https://www.captiveaire.

com/MANUALS/AIRSYSTEMDESIGN/DESIGNAIRSYST
EMS.HTM

Designing Air Flow Systems

A theoretical and practical guide to the basics of designing air flow systems.

1.

Air Flow
1.1. Types of Flow
1.2. Types of Pressure Losses or Resistance to Flow
1.3. Total Pressure, Velocity Pressure, and Static Pressure

2.

Air Systems
2.1. Fan Laws
2.2. Air Density
2.3. System Constant

3.

Pressure Losses of an Air System

3.1. Sections in Series
3.2. Sections in Parallel
3.3. System Effect

4.

Fan Performance Specification

4.1. Fan Total Pressure
4.2. Fan Static Pressure

5.

Pressure Calculations
5.1. Methodology
5.2. Assumptions and Corrections

6.

Problem # 1 An Exhaust System

7.

Problem # 2 A Change to the Systems Air Flow Rate

8.

Problem # 3 A Supply System

9.

Appendix 1 Equations

10. Appendix 2 ASHRAE Fittings

11. Appendix 3 Bullhead Tee Curves

Designing Air Flow Systems

1. Air Flow
Flow of air or any other fluid is caused by a pressure differential between two points. Flow will originate from an area of
high energy, or pressure, and proceed to area(s) of lower energy or pressure.

P1

FLOW

P0

P1>P0
Duct air moves according to three fundamental laws of physics: conservation of mass, conservation of energy, and
conservation of momentum.
Conservation of mass simply states that an air mass is neither created nor destroyed. From this principle it
follows that the amount of air mass coming into a junction in a ductwork system is equal to the amount of air mass
leaving the junction, or the sum of air masses at each junction is equal to zero. In most cases the air in a duct is
assumed to be incompressible, an assumption that overlooks the change of air density that occurs as a result of
pressure loss and flow in the ductwork. In ductwork, the law of conservation of mass means a duct size can be
recalculated for a new air velocity using the simple equation:
V2 = (V1 * A1)/A2
Where V is velocity and A is Area
The law of energy conservation states that energy cannot disappear; it is only converted from one form to
another. This is the basis of one of the main expression of aerodynamics, the Bernoulli equation. Bernoulli's
equation in its simple form shows that, for an elemental flow stream, the difference in total pressures between any
two points in a duct is equal to the pressure loss between these points, or:
(Pressure loss)1-2 = (Total pressure)1 - (Total pressure)2
Conservation of momentum is based on Newton's law that a body will maintain its state of rest or uniform motion
unless compelled by another force to change that state. This law is useful to explain flow behavior in a duct
system's fitting.

1.1. Types of Flow

Laminar Flow
Flow parallel to a boundary layer. In HVAC system the plenum is a duct.
Turbulent Flow
Flow which is perpendicular and near the center of the duct and parallel near the outer edges of the duct.
Most HVAC applications fall in the transition range between laminar and turbulent flow.

Page 2

Designing Air Flow Systems

1.2. Types of Pressure Losses or Resistance to Flow

Pressure loss is the loss of total pressure in a duct or fitting. There are three important observations that describe
the benefits of using total pressure for duct calculation and testing rather than using only static pressure.

Only total pressure in ductwork always drops in the direction of flow. Static or dynamic pressures alone do not
follow this rule.

The measurement of the energy level in an air stream is uniquely represented by total pressure only. The
pressure losses in a duct are represented by the combined potential and kinetic energy transformation, i.e., the
loss of total pressure.

The fan energy increases both static and dynamic pressure. Fan ratings based only on static pressure are
partial, but commonly used.

Pressure loss in ductwork has three components, frictional losses along duct walls and dynamic losses in fittings
and component losses in duct-mounted equipment.
Component Pressure
Due to physical items with known pressure drops, such as hoods, filters, louvers or dampers.
Dynamic Pressure
Dynamic losses are the result of changes in direction and velocity of air flow. Dynamic losses occur whenever an air
stream makes turns, diverges, converges, narrows, widens, enters, exits, or passes dampers, gates, orifices, coils,
filters, or sound attenuators. Velocity profiles are reorganized at these places by the development of vortexes that
cause the transformation of mechanical energy into heat. The disturbance of the velocity profile starts at some
distance before the air reaches a fitting. The straightening of a flow stream ends some distance after the air passes
the fitting. This distance is usually assumed to be no shorter then six duct diameters for a straight duct. Dynamic
losses are proportional to dynamic pressure and can be calculated using the equation:
Dynamic loss = (Local loss coefficient) * (Dynamic pressure)
where the Local loss coefficient, known as a C-coefficient, represents flow disturbances for particular fittings or for
duct-mounted equipment as a function of their type and ratio of dimensions. Coefficients can be found in the
ASHRAE Fittings diagrams.
A local loss coefficient can be related to different velocities; it is important to know which part of the velocity profile
is relevant. The relevant part of the velocity profile is usually the highest velocity in a narrow part of a fitting cross
section or a straight/branch section in a junction.
Frictional Pressure
Frictional losses in duct sections are result from air viscosity and momentum exchange among particles moving
with different velocities. These losses also contribute negligible losses or gains in air systems unless there are
extremely long duct runs or there are significant sections using flex duct.
The easiest way of defining frictional loss per unit length is by using the Friction Chart (ASHRAE, 1997); however,
this chart (shown below) should be used for elevations no higher of 500 m (1,600 ft), air temperature between 5C
and 40C (40F and 100F), and ducts with smooth surfaces. The Darcy-Weisbach Equation should be used for
non-standard duct type such as flex duct.

