Installation PDF
Uploaded by
luk@_sInstallation PDF
Uploaded by
luk@_sALCATEL 9400 AWY Rel.2.
0
Installation Handbook
7 - 8 - 13 - 15 - 18 - 23 - 25 - 28 - 38 GHz
Short-Haul Low/Medium Capacity Digital Microwave Radio Links
ED 05
3DB 06687 DAAA
1/178
TABLE OF CONTENTS
1.
HANDBOOK GUIDE ................................................................................................................................. 8
1.1. Copyright notification............................................................................................................................. 8
1.2. Notice .................................................................................................................................................... 8
1.3. 9400AWY Rel.2.0 Customer Documentation set.................................................................................. 8
1.4. History, applicability and purpose of this manual................................................................................10
1.5. Handbook history, scope and related documents...............................................................................11
2.
SYSTEM TECHNICAL CHARACTERISTICS ........................................................................................12
2.1. System temperature condition tolerated .............................................................................................12
2.2. System Voltage working condition ......................................................................................................12
2.3. System Mechanical characteristics .....................................................................................................13
3.
INSTALLATION RULES .........................................................................................................................14
3.1. Safety Rules ........................................................................................................................................14
3.2. General Rules .....................................................................................................................................14
3.3. EMF safety instructions.......................................................................................................................15
3.4. Unpacking and Warehousing ..............................................................................................................16
3.4.1. General .......................................................................................................................................16
3.4.2. Unpacking...................................................................................................................................16
3.4.3. Warehousing ..............................................................................................................................17
3.5. Pre-Installation Checking ....................................................................................................................17
3.5.1. 1+0 Integrated Antenna.............................................................................................................17
3.5.2. 1+0 NON Integrated Antenna....................................................................................................17
3.5.3. 1+1 Integrated Antenna..............................................................................................................18
3.5.4. 1+1 NON Integrated Antenna.....................................................................................................18
3.5.5. OUTDOOR UNITS CHECK........................................................................................................19
3.5.6. RF COUPLER UNIT CHECK .....................................................................................................22
3.5.7. INDOOR UNIT TYPES CHECK .................................................................................................25
3.5.8. INTEGRATED POLE MOUNTING INSTALLATION HARDWARE KIT CHECK........................27
3.5.9. NON INTEGRATED ANTENNA POLE MOUNTING INSTALLATION HARDWARE KIT
CHECK 31
3.6. Installation Tools required ...................................................................................................................35
3.7. Tables of installation IDU-ODU components ......................................................................................35
3.7.1. Integrated or Not Integrated antenna installation components ..................................................35
3.7.2. IDU installation components.......................................................................................................45
4.
OUTDOOR UNITS INSTALLATION (ODU) ...........................................................................................47
4.1. General................................................................................................................................................47
4.2. TRANSCEIVER (A-box) and BRANCHING (D-box) boxes coupling..................................................49
4.3. Typical installation layout ....................................................................................................................50
4.4. 1+0 ODU configuration Installation with integrated antenna...............................................................55
4.4.1. Required Parts............................................................................................................................55
4.4.2. Pole mounting assembly ............................................................................................................55
4.4.3. General Procedural Sequence: ..................................................................................................58
4.4.4. Procedure note ...........................................................................................................................58
4.4.5. Installing the pole mounting on mast .......................................................................................58
4.4.6. Installing the antenna on the pole mounting...............................................................................59
4.4.7. Installing the ODU ......................................................................................................................60
4.4.8. Pointing the antenna...................................................................................................................61
4.4.9. Installation on the wall information .............................................................................................64
4.4.10. Antenna 3 / 4 Feet Installation Instructions ................................................................................65
4.5. 13-38GHz - 1+1 ODU configuration Installation with integrated antenna...........................................67
4.5.1. Required Parts Listing ................................................................................................................67
4.5.2. 13-38GHz - 1+1 Typical installation (General Procedural Sequence) .......................................68
4.5.3. 13-38GHz Change polarization in 1+1 configuration .................................................................70
4.6. 7- 8GHz 1+1 ODU configuration Installation with integrated antenna (Alternative A) .......................72
4.6.1. Required Parts Listing ................................................................................................................72
4.6.2. 7- 8GHz 1+1 Typical installation (General Procedural Sequence) ............................................73
4.6.3. 7- 8GHz Change polarization in 1+1 configuration ....................................................................75
4.7. 7- 8GHz 1+1 ODU configuration Installation with integrated antenna (Alternative B) .......................76
4.7.1. Required Parts Listing ................................................................................................................76
ED 05
3DB 06687 DAAA
2/178
4.7.2. 7- 8GHz 1+1 Typical installation (General Procedure Sequence) .............................................77
4.8. 1+0 ODU configuration Installation with non-integrated antenna........................................................80
4.8.1. Required Parts Listing ................................................................................................................80
4.8.2. General Procedural Sequence ...................................................................................................80
4.8.3. Install the pole mounting on the mast.........................................................................................81
4.8.4. Installing the ODU.......................................................................................................................82
4.8.5. Installing the Flextwist waveguide............................................................................................83
4.9. 13-38GHz - 1+1 ODU configuration Installation with non-integrated antenna...................................84
4.9.1. Required Parts Listing ................................................................................................................84
4.9.2. General Procedural Sequence ...................................................................................................84
4.9.3. Installing the Coupler ..................................................................................................................85
4.10. 7- 8GHz - 1+1 ODU configuration Installation with non-integrated antenna (Alternative A)..............86
4.10.1. Required Parts Listing ................................................................................................................87
4.10.2. General Procedural Sequence ...................................................................................................87
4.10.3. Installing the Coupler ..................................................................................................................87
4.11. 7-8GHz Installation Full Indoor AWY (Two Terminal) ......................................................................90
Table 17 - AWY 7/8 GHz Installation code Full Indoor housing kit ..............................................................93
4.12. 7- 8GHz - 1+1 ODU configuration Installation with non-integrated antenna (Alternative B)..............94
4.12.1. Required Parts Listing ................................................................................................................94
4.12.2. General Procedural Sequence ...................................................................................................94
4.12.3. Installing the Coupler ..................................................................................................................95
4.13. Solar shield Installation........................................................................................................................97
4.14. IDU / ODU cable grounding kit assembling.........................................................................................98
5.
INDOOR UNITS INSTALLATION (IDU) ..............................................................................................100
5.1. General..............................................................................................................................................100
5.2. Rack mount kit description ................................................................................................................100
5.2.1. Rack mount installation in ETSI (WTD) and North American standard rack............................100
5.2.2. Laborack ...................................................................................................................................104
5.2.3. Rack mount adapters installation in a rack...............................................................................105
5.2.4. Grounding of the subrack .........................................................................................................106
5.3. Minimum distances between systems installed in the rack...............................................................107
5.4. Wall mounting kit description.............................................................................................................109
6.
IDU INTERCONNECTIONS ..................................................................................................................110
6.1. Module interconnections, description ................................................................................................110
6.1.1. IDU ODU cable disconnection/connection ............................................................................111
6.2. Numbering and functions referred to the Connection Points ............................................................117
6.3. Summary and type connectors usage...............................................................................................120
6.4. Suggested cabling .............................................................................................................................121
6.4.1. Split Cable.................................................................................................................................122
6.4.2. Inter- connection Main Extension flat cable...........................................................................124
6.4.3. I/O 1 through 8 and I/O 9 through 16........................................................................................125
6.4.4. Mini Distributor connection .......................................................................................................127
6.4.5. NMS V11 - AUDIO 1 (EOW).....................................................................................................128
6.4.6. NMS G703 + Audio 2 (EOW)....................................................................................................129
6.4.7. NMS INTERFACE AWY-MELODIE..........................................................................................130
6.4.8. Service Channel........................................................................................................................131
6.4.9. Housekeeping Alarms...............................................................................................................132
6.4.10. E3 - DS3 ...................................................................................................................................133
6.4.11. M, LT, LEDs (housekeeping, Summarizing).............................................................................134
6.4.12. OS DEBUG ............................................................................................................................135
6.4.13. CT access .................................................................................................................................136
6.4.14. R - Reset pushbutton................................................................................................................136
6.4.15. TPH Telephone Handset .......................................................................................................137
6.4.16. IDU ODU connections ..........................................................................................................138
6.4.17. 50 Ohms connector assembling ...............................................................................................139
6.4.18. Power Supply connector, On / Off switch .................................................................................141
6.4.19. ON-OFF switch .........................................................................................................................142
7.
CAPACITY EXTENSION.......................................................................................................................143
ANNEXES ......................................................................................................................................................144
ANNEX A CABLE CODE INTERCONNECTIONS DESCRIPTION..........................................................152
A.1. Cable 3CC52130AAAA (L.= 1.6m) or 3CC52131AAAA (L.= 6.4m)..................................................166
ANNEX B NETWORK INTERCONNECTIONS.........................................................................................167
B.1.1. NMS Continuity .........................................................................................................................167
ED 05
3DB 06687 DAAA
3/178
B.2. AWY-MELODIE SNMP Interconnections Cable list.........................................................................172
ED 05
3DB 06687 DAAA
4/178
LIST OF FIGURES
Tables
Table 1 - ODU Mounting Hardware Installation Kit Listing (3CC10752ABAA) ................................................28
Table 2 - ODU Mounting Hardware Installation Kit Listing (3CC10752ABAB) ................................................29
Table 3 Cable Grounding Kit .........................................................................................................................30
Table 4 Non Integrated pole mounting installation kit ...................................................................................33
Table 5 Cable Grounding Kit .........................................................................................................................33
Table 6 9470 AWY - ODU Installation materials for Integrated or Non Integrated antenna cases...............37
Table 7 9413 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases................38
Table 8 9415 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases................39
Table 9 9418 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases................40
Table 10 9423 AWY - ODU Installation materials for Integrated or Not Integrated antenna case................41
Table 11 9425 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases..............42
Table 12 9428 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases..............43
Table 13 9438 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases..............44
Table 14 - IDU Installation components ...........................................................................................................45
Table 15 - 7-8Ghz FLEXTWIST WAVEGUIDE ................................................................................................83
Table 16 - 13-38Ghz FLEXTWIST WAVEGUIDE ............................................................................................83
Table 17 - AWY 7/8 GHz Installation code Full Indoor housing kit ..................................................................93
Table 18 - Numbering and functions referred to the Connection Points (Main).............................................117
Table 19 - Numbering and functions referred to the Connection Points (Extension).....................................118
Table 20 - Numbering and functions referred to the Connection Points (1+1 version)..................................119
Table 21 - Suggested cabling.........................................................................................................................121
Table 22 - I/O (1 through 8) connections........................................................................................................126
Table 23 - I/O (9 through 16) connection .......................................................................................................126
Table 24 Distributor Subrack and Cable type..............................................................................................127
Figures
Figure 1 ODU 13-38 GHz rear and front views .............................................................................................19
Figure 2 - ODU 7-8 GHz rear and front views ..................................................................................................19
Figure 3 - ODU solar shields views (13 to 38GHz) ..........................................................................................20
Figure 4 - ODU solar shields views (7- 8GHz) .................................................................................................21
Figure 5 - ODU RF coupler view (Bands from 13 to 38 GHz) ........................................................................22
Figure 6 - ODU RF coupler view (Bands 7- 8 GHz) ........................................................................................23
Figure 7 - ODU RF coupler view (Bands 7- 8 GHz) ........................................................................................24
Figure 8 - IDU 9400 AWY 1+0.........................................................................................................................25
Figure 9 - IDU 9400 AWY 1+1.........................................................................................................................25
Figure 10 - Telephone set ...............................................................................................................................26
Figure 11 Not integrated antenna and ODU Mounting Hardware Installation Kit .........................................32
Figure 12...........................................................................................................................................................32
Figure 13 Integrated POLE MOUNTING View ..............................................................................................34
Figure 14 RADIO and NON Integrated ANTENNA CABINET GROUNDING KIT View ...............................34
Figure 15 - 13-38GHz ODU rear and front views.............................................................................................47
Figure 16 7-8 GHz ODU rear and front views ...............................................................................................48
Figure 17 D-BOX and A-BOX Integration......................................................................................................49
Figure 18 - Typical installation of 1+0 ODU with integrated antenna, 30 cm or 60 cm....................................51
Figure 19 - Typical installation of 1+1 ODU with integrated antenna, 30 cm or 60 cm....................................52
Figure 20 - Typical install. of 1+0 ODU with non integrated antenna and the 600 mm. ..................................53
Figure 21 - Typical install. of 1+1 ODU with non integrated antenna and the 600 mm. flexible twist or
optimized Wave-guide length ..................................................................................................................54
Figure 22 - Integrated pole mounting with ODU 1+0, Horizontal Polarization .................................................55
Figure 23 - Integrated antenna pole mounting with ODU 1+0, Vertical Polarization .......................................56
Figure 24 7-8 GHz Integrated antenna pole mounting with ODU 1+0, Vertical Polarization ........................57
Figure 25 - Pole mounting installation for integrated antenna..........................................................................58
Figure 26 - Change polarisation description.....................................................................................................59
Figure 27 - Installation with integrated antenna and Vertical polarization........................................................59
Figure 28 - ODU 1+0 installation for integrated antenna..................................................................................60
Figure 29 Pole mounting types......................................................................................................................61
Figure 30 Stretching screw (3CC14292AAAA) ............................................................................................61
Figure 31 Pole mounting without Stretching screw inserted ........................................................................62
ED 05
3DB 06687 DAAA
5/178
Figure 32 Stretching screw inserted (Vertical alignment) .............................................................................62
Figure 33 Integrated pole mounting (Horizontal alignment).........................................................................63
Figure 34 - Pole mounting near a wall .............................................................................................................64
Figure 35 3 Feet Antenna (Configuration 1+0) .............................................................................................65
Figure 36- 4 Feet Antenna (Configuration 1+0) ...............................................................................................66
Figure 37 - Typical installation pole mounting with ODU 1+1 for integrated antenna......................................67
Figure 38 - Installing the Coupler To the Radio Support..................................................................................68
Figure 39 - Installing the RF coupler with ODU 1+1 for integrated antenna....................................................69
Figure 40 1st Step and 2nd step .....................................................................................................................70
Figure 41 1st Step inserted ..........................................................................................................................70
Figure 42 2nd Step inserted ..........................................................................................................................71
Figure 43 Screws fixing.................................................................................................................................71
Figure 44 - Typical installation pole mounting with ODU 1+1 for integrated antenna (7-8GHz)......................72
Figure 45 - Installing the Coupler To the Radio Support..................................................................................73
Figure 46 - Installing the RF coupler with ODU 1+1 for integrated antenna....................................................74
Figure 47 7 8GHz Change Polarization .....................................................................................................75
Figure 48 - Typical installation pole mounting with ODU 1+1 for integrated antenna (7-8GHz)......................76
Figure 49 7- 8GHz Coupler (Alternative B) ...................................................................................................77
Figure 50 - Installing the Coupler To the Radio Support..................................................................................77
Figure 51 - Installing the RF coupler with ODU 1+1 for integrated antenna....................................................78
Figure 52 7 8GHz Change Polarization .....................................................................................................79
Figure 53 - Pole mounting installation for not integrated antenna with ODU 1+0............................................80
Figure 54 - Installation of the pole mounting for not integrated antenna .........................................................81
Figure 55 - ODU 1+0 installation for not integrated antenna ...........................................................................82
Figure 56 - Pole mounting with ODU 1+1 for not integrated antenna (13 to 38 GHz) .....................................84
Figure 57 - Installation of the Coupler on the pole mounting (13 to 38 GHz) ..................................................85
Figure 58 - Installation of ODU 1+1 on the pole mounting for not integrated antenna (11 to 38 GHz) ...........85
Figure 59 - Pole mounting ODU 1+1 for not integrated antenna .....................................................................86
Figure 60 - Pole mounting ODU 1+1 for not integrated antenna .....................................................................86
Figure 61 - Pole mounting/RF COUPLER 1+1 for not integrated antenna (7 - 8GHz) ....................................88
Figure 62 - Installation of ODU 1+1 on the pole mounting for not integrated antenna (7- 8 GHz) ..................89
Figure 63 Panel support 4U 19 for ODU 1+1 and Coupler.......................................................................90
Figure 64 Panel support 4U 19 for ODU 1+1 and Coupler.......................................................................91
Figure 65 Principle Installation in Laborack with ODU 1+1 and Coupler......................................................92
Figure 66 Support pole mounting (Laborack) ...............................................................................................93
Figure 67 - Pole mounting ODU 1+1 for not integrated antenna (7 - 8GHz) ...................................................94
Figure 68 - Pole mounting/RF COUPLER 1+1 for not integrated antenna (7 - 8GHz) ....................................95
Figure 69 - Installation of ODU 1+1 on the pole mounting for not integrated antenna (7- 8 GHz) ..................96
Figure 70 - Solar shield installation ODU 1+0..................................................................................................97
Figure 71 - Example of 1+0 and 1+1 IDU with 21" supports for rack mounting.............................................101
Figure 72 - Subrack installation in 21" rack....................................................................................................102
Figure 73 View of installation .......................................................................................................................103
Figure 74 - Wired mini distributor ...................................................................................................................103
Figure 75 - Laborack ......................................................................................................................................104
Figure 76 - IDU adapter for installation ..........................................................................................................105
Figure 77 - Subrack cabinets grounding points .............................................................................................106
Figure 78 - Minimum distances for dense packing in both systems (1+0 and 1+1) ......................................108
Figure 79 Summary of minimum distance in 1+0 and 1+1 configuration....................................................108
Figure 80 - Fixing the mechanical support to the wall....................................................................................109
Figure 81 Main Unit Front ...........................................................................................................................110
Figure 82 Extension Unit Front ....................................................................................................................110
Figure 83 - Main Front / Rear view interconnections IDU .............................................................................112
Figure 84 Main Rear view (Flash card insertion) .......................................................................................112
Figure 85 - Extension Front view interconnections IDU.................................................................................113
Figure 86 - Extension Rear view IDU.............................................................................................................113
Figure 87 1+0 Interconnections view ..........................................................................................................114
Figure 88 1+1 Interconnection view (8E1) ..................................................................................................115
Figure 89 1+1 Interconnection view (16E1) ................................................................................................115
Figure 90 Interconnection view (E3) ...........................................................................................................116
Figure 91 Interconnection view (Ethernet ...................................................................................................116
Figure 92 E1 / DS1 and User Service Channel Split-Cable........................................................................122
Figure 93 Cable connections (example) .....................................................................................................123
Figure 94-1+1 Inter-connection......................................................................................................................124
Figure 95 - I/O 1 through 8 and 9 through16 connections (Main Extension) ..............................................125
Figure 96 - NMS V11 Audio1 (EOW) connections......................................................................................128
Figure 97 - NMS_G703 + Audio2 (EOW) connections ..................................................................................129
ED 05
3DB 06687 DAAA
6/178
Figure 98 NMS INTERFACE AWY-MELODIE ............................................................................................130
Figure 99 - SERVICE CHANNEL connections (Main Extension)................................................................131
Figure 100 - Housekeeping- Alarms- connections .........................................................................................132
Figure 101 - E3 DS3 Interface connections (Main Extension) ....................................................................133
Figure 102 - M, LT and LEDs meanings ........................................................................................................134
Figure 103 OS - DEBUG connections cable pin out table ..........................................................................135
Figure 104 - CT connections ..........................................................................................................................136
Figure 105 - IDU ODU interconnections (Main Extension) .........................................................................138
Figure 106 - Details for assembling N connector to coaxial cable...............................................................139
Figure 107 Power Supply Connector ..........................................................................................................141
Figure 108 - Power supply connections .........................................................................................................142
Figure 109 ON-OFF Switch .........................................................................................................................142
Figure 110 - Fixing the W.T.D. rack using expansion anchors ......................................................................145
Figure 111 - rack - Drill Holes for Anchoring to the Floor (single rack) ..........................................................146
Figure 112 - rack - Floor tile drilling template .................................................................................................147
Figure 113 - rack - Example of securing rack assembly to computer floor ....................................................148
Figure 114 - rack - T.R.U. fastening to the rack .............................................................................................149
Figure 115 - W.T.D rack - Front plate 6 circuit breakers ................................................................................149
Figure 116 - Rack - Ground connections .......................................................................................................150
ED 05
3DB 06687 DAAA
7/178
1. HANDBOOK GUIDE
1.1.
Copyright notification
The technical information of this manual is property of ALCATEL and must not be copied, reproduced or
disclosed to a third party without written consent.
1.2.
Notice
The product specification and/or performance levels contained in this document are for information
purposes only and are subject to change without notice. They do not represent any obligation on the part of
ALCATEL.
1.3.
9400AWY Rel.2.0 Customer Documentation set
The standard Customer Documentation for 9400AWY Rel.2.0 is in the English language and is distributed
to Customers only by the following CD-ROM:
CD-ROM Technical Description
DCP 9400AWY 2.0 CD_ROM
Technical Code
3DB 06687 AAAA
Commercial Code
3EJ 14535 AAAA
It contains, in electronic format (ADOBE ACROBAT pdf files), the following handbooks:
-
9400AWY Rel.2.0 Installation Handbook (this handbook) (V2.0.0 to V2.0.4)
Provides information regarding equipment hardware installation, according to Alcatel WTD LAB. rules.
9400AWY Rel.2.0 User Manual (V2.0.4 only)
Provides information regarding 9400AWY Rel.2.0 running with SWP 9400AWY IDU16 V2.0.4 & TCO
Suite:
equipment description and composition, station layouts and hardware setting documentation and
maintenance
SWP screens and operational procedures for Equipment SW management and maintenance
equipment commissioning, according to Alcatel WTD LAB rules
9400AWY Rel.2.0 TRS and SAT (V2.0.4 only)
Contains the Test Report Sheet and the Site Acceptance Test protocol, according to Alcatel WTD LAB
rules. The source file of this document (MSWORD 2000) is also distributed in the Documentation CDROM
9400AWY Rel.2.0 Line-up Guide (V2.0.0 to V2.0.3)
Provides information regarding equipment line up and commissioning, according to Alcatel WTD LAB.
rules.
9400AWY Rel. 2.0 Technical Handbook (V2.0.0 to V2.0.3)
Provides detailed information regarding 9400AWY equipment description, composition and
provisioning, station layouts, item technical and commercial codes, and maintenance procedures.
9400AWY Rel.2.0 SWP 2.0 CT Operators Handbook (V2.0.0 to V2.0.3)
Provides 9400AWY SWP screens and operational procedures for equipment SW management and
maintenance.
Interference investigation procedure (Version independent)
Describes the measurement procedure for the interference searching in the various RF bands used by
Alcatel Radio Transmission products. It is common to all Alcatel Radio Transmission products.
ED 05
3DB 06687 DAAA
8/178
For further information regarding 9400AWY Rel.2.0 Customer Documentation set, please refer to the
document Customer Documentation set description and CD-ROM history accessible from the CDROM MAIN MENU.
ED 05
3DB 06687 DAAA
9/178
1.4.
History, applicability and purpose of this manual
05
08/11/2006
00000 34899
P.GAROFOLI
C.NAVA
04
24/05/2006
00000 33338
P.GAROFOLI
C.NAVA
03
03/02/2006
00000 20169
P.GAROFOLI
C.NAVA
02
09/11/2005
00000 23752
A.BESTETTI
C.NAVA
01
24/05/2005
R.VALTOLINA
C.NAVA
ED
DATE
APPRAISAL
AUTHORITY
ORIIGINATOR
CHANGE NOTE
This handbook is associated to SWP 9400AWY Rel.2.0.x, taking into account all system features that
are made available by first SWP version V2.0.0, as well as by successive SWP releases-versions. This
table sums-up the major additional features (mainly related to new HW items and relevant performance)
that are available starting from a certain SWP-version successive to first SWP version V2.0.0.
Additional feature
New 48/60V and 24V PSU ETSI IDU Main and Extension units, with
different
3DB xxxxx AX** P/N ( with X > A )
(refer to Technical Handbook for details)
7-8 GHz ODUs (new 9470AWY product) N.B.
Available from
SWP-version
mandatory
from V2.0.1
V2.0.2
New full-range (24-60V) IDU Main and Extension units N.B.
ANSI version (DS1/DS3) interfaces and relevant ANSI IDU Main and
Extension units and Plug-Ins N.B.
ANSI version ODUs N.B.
V2.0.3
New 1338 GHz ODUs with variable shifter N.B.
Refer to Technical Handbook from ED.04 for details
Removed functionality restrictions of the Remote Craft Terminal in
OSPF Stub areas
Possibility of configuring a Default Gateway Routing
Refer to Operators Handbook from ED.04 or User Manual for details
V2.0.4
ODU 32E1
N.B. the claimed item management must be meant from SWP-version point of view, independently from
actual availability of related HW items. Refer to User Manual/Technical Handbook for details.
WARNING
ED 05
Ed.05 of this handbook is validated in conjunction with SWP versions V2.0.0 to V2.0.4
only. Information relevant to SWP versions > V2.0.4, if any, must be considered preliminary,
subject to change and without any obligation on the part of ALCATEL.
3DB 06687 DAAA
10/178
1.5.
Handbook history, scope and related documents
ED
DATE
COMMENTS
01
24/05/2005
First Edition for R2.0.0
02
09/11/2005
Second Edition for R2.0.0 to R.2.0.1, and corrections.
03
03/02/2006
04
24/05/2006
05
08/11/2006
Third Edition for R2.0.0 to R.2.0.2, and corrections.
Draft editions neither validated nor officially released issue, for internal
validation purposes:
21/04/2006 : ED04A First draft edition
Fourth Edition for R2.0.0 to R.2.0.3, and corrections.
