_____________________________________________________________2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY

ANANTAPUR ANANTHAPURAMU-515002 (A.P) INDIA

ACADEMIC REGULATIONS COURSE STRUCTURE

AND
DETAILED SYLLABI
OF
MASTER OF TECHNOLOGY
IN
PRODUCTION ENGINEERING AND ENGINEERIN DESIGN

Regular Two Year P.G. Degree Course

(Applicable for the batches admitted from 2013-14)

2013-14_____________________________________________________________

Academic Regulations-M.Tech. 2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

Academic Regulations For The Award Of Full Time M.Tech. P.G. Degree
(WITH EFFECT FROM THE ACADEMIC YEAR 2013-14)
The Jawaharlal Nehru Technological University Anantapur shall confer M.Tech. Post
Graduate degree to candidates who are admitted to the Master of Technology Programs and fulfill
all the requirements for the award of the degree.
1.0

ELIGIBILITY FOR ADMISSIONS:

Admission to the above programme shall be made subject to the eligibility, qualifications
and specialization prescribed by the University for each programme, from time to time.
Admissions shall be made either on the basis of merit rank obtained by the qualified
candidates at an Entrance Test conducted by the University or on the basis of GATE /
PGECET score, subject to reservations prescribed by the University or Government policies
from time to time.
2.0
COURSE WORK:
2.1
2.2
2.3

3.0

A Candidate after securing admission must pursue the M.Tech. course of study for Four
semesters duration.
Each semester shall be of 20 weeks duration including all examinations.
A candidate admitted to a programme should complete it within a period equal to twice
the prescribed duration of the programme from the date of admission.

ATTENDANCE:
3.1 A candidate shall be deemed to have eligibility to write end semester examinations if he
has put in atleast 75% of attendance on cumulative basis of all subjects/courses in the
semester.
3.2 Condonation of shortage of attendance up to 10% i.e., from 65% and above and less
than 75% may be given by the college on the recommendation of the Principal.
3.3 Condonation of shortage of attendance shall be granted only on genuine and valid
reasons on representation by the candidate with supporting evidence.
3.4 If the candidate does not satisfy the attendance requirement he is detained for want of
attendance and shall reregister for that semester. He / she shall not be promoted to the
next semester.

_____________________________________________________________2013-14

4.0. EVALUATION:
The performance of the candidate in each semester shall be evaluated subject wise, with a
maximum of 100 marks for Theory and 100 marks for practicals, on the basis of Internal
Evaluation and End Semester Examination.
4.1 For the theory subjects 60% of the marks will be for the External End Examination.
While 40% of the marks will be for Internal Evaluation, based on the better of the
marks secured in the two Mid Term-Examinations held, one in the middle of the
Semester (I-IV units) and another immediately after the completion of instruction
(V-VIII) units with Three questions to be answered out of four in 2hours, evaluated* for
40 marks.
*Note: All the Questions shall be of equal weightage of 10 marks and the marks
obtained for 3questions shall be extrapolated to 40 marks, any fraction rounded off to
the next higher mark
4.2 For practical subjects, 60 marks shall be for the End Semester Examinations and 40
marks will be for internal evaluation based on the day to day performance.
4.3 For Seminar there will be an internal evaluation of 50 marks. A candidate has to secure
a minimum of 50% to be declared successful. The assessment will be made by a board
consisting of HOD and two internal experts at the end of IV semester instruction.
4.4 A candidate shall be deemed to have secured the minimum academic requirement in a
subject if he secures a minimum of 40% of marks in the End Examination and a
minimum aggregate of 50% of the total marks in the End Semester Examination and
Internal Evaluation taken together.
4.5 In case the candidate does not secure the minimum academic requirement in any of the
subjects (as specified in 4.4.) he has to reappear for the Semester Examination either
supplementary or regular in that subject, or repeat the course when next offered or do
any other specified subject as may be required.
5.0

5.1
5.2
5.3

5.4
5.5

RE-REGISTRATION FOR IMPROVEMENT OF INTERNAL EVALUATION

MARKS:
Following are the conditions to avail the benefit of improvement of internal evaluation
marks.
The candidate should have completed the course work and obtained examinations
results for I & II semesters.
He should have passed all the subjects for which the Internal evaluation marks secured
are more than 50%.
Out of the subjects the candidate has failed in the examination due to Internal evaluation
marks secured being less than 50%, the candidate shall be given one chance for each
Theory subject and for a maximum of three Theory subjects for Improvement of
Internal evaluation marks.
The candidate has to re-register for the chosen subjects and fulfill the academic
requirements.
For each subject, the candidate has to pay a fee equivalent to one third of the semester
tuition fee and the amount is to be remitted in the form of D.D. in favour of the
3

2013-14_____________________________________________________________

5.6

6.0

6.1

6.2
6.3

6.4

6.5

6.6

6.7

6.8

Registrar, JNTUA payable at Anantapur along with the requisition through the Principal
of the respective college.
In the event of availing the Improvement of Internal evaluation marks, the internal
evaluation marks as well as the End Examinations marks secured in the previous
attempt(s) for the reregistered subjects stand cancelled.
EVALUATION OF PROJECT WORK:
Every candidate shall be required to submit thesis or dissertation after taking up a topic
approved by the college/ institute.
Registration of Project work: A candidate is permitted to register for the project work
after satisfying the attendance requirement of all the courses (theory and practical
courses of I & II Sem)
An Internal Departmental Committee (I.D.C) consisting of HOD, Supervisor and one
internal senior expert shall monitor the progress of the project work.
The work on the project shall be initiated in the penultimate semester and continued in
the final semester. The duration of the project is for two semesters. The candidate can
submit Project thesis with the approval of I.D.C. after 36 weeks from the date of
registration at the earliest and one calendar year from the date of registration for the
project work. Extension of time within the total permissible limit for completing the
programme is to be obtained from the Head of the Institution.
The student must submit status report at least in three different phases during the project
work period. These reports must be approved by the I.D.C before submission of the
Project Report.
A candidate shall be allowed to submit the thesis / dissertation only after passing in all
the prescribed subjects (both theory and practical) and then take viva voce examination
of the project. The viva-voce examination may be conducted once in two months for all
the candidates submitted during that period.
Three copies of the Thesis / Dissertation certified in the prescribed from by the
supervisor & HOD shall be presented to the HOD One copy is to be forwarded to the
University and one copy to be sent to the examiner.
The college shall submit a panel of three experts for a maximum of 5 students at a time.
However, the thesis / dissertation will be adjudicated by one examiner nominated by the
University.
If the report of the examiner is favorable viva-voce examination shall be conducted by a
board consisting of the Supervisor, Head of the Department and the examiner who
adjudicated the thesis / dissertation. The board shall jointly report candidates work as:
1.
Very Good
Grade A
2.
Good
Grade B
3.
Satisfactory
Grade C
4.
Not satisfactory
Grade D
If the report of the viva-voce is not satisfactory (Grade D) the candidate will retake the
viva-voce examination after three months. If he fails to get a satisfactory report at the
second viva-voce examination he will not be eligible for the award of the degree unless
the candidate is permitted to revise and resubmit the thesis.