Page 3

Designing Air Flow Systems

Friction Chart (ASHRAE HANDBOOK, 1997)

Page 4

Designing Air Flow Systems

1.3. Total Pressure, Velocity Pressure, and Static Pressure

It is convenient to calculate pressures in ducts using as a base an atmospheric pressure of zero. Mostly positive
pressures occur in supply ducts and negative pressures occur in exhaust/return ducts; however, there are cases
when negative pressures occur in a supply duct as a result of fitting effects.
Airflow through a duct system creates three types of pressures: static, dynamic (velocity), and total. Each of these
pressures can be measured. Air conveyed by a duct system imposes both static and dynamic (velocity) pressures
on the duct's structure. The static pressure is responsible for much of the force on the duct walls. However, dynamic
(velocity) pressure introduces a rapidly pulsating load.
Static pressure
Static pressure is the measure of the potential energy of a unit of air in the particular cross section of a duct. Air
pressure on the duct wall is considered static. Imagine a fan blowing into a completely closed duct; it will create
only static pressure because there is no air flow through the duct. A balloon blown up with air is a similar case in
which there is only static pressure.
Dynamic (velocity) pressure
Dynamic pressure is the kinetic energy of a unit of air flow in an air stream. Dynamic pressure is a function of both
air velocity and density:
Dynamic pressure = (Density) * (Velocity) 2 / 2
The static and dynamic pressures are mutually convertible; the magnitude of each is dependent on the local duct
cross section, which determines the flow velocity.
Total Pressure
Consists of the pressure the air exerts in the direction of flow (Velocity Pressure) plus the pressure air exerts
perpendicular to the plenum or container through which the air moves. In other words:
PT = P V + P S
PT = Total Pressure
PV = Velocity Pressure
PS = Static Pressure
This general rule is used to derive what is called the Fan Total Pressure. See the section entitled Fan Performance
Specifications for a definition of Fan Total Pressure and Fan Static Pressure.

Page 5

Designing Air Flow Systems

2. Air Systems
For kitchen ventilation applications an air system consists of hood(s), duct work, and fan(s). The relationship between
the air flow rate (CFM) and the pressure of an air system is expressed as an increasing exponential function. The graph
below shows an example of a system curve. This curve shows the relationship between the air flow rate and the
pressure of an air system.

Complex systems with

branches and junctions, duct
size changes, and other variations can be broken into sections or sub-systems. Each section or sub-system has its own
system curve. See the diagram below for an illustration of this concept.

Page 6

Designing Air Flow Systems

2.1. Fan Laws

Use the Fan Laws along a system curve. If you know one (CFM, S.P.) point of a system you could use Fan Law 2 to
determine the static pressure for other flow rates. They apply to a fixed air system. Once any element of the system
changes, duct size, hood length, riser size, etc.. the system curve changes.
CFM x
RPM x
------- = ------CFM known RPM known

Fan Law 1

SP x
CFM2 x
RPM2x
------ = ------- = ------SP known CFM2known RPM2known

Fan Law 2

BHPx
CFM3x
RPM3x
------ = ------- =
------BHPknown CFM3known RPM3known

Fan Law 3

Other calculations can be utilized to maneuver around a fan performance curve. For example, to calculate BHP from
motor amp draw, use the following formula:
1 phase motors
BHP = V * I * E * PF
746

3 phase motors
BHP = V * I * E * PF * 1.73
746

where:
BHP = Brake Horsepower
V = Line Voltage
I = Line Current
E = Motor Efficiency (Usually about .85 to .9)
PF = Motor Power Factor (Usually about .9)
Once the BHP is known, the RPM of the fan can be measured. The motor BHP and fan RPM can then be matched on
the fan performance curve to approximate airflow.