Draft editions neither validated nor officially released issue, for internal
validation purposes:
ED05A First draft edition
Fifth Edition for R2.0.0 to R.2.0.4, and corrections
The scope of this document is to provide the user with the information needed to install the hardware
components of an equipment of the 9400AWY Rel.2.0 family:
mechanical installation of the INDOOR and OUTDOOR units
mechanical installation and pre-positioning of the anntenna(s)
allocation (but not the connection) of the IDU-ODU IF cable.
Notice that the subsequent operations for the equipment activation are out of the scope of this document.
For this purpose refer to the User Manual/Line-Up Guide.
Take into account that this handbook does not contain the following bits of information:
detailed equipment Technical Characteristics
item Commercial Codes
equipment description, at various levels
detailed safety instructions
that you can find in the User Manual/Technical Handbook.
To easily find such information, or any other information you may need (and that is not included in this
handbook), please refer to the document Documentation Quick Guide accessible from the CD-ROM
MAIN MENU.
ED 05
3DB 06687 DAAA
11/178
2. SYSTEM TECHNICAL CHARACTERISTICS
2.1.
-
2.2.
System temperature condition tolerated
Storage condition
Transport condition
Working condition
ETS 300.019 class 1.3
ETS 300.019 class 2.3
IDU - from -5C to +55C
ODU - from -33C to +55C
System Voltage working condition
DC nominal voltage
+/- 48 to +/- 60 Vdc +/-20%
+/- 24 Vdc -20% +50%
Polarity = + or floating ( isolated ground)
System Consumption Sys. 1+0 <=40W
Sys. 1+1 <=80W
ED 05
3DB 06687 DAAA
12/178
2.3.
System Mechanical characteristics
ODU
IDU 1+0
IDU 1+1
weigth
3.9kg
weight 2.5 kg IDU 1+0
weight 4.0.kg IDU 1+1
Dimension
Dimension
Dimension
235X 235X 72 mm
44,45X 210X443 mm
89,9X210X443 mm
(1U)
(2U)
Couplers dimensions and weight:
Coupler 7-8Ghz
1AB228950005
1AB340390001
weight 6kg
weight 6kg
Dimensions
Dimensions
521x235x121 mmm
286,4x342,4x235 mm
Coupler 13-38Ghz
3CC13474ABAA
weight 4,3kg
Dimensions
341x234x234 mm
For more information, please refer to the User Manual/Technical Handbook, chapters:
Technical Specifications
ODU and antenna configurations, part lists and provisioning, paragraph ODU mechanical design and
identification
ED 05
3DB 06687 DAAA
13/178
3. INSTALLATION RULES
ATTENTION
EMC NORMS
WHEN CARRYING OUT THE GIVEN OPERATIONS OBSERVE THE NORMS STATES IN
RELATIVE CHAPTER IN USER MANUAL/ TECHNICAL HANDBOOK
3.1.
Safety Rules
Detailed Safety Rules are given in User Manual/Technical Handbooks. They describe the operations
and/or precautions to observe to safeguard operating personnel during the working phases and to
guarantee equipment safety.
Please read them with accuracy before to start every action on the equipment.
SAFETY RULES
Carefully observe the front-panel warning labels prior to working on
optical connections while the equipment is in-service.
3.2.
General Rules
Check that the equipment is operating with all the shields properly positioned (dummy covers, ESD
connector protections, etc.)
Carefully observe the front-panel warning labels prior to working on optical connections while the
equipment is in-service
In order to reduce the risk of damage the electrostatic sensitive devices, is mandatory to use the
elasticized band (around the wrist) and the coiled cord joined connect with the ground rack during the
touching of the equipment.
All the measures must be done at the MDF/CDF points (MDF= Mini Distributor Frame, CDF=
Customer Distributor Frame).
The equipment may be installed only in RESTRICTED ACCESS LOCATIONS, and be permanently
connected to a PROTECTIVE EARTHING CONDUCTOR as described in the Installation section.
Equipotential bonding must be applied for all equipments in the location.
ED 05
3DB 06687 DAAA
14/178
3.3.
EMF safety instructions
Equipment emitting RF power (Reminder from site preparation procedure):
-
The site must be compliant with ICNIRP guidelines or local regulation if more restrictive.
The following rules should be strictly applied by Customer:
None authorized persons should not enter the compliance boundaries, if any, for the general
public.
Compliance RF boundaries, if any, related to Electro Magnetic Field exposure must be marked.
Workers should be allowed to switch-off the power if they have to operate inside compliance
boundaries.
Assure good cable connection.
Install the antenna as high as possible from floor or area with public access (if possible the
cylinder delimitating the compliance boundaries, if any, or the cylinder corresponding to the
transmission area directly in front of antenna with the same diameter as the antenna, more than
2
meters high).
Install the antenna as far as possible from other existing equipment emitting RF power.
Anyway remind that someone standing in front of the 9400AWY antenna may cause traffic
shutdown
Place the relevant stickers:
On the site when applicable (when people can cross the compliance boundaries
and/or the transmission area of the antenna, i.e. roof top installation)
Warning label Do not stand on the antenna axis
EMF EMISSION
On the mast (front side)
EMF emission warning sign (Yellow and black) to be placed at bottom of
antenna, visible by someone moving in front of the antenna (roof top installation)
WARNING SIGN
On the antenna (rear side)
EMF emission warning sign, placed on the antenna.
ED 05
3DB 06687 DAAA
15/178
3.4.
Unpacking and Warehousing
3.4.1.
General
The following procedures have been issued and must be observed when unpacking the equipment. The
reciprocal operation must be done for repacking. In such case it is recommended to use the original
packing material.
The following sturdy outer packing material is utilized in order to protect the equipment against mechanical
and climatic stresses to which they are subjected:
wooden crates
for transport by ship, air, on road for periods longer than 60 days
ply-wood crates
for transport by ship, air, on road for periods of 30 to 60 days
cardboard boxes
for transport by air or on road for periods of less than 30 days
3.4.2.
Unpacking
PRELIMINARY CHECKS
The following information should be printed on the outer crate:
International symbols
side up :
keep dry
fragile
trade mark/address of the manufacturing company;
labels (or template marks) indicating information on the contract and destination site of the
product;
an envelope holding among others the packing list
Upon receipt check:
that the final destination of the crates is that indicated on the label;
that no damage was made to the cases
Report any shipping damages to the Companys representative or the Shipping Agent.
UNPACKING
When having to unpack proceed as follows:
symbol
make sure that the packing has been properly positioned, refer to the
open the case;
remove the shockproof material;
remove the goods from the case;
remove prepacking, the polyethylene bag and any other protection;
remove the plastic bags cello taped to the rack and containing accessories;
remove the dehydrating bags;
ascertain that the goods are not damaged and that they correspond to those indicated on the
packing list enclosed in the envelope. Conversely, contact the agencys representative.
N.B. When unpacking it is advisable to handle the packing material with care; it might be reused for
packing again if it must be reshipped.
ED 05
3DB 06687 DAAA
16/178
3.4.3.
Warehousing
If having to store the packed material, the following requirements must be met:
the cardboard boxes must be placed indoor in airy rooms;
the wooden or plywood cases can be placed outdoors provided they are protected against rain
and direct sunlight.
3.5.
Pre-Installation Checking
CRATE CONTENTS CHECK
Check the contents of the shipping crates for the following configurations:
3.5.1.
-
IDU - BB 1+0 (Telephone Kit if present in site)
ODU RTx & solar shield
Integrated Pole Mounting
Fixing Installation kit material
Antenna
IDU / ODU Cable & Connectors
Installation kit material
Subrack for BB Wall installation ( if foreseen by Plant Documentation)
Rx Power Monitoring & Light Service Kit Cable
3.5.2.
-
1+0 Integrated Antenna
1+0 NON Integrated Antenna
IDU - BB 1+0 (Telephone Kit if present in site)
ODU RTx & solar shield
Non Integrated Pole Mounting
Antenna Support
Fixing Installation kit material
Antenna
Flex Twist / Wave guide and Wave Guide Connectors
IDU / ODU Cable & Connectors
Installation kit material
Subrack for BB Wall installation ( if foreseen by Plant Documentation )
Rx Power Monitoring & Light Service Kit Cable
ED 05
3DB 06687 DAAA
17/178
3.5.3.
-
IDU - BB 1+1 (Telephone Kit if present in site)
N2 ODU RTx & solar shield
RF Coupler
Integrated Pole Mounting
Fixing Installation kit material
Antenna
IDU / ODU Cable & Connectors
Installation kit material
Subrack for BB Wall installation ( if foreseen by Plant Documentation )
Rx Power Monitoring & Light Service Kit Cable
3.5.4.
-
1+1 Integrated Antenna
1+1 NON Integrated Antenna
IDU - BB 1+1 (Telephone Kit if present in site)
Fixing Installation kit material
N2 ODU RTx & solar shield
RF Coupler
Non Integrated Pole Mounting
Antenna Support
Antenna
Flex Twist / Wave guide and Wave Guide Connectors
IDU / ODU Cable & Connectors
Installation kit material
Subrack for BB Wall Installation ( if foreseen by Plant Documentation )
- Rx Power Monitoring & Light Service Kit Cable
ED 05
3DB 06687 DAAA
18/178
3.5.5.
OUTDOOR UNITS CHECK
Figure 1 ODU 13-38 GHz rear and front views
A-BOX
D-BOX
Figure 2 - ODU 7-8 GHz rear and front views
ED 05
3DB 06687 DAAA
19/178
ODU Solar Shield P/N - 3CC13476AAAA
Screws
1+0 ODU solar shield view
1+1 ODU solar shields view
Figure 3 - ODU solar shields views (13 to 38GHz)
ED 05
3DB 06687 DAAA
20/178
1+1 ODU solar shields view
Figure 4 - ODU solar shields views (7- 8GHz)
ED 05
3DB 06687 DAAA
21/178
3.5.6.
RF COUPLER UNIT CHECK
CH 0 Side
CH 1 Side
Figure 5 - ODU RF coupler view (Bands from 13 to 38 GHz)
ED 05
3DB 06687 DAAA
22/178
Main
Acess
Figure 6 - ODU RF coupler view (Bands 7- 8 GHz)
ED 05
3DB 06687 DAAA
23/178
MAIN
MAIN
Figure 7 - ODU RF coupler view (Bands 7- 8 GHz)
ED 05
3DB 06687 DAAA
24/178
ODU RF coupler Reference P/N
3.5.7.
1AB228950005
7.1-8.5 GHz 10dB Coupler
1AB340390001
7.1-8.5 GHz 10dB Coupler
3CC13472ABAA
13/15 GHz 10dB Coupler
3CC13473ABAA
18/23/25 GHz 10dB Coupler
3CC13474ABAA
28/38 GHz 10dB Coupler
INDOOR UNIT TYPES CHECK
MAIN
Figure 8 - IDU 9400 AWY 1+0
EXTENSION
MAIN
Figure 9 - IDU 9400 AWY 1+1
ED 05
3DB 06687 DAAA
25/178
Set switch to DTMF
RJ11
connector
ON/OFF switch
(Telephone 3CC07946AAAA)
RJ 11 connector
(Telephone 1AF12831AAAA)
Figure 10 - Telephone set
ED 05
3DB 06687 DAAA
26/178
3.5.8.
INTEGRATED POLE MOUNTING INSTALLATION HARDWARE KIT CHECK
Check contents of all hardware bags according to the following Hardware installation Kits:
-
1+0 Integrated Antenna and ODU Mounting
Hardware Installation Kit
1+1 Integrated Antenna and ODU Mounting
Hardware Installation Kit
RF coupler - No Installation Hardware Kit is required for RF Coupler
1A
1
13 38 GHz
1B
1B
1AB340390001
1AB228950005
7 8GHz
ED 05
3DB 06687 DAAA
27/178
Integrated Pole Mounting
Fine tuning
Table 1 - ODU Mounting Hardware Installation Kit Listing (3CC10752ABAA)
DESCRIPTION
CODE
ODU RF coupler (13-38 GHz)
PHOTO
REF
INTEG.
ANT. 1+0
quantity
INTEG.
ANT. 1+1
quantity
1A
ODU RF coupler (7-8GHz)
1AB340390001
1B
ODU RF coupler (7-8GHz)
1AB228950005
1B
Pole Mounting for Integrated
3CC10752ABAA
Screw*CH-HD*HEX-SKT M6x20mm
Washer*Waved
6.4mmx12mmx500/M6
Screw*CH-HD*HEX-SKT 10x25mm
NUT*HEX*HEX*-HD
M6x5.2mm
NUT*HEX*HEX*-HD
M10x8.4mm
Washer*Plain
6.4mmx14mm1.2mm/M6
Washer*Waved
10.5mm21mm1mm/M10
Washer*Waved
10.5mm22mm1mm/M10
Screw*CH-HD*HEX-HEX-HD
1AD002150071
1AD002290017
1AD002150100
1AD001970033
1AD001970046
1AD000870170
1AD002290005
1AD00870185
11
11
1AD000500064
2G8 9438UXVIS (POUR RIDOIR)
3CC10816AAAA
2G0 9400UXVIS (POUR RIDOIR)
3CC11577AAAA
2G8 9438UXRIDOIR (POUR RIDOIR)
3CC1085AAAA
2G8 9438UXENTRETOISE
3CC10894AAA
NUT*HEX*HEX*-HD
M10x6.8mm
Washer*SC-SPG
10.5mm16.5mmx1.8mm/M10
2G0 9400UXETRIER (CLAMP)
1AD001970021
1AD011670004
3CC06029AAAA
1AD001970046
NUT*HEX*HEX*-HD
M10x6.8mm
ADHESIVE, DIMETHYLACRYLAT
ED 05
1AC008760001
3DB 06687 DAAA
28/178
Without
Fine tuning
Table 2 - ODU Mounting Hardware Installation Kit Listing (3CC10752ABAB)
DESCRIPTION
CODE
ODU RF coupler (13-38 GHz)
PHOTO
REF
INTEG.
ANT. 1+0
quantity
INTEG.
ANT. 1+1
quantity
1A
ODU RF coupler (7-8GHz)
1AB340390001
1B
ODU RF coupler (7-8GHz)
1AB228950005
1B
Pole Mounting for Integrated
3CC10752ABAA
Screw*CH-HD*HEX-SKT M6x20mm
Washer*Waved
6.4mmx12mmx500/M6
Screw*CH-HD*HEX-SKT 10x25mm
NUT*HEX*HEX*-HD
M6x5.2mm
NUT*HEX*HEX*-HD
M10x8.4mm
Washer*Plain
6.4mmx14mm1.2mm/M6
Washer*Waved
10.5mm21mm1mm/M10
Washer*Waved
10.5mm22mm1mm/M10
Screw*CH-HD*HEX-HEX-HD
Washer*SC-SPG
10.5mm16.5mmx1.8mm/M10
2G0 9400UXETRIER (CLAMP)
NUT*HEX*HEX*-HD
M10x6.8mm
1AD002150071
1AD002290017
1AD002150100
1AD001970033
1AD001970046
1AD000870170
1AD002290005
1AD00870185
11
11
1AD000500064
1AD011670004
3CC06029AAAA
1AD001970046
See Table 1 - ODU Mounting Hardware Installation Kit Listing (3CC10752ABAA) on page 28 and Table 2ODU Mounting Hardware Installation Kit Listing (3CC10752ABAB) on page 29 for a description of the
items shown in the photograph.. All parts shown should be received packed together in the same carton.
The steerable support is wrapped and the remaining hardware is in two plastic bags, the large pieces in a
large plastic bag and the smaller hardware in a small plastic bag within the larger bag.
ED 05
3DB 06687 DAAA
29/178
3.5.8.1. Cable Grounding Kit
Cable Groundig Kit 3CC08166ABAA (16mm2 L=15m) to be cut on site and clamped on the terminal
provided with the pole mounting
Table 3 Cable Grounding Kit
DESCRIPTION
CODE
Cable Power 196*16MM2
1AC001060066
Washer*Plain 6.4mm x 14mm x 1.2mmm/M6
1AD000870170
Lug*Ring*Crimp*Uninsul 4.51mm
1AB032050033
Screw*CH-HD*HEX-SKT M6x20mm
1AD002150071
Nut*HEX*HEX-HD M6x5.2MM
1AD001970033
ED 05
Q.ty
1 (L=15m)
3
6
3
3
3DB 06687 DAAA
30/178
3.5.9.
NON INTEGRATED ANTENNA POLE MOUNTING INSTALLATION HARDWARE KIT CHECK
Check contents of all hardware bags according to the following Hardware installation Kits:
-
1+0 NON Integrated Antenna and ODU Mounting Hardware Installation Kit
1+1 NON Integrated Antenna and ODU Mounting Hardware Installation Kit
RF coupler
No Installation Hardware Kit is required for RF Coupler
13 38GHz
1A
1AB340390001
1AB228950005
7 8 GHz
ED 05
3DB 06687 DAAA
31/178
Pole mounting for NOT INTEGRATED antenna
3DB10137AAAA
NON Integrated pole mounting Installation Hardware Kit
3
Clamp
Support tube
Washer Plain
Washer*SC-SPG
Nut*HEX*HEX-HD
Support
Pole Mounting
Washer*SC-SPG
Nut*HEX*-HEX-HD
Screw*HEX-HD*HEX-HD
Figure 11 Not integrated antenna and ODU Mounting Hardware Installation Kit
Figure 12
ED 05
3DB 06687 DAAA
32/178
See Table 4 on page 33 for a description of the items shown in the Figure 11 on page 32. All parts
shown should be received packed together in the same carton. The steerable support is wrapped and the
remaining hardware is in two plastic bags, the large pieces in a large plastic bag and the smaller hardware
in a small plastic bag within the larger bag.
Table 4 Non Integrated pole mounting installation kit
INSTALLATION KIT
DESCRIPTION
CODE
PHOTO
REF
ODU RF coupler (13-38 GHz)
ODU RF coupler (7-8GHz)
ODU RF coupler (7-8GHz)
Pole mounting for NOT INTEGRATED
antenna
Support Pole Mounting
NON
NON
INTEG.
ANT. 1+0
INTEG.
ANT. 1+1
quantity
quantity
1AB228950005
1AB340390001
1A
1A
3DB10137AAAA
3DB10138AAAA
Support tube
3CC13037AAAA
9400UXETRIER (CLAMP)
3CC06029ABAA
Washer*Plain
10.5mmx22mmx2mm/M10
1AD000870185
Washer*SC-SPG
1AD011670004
1AD00190046
1AD002040083
1AC018650001
10.5mmx16.5mmx1.8mm/M10
Nut*Hex*Hex-HD
8.4mm/M10
Screw*Hex-HD*Hex-HD
M10x40mm*SS
Silicon Grease
Tube 5/8X2-3/16 (1.5cc)
3.5.9.1. Cable Grounding Kit
Cable Groundig Kit 3CC08166ABAA (16mm2 L=15m) to be cut on site and clamped on the terminal
provided with the pole mounting
Table 5 Cable Grounding Kit
DESCRIPTION
Cable Power 196*16MM2
Washer*Plain 6.4mm x 14mm x 1.2mmm/M6
Lug*Ring*Crimp*Uninsul 4.51mm
Screw*CH-HD*HEX-SKT M6x20mm
Nut*HEX*HEX-HD M6x5.2MM
ED 05
CODE
1AC001060066
1AD000870170
1AB032050033
1AD002150071
1AD001970033
Q.ty
1 (L=15m)
3
6
3
3
3DB 06687 DAAA
33/178
POLE MOUNT PARTS CHECK
Check for correct steering support and pole mount assembly according to the following:
Steering Support and Pole Mount Assembly for Radio with INTEGRATED ANTENNA
WARNING:
is mandatory to fix the four looking hooks like indicated and that is on the binary
inside
Ref: 3CC10752ABAA 3CC10752ABAB ODU and Integrated Antenna Cabinet grounding kit View
ODU Fixing point onto the Pole
Figure 13 Integrated POLE MOUNTING View
ODU Support and Pole Mount Assembly for Radio with NON-INTEGRATED ANTENNA
WARNING:
is mandatory to fix the four looking hooks like indicated and that is on the binary
inside
Ref: 1AB128510002 - ODU Support for NON Integrated Antenna POLE MOUNTING View
ODU Fixing point onto
the Pole
Figure 14 RADIO and NON Integrated ANTENNA CABINET GROUNDING KIT View
ED 05
3DB 06687 DAAA
34/178
3.6.
Installation Tools required
The 9400AWY system is supplied with three Tools Bag:
Station Tools Bag,
(P/N 3DB 01399 AAAA MSZZQ).
Maintenance Tools Bag (P/N 3DB 01398 AAAA MSZZQ).
Installation Tools Bag (P/N 3DB 01397 AAAA MSZZQ).
These documents are enclosures to the User Manual/Technical Handbook
3.7.
Tables of installation IDU-ODU components
The 9400 AWY composition catalogue includes also the installation components required for the most
common installation cases. The following tables shows the installation part list related to the available
system configuration and the antenna types.
3.7.1.
Integrated or Not Integrated antenna installation components
The following installation components tables include all the items required for the integrated antenna or Not
Integrated antenna cases, the tables show the item part numbers and the requested quantity related to the
foreseen system.