_____________________________________________________________2013-14

7.0

AWARD OF DEGREE AND CLASS:

A candidate shall be eligible for the award of respective degree if he satisfies the
minimum academic requirements in every subject and secures satisfactory or higher
grade report on his thesis/dissertation and viva-voce. Based on overall percentage of
marks obtained, the following class is awarded.
First class with Distinction:
70% or more
First class
below 70% but not less than 60%
Second class
below 60% but not less than 50%

8.0

WITH HOLDING OF RESULTS:

If the candidate has not paid dues to the university or if any case of in-discipline is
pending against him, the result of the candidate shall be withheld and he will not be
allowed/ promoted into the next higher semester. The issue of degree is liable to be
withheld in such cases.

9.0

TRANSITORY REGULATIONS:
Candidates who have discontinued or have been detained for want of attendance or who
have failed after having undergone the course in earlier regulations and wish to continue
the course are eligible for admission into the unfinished semester from the date
of
commencement of class work with the same or equivalent subjects as and when subjects
are offered, subject to 4.5 and 2.3 sections. Whereas they continue to be in the academic
regulations they were first admitted.
10.0
GENERAL:
i. The academic regulations should be read as a whole for purpose of any
interpretation.
ii. Disciplinary action for Malpractice / improper conduct in examinations is
appended.
iii. There shall be no places transfer within the constituent colleges and affiliated
colleges of Jawaharlal Nehru Technological University Anantapur.
iv. Where the words he, him, his, occur in the regulations, they include she,
her, hers.
v. In the case of any doubt or ambiguity in the interpretation of the above rules, the
decision of the Vice-Chancellor is final.
vi. The University may change or amend the academic regulations or syllabi at any
time and the changes or amendments shall be made applicable to all the students
on rolls with effect from the dates notified by the University.
******

2013-14_____________________________________________________________

APPROVED REVISION OF RULES FOR DISCIPLINARY ACTION FOR

MALPRACTICES / IMPROPER CONDUCT IN EXAMINATIONS
Nature of Malpractices/Improper conduct
1.
(a)

(b)

2.

3.

If the candidate:
Possesses or keeps accessible in examination
hall, any paper, note book, programmable
calculators, Cell phones, pager, palm
computers or any other form of material
concerned with or related to the subject of the
examination (theory or practical) in which he is
appearing but has not made use of (material
shall include any marks on the body of the
candidate which can be used as an aid in the
subject of the examination)
Gives assistance or guidance or receives it
from any other candidate orally or by any other
body language methods or communicates
through cell phones with any candidate or
persons in or outside the exam hall in respect
of any matter.
Has copied in the examination hall from any
paper, book, programmable calculators, palm
computers or any other form of material
relevant to the subject of the examination
(theory or practical) in which the candidate is
appearing.

Impersonates any other candidate

connection with the examination.

Punishment
Expulsion from the examination hall and
cancellation of the performance in that subject
only.

Expulsion from the examination hall and

cancellation of the performance in that subject
only of all the candidates involved. In case of an
outsider, he will be handed over to the police and
a case is registered against him.
Expulsion from the examination hall and
cancellation of the performance in that subject
and all other subjects the candidate has already
appeared including practical examinations and
project work and shall not be permitted to appear
for the remaining examinations of the subjects of
that Semester/year.
The Hall Ticket of the candidate is to be
cancelled and sent to the University.

in The candidate who has impersonated shall be

expelled from examination hall. The candidate
is also debarred for four consecutive semesters
from class work and all University
examinations. The continuation of the course
by the candidate is subject to the academic
regulations in connection with forfeiture of
seat.
The performance of the original candidate who
has been impersonated, shall be cancelled in all
the subjects of the examination (including
practicals and project work) already appeared

_____________________________________________________________2013-14

4.

Smuggles in the Answer book or additional

sheet or takes out or arranges to send out the
question paper during the examination or
answer book or additional sheet, during or after
the examination.

5.

Uses objectionable, abusive or offensive

language in the answer paper or in letters to the
examiners or writes to the examiner requesting
him to award pass marks.
Refuses to obey the orders of the Chief
Superintendent/Assistant Superintendent /
any officer on duty or misbehaves or creates
disturbance of any kind in and around the
examination hall or organizes a walk out or
instigates others to walk out, or threatens the
officer-in charge or any person on duty in or
outside the examination hall of any injury to
his person or to any of his relations whether by
words, either spoken or written or by signs or
by visible representation, assaults the officerin-charge, or any person on duty in or outside
the examination hall or any of his relations, or

6.

and shall not be allowed to appear for

examinations of the remaining subjects of that
semester/year. The candidate is also debarred
for four consecutive semesters from class work
and all University examinations, if his
involvement is established. Otherwise, The
candidate is debarred for two consecutive
semesters from class work and all University
examinations. The continuation of the course
by the candidate is subject to the academic
regulations in connection with forfeiture of
seat.
If the imposter is an outsider, he will be
handed over to the police and a case is
registered against him.
Expulsion from the examination hall and
cancellation of performance in that subject and all
the other subjects the candidate has already
appeared including practical examinations and
project work and shall not be permitted for the
remaining examinations of the subjects of that
semester/year. The candidate is also debarred for
two consecutive semesters from class work and
all University examinations. The continuation of
the course by the candidate is subject to the
academic regulations in connection with forfeiture
of seat.
Cancellation of the performance in that subject
only.

In case of students of the college, they shall be

expelled from examination halls and
cancellation of their performance in that
subject and all other subjects the candidate(s)
has (have) already appeared and shall not be
permitted to appear for the remaining
examinations of the subjects of that
semester/year. If the candidate physically
assaults the invigilator/ officer-in-charge of the
Examinations, then the candidate is also
debarred and forfeits his/her seat. In case of
outsiders, they will be handed over to the
police and a police case is registered against

2013-14_____________________________________________________________

7.

indulges in any other act of misconduct or

mischief which result in damage to or
destruction of property in the examination hall
or any part of the College campus or engages
in any other act which in the opinion of the
officer on duty amounts to use of unfair means
or misconduct or has the tendency to disrupt
the orderly conduct of the examination.
Leaves the exam hall taking away answer
script or intentionally tears of the script or any
part thereof inside or outside the examination
hall.

8.

Possess any lethal weapon or firearm in the

examination hall.

9.

If student of the college, who is not a candidate

for the particular examination or any person
not connected with the college indulges in any
malpractice or improper conduct mentioned in
clause 6 to 8.

10.

Comes in a drunken condition to the

examination hall.

them.