2.2. Air Density

The most common influences on air density are the effects of temperature other than 70 F and barometric
pressures other than 29.92 caused by elevations above sea level.
Ratings found in fan performance tables and curves are based on standard air. Standard air is defined as clean,
dry air with a density of 0.075 pounds per cubic foot, with the barometric pressure at sea level of 29.92 inches of
mercury and a temperature of 70 F. Selecting a fan to operate at conditions other then standard air requires
adjustment to both static pressure and brake horsepower. The volume of air will not be affected in a given system
because a fan will move the same amount of air regardless of the air density. In other words, if a fan will move
3,000 cfm at 70 F it will also move 3,000 CFM at 250 F. Since 250 F air weighs only 34% of 70F air, the fan will
require less BHP but it will also create less pressure than specified.
When a fan is specified for a given CFM and static pressure at conditions other than standard, the correction
factors (shown in table below) must be applied in order to select the proper size fan, fan speed and BHP to meet the
new condition.
The best way to understand how the correction factors are used is to work out several examples. Lets look at an
example using a specification for a fan to operate at 600F at sea level. This example will clearly show that the fan
must be selected to handle a much greater static pressure than specified.
Example #1: A 20 centrifugal fan is required to deliver 5,000 cfm at 3.0 inches static pressure.
Elevation is 0 (sea level). Temperature is 600F. At standard conditions, the fan will require 6.76
bhp
Page 7

Designing Air Flow Systems

1. Using the chart below, the correction factor is 2.00.
2.
Multiply the specified operating static pressure by the correction factor to determine the
standard air density equivalent static pressure. (Corrected static pressure = 3.0 x 2.00 =
6. The fan must be selected for 6 inches of static pressure.)
3.
Based upon the performance table for a 20 fan at 5,000 cfm at 6 inches wg, 2,018 rpm is
needed to produce the required performance.
4. What is the operating bhp at 600 F?
Since the horsepower shown in the performance chart refers to standard air density, this should
be corrected to reflect actual bhp at the lighter operating air.
Operating bhp = standard bhp 2.00 or 6.76 2.00 = 3.38 bhp.

2.3. System Constant

Every air system or sub-system has a system constant. This constant can be calculated as long as you know one (CFM,
Static Pressure) point. You use a variation of the fan laws to calculate the system constant. To calculate the system
constant:
K system = S.P./(CFM)2
Once you have the system constant you can calculate the static pressure for any flow rate.
S.P. = (CFM)2 * K system

Page 8

Designing Air Flow Systems

3. Pressure Losses of an Air System

Pressure losses are more easily determined by breaking an air system into sections. Sections can be in series or in
parallel.

3.1. Sections in Series

For sections or components in series simply sum up all the sections. A single duct that has the same shape, cross
section, and mass flow is called a duct section or just a section.
Following is the recommended procedure for calculating total pressure loss in a single duct section:

Gather input data: air flow, duct shape, duct size, roughness, altitude, air temperature, and fittings;

Calculate air velocity as a function of air flow and cross section;

Calculate local C-coefficients for each fitting used; and

Calculate pressure loss using the friction chart

The following is a simple example of how duct pressure accumulates and is totaled in a section.

3.2. Sections in Parallel

When designing sections that are parallel it is important to remember that the branches of a junction all have the
same total pressure. This is a fact. It is governed by a principle which states that areas of high energy move to
areas of lower energy. We will see how this applies to air systems in parallel.
To illustrate these concepts we will reference the diagram below. In this example we calculate the pressure losses for
Section 1 to be -0.75 at the junction. We calculate the pressure losses for Section 2 to be -0.6 at the junction. (NOTE:
For simplicitys sake we do not consider the pressure loss incurred by the junction.) These would be the actual pressure
losses of the system were they operating independently; however, they do not. They interact at the junction. This means
that whenever air flow encounters a junction it will take the path of least resistance and the total pressure losses of each
branch of the junction will be the same.
For sections that run parallel, always use the section with the higher pressure loss/gain to determine pressure
losses/gains through a system. Adjust the branch with the lower pressure loss/gain by increasing the flow rate or
decreasing the duct size to increase the pressure loss to that of the higher branch.

Page 9

Designing Air Flow Systems

If the flow rate or the duct size is not changed the air flow through each branch will adjust itself so that each branch has
the same total pressure loss/gain. In other words, more air flows through the branch with the lower pressure loss/gain or
energy state.
In the example below, the actual pressure loss would be somewhere between -0.75 and -0.6. Section 1 would pull less
than 2000 CFM and Section 2 would pull more than 1800 CFM.

