See

discussions, stats, and author profiles for this publication at: http://www.researchgate.net/publication/277141436

Automatic Energy Meter Reading using Smart

Energy Meter
CONFERENCE PAPER MARCH 2014
DOI: 10.13140/RG.2.1.1343.7928

READS

187

3 AUTHORS, INCLUDING:
Zahid Iqbal Rana

Muhammad Waseem

University of Engineering and Technology, T

University of Engineering and Technology, T

3 PUBLICATIONS 0 CITATIONS

1 PUBLICATION 0 CITATIONS

SEE PROFILE

SEE PROFILE

Available from: Zahid Iqbal Rana

Retrieved on: 25 November 2015

Automatic Energy Meter Reading using Smart Energy

Meter
H. M. Zahid Iqbal

M. Waseem

Tahir Mahmood

Department of Electrical Engineering

Department of Electrical Engineering

Department of Electrical Engineering

University of Engineering & Technology

Taxila, Pakistan
[email protected]

University of Engineering & Technology

Taxila, Pakistan
[email protected]

University of Engineering & Technology

Taxila, Pakistan
[email protected]

Abstract - An automatic remote meter-reading system based

on GSM is presented in this paper. This paper is useful to obtain
meter reading when desired so meter readers dont need to visit
each customer for the consumed energy data collection and to
distribute the bill slips. Microcontroller can be used to monitor
and record the meter readings. In case of a customer defaulter, no
need to send a person of utility to cut-off the customer connection.
Utility can cut off and reconnect the customer connection by short
message service (SMS). Furthermore, the customer can check the
status of electricity (load) from anywhere. In this system energy
meter readings are being transferred by making use of GSM.
Index Terms - Smart Energy Meter (SEM), Automatic Meter
Reading (AMR), Global System for Mobile (GSM), Short
Messaging System (SMS).

I. INTRODUCTION
Utility billing is yet unavoidable in the World as for
concern post-paid energy meter. In Pakistan, utilities are using
a conventional way of billing. A meter reader goes Home to
home takes the meter reading and note down it, manually.
These readings are brought to utility administration office. The
criterion of utility billing is applied according to the utility
service rules and regulations. The employee of the utility goes
door to door again and gave the bill slips of the utility to the
respective consumer. [1-3]
Detailed load flow can be provided by smart energy meters to
the consumers so they can manage their load effectively [4].
Smart energy meter are used for Automatic Meter Reading
(AMR) to increase the accuracy of meter reading. For instance,
a utility person might not read the correct value of the total
energy consumed that is displayed on energy meter or may
intentionally give lower value than the exactly read one [5].
Power Line Communication (PLC) can also be used for
obtaining the meter readings but interference and noise makes
it inadequate. Metering information can be transmitted via
Wi-Fi and Zig-Bee but their range is limited and they do not
provide a cost effective solution [6]. However for lager remote
distance GSM communication system is much efficient than
others.
Auto billing is one of the suitable ways to overcome the flaws
of conventional billing; since conventional billing contains
wastage of time and resources as well. In auto billing there is
no more need of manual meter reading and bill slips.

1.1 FLAWS IN CONVENTIONAL BILLING.

There are many flaws and errors in conventional billing. Some
human mistakes may also occur in manual billing. Analysing
the conventional billing some of the common observed errors
and mistakes are:
Its a time consuming procedure
There is always a chance of human error while taking
the manual meter reading
There is no check and balance and verification
procedure of this meter reading
There is always a chance of theft and corruption
Extra human power is required
Consumer is not updated of his usage
Consumer may not get the bill slip within due date
II. SMART ENERGY METER
The size of smart meters and traditional meters is same and
smart meters are digital [7]. Smart Energy Meter measures
more detailed readings than Kwhr so that utility can plan the
expansion of network and power quality [8],[9],[10]. The
Smart Energy Meter is designed so that it measures voltage
and load currents by the use of voltage and current sensors
instead of potential and current transformers and then feeds
these values of voltage and current into power factor controller
IC and energy metering IC the power factor and power
calculations respectively [11].