Expulsion from the examination hall and

cancellation of performance in that subject and all
the other subjects the candidate has already
appeared including practical examinations and
project work and shall not be permitted for the
remaining examinations of the subjects of that
semester/year. The candidate is also debarred for
two consecutive semesters from class work and
all University examinations. The continuation of
the course by the candidate is subject to the
academic regulations in connection with forfeiture
of seat.
Expulsion from the examination hall and
cancellation of the performance in that subject
and all other subjects the candidate has already
appeared including practical examinations and
project work and shall not be permitted for the
remaining examinations of the subjects of that
semester/year. The candidate is also debarred and
forfeits the seat.
Student of the colleges expulsion from the
examination hall and cancellation of the
performance in that subject and all other subjects
the candidate has already appeared including
practical examinations and project work and shall
not be permitted for the remaining examinations
of the subjects of that semester/year. The
candidate is also debarred and forfeits the
seat.Person(s) who do not belong to the College
will be handed over to police and, a police case
will be registered against them.
Expulsion from the examination hall and
cancellation of the performance in that subject
and all other subjects the candidate has already
appeared including practical examinations and
project work and shall not be permitted for the

_____________________________________________________________2013-14

11.

12.

remaining examinations of the subjects of that

semester/year.
Copying detected on the basis of internal Cancellation of the performance in that subject
evidence, such as, during valuation or during only or in that subject and all other subjects
special scrutiny.
the candidate has appeared including practical
examinations and project work of that
semester/year examinations, depending on the
recommendation of the committee.
If any malpractice is detected which is not
covered in the above clauses 1 to 11 shall be
reported to the University for further action to
award suitable punishment.

Malpractices identified by squad or special invigilators

1. Punishments to the candidates as per the above guidelines.
2. Punishment for institutions : (if the squad reports that the college is also involved in
encouraging malpractices)
(i) A show cause notice shall be issued to the college.
(ii) Impose a suitable fine on the college.
(iii) Shifting the examination centre from the college to another college for a specific
period of not less than one year.

Note: Whenever the performance of a student is cancelled in any subject/subjects

due to Malpractice, he has to register for End Examinations in that subject/subjects
consequently and has to fulfill all the norms required for the award of Degree.

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

Course Structure and syllabi for
M.Tech- Production Engineering and Engineering Design
Offered by Department of Mechanical Engineering
for affiliated Engineering Colleges 2013-14
I YEAR I Semester
S.
No
1.
2.
3.
4.
5.

6.

Course
code
9D04102
9DBS101
9D04105
9D15203
9D04201

Subject

Theory Lab. Credits

Finite Element Methods

Computational methods
Advances in Manufacturing Technology
Mechanical Vibrations
Advanced Optimization Techniques
Elective-I
9D04108 a. Design for Manufacturing
9D04206 b. Rapid Prototyping
12D87207 c. Design and manufacturing of MEMS and
MICRO systems
13D90101 Design Simulation Laboratory
Total Credits

10

4
4
4
4
4
4

4
4
4
4
4
4

2
26

_____________________________________________________________2013-14

I YEAR II Semester
S.
No
1.
2.
3.
4.

Course
code
12D87208
12D87101
12D87203
9D15102
9D04208

5.

6.

9D04203
13D90201
9D15108
12D87209

II YEAR

Subject

Theory Lab. Credit

s
Industrial Robotics
4
4
Automation in Manufacturing
4
4
Simulation & Modeling of Manufacturing systems 4
4
4
4
Advanced Mechanisms
Mechanics & Manufacturing Methods of
Composites
Elective-II
4
4
a. Computer Graphics
b. Material Technology
c. Non-destructive Evaluation
Manufacturing Simulation Laboratory
4
4
Total Credits
26

(III & IV Semesters)

S. Course
Subject
No code
1
13D90401 Seminar

credits

16

13D90402 Project work

11

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
4

C
4

(9D04102) FINITE ELEMENT METHODS

UNIT - I
Formulation Techniques: Methodology, Engineering problems and governing
differential equations, finite elements., Variational methods-potential energy method,
Raleigh Ritz method, strong and weak forms, Galerkin and weighted residual methods,
calculus of variations, Essential and natural boundary conditions.
UNIT II
One-dimensional finite element methods: Bar elements, temperature effects. Element
matrices, assembling of global stiffness matrix, Application of boundary conditions,
Elimination and penalty approaches, solution for displacements, reaction, stresses,
temperature effects, Quadratic Element, Heat transfer problems: One-dimensional,
conduction and convection problems. Examples: - one dimensional fin,
UNIT III
Trusses: Element matrices, assembling of global stiffness matrix, solution for
displacements, reaction, stresses, temperature effects.
UNIT IV
Beams and Frames: Element matrices, assembling of global stiffness matrix, solution for
displacements, reaction, stresses.
UNIT - V
Two dimensional problems: CST, LST, four noded and eight nodded rectangular
elements, Lagrange basis for triangles and rectangles, serendipity interpolation functions.
Axisymmetric Problems: Axisymmetric formulations, Element matrices, boundary
conditions. Heat Transfer problems: Conduction and convection, examples: - twodimensional fin.
UNIT VI
Isoparametric formulation: Concepts, sub parametric, super parametric elements,
numerical integration.
UNIT VII
Finite elements in Structural Dynamics: Dynamic equations, eigen value problems, and
their solution methods, simple problems.
12

_____________________________________________________________2013-14

UNIT VIII
Convergence: Requirements for convergence, h-refinement and p-refinement, complete
and incomplete interpolation functions, pascals triangle.
Text Book:1) Finite element methods by Chandraputla & Belagondu.
References:
1.
J.N. Reddy, Finite element method in Heat transfer and fluid dynamics, CRC
press,1994
2. Zienckiwicz O.C. & R. L. Taylor, Finite Element Method, McGraw-Hill,1983.
3. J. N. Oden, Finite Element of Nonlinear continua, McGraw-Hill, New York, 1971
4. K. J. Bathe, Finite element procedures, Prentice-Hall, 1996

13

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
4

C
4

(9DBS101) COMPUTATIONAL METHODS

Unit I
Introduction to numerical methods applied to engineering problems: Examples,
solving sets of equations Matrix notation Determinants and inversion Iterative
methods Relaxation methods System of non-linear equations computer programs
Unit II
Numerical integration: Newton-Cotes integration formulas Simpsons rules, Gaussian
quadrature. Adaptive integration
Unit III
Optimization: One dimensional unconstrained optimization, multidimensional
unconstrained optimization direct methods and gradient search methods, constrained
optimization
Unit IV: Boundry value problems and charecteristic value problems: Shooting
method Solution through a set of equations Derivative boundary conditions Rayleigh
Ritz method Characteristic value problems.
Unit V
Numerical solutions of partial differential equations: Laplaces equations
Representations as a difference equation Iterative methods for Laplaces equations
poisson equation Examples Derivative boundary conditions Irregular and non
rectangular grids Matrix patterns, sparseness ADI method Finite element method.
Unit VI
Parabolic partial differential equations: Explicit method Crank-Nickelson method
Derivative boundary condition Stability and convergence criteria Finite element for
heat flow computer programs.
Unit VII
Hyperbolic partial differential equations: Solving wave equation by finite differencesstability of numerical method method of characteristics-wave equation in two space
dimensions-computer programs.