3.3. System

Effect

System Effect occurs

in an air system when
two or more elements such as fittings, a hood and a fitting, or a fan and a fitting occur within close proximity to one
another. The effect is to increase the energy or pressure in a system as air flows through the elements. To calculate the
pressure loss incurred by such a configuration, consider two elements at a time. For example, if two elbows occur 4 feet
from one another this configuration will have a pressure loss associated with it.
Calculate the pressure loss/gain associated with each fitting as if it occurs alone. Sum these and multiply them by a
system effect coefficient (K). The system effect coefficient can be obtained from the ASHRAE Fitting Diagrams for only a
limited number of configurations of elements.
Configurations not listed must use estimates or best guesses. In many cases, you can use a listed configuration as a
guide.
One configuration not listed is an elbow within close proximity to the collar of a hood. As a rule of thumb, the chart
below can offer some guidance for determining the system effect for this situation. Remember the coefficients in the chart
are only an estimate.
System Effect Table
Distance between Riser and
Elbow
2 feet
3 feet
4 feet
5 feet

System Effect Coefficient (K)

1.75
1.5
1.3
1.2

Page 10

Designing Air Flow Systems

The diagrams below show system effect factors for straight through elements and turning elements. For rectangular
ductwork, D = (2HW)/(H+W). The following formula should be used to calculate the pressure caused by system effect:

Pressure Loss = K * (Element A Resistance + Element B Resistance)

Straight Through Flow

Turning Elements

The following diagrams show proper and improper methods of constructing ductwork:

Page 11

Designing Air Flow Systems

4. Fan Performance Specification

A fan performance spec is given as a Fan Total Pressure or a Fan Static Pressure which can handle a certain flow
rate. Most manufacturers' performance charts are based on Fan Static Pressure.

4.1. Fan Total Pressure

Fan total Pressure is the pressure differential between the inlet and the outlet of the fan. It can be expressed in these
terms:
P t fan = P

t loss

+ P v system outlet + (P

s system outlet

+ P s system entry + P v system entry)

P t fan = Fan Total Pressure

P t loss = Dynamic, Component, and Frictional Pressure through the air system.
P s system outlet = Static Pressure at System Outlet
P s system entry = Static Pressure at System Entry
P v system entry = Velocity Pressure at System Entry
P v system outlet = Velocity Pressure at System Outlet
For most HVAC applications: (P s outlet + P s entry + P
Therefore: P t fan = P t loss + P

) =0

v entry

v system outlet

4.2. Fan Static Pressure

The Fan Static Pressure is expressed as the Fan Total Pressure minus the velocity pressure at the fan discharge, or:

P s fan = P t loss + P v system

outlet

- P v discharge

Where P v discharge = Velocity Pressure at the Fan Discharge.

For Exhaust Systems with resistance only on the inlet side, the fan static pressure is:

P s fan = P t loss
For exhaust system: P v system outlet = P v discharge
For Supply Systems with resistance on the outlet side, the fan static pressure is:

P s fan = P t loss - P v discharge

P v system outlet can be assumed to be 0.
The diagram below illustrates the difference between exhaust and supply systems.

Page 12

Designing Air Flow Systems

5. Pressure Calculations
5.1. Methodology
Break the system into sections.
A new section occurs at:
1) Changes in duct size.
2) Change in air volume
Calculate losses for each section.
Begin at the section farthest from the fan and work towards the fan. For each section:
1.

Write down or calculate all known variables.

Air Flow Rate. (Q)
Duct Cross-Sectional Area of the section. (A)
Center-Line Length of the section. (L)
Air Velocity through the section. (V=Q/A)
Velocity Pressure. (Pv = (V/4005) 2)

2.

Write down or calculate all pressure losses in the section.

a) List the Component Losses/Gains.
Incurred by hoods, ESPs, filters, dampers, etc..
b) Calculate the Dynamic Losses/Gains.
Occur through elbows, transitions, tees, or any other type of fitting.
Use the ASHRAE Fitting Diagrams to find Dynamic Loss Coefficients for fittings.
Be sure to factor in System Effect!
c) Calculate Frictional Losses/Gains.
Use the ASHRAE Friction Chart for standard galvanized ductwork.
Use the Darcy-Weisbach Equation for non-standard duct such as flex duct.

3.

Sum up the Component, Dynamic, and Frictional Pressure for the section.

4.

Sum up the pressure losses for all of the sections.