Note:
1In/N (2In/N) = it is possible to use INTEGRATED ANTENNA (In) or NON INTEGRATED ANTENNA (N)
1In (2In) =
it is possible to use INTEGRATED ANTENNA (In) only
1N (2N) =
it is possible to use NON INTEGRATED ANTENNA (N) only
Legend:
1+1 HST
1+1 Hot Stand-by
1+1 HST SD
1+1 Hot Stand-by Space Diversity
1+1 FD AP
1+1 Frequency Diversity Alternate Polar
1+1 FD DA
1+1 Frequency Diversity Dual Antenna
ED 05
3DB 06687 DAAA
35/178
9470 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Transceiver
3DB06691ABAA
3DB06692ABAA
3DB06693ABAA
3DB06694ABAA
Alcatel
part
number
3DB06774AAXX
3DB06774ABXX
3DB06775AAXX
3DB06775ABXX
3DB06776AAXX
3DB06776ABXX
3DB06777AAXX
3DB06777ABXX
3DB06778AAXX
3DB06778ABXX
3DB06779AAXX
3DB06779ABXX
3DB06780AAXX
3DB06780ABXX
3DB06781AAXX
3DB06781ABXX
3DB06782AAXX
3DB06782ABXX
3DB06783AAXX
3DB06783ABXX
3DB06784AAXX
3DB06784ABXX
3DB06785AAXX
3DB06785ABXX
3DB06786AAXX
3DB06786ABXX
3DB06787AAXX
3DB06787ABXX
3DB06788AAXX
3DB06788ABXX
3DB06789AAXX
3DB06789ABXX
3DB10060AAXX
3DB10059AAXX
3DB10073AAXX
3DB10073ABXX
Note:
A-
ED 05
Quantity / Configuration
Description
TRX 9470 7.1-7.75 GHZ LHB
TRX 9470 7.25-7. 9 GHZ LHB
TRX 9470 7.7-8.4 GHZ LHB
TRX 9470 8.0-8.5 GHZ UHB
1+0
1
1
1
1
Branching & Filters
1+0
BRANCHING 7GHZ CH1-1P P.SH. 154_A MHz
BRANCHING 7GHZ CH2-2P P.SH. 154_A MHz
BRANCHING 7GHZ CH1-1P P.SH.154_B/160 MHz
BRANCHING 7GHZ CH2-2P P.SH.154_B/160 MHz
BRANCHING 7GHZ CH1-1P P.SH.168 MHZ
BRANCHING 7GHZ CH2-2P P.SH.168 MHZ
BRANCHING 7GHZ CH1-1P P.SH.182 MHZ
BRANCHING 7GHZ CH2-2P P.SH.182 MHZ
BRANCHING 7GHZ CH1-1P P.SH.196 MHZ
BRANCHING 7GHZ CH2-2P P.SH.196 MHZ
BRANCHING 7GHZ CH1-1P P.SH.245 MHZ
BRANCHING 7GHZ CH2-2P P.SH.245 MHZ
BRANCHING 7GHZ CH1-1P P.SH.161_A MHz
BRANCHING 7GHZ CH2-2P P.SH.161_A MHz
BRANCHING 7GHZ CH1-1P P.SH.161_C MHz
BRANCHING 7GHZ CH2-2P P.SH.161_B MHz
BRANCHING 7GHZ CH1-1P P.SH.161_C MHz
BRANCHING 7GHZ CH2-2P P.SH.161_C MHz
BRANCHING 7GHZ CH1-1P P.SH.161_D MHz
BRANCHING 7GHZ CH2-2P P.SH.161_D MHz
BRANCHING 7GHZ CH1-1P P.SH.161_E MHz
BRANCHING 7GHZ CH2-2P P.SH.161_E MHz
BRANCHING 7GHZ CH1-1P P.SH.161_F MHz
BRANCHING 7GHZ CH2-2P P.SH.161_F MHz
BRANCHING 8GHZ CH1-1P P.SH.294/305/311 MHz
BRANCHING 8GHZ CH2-2P P.SH.294/305/311 MHz
BRANCHING 8GHZ CH1-1P P.SH.151 MHz
BRANCHING 8GHZ CH2-2P P.SH.151 MHz
BRANCHING 8GHZ CH1-1P P.SH.266 MHZ
BRANCHING 8GHZ CH2-2P P.SH.266 MHZ
BRANCHING 8GHZ CH1-1P P.SH.119/126 MHz
BRANCHING 8GHZ CH2-2P P.SH.119/126 MHz
BRANCHING 7GHZ CH1-1P P.SH.154_C MHZ
BRANCHING 7GHZ CH2-2P P.SH.168_B MHZ
BRANCHING 8GHZ CH1-1P P.SH208 MHZ
BRANCHING 8GHZ CH2-1P P.SH208 MHZ
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1+1
1+1
1+1
1+1
HST HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
(A)
2
2
2
2
(A)
(A)
(A)
1+1
1+1
1+1
1+1
HST HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Note
Note
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
ODU 32E1
3DB 06687 DAAA
36/178
9470 AWY - ODU INSTALLATION COMPONENTS
Alcatel
part
number
1AB228950005
3DB00677AAXX
1AB340390001
3DB00675AAXX
1AF11293AAAA
1AF11284AAAA
1AF11977AAAA
1AB128510002
3DB01459AAAA
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
Installation Materials
7.1-8.5 GHz 10dB Integrated Coupler
7GHz 2FT SP integrated antenna
7.1-8.5 GHz 10dB Integrated Coupler
8GHz 2FT SP integrated antenna
7.1-8.5 GHz 3FT Integrated antenna with PM
7.1-8.5 GHz 4FT Integrated antenna with PM
Flex Twist WR112 PDR84/UBR84 L=1m
Non Integrated Antenna Pole Mounting
Nose adapter WR112 kit for not int antenna
Integrated Pole Mounting for 1-2FT antenna
Integrated Pole Mounting for 1-2FT antenna
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N. 90 50 ohm
Cabinet grounding kit
Q.ty In = Integrated Antenna
1+0
1+1
1+1
1+1
1+1
Note
HST HST SD FD AP FD DA
1
1In
2In
2In
2In
2In
1
1In
1In
1In
1N
1In
1In
2N
1In
1In
2In
2In
2In
2In
Q.ty N= Not Integrated Antenna
Note: next introduction in substitution of actual configuration
Actual
Configuration
1AB128510002
3DB01459AAAA
1AF11977AAXX
Next introduction
Description
3DB10137AAXX
3DB10135AAAA
3CC08010ABAB
POLE MOUNTING NON INTEGRATED ANTENNA
WR112 ADAPTER KIT
Flex Twist WR112 PBR84/UBR84 L=1m
Table 6 9470 AWY - ODU Installation materials for Integrated or Non Integrated antenna cases
ED 05
3DB 06687 DAAA
37/178
9413 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Quantity / Configuration
Description
1+0
1+1
HST
1+0
1+1
HST
Coupler
3CC13472ABXX
Alcatel
part
number
13/15 GHz 10db Coupler
3CC13688ABAA
ODU 9413 fs=266MHZ 1-1
(A)
3CC13689ABAA
ODU 9413 fs=266MHZ 2-2
(A)
3CC13690ABAA
ODU 9413 fs=266MHZ 1-2
(A)
3CC13691ABAA
ODU 9413 fs=266MHZ 2-2
(A)
Installation Materials
1+0
1+1
HST
13 GHz 1FT SP INTEGR.ANTENNA ANDREW
13 GHz 2FT SP INTEGR.ANTENNA RFS
13 GHz 2FT SP INTEGR.ANTENNA ANDREW
13 GHz 3FT SP INTEGR.ANTENNA
13 GHz 4FT SP INTEGR.ANTENNA
13 GHz Flex Twist 600mm
Nose-Adapter (Non Integr.Antenna)
Non Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N.90 ohm 90
Cabinet grounding kit
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1N
1N
1In
1In
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1In
1In
Alcatel
part
number
1AF01893AAXX
1AF10018AAXX
1AF01894AAXX
1AF11285AAXX
1AF11482AAXX
3CC05751ACAA
1AB146090003
1AB128510002
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
Transceiver
Q.ty In = Integrated Antenna
Note:
A-
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
1N
1N
1N
1N
1N
2
2N
2N
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
Q.ty N= Not Integrated Antenna
ODU 32E1
Table 7 9413 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases
ED 05
3DB 06687 DAAA
38/178
9415 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Description
Coupler
Quantity / Configuration
1+1
HST
1+0
3CC13472ABXX 13/15 GHz 10db Coupler
Alcatel
part
number
3CC13704AAXX
3CC13705AAXX
3CC13706AAXX
3CC13707AAXX
3CC13696ABAA
3CC13697ABAA
3CC13698ABAA
3CC13699ABAA
3CC13700AAXX
3CC13701AAXX
3CC13702AAXX
3CC13703AAXX
3CC13704ABAA
3CC13705ABAA
3CC13706ABAA
3CC13707ABAA
3CC14077AAXX
3CC14078AAXX
3CC14079AAXX
3CC14080AAXX
3CC13708AAXX
3CC13710AAXX
3CC13692ABAA
3CC13693ABAA
3CC13694ABAA
3CC13695ABAA
3CC13709ABAA
3CC13711ABAA
3CC13712ABAA
3CC13713ABAA
Alcatel
part
number
1AF13287AAAA
1AF10018ABAA
1AF01892AAAA
1AF11285AAXX
1AF11482AAXX
3CC05750ACAA
1AB146090001
1AB128510002
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1+0
1+1
HST
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Installation Materials
1+0
1+1
HST
15 GHz 1FT SP AWY FULL INTEGRATED ANDREW
15 GHz 2FT SP INTEGR.ANTENNA RFS
15 GHz 2FT SP INTEGR.ANTENNA ANDREW
15 GHz 3FT SP INTEGR.ANTENNA
15 GHz 4FT SP INTEGR.ANTENNA
Flex Twist 15 GHz 600mm
Nose-Adapter (Non Integrated Antenna)
Non Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N.90 50 ohm
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1N
1N
1In
1In
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1In
1In
Transceiver
ODU 9415 fs=490MHz 1-1
ODU 9415 fs=490MHz 2-2
ODU 9415 fs=490MHz 1-1
ODU 9415 fs=490MHz 2-2
ODU 9415 fs=420MHz 1-1
ODU 9415 fs=420MHz 1-1
ODU 9415 fs=420MHz 2-2
ODU 9415 fs=420MHz 2-2
ODU 9415 fs=475MHz 1-1 HP
ODU 9415 fs=475MHz 1-1 HP
ODU 9415 fs=475MHz 2-2 HP
ODU 9415 fs=475MHz 2-2 HP
ODU 9415 fs=490MHz 1
ODU 9415 fs=490MHz 2
ODU 9415 fs=490MHz 1P
ODU 9415 fs=490MHz 2P
ODU 9415 fs=475MHz 1-1
ODU 9415 fs=475MHz 1-1
ODU 9415 fs=475MHz 2-2
ODU 9415 fs=475MHz 2-2
ODU 9415 fs=640MHz 1-1
ODU 9415 fs=640MHz 1-1
ODU 9415 fs=315MHz 1-1
ODU 9415 fs=315MHz 1-1
ODU 9415 fs=315MHz 2-2
ODU 9415 fs=315MHz 2-2
ODU 9415 fs=644MHz 1-1
ODU 9415 fs=644MHz 1-1
ODU 9415 fs=728MHz 1
ODU 9415 fs=728MHz 1P
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
1N
1N
1N
1N
1N
2
2N
2N
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
Cabinet grounding kit
Q.ty In = Integrated Antenna
Note:
AODU 32E1
Q.ty N= Not Integrated Antenna
Table 8 9415 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases
ED 05
3DB 06687 DAAA
39/178
9418 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Description
Coupler
3CC13473ABXX
Alcatel
part
number
3CC12991AAXX
3CC12992AAXX
3CC12993AAXX
3CC12994AAXX
3CC12999AAXX
3CC13000AAXX
3CC13001AAXX
3CC13002AAXX
3CC13947AAXX
3CC13948AAXX
3CC13468AAXX
3CC13469AAXX
3CC13470AAXX
3CC13471AAXX
3CC12995ABAA
3CC12996ABAA
3CC13714ABAA
3CC13715ABAA
3CC13716ABAA
3CC13717ABAA
3CC14472AAXX
3CC14473AAXX
3CC14474AAXX
3CC14475AAXX
3CC14780ABAA
3CC14781ABAA
3CC14782ABAA
3CC14783ABAA
Alcatel
part
number
1AF10018LAAAA
1AF13286AAAA
1AF10018ACAA
1AF13293AAAA
1AF11290AAXX
1AF11291AAXX
3CC05749ACAA
1AB146090002
1AB128510002
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
Quantity / Configuration
1+1
HST
1+0
18/23/245 GHz 10db Coupler
1
1+0
1+1
HST
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Installation Materials
1+0
1+1
HST
18 GHz 1FT SP INTEGR.ANTENNA RFS
18 GHz 1FT SP AWY FULL INTEGRATED ANDREW
18 GHz 2FT SP INTEGR.ANTENNA RFS
18 GHz 2FT SP AWY FULL INTEGRATED ANDREW
18 GHz 3FT SP INTEGR.ANTENNA
18 GHz 4FT SP INTEGR.ANTENNA
18/23/25 GHz Flex Twist
18/23/25 Nose-Adapter (Non Integr.Antenna)
Non Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N.90 50 ohm
Cabinet grounding kit
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1N
1N
1In
1In
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1In
1In
Transceiver
ODU 9418 fs=1010MHz 1-1
ODU 9418 fs=1010MHz 2-2
ODU 9418 fs=1010MHz 1-1
ODU 9418 fs=1010MHz 2-2
ODU 9418 fs=340MHz 1-1 ANSI
ODU 9418 fs=340MHz 1-1 ANSI
ODU 9418 fs=340MHz 2-2 ANSI
ODU 9418 fs=340MHz 2-2 ANSI
ODU 9418 fs=1560MHz 1-1 ANSI
ODU 9418 fs=1560MHz 1-1 ANSI
ODU 9418 fs=1008MHz 1-1
ODU 9418 fs=1008MHz 2-2
ODU 9418 fs=1008MHz 1-1
ODU 9418 fs=1008MHz 1-1
ODU 9418 fs=1560MHz 1-1 ETSI
ODU 9418 fs=1560MHz 1-1 ETSI
ODU 9418 fs=340MHz 1-1 ETSI
ODU 9418 fs=340MHz 2-2 ETSI
ODU 9418 fs=340MHz 1-1 ETSI
ODU 9418 fs=340MHz 2-2 ETSI
ODU 9418 fs=1092.5MHz 1-1
ODU 9418 fs=1092.5MHz 2-2
ODU 9418 fs=1092.5MHz 1-1
ODU 9418 fs=1092.5MHz 2-2
ODU 9418 fs=1008-1010MHz 1
ODU 9418 fs=1008-1010MHz 2
ODU 9418 fs=1008-1010MHz 1P
ODU 9418 fs=1008-1010MHz 2P
Q.ty In = Integrated Antenna
Note:
AODU 32E1
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2In/N
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
1N
1N
1N
1N
1N
1N
2
2N
2N
2In/N
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
Q.ty N= Not Integrated Antenna
Table 9 9418 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases
ED 05
3DB 06687 DAAA
40/178
9423 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Description
Coupler
3CC13473ABXX
Alcatel
part
number
3CC13718ABAA
3CC13719ABAA
3CC13720ABAA
3CC13721ABAA
3CC13722AAXX
3CC13723AAXX
3CC13724AAXX
3CC13725AAXX
3CC14388AAXX
3CC14389AAXX
3CC14390AAXX
3CC14391AAXX
3CC14400AAXX
3CC14401AAXX
3CC14402AAXX
3CC14403AAXX
3CC13726AAXX
3CC13727AAXX
3CC13728AAXX
3CC13729AAXX
3CC14776ABAA
3CC14777ABAA
3CC14778ABAA
3CC14779ABAA
Alcatel
part
number
1AF10018ADAA
1AF13285AAAA
1AF10018AEAA
1AF13292AAAA
1AF11292AAXX
1AF11288AXX
3CC05749ACAA
1AB146090002
1AB128510002
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
Quantity / Configuration
1+1
HST
1+0
18/23/245 GHz 10db Coupler
1
1+0
1+1
HST
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Installation Materials
1+0
1+1
HST
23 GHz 1FT SP INTEGR.ANTENNA RFS
23 GHz 1FT SP AWY FULL INTEGRATED ANDREW
23 GHz 2FT SP INTEGR.ANTENNA RFS
23 GHz 2FT SP AWY FULL INTEGRATED ANDREW
23 GHz 3FT SP INTEGR.ANTENNA
23 GHz 4FT SP INTEGR.ANTENNA
18/23/25 GHz Flex Twist
18/23/25 Nose-Adapter (Non Integr.Antenna)
Non Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N.90 50 ohm
Cabinet grounding kit
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1N
1N
1In
1In
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1In
1In
Transceiver
ODU 9423 fs=1008MHz 1-1
ODU 9423 fs=1008MHz 2-2
ODU 9423 fs=1008MHz 1-1
ODU 9423 fs=1008MHz 2-2
ODU 9423 fs=1200MHz 1-1 ANSI
ODU 9423 fs=1200MHz 1-1 ANSI
ODU 9423 fs=1200MHz 2-2 ANSI
ODU 9423 fs=1200MHz 2-2 ANSI
ODU 9423 fs=1200MHz 1-1 ETSI
ODU 9423 fs=1200MHz 1-1 ETSI
ODU 9423 fs=1200MHz 1-1 ETSI
ODU 9423 fs=1200MHz 2-2 ETSI
ODU 9423 fs=1197MHz 1-1
ODU 9423 fs=1197MHz 1-1
ODU 9423 fs=1197MHz 2-2
ODU 9423 fs=1197MHz 2-2
ODU 9423 fs=1232MHz 1-1
ODU 9423 fs=1232MHz 2-2
ODU 9423 fs=1232MHz 1-1
ODU 9423 fs=1232MHz 2-2
ODU 9423 fs=1200-1232MHz 1
ODU 9423 fs=1050-1200-1232MHz 2
ODU 9423 fs=1200-1232MHz 1P
ODU 9423 fs=1050-1200-1232MHz 2P
Q.ty In = Integrated Antenna
Note:
AODU 32E1
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
(A)
(A)
(A)
(A)
(A)
(A)
(A)
(A)
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2In/N
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
1N
1N
1N
1N
1N
1N
2
2N
2N
2In/N
2In/N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
Q.ty N= Not Integrated Antenna
Table 10 9423 AWY - ODU Installation materials for Integrated or Not Integrated antenna case
ED 05
3DB 06687 DAAA
41/178
9425 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Description
Coupler
3CC13473ABXX
Alcatel
part
number
3CC13734ABAA
3CC13735ABAA
3CC13736ABAA
3CC13737ABAA
Alcatel
part
number
1AF10018AFAA
1AF13284AAAA
1AF13284AAAA
1AF10018AHAA
1AF13291AAAA
1AF11518AAXX
1AF11287AAXX
3CC05749ACAA
1AB146090002
1AB128510002
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
Quantity / Configuration
1+1
HST
1+0
18/23/245 GHz 10db Coupler
Transceiver
ODU 9425 fs=1008MHz 1-1
ODU 9425 fs=1008MHz 2-2
ODU 9425 fs=1008MHz 1-1
ODU 9425 fs=1008MHz 2-2
Installation Materials
25 GHz 1FT SP INTEGR.ANTENNA RFS
25 GHz 1FT SP AWY FULL INTEGRATED ANDREW
25 GHz 1FT AWY FULL INTEGRATED ANDREW
25 GHz 2FT SP INTEGR.ANTENNA RFS
25 GHz 2FT SP AWY FULL INTEGRATED ANDREW
25 GHz 3FT SP INTEGR.ANTENNA
25 GHz 4FT SP INTEGR.ANTENNA
18/23/25 GHz Flex Twist
18/23/25 Nose-Adapter (Non Integr.Antenna)
Non Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N.90 50 ohm
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1
1+0
1+1
HST
1
1
1
1
2
2
2
2
1+0
1+1
HST
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1In/N 1In/N
1In/N 1In/N
2In/N
2In/N
1N
1N
2In/N
2In/N
1In/N
1In/N
1In/N
1In/N
1N
1N
1N
1In
1In
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
1N
1N
1N
1N
2
2N
2N
2In/N
2In/N
2In/N
2In/N
2N
2N
2N
2In
2In
1In/N
1In/N
1In/N
1In/N
1In/N
1In/N
1N
1In
1In
(A)
(A)
(A)
(A)
Cabinet grounding kit
Q.ty In = Integrated Antenna
Note:
AODU 32E1
Q.ty N= Not Integrated Antenna
Table 11 9425 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases
ED 05
3DB 06687 DAAA
42/178
9428 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Description
Coupler
3CC13474ABXX
Alcatel
part
number
3CC13738ABAA
3CC13739ABAA
3CC13740ABAA
3CC13741ABAA
Alcatel
part
number
3DB00658AAXX
3DB00658AAXX
1AF13283AAAA
3DB00659AAXX
3DB00659AAXX
1AF13290AAAA
3DB00682AAXX
3DB02082AAXX
3DB00692AAXX
3DB03455AAXX
1AB128510002
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
Quantity / Configuration
1+0
28/38 GHz 10db Coupler
Transceiver
ODU 9428 fs=1008MHz 1-1
ODU 9428 fs=1008MHz 2-2
ODU 9428 fs=1008MHz 1-1
ODU 9428 fs=1008MHz 2-2
Installation Materials
28 GHz 1FT SP INTEGR.ANTENNA RFS
28 GHz 1FT SP INTEGR.ANTENNA ANDREW
28 GHz 1FT AWY FULL INTEGRATED ANDREW
28 GHz 2FT SP INTEGR.ANTENNA RFS
28 GHz 2FT SP INTEGR.ANTENNA ANDREW
28 GHz 2FT AWY FULL INTEGRATED ANDREW
28/38 GHz Flex Twist
28/38 Nose-Adapter (Non Integr.Antenna)
FLEX-TWIST ARM SUPPORT 28-38GHz
(Non Integr.Antenna)
Universal Round Collar
Non Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N.90 50 ohm
Cabinet grounding kit
Q.ty In = Integrated Antenna
Note:
AODU 32E1
1+1
HST
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1
1+0
1+1
HST
1
1
1
1
2
2
2
2
1+0
1+1
HST
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1In/N 1In/N
1In/N 1In/N
2In/N
2In/N
1N
1N
2In/N
2In/N
1In/N 1In/N
1In/N 1In/N
2In/N
2In/N
1N
1N
2In/N
2In/N
2N
2N
2
2N
2N
2N
1N
1N
1In/N
1In/N
(A)
(A)
(A)
(A)
1
1N
1In
1In
1
1N
1In
1In
2
2N
2In
2In
2
2N
2
2N
2In
2In
Q.ty N= Not Integrated Antenna
Table 12 9428 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases
ED 05
3DB 06687 DAAA
43/178
9438 AWY - ODU INSTALLATION COMPONENTS
Alactel
Part
Number
Description
Coupler
3CC13474AB**
Alcatel
part
number
3CC12987ABAA
3CC12988ABAA
3CC12989ABAA
3CC12990ABAA
3CC13933AAXX
3CC13934AAXX
3CC13052AAXX
3CC13053AAXX
3CC13054AAXX
3CC13055AAXX
Alcatel
part
number
1AF10018AJAA
1AF01739AAAA
3DB00656AAXX
1AF10018AGAA
1AF01740AAAA
1AF13289AAAA
3DB00682AAXX
3DB02082AAXX
3DB00692AAXX
3DB03455AAXX
1AB128510002
3CC10752ABAA
3CC10752ABAB
3CC06503AAXX
1AB128500002
1AC001100022
1AB095530021
3CC08166ABAA
Quantity / Configuration
1+0
28/38 GHz 10db Coupler
Transceiver
ODU 9438 fs=1260MHz 1-1
ODU 9438 fs=1260MHz 2-2
ODU 9438 fs=1260MHz 1-1
ODU 9438 fs=1260MHz 2-2
ODU 9438 fs=700MHz Canada 2-2
ODU 9438 fs=700MHz Canada 2-2
ODU 9438 fs=700MHz 1-1 ANSI
ODU 9438 fs=700MHz 2-2 ANSI
ODU 9438 fs=700MHz 1-1 ANSI
ODU 9438 fs=700MHz 2-2 ANSI
Installation Materials
38 GHz 1FT SP INTEGR.ANTENNA RFS
38 GHz 1FT SP INTEGR.ANTENNA ANDREW
38 GHz 1FT AWY FULL INTEGRATED ANDREW
38 GHz 2FT SP INTEGR.ANTENNA RFS
38 GHz 2FT SP INTEGR.ANTENNA ANDREW
38 GHz 2FT AWY FULL INTEGRATED ANDREW
28/38 GHz Flex.Twist
28/38 Nose-Adapter (Non Integr.Antenna)
FLEX-TWIST ARM SUPPORT 28-38GHz
(Non Integr.Antenna)
Universal Round Collar
Non Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Integrated Antenna Pole Mounting
Consumable set
IDU-ODU cable grounding kit
Filotex Coax cable 50 ohm
Filotex conn. male N.90 ohm 90
Cabinet grounding kit
Q.ty In = Integrated Antenna
Note:
AODU 32E1
1+1
HST
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1
1+0
1+1
HST
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
1+0
1+1
HST
1+1
1+1
1+1
Note
HST SD FD AP FD DA
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1+1
1+1
1+1
Note
HST SD FD AP FD DA
1In/N 1In/N
1In/N 1In/N
2In/N
2In/N
1N
1N
2In/N
2In/N
1In/N 1In/N
1In/N 1In/N
2In/N
2In/N
1N
1N
2In/N
2In/N
2N
2N
2
2N
2N
2N
1N
1N
1In/N
1In/N
(A)
(A)
(A)
(A)
1
1N
1In
1In
1
1N
1In
1In
2
2N
2In
2In
2
2N
2
2N
2In
2In
Q.ty N= Not Integrated Antenna
Table 13 9438 AWY - ODU Installation materials for Integrated or Not Integrated antenna cases
ED 05
3DB 06687 DAAA
44/178
3.7.2.
IDU installation components
Two IDU boxes (Main / Extension) are foreseen:
-
(1+0):
44,45 x 443 x 210mm (=> 1U) + Mini-distributor (=> 0.6U)
(1 Main + Extension):
89,9x443x 210mm (=> 2U) + Mini-distributor (=> 0.6U)
Indoor units (IDU) of the 9400 AWY system can be installed in different ways as described below:
-
Installation on a special workbench or desk;
Installation on a suitable wooden or masonry wall;
- Installation in a 19" Din rack
- Installation in a 21" ETSI rack
For each of the above type of installation special mechanical supporting fixtures are available.
Table 14 -.on page 45 gives a list of the installation materials that are included in the catalogue.
Table 14 - IDU Installation components
IDU INSTALLATION COMPONENTS
ALCATEL
PART NUMBER
3DB04656AAAA
3DB04657AAAA
3CC09614AAAA
3DB06612AAAA
3CC13423AAAA
3CC07946AAAA
1AF12831AAAA
3DB06594AAAA
3DB06593AAAA
3CC13659AAAA
3DB06592ABAA
1AB152220001
1AD053060001
B0177096497
1AB058580014
1AB128500002
1AC001100022
1AB095530021
3DB05594AAAA
3DB05922AAAA
3DB05923AAAA
3DB10064AAAA
3DB10063AAAA
1AB054120027
3DB10003AAAA
1AB061220005
1AB009870002
1AB006420060
1AB009790019
1AB002130006
1AB006020076
1AC011980001
3CC07899AAAC
1AC021980001
3DB05850AAXX
3DB05851AAXX
3CC08951ACAA
3CC07917AAAA
3DB10008AAAA
3DB10007AAXX
3CC08061AAAA
ED 05
NOTE
NAME
ETSI RACK H 2200
ETSI RACK H 2000
IDU Wall Mounting
1+0 ETSI RackMounting Kit
Grounding Kit wall mounting
Telephone Handset
Telephone Handset
User Service Channel cable for 1+1
E3/DS3 cable for 1+1
37 wires 8E1/DS1 cable for 1+1
100 wire SCSI cable for 1+1
6 Breakers DC Power Panel
6 Fuse DC Power Panel
Single fuse holder with fuse
One ciruit breaker
IDU-ODU cable grounding kit
FILOTEX COAX CABLE 50 OHM
FILOTEX CONN.MALE 90 50 OHM
HA-HC/SC cable
NMS/AUDIO CABLE L=1.6 m
NMS/AUDIO CABLE L=6.4 m
NMS Interface AWY-MELODIE IDU L=6.4m
NMS Interface AWY-MELODIE IDU L=1.6m
RS232 CT cable
75 ohm coax cable 8XE1/DS1 IDU/Distr no connectors L:15
Male coax connector 1.0/2.3
Male coax connector 1.6/5.6
Male coax connector BNC 75ohm
Panel coax connector 1.0/2.3
Panel coax connector 1.6/5.6
Panel coax connector BNC 75ohm
120ohm 8X2 twisted pair cable
8E1/DS1 SUB D37 connector
100ohm cable for 8XDS1
ADAPT.CABLE 1.0/2.3 MALE-BNC.FEMALE
ADAPT.CABLE 1.0/2.3 MALE 1.6/5.6 FEMALE
120ohm cable L904/16p lg 15m w connector
COMPAX module 10 pairs and covers
COAX CABLE 8XE1/DS1 IDU/DISTR. 1.0/2.3 75ohm UNB
COAX CABLE 8XE1/DS1 IDU/DISTR. 120 ohm BAL
DISTRIBUTOR SUBRACK FOR 1.6/5.6
3DB 06687 DAAA
45/178
3CC07885ABAA
3CC08062AAAA
3CC07810AAAA
3CC07658AAAB
3CC08061ABAA
3CC07759ABAA
3CC08209AAAA
3CC08212AAAA
3CC08165AAAA
3CC08211AAAA
3CC06503AAXX
3CC13477AAXX
3DB05021AAAA
3DB14051AAAA
3DB14046AAAA
3DB14050AAAA
3DB10087AAAA
3DB10088AAAA
COAX CABLE 8XE1/DS1 IDU/DISTR. 1.6/5.6 75ohm UNB 2m
1U DISTRIBUTOR SUBRACK FOR 120 ohm non EMC
3U DISTRIBUTOR SUBRACK FOR 120 ohm EMC
Cable 8XE1/DS1 IDU/DISTR. 120 ohm 2m
DISTRIBUTOR SUBRACK FO BNC
Cable 8XE1/DS1 IDU/DISTR. BNC 75 ohm UNB 2m
2)
Power supply connection 24V (3X2.5
2)
Connection cable 24V (3X10
2)
Power supply connection 48V (3X1.5
2)
Connection cable 48V (3X4
Consumable set
Light service kit cable
Ethernet crossover cable L=2m
Ethernet crossover cable L=6.4m
Ethernet L=2m
Ethernet L=6,4m
ESC AWY connection L= 1.6m
ESC AWY connection L= 6.4m
Note: Kit Also Used For Bench Installation
The same mechanical support intended for wall installations can be used for bench installation to provide
greater stability on the equipped bench or desk.