14

_____________________________________________________________2013-14

Unit VIII
Curve fitting and approximation of functions: Least square approximation fitting of
non-linear curves by least squares regression analysis- multiple linear regression, non
linear regression - computer programs.
TEXT BOOKS:
1. Steven C.Chapra, Raymond P.Canale Numerical Methods for Engineers Tata McGraw hill
2.Curtis F.Gerald, partick.O.Wheatly,Applied numerical analysisAddison-wesley,1989
3.Douglas J..Faires,Riched BurdenNumerical methodsBrooks/cole publishing
company,1998.Second edition.
References:
1.Ward cheney &David Kincaid Numerical mathematics and computingBrooks/cole
publishing company1999,fourth edition.

15

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
C
4
4
(9D04105) ADVANCES IN MANUFACTURING TECHNOLOGY

Unit I Welding Processes: Fusion and Solid state welding process, Automation in
Welding, Design aspects of welds, Weldability of aluminium alloys, titanium alloys and
High strength low alloy steels, Non destructive testing of welds, Residual stresses and
distortion in weldments.
Unit II Surface Processing Operations: Plating and Related Processes, Conversion
Coatings, Physical Vapor Deposition, Chemical Vapor Deposition, Organic Coatings,
Porcelain Enameling and other Ceramic coatings, Thermal and Mechanical Coating
Processes.
Unit III Un-conventional Machining Methods-I:
Abrasive jet machining - Elements of the process, mechanics of metal removal process
parameters, economic considerations, applications and limitations, recent developments.
Ultrasonic machining: Elements of the process, machining parameters, effect of
parameters on surface finish and metal removal rate, mechanics of metal removal process
parameters, economic considerations, applications and limitations.
Unit IV Un-conventional Machining Methods-II:
Electro-Chemical Processes: Fundamentals of electro chemical machining, metal removal
rate in ECM, Tool design, Surface finish and accuracy economics aspects of ECM.
Wire EDM Process: General Principle and applications of Wire EDM, Mechanics of metal
removal, Process parameters, selection of tool electrode and dielectric fluids, methods
surface finish and machining accuracy.
Unit V Un-conventional Machining Methods-III:
Electron Beam Machining: Generation and control of electron beam for machining, theory
of electron beam machining, principle, advantages, limitations, comparison of thermal and
non-thermal processes.
Unit VI Plasma Arc Machining: Principle, machining parameters, effect of machining
parameters on surface finish and metal removal rate, applications, limitations
Laser Beam Machining: Principle, effect of machining parameters on surface finish,
applications, and limitations.
16

_____________________________________________________________2013-14

Unit VII Rapid Prototyping: Working principle, methods-Steriolithography, Laser

sintering, Fused deposition method, applications and limitations.
Unit VIII Nano Technology: Nano milling processes, wet milling, dry milling, nano
materials, fabrication of nano tubes, advantages of nano tubes, mechanical properties.
Text Books:
1. Manufacturing Technology
- P. N. Rao, TMH Publishers
2. Fundamentals of Modern Manufacturing, Mikell P. Groover, John Wiley & Sons
Publishers
References:
1.Production Technology
2.Manufacturing Science
3.Welding Technology
4.Introduction to Nanotechnology -

- HMT
- Cambel
- R.S, Parmar,
Poole and Owens, Wiley (2003).

17

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
4

C
4

(9D15203) MECHANICAL VIBRATIONS

Unit I
Single degree of Freedom systems I: Undamped and damped free vibrations: forced
vibrations ; coulomb damping; Response to harmonic excitation; rotating unbalance and
support excitation ;Vibration isolation and transmissibility
Unit II
Single degree of Freedom systems II: Response to Non Periodic Excitations: unit Impulse,
unit step and unit Ramp functions; response to arbitrary excitations, The Convolution
Integral; shock spectrum; System response by the Laplace Transformation method.
Unit III
Vibration measuring instruments : Vibrometers, velocity meters & accelerometers
Unit IV
Two degree freedom systems: Principal modes undamped and damped free and forced
vibrations ; undamped vibration absorbers ;
Unit V
Multi degree freedom systems: Matrix formulation, stiffness and flexibility influence
coefficients; Eigen value problem; normal modes and their properties; Free and forced
vibration by Modal analysis; Method of matrix inversion; Torsional vibrations of multi
rotor systems and geared systems; Discrete-Time systems.
Unit VI
Numerical Methods: Raylieghs, stodolas, Matrix iteration, Rayleigh-Ritz Method and
Holzers methods.
Unit VII
Continuous systems: Free vibration of strings longitudinal oscillations of bars-traverse
vibrations of beamsTorsional vibrations of shafts.
Unit VIII
Critical speeds of shafts: Critical speeds without and with damping, secondary critical
speed.

18

_____________________________________________________________2013-14

Text books:
1. Elements of Vibration Analysis by Meirovitch.
2. Mechanical Vibrations by G.K. Groover.
References:
1. Vibrations by W.T. Thomson
2. Mechanical Vibrations Schaum series.
3. Vibration problems in Engineering by S.P. Timoshenko.
4. Mechanical Viabrations V.Ram Murthy.

19

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
4
(9D04201) ADVANCED OPTIMIZATION TECHNIQUES

C
4

UNIT - I
Linear programming: Two-phase simplex method, Big-M method, duality,
interpretation, applications.
UNIT - II
Assignment problem: Hungarians algorithm, Degeneracy, applications, unbalanced
problems, traveling salesman problem.
UNIT - III
Classical optimization techniques: Single variable optimization with and without
constraints, multi variable optimization without constraints, multi variable
optimization with constraints method of Lagrange multipliers, Kuhn-Tucker conditions.
UNIT - IV
Numerical methods for optimization: Nelder Meads Simplex search method, Gradient
of a function, Steepest descent method, Newtons method, types of penalty methods for
handling constraints.
UNIT - V
Genetic algorithm (GA) : Differences and
similarities between conventional and
evolutionary algorithms, working principle, reproduction, crossover, mutation,
termination criteria, different reproduction and crossover operators, GA for constrained
optimization, draw backs of GA,
UNIT - VI
Genetic Programming (GP): Principles of genetic programming, terminal sets,
functional sets, differences between GA & GP, random population generation, solving
differential equations using GP.
UNIT VII
Multi-Objective GA: Paretos analysis, Non-dominated front, multi objective GA,
Non-dominated sorted GA, convergence criterion, applications of multi-objective
problems .
UNIT VIII
Applications of Optimization in Design and Manufacturing systems: Some typical
applications like optimization of path synthesis of a four-bar mechanism, minimization of
20

_____________________________________________________________2013-14

weight of a cantilever beam, optimization of springs and gears, general optimization

model of a machining process, optimization of arc welding parameters, and general
procedure in optimizing machining operations sequence.
Text Books:
1. Optimal design Jasbir Arora, Mc Graw Hill (International) Publishers
2. Optimization for Engineering Design Kalyanmoy Deb, PHI Publishers
3. Engineering Optimization S.S.Rao, New Age Publishers
References:
1.Genetic algorithms in Search, Optimization, and Machine learning D.E.Goldberg,
Addison-Wesley Publishers
2. Genetic Programming- Koza
3. Multi objective Genetic algorithms - Kalyanmoy Deb, PHI Publishers.

