an insulated
object, cooling with freezer spray or gentle heating with
a small soldering iron brought into close proximity to
them.
Sometimes the source of fault may be in an ancillary
circuit, like a protection circuit, and not the amplifier "There was no DC triggering the circuit from the emitter
resistor. It was cross talk and leakage and only
happened in musical transients as you can get a net DC
level high impedance trigger input and boom false
trigger. Turned out the (DC) V Sense transistor was
floating some track break that could not be seen
and I obviously failed to measure. I double tracked the
PCB around the area and it works fine. If I had listened
first, I would have realised that there were no cracks or
pops in the music as the triggered fired hence no odd
DC sifts etc. Relied too heavily on a scope!".
Full bridge amplifier designs increase the chances of HF
instabilities. Ensure that a very low impedance ground
exists between both amplifiers and that the DC offset of
each is as close to zero as possible. Although useful for
say doubling the slew rate and increasing output power,
experiments with these are best left to experienced
constructors since double the damage can occur.
As noted above, destructive connector problems can
arise when a power amp is split between PCBs or if long
wiring runs are involved in the power stages. For this
reason, it is recommended that new designs be built on
a single PCB or substrate. If a multi-way connector is
unavoidable choose a multi-, say 3-row, type with as
many pins that will fit the PCB and parallel the pins in
adjacent rows - the more the merrier. Select a hard
gold-plate with high current rating (2A+) with as low a
contact resistance as possible, say 15 milliohm.
A Tip
Much of the travel on an average volume control is
redundant, most domestic amplifiers giving a sufficient
volume at about '2', with objectionable distortion, either
of amplifiers or speakers, occuring long before the end
stop. If the gain of the power amplifier is reduced to suit
and set below clipping at all normal preamp settings of

the programme material at the maximum volume

setting, bandwidth will be increased. The amplifier will
then be better able to tackle nonlinearities. At the same
time the input referred noise floor will be reduced and
the signal to noise ratio will improve.
Many preamps will supply signals far in excess of line
levels, some at 10 or even 20V. Accommodating and
even using this will further reduce contributory noise
levels from power amps. To this end, some users have
impedance converting amplifiers, in some cases having
no voltage gain or feedback.
Power Supplies | Protection | Layouts and Heat-sinking |
Dimensioning a design | Setting up an audio amplifier
Contact me at [email protected]
especially if you want additional content to this page
or if you find any links that don't work. Don't forget
to add the page title or URL. Take care!
Back to index, sound, tips or home.

Sponsored by