The workbench or desk to be used is a table especially fitted with safety power outlets, located in a suitable
spot of the room, and suitably protected against accidental tampering.
ED 05
3DB 06687 DAAA
46/178
4. OUTDOOR UNITS INSTALLATION (ODU)
4.1.
General
9400 AWY ODU units are designed for assembly:
-Either with an integrated antenna connected directly to the Outdoor equipment, see paragraph 4.4 and
4.5.
-With one or more nonintegrated antennas, see paragraph 4.8.
Locking Hook
Light
Service Kit
Grounding
point
I/O Cable IDU-ODU
I/O Cable
IDU-ODU
Light
Service Kit
Figure 15 - 13-38GHz ODU rear and front views
ED 05
3DB 06687 DAAA
47/178
LOCKING HOOK
GROUNDING POINT
PORTABLE
SERVICE
LIGHT
SERVICE
KIT KIT
I/O CABLE IDU/ODU
I/O CABLE IDU/ODU
LIGHT
SERVICE
KITKIT
PORTABLE
SERVICE
Figure 16 7-8 GHz ODU rear and front views
ED 05
3DB 06687 DAAA
48/178
4.2.
TRANSCEIVER (A-box) and BRANCHING (D-box) boxes coupling
A-BOX
Detail A
LOW
FREQ.
HIGH
FREQ.
Detail B
LOW
FREQ.
HIGH
FREQ.
D-BOX
Figure 17 D-BOX and A-BOX Integration
For more information to see the User Manual/Technical Handbook 9400AWY Rel.2.0
ED 05
3DB 06687 DAAA
49/178
4.3.
Typical installation layout
Figure 18 on page 51, Figure 19 page 52, and Figure 20 on page 53 show typical installation layouts. The
installation materials included from Table 6 to Table 13 are also pointed out and shown in the figures
NB: Not in all 1+1 configurationthe external coupler is used. In 1+1HSB-SD the coupler is not used,
in this case it is necessary to use the same Flextwist used in 1+0, that is the 1AF119977AAAA
Figure 18 on page 51 and Figure 19 on page 52 show typical installations of 1+0 and 1+1 systems
respectively, both with 30 cm or 60 cm. integrated antenna
Figure 20 on page 53 shows a typical installation of 1+0 system with not integrated antenna for 13-38 GHz
frequency range. The antenna is installed near the ODU installation making use of the 600 mm. flexible
twist wave-guide, included in Error! Reference source not found. on page Error! Bookmark not
defined. (PN 597210011).
Figure 59 on page 86shows the typical installations of ODU 1+1 on the pole mounting with Not Integrated
antenna for 7-8GHz frequency range. The antenna is installed making use of the 1m flexible twist waveguide (1AF02749ABAAA), included in Table 6 on page 37.
ED 05
3DB 06687 DAAA
50/178
TYPE N CONNECTOR
POLE
GROUNDING
Colson Cable ties
GROUNDING
See NOTE A/3
See NOTE B and C
INDOOR
UNIT
Rear side
GROUNDING
POINT
Rack (Shelf or Desktop)
See NOTE A/4
See NOTE A/3
Figure 18 - Typical installation of 1+0 ODU with integrated antenna, 30 cm or 60 cm.
NOTE A:
1)
2)
3)
4)
The cable is fixed along the supporting pipe or pole by the normal methods (Colson cable ties
are supplied in the optional consumables kit)
see NOTE B.
The rack can be connected to ground using the top or the bottom side grounding points.
For the installation on shelf or desktop the indoor unit must be connected to ground using the
rear side grounding point.
NOTE B : Coaxial cable grounding Kit
First in prossimity of ODU
Second in prossimity of building access
In case of cable length over 80 m, the cable grounding kit must be implemented every 40 meter cable
distance.
NOTE C: see par. 4.14 IDU / ODU cable grounding kit assembling on page 98
ED 05
3DB 06687 DAAA
51/178
13-38GHz
7-8GHz
TYPE N CONNECTOR
7-8GHz
Colson Cable
ties
See NOTE A/3
Grounding
See NOTE B and C
INDOOR
Rear side UNIT
GROUNDING
POINT
Rack (Shelf or Desktop See NOTE A/4
-
See NOTE A/3
Figure 19 - Typical installation of 1+1 ODU with integrated antenna, 30 cm or 60 cm.
NOTE A:
1)
2)
3)
4)
The cable is fixed along the supporting pipe or pole by the normal methods (Colson cable ties
are supplied in the optional consumables kit)
see NOTE B
The rack can be connected to ground using the top or the bottom side grounding points.
For the installation on shelf or desktop the indoor unit must be connected to ground using the
rear side grounding point.
NOTE B: Coaxial cable grounding Kit
First in proximity of ODU
Second in proximity of building access
In case of cable length over 80 m, the cable grounding kit must be implemented every 40 meter cable
distance.
NOTE C: see par. 4.14 IDU / ODU cable grounding kit assembling on page 98
ED 05
3DB 06687 DAAA
52/178
GROUNDING KIT
POLE
ANTENNA
GROUNDING
GROUND
CABLE
WAVEGUIDE
WAVEGUIDE
FLANGE
ANTENNA
FLANGE
Type N Connector
Colson Cable ties
GROUNDING
See NOTE B and C
See NOTE A/3
(
INDOOR
Rear side UNIT
GROUNDING
POINT
Rack (Shelf or Desktop See NOTE A/4)
-
See NOTE A/3
Figure 20 - Typical install. of 1+0 ODU with non integrated antenna and the 600 mm.
flexible twist or optimized Wave-guide length
NOTE A:
1)
2)
3)
4)
The cable is fixed along the supporting pipe or pole by the normal methods (Colson cable ties
are supplied in the optional consumables kit)
see NOTE B
The rack can be connected to ground using the top or the bottom side grounding points.
For the installation on shelf or desktop the indoor unit must be connected to ground using the
rear side grounding point.
NOTE B: Coaxial cable grounding Kit
First in proximity of ODU
Second in proximity of building access
In case of cable length over 80 m, the cable grounding kit must be implemented every 40 meter cable
distance.
NOTE C: see par. 4.14 IDU / ODU cable grounding kit assembling on page 98
ED 05
3DB 06687 DAAA
53/178
Available only for 38 GHz for lower
frequency Flex-twist use plastic
streaps
POLE
FLEX TWIST or
WAVE GUIDE
GROUNDING KIT
13-38GHz
R3
GROUND
CABLE
WAVEGUIDE
WAVEGUIDE
FLANGE
ANTENNA
FLANGE
7-8GHz
GROUNDING
See NOTE B and C
See NOTE A/3
POLE
)
INDOOR
Rear side UNIT
GROUNDING
POINT
RACK (SHELF or DESKTOP - SEE NOTE 4)
See NOTE A/3
Figure 21 - Typical install. of 1+1 ODU with non integrated antenna and the 600 mm. flexible twist or
optimized Wave-guide length
NOTE A:
1)
2)
3)
4)
The cable is fixed along the supporting pipe or pole by the normal methods (Colson cable ties
are supplied in the optional consumables kit)
see NOTE B
The rack can be connected to ground using the top or the bottom side grounding points.
For the installation on shelf or desktop the indoor unit must be connected to ground using the
rear side grounding point.
NOTE B: Coaxial cable grounding Kit
First in prossimity of ODU
Second in proximity of building access
In case of cable length over 80 m, the cable grounding kit must be implemented every 40 meter cable
distance.
NOTE C: see par. 4.14 IDU / ODU cable grounding kit assembling on page 98
ED 05
3DB 06687 DAAA
54/178
4.4.
1+0 ODU configuration Installation with integrated antenna
4.4.1.
-
Required Parts
Integrated antenna
- Antenna Mounting Hardware
- Pole Mounting Assembly
Outdoor Unit and mounting hardware.
4.4.2.
Pole mounting assembly
This assembly is valid only for integrated antenna diameters up to 0.6 m (two feet). The integrated antenna
is mounted on the pole front. The outdoor pole mounting system is designed for quick mechanical
installation.
5
6
2
3
4
1)
2)
3)
4)
5)
6)
ODU radio (and detail of horizontal polarization)
U Bolts For Pole diameter from 90 mm up to 114 mm
Screws to fasten antenna to support
Antenna screw-fastening slots
Integrated Antenna (and detail of horizontal polarization)
Radio mounting
N.B.: To avoid equipment damage the bolt tightening torque for fixing the bolts (3) to antenna slots
(4) must be 80 kg x cm (8 Newton x m) (5.76 lb.ft). For U-bolts (2) the bolt tightening torque
must be 342,3 kg x cm (33,55 Newton x m) (24.65 lb.ft). Exceeding this value may result in bolt
breaking.
Figure 22 - Integrated pole mounting with ODU 1+0, Horizontal Polarization
ED 05
3DB 06687 DAAA
55/178
Figure 23 - Integrated antenna pole mounting with ODU 1+0, Vertical Polarization
ED 05
3DB 06687 DAAA
56/178
Figure 24 7-8 GHz Integrated antenna pole mounting with ODU 1+0, Vertical Polarization
The mechanical system can be secured to any fixing pole with a diameter of between 90 and 114 mm.
A pole diameter of 114 mm is, however, recommended. With smaller diameters, mounting is possible, if
special attention is paid to the mechanical rigidity of the assembly.
There are also supports for fixing the pole to the wall: please consult us.
Various antenna types and sizes can be used, together with radio systems operating at different
frequencies and in a variety of configurations.
ED 05
3DB 06687 DAAA
57/178
4.4.3.
-
General Procedural Sequence:
Install the pole mounting assembly on mast;
Turn the Antenna Nose according to the Hop polarization
Install the antenna on pole mounting,
Install the ODU;
Pre-point the antenna;
see paragraph 4.4.5.
see paragraph 4.4.6.
see paragraph 4.4.6.
see paragraph 4.4.7
see paragraph 4.4.8
Alternative possibility:
Install Antenna on pole mounting
Turn Antenna nose
Install pole mounting with Antenna
Prepoint Antenna
Install ODU
4.4.4.
Procedure note
NOTE: When attaching the antenna, ODU mounting hooks, and ODU, adhere to the following:
-
position the antenna with the drain hole to the bottom,
remove the antenna node protecting plug and position the antenna node wide dimension horizontal for
vertical polarization or vertical for horizontal polarization,
position the ODU fastening hooks and the ODU horizontal for vertical polarization or vertical for
horizontal polarization.
4.4.5.
-
Installing the pole mounting on mast
Position the U bolts (2) on the pole fit the flat washers, growe washers, nuts and lock nuts (1).
Point the pole mounting in the required direction using a compass and a pair of binoculars, and then
secure the brackets.
N.B.:
For U-bolts the bolt tightening torque must be 342.3 kg x cm (33.55 Newton x m)(24.65
lb.ft).Exceeding this value may result in bolt breaking
Figure 25 - Pole mounting installation for integrated antenna
ED 05
3DB 06687 DAAA
58/178
4.4.6.
Installing the antenna on the pole mounting
Turn the Antenna Nose according to the Hop polarization
Before to position the antenna vertically (node assembling ), with the drain hole in the bottom part and
free of obstacles.
Insert the M6 screws (7 in all) (1) with their onduflex springy crinkle washers, tighten and secure the
screws.
Socket cap torque
Socket cap torque
Socket cap torque
Silicon grease
NB. : To turn the Antenna polarization, loose the 3 Socket cap screw and turn 90 the Nose, tight the screw
NB. : Before inserting the ODU onto the Nose, apply the sullied gel on the O-ring
Figure 26 - Change polarisation description
The antennas are normally supplied with vertical polarization. To change the polarization: undo the three
socket cap torque and turn the nose through 90 degrees then tighten the screws again. (See Figure 27 on
page 59).
Figure 27 - Installation with integrated antenna and Vertical polarization
ED 05
3DB 06687 DAAA
59/178
4.4.7.
Installing the ODU
- Remove the solar shield by unscrewing the two solar shield screws
- Grasp the ODU module by the handle.
- Open the four looking hooks (1) arranged on the four walls of the ODU unit
- Rotate the ODU depending to horizontal or vertical polarization,
- Plug-in insert the specific brackets (2) to the support (Radio mounting),
WARNING:
is mandatory to fix the four looking hooks like indicated and that is on the
binary inside
- Secure the ODU module through the four hooks (1) on the relative brackets (2).
- Reinstall the solar shield onto the RT by screwing on it the two solar shield screws
GROUNDING
POINT UP
GROUNDING
POINT DOWN
GROUNDING
POINT
Figure 28 - ODU 1+0 installation for integrated antenna
REMINDER:
The ODU/antenna assembly requires no additional seal on the SHF flanges; the two ends
are smooth. The O-ring seal around the male noses provides sealing.
NB: Before to connect the ODU it is mandatory to put SILICONE grease on the O-ring.
ED 05
3DB 06687 DAAA
60/178
4.4.8.
Pointing the antenna
4.4.8.1. Pole mounting types
3CC10752ABAA
3CC10752ABAB
Figure 29 Pole mounting types
4.4.8.2. Antenna mechanical pre-pointing
Overall antenna steer (with turnbuckles set to the maximum) is:
Bearing: 360 degrees for 30 cm and 60 cm diameter antenna,
The steer obtained by the turnbuckles is:
Elevation: + 25 degrees,
Bearing: + 10 degrees.
Figure 30 Stretching screw (3CC14292AAAA)
ED 05
3DB 06687 DAAA
61/178
Figure 31 Pole mounting without Stretching screw inserted
F1
F2
F3
A
B
Figure 32 Stretching screw inserted (Vertical alignment)
F1-F2-F3
A
B
ED 05
Vertical position coarse alignment movement tighten screw
Vertical position rotational axis
Vertical fine alignment nut mouvement (Stretching screw)
3DB 06687 DAAA
62/178
D
C1
D1
Figure 33 Integrated pole mounting (Horizontal alignment)
C
Horizontal position rotational axis
C1 Horizontal position rotational axis (under)
D
Horizontal position coarse alignment movement tighten screw
D1 Horizontal position coarse alignment movement tighten screw (under)
E
Bolts
First horizontal pre-pointing (azimuth)
Horizontally place the antenna according to the direction set down in the plant documents where, among
the various indication are indicated those concerning the reference points (Position of the tower or of the
building with respect to true north) in order to point the antenna in the set direction.
There are various procedures and technical means to adopt in order to mechanically pre-point the antenna,
and they can be implemented in various ways according to the various configurations and to the various
system conditions.
The standard instrumentation is the - compass.
Second vertical pre-pointing (zenith)
Place the antenna vertically nearest to its operating angle.
The technical and operative procedure adopted to vertically point the antenna is as that previously
implemented to horizontally pre-point.
Note
a)
b)
c)
At the end of the pre-pointing operation, slowly block all the horizontal and vertical regulating system
of the antenna taking care not to modify dish direction
Final antenna pointing (or connection) shall be established only after all the Antenna and ODU
system is fully installed.
After the fine pointing TIGHTENING TORQUE FOR THE SCREWS OF M10 IS OF 30Nm
(ScrewsA - C- C1- D- D - F1 - F2- F3)
NOTE:
ED 05
for more information see the 9400AWY REL.2.0 User Manual/Line Up Guide
3DB 06687 DAAA
63/178
4.4.9.
Installation on the wall information
Note: In certain pole mounting installation circumstances, due to various reasons such as protrusions from
the wall, it might be useful to mount as shown on page 64 in order to easily install ODU module.
POLE
WALL
Figure 34 - Pole mounting near a wall
ED 05
3DB 06687 DAAA
64/178
4.4.10.
Antenna 3 / 4 Feet Installation Instructions
The instructions for the assemblage of the antenna are normally contained in the box of the same antenna.
Following are shown only some examples of assemblage of antennas
V
H
Figure 35 3 Feet Antenna (Configuration 1+0)
ED 05
3DB 06687 DAAA
65/178
V
H
Figure 36- 4 Feet Antenna (Configuration 1+0)
ED 05
3DB 06687 DAAA
66/178
4.5.
13-38GHz - 1+1 ODU configuration Installation with integrated antenna
4.5.1.
-
Required Parts Listing
Integrated antenna
Antenna Mounting Hardware .
Pole Mounting Assembly
Outdoor Unit and mounting hardware.
2
3
4
5
Silicon grease
7
8
Silicon grease
Figure 37 - Typical installation pole mounting with ODU 1+1 for integrated antenna
1)
2)
3)
4)
5)
6)
7)
8)
U bolts
Pole mounting
Radio mounting
Fastening points for COUPLER
Screws fastening the antenna to the support
Antenna screw-fastening slots
RF Coupler Fastening brackets for ODU
Grounding points
N.B.:
ED 05
To avoid equipment damage the bolt tightening torque for fixing the bolts (5) to antenna
slots (6) must be 80 kg x cm (8 Newton x m) (5.76 lb.ft). For U-bolts (1) the bolt tightening
torque must be 342.3 kg x cm (33.55 Newton x m) (24.65 lb.ft). Exceeding this value may
result in bolt breaking.
3DB 06687 DAAA
67/178
4.5.2.
-
13-38GHz - 1+1 Typical installation (General Procedural Sequence)
Install the pole mounting assembly on mast; see paragraph 4.4.5;
Install the antenna on the pole mounting, see paragraph 4.4.6;
Install the Coupler, see paragraph 4.5.2.1;
Install the ODU, see paragraph 4.5.2.2;
Point the antenna, see paragraph 4.4.8.
4.5.2.1. Installing the coupler
Grasp the coupler by the handle. Fasten the coupler to the support through the four locking hooks (1)
that will be tightened onto the relative fastening brackets on the radio support (2).
The reference in Figure 38 is important for the correct installation of the coupler
Ththe label corresponds to the side of the pole
PIPE
Side
Pole
MAIN
ACCESS
Figure 38 - Installing the Coupler To the Radio Support
ED 05
3DB 06687 DAAA
68/178
4.5.2.2. 13-38GHz - Installing the ODU 1+1
Grasp two modules ODU by the handle. Fasten the ODU module to the support through the locking hooks
(1-2-3-4) that will be tightened onto the relative fastening bracket on the coupler.
Procedure to install the ODU modules
ODU A : hooks (1), hooks (2), hooks (3), hooks (4)
ODU B : hooks (1), hooks (2), hooks (3), hooks (4)
ODU A
Locking hooks
3
1
2
4
3
1
Fastening
brackets
2
ODU B
Figure 39 - Installing the RF coupler with ODU 1+1 for integrated antenna
ED 05
3DB 06687 DAAA
69/178
4.5.3.
13-38GHz Change polarization in 1+1 configuration
The axial adaptation between H polarization to V polarization (and viceversa) is a mechanical/electrical
adjustment. Every mechanical STEP is 30 adjustment.
2nd Step
1st Step
Figure 40 1st Step and 2nd step
4.5.3.1. Change Polarization Procedure
1st Step = internal 30 rotate
Coupler body
1st Step
Rotate 30
Figure 41 1st Step inserted
ED 05
3DB 06687 DAAA
70/178
2nd Step= cover + screws 60( 30+ 30) rotate
Coupler body
2st Step
Rotate 60
Figure 42 2nd Step inserted
The spigot in the Integrated Antenna configuration is 30 and complete the change of polarization (90).
Figure 43 Screws fixing
ED 05
3DB 06687 DAAA
71/178
4.6.
7- 8GHz 1+1 ODU configuration Installation with integrated antenna
(Alternative A)
4.6.1.
-
Required Parts Listing
Integrated antenna
Antenna Mounting Hardware .
Pole Mounting Assembly
Coupler
Outdoor Unit and mounting hardware.
MAIN
ACCESS
Silicon greeze has to be added
on the O-ring
Figure 44 - Typical installation pole mounting with ODU 1+1 for integrated antenna (7-8GHz)
ED 05
3DB 06687 DAAA
72/178
4.6.2.
-
7- 8GHz 1+1 Typical installation (General Procedural Sequence)
Install the pole mounting assembly on mast; see paragraph 4.4.5;
Install the antenna on the pole mounting, see paragraph 4.4.6;
Install the Coupler, see paragraph 4.6.2.1;
Install the ODU, see paragraph 4.6.2.2;
Point the antenna, see paragraph 4.4.8.
4.6.2.1. Installing the coupler
Grasp the coupler by the handle. Fasten the coupler to the support through the four locking hooks (1)
that will be tightened onto the relative fastening brackets on the radio support (2).
The reference in Figure 54 is important for the correct installation of the coupler
Ththe label corresponds to the side of the pole
Silicon
greeze
MAIN
ACCESS
Figure 45 - Installing the Coupler To the Radio Support
ED 05
3DB 06687 DAAA
73/178
4.6.2.2. Installing the ODU 1+1
Grasp two modules ODU by the handle. Fasten the ODU module to the support through the locking hooks
(1-2-3-4) that will be tightened onto the relative fastening bracket on the coupler.
Procedure to install the ODU modules
NB: Before to connect the ODU warn about the fact the Silicone greeze has to be added on the Oring.
ODU A :(SPARE) hooks (A1), hooks (A2), hooks (A3), hooks (A4)
ODU B (MAIN) : hooks (B1), hooks (B2), hooks (B3), hooks (B4)
A1
Silicon greeze
A
Silicon
greeze
A3
A4
A2
B1
B
B3
M
A
I
N
B4
B2
Figure 46 - Installing the RF coupler with ODU 1+1 for integrated antenna
ED 05
3DB 06687 DAAA
74/178
4.6.3.
7- 8GHz Change polarization in 1+1 configuration
Change Polarization procedure
Vertical Polarization to Horizontal Polarization
The point of reference is on the position V (vertical Polarization)
To change the polarization needs to perform the following operations:
To unscrew the three screws
To turn the thin twist and to make to coincide the position H to the point of reference "."
To screw the screws
Horizontal Polarization to Vertical Polarization
The point of reference is on the position H (horizontal Polarization) To change the polarization needs to
perform the following operations:
To unscrew the three screws
To turn the thin twist and to make to coincide the position H to the point of reference "A"
To screw the screws
Point of
reference
A
Detail B
Screw
Point of
reference
A
Detail A
Screw
TWIST
See Detail B
See Detail A
Figure 47 7 8GHz Change Polarization
ED 05
3DB 06687 DAAA
75/178
4.7.
7- 8GHz 1+1 ODU configuration Installation with integrated antenna
(Alternative B)
4.7.1.
-
Required Parts Listing
Integrated antenna
Antenna Mounting Hardware .
Pole Mounting Assembly
Coupler
Outdoor Unit and mounting hardware.
MAIN
MAIN
Figure 48 - Typical installation pole mounting with ODU 1+1 for integrated antenna (7-8GHz)
ED 05
3DB 06687 DAAA
76/178
4.7.2.
-
7- 8GHz 1+1 Typical installation (General Procedure Sequence)
Install the pole mounting assembly on mast; see paragraph 4.4.5;
Install the antenna on the pole mounting, see paragraph 4.4.6;
Install the Coupler, see paragraph 4.7.2.1;
Install the ODU, see paragraph 4.7.2.2;
Point the antenna, see paragraph 4.4.8.
4.7.2.1. Installing the coupler
MAIN
MAIN
MAIN
Figure 49 7- 8GHz Coupler (Alternative B)
Grasp the coupler by the handle. Fasten the coupler to the support through the four locking hooks (1)
that will be tightened onto the relative fastening brackets on the radio support (2).
The reference in Figure 50 is important for the correct installation of the coupler
The label corresponds to the side of the pole
MAIN
1
2
Figure 50 - Installing the Coupler To the Radio Support
ED 05
3DB 06687 DAAA
77/178
4.7.2.2. Installing the ODU 1+1
Grasp two modules ODU by the handle. Fasten the ODU module to the support through the locking hooks
(1-2-3-4) that will be tightened onto the relative fastening bracket on the coupler.
Procedure to install the ODU modules
NB: Before to connect the ODU it is mandatory to put SILICONE grease on the ing.
ODU A (MAIN)
ODU B :(SPARE) ( hooks (B1), hooks (B2), hooks (B3), hooks (4)
ODU B -
ODU B Hook 1
ODU B Hook 1 fixing
ODU B Hook 1 fixed
ODU B Hook 2 Fixing
ODU B Hook 2 Fixed
ODU B - Fixed
ODU A and ODU B Fixed on the Coupler with Solar
shield
Figure 51 - Installing the RF coupler with ODU 1+1 for integrated antenna
ED 05
3DB 06687 DAAA
78/178
7- 8GHz Change polarization in 1+1 configuration
Change Polarization procedure
Vertical Polarization to Horizontal Polarization
The point of reference is on the position V (vertical Polarization)
To change the polarization needs to perform the following operations:
to unscrew the two screws
to turn the thin twist and to make to coincide the position H
to screw the screws
Horizontal Polarization to Vertical Polarization
The point of reference is on the position H (horizontal Polarization) To change the polarization needs to
perform the following operations:
to unscrew the two screws
to turn the thin twist and to make to coincide the position V
to screw the screws
Screw
Screw
Polarization H
Polarization V
Figure 52 7 8GHz Change Polarization
ED 05
3DB 06687 DAAA
79/178
4.8.