21

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
4

C
4

(9D04108) DESIGN FOR MANUFACTURING

(Elective-I)
UNIT - I
Introduction: Design philosophy-steps in design process-general design rules for
manufacturability-basic principles of designing for economical production-creativity in
design.
UNIT - II
Materials: Selection of materials for design-developments in material technology-criteria
for material selection-material selection interrelationship with process selection-process
selection charts.
UNIT - III
Machining processes: Overview of various machining processes-general design rules for
machining-dimensional tolerance and surface roughness-Design for machining ease
redesigning of components for machining ease with suitable examples. General design
recommendations for machined parts.
UNIT - IV
Metal casting: Appraisal of various casting processes, selection of casting process,-general
design considerations for casting-casting tolerance-use of solidification, simulation in
casting design-product design rules for sand casting.
UNIT - V
Metal joining: Appraisal of various welding processes, factors in design of weldments
general design guidelines-pre and post treatment of welds-effects of thermal stresses in
weld joints-design of brazed joints.
UNIT VI
Forging: Design factors for forging closed die forging design parting lines of dies
drop forging die design general design recommendations.
UNIT VII
Extrusion & Sheet metal work: Design guide lines extruded sections-design principles
for punching, blanking, bending, deep drawing-Keeler Goodman forging line diagram
component design for blanking.
22

_____________________________________________________________2013-14

UNIT VII
Plastics: Visco elastic and creep behavior in plastics-design guidelines for plastic
components-design considerations for injection moulding design guidelines for
machining and joining of plastics.
Text Books:
1. Design for manufacture, John cobert, Adisson Wesley. 1995
2. Design for Manufacture by Boothroyd,
References:
1. ASM Hand book Vol.20

23

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
4

C
4

(9D04206) RAPID PROTOTYPING

(Elective-I)
Unit-I
Introduction: Need for the compression in product development, History of RP system,
Survey of applications, Growth of RP industry and classification of RP system.
Unit II
Stereo Lithography System: Principle, Process parameter, Process details, Data
preparation, Data files and machine details, Applications.
Unit III
Fusion Decomposition Modeling: Principle, process parameter, Path generation,
Applications.
Unit IV
Solid ground curing: Principle of operation, Machine details, Applications,
Laminated Object Manufacturing: Principle of Operation, LOM materials, Process
details, Applications.
Unit V
Concepts Modelers: Principle, Thermal jet printer, Sanders model market, 3-D printer,
Genisys Xs printer HP system 5, Object Quadra system.
Unit VI
LASER ENGINEERING NET SHAPING (LENS)
Rapid Tooling: Indirect Rapid tooling- Silicon rubber tooling- Aluminum filled epoxy
tooling Spray metal tooling, Cast kriksite, 3Q keltool, etc, Direct Rapid Tooling Direct.
AIM, Quick cast process, Copper polyamide, Rapid Tool, DMILS, Prometal, Sand casting
tooling, Laminate tooling soft, Tooling vs. hard tooling.
Software for RP: STL files, Overview of Solid view, magics, imics, magic
communication, etc. Internet based software, Collaboration tools.
Unit VII
24

_____________________________________________________________2013-14

Rapid Manufacturing Process Optimization: Factors influencing accuracy, Data

preparation error, Part building error, Error in finishing, Influence of build orientation.
Unit VIII
Allied Process: Vacuum casting, surface digitizing, Surface generation from point cloud,
Surface modification- Data transfer to solid models.
TEXT BOOKS:
1. Paul F.Jacobs stereo lithography and other RP & M Technologies, SME,
NY 1996
2. Flham D.T & Dinjoy S.S Rapid Manufacturing Verlog London 2001
3. Lament wood, Rapid automated , Indus Press New York.

25

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

Th
C
4
4
(12D87207) DESIGN AND MANUFACTURING OF MEMS AND MICRO
SYSTEMS
(Elective-I)

UNIT - I:
Overview and working principles of MEMS and Microsystems: MEMS and
Microsystems, Evolution of Micro fabrication, Microsystems and Microelectronics,
Microsystems and miniaturization, Applications of MEMs in Industries, Micro sensors,
Micro actuation, MEMS with Micro actuators Micro accelerometers, Micro fluidics
UNIT - II:
Engineering Science for Microsystems Design and Fabrication: Atomic structure of
Matter, Ions and Ionization, Molecular Theory of Matter and Intermolecular Forces,
Doping of Semiconductors, The Diffusion Process, Plasma Physics, Electrochemistry,
Quantum Physics.
UNIT - III:
Engineering Mechanics for Microsystems Design: Static Bending of Thin plates,
Mechanical Vibration, Thermo mechanics , Fracture Mechanics, Thin- Film Mechanics,
Overview of Finite Element Stress Analysis
UNIT - IV:
Thermo Fluid Engineering and Microsystems Design: Overview of Basics of Fluid
Mechanics in Macro and Mesoscales, Basic equations in Continuum Fluid Dynamics,
Laminar Fluid Flow in Circular Conduits, Computational Fluid Dynamics, Incompressible
Fluid Flow in Micro conduits, Fluid flow in Sub micrometer and Nano scale,
UNIT V
Overview of Heat conduction in Solids, Heat Conduction in Multilayered Thin films and
in solids in sub micrometer scale, Design Considerations, Process Design
UNIT VI
Mechanical Design, Mechanical design using FEM, Design of a Silicon Die for a Micro
pressure sensor.
UNIT VII & VIII
Materials for MEMS and Microsystems and their fabrication: Substrates and Wafers,
Active substrate materials, Silicon as a substrate material, Silicon compounds, Silicon
Piezo resistors, Gallium Arsenide, Quartz, Piezoelectric Crystals and Polymers,

26

_____________________________________________________________2013-14

Photolithography, Ion implantation, Diffusion and oxidation, Chemical and Physical

vapor deposition, etching, Bulk micro manufacturing, Surface Micromachining, The
LIGA Process.
TEXT BOOK:
1. MEMS and Microsystems. Design and Manufacturing, Tia-Ran Hsu, TMH 2002
2. Foundation of MEMS, Chang Liu,Pearson, 2012

27

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- I Sem (PEED)

L
3

C
2

(13D90101) DESIGN SIMULATION LABORATORY

I. Modeling
1.Surface modeling
2.Solid modeling
3.Drafting
4.Assembling
II. Structural Analysis using any FEA Package for different structures that can be
discretised with 1-D,2-D & 3-D elements
1. Static Analysis
2. Modal Analysis
3. Harmonic Analysis
4. Spectrum Analysis
5. Buckling Analysis
6. Analysis of Composites
7. Fracture mechanics
References :
User manuals of ANSYS package Version 10.0
PRO/E, I-DEAS Package /UNIGRAPHICS,CATIA