5.2. Assumptions and Corrections

Standard Air Density, .075 lb/cu ft, is used for most HVAC applications.
Frictional losses based on galvanized metal duct with 40 joints per 100 ft.
Correction for "Non-Standard" Duct Material
If material other than galvanized metal is used in parts of the system, you will have to adjust for the difference
in the material's roughness factor. This means the Friction Chart typically used to determine frictional losses
cannot be used and you must use a variation of the Darcy-Weisbach Equation. See the section titled
Equations for more information on this equation.
Correction for Density
Not needed if the temperature is between 40 F to 100 F and elevations are between 1000 ft to 1000 ft.
Correction for Moisture
Not needed if air temperature < 100 F.

Page 13

Designing Air Flow Systems

6. Problem # 1 An Exhaust System

The first step is to break the system into sections.

Section 1 runs from the 16 Hood to the Bullhead Tee.
Section 2 runs from the 13 Hood to the Bullhead Tee.
Section 3 runs from the Bullhead Tee to the Exhaust Fan.
Now calculate the pressure losses for each section.

Section 1
Air Flow Rate Q = 4000 cfm
Cross-Sectional Area A = 10 x 36/144 = 2.5 ft2
Center Line Distance L = 2 + 6 = 8
Velocity V = 4000/2.5 = 1600 ft/min
Velocity Pressure = Pv1 = (V/4005)2 = (1600/4005) 2 = 0.16

Loss Calculations
Component Losses
Hood Loss
Phood1 = -0.688
Look up from manufacturer hood static pressure curves. Here is a link to the Hood Static Pressure Calculator.
Frictional Losses
Use the Friction Chart to look up the pressure loss per 100 ft of duct.
Pfr1 = -(.16/100 ft) * (8) = -0.013
Dynamic Losses
Mitered Elbow. Look up Fitting 3-6 in Appendix 2 - ASHRAE Fittings. The dynamic coefficient C0 = 1.3
Pelbow1 = - Pv1 = -(1.3)*(0.16) = -0.208
Bullhead Tee. Look up coefficient from Appendix 3 - Bullhead Tee Curves.
Page 14

Designing Air Flow Systems

Some general rules for bullhead tees:

Since Section 1 has a larger duct size, this section is the u side of the bullhead tee. The following describes
how to use the bullhead tee curves to find Ku for the u side of the bullhead tee.
Since AU /AD = (10x36)/(20x30) = .6, we find the bullhead tee curves for which AU /AD is .6 and the y-axis
represents KU.
We know that Qb /Q D = 4000/(4000+3400) = .54. For simplicity and ease of graphing, we round .54 to the
nearest 10th giving us .5.
We also know that Ab /AD = (10x30)/(20x30) = .5.
Equipped with these ratios, can draw a line from the point on the x-axis where Q b /Q D is .5 up to where it
intersects the curve for which Ab /AD is .5
We find Ku = 1.6
NOTE: Due to human error resulting from manually graphing the value of KU , the number you graph may be
slightly different than the value show above. The important thing is to know how to use the curves and get a
reasonable value for KU.
Now we can calculate the pressure drop contributed by the bullhead tee for Section 1:
Pbulltee1 = -Ku * Pv1 = -(1.6)*(0.16) = -0.256
The total pressure loss for Section 1 is:
P t loss 1 = Phood1 + Pfr1 + Pelbow1 + Pbulltee1
P t loss 1 = -0.688 -0.013 -0.208 -0.256 = -1.165

Section 2
Air Flow Rate Q = 3400 cfm
Cross-Sectional Area A = 10 x 30/144 = 2.1 ft2
Center Line Distance L = 2 + 7 = 9
Velocity V = 3400/2.1 = 1619 ft/min
Velocity Pressure = Pv2 = (V/4005) 2 = (1619/4005) 2 = 0.16

Loss Calculations
Component Losses
Hood Loss
Phood2 = -0.688

Look up from hood static pressure curves.

Frictional Losses
Use the Friction Chart to look up the pressure loss per 100 ft of duct.
Pfr2 = -(.18/100 ft) * (9) = -0.016
Dynamic Losses
Mitered Elbow. Look up Fitting 3-6 in Appendix 2 - ASHRAE Fittings.
The dynamic coefficient C0 = 1.3
Pelbow2 = - Pv2 = -(1.3)*(0.16) = -0.208
Bullhead Tee. Using the methodology described for the bullhead tee in Section 1, we can find the value of the
coefficient, Kb, for the b side of the bullhead tee. Use the bullhead tee curves for which AU /AD is .6 and the yaxis represents Kb.
We find that Kb = 1.75 and the resulting pressure loss is:
Pbulltee 2 = -Kb * Pv2 = -(1.75)*(0.16) = -0.280
Page 15

Designing Air Flow Systems

The total pressure loss for Section 2 is:
P t loss 2 = Phood2 + Pfr2 + Pelbow2 + Pbulltee2
P t loss 2 = -0.688 -0.016 -0.208 -0.280 = -1.192