1+0 ODU configuration Installation with non-integrated antenna
4.8.1.
-
Required Parts Listing
Non Integrated antenna
Antenna Mounting Hardware and instructions (supplied by manufacturer).
Pole Mounting Assembly
Outdoor Unit and mounting hardware.
Flexible waveguide, gaskets, and fasteners or standard waveguide and flanges.
Figure 53 - Pole mounting installation for not integrated antenna with ODU 1+0
NB: Pole mounting can be installed on the Right or Left hand side of the pole.
4.8.2.
-
General Procedural Sequence
Install the antenna on the mast, according to the instructions given by the manufacturer and supplied
with the antenna, and prepoint the antenna towards the remote station;
install the pole mounting on the mast, see paragraph 4.8.3;
install the ODU, see paragraph 4.8.3.2;
install the flextwist (suited to the frequency) between the Pole M. Nose adaptor and the antenna Nose
Adaptor, see paragraph 4.8.5.
ED 05
3DB 06687 DAAA
80/178
4.8.3.
Install the pole mounting on the mast.
4.8.3.1. Pole mounting assembly
This assembly is valid only for non-integrated antenna.
The outdoor pole mounting system is designed for quick mechanical installation.
The mechanical system can be secured to any fixing pole with a diameter of between 90 and 114 mm.
A pole diameter of 114 mm is, however, recommended. With smaller diameters, mounting is possible, if
special attention is paid to the mechanical rigidity of the assembly.
There are also supports for fixing the pole to the wall: please consult us.
Various antenna types and sizes can be used, together with radio systems operating at different
frequencies and in a variety of configurations.
4.8.3.2. Installing the pole mounting
Figure 54 - Installation of the pole mounting for not integrated antenna
NB: Pole mounting can be installed on the Right or Left hand side of the pole.
-
Position the Pole mounting support on the pole side as shown in the plant documentation.
Position the U bolts (1) on the pole, fit the flat washers, growe washers, nuts and lock nuts (2).
Point the pole mounting in the required direction using a compass and a pair of binoculars, and then
secure the brackets.
To change the polarization: undo the three socket cap screws and turn the nose through 90 degrees
then tighten the screws again. See Figure 27 on page 59.
N.B.: For U-bolts (1) the bolt tightening torque must be 342.3 kg x cm (33.55 Newton x m)(24.65
lb.ft). Exceeding this value may result in bolt breaking.
ED 05
3DB 06687 DAAA
81/178
4.8.4.
Installing the ODU
NB: Pole mounting can be installed on the Right or Left hand side of the pole.
-
Take off the solar shield by unscrewing the two screws placed on the solar shield back panel.
Grasp the ODU module by the handle. Open the four looking hooks (1) arranged on the four walls of
the ODU unit
Position the Pole mounting support on the pole side as shown in the plant documentation.
Position the ODU for desired polarization (horizontal or vertical),
Connect the specific brackets (2) to the support (Radio mounting),
Secure the ODU module through the four hooks (1) onto the relative brackets (2).
Put back the solar shield by screwing the two screws placed on the solar shield back panel.
Figure 55 - ODU 1+0 installation for not integrated antenna
REMINDER:
ED 05
The ODU/antenna assembly requires no additional seal on the SHF flanges; the two
ends are smooth. The O-ring seal around the male noses provides sealing.
3DB 06687 DAAA
82/178
4.8.5.
Installing the Flextwist waveguide
The long twistable flexible waveguide is supplied complete with gaskets and fasteners. At one end, it has a
smooth square flange (to be mounted on the antenna) and at the other end, a grooved square flange
designed to accommodate an O-ring seal (mounted at the ODU end).
Table 15 - 7-8Ghz FLEXTWIST WAVEGUIDE
FLEXIBLE TWISTABLE WAVEGUIDE KIT
Alcatel code
Waveguide
Lenght.
mm.
Freq.Band
Ghz.
1AF11977AAXX
WR112
1.000
7,05 - 10
PDR84
UDR84
3CC08010ABAB
(Note A)
WR112
1.000
7,05 - 10
PBR84
UBR84
Flanges
Stainless
steel
socket
cap
screws
12
(M4x25)
8
(M4x25)
Stainless
steel
socket
cap
screws
8
(M4x20)
8
(M4x12)
Ondulflex
springy
crinkle
washers
Stainless
Z. flat
washers
HM.
Hex
nuts
12 (B4)
12 (Z4)
8 (B4)
8 (Z4)
12
(HM4)
8
(HM4)
Ondulflex
springy
crinkle
washers
Stainless
Z. flat
washers
HM.
Hex
nuts
8 (B4)
12 (Z4)
8 (B4)
8 (Z4)
8 (B3)
8 (Z3)
8 (B3)
8 (Z3)
12
(HM4)
8
(HM4)
8
(HM3)
8
(HM3)
Note A: next introduction in substituition of 1AF11977AAXX
Table 16 - 13-38Ghz FLEXTWIST WAVEGUIDE
FLEXIBLE TWSITABLE WAVEGUIDE KIT
Alcatel code
Waveguide
Lenght.
mm.
Freq.Band
Ghz.
Flanges
3CC05751ACAA
WR75
600
10 15,0
PBR120
UBR120
3CC05750ACAA
WR62
600
12,4 - 18
PBR140
UBR140
3CC05749ACAA
WR42
600
18 26,5
PBR220
UBR220
3DB00682AAAA
WR28
600
26,5 40
PBR320
UBR320
Stainless
steel
socket
cap
screws
8
(M4x20)
8
(M4x20)
8
(M3x20)
8
(M3x20)
Stainless
steel
socket
cap
screws
8
(M4x12)
8
(M4x12)
8
(M3x12)
8
(M3x12)
Note:
If the FLEX-TWIST is not provided by Alcatel, the user must carefully choose the type of the
connection guide in order to limit as much as possible galvanic couples between ANTENNA/flex-twist and
flex-twist/ODU contact surfaces that can induce rust. For this purpose pleae note that the surfaces are:
-
chromium-plated at ODUs output flange side
tin-plated at flex-twists flange side
ED 05
3DB 06687 DAAA
83/178
4.9.
13-38GHz - 1+1 ODU configuration Installation with non-integrated
antenna
Figure 56 on page 84 shows the pole mounting assembling with ODU 1+1 unit.
4.9.1.
-
Non-integrated antenna
Antenna mounting hardware and instructions (supplied by manufacturer)
Pole Mounting Assembly
RF Coupler
Outdoor unit and mounting hardware
Flexible waveguide, gaskets, and fasteners
4.9.2.
-
Required Parts Listing
General Procedural Sequence
Install the antenna on the mast, according to the instructions given by the manufacturer and supplied
with the antenna, and prepoint towards the remote station using a compass and pair of binoculars;
Install the pole mounting on the mast; see paragraph 4.8.3;
Install the RF Coupler
Install the ODU; see paragraph 4.9.3.1;
Install the flextwist (suited to the frequency) between the pole mounting nose adaptor and the to
antenna flange.
1
B
Figure 56 - Pole mounting with ODU 1+1 for not integrated antenna (13 to 38 GHz)
NB: It is highly recommended tu put SILICONE grease on the O-ring of the antenna nose before the
assembly with the coupler (see point A). The same rule is applicable for the O-ring of the
coupler (see point B).
N.B.: For U-bolts (1) the bolt tightening torque must be 342.3 kg x cm (33.55 Newton x m)(24.65
lb.ft). Exceeding this value may result in bolt breaking.
ED 05
3DB 06687 DAAA
84/178
4.9.3.
-
Installing the Coupler
Grasp the coupler by the handle. Fasten the coupler to the support through the four locking hooks (1)
that will be tightened onto the relative fastening brackets on the radio support (2).
Silicone
grease
Figure 57 - Installation of the Coupler on the pole mounting (13 to 38 GHz)
4.9.3.1. Install the ODU
-
Grasp two modules ODU by the handle. Fasten the ODU module to the support through the locking
hooks (3) that will be tightened onto the relative fastening bracket on the coupler (4).
Reinstall the solar shield onto the ODU.
ODU
3
ODU
Figure 58 - Installation of ODU 1+1 on the pole mounting for not integrated antenna (11 to 38 GHz)
ED 05
3DB 06687 DAAA
85/178
4.10.
7- 8GHz - 1+1 ODU configuration Installation with non-integrated antenna
(Alternative A)
Nose Adapter
Figure 59 - Pole mounting ODU 1+1 for not integrated antenna
with Nose Adapter (7 - 8GHz) 3DB01459AAAA
Figure 60 - Pole mounting ODU 1+1 for not integrated antenna
Nose Adapter (7 - 8GHz) 3DB10136AAAA
ED 05
3DB 06687 DAAA
86/178
4.10.1.
-
Non-integrated antenna
Antenna mounting hardware and instructions (supplied by manufacturer)
Pole Mounting Assembly
RF Coupler
Nose Adapter
Outdoor unit and mounting hardware
Flexible waveguide, gaskets, and fasteners
4.10.2.
-
Required Parts Listing
General Procedural Sequence
Install the antenna on the mast, according to the instructions given by the manufacturer and supplied
with the antenna, and prepoint towards the remote station using a compass and pair of binoculars;
Install the pole mounting on the mast; see paragraph 4.8.3;
Install the RF Coupler 4.10.3
Install the ODU; see paragraph 4.10.3.1;
Install the flextwist (suited to the frequency) between the pole mounting nose adaptor and the to
antenna flange.
4.10.3.
Installing the Coupler
Grasp the coupler by the handle. Fasten the coupler to the support through the four locking hooks (1)
that will be tightened onto the relative fastening brackets on the radio support (2).
ED 05
3DB 06687 DAAA
87/178
MAIN
ACCESS
MAIN
Figure 61 - Pole mounting/RF COUPLER 1+1 for not integrated antenna (7 - 8GHz)
ED 05
3DB 06687 DAAA
88/178
4.10.3.1. Install the ODU
-
Grasp two modules ODU by the handle. Fasten the ODU module to the support through the locking
hooks (3) that will be tightened onto the relative fastening bracket on the coupler (4). Reinstall the
solar shield onto the ODU.
MAIN
Solar
shields
Figure 62 - Installation of ODU 1+1 on the pole mounting for not integrated antenna (7- 8 GHz)
ED 05
3DB 06687 DAAA
89/178
4.11.
7-8GHz Installation Full Indoor AWY (Two Terminal)
For 7.8GHz an indoor installation of transceiver is available and hereafter described:
2
4
7
8
Figure 63 Panel support 4U 19 for ODU 1+1 and Coupler
(Horizontal position)
ED 05
3DB 06687 DAAA
90/178
1
9
2
To
IDU
5
Figure 64 Panel support 4U 19 for ODU 1+1 and Coupler
(Vertical position)
ED 05
3DB 06687 DAAA
91/178
To antenna
Station A
IDU 1+1
Station A
To antenna
Station C
IDU 1+1
Station C
ODU 1+1
ODU 1+1
11
DehydratoR
Figure 65 Principle Installation in Laborack with ODU 1+1 and Coupler
ED 05
3DB 06687 DAAA
92/178
Figure 66 Support pole mounting (Laborack)
Ref.
1
2
Description
RF Coupler 7/8 GHz
Adapter nose
Code
3CC14536AAAA
3DB10135AAXX
3
4
Casted piece ODU socket restart
Flextwist PDR84/UBR 84L: 1000 mmm
3DB10137AAAA
3CC08010ABXX
FSJ1-50A coax.feed.NM right angl/NMLg3m
3CC09514AAAA
Cabinet grounding kit Y/G for IDU
3CC13423AAAA
7
8
9
Laborack
Fixation support ODU 1+1 in rack
Grounding kit for support ODU
1AD114560001
3CC50023AAAA
3CC08166ABAA
10
11
Consummable kit
Dehydrator
3CC06503AAXX
1AF01052AAAA
Table 17 - AWY 7/8 GHz Installation code Full Indoor housing kit
ED 05
3DB 06687 DAAA
93/178
4.12.
7- 8GHz - 1+1 ODU configuration Installation with non-integrated antenna
(Alternative B)
MAIN
MAIN
Figure 67 - Pole mounting ODU 1+1 for not integrated antenna (7 - 8GHz)
4.12.1.
-
Non-integrated antenna
Antenna mounting hardware and instructions (supplied by manufacturer)
Pole Mounting Assembly
RF Coupler
Nose Adapter (see Figure 60)
Outdoor unit and mounting hardware
Flexible waveguide, gaskets, and fasteners
4.12.2.
-
Required Parts Listing
General Procedural Sequence
Install the antenna on the mast, according to the instructions given by the manufacturer and supplied
with the antenna, and prepoint towards the remote station using a compass and pair of binoculars;
Install the pole mounting on the mast; see paragraph 4.8.3;
Install the RF Coupler 4.12.3
Install the ODU; see paragraph 4.12.3.1;
Install the flextwist (suited to the frequency) between the pole mounting nose adaptor and the to
antenna flange.
ED 05
3DB 06687 DAAA
94/178
4.12.3.
Installing the Coupler
Grasp the coupler by the handle. Fasten the coupler to the support through the four locking hooks (1)
that will be tightened onto the relative fastening brackets on the radio support (2).
Figure 68 - Pole mounting/RF COUPLER 1+1 for not integrated antenna (7 - 8GHz)
ED 05
3DB 06687 DAAA
95/178
4.12.3.1. Install the ODU
-
Grasp two modules ODU by the handle. Fasten the ODU module to the support through the locking
hooks (1) that will be tightened onto the relative fastening bracket on the coupler (2). Reinstall the
solar shield onto the ODU.
MAIN
MAIN
Coupler
O
D
U
Figure 69 - Installation of ODU 1+1 on the pole mounting for not integrated antenna (7- 8 GHz)
ED 05
3DB 06687 DAAA
96/178
4.13.
Solar shield Installation
Figure 70 on page 97 shows the solar shield mounting example (using screws) for ODU 1+0. The same
procedure applies to the 1+1 configuration.
NB. Solar shield has to be installed only after ODU installation.
Solar shield Polarization V
Solar shield Polarization H
The ARROW determines the polarization
In vertical or horizontal polarization, the solar
shield remains fixed in the same position and
the ODU is the only part which can rotate 90
degrees when changing the polarization.
Solar shield screws
Figure 70 - Solar shield installation ODU 1+0
ED 05
3DB 06687 DAAA
97/178
4.14.
IDU / ODU cable grounding kit assembling
Cable grounding kit assembling description:
Cable reference type:
Ref: FILOTEX COAX CABLE 50ohm (1AC001100022)
Cable reference table:
ED 05
3DB 06687 DAAA
98/178
ED 05
3DB 06687 DAAA
99/178
5. INDOOR UNITS INSTALLATION (IDU)
5.1.
General
Indoor units (IDU) of the 9400 AWY system can be installed in different ways as described below:
Installation in a ETSI (WTD) rack (21") and North American standard rack (21") (see paragraph 5.2.1
on page 100) or Laborack (see paragraph 5.2.2 on page 104);
Installation in a 19" DIN rack (see paragraph 5.2.3 on page 105);
Installation on masonry wall (see paragraph 5.4 on page 109).
For each of the above type of installation special mechanical supporting fixtures are available.
Table 14 -.on page 45 gives a list of the installation materials that are included in the catalogue.
5.2.
Rack mount kit description
Special mechanical fittings are provided for this type of installation, depending to the width of rack (19" or
21"). In the paragraph 5.2.1 on page 100 the figures examples shown the fittings used to insert the
equipment in ETSI racks (21"). These examples are also present in paragraph 5.2.3 on page 104 for
installation in 19" DIN racks by changing the adaptors.
5.2.1.
Rack mount installation in ETSI (WTD) and North American standard rack.
For the 1+0 and 1+1 configuration the mechanical fittings are shown in the assembly drawing of Figure 71
on page 101..
The Figure 72 on page 102 shows the types of subrack installation into the rack. The Figure 73 on page
103 shows the typical WTD rack installation with 1+0 and 1+1 equipment.
The
Figure 74 on page 103 shows the coaxial minidistributor wiring.
ED 05
3DB 06687 DAAA
100/178
T.R.U
TOP RACK UNIT
Example of 1+0 IDu with 21" supports for rack mounting
Example of 1+1 IDu with 21" supports for rack mounting
Figure 71 - Example of 1+0 and 1+1 IDU with 21" supports for rack mounting
ED 05
3DB 06687 DAAA
101/178
Detail A - Screw hole
Detail B - Nut cage
Detail A
Detail B
Figure 72 - Subrack installation in 21" rack
ED 05
3DB 06687 DAAA
102/178
Figure 73 View of installation
Figure 74 - Wired mini distributor
ED 05
3DB 06687 DAAA
103/178
5.2.2.
Laborack
The laborack dimensons are:
Height
Width
Depth
2065 mm
545mm
400mm
Ref: 1AD114560001
Figure 75 - Laborack
IDU Installation in Laborack
When you have correctly positioned the fixing brackets on the 19 unit, the front panel will hold the
equipment by four screws fitted into the laborack cage nuts.
Fasten the IDU to the rack by inserting screws into holes of 19 mechanical adaptors and by screwing them
into relevant holes provided with nut cage situated on rack brackets (see Figure 71 on page 101)
ED 05
3DB 06687 DAAA
104/178
5.2.3.
Rack mount adapters installation in a rack
The mechanical fittings are shown in the assembly drawing of Figure 76
19 brackets
21 brackets
Figure 76 - IDU adapter for installation
ED 05
3DB 06687 DAAA
105/178
5.2.4.
Grounding of the subrack
The subrack must be grounded using the Faston connector present on the rear side of the apparatus, see
Figure 77 on page 106 (DETAIL A).
The section cable (wire) to use must be a 1X 3 mm2 (12AWG) (Yellow/Green)
The subrack-mounting item , adds a good electrical connection to rack ground.
DETAIL A
SEE DETAIL A
Figure 77 - Subrack cabinets grounding points
ED 05
3DB 06687 DAAA
106/178
5.3.
Minimum distances between systems installed in the rack
Minim un space between 2 IDU
Space between 1+1 configuration
1+1 IDU Rack
ED 05
3DB 06687 DAAA
107/178
Minimun distance between
1+1 configuration
2U A
1U B
2UA
1U B
2U A
B
A
B
A
1+1 IDU Rack
Figure 78 - Minimum distances for dense packing in both systems (1+0 and 1+1)
Figure 79 Summary of minimum distance in 1+0 and 1+1 configuration
ED 05
3DB 06687 DAAA
108/178
5.4.
Wall mounting kit description
The mechanical support (kit ref. 3CC09614AAAA) can be used for wall installation and it can support a
maximum of three units.
The kit includes:
Two brackets
Four fixing for the brackets
o M6x50 socket cap screws
o Onduflex washers
o Expension bolt
The mechanical support can contain a maximum of ONE unit in case of system 1+0 and TWO units in
case of system 1+1, both equipped with mini distributor.
The possible installations are the followings:
1+0 and 1+1 Installation wall with and without mini distributor
1+0 and 1+1 typical wall installation (horizontal and vertical positioning)
The wooden or masonry wall that is selected for the installation should be in a suitable portion of the room.
Preferably it should be near to a safety power outlet, and it should ensure safeguard against accidental
tampering. It is possible to install the apparatus in a horizontal or vertical position
Detail A
Detail A
Grounding point
The mechanical support must be grounded using the Grounding Kit 3CC13423AAAA
Figure 80 - Fixing the mechanical support to the wall
ED 05
3DB 06687 DAAA
109/178
6. IDU INTERCONNECTIONS
6.1.
Module interconnections, description
External interfaces are listed in the following figures, with corresponding connectors. The interfaces are
divided into two groups, depending on their location: MAIN UNIT, and EXTENSION UNIT. The
EXTENSION UNIT can be supplied only for IDU 1+1.
.
Figure 81 Main Unit Front
Figure 82 Extension Unit Front
ED 05
3DB 06687 DAAA
110/178
6.1.1.
IDU ODU cable disconnection/connection
Before to disconnect or connect the IDU-ODU cable (at IDU or ODU side) switch off the corresponding
IDU Main Unit or IDU Extension Unit.
Craft Terminal connection
To connect the CT cable (at IDUs interface and/or PC side):
veirfy that the PC is switched of (if switched on, close all running applications, then switch of it)
connect suitable cable to IDUs F interface and PC side
now the PC can be safely switched on
Craft Terminal diconnection
To disconnect the CT cable (at IDUs F interface and/or PC side):
perform the logoff, exiting from the CT applications
close all other running applications, if any
switch off the PC
now the cable can be safely disconnected
ED 05
3DB 06687 DAAA
111/178
(4)
Ethernet user data
(2xRJ45)
(4)
E3/DS3
(2x1.0 - 2.3 female)
(5)
Alarms Housekeeping
(SubD 15 pin female)
(4)
9 -16 E1/DS1 - 32 wires
(SubD 37 pin female)
(6)
NMS_V11 - AUDIO 1
(SubD 15 pin female)
(3)
(1+1) Inter-connection
(SCSI 100 pin female)
(2)
ON-OFF Switch
(1)
Battery input
(SubD 3 pin female)
(7)
Acknowledgement
(push button)
(10)
Telephone (RJ11)
(8)
Test Lamp
(push button)
(11)
OS 10/100 base T
(RJ45)
(9)
Reset
(push button)
(12)
Debug (RJ45)
Leds
(15)
User service channel
(SubD 15 pin female)
(13)
ECT - RS232
(SubD 9 pin female)
(16)
NMS_G703-AUDIO 2
(SubD 15 pin female)
(14)
8 E1/DS1 - 32wires
(SubD 37 pin female)
10 11 12
13
(17)
IDU - ODU
(Connector N female
14
15
16
17
Figure 83 - Main Front / Rear view interconnections IDU
Flash card
Figure 84 Main Rear view (Flash card insertion)
ED 05
3DB 06687 DAAA
112/178
INTER - CONNECTION
(4)
Ethernet user data
(2xRJ45)
(3)
(1+1) Inter - connection
(SCSI 100 pin female)
(4)
E3/DS3
(2x1.0 - 2.3 female)
(1)
Battery input
(SubD 3 pin male)
(4)
9 -16 E1/DS1 - 32 wires
(SubD 37 pin female)
(2)
ON-OFF
Switch
I
Leds
ON ODUW
LT
(5)
Test lamp
(push button)
ESC
(7)
User service channel
(SubD 15 pin female)
I/O (1/8)
(8)
IDU - ODU
(Connector N female)
(6)
8 E1/DS1 - 32 wires (SubD 37 pin female)
Figure 85 - Extension Front view interconnections IDU
Figure 86 - Extension Rear view IDU
ED 05
3DB 06687 DAAA
113/178
Antenna
ODU
to IDU
INTERFACES OF 8E1 IDU 1+0
optional distributor subrack
to ODU
(17)
Power supply
(1)
(14)1-8 E1
(11) OS
(15)User service channels
NMS G.703 + Audio 2
(16)
(5)Alarms - Housekeeping
NMS V.11 + Audio 1
(6)
INTERFACES OF 16E1 IDU 1+0
optional distributor subrack
to ODU
(17)
Power supply
(1)
(11)OS
(4)9-16 E1
(14)1-8 E1
(15)User service channels
NMS G.703 + Audio 2
(16)
(5)Alarms - Housekeeping
NMS V.11 + Audio 1
(6)
INTERFACES OF E3 IDU 1+0
optional distributor subrack
to ODU
(17)
Power supply
(1)
(4) E3
(11) OS
(15)User service channels
NMS G.703 + Audio 2
(16)
(5)Alarms - Housekeeping
NMS V.11 + Audio 1
(6)
INTERFACES OF ETHERNET + 8E1 IDU 1+0
optional distributor subrack
to ODU
Power supply
(1)
(11)OS
1-8 E1
Ethernet
(14)
(4)
(15) User service channels
NMS G.703 + Audio 2
(5) Alarms - Housekeeping
NMS V.11 + Audio 1
Figure 87 1+0 Interconnections view
ED 05
3DB 06687 DAAA
114/178
INTERFACES OF 8E1 IDU 1+1
Power supply
(1)
(6) 1-8 E1
optional distributor subrack
(7) User service channels
to ODU
CH 0
(8)
(3) (1+1) Inter-connection
SCSI 100
to ODU
CH 1
(17)
(11)OS
Power supply
(1)
(14) 1-8 E1
NMS G.703 + Audio 2
(16)
NMS V.11 + Audio 1
(6)
(15) User service channels
(5) Alarms - Housekeeping
Figure 88 1+1 Interconnection view (8E1)
INTERFACES OF 16E1 IDU 1+1
Power supply
(1)
(6) 1-8 E1
optional distributor subrack
(4) 9-16 E1
(7) User service channels
to ODU
CH 0
(8)
(3) (1+1) Inter-connection
SCSI 100
to ODU
CH 1
(17)
Power supply
(1)
(11) OS
NMS G.703 + Audio 2
(16)
(4) 9-16 E1
(14) 1-8 E1
(15) User service channels
(5)Alarms - Housekeeping
NMS V.11 + Audio 1
(6)
Figure 89 1+1 Interconnection view (16E1)
ED 05
3DB 06687 DAAA
115/178
INTERFACES OF E3 IDU 1+1
Power supply
(1)
optional distributor subrack
(4) E3
(7) User service channels
to ODU
CH 0
(8)
(3) (1+1) Inter-connection
SCSI 100
to ODU
CH 1
(17)
Power supply
(1)
(11) OS
NMS G.703 + Audio 2
(16)
(4) E3
(15) User service channels
NMS V.11 + Audio 1
(6)
(5) Alarms - Housekeeping
Figure 90 Interconnection view (E3)
INTERFACES OF Ethernet + 8E1 IDU 1+1
Power supply
(1)
(6) 1-8 E1
optional distributor subrack
(7)User service channels
to ODU
CH 0
(8)
(3) (1+1) Inter-connection
SCSI 100
to ODU
CH 1
(17)
Power supply
(1)
NMS G.703 + Audio 2
(16)
(14) 1-8 E1
(4) Ethernet
(11) OS
(15)User service channels
(5)Alarms - Housekeeping
NMS V.11 + Audio 1
(6)
Figure 91 Interconnection view (Ethernet
NOTE: Figures in parentheses correlate to Fig. Ref. Column in Table 18, page 117 and Table 21, page
121.