28

_____________________________________________________________2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(12D87208) INDUSTRIAL ROBOTICS

UNIT - I: Introduction: Automation and Robotics, Robot anatomy, robot configuration,
motions joint notation work volume, robot drive system, control system and dynamic
performance, precision of movement.
UNIT-II: CONTROL SYSTEM AND COMPONENTS: basic concept and modals
controllers control system analysis, robot actuators and feedback components (sensors):
Internal and External Sensors, Positions sensors, velocity sensors - Desirable features,
tactile, proximity and range sensors, uses sensors in robotics , Power Transmission
Systems.
UNIT - III: MOTION ANALYSIS AND CONTROL: Manipulator kinematics, position
representation Homogeneous transformation, D-H Notation, D-H Transformation Matrix,
Forward and Inverse transformations, problems on planar and spatial manipulators,
UNIT-IV: Differential Kinematics, Jacobian Formulation, problems, manipulator path
control: Slew, Joint Interpolated and Straight line motions, trajectory planning: Joint space
scheme, Cartesian space scheme, Cubic Polynomial fit without and with via point,
blending.
UNIT - V: ROBOT DYNAMICS: Lagrange Euler and Newton Euler formulations,
problems on two link planar manipulators, configuration of robot controller.
UNIT-VI: END EFFECTORS: Grippers-types, operation, mechanism, force analysis,
tools as end effectors consideration in gripper selection and design.
MACHINE VISION: Functions, Sensing and Digitizing-imaging, Devices, Lighting
techniques, Analog to digital single conversion, Image storage, Image processing and
Analysis-image data reduction, Segmentation feature extraction. Object recognition,
training the vision system, Robotics application.
UNIT - VII: ROBOT PROGRAMMING: Lead through programming, Robot
programming as a path in space, Motion interpolation, WAIT, SINGNAL AND DELAY
commands, Branching capabilities and Limitations.
ROBOT LANGUAGES: Textual robot languages, Generation, Robot language structures,
Elements and functions.
UNIT - VIII: ROBOT CELL DESGIN AND CONTROL: Robot cell layouts-Robot
centered cell, In-line robot cell, Considerations in work cell design, Work cell control,
Inter locks, Error detection, Work cell controller.
29

2013-14_____________________________________________________________

ROBOT APPLICATIONS: Material transfer, Machine loading/unloading. Processing

operations, Assembly and Inspection, Future Applications.
TEXT BOOKS:
1. Introduction to Robotics Mechanics and Control, John J.Craig, Pearson
2. Industrial robotics , Mikell P.Groover , McGraw Hill.
3. Modelling and Control of Robot Manipulators, L.Sciavicco & B.Siciliano,Springer
REFERENCE BOOKS:
1. Robotics , K.S.Fu , McGraw Hill.
2. Robot Analysis, Lung Wen Tsai, John Wiley & Sons
3. Robotics and control ,RK Mittal & IJ Nagrath, Tata McGrawHill
4. Fundamentals of Robotics,Robert J.schilling,PHI
5. Robotics ,Saha, TMG
6. Robotic Engineering, Richard D.Klafter, Thomas A.Chmielewski,PHI

30

_____________________________________________________________2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(12D87101) AUTOMATION IN MANUFACTURING

UNIT-I:
Introduction to Automation: Automation in Production Systems-Automated
Manufacturing Systems, Computerized Manufacturing Support Systems, Reasons for
Automation, Automation Principles and Strategies.
UNIT-II
Manufacturing operations, Production Concepts and Mathematical Models. Costs of
Manufacturing Operations, Basic Elements of an Automated Systems, Advanced
Automation Functions, Levels of automation.
UNIT-III:
Introduction to Material Handling, Overview of Material Handling Equipment,
Considerations in Material Handling System Design, The 10 Principles of Material
Handling. Material Transport Systems, Automated Guided Vehicle Systems, Monorails
and other Rail Guided Vehicles, Conveyor Systems, Analysis of Material Transport
Systems.
UNIT-IV
Storage Systems, Storage System Performance, Storage Location Strategies, Conventional
Storage Methods and Equipment, Automated Storage Systems, Engineering Analysis of
Storage Systems. Automatic data capture-overview of Automatic identification methods,
bar code technology, other ADC technologies.
UNIT -V:
Manual Assembly Lines - Fundamentals of Manual Assembly Lines, Alternative
Assembly Systems, Design for Assembly, Analysis of Single Model Assembly Lines,
UNIT-VI
Line balancing problem, largest candidate rule, Kilbridge and Wester method, and Ranked
Positional Weights Method, Mixed Model Assembly Lines, Considerations in assembly
line design.
UNIT-VII:
Transfer lines, Fundamentals of Automated Production Lines, Storage Buffers, and
Applications of Automated Production Lines. Analysis of Transfer Lines with no Internal
Storage, Analysis of Transfer lines with Storage Buffers.
UNIT-VIII:
Automated Assembly Systems, Fundamentals of Automated Assembly Systems, Design
for Automated Assembly, and Quantitative Analysis of Assembly Systems - Parts
31

2013-14_____________________________________________________________

Delivery System at Work Stations, Multi- Station Assembly Machines, Single Station
Assembly Machines , Partial Automation.
TEXT BOOKS:
1. Automation, Production systems and computer integrated manufacturing, Mikel P.
Groover, Pearson Eduction.
REFERENCE BOOKS:
1. CAD CAM : Principles, Practice and Manufacturing Management, Chris Mc Mohan,
Jimmie Browne , Pearson edu. (LPE)
2. Automation, Buckinghsm W, Haper & Row Publishers, New York, 1961
3. Automation for Productivity, Luke H.D, John Wiley & Sons, New York, 1972.

32

_____________________________________________________________2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(12D87203) SIMULATION AND MODELLING OF MANUFACTURING

SYSTEMS
UNIT - I:
System ways to analyze the system Model - types of models Simulation Definition
Types of simulation models steps involved in simulation Advantages and
Disadvantages.
UNIT-II
Parameter estimation estimator properties estimate point estimate confidence
interval estimates independent dependent hypothesis types of hypothesis- steps
types 1 & 2 errors Framing Strang law of large numbers.
UNIT - III:
Building of Simulation model validation verification credibility their timing
principles of valid simulation Modeling Techniques for verification statistical
procedures for developing credible model.
UNIT-IV
Modeling of stochastic input elements importance various procedures theoretical
distribution continuous discrete their suitability in modeling.
UNIT - V:
Generation of random variants factors for selection methods inverse transform
composition convolution acceptance rejection generation of random variables
exponential uniform Weibull normal Bernoullie Binomial uniform Poisson.
UNIT-VI
Simulation languages comparison of simulation languages with general purpose
languages Simulation languages vs Simulators software features statistical
capabilities G P S S SIMAN- SIMSCRIPT Simulation of M/M/1 queue comparison
of simulation languages.QUEST, WITNESS, PROMODEL and AUTOMOD
UNIT - VII :
Output data analysis Types of Simulation with respect to output data analysis warm up
period- Welch algorithm Approaches for Steady State Analysis replication Batch
means methods comparisons
UNIT VIII :
Applications of Simulation flow shop system job shop system M/M/1 queues with
infinite and finite capacities Simple fixed period inventory system Newboy paper
problem.
33