Figure 1. Simple block diagram of Smart Energy Meter.

The design of Smart Energy Meter involves the measuring of

load current and voltage using sensors and then feeding them
to energy metering IC which converts it into the real power
consumed by the load. Power factor is measured by measuring
the phase shift between voltage and load current.
Microcontroller used to perform the calculations related to
power and energy consumed and shows the reading on LCD as
well as it sends the reading of Smart Energy Meter with the
help of GSM modem [12]. Active power, reactive power,
voltage, load current, power factor and units (kWh) are
measured and displayed successfully. Meter reading are sent
from GSM modem and received on mobile successfully.
Two-way communication is done by smart energy meter
between the meter and utility administration as well as
between meter and customer so that customer is able to check
the status of his consumed energy units and can manage his
load accordingly to reduce his bill. [13],[14].
The main features of smart energy meter are listed as follows;

Get automatic reading of Energy Meter and sent it to

consumer as well as to utility.
In reading it measures Voltage, Load Current, Real
power, Reactive power, Power factor and units
consumed.
Utility is able to cutoff/restore the supply of the
defaulter through SMS.
Smart Energy Meter responds to the SMS and sends
you back the readings whenever it is asked.
Consumer is able to check the status of his load from
anywhere in the world by SMS.

2.1. Working of Smart Meter.

GSM communications network is used to transfer the
electricity consumed data to the utility administration as well
as to the customer when demanded. Antenna, attached on or
near meter box, can be used for improvement of signal
strength in GSM communication.
Smart metering communication is centralized meter reading,
so meter readers dont need to visit each customer for data
collection. However, for testing and maintenance meters may
need to observe occasionally.
The main duty of Smart Energy Meter is to measure the meter
reading and sends it to utility when demand as well as to
costumer. The voltage and current sensors measure the RMS
values of voltage and current and feed them to microcontroller,
where calculations for active and reactive power are
performed. In Smart Energy Meter we used sensors to measure
voltage and current instead of current and voltage
transformers. The reading from
Utility administration SMS is being received by smart energy
meter programmable interface and the action is performed by
the meter according to provided information.
A major feature of Smart Energy Meter is that utility company
can cut off and reconnect the connection of energy of any user
with the help of SMS without sending the person to perform
the task manually [15]. It can be utilized in case when the
utility company needs to disconnect a consumer due to nonpayment of bills or some other reasons. Another major feature
of Smart energy meter is that it gives alarm when the consumer
load is exceeding the upper limit for which he got the utility
connection [16]. In case consumer does not reduce his load
meter automatically cut off the consumer connection. GSM

Figure 2: Detailed Circuit diagram of Smart Energy Meter

communications network is used to transfer the electricity

consumed data to the utility administration as well as to the
customer when demanded. Antenna, attached on or near meter
box, can be used for improvement of signal strength in GSM
communication.

Figure 3(a) The sine wave of voltage and current.

Figure 3(b) Showing the phase difference between voltage and current

III. MAIN PARTS OF SMART ENERGY METER

Smart Energy Meter is comprised of three main parts:
A. Voltage and current measurements
B. Power factor measurements
C. GSM portion
A) Voltage and current measurements.
In our project we used current and voltage sensor to measure
voltage and load current. We used ACS712ELC-20A as
current sensor that gives us RMS value of currents. Both AC
and DC signals current measurement is precisely obtained by
this current sensor. Current is measured by this sensor up to
20A. Overall power consumption, metering and measurements
are taken by these sensors. Sensitive measurements of current
are handled by using OPAMP stage. By adjusting the gain we
measure very small currents. ACS712ELC-20A output voltage
has linear variation with measured currents. Similarly we
measured voltage by ACS712ELC-20A.
B) Power factor measurements.
Power factor is the cosine of angle between voltage and
current. It actually measures how effectively the power is
being converted into useful work. In our project we measured
it by taking XOR of voltage and current waves with the help of
microcontroller and LM358. We used LM 358 to convert
weak sinusoidal signals to large square signals.
After XOR we get signal of double frequency as shown in
figure 4 (c). We calculated the time of XOR signal and it is the
power factor. For 50Hz the output of XOR can be 10 ms if
power factor is 0. And 0 if power factor is unity. So the
output of XOR lies between 0 -1 for a certain value of power
factor.