Balance by Design
Note that the pressure loss of Section 2 is greater than the loss of Section 1. To balance the system by design
increase the air flow rate in Section 1 to bring it up to the higher pressure loss of Section 2.
To correct the air flow rate for Section 1 use the Fan Laws:
Q 1 new = Q 1 old * (P t loss 1 new / P t loss 1 old)1/2
Q 1 new = 4000 * (1.192/1.165) 1/2 = 4046 cfm

Section 3
Air Flow Rate Q = 3400 cfm + 4046 cfm = 7446 cfm
Cross-Sectional Area A = 20 x 30/144 = 4.17 ft2
Center Line Distance L = 9
Velocity V = 7446/4.17 = 1785 ft/min
Velocity Pressure = Pv3 = (V/4005) 2 = (1785/4005) 2 = .20

Loss Calculations
Component Losses
None
Frictional Losses
Use the Friction Chart to look up the pressure loss per 100 ft of duct.
Pfr2 = -(.15/100 ft) * (9) = -0.014
Dynamic Losses
None
Total pressure loss for Section 3 is:
P t loss 3 = Pfr3
P t loss 3 = -0.014

Total Pressure Loss of System

Since the pressure loss of Section 2 is greater than that of Section 1, it is used to calculate the pressure loss of
the entire system as shown below:
P t loss = P t loss 2 + P t loss 3 = -1.192 -0.014 = -1.206

Page 16

Designing Air Flow Systems

7. Problem # 2 A Change in the Systems Air Flow Rate

Now we will change the air flow rate through Section 2 from 3400 CFM to 3000 CFM. We will illustrate how once you
know one (CFM, S.P.) point of a system you can use the Fan Laws to calculate the pressure loss for other air flow rates.

Section 1
There is no change.

P t loss 1 = -1.165

Section 2
Air Flow Rate Q = 3000 CFM
Cross-Sectional Area A = 10 x 30/144 = 2.1 ft2
Center Line Distance L = 2 + 7 = 9
Velocity V = 3000/2.1 = 1429 ft/min
Velocity Pressure = Pv2 = (V/4005) 2 = (1429/4005) 2 = 0.13

Loss Calculations
Component Losses
Hood Loss. Use the Fan Laws to calculate a new Hood Loss or look it up in the Hood S.P. chart.
Phood2 = -(0.688)*((3000 CFM)2/(3400 CFM)2)
Phood2 = -0.536
Frictional Losses
Use the Friction Chart to look up the pressure loss per 100 ft of duct.
Pfr2 = -(.15/100 ft) * (9) = -0.014
Dynamic Losses
Mitered Elbow. Look up Fitting 3-6 in Appendix 2 - ASHRAE Fittings.
The dynamic coefficient C0 = 1.3
Pelbow2 = - Pv2 = -(1.3)*(0.13) = -0.169
Bullhead Tee. Since Section 2 is the b side, we use the set of bullhead tee curves for which AU /AD is .6 and
the y-axis represents Kb.
We find that Kb = 1.65
Pbulltee 2 = -Kb * Pv2 = -(1.65)*(0.13) = -0.215
Total Section Loss:
P t loss 2 = Phood2 + Pfr2 + Pelbow2 + Pbulltee2
P t loss 2 = -0.536 -0.014 -0.169 -0.215 = -0.93

Using the Fan Laws to calculate the new total pressure loss for Section 2:
P t loss 2 = -(1.192)*((3000 CFM)2/(3400 CFM)2) = -0.93

Balance by Design
Note that the pressure loss of Section 1 is now greater than the loss of Section 2. To balance the system by
design we must increase the air flow rate in Section 2 to bring it up to the higher pressure loss of Section 1.
To correct the air flow rate for Section 2 use the Fan Laws:
Q 2 new = Q 2 old * (P t loss 2 new / P t loss 2 old)1/2
Q 2 new = 3000 * (1.165/0.93) 1/2 = 3357 CFM

Section 3
Page 17

Designing Air Flow Systems

Air Flow Rate Q = 3357 CFM + 4000 CFM = 7357 CFM
Cross-Sectional Area A = 20 x 30/144 = 4.17 ft2
Center Line Distance L = 9
Velocity V = 7357/4.17 = 1764 ft/min
Velocity Pressure = Pv3 = (V/4005) 2 = (1764/4005) 2 = 0.19

Loss Calculations
Component Losses
None
Frictional Losses
Use the Friction Chart to look up the pressure loss per 100 ft of duct.
Pfr2 = -(0.14/100 ft) * (9) = -0.013
Dynamic Losses
None

Using the Fan Laws to calculate the new total pressure loss for Section 3:
P t loss 3 = -(0.014)*((7357 cfm) 2/(7446 cfm) 2) = -0.013

Total System Loss

Calculated with Tables and ASHRAE Charts
P t loss = P t loss 1 + P t loss 3 = -1.165 -0.013 = -1.178
As shown above, Branch 1 of the junction is used to calculate the systems total pressure loss because it has
the greater pressure drop of the two branches.