2013-14_____________________________________________________________

TEXT BOOKS:
1. Simulation Modelling and Analysis, Law, A.M.& Kelton , McGraw Hill, 2nd Edition,
New York, 1991.
2. Discrete Event System Simulation, Banks J. & Carson J.S., PH , Englewood Cliffs, NJ,
1984.
3. Simulation of Manufacturing Systems, Carrie A. , Wiley, NY, 1990.
4. A Course in Simulation, Ross, S.M., McMillan, NY, 1990.
5. Simulation Modelling and SIMNET , Taha H.A. , PH, Englewood Cliffs, NJ, 1987
6, Performance modeling and analysis of manufacturing systems,Viswanatham & Narahari,PHI

34

_____________________________________________________________2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(9D15102) ADVANCED MECHANISMS

Unit I: Introduction: Elements of Mechanisms; Mobility Criterion for Planar
mechanisms and manipulators; Mobility Criterion for spatial mechanisms and
manipulators. Spherical mechanisms-spherical trigonometry.
Unit II: Advanced Kinematics of plane motion- I: The Inflection circle ; Euler
Savary Equation; Analytical and graphical determination of di ; Bobilliers Construction
;Collineastion axis ; Hartmanns Construction ;Inflection circle for the relative motion of
two moving planes; Application of the Inflection circle to kinematic analysis.
Unit III: Advanced Kinematics of plane motion - II: Polode curvature; Halls
Equation; Polode curvature in the four bar mechanism; coupler motion; relative motion of
the output and input links; Determination of the output angular acceleration and its Rate of
change; Freudensteins collineation axis theorem; Carter Hall circle; The circling
point curve for the Coupler of of a four bar mechanism.
Unit IV: Introduction to Synthesis-Graphical Methods - I: The Four bar linkage
;Guiding a body through Two distinct positions; Guiding a body through Three distinct
positions; The Rotocenter triangle ; Guiding a body through Four distinct positions;
Burmesters curve.
Unit V: Introduction to Synthesis-Graphical Methods - II: Function generationGeneral discussion; Function generation: Relative rotocenter method, Overlays method,
Function generation- Velocity pole method; Path generation: Hroness and Nelsons
motion Atlas, Robertss theorem.
Unit VI: Introduction to Synthesis - Analytical Methods: Function Generation:
Freudenstiens equation, Precision point approximation, Precision derivative
approximation; Path Generation: Synthesis of Four-bar Mechanisms for specified
instantaneous condition; Method of components; Synthesis of Four-bar Mechanisms for
prescribed extreme values of the angular velocity of driven link; Method of components.
Unit VII: Manipulator kinematics I: D-H notation, D-H convention of assignment
of co-ordinate frames and link parameters table;D-H transformation matrix ; Direct and
Inverse kinematic analysis of Serial manipulators: Articulated ,spherical & industrial robot
manipulators- PUMA, SCARA,STANFORD ARM, MICROBOT.
Unit VIII: Manipulator kinematics II: Differential kinematics Formulation of
Jacobian for planar serial manipulators and spherical manipulator; Singularity analysis.
35

2013-14_____________________________________________________________

Text Books:
1. Jeremy Hirschhorn, Kinematics and Dynamics of plane mechanisms, McGrawHill,1962.
2. L.Sciavicco and B.Siciliano, Modelling and control of Robot manipulators, Second
edition ,
Springer -Verlag,London,2000.
3. Amitabh Ghosh and Ashok Kumar Mallik, Theory of Mechanisms and Machines.
E.W.P.Publishers.
Reference Books:
1. Allen S.Hall Jr., Kinematics and Linkage Design, PHI,1964.
2. J.E Shigley and J.J . Uicker Jr., Theory of Machines and Mechanisms , McGraw-Hill,
1995.
3. Mohsen Shahinpoor, A Robot Engineering Text book,Harper & Row Publishers, New
York,1987.
4. Joseph Duffy, Analysis of mechanisms and Robot manipulators, Edward Arnold,1980

36

_____________________________________________________________2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(9D04208) MECHANICS AND MANUFACTURING METHODS OF

COMPOSITES
Unit I
Basic concepts and characteristics: Geometric and Physical definitions, natural and
man-made composites, Aerospace and structural applications, types and classification of
composites,
Unit II
Reinforcements: Fibres- Glass, Silica, Kevlar, carbon, boron, silicon carbide, and born
carbide fibres. Particulate composites, Polymer composites, Thermoplastics, Thermosetts,
Metal matrix and ceramic composites.
Unit III
Micromechanics: Unidirectional composites, constituent materials and properties, elastic
properties of a lamina, properties of typical composite materials, laminate characteristics
and configurations. Characterization of composite properties.
Unit IV
Coordinate transformations: Hookes law for different types of materials, Hookes law
for two dimensional unidirectional lamina, Transformation of stress and strain, Numerical
examples of stress strain transformation, Graphic interpretation of stress strain relations.
Off - axis, stiffness modulus, off - axis compliance.
Unit V
Elastic behavior of unidirectional composites: Elastic constants of lamina, relation ship
between engineering constants and reduced stiffness and compliances, analysis of
laminated composites, constitutive relations.
Unit VI
Strength of unidirectional lamina: Micro mechanics of failure, Failure mechanisms,
Strength of an orthotropic lamina, Strength of a lamina under tension and shear maximum
stress and strain criteria, application to design. The failure envelope, first ply failure, freeedge effects. Micro mechanical predictions of elastic constants.
Unit VII
Analysis of laminated composite plates
Introduction, thin plate theory, specially orthotropic plate, cross and angle ply laminated
plates, problems using thin plate theory.

37

2013-14_____________________________________________________________

Unit VIII
Manufacturing methods: Autoclave, tape production, moulding methods, filament
winding, man layup, pultrusion, RTM.
Text Books:
1. R. M. Jones, Mechanics of Composite Materials, Mc Graw Hill Company, New York,
1975.
2. Engineering Mechanics of Composite Materials by Isaac and M.Daniel, Oxford
University Press, 1994.
References:
1. B. D. Agarwal and L. J. Broutman, Analysis and performance of fibre Composites,
Wiley-Interscience, New York, 1980.
2. L. R. Calcote, Analysis of Laminated Composite Structures, Van Nostrand Rainfold,
New York, 1969.