The IDU is offered in two different configurations (1+0 and 1+1 configuration):
ED 05
3DB 06687 DAAA
116/178
6.2.
Numbering and functions referred to the Connection Points
Table 18 - Numbering and functions referred to the Connection Points (Main)
Ref
FROM MAIN BOARD
TO
Or
TO
Figure
84
(1)
Battery input
T.R.U
Power Supply
Battery
or
(4)
9-16 E1/DS1 32wires (Plug-in)
Extension (1+1)
Station Distributor
(4)
E3/DS3 (Plug-in)
Extension (1+1)
Station Distributor
(4)
Ethernet user data (Plug-in)
Extension (1+1)
Station Distributor
(5)
Alarms Housekeeping
Station Distributor
(6)
NMS_V11 AUDIO 1
Adjacent AWY N.E. Access NMS_V11- AUDIO 1 (EOW)
(10)
Telephone
(11)
OS 10/100 base T
(12)
Debug
Only for internal use
(13)
ECT RS 232
PC - Craft Terminal
(14)
8 E1/DS1 32 wires
(15)
User Service Channel
(16)
NMS_G703 AUDIO 2
(17)
Connector N
Handset
Craft Terminal
or
T.M.N.
Customer Distributor (CDF)
Station Distributor
Adjacent AWY N.E. Access NMS_G703 - Audio 2 (EOW)
ODU
NB: (6) (16) NMS INTERFACE AWY-MELODIE (see Figure 98 on page 130)
ED 05
3DB 06687 DAAA
117/178
Table 19 - Numbering and functions referred to the Connection Points (Extension)
Ref
Figure
85
FROM EXTENSION BOARD
TO
(1)
Battery input
T.R.U.
(3)
1+1 Inter-connection
Main
(4)
9-16 E1/DS1 32wires (Plug-in)
Main
(4)
E3/DS3 (Plug-in)
Main
(4)
Ethernet user data (Plug-in)
Main
(6)
8 E1/DS1 32 wires
Main
(7)
User Service Channel
Main
(8)
Connector N
ODU
ED 05
Or
To
Power Supply Battery
3DB 06687 DAAA
118/178
Table 20 - Numbering and functions referred to the Connection Points (1+1 version)
Ref
Figure
84
Ref
Figure
85
Main Board
Extension Board
(1)
(1)
Battery input
Battery input
(3)
(3)
1+1 Inter-connection
Extension - 1+1 Inter-connection
(4)
(4)
9-16 E1/DS1 32wires (Plug-in)
Extension - 9-16 E1/DS1
32wires (Plug-in)
(4)
(4)
E3/DS3 (Plug-in)
Extension E3/DS3 (Plug-in)
(4)
(4)
Ethernet user data (Plug-in)
Extension Ethernet user data
(Plug-in)
(5)
Alarms Housekeeping
(6)
NMS_V11 AUDIO 1
(10)
Telephone
(11)
OS 10/100 base T
(12)
Debug
(13)
ECT RS 232
(14)
(6)
8 E1/DS1 32 wires
(15)
(7)
User Service Channel
(16)
(17)
ED 05
To
T.R.U.
or To
PSU
Extension 8 E1/DS1 32 wires
Extension User Service Channel
NMS_G703 AUDIO 2
(8)
Connector N
Connector N
ODU
3DB 06687 DAAA
119/178
6.3.
Summary and type connectors usage
Interface
Connector
Type
Paragraph
SubD3
Male
6.4.18
Two position
switch
6.4.19
(1)
Battery Input
(2)
ON OFF Switch
(3)
1+1 Inter-connection
SCSI 100
pin
Female
(4)
9-16 E1/DS1 32 wires
SubD37
Female
6.4.3
(4)
E3/DS3
2x(1.0/2.3)
Female
6.4.10
(4)
Ethernet user data
2xRJ45
IDU
(5)
Alarms Housekeeping
SubD15
Female
6.4.9
Main Unit
(6)
NMS_V11 AUDIO 1
SubD15
Female
6.4.5
(7)
M - Acknowledgment
Push Button
6.4.11
(8)
LT - Test Lamp
Push Button
6.4.11
(9)
R Reset
Push Button
6.4.11
(10)
TPH Telephone
RJ11
6.4.15
(11)
OS 10/100 base T (or ECT)
RJ45
6.4.12
(12)
Debug
RJ45
6.4.11
(13)
ECT-RS232
SubD9
Female
6.4.13
(14)
8E1/DS1 32 wires
SubD37
Female
6.4.3
(15)
User Service Channel
SubD15
Female
6.4.8
(16)
NMS_G703 AUDIO 2
SubD15
Female
6.4.6
(17)
IDU-ODU Cable
Leds
6.4.12
6.4.16
N 6
Led
6.4.11
Connector
Type
Paragraph
SubD 3
Male
6.4.18
Two position
switch
6.4.19
Only for 1+1 system
Extension Unit
IDU
Interface
(1)
Battery Input
(2)
ON OFF Switch
(3)
1+1 Inter-connection
SubD37
Female
6.4.3
(4)
9-16 E1/DS1 32 wires
SubD37
Female
6.4.3
(4)
E3/DS3
2x(1.0/2.3)
Female
6.4.10
(4)
Ethernet user data
(5)
LT - Test Lamp
Push Button
6.4.11
(6)
8E1/DS1 32 wires
SubD37
Female
6.4.3
(7)
User Service Channel
SubD15
Female
6.4.8
N 2
ON/ODUW
6.4.11
Leds
2xRJ45
NB: (6) (16) IDU MAIN UNIT NMS INTERFACE AWY-MELODIE (see Figure 98 on page 130)
ED 05
3DB 06687 DAAA
120/178
6.4.
Suggested cabling
Table 21 - Suggested cabling
Cable Type
Connection type
Alcatel P/N
100 wire SCSI cable for 1+1
3DB06592ABXX
37 wires 8E1/DS1 cable for 1+1 (Split Cable)
3CC13659AAXX
E3/DS3 cable for 1+1
Male
3DB06593AAXX
SubD-15 Male
3DB06594AAXX
Connection cable 24 V 3X10
SubD-3
Male
3CC08212AAAA
Connection Cable 48 V (3X4)
SubD-3
Male
3CC08211AAAA
User Service Channel cable for 1+1
FILOTEX COAX CABLE 50 OHM
CABLE 8XE1/DS1 IDU/DISTR-1.0/2.3-75 OHM UNB
1AC001100022
1.0/2.3
Male
3DB10008AAXX
CABLE 8XE1/DS1 IDU/DISTR - 120 OHM BAL
3DB10007AAXX
1.6/5.6
Male
3CC07885ABAA
120 ohm
3CC07658AAAB
BNC Male 75 ohm
3CC07759ABAA
HA-HC/SC cable L=15m
SubD-15
Male
3DB05594AAXX
NMS/AUDIO CABLE L=1.6 m
SubD-15
Male
3DB05922AAXX
NMS/AUDIO CABLE L=6.4 m
SubD-15
Male
3DB05923AAXX
CABLE 8XE1/DS1 IDU/DISTR 1.6/5.6-75 OHM UNB 2m
CABLE 8XE1/DS1 IDU/DISTR - 120 OHM 2m
CABLE 8XE1/DS1 IDU/DISTR-BNC-75 OHM UNB 2m
NMS INTERFACE AWY-MELODIE IDU L= 1.6m
3DB10063AAAA
NMS INTERFACE AWY-MELODIE IDU L= 6.4
3DB10064AAAA
2MHz 75OHM cable L=1m
1AC001100013
SubD-9
Female
1AB054120027
SubD-37
Male
3DB05588AAAA
Male
1AB061220005
Male Coax Connector 1.6/5.6
Male
1AB009870002
Male Coax Connector BNC 75 ohm
Male
1AB006420060
Panel Coax Connector 1.0/2.3
Female
1AB009790019
Panel Coax Connector 1.6/5.6
Female
1AB002130006
Panel Coax Connector BNC 75 ohm
Female
RS232CT cable
75 OHM COAX CABLE 8XE1/DS1 IDU/DISTR
NO CONNECTORS L=10M
Male Coax Connector 1.0/2.3
120 OHM 8x2 twisted pair cable
1AB006020076
1AC011980001
100 OHM CABLE for 8XDS1
1AC021980001
120 OHM Cable L904/16p lg 15m w connector
3CC08951ACAA
Power Supply connection 24V (3X2.52)
3CC0829AAAA
Power Supply connection 48V (3X1.52)
3CC08165AAAA
Ethernet crossover cable L=2m
3DB05021AAAA
Ethernet crossover cable L=6.4
3DB14051AAAA
Ethernet cable L= 2m
3DB14046AAAA
Ethernet cable L= 6.4m
3DB14050AAAA
ESC AWY connection L=1.6m
3DB10087AAAA
ESC AWY connection L=6.4
3DB10088AAAA
ED 05
3DB 06687 DAAA
121/178
6.4.1.
Split Cable
(1+0) Main Unit
SUB D 37/ 15 male
Extension Unit
SUB D 37/ 15 male
SUB D 37/ 15 male
Special Split Cable
for E1/DS1Tributaries (37pins)
and for User Service Channels (15pins)
User
Figure 92 E1 / DS1 and User Service Channel Split-Cable
ED 05
3DB 06687 DAAA
122/178
Figure 93 Cable connections (example)
ED 05
3DB 06687 DAAA
123/178
6.4.2.
Inter- connection Main Extension flat cable
In 1+1 configuration the two subracks (Main and Extension) are inter-connected by means of auxiliary flat
cable (100-wires SCSI)
Inter - connector
(100 wire SCSI)
Inter connector
(100 wire SCSI)
Figure 94-1+1 Inter-connection
ED 05
3DB 06687 DAAA
124/178
6.4.3.
I/O 1 through 8 and I/O 9 through 16
18
37
19
8 E1/DS1 - 32 wires
(SubD 37 pin female)
8 E1/DS1- 32 wires
(SubD 37 pin female)
18
I/O (9/16)
9-16 E1/DS1 - 32 wires
(SubD 37 pin female)
19
37
9-16 E1/DS1- 32 wires
(SubD 37 pin female)
Figure 95 - I/O 1 through 8 and 9 through16 connections (Main Extension)
16E1 16DS1
Two 37-pin SubD connectors allow for the connection of 16 tributaries.
For E1 tributaries the same input and output wires are reused for 120 balanced and 75 unbalanced
(see Table 21, page 121 and Table 22, page 126).
For DS1 tributaries one impedance is foreseen (100 balanced).
NOTE: to reduce the interferences phenomena one cable (8 pair twisted cable) is used to connect
all TX pins (A) and other one cable (8 pair twisted cable) is used to connect all RX pins (B).
See the Table 22/Table 23 on page 126.
See the Table 24 Distributor Subrack and Cable type on page 127
ED 05
3DB 06687 DAAA
125/178
Table 22 - I/O (1 through 8) connections
Description
Reserved
IN+Trib. 1
IN+Trib. 2
IN+Trib. 3
IN+Trib. 4
IN+Trib. 5
IN+Trib. 6
IN+Trib. 7
IN+Trib. 8
GND
Reserved
OUT+Trib. 1
OUT+Trib. 2
OUT+Trib. 3
OUT+Trib. 4
OUT+Trib. 5
OUT+Trib. 6
OUT+Trib. 7
OUT+Trib. 8
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Description
Reserved
IN-Trib. 1
IN-Trib. 2
IN- Trib. 3
IN- Trib. 4
IN- Trib. 5
IN- Trib. 6
IN- Trib. 7
IN- Trib. 8
Pin #
20
21
22
23
24
25
26
27
28
Reserved
29
OUT-Trib. 1
OUT-Trib. 2
OUT-Trib. 3
OUT-Trib. 4
OUT-Trib. 5
OUT-Trib. 6
OUT-Trib. 7
OUT-Trib. 8
30
31
32
33
34
35
36
37
Cable
See par. 6.4 on
page 121
A
(TX)
B
(RX)
Table 23 - I/O (9 through 16) connection
Description
Reserved
IN+Trib. 9
IN+Trib. 10
IN+Trib. 11
IN+Trib. 12
IN+Trib. 13
IN+Trib. 14
IN+Trib. 15
IN+Trib. 16
GND
Reserved
OUT+Trib. 9
OUT+Trib. 10
OUT+Trib. 11
OUT+Trib. 12
OUT+Trib. 13
OUT+Trib. 14
OUT+Trib. 15
OUT+Trib. 16
ED 05
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Description
Reserved
IN-Trib. 9
IN-Trib. 10
IN-Trib. 11
IN-Trib. 12
IN-Trib. 13
IN-Trib. 14
IN-Trib. 15
IN-Trib. 16
Pin #
20
21
22
23
24
25
26
27
28
Reserved
29
OUT-Trib. 9
OUT-Trib. 10
OUT-Trib. 11
OUT-Trib. 12
OUT-Trib. 13
OUT-Trib. 14
OUT-Trib. 15
OUT-Trib. 16
30
31
32
33
34
35
36
37
Cable
See par. 6.4 on
page 121
A
(TX)
B
(RX)
3DB 06687 DAAA
126/178
6.4.4.
Mini Distributor connection
The user ports are implemented on two 37way connectors: for the 2 Mbit/s tributary ports. The user must
choose from the configurations listed below.
Distributor Subrack
Cable type
Distributor Subrack for 1.6/5.6 (3CC08061AAAA).
(Cable8X1/DS1 IDU/DISTR-1.6/5.6 75 ohm UNB
3CC07885ABAA)
Distributor 1U Subrack for 120 ohm NO EMC
(3CC08062AAAA).
(Cable 8XE1/DS1 IDU/DISTR- 120 ohm
3CC07658AAAB)
Distributor 3U Subrack for 120 ohm EMC
(3CC07810AAAA).
(Cable 8XE1/DS1 IDU/DISTR- 120 ohm
3CC07658AAAB)
Distributor Subrack for BNC (3CC08061ABAA).
(Cable8X1/DS1 IDU/DISTR-BNC 75 ohm UNB
3CC07759ABAA)
Table 24 Distributor Subrack and Cable type
For more information see USER MANUAL/TECHNICAL HANDBOOK 9400 AWY Rel.2.0
ED 05
3DB 06687 DAAA
127/178
6.4.5.
NMS V11 - AUDIO 1 (EOW)
NMS_V11 - AUDIO 1
(SubD 15 pin female)
15
(NMS_V11+Audio1) interface has 9 pins dedicated to NMS and 6 pins dedicated to EOW analog party
line.
NMS_V11 channel is a 64Kb/s co directional and TX and RX are totally asynchronous.
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Description
RS422 data in (+)
RS422 clock in (+)
RS422 data out (+)
RS422 clock out (+)
GND NMS
AUDIO 1 (EOW) signal from user (+)
AUDIO 1 (EOW) signal to user (+)
GND Audio
RS422 data in (-)
RS422 clock in (-)
RS422 data out (-)
RS422 clock out (-)
AUDIO 1 (EOW) signal from user (-)
AUDIO 1 (EOW) signal to user (-)
Not used
Cable
See par. 6.4
on page 121
Figure 96 - NMS V11 Audio1 (EOW) connections
ED 05
3DB 06687 DAAA
128/178
6.4.6.
NMS G703 + Audio 2 (EOW)
NMS_G703 - AUDIO 2
(SubD 15 pin female)
15
(NMS_G703 + Audio2) interface has 5 pins dedicated to NMS and 6 pins dedicated to EOW analog party
line.
NMS_G703 channel is a 64Kb/s; its working mode can be selected between:
DTE G703 data in and G703 data out have to be synchronous, G703 data out being the slave,
Asynchronous: G703 data in and G703 data out are totally asynchronous.
Pin #
Description
1
2
3
4
5
G703 data in (+)
Not used
G703 data out (+)
Not used
GND NMS
AUDIO 2 (EOW) signal from user (+)
7
8
9
10
11
12
13
14
15
AUDIO 2 (EOW) signal to user (+)
GND Audio
G703 data in (-)
Not used
G703 data out (-)
Not used
AUDIO 2 (EOW) signal from user (-)
AUDIO 2 (EOW) signal to user (-)
Not used
Cable
See par. 6.4
on page 121
Figure 97 - NMS_G703 + Audio2 (EOW) connections
ED 05
3DB 06687 DAAA
129/178
6.4.7.
NMS INTERFACE AWY-MELODIE
NMS INTERFACE AWY-MELODIE
(SubD 15 pin female)
15
NOTE:
AWY SIDE:
in this connection there are both signal Audio (party-line) and Supervision G703 or
V11 in alternative
MELODIE SIDE:
the party line connection is stand-aloneas stand-alone the NMS connector.
3DB10063AAAA NMS INTERFACE AWY-MELODIE IDU L= 1.6m
3DB10064AAAA NMS INTERFACE AWY-MELODIE IDU L= 6.4m
MELODIE SIDE (9 PINS)
AUDIO
AWY IDU- SIDE (15 PINS)
NMS
Figure 98 NMS INTERFACE AWY-MELODIE
ED 05
3DB 06687 DAAA
130/178
6.4.8.
Service Channel
User service channel external interface (SubD15) is located both 9400AWY Main and Extension board.
A special user service channel cable (linking externally the SubD15 connectors on Main and Extension
subrack) is used to support EPS protection in (1+1) configuration; no wires are thus necessary to be
exchanged on the auxiliary (1+1) flat cable.
15
User service channel
(SubD 15 pin female)
User Service channel
(SubD 15 pin female)
SERVICE channel provides external access for auxiliary channel by means of a 15-pin SubD 15 female
connector.
Pin #
2
9
3
10
4
11
5
12
6
13
7
14
8
15
1
Signal
COD_RX +
COD_RX COD_TX +
COD_TX RX_ASY
TX_ASY
CC_RX +
CC_RX RX_CK +
RX_CK CC_TX +
CC_TX CC_TCK +
CC_TCK +
GND
Meaning
G703_64K_RX +
G703_64K_RX G703_64K_TX +
G703_64K_TX V24/V28 asynchronous_RX
V24/V28 asynchronous_TX
V11_64K_DATA_RX +
V11_64K_DATA_RX V11_64K_CLOCK_CK +
V11_64K_CLOCK_CK V11_64K_DATA_TX +
V11_64K_DATA_TX V11_64K_CLOCK_TCK +
V11_64K_CLOCK_TCK Ground
Direction
INPUT
INPUT
OUTPUT
OUTPUT
INPUT
OUTPUT
INPUT
INPUT
BID
BID
OUTPUT
OUTPUT
OUTPUT
OUTPUT
/
Cable
See
par.
6.4 on
page
121
Figure 99 - SERVICE CHANNEL connections (Main Extension)
ED 05
3DB 06687 DAAA
131/178
6.4.9.
Housekeeping Alarms
15
Alarms Housekeeping
(SubD 15 pin female)
The Housekeeping Alarms- SubD15 connector is divided into:
3 summarizing discrete alarms equipment outputs;
4 housekeeping controls equipment outputs;
6 housekeeping alarms equipment inputs;
1 common wire dedicated to equipment outputs;
1 common wire dedicated to equipment inputs.
Pin
6
13
7
14
8
15
4
11
5
12
9
Connector
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2
M2
1
2
3
10
M2
M2
M2
M2
Signal
HK_I1
HK_I2
HK_I3
HK_I4
HK_I5
HK_I6
HK_O1
HK_O2
HK_O3
HK_O4
Direction
INPUT
INPUT
INPUT
INPUT
INPUT
INPUT
OUTPUT
OUTPUT
OUTPUT
OUTPUT
Cable
See par. 6.4
on page 121
COM -COMMON WIRE
(FOR ALARM OUTPUTS)
A_1
A_2
A_3
GROUND (ALARM INPUT
COMMON PONIT)
OUTPUT
OUTPUT
OUTPUT
/
Figure 100 - Housekeeping- Alarms- connections
ED 05
3DB 06687 DAAA
132/178
6.4.10.
E3 - DS3
E3/DS3
(2x1.0 - 2.3 female)
E3/DS3 (2x1.0-2.3 female)
Figure 101 - E3 DS3 Interface connections (Main Extension)
Two 1.0 /2.3 Siemens adapter connectors are dedicated to the E3/DS3 input/output; the impedance is
always 75 unbalanced. The first adapter is a 100 cm cable with a 1.0/2.3 "locking" connector and a BNC
connector (cod. 041.992.634), the second adapter is a 100 cm cable with a 1.0/2.3 "locking" connector and
a 1.6/5.6 connector (cod. 041.992.635).
ED 05
3DB 06687 DAAA
133/178
6.4.11.
M, LT, LEDs (housekeeping, Summarizing)
LEDs
ON
RDI
MIN
LDI
MAJ
EOW
M - Acknowledgement (Push button)
LT - Test Lamp (Push button)
ODUW
ATTD
R - Reset (Push button)
LEDs
LT
ON
ODUW
Figure 102 - M, LT and LEDs meanings
The M pushbutton turns off the LEDs alarms.
The LT (lamp test) pushbutton verifies if the LEDs alarms are turn on.
The following LEDs are present on the front panel of the Main and Extension Board
LED meanings
POS.
1
2
3
4
5
6
7
8
ED 05
LED
ON
RDI
MIN
EOW
ODUW
LDI
MAJ
ATTD
MEANING
Power on
Remote Defect Indication
Minor alarm
Engineering Order wire / RPS position
ODU working
Local Defect Indication
Major Alarm
Attended
COLOUR
Green
Red
Red
Busy (Yellow), FREE (Green) / RPS on (Green)
Green
Red
Red
Yellow
3DB 06687 DAAA
134/178
6.4.12.
OS DEBUG
Debug (RJ45)
OS (or ECT)10/100 base T
(RJ45)
Figure 103 OS - DEBUG connections cable pin out table
These connections are directly made on the RJ45 connectors mounted on the main unit, and use the
10/100 base T interface.
Ethernet pin out cable
M2
M2
M1
RJ45
RJ45
RJ45
Signal
Color used
CABLE
Eth1
CT
MAIN side
Eth2
side
1
Tx +
White/Orange
1
3
2
Tx -
Orange
Rx +
White/Green
Blue
White/Blue
Green
White/Brown
Brown
Rx -
See par.
6.4 on
page 121
Pins 4,5,7 and 8 are not used
CT Ethernet cable
ED 05
3DB 06687 DAAA
135/178
6.4.13.
CT access
5
ECT - RS232
(SubD 9 pin female)
9
In Figure 104 on page 136 is detailed the pinout for the RS 232 - 9 pins connector to interconnect the
Personal Computer to the CT .
RS 232
IDU MAIN side
1
RS 232 (PC side)
1
Figure 104 - CT connections
6.4.14.
R - Reset pushbutton
This pushbutton resets the unit software.
ED 05
3DB 06687 DAAA
136/178
6.4.15.
TPH Telephone Handset
TPH - Telephone handset
(RJ11)
1AF12831AAAA
RJ11 Connector
ED 05
3DB 06687 DAAA
137/178
6.4.16.
IDU ODU connections
IDU - ODU
(Connector N female)
IDU - ODU
(Connector N female)
Figure 105 - IDU ODU interconnections (Main Extension)
The transceiver inside the ODU module is connected to the IDU side through an IDU-ODU interconnecting
50 ohm coaxial cable (1AC001100022). The connector used is a N male connector (1AB095530021).
In order to assemble the connector to the coaxial cable, refer to the leaflet enclosed into the supplied
connector beg, however hereafter are reported some of the main connector assembling descriptions .
6.4.16.1. Connector N Torque Tightening
NOTE: TORQUE Tightening Connector N
1) Connector N (Male) on the IDU
2) Connector N (Male) on the ODU
3) Connector N (Male) on the external discharger
2 Nm
3 Nm
3 Nm
6.4.16.2. Maximun length
CODE
1AC00110022
ED 05
DESCRIPTION
Filotex coax cable 50 ohm
MAX LENGHT
16E1
250 m
3DB 06687 DAAA
16DS1
150 m
138/178
6.4.17.
50 Ohms connector assembling
NB:
Hereafter we show some example of connector assembling , however each connector is delivered
with its own description leaflet enclosed into the connector delivering plastic bag.
6.4.17.1. ROSENBERGER CONNECTOR MOUNTING
Straight
50 Ohms connector assembling description
1)
Strip 15 mm of outer insulation from the cable and comb out the braid.
2)
Fit the nut, washer, flat gasket and braid clamp onto the cable, then fold back the braid over the
braid clamp and cut away the excess. Strip the core of the cable to the dimensions opposite.
3)
Fit the center contact fully home on the core of the cable. Crimp with DANIELS M225/5-01 tool
fitted with jaws Y215P (hex:.128 across flats). If not possible, solder. CAUTION: DO NOT MELT
THE CABLE INSULATION.
4)
About the gasket and washer against the braid clamp then offer up the end of the cable into the
body of the connector making sure that the contacts mate correctly with each other. Screw the
nut into the body of the connector (torque: 5 Nm). The connector is now ready for use.