Figure 3(a)

Figure 3(b

Fig. 4 (a,b & c). The square wave of voltage and current and their resultant
after XOR operation.

C) Wireless portion.
There are many technologies that are being used for AMR as
Power Line Carrier (PLC) communications, Supervisory
Control And Data Acquisition (SCADA),telephone modem,
internet, Ethernet, Embeded RF Module, WiFi, Bluetooth, and
ZigBee [17-22].
Power Line Carrier (PLC) and Telephone Line Network are
the example of wire-based AMR system and GSM and
Bluetooth are the examples of wireless AMR system [23]. The
transmission system of Smart Energy Meter utilizes the
existing GSM network. A GSM modem is used as mobile
equipment/ Data Communication Equipment to send the
information regarding the numbers of units of electricity
consumed to our desired mobile number [24-31]. We used
SIM900 GSM modem in our project. A SIM is used inside the
modem for data communication.
Power Line Communication (PLC) can also be used for
obtaining the meter readings but interference and noise makes
it inadequate [32],[33]. Metering information can be
transmitted via Wi-Fi and ZigBee but their range is limited and
they do not provide a cost effective solution [34]. However for
lager remote distance GSM communication system is much
efficient.

IV. TESTING AND RESULTS

The accuracy of Smart Energy Meter is checked by comparing
the readings that are displayed on the LCD of SEM and that
are received by SMS. Smart Energy Meter is also checked by
connecting and disconnecting the customers connection. We
connected different loads 100W, 200W, and 1000W and
checked its performance.

Figure 5: Smart Energy Meter in working

conditions, power factor calculation, less operation cost and

removal of possible corruption related to meter reading.
VI. FUTURE RECOMMENDATIONS
I thought there are few possibilities which can also be done on
this project in future as I have provided flexibility in the
project especially in controller section. The future research
should include the proper methodology for measuring the
power factor of the load.
Recommendations for future are as follows:
Instead of GSM networks, some other means of
communication should be used.
In case of GSM, there must be security of GSM so
that it cant be hacked.
Power factor must be measured by different
techniques.
Linking of the data received by GSM to computer and
developing a program which incorporates the tariff
related to specific consumer and calculating the bill
directly on the computer. In this way the computer
will calculate the bill directly using the data received
through GSM network.
Smart energy Meter can be modified for the detection
of illegal use of electricity.
ACKNOWLEDGEMENT
The authors would like to thank Prof. Dr. Muhammad Ahmad
Chaudhary, whose guidance and support from the initial to the
final level enabled us to develop an understanding of the
subject. On a more personal note we would like to thank Rana
M. Shahid Iqbal for supporting us, encouraging us and making
us realise that there is a whole world outside our research.
Lastly, we offer our regards and blessings to all of those who
supported us in any respect during the completion of the
project.

Figure 6: The internal circuitry of Smart Energy Meter.