38

_____________________________________________________________2013-14

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(9D04203) COMPUTER GRAPHICS

(Elective-II)
Unit - I
Introduction to computer graphics: Color CRT raster scan monitors, plasma display &
liquid crystal display monitors, computer input devices, hard copy devices.
Unit - II
Raster scan graphics: Line drawing algorithms DDA & Bresenham algorithms, circle
generation, general function rasterization, displaying lines, characters and polygons.
Unit - III
Filling algorithms: polygon filling, edge fill algorithm, seed fill algorithm, fundamentals
of antialiasing and half toning.
Unit - IV
Line CLIPPING: Simple visibility algorithm, Cohen-Sutherland subdivision line
clipping algorithm, mid point sub division algorithm.
Unit - V
Polygon clipping: polygon clipping, reentrant polygon clipping Sutherland
Hodgeman algorithm, character clipping, 3D- clipping.
Unit - VI
Transformations: Cartesian and homogeneous coordinate systems two dimensional and
three dimensional transformations scaling, rotation, Shearing, Zooming, viewing
transformation, reflection, rotation about an axis, concatenation.
Unit - VII
Rendering: Hidden line removal algorithms, surface removal algorithms, painters,
Warnock, Z-buffer algorithm.
Unit - VIII
Shading algorithms: Constant intensity algorithm, Phongs shading algorithm, gourand
shading algorithm, Comparison of shading algorithms.
Text Books:
1.Procedural elements for computer graphics-D.F.Rogers, Tata McGraw-Hill.
2.Computer Graphics-Donald Hearn & M.P. Bakers.
3.Computer graphics-Harrington.
39

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(13D90201) MATERIAL TECHNOLOGY

(Elective-II)
UNIT I:
Elasticity in metals and polymers, mechanism of plastic deformation, role of dislocations,
yield stress, shear strength of perfect and real crystals, strengthening mechanism, work
hardening, solid solution, grain boundary strengthening
UNIT-II
Poly phase mixture, precipitation, particle, fiber and dispersion strengthening, effect of
temperature, strain and strain rate on plastic behavior, super plasticity, deformation of non
crystalline material.
UNIT III:
Griffths Theory, stress intensity factor and fracture Toughness, Toughening Mechanisms,
Ductile and Brittle transition in steel, High Temperature Fracture, Creep, Larson Miller
Parameter, Deformation and Fracture mechanism maps.
UNIT IV:
Fatigue, Low and High cycle fatigue test, Crack Initiation and Propagation mechanism
and Paris Law, Effect of surface and metallurgical parameters on Fatigue, Fracture of nonmetallic materials, fatigue analysis, Sources of failure, procedure of failure analysis.
.
UNIT V:
Selection for Surface durability, Corrosion and Wear resistance, Relationship between
Materials Selection and Processing, Case studies in Materials Selection with relevance to
Aero, Auto, Marine, Machinery and Nuclear Applications.
Motivation for selection, cost basis and service requirements, Selection for Mechanical
Properties, Strength, Toughness, Fatigue and Creep
UNIT VI:
Modern Metallic Materials: Dual Phase Steels, Micro alloyed, High Strength Low alloy
(HSLA) Steel, Transformation induced plasticity (TRIP) Steel, Maraging Steel,
Intermetallics, Ni and Ti Aluminides
UNIT-VII
Smart Materials, Shape Memory alloys, Metallic Glass, Quasi Crystal and Nano
Crystalline Materials. Metal-Matrix composites

40

_____________________________________________________________2013-14

UNIT-VIII
Nonmetallic Materials: Polymeric materials and their molecular structures, Production
Techniques for Fibers, Foams, Adhesives and Coatings, Structure, Properties and
Applications of engineering Polymers
TEXT BOOKS:
1. Mechanical Behaviour of Materials, Thomas H. Courtney, 2nd Edition, McGraw
Hill,2000.
2. Mechanical Metallurgy, George E. Dieter, McGraw Hill,1998.
REFERENCE BOOK:
1. Selection and use of Engineering Materials,Charles J.A, Butterworth Heiremann

41

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

Th
4

C
4

(9D15108) NON - DESTRUCTIVE EVALUATION

(Elective-II)
Unit I
Ultra Sonic Hardness Testing: Flaw Detection Using Dye Penetrants. Magnetic Particle
Inspection introduction to electrical impedance, Principles of Eddy Current testing, Flaw
detection using eddy currents.
Unit II
Introduction to X-Ray Radiography: The Radiographic process, X-Ray and Gamma-ray
sources, Geometric Principles, Factors Governing Exposure, Radio graphic screens,
Scattered radiation, Arithmetic of exposure, Radiographic image quality and detail
visibility, Industrial X-Ray films,
Unit III
X-Ray Radiography processes: Fundamentals of processing techniques, Process control,
The processing Room, Special Processing techniques, Paper Radiography, Sensitometric
characteristics of x-ray films, Film graininess signal to noise ratio in radiographs, The
photographic latent image, Radiation Protection,
Unit IV
Introduction to Ultrasonic Testing: Generation of ultrasonic waves, Horizontal and
shear waves, Near field and far field acoustic wave description, Ultrasonic probes- straight
beam, direct contact type, Angle beam, Transmission/reflection type, and delay line
transducers, acoustic coupling and media,
Unit V
Ultrasonic tests: Transmission and pulse echo methods, A-scan, B-scan, C-scan, F-scan
and P-scan modes, Flaw sizing in ultrasonic inspection: AVG, Amplitude, Transmission,
TOFD, Satellite pulse, Multi-modal transducer, Zonal method using focused beam. Flow
location methods, Signal processing in Ultrasonic NDT; Mimics, spurious echos and
noise. Ultrasonic flaw evaluation.
Unit VI
Holography: Principles and practices of Optical holography, acoustical, microwave, xray and electron beam holography techniques.
Unit VII
Applications - I: NDT in flaw analysis of Pressure vessels, piping
Unit VIII
Applications - II: NDT in Castings, Welded constructions, etc., Case studies.
42

_____________________________________________________________2013-14

Text books:
1. Ultrasonic testing by Krautkramer and Krautkramer
2. Ultrasonic inspection 2 Training for NDT : E. A. Gingel, Prometheus Press,
3. ASTM Standards, Vol 3.01, Metals and alloys

43

2013-14_____________________________________________________________

JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY ANANTAPUR

M.Tech- II Sem (PEED)

L
3

C
2

(12D87209) MANUFACTURING SIMULATION LAB

1.Study of elements , entities , activities and basic models of a simulation package
modeling
and simulation
2.Throughput analysis of a individual production facility using simulation.
3. Modeling of a typical manufacturing facility and study its performances.
4. Breakdown analysis of a production facility with one machine
5. Breakdown analysis of a production system having multiple machines
6.Modeling and Simulation of layouts
7.Study of transport system in a shop floor
8.Buffer size design
9.Identification of bottleneck machine on a given shop floor
10.Study of conjunction, collision and dead locks through simulation
Lab Facilities
Adequate number of Computer Systems in Networked Environment
Packages : 1. QUEST
2.PROMODEL
3.FLEXSIM
4.AUTOMOD
5.WITNESS

44