Calculated with the Fan Laws

P t loss = -(1.206)*((7357 cfm) 2/(7446 cfm) 2) = -1.178

Page 18

Designing Air Flow Systems

8. Problem # 3 - A Supply System

The first part of the problem will show the pressure gains obtained from measuring the total pressure at 3 points shown in the
diagram above. It will provide some rules of thumb for estimating pressure for elbow and at the supply collar. The second
part of the problem will calculate the pressure gain of the system and compare it to the measured pressure gain.
The entire system satisfies the definition of a section since there are no junctions or duct size changes. The transitions off the
supply collars can be included in the section.

Supply System - Measured Pressure

A 0 to 1 Dwyer manometer was used to measure the pressure of the system at 3 points. The pressure was measured for
two different flow rates. The results are show in the table below.
Measurements Taken at 3 points of the Supply System
Air Flow
Velocity
Point 1
Point 2
Rate (CFM)
(ft/min)
@ collar (in. wg)
after 1st elbow
(in. wg)
1000
935
0.075
0.140
1920
1793
0.276
0.570

Point 3
after 2nd elbow
(in. wg)
0.260
0.910

The table shows:

1)
2)

How high air velocities greatly increase the pressure. When the air flow rate is raised to 1920 cfm, the
velocity through the duct about doubles and the pressure increases 3-1/2 fold.
The system effect of having 2 elbows close to each other and being close to the hood.
Using the pressure gains for 1000 cfm flowing through the system, we see that the pressure gain for the
first elbow is: 0.14 - 0.075 = 0.065. This reflects the system effect of having an elbow close to the
supply opening of a hood.
The pressure gain for the second elbow is: 0.26 - 0.14 = 0.12. This reflects the system effect of having
two elbows within close proximity to one another and being close to the hood.
Page 19

Designing Air Flow Systems

When the system supplies 1000 CFM, the pressure gain at the supply collar is 0.075. This illustrates
how low the pressure really is when a system is designed for the desired velocity between 900 and 1000
ft/min. The table below provides some rules of thumb when estimating pressure gain at the supply collar:

3)

Hood Length (L)

Pressure Loss Estimate
L <= 8
1/16 max.
8 < L <= 12
1/16 to 1/8 max.
12 < l <= 16
1/8 to 1/4 max.
This table assumes that the system has been designed for velocities around 1000 ft/min.

Test Kitchen Supply System - Calculated Pressure

Section 1
Air Flow Rate Q = 1000 cfm
Cross-Sectional Area A = r2 = (7)2/144 = 1.069 ft2
Center Line Distance L = 15
Velocity V = 1000/1.069= 935 ft/min
Velocity Pressure = Pv1 = (V/4005) 2 = (935/4005) 2 = 0.055

Loss Calculations
Component Losses
Hood. Assume 1/16 pressure gain at the collar.
P hood = 0.063
Frictional Losses
Use the Friction Chart to look up the pressure loss per 100 ft of duct.
Pfr = -(0.095/100 ft) * (15) = 0.014
Dynamic Losses
12x 20 to 10 x 16 Rectangular Transition
Use ASHRAE fitting 5-1 in Appendix 2 ASHRAE Fittings.
To find the dynamic coefficient we calculate:
/2 = tan -1(2/6) = 18o Therefore: = 36 o
A0 / A1 = (12x20)/(10x16) = 1.5
Therefore C0 = 0.05
P trans1 = C0Pv1 = (0.05)(0.055) = 0.003
10x 16 Rectangular to 14 Round Transition
Use ASHRAE fitting 4-6 in Appendix 2 ASHRAE Fittings.
B = W/H(A0 / A1 )2 = (16/10)(1.069/1.111)2 = 1.48
Re = 8.56DV = (8.56)(14)(935 ft/min) = 11205
Therefore Re x 10-4 = 11. Use the value for Re x 10-4 = 10
L/D is not relevant in this case.
C0 = 0.11
P trans2 = C0Pv1 = (0.11)(0.055) = 0.006
Two 90 Radius Elbows
Use ASHRAE fitting 3-2. Assume a 3 piece elbow.
Assume r = 10. So, r/D = 10/14 = .71 therefore K = 1.
C0 = 0.54
o