REFERENCES
The testing of SEM provided accurate results, hence verifying
the performance and accuracy of the system.
V. CONCLUSION
The paper describes the design and working of Smart
Energy Meter and represents how Smart Energy Meter can be
used for Automatic Meter Reading. It is the most economical
implementation to develop mankind in this era of technology.
With the present enhancement in the use of technology to
facilitate mankind, it is an efficient and practical utilization of
present networks. This paper also shows that how customer
can manage the load by using Smart Energy Meter. It provides
ease in taking the meter readings, accuracy, detection of faulty

[1] Vinu V Das, Wireless Communication System for Energy Meter

Reading International Conference on Advances in Recent Technologies in
Communication and Computing 2009.
[2] Ashna.k , Sudhish N George. GSM Based Automatic Energy Meter
Reading System with Instant Billing 978-1-4673-5090-72013 IEEE
[3] Liting Cao, Jingwen Tian and Dahang Zhang Networked Remote MeterReading System Based on Wireless Communication Technology IEEE
International Conference on Information Acquisition, August 20 - 23, 2006,
Weihai, Shandong, China
[4]A. Arif , Muhannad AI-Hussain, Nawaf AI-Mutairi, Experimental Study
and Design of Smart Energy Meter for the Smart Grid 978-1-4673-637472013 IEEE
[5] Ashna.k ,Sudhish N George. GSM Based Automatic Energy Meter
Reading System with Instant Billing 978-1-4673-5090-72013 IEEE.
[6] Adnan Rashdi, R. Malik, S. Rashid, A. Ajmal, S. Sadiq , Remote Energy
Monitoring, Profiling and Control Through GSM Network, International
Conference on Innovations in Information Technology (IIT) 2012.

[7] Smart meter Implementation Strategy Prospectus. July 2010. DECC,

Ofgem/Ofgem E-Serve.
[8] T. Chandler, The technology development of automatic metering and
monitoring systems, in IEEE International Power Eng. Conf., Dec. 2005.
[9] G. T. Heydt, Virtual surrounding face geocasting in wireless ad hoc and
sensor networks, Electric Power Quality: A Tutorial Introduction, vol. 11,
no. 1, pp. 1519, Jan. 1998.
[10] M. Faisal and A. Mohamed, A new technique for power quality based
condition monitoring, in 17th Conf. Electrical Power Supply Industry,
Oct. 2008.
[11] P. RakeshMalhotra, Dr.R.Seethalakshmi Automatic Meter Reading and
Theft Control System by Using GSM P.RakeshMalhotra et al. /
International Journal of Engineering and Technology (IJET).
[12] H. Tan, H. Lee, , and V. Mok, Automatic power meter reading system
using GSM network, in IEEE International Power Eng. Conf., Dec. 2007.
[13] J. Surrat, Integration of cebus with utility load management and
automatic meter reading, in IEEE Trans. Consumer Electron., vol. 37,no. 3,
Aug. 1991, pp. 406412.
[14] A. Abdollahi, M. Dehghani, and N. Zamanzadeh, SMS-based
reconfigurable automatic meter reading system, in IEEE International Conf.
Control Appl., Oct. 2007.
[15] Tarek Khalifa, Kshirasagar Naik and Amiya Nayak A Survey of
Communication Protocols for Automatic Meter Reading Applications in
IEEE Communications Surveys & Tutorials, vol. 13, no. 2, second quarter
2011.
[16] Ali Abdollahi, Marjan Dehghani, and Negar Zamanzadeh SMS-based
Reconfigurable Automatic Meter Reading System in16th IEEE International
Conference on Control Applications. Part of IEEE Multi-conference on
Systems and Control Singapore, 1-3 October 2007
[17] Terry Chandler The Technology Development of Automatic Metering
and Monitoring Systems, The 7th International Power Engineering
Conference, pp. 147-150, Nov. 2005.
[18] Ingeoborg Graabak, Ove S. Grande, Jussi Ikaheimo and Seppo
Karkkainen, Establishment of Automatic Meter Reading and Load
Management Experiences and Cost/Benefit 2004 International Conference
on Power System Technology, pp. 1333-1338 Nov. 2004.
[19] A Minosi, A Martinola, S. Mankan, F. Balzarini, A. N. Kostadinov, M.
Prevostini, Intelligent, Low Power Cost Measurement System for Energy
Consumption, International Symposium on Virtual Environment, HumanComputer Interfaces and Measurement Systems, pp. 125-130, Jul. 2003.
[20] Albert Treyl, Thilo Sauter, and Gerd Bumiller, Real- Time Energy
Management over Power Lines and Internet, The Proceeding of the 8th
International Symposium on Power Line Communications and its
Applications, pp. 306-311, 2004.
[21] R. Tahboub, V. Lazarescu, Novel Approach for Remote Energy
Metering Reading using Mobile Agents, 3rd International Conference on
Information Technology, New Generation, pp. 84-90, Apr. 2006.
[22] B. S. Koay, S.S. Cheah, Y.H.Sng, P.H.J. Chong, P. Shum, Y.C.Tong,
X.Y.Wang, Y. X. Zuo and H. W. Kuek, Design and Implementation of
Bluetooth Energy Meter, Proceeding of the 2003 Joint Conference of the 4 th
International Conference on Information, Communications and Signal
Processing, 2003 Pacific Rim Conference on Multimedia, pp. 1474-1477,
Dec. 2003
[23] Mohd Yunus Nayan, Aryo Handoko Primicanta, Mohammad Awan
Hybrid Automatic Meter Reading System in IEEE International
Conference on Computer Technology and Development 978-0-7695-3892-1/
2009.
[24] Yujun Bao and Xiaoyan Jiang, Design of electric Energy Meter for
long-distance data information transfers which based upon GPRS, ISA 2009.
International Workshop on Intelligent Systems and Applications,2009.
[25] H.G.Rodney Tan,C.H. Lee,V.H.Mok,Automatic power meter reading
system using GSM network, The 8 Conference (IPEC 2007).
[26] Vivek Kumar Sehgal,Nitesh Panda, Nipun Rai Handa, Electronic
Energy Meter with instant billing,UKSim Fourth European Modelling
Symposium on Computer Modelling and Simulation.
[27] Bharath P, Ananth N, Vijetha S, Jyothi Prakash K. V. ,Wireless
automated digital Energy Meter, ICSET 2008.
[28] P.K. Lee and L.L. Lai, Fieee, A practical approach to wireless GPRS
on-line power quality monitoring system, Power Engineering Society
General Meeting, 2007.