Figure 106 - Details for assembling N connector to coaxial cable
ED 05
3DB 06687 DAAA
139/178
6.4.17.2. ROSENBERGER CONNECTOR MOUNTING -
90 Male
50 Ohms connector assembling description
4
5
6
7
Prepare the cable according to the diagram.
Cut the cables jacket ( 12 mm + 3 mm ) 15 mm long.
Disassemble the connector as shown in the figure.
Slide nut A, washer B and gasket C onto the cable.
Push clamp D over the braid and fold the braid back over the clamp.
Insert the prepared cable fully into the connector body E and position
the inner conductor of the cable in the slot of the central pin.
Thread nut A and tighten down with torque 4 Nm.
Solder central pin to the inner conductor of the cable.
Place washer F and tighten down cover G into the rear aperture of the
connector body.
NB. Coupling torque: 15N.m to 35N.m.
ED 05
3DB 06687 DAAA
140/178
6.4.18.
Power Supply connector, On / Off switch
Battery (1)
Battery (1)
Figure 107 Power Supply Connector
The PSU is a plug-in of the IDU Main/extension Board.
It is a module including DC/DC converters and filters. It is plugged onto the main board by means of
suitable connectors. Three versions exist:
1)
48Vdc to 60Vdc
20%;
2)
24Vdc
-20% +50%
according to the IDU MAIN UNIT and IDU EXTENSION UNIT.
ED 05
3DB 06687 DAAA
141/178
SAFETY RULES
Due to possible very high currents in case of short-circuit at the battery power input; it is essential that
the battery power distribution line be provided with a short circuit back-up protection with adequate
breaking capacity
Max rating of branch circuit protection is 15A (USA/CANADA) or 16A (Others)
Battery
Pin
Function
A1
+ BATTERY
A2
GROUND
A3
- BATTERY
Cable
See par. 6.4 on
page 121
Figure 108 - Power supply connections
6.4.19.
ON-OFF switch
Powers the unit on and off.
ON OFF Switch
Figure 109 ON-OFF Switch
ED 05
3DB 06687 DAAA
142/178
7. CAPACITY EXTENSION
9400 AWY R.2.0.4 can be provided with transceiver able to support 32E1 capacity even if the IDU supports
16E1 maximun.
The above could be usefully in case of successive capacity extensions. If the case, pay attention to the
following:
ED 05
IDU-ODU (Filotex Coax Cable 50 ohm)
With Filotex coax cable there limitation in the maximum length (150m instead of 250m for ETSI
version); a more performant cable could be necessary to cover specific cases
IDU installation in Rack
To migrate from 16E1 to 32E1 the IDU must be substituited with other subracks that can require
more room (see related documentation)
For an easy successive extension the eventual additional room needed should be left free.
3DB 06687 DAAA
143/178
ANNEXES
W.T.D. Rack installation
Mechanical installation
Installation has been subdivided into the following phases:
-
Rack Positioning and Fastening
Fixing the rack to floor using expansion bolts or Fixing to floating floor;
T.R.U. fastening to W.T.D rack.
Rack Positioning and Fastening
Proceed as follows:
-
Refer to the plant documentation to see rack row assignment
Fasten the rack to the station structure according to one of the following procedures:
Fixing the rack to floor (see paragraph 2.2.3)
Fixing the rack to floating floor (see paragraph 2.2.4)
Fixing the rack to floor using expansion bolts
(See Figure 110 on page 145)
-
Mount the rack in a vertical position in the desired place.
Mark the baseplate with six holes (1) to be drilled on the floor
Temporarily remove the rack and drill the holes at the points drawn on the floor (see Figure 111 on
page 146).
Place the inserts into the holes
Secure the expander bolts to the floor through the baseplate holes.
ED 05
3DB 06687 DAAA
144/178
20
EXPANSION ANCHOR M8x40
NOTES:
All dimensions are in millimetres
* Fixable max thickness
12**
** Diameter drill
Figure 110 - Fixing the W.T.D. rack using expansion anchors
ED 05
3DB 06687 DAAA
145/178
142 mm
30 mm
30 mm
98 mm
149 mm
300 mm
149 mm
DRILL HOLES
Figure 111 - rack - Drill Holes for Anchoring to the Floor (single rack)
ED 05
3DB 06687 DAAA
146/178
Fixing to floating floor
The drilling mask is the same used for concrete floor fastening (
Figure 111 on page 146). In this case a hole must be created for the cables coming from the bottom
according to Figure 112 on page 147. The rack fastening is to be mounted on the concrete floor below
using a suitable stud as shown in
Figure 113 on page 148.
Using the row layout drawing, mark out the cable entry areas in the floor tiles and cut out with a jigsaw.
Remember that the beginning of the row must be approved by the customer.
N.B.
Unused or incompletely used cable entry areas should be blocked off with foam rubber.
598
149
149
300
61.25
96.25
CABLE ENTRY
AREA
35
30
130
30
297.25
35
80
106
81
FIBER DUCTS
26
Figure 112 - rack - Floor tile drilling template
ED 05
3DB 06687 DAAA
147/178
HEX NUT
LOCKWASHER
FLAT WASHER
BOTTOM
STUD
Rack base
FLAT WASHER
LOCKWASHER
HEX NUT
Computer Floor
STUD
HEX NUT
LOCKWASHER
Concrete Floor
FLAT WASHER
EXPANSION PLUG
Figure 113 - rack - Example of securing rack assembly to computer floor
ED 05
3DB 06687 DAAA
148/178
T.R.U. fastening to the W.T.D rack
SAFETY RULES
T.R.U. fastening to the rack guarantees the connection to the protection ground in that the rack is wired to
the station protection ground.
See Figure 114on page 149.
Fix the T.R.U. (1) to the rack by inserting screws (2) into the holes of the adapter (4), screw them into the
relative holes on side-wall (3).
Figure 114 - rack - T.R.U. fastening to the rack
Figure 115 - W.T.D rack - Front plate 6 circuit breakers
Electrical connections
Electrical Installation has been subdivided into the following phases:
ED 05
Protection ground Connections
3DB 06687 DAAA
149/178
Power supply connection
Protection ground Connections
The rack must be grounded by means of a connection to the protection ground terminal of the site electrical
plant.
SAFETY RULES
The rack must be connected to the protection ground before performing any other
electrical connection.
In Figure 116 on page 149 is shown the connection of the ground on the topside of the rack.
The rack is grounded to the station through a 16 to 25 mm2 (1 to 2 AWG) section cable (1) terminated
onto the cable terminal lug (2).
Figure 116 - Rack - Ground connections
ED 05
3DB 06687 DAAA
150/178
AWY supply voltage & Grounding section cables
System
Cables length
BB Unipolar cable section Power Supply
AWY 1+0
AWY 1+1
Up to 20 m
Up to 20 m
2 x 1.5 mm2 shielded
2 x 1.5 mm2 shielded
1 x 3 mm2
1 x 3 mm2
2 x 16 mm2
2 x 16 mm2
Grounding Cable section
1 X > =16 mm2
1 X > =16 mm2
TRU
1 X > =16 mm2
1 X > =16 mm2
BB Unipolar cable section Grounding Cable
TRU Unipolar cable section Power Supply
TRU 16 circuit breakers full equipped with AWY sys.
Unipolar cable section Grounding Cable
RACK Unipolar cable section Grounding Cable
NB: For WTD rack the TRU doesnt require any cable ground connection to the rack.
ED 05
3DB 06687 DAAA
151/178
Annex A
CABLE CODE INTERCONNECTIONS DESCRIPTION
CODE
Type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
3DB05021AAAA
3DB05922AA**
3DB05923AA**
3DB10063AAAA
3DB10064AAAA
3DB10087AAAA
3DB10088AAAA
3DB10089AAAA
3DB10090AAAA
3DB10091AAAA
3DB10092AAAA
3DB10093AAAA
3DB10094AAAA
3DB10095AAAA
3DB10096AAAA
3DB10100AAAA
3DB10101AAAA
3DB14051AAAA
3CC52119AAAA
3CC52120AAAA
3CC52121AAAA
3CC52130AAAA
3CC52131AAAA
3CC52132AAAA
RJ45
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
RJ45
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
Sub-D
DESCRIPTION
M1
M2
M3
n pin n pin n pin
8
8
15
15
15
15
15
9
9
15
9
9
15
15
15
15
15
9
15
9
15
25
15
25
15
9
15
9
15
15
15
15
37
9
9
15
15
8
8
15
9
9
15
9
9
37
9
25
15
9
15
9
15
9
Lenght
2m
1,6m
6,4m
1,6m
6,4m
1,6m
6,4m
1,6m
6,4m
1,6m
6,4m
6,4m
1,6m
6,4m
1m
1,6m
6,4m
1m
Annex B - Table 1 Cable code interconnections
ED 05
3DB 06687 DAAA
152/178
Cable 3DB05922AAAA (L.= 1.6m) or 3DB05923AAAA (L.=6,4m)
M2
M1
1
9
2
10
3
11
4
12
5
To cut
6
13
7
14
8
To cut
Sub-D
15pins Male
Sub-D
15pins Male
CONNECTION CABLE
Pair colours
Pair number
Blue
1
Withe
Violet
2
Turquoise
Orange
3
Withe
Violet
4
Turquoise
Green
5
Withe
Violet
6
Turquoise
Brown
7
Withe
Violet
8
Turquoise
M1
M2
3
11
4
12
1
9
2
10
5
To cut
7
14
6
13
8
To cut
Annex B - Table 2 Connections Cable 3DB05922AAAA (L.= 1.6m) or 3DB05923AAAA (L.=6,4m)
ED 05
3DB 06687 DAAA
153/178
Cable 3DB05021AAAA (L.= 2m) or 3DB14051AAAA (L.=6,4m)
M2
M1
RJ45 8pins
RJ45 8pins
Pair
Wire A
1
2
3
4
White/Blue ring
White/Orange ring
White/Green ring
White/Brown ring
CONNECTION CABLE
M1
M2
Wire B
Pin N
Pin N
1
3
Blue
3
1
Orange
4
4
Green
7
7
Brown
M1
Pin N
2
6
5
8
M2
Pin N
6
2
5
8
Annex B - Table 3 Connecton Cable 3DB05021AAAA (L.= 2m) or 3DB14051AAAA (L.=6,4m)
ED 05
3DB 06687 DAAA
154/178
Cable 3DB10095AAAA (L.= 1.6m) or 3DB10096AAAA (L.=6,4m)
Sub-D
15pins
Male
M1
2
9
4
11
6
13
3
10
5
12
1
To cut
To cut
To cut
To cut
To cut
M2
M1
CONNECTION CABLE
Pair colours
Pair number
Blue
1
Withe
Orange
2
Withe
Green
3
Withe
Brown
4
Withe
Grey
5
Withe
Blue
6
Red
Orange
7
Red
Green
8
Red
Sub-D
15pins
Male
M2/M1
M2-11
M2-3
M2-9
M2-1
M2-10
M2-2
M1-5
M1-12
M1-3
M1-10
M2-5
To cut
To cut
To cut
To cut
To cut
Annex B - Table 4 Connection Cable 3DB10095AAAA (L.= 1.6m) or 3DB10096AAAA (L.=6,4m)
ED 05
3DB 06687 DAAA
155/178
Cable 3DB10087AAAA (L.= 1.6m) or 3DB10088AAAA (L.=6,4m)
Sub-D
15pins
Male
M2
Sub-D
15pins
Male
ANNEX B - Figure 1 - Back to back cord connection
M1
2
9
3
10
4
1
5
12
6
13
7
14
8
15
11
To cut
M1
ESC - AWY
CONNECTION CABLE
Pair colours
Pair number
Blue
1
Withe
Violet
2
Turquoise
Orange
3
Withe
Violet
4
Turquoise
Green
5
Withe
Violet
6
Turquoise
Brown
7
Withe
Violet
8
Turquoise
M2
3
10
2
9
11
1
7
14
8
15
5
12
6
13
4
To cut
Annex B - Table 5 Connection Cable 3DB10087AAAA (L.= 1.6m) or 3DB10088AAAA (L.=6,4m)
ED 05
3DB 06687 DAAA
156/178
Cable 3DB10089AAAA (L.= 1.6m) or 3DB10090AAAA (L.=6,4m)
M2
M1
Sub-D 9pins Male
M1
7
14
8
15
5
12
6
13
1
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Sub-D 15pins Male
CONNECTION CABLE
Pair colours
Pair number
Blue
1
Withe
Orange
2
Withe
Green
3
Withe
Brown
4
Withe
Grey
5
Withe
Blue
6
Red
Orange
7
Red
Green
8
Red
M2
1
6
7
2
8
4
9
5
3
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Annex B - Table 6 Connection Cable 3DB10089AAAA (L.= 1.6m) or 3DB10090AAAA (L.=6,4m)
ED 05
3DB 06687 DAAA
157/178
Cable 3DB10091AAAA (L.= 1.6m) or 3DB10092AAAA (L.=6,4m)
Sub-D
25pins
Male
M2
M1
5
12
6
13
7
14
8
15
To cut
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Sub-D
15pins
Male
M1
CONNECTION CABLE
Pair colours
Pair number
Blue
1
Withe
Orange
2
Withe
Green
3
Withe
Brown
4
Withe
Grey
5
Withe
Blue
6
Red
Orange
7
Red
Green
8
Red
M2
13
25
12
24
11
23
22
10
To cut
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Annex B - Table 7 Connection Cable 3DB10091AAAA (L.= 1.6m) or 3DB10092AAAA (L.=6,4m)
ED 05
3DB 06687 DAAA
158/178
Cable 3DB10100AAAA (L.= 1m)
Sub-D
37pins
Male
M1
M1 (37pins)
1
20
2
21
4
23
5
24
18
To cut
To cut
To cut
To cut
To cut
To cut
To cut
M1 (37pins)
7
26
8
27
10
29
11
30
18
To cut
To cut
To cut
To cut
To cut
To cut
To cut
M1 (37pins)
13
32
ED 05
CONNECTION CABLE (M1-M2)
Pair colours
Pair number
Blue
1
Withe
Orange
2
Withe
Green
3
Withe
Brown
4
Withe
Grey
5
Withe
Blue
6
Red
Orange
7
Red
Green
8
Red
CONNECTION CABLE (M1-M3)
Pair colours
Pair number
Blue
1
Withe
Orange
2
Withe
Green
3
Withe
Brown
4
Withe
Grey
5
Withe
Blue
6
Red
Orange
7
Red
Green
8
Red
CONNECTION CABLE (M1-M4)
Pair colours
Pair number
Blue
1
Withe
M2
Sub-D
9pins
Female
M3
Sub-D
9pins
Female
M4
Sub-D
9pins
Female
M2 (9pins)
1
6
2
7
8
4
9
5
3
To cut
To cut
To cut
To cut
To cut
To cut
To cut
M3 (9pins)
1
6
2
7
8
4
9
5
3
To cut
To cut
To cut
To cut
To cut
To cut
To cut
M4 (9pins)
1
6
3DB 06687 DAAA
159/178
14
33
15
34
16
35
18
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Orange
Withe
Green
Withe
Brown
Withe
Grey
Withe
Blue
Red
Orange
Red
Green
Red
2
3
4
5
6
7
8
2
7
8
4
9
5
3
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Annex B - Table 8 Connection Cable 3DB10100AAAA (L.= 1m)
ED 05
3DB 06687 DAAA
160/178
Cable 3DB10101AAAA (Adapter ESC/NMS V1)
CONNECTION CABLE
ED 05
M1
M2
5
12
6
13
7
14
8
15
1
1
9
2
10
3
11
12
4
5
3DB 06687 DAAA
161/178
Cable 3CC52119AAAA (L.= 1,6) or 3CC52120AAAA (L.=6,4)
Sub-D
9pins
Male
Sub-D
15pins
Male
M3
M1
Sub-D
9pins
Male
M2
ANNEX B - Figure 2 NMS ESC CROSSED CABLE
CONNECTION CABLE (M1-M2-M3)
M1
M2 (NMS)
M3 (AUDIO)
Pair colours
(15pins)
(9pins)
(9pins)
1
8
Blue
9
4
Withe
3
1
Violet
11
6
Turquoise
2
5
Orange
10
9
Withe
4
7
Violet
12
2
Turquoise
5 to connect to shielded cable braid (GND)
Green
To cut
Withe
6
8
Violet
13
4
Turquoise
7
1
Brown
14
6
Withe
To cut
Violet
To cut
Turquoise
Pair number
1
2
3
4
5
6
7
8
Annex B - Table 9 Connection Cable 3CC52119AAAA (L.= 1,6) or 3CC52120AAAA (L.=6,4)
ED 05
3DB 06687 DAAA
162/178
Cable 3CC52121AAAA (L.= 1m)
Sub-D 9pins
Female
Sub-D 37pins
Male
M2
M1
M3
Sub-D 25pins
Female
ANNEX B - Figure 3 LUX 50 ESC-ESC / ALARMS ADAPTER
CONNECTION CABLE (M1-M2-M3)
M1 (37pins)
1
20
2
21
4
23
5
24
11 No connect
3
6
22 no connect
25 no connect
7
26
8
27
9
28
10
29
14
15
32
33
34
16
17
18
35
36
37
19
12
30
M2 (9pins)
8
4
9
5
1
6
2
7
M3 (25pins)
Pair number
1
2
3
4
11
12
13 no connect
24 no connect
7
20
8
21
9
22
10
23
1
2
14
15
16
3
4
5
17
18
19
6
3
25
6
7
8
9
10
11
12
13
14
15
16
Annex B - Table 10 Connection - Cable 3CC52121AAAA (L.= 1m
ED 05
3DB 06687 DAAA
163/178
Cable 3DB10063AAAA (L.= 1,6)
Sub-D
9pins
Male
Sub-D
15pins
Male
M3
M1
Sub-D
9pins
Male
M2
ANNEX B - Figure 4 NMS INTERFACE AWY MELODIE IDU
CONNECTION CABLE (M1-M2-M3)
M1
M2 (NMS)
M3 (AUDIO)
Pair colours
(15pins)
(9pins)
(9pins)
1
8
Blue
9
4
Withe
3
1
Violet
11
6
Turquoise
10
5
Orange
10
9
Withe
4
2
Violet
12
7
Turquoise
5 to connect to shielded cable braid (GND)
Green
To cut
Withe
6
8
Violet
13
4
Turquoise
7
1
Brown
14
6
Withe
To cut
Violet
To cut
Turquoise
Pair number
1
2
3
4
5
6
7
8
Annex B - Table 11 Connection Cable 3DB10063AAAA (L.= 1,6)
ED 05
3DB 06687 DAAA
164/178
Cable 3DB10093AAAA (L.= 1.6m)
Sub-D
9pins
Male
Sub-D
15pins
Male
M2
M1
M1
7
14
8
15
5
12
6
13
1
To cut
To cut
To cut
To cut
To cut
To cut
To cut
CONNECTION CABLE
Pair colours
Pair number
Blue
1
Withe
Orange
2
Withe
Green
3
Withe
Brown
4
Withe
Grey
5
Withe
Blue
6
Red
Orange
7
Red
Green
8
Red
M2
6
1
7
2
4
8
5
9
3
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Annex B - Table 12 Connection Cable 3DB10093AAAA (L.= 1.6m)
ED 05
3DB 06687 DAAA
165/178
A.1.
Cable 3CC52130AAAA (L.= 1.6m) or 3CC52131AAAA (L.= 6.4m)
Sub-D
9pins
Male
Sub-D
15pins
Male
M2
M1
M1
7
14
8
15
5
12
6
13
1
To cut
To cut
To cut
To cut
To cut
To cut
To cut
CONNECTION CABLE
Pair colours
Pair number
Blue
1
Withe
Orange
2
Withe
Green
3
Withe
Brown
4
Withe
Grey
5
Withe
Blue
6
Red
Orange
7
Red
Green
8
Red
M2
1
6
2
7
8
4
9
5
3
To cut
To cut
To cut
To cut
To cut
To cut
To cut
Annex B - Table 13 Connection Cable 3DB52130AAAA (L.= 1.6m)
ED 05
3DB 06687 DAAA
166/178
Annex B
NETWORK INTERCONNECTIONS
AWY-AWY Interconnections Cable list
B.1.1.
NMS Continuity
Code
3DB05922AA**
Type Cable
Sub.D 15 pins
3DB05923AA**
Sub.D 15 pins
3DB05922AA**
Sub.D 15 pins
3DB05923AA**
Sub.D 15 pins
3DB05021AAAA
3DB14051AAAA
3DB10101AAAA
3DB10095AAAA
RJ45 8 pins
RJ45 8 pins
Sub.D 15 pins
Sub.D 15 pins
3DB10096AAAA
Sub.D 15 pins
From Equipment
To Equipment
(IDU) NMS_V11
Audio1
(IDU) NMS_V11
Audio1
(IDU) NMS_G703
Audio2
(IDU) NMS_G703
Audio2
(IDU) NMS Ethernet
(IDU) NMS Ethernet
Adapter
(IDU) NMS_V11
Audio1
(IDU) NMS_V11
Audio1
(IDU) NMS_V11 Audio1
(IDU) NMS_V11 Audio1
(IDU) NMS_G703 Audio2
(IDU) NMS_G703 Audio2
IP DCN
IP DCN
Adapter
IP Router (IP DCN)
IP Router (IP DCN)
Management
through
microwave link
Management
through
microwave link
ODU
ODU
ODU
ODU
Station A
IDU
ON
OFF
I/
O
I/
O
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC
EXT
ALC T EL
URG
ATT IDU
NURG
ODU
IDU
OD
U
ON
OFF
I/
O
I/
O
EX
T
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
ON
OFF
I/
O
I/
O
OD
U
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
GNE
OD
U
EX
T
NMS Eth
EX
T
NMS_V11 Audio1 NMS_G703 Audio2
Management
through
microwave link
AL C TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
3DB05922AA**
or
3DB05923AA**
ODU
3DB05021AAAA
or
3DB14051AAAA
IDU
IDU
RS AC
T O
ON
OFF
I/
O
I/
O
3DB05922AA**
or
3DB05923AA**
ODU
ON
OFF
OD
U
EX
T
NMS_V11 Audio1
Station C
I/
O
I/
O
ESC
EXT
A LC TEL
URG
ATT IDU
NURG
ODU
IDU
IDU
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
4W
2
EX
T
EX
T
NM
S1
NM
S2
DEB
UG
A LC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
OD
U
EX
T
NMS_G703 Audio2
Station D
IP DCN
Station B
Annex C - Figure 1 NMS Continuty
Management
through
microwave link
Management
through
microwave link
ODU
ODU
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
Station C
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
GNE
OSPF Area n
IDU
IDU
OD
U
Station A
ODU
ODU
IDU
I/
O
I/
O
OSPF Area n
I/
O
I/
O
ON
/OFF
RS AC
T O
NMS_V11 Audio 1
NMS_V11 Audio 1 NMS_V11 Audio 1
RS485 / V11
64kbps
3DB05922AA**
or
3DB05923AA**
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
3DB10095AAAA
or
3DB10096AAAA
Cisco cable X21-FC
Station B
OD
U
IP ROUTER
64kbps
IP ROUTER
IP DCN
Annex C - Figure 2 NMS Continuity
ED 05
3DB 06687 DAAA
167/178
Management
through
microwave link
ODU
ODU
IDU
I/
O
I/
O
ESC
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
NMS_V11
3DB10101AAAA
+
3DB05922AA**
ESC
EXT
EX
T
IDU
I/
O
I/
O
OD
U
ESC
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
3DB10101AAAA
+
3DB05922AA**
OD
U
GNE
EX
T
NMS_V11
NMS Eth
3DB05021AAAA
or
3DB14051AAAA
OD
U
IP DCN
Annex C - Figure 3 - NMS Continuity on ESC
ED 05
3DB 06687 DAAA
168/178
AUDIO Connection
Code
3DB05922AA**
3DB05923AA**
3DB05922AA**
3DB05923AA**
Type Cable
Sub.D 15 pins
Sub.D 15 pins
Sub.D 15 pins
Sub.D 15 pins
ODU
From Equipment
To Equipment
(IDU) NMS_G703 Audio2
(IDU) NMS_G703 Audio2
(IDU) NMS_V11 Audio1
(IDU) NMS_V11 Audio1
ODU
(IDU) NMS_G703 Audio2
(IDU) NMS_G703 Audio2
(IDU) NMS_V11 Audio1
(IDU) NMS_V11 Audio1
ODU
ODU
Station A
IDU
ON
OFF
I/
O
I/
O
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
IDU
OD
U
ON
OFF
I/
O
I/
O
EX
T
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
NMS_G703
Audio2
Station C
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC TEL
URG
ATT IDU
NURG
ODU
I/
O
I/
O
ESC
EXT
EX
T
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
NMS_G703
Audio2
ODU
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
NMS_V11 Audio1
3DB05922AA**
or
3DB05923AA**
IDU
IDU
ON
OFF
OD
U
EX
T
3DB05922AA**
or
3DB05923AA**
ODU
I/
O
I/
O
IDU
ESC
EXT
ALC T EL
URG
ATT IDU
NURG
ODU
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
NMS_V11 Audio1
Station D
Station B
Annex C - Figure 4 AUDIO Connection
ED 05
3DB 06687 DAAA
169/178
NMS Ring Protection with Audio Continuity
Code
Type Cable
3DB05922AA**
Sub.D 15 pins
3DB05923AA**
Sub.D 15 pins
3DB05922AA**
Sub.D 15 pins
3DB05923AA**
Sub.D 15 pins
3DB05021AAAA
RJ45 8 pins
3DB14051AAAA
RJ45 8 pins
ODU
From Equipment
To Equipment
(IDU) NMS_V11 Audio1
(IDU) NMS_V11 Audio1
(IDU) NMS_G703 Audio2
(IDU) NMS_G703 Audio2
(IDU) NMS Ethernet
(IDU) NMS Ethernet
(IDU) NMS_V11 Audio1
(IDU) NMS_V11 Audio1
(IDU) NMS_G703 Audio2
(IDU) NMS_G703 Audio2
(IDU) NMS Ethernet
(IDU) NMS Ethernet
ODU
ODU
ODU
Station A
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC
EXT
ALC TEL
URG
ATT IDU
NURG
ODU
IDU
OD
U
I/
O
I/
O
EX
T
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
IDU
ESC
EXT
OD
U
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
AL C T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
NMS _G703
Audio2
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
NMS _V11
Audio1
ODU
IDU
IDU
RS AC
T O
RS AC
T O
4W
1
3DB05922AA**
or
3DB05923AA**
ODU
ON
OFF
ON
OFF
3DB05922AA**
or
3DB05923AA**
3DB05021AAAA
or
3DB14051AAAA
Ethernet
I/
O
I/
O
I/
O
I/
O
EX
T
NMS _G703
Audio2
Station C
IDU
ESC
EXT
EX
T
Station D
OD
U
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
4W
2
EX
T
NM
S1
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
NMS _V11
Audio1
Station B
Annex C - Figure 5 NMS Ring protection with audio continuity
ED 05
3DB 06687 DAAA
170/178
ESC Continuity
Code
3DB10087AAAA
3DB10088AAAA
Type Cable
Sub.D 15 pins
Sub.D 15 pins
ODU
From Equipment
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC T EL
URG
ATT IDU
NURG
ODU
(IDU) ESC
(IDU) ESC
ODU
IDU
I/
O
I/
O
To Equipment
(IDU) ESC
(IDU) ESC
ESC
EXT
EX
T
OD
U
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
ESC
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ODU
ODU
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
IDU
IDU
OD
U
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
ESC
3DB10087AAAA or 3DB10088AAAA
Annex C - Figure 6 ESC Continuity
ED 05
3DB 06687 DAAA
171/178
B.2.