P elbow1 = C0Pv1 = (0.54)(0.055) = 0.03

P elbow2 = C0Pv1 = (0.54)(0.055) = 0.03

We must figure in the system effect incurred by having an elbow close to the supply collar. Use the table in the
System Effect section of this paper to estimate the system effect.
The elbow is about 2 above the supply riser to KSE = 1.75.
P SE elbow-hood = KSE P elbow1 = (1.75)(0.03) = 0.053
Page 20

Designing Air Flow Systems

Now we must factor in the system effect for the 2 elbows in succession. We decide to the S-Shaped fitting in the
ASHRAE handbook to estimate the system effect. We use ASHRAE fitting 3-14.
= 90 o
L/D = 60/14 = 4.29
K SE = 1.55
P SE S-fitting = K SE(P elbow1 + P elbow2) = 1.55(0.03 + 0.03) = 0.093
Total Section Loss:
P t loss 1 = Phood + Pfr + Ptrans1 + Ptrans2 + P SE elbow-hood + P SE S-fitting
P t loss 1 = 0.063 + 0.014 + 0.003 + 0.006 + 0.053 + 0.093
P t loss 1 = 0.232
The measured value of 0.26 differs because of error in the system effect estimates.
Now we can determine the size fan we need. A 10 blower will handle 1000 cfm at 0.232.
To calculate the Fan Static Pressure:
P s fan = P t loss - P v discharge
Use the blower manufacturer product literature to get the dimensions for the blower outlet so the velocity
pressure at the fan discharge can be calculated:
P v discharge = (V discharge/4005)2
P v discharge = ((1000/((11.38*13.13)/144))/4005) 2
P v discharge = 0.058
P s fan = 0.232 - 0.058 = 0.174

Page 21

Designing Air Flow Systems

9. Appendix 1 - Equations
Total Pressure (P T)
P T = P v+ P s
P v = Velocity Pressure
P s = Static Pressure

Fan Static Pressure (P s fan)

For Exhaust:
P s fan = P t loss
For Supply:
P s fan = P t loss - P v discharge
P s fan = Fan Static Pressure
P t loss = Dynamic and Friction Losses
P v discharge = Velocity Pressure at the Fan Discharge

Velocity Pressure (P v)
P v = (V/1097)2
For standard air P v equals:
P v = (V/4005) 2
V = Velocity through the duct.

Friction Losses (P fr)

Darcy-Weisbach Equation
P fr = (f / D) x L x VP
Then substitute (f / D) with H f:
P fr = Hf x L x VP
L = Duct Section Length (ft)
f = Friction Factor
D = Duct Diameter (ft)
H f is defined as:
H f = aVb / Qc
V = Velocity through the duct cross section.
Q = Flow Rate (cfm) through the duct section.
See Table titled Surface Roughness Correlation Constants to get values for a,b, and c.

Surface Roughness Correlation Constants

Material
k
Aluminum, Black Iron,
0.00015
Stainless Steel
Galvanized
0.0005
Flexible Duct
0.003
k = Roughness factor for the material.

A
0.0425

b
0.0465

c
0.602

0.0307
0.0311

0.533
0.604

0.612
0.639

Page 22

Designing Air Flow Systems

10. Appendix 2 ASHRAE Fittings

Fitting 3-2

Fitting 3-6

Page 23

Designing Air Flow Systems

Fitting 3-14

Page 24

Designing Air Flow Systems

Fitting 4-6

Fitting 5-1
Page 25

Designing Air Flow Systems

Page 26

Designing Air Flow Systems

11. Appendix 3 Bullhead Tee Curves

Au/Ad = 0.2, Kb

Au/Ad = 0.2, Ku
Page 27

Designing Air Flow Systems

Au/Ad = 0.3, Kb
Page 28

Designing Air Flow Systems

Au/Ad = 0.3, Ku
Page 29

Designing Air Flow Systems

Au/Ad = 0.4, Kb
Page 30

Designing Air Flow Systems

Au/Ad = 0.4, Ku
Page 31

Designing Air Flow Systems

Au/Ad = 0.5, Kb
Page 32

Designing Air Flow Systems

Au/Ad = 0.5, Ku
Page 33

Designing Air Flow Systems

Au/Ad = 0.6, Kb
Page 34

Designing Air Flow Systems

Au/Ad = 0.6, Ku
Page 35

Designing Air Flow Systems

Au/Ad = 0.8, Kb
Page 36

Designing Air Flow Systems

Au/Ad = 0.8, Ku
Page 37

Designing Air Flow Systems

Au/Ad = 1.0, Kb
Page 38

Designing Air Flow Systems

Au/Ad = 1.0, Ku
Page 39

Designing Air Flow Systems

Page 40