[29] Subhashis Maitra, Embedded Energy Meter- A new concept to measure

the energy consumed by a consumer and to pay the bill, Power System
Technology and IEEE Power India Conference, 2008.
[30] T El-Djazairy, B J Beggs and I F Stewart, Investigation of the use of
the Global System for Mobile Communications (GSM) network for metering
and load management telemetry, Electricity Distribution. Part 1:
Contributions. CIRED. 14th International Conference and Exhibition on
(IEE Conf. Publ. No. 438).
[31] Li Kaicheng, Liu Jianfeng, Yue Congyuan, Zhang Ming. Remote power
management and meter-reading system based on ARM microprocessor,
Precision Electromagnetic measurements Digest, 2008. CPEM 2008.
Conference on Digital Object Identifier.
[32] S. Kerk, An AMR study in an Indian utility, in IEEE Power
Eng.Conf., Dec. 2005.
[33] S. Soh and S. Kerk, The electricity and metering trends in Singapore,
in IEEE Power Eng. Conf., Dec 2005.
[34]Adnan Rashdi, R. Malik, S. Rashid, A. Ajmal, S. Sadiq , Remote Energy
Monitoring, Profiling and ControlThrough GSM Network , International
Conference on Innovations in Information Technology (IIT) 2012.

BIOGRAPHIES OF AUTHORS:

H. M. Zahid Iqbal received the

Bachelors degree in Electrical
Engineering from the University of
Engineering & Technology Taxila,
Pakistan in 2013.
He is currently working as Research
Assistant at University of Engineering
& Technology Taxila, Pakistan.

M. Waseem received the Bachelors

degree in Electrical Engineering from
the University of Engineering &
Technology Taxila, Pakistan in 2012.
He is currently working as Lab.
Engineer at University of Engineering
& Technology Taxila, Pakistan.