AWY-MELODIE SNMP Interconnections Cable list
NMS Continuity with Audio Connection
Code
Type Cable
3DB05922AA**
Sub D 15
3DB05923AA**
Sub D 15
3DB10063AAAA
Y cable sub D 15 (2x Sub D 9)
3DB10064AAAA
Y cable sub D 15 (2x Sub D 9)
3DB05021AAAA
3DB14051AAAA
RJ45 8 pins
RJ45 8 pins
From Equipment
(IDU) NMS_G703
Audio2
(IDU) NMS_G703
Audio2
AWY (IDU) NMS_V11
Audio1
AWY (IDU) NMS_V11
Audio1
(IDU) NMS Ethernet
(IDU) NMS Ethernet
To Equipment
(IDU) NMS_G703
Audio2
(IDU) NMS_G703
Audio2
Melodie (IDU)
NMS_V11 and Audio1
Melodie (IDU)
NMS_V11 and Audio1
IP DCN
IP DCN
Management
through
microwave link
Management
through
microwave link
ODU
ODU
ODU
ODU
Station A
IDU
ON
OFF
I/
O
I/
O
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
IDU
OD
U
ON
OFF
I/
O
I/
O
EX
T
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC
EXT
ALC TEL
URG
ATT IDU
NURG
ODU
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
Station D
OD
U
RS AC
T O
ODU
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
GNE
EX
T
NMS Eth
EX
T
NMS_V11
Audio1
3DB10063AA**
or
3DB10064AA**
3DB05021AAAA
or
3DB14051AAAA
IDU
IDU
RS AC
T O
ON
OFF
3DB05922AA**
or
3DB05923AA**
Management
through
microwave link
ODU
ON
OFF
I/
O
I/
O
NMS_G703
Audio2
Melodie
I/
O
I/
O
OD
U
EX
T
NMS_G703
Audio2
Station C
IDU
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
4W
2
EX
T
NM
S1
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
Audio1
EX
T
OD
U
NMS1
Station B
IP DCN
Annex C - Figure 7 NMS continuity with Audio connection
ED 05
3DB 06687 DAAA
172/178
Service Channel Continuity (MELODIE 1+0 classic)
Code
Type Cable
3DB10089AAAA Sub D 15 Sub D 9
3DB10090AAAA Sub D 15 Sub D 9
3DB10100AAAA Adapter Sub D 37 (3x Sub D 9)
From Equipment
(IDU) ESC
(IDU) ESC
To Equipment
(IDU) ESC3-4
(IDU) ESC3-4
Melodie 1+0 Classic
ODU
ODU
IDU
ON
OFF
I/
O
I/
O
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
IDU
OD
U
I/
O
I/
O
EX
T
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ON
OFF
RS AC
T O
ODU
ODU
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
IDU
IDU
OD
U
ON
OFF
I/
O
I/
O
EX
T
RS AC
T O
ESC
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC 3-4
3DB10089AAAA
or
3DB10090AAAA
ESC
EXT
ON
OFF
I/
O
I/
O
OD
U
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
3DB10100AAAA
Annex C - Figure 8 Service Channel continuity (MELODIE 1+0 classic)
Service Channel Continuity (MELODIE 1+0 Light)
Code
Type Cable
3CC52130AAAA
3CC52131AAAA
3DB10121AAAA
Sub D 15-Sub D 9
Sub D 15-Sub D 9
Y cable sub D 37 (Sub D 9 + Sub D 25)
From
Equipment
AWY (IDU) ESC
AWY (IDU) ESC
Melodie
ESC3/Alarm
To Equipment
Y cable Sub D 9 ESC3
Y cable Sub D 9 ESC3
Melodie 1+0 Light
ODU
ODU
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
OD
U
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ODU
ODU
A LC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
IDU
IDU
OD
U
EX
T
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
AL C TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
ESC 3
ESC
3CC52130AAAA
or
3CC52131AAAA
Alarm
3CC52121AAAA
Annex C - Figure 9 Service Channel continuity (MELODIE 1+0 Light)
ED 05
3DB 06687 DAAA
173/178
Service Channel Continuity (MELODIE 1+1)
Code
Type Cable
From Equipment
3DB10091AAAA Sub D 15 Sub D 9
(IDU) ESC
3DB10092AAAA Sub D 15 Sub D 9
(IDU) ESC
To Equipment
(IDU) ESC5
(IDU) ESC5
Melodie 1+1
ODU
ODU
ODU
ODU
Main IDU
Main IDU
IDU
IDU
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ON
OFF
I/
O
I/
O
RS AC
T O
ESC EXT
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
I/
O
I/
O
EX
T
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC
EXT
ALC T EL
URG
ATT IDU
NURG
ODU
OD
U
EX
T
ESC
I/
O
I/
O
RS AC
T O
4W
1
ESC
EXT
NM
S1
I/
O
I/
O
EX
T
4W
2
EX
T
NM
S2
DEB
UG
URG
ATT IDU
NURG
ODU
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC EXT
ESC
EXT
ALC T EL
ON
OFF
OD
Ext. IDU
ESC MAIN
ON
OFF
ESC
EXT
ALC T EL
URG
ATT IDU
NURG
ODU
OD
U
I/
O
I/
O
EX
T
RS AC
T O
OD
U
EX
T
Ext. IDU
ESC MAIN
ON
OFF
ESC
EXT
A LC T EL
URG
ATT IDU
NURG
ODU
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC
EXT
ALC T EL
URG
ATT IDU
NURG
ODU
OD
U
EX
T
ESC 5
3DB10091AAAA or 3DB10092AAAA
Annex C - Figure 10 Service Channel continuity (MELODIE 1+1)
Service Channel Continuity (MELODIE 1+1)
Code
Type Cable
From Equipment
3DB10089AAAA Sub D 15 Sub D 9 (IDU) ESC
3DB10090AAAA Sub D 15 Sub D 9 (IDU) ESC
To Equipment
(IDU) ESC3-4
(IDU) ESC3-4
Melodie 1+1
ODU
ODU
ODU
ODU
Main IDU
Main IDU
IDU
IDU
ON
OFF
I/
O
I/
O
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
OD
U
I/
O
I/
O
ON
OFF
RS AC
T O
ESC
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
OD
U
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC EXT
ALC T EL
URG
ATT IDU
NURG
ODU
ON
OFF
RS AC
T O
4W
1
4W
2
ESC
EXT
NM
S1
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ON
OFF
OD
I/
O
I/
O
EX
T
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC EXT
Ext. IDU
ESC MAIN
I/
O
I/
O
ESC
EXT
ESC
EXT
EX
T
OD
U
ALC T EL
URG
ATT IDU
NURG
ODU
ON
OFF
RS AC
T O
OD
U
EX
T
Ext. IDU
ESC MAIN
I/
O
I/
O
ESC
EXT
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
ESC 3-4
3DB10089AAAA or 3DB10090AAAA
Annex C - Figure 11 - Service Channel continuity (MELODIE 1+1)
ED 05
3DB 06687 DAAA
174/178
AWY-MELODIE RQ2 Interconnections Cable list
AWY NMS_V11 Transport (MELODIE 1+0 Classic)
Code
Type Cable
3DB10063AAAA Y cable sub D 15 (2x Sub D 9)
3DB10064AAAA Y cable sub D 15 (2x Sub D 9)
3DB10100AAAA Adapter Sub D 37 (3x Sub D 9)
From Equipment
(IDU) NMS_V11 Audio 1
(IDU) NMS_V11 Audio 1
To Equipment
(IDU) ESC3-4-5
(IDU) ESC3-4-5
Melodie 1+0 Classic
ODU
ODU
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ODU
ODU
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
IDU
IDU
OD
U
I/
O
I/
O
EX
T
ON
OFF
RS AC
T O
NMS_V11 Audio1
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
ON
OFF
I/
O
I/
O
OD
U
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
ESC 3
3DB10063AAAA
or
3DB10064AAAA
ESC 4
3DB10100AAAA
ESC 5
Annex C - Figure 12 AWY NMS V11 Transport (MELODIE 1+0 classic)
AWY NMS_V11 Transport (MELODIE 1+0 Light)
Code
Type Cable
3CC52119AAAA Y cable sub D 15 (2x Sub D 9)
From Equipment
(IDU) NMS_V11 Audio
1
(IDU) NMS_V11 Audio
1
3CC52120AAAA
Y cable sub D 15 (2x Sub D 9)
3CC52121AAAA
Y cable sub D 37 (Sub D 9 + Sub D 25)
To Equipment
(IDU) ESC5
(IDU) ESC5
Melodie 1+0 Light
ODU
ODU
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
IDU
IDU
IDU
I/
O
I/
O
ODU
ODU
OD
U
EX
T
NMS_V11 Audio1
3CC52119AAAA
or
3CC52120AAAA
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
ESC 3
3CC52121AAAA
Annex C - Figure 13 - AWY NMS V11 Transport (MELODIE 1+0 light)
ED 05
3DB 06687 DAAA
175/178
AWY NMS_V11 Transport (MELODIE 1+1)
Code
Type Cable
3DB10063AAAA Y cable sub D 15 (2x Sub D 9)
3DB10064AAAA Y cable sub D 15 (2x Sub D 9)
From Equipment
(IDU) NMS_V11 Audio 1
(IDU) NMS_V11 Audio 1
To Equipment
(IDU) ESC3-4
(IDU) ESC3-4
Melodie 1+1
ODU
ODU
ODU
ODU
Main IDU
Main IDU
IDU
IDU
ON
OFF
I/
O
I/
O
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
I/
O
I/
O
EX
T
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC EXT
OD
U
EX
T
NMS_V11 Audio1
I/
O
I/
O
RS AC
T O
4W
1
ESC
EXT
NM
S1
I/
O
I/
O
EX
T
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ON
OFF
OD
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC EXT
Ext. IDU
ESC MAIN
ON
OFF
ESC
EXT
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
ESC MAIN
OD
U
I/
O
I/
O
EX
T
ON
OFF
RS AC
T O
ESC
EXT
ALC T EL
URG
ATT IDU
NURG
ODU
OD
U
EX
T
Ext. IDU
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
ESC 3-4
3DB10063AAAA or 3DB10064AAAA
Annex C - Figure 14 - AWY NMS V11 Transport (MELODIE 1+1)
AWY NMS_V11 Transport (MELODIE 1+1)
Code
Type Cable
3DB10063AAAA Y cable sub D 15 (2x Sub D 9)
3DB10064AAAA Y cable sub D 15 (2x Sub D 9)
3CC52132AAAA Sub D 25 Sub D 9
From Equipment
(IDU) NMS_V11 Audio 1
(IDU) NMS_V11 Audio 1
(IDU) NMS_V11 Audio 1
To Equipment
(IDU) ESC5
(IDU) ESC5
Melodie 1+1
ODU
ODU
ODU
ODU
Main IDU
Main IDU
IDU
IDU
ON
OFF
I/
O
I/
O
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
OD
U
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
NMS_V11 Audio1
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC EXT
ALC T EL
URG
ATT IDU
NURG
ODU
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
I/
O
I/
O
EX
T
ESC
EXT
ON
OFF
OD
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ESC EXT
Ext. IDU
ESC MAIN
I/
O
I/
O
ESC
EXT
OD
U
EX
T
ALC T EL
URG
ATT IDU
NURG
ODU
ESC MAIN
I/
O
I/
O
ON
OFF
RS AC
T O
ESC
EXT
OD
U
EX
T
Ext. IDU
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ALC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
ESC 5
3DB10063AAAA or 3DB10064AAAA
3CC52132AAAA
Annex C - Figure 15 - AWY NMS V11 Transport (MELODIE 1+1)
ED 05
3DB 06687 DAAA
176/178
RQ2 9.6 K/b Transport
Code
Type Cable
3DB10093AAAA Sub D 15 Sub D 9
3DB10094AAAA Sub D 15 Sub D 9
From Equipment
To Equipment
(IDU) ESC
(IDU) ESC
(IDU) NMS1
(IDU) NMS1
Melodie
ODU
ODU
IDU
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
OD
U
IDU
I/
O
I/
O
ESC
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
ODU
ODU
A LC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
EX
T
IDU
IDU
OD
U
I/
O
I/
O
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC TEL
URG
ATT IDU
NURG
ODU
ESC
EXT
I/
O
I/
O
OD
U
ON
OFF
RS AC
T O
4W
1
ESC
EXT
NM
S1
4W
2
EX
T
NM
S2
DEB
UG
A LC T EL
URG
ATT IDU
NURG
ODU
ESC
EXT
OD
U
EX
T
EX
T
NMS1
3DB10093AAAA or 3DB10094AAAA
Annex C - Figure 16 RQ2 9.6 K/b Transport
ED 05
3DB 06687 DAAA
177/178
END OF DOCUMENT
ED 05
3DB 06687 DAAA
178/178
All rights reserved. Passing on and copying of this
document, use and communication of its contents
not permitted without written authorization from Alcatel.
QUESTA PAGINA NON VA INSERITA NEL MANUALE
THIS PAGE MUST NOT BE INCLUDED IN THE HANDBOOK
COD.MANUALE HDBK P/N:
3DB 06687 DAAA Ed.05
9400AWY Rel.2.0
INSTALLATION HANDBOOK
ISTRUZIONI PER LA STAMPA ED ASSIEMAGGIO DI QUESTO MANUALE
INSTRUCTIONS FOR PRINT AND ASSEMBLY OF THIS MANUAL
COMPOSIZIONE ED ASSIEMAGGIO DEL MANUALE:
HANDBOOK COMPOSITION AND ASSEMBLY:
STAMPARE FRONTE/RETRO RECTO-VERSO PRINTING
numerate
numbered
No pagine
(facciate)
No pages
da from
a to
INSTALLATION HANDBOOK
178
1/178
178/178
TOTALE PAGINE A4 (FACCIATE) TOTAL A4 PAGES:
178
TOTALE FOGLI A4 TOTAL A4 SHEETS:
89
fase
step
TARGHETTE - LABELS
N.B. se il manuale viene termorilegato senza
cartelletta, le targhette non servono. Come
copertina, utilizzare il frontespizio del manuale
(pagina 1), stampato su cartoncino.
N.B. if handbook is thermobound without binder,
labels are not necessary. As bookcover, use the
manual front (page 1).
3DB 06687 DAAA TQZZA Ed.05
1/4
THIS PAGE MUST NOT BE INCLUDED IN THE HANDBOOK
PUBLISHING NOTES
Labels are done according to A-Italy binder format.
Source files and printable files of this handbook are archived in PDM:
Source file:
SOURCE FORMAT
SIZE Kbytes
PDM ARCHIVE
METHOD
TOTAL N.PAGES
MSWORD2000
135.037
WINZIP
178+ 4 = 182
N.B.
the cat_IDU file contains the source interleaf file for this assembly document (it
can be opened by Quicksilver 1.5.3 in PCWINDOWS environment or by
Interleaf 6 in Unix environment).
Printable file: PDF file must be opened with ACROBAT Reader Version 5.0 at least.
(N.B. : it has been created with ACROBAT DISTILLER 7.0)
3DB 06687 DAAA
TQZZA
Ed.05
9400AWY Rel.2.0
7813151823252838 GHz
shorthaul low/medium capacity digital microwave radio links
INSTALLATION HANDBOOK
2/4
3DB 06687 DAAA TQZZA Ed.05
All rights reserved. Passing on and copying of this
document, use and communication of its contents
not permitted without written authorization from Alcatel.
QUESTA PAGINA NON VA INSERITA NEL MANUALE
All rights reserved. Passing on and copying of this
document, use and communication of its contents
not permitted without written authorization from Alcatel.
9400AWY Rel.2.0
7813151823252838 GHz
shorthaul low/medium capacity digital microwave radio links
INSTALLATION HANDBOOK
3DB 06687 DAAA Ed.05
VOL.1/1
9400AWY Rel.2.0
7813151823252838 GHz
shorthaul low/medium capacity digital microwave radio links
INSTALLATION HANDBOOK
3DB 06687 DAAA Ed.05
VOL.1/1
9400AWY Rel.2.0
7813151823252838 GHz
shorthaul low/medium capacity digital microwave radio links
3DB 06687 DAAA Ed.05
INSTALLATION HANDBOOK
VOL.1/1
9400AWY Rel.2.0
7813151823252838 GHz shorthaul low/medium capacity digital microwave radio links
3DB 06687 DAAA Ed.05
INSTALLATION HANDBOOK
VOL.1/1
9400AWY Rel.2.0
7813151823252838 GHz
shorthaul low/medium capacity digital microwave radio links
3DB 06687 DAAA Ed.05
INSTALLATION HANDBOOK
3DB 06687 DAAA TQZZA Ed.05
VOL.1/1
3/4
END OF DOCUMENT FINE DEL DOCUMENTO INTERNO
4/4
3DB 06687 DAAA TQZZA Ed.05
All rights reserved. Passing on and copying of this
document, use and communication of its contents
not permitted without written authorization from Alcatel.
You might also like
- CAN and FPGA Communication Engineering: Implementation of a CAN Bus based Measurement System on an FPGA Development KitFrom EverandCAN and FPGA Communication Engineering: Implementation of a CAN Bus based Measurement System on an FPGA Development KitNo ratings yet
- Normarc 7000 ILS Installation and Commissioning Handbook Vol2 91128 PDF50% (2)Normarc 7000 ILS Installation and Commissioning Handbook Vol2 91128 PDF84 pages
- TCM4171334781635 - V1 - 9400awy R2.10 InstallationNo ratings yetTCM4171334781635 - V1 - 9400awy R2.10 Installation180 pages
- 3db05653daaatqzza v1 9400awy 10 Zinstallation.pdf (1)No ratings yet3db05653daaatqzza v1 9400awy 10 Zinstallation.pdf (1)105 pages
- SJ-20151105160120-004-ZXMW NR8250 (V2.04.02) Hardware Installation GuideNo ratings yetSJ-20151105160120-004-ZXMW NR8250 (V2.04.02) Hardware Installation Guide186 pages
- Prediction of Burnout: An Artificial Neural Network ApproachFrom EverandPrediction of Burnout: An Artificial Neural Network ApproachNo ratings yet
- CNC Machining Handbook: Building, Programming, and ImplementationFrom EverandCNC Machining Handbook: Building, Programming, and ImplementationNo ratings yet
- Making Everyday Electronics Work: A Do-It-Yourself Guide: A Do-It-Yourself GuideFrom EverandMaking Everyday Electronics Work: A Do-It-Yourself Guide: A Do-It-Yourself Guide4/5 (2)
- OptiX RTN310&900 Installation Standard - Indosat Jaguar Project - Rev 1.1No ratings yetOptiX RTN310&900 Installation Standard - Indosat Jaguar Project - Rev 1.163 pages
- DC/DC Converter Handbook: SMPS topologies from an EMC point of viewFrom EverandDC/DC Converter Handbook: SMPS topologies from an EMC point of viewNo ratings yet
- Pasolink V4 Installation and Initial Lineup Description100% (2)Pasolink V4 Installation and Initial Lineup Description70 pages
- NEC Pasolink NEO Series: Installation: Typical Installation FlowNo ratings yetNEC Pasolink NEO Series: Installation: Typical Installation Flow33 pages
- Programming Arduino Next Steps: Going Further with Sketches, Second EditionFrom EverandProgramming Arduino Next Steps: Going Further with Sketches, Second Edition3/5 (3)
- Marine VHF Radiotelephone (JHS-770S) Two-Way VHF Radiotelephone (Jhs-7) Uhf Antenna System (Nau-6) (Incl. Inst. Manual & Test Report)No ratings yetMarine VHF Radiotelephone (JHS-770S) Two-Way VHF Radiotelephone (Jhs-7) Uhf Antenna System (Nau-6) (Incl. Inst. Manual & Test Report)243 pages
- Electronics from the Ground Up: Learn by Hacking, Designing, and InventingFrom EverandElectronics from the Ground Up: Learn by Hacking, Designing, and Inventing3.5/5 (2)
- Microwave Hardware Quality Report: Rtn620 - InstallationNo ratings yetMicrowave Hardware Quality Report: Rtn620 - Installation3 pages
- Nuclear Commerce: Its Control Regime and the Non-Proliferation TreatyFrom EverandNuclear Commerce: Its Control Regime and the Non-Proliferation TreatyNo ratings yet
- ZXRAN A9631W S36 5G Active Antenna Unit Hardware InstallationNo ratings yetZXRAN A9631W S36 5G Active Antenna Unit Hardware Installation95 pages
- ZTE Manual de Instalación de Hardware ER2020E100% (1)ZTE Manual de Instalación de Hardware ER2020E78 pages
- Trango Antenna User Manual ADXX XX SX 1 and 2 FT DiamNo ratings yetTrango Antenna User Manual ADXX XX SX 1 and 2 FT Diam14 pages
- Installation and Operation Manual For Sea Tel Model: 9697 C-Band Unlimited Azimuth Transmit / Receive SystemNo ratings yetInstallation and Operation Manual For Sea Tel Model: 9697 C-Band Unlimited Azimuth Transmit / Receive System116 pages
- SJ-20130930111159-004-ZXMW NR8250 (V2.03.02) Hardware Installation GuideNo ratings yetSJ-20130930111159-004-ZXMW NR8250 (V2.03.02) Hardware Installation Guide144 pages
- Konnect Vhts EU Installation Guide VdraftNo ratings yetKonnect Vhts EU Installation Guide Vdraft20 pages
- Advanced Synthesis of Gold and Zirconia Nanoparticles and their CharacterizationFrom EverandAdvanced Synthesis of Gold and Zirconia Nanoparticles and their CharacterizationNo ratings yet
- Brochure Outdoor Vacuum Circuit Breaker UsNo ratings yetBrochure Outdoor Vacuum Circuit Breaker Us12 pages
- Ceramic Resonators (Ceralockr) : Lead Type Three Terminals Cstls SeriesNo ratings yetCeramic Resonators (Ceralockr) : Lead Type Three Terminals Cstls Series2 pages
- Presentation of Industrial Training in JPLNo ratings yetPresentation of Industrial Training in JPL24 pages
- Darlington: Silicon PNP Epitaxial Planar Transistor (Complement To Type 2SD2561)No ratings yetDarlington: Silicon PNP Epitaxial Planar Transistor (Complement To Type 2SD2561)1 page
- Herion N - 201 Valvulas SOFT SEAL 3V2P 5V2PNo ratings yetHerion N - 201 Valvulas SOFT SEAL 3V2P 5V2P4 pages
- Panasonic kx-mb2000 2010hxb (ET) Printservis - Com.ua PDFNo ratings yetPanasonic kx-mb2000 2010hxb (ET) Printservis - Com.ua PDF267 pages
- TP48200A Product Description (V100R001 - 01)50% (2)TP48200A Product Description (V100R001 - 01)42 pages
- Agricultural Power, Machinery and Mechanization and Allied SubjectsNo ratings yetAgricultural Power, Machinery and Mechanization and Allied Subjects24 pages
- 80C51 Core Architecture 256 Bytes of On-Chip RAM 2048 BytesNo ratings yet80C51 Core Architecture 256 Bytes of On-Chip RAM 2048 Bytes197 pages
- Quotation: Daikin System 2 I-Smile Series - R410 Gas (5 Ticks) Built-In WifiNo ratings yetQuotation: Daikin System 2 I-Smile Series - R410 Gas (5 Ticks) Built-In Wifi2 pages
- Main Components of The Digital Logic LayerNo ratings yetMain Components of The Digital Logic Layer1 page
- Frost Free Refrigerator User Manual ................................... .....................................No ratings yetFrost Free Refrigerator User Manual ................................... .....................................33 pages
