Scribd
Upload
84 views

Assignment#2: Applications of Thyristors in HVDC

The document discusses applications of thyristors in high voltage direct current (HVDC) transmission. It describes the structure and limitations of thyristors. It outlines several applications of thyristors including in high power thyristor valves for HVDC transmission, medium voltage drives, voltage source converters, mobile high voltage cable test systems, and pulse power applications such as food preservation and magnetic forming. Thyristors allow efficient long distance power transmission and control of medium to high voltage equipment.

Uploaded by

Rashid Altaf
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
84 views

Assignment#2: Applications of Thyristors in HVDC

The document discusses applications of thyristors in high voltage direct current (HVDC) transmission. It describes the structure and limitations of thyristors. It outlines several applications of thyristors including in high power thyristor valves for HVDC transmission, medium voltage drives, voltage source converters, mobile high voltage cable test systems, and pulse power applications such as food preservation and magnetic forming. Thyristors allow efficient long distance power transmission and control of medium to high voltage equipment.

Uploaded by

Rashid Altaf
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

ASSIGNMENT#2

APPLICATIONS OF THYRISTORS IN HVDC

SUBMITTED BY:

SUBMITTED TO:

GC RASHID ALTAF
EC-1315
DE-34-EE
SYN-A

MAM FAIZA NAWAZ

INTRODUCTION

GENERAL DESCRIPTION OF THYRISTOR:

High-power thyristors with direct light -triggering and integrated protection functions
can be utilized advantageously for applications in which several thyristors are connected in
series. This applies in particular to High -Voltage DC (HVDC) transmission, converters for
medium voltage drives, and also to certain pulse power applications.
STRUCTURE:
In 1960 the development of thyristors (also called SCRs = silicon controlled
rectifier) was started; since that time many development steps followed in order to
increase the power capability of the devices and to improve the reliability.
Power thyristors are manufactured from highly pure monocrystalline silicon. They
are so called NPNP semiconductors. This means that they consist of four layers which
are doped alternately with P and N. The outer, highly doped zones are the emitting
zones; the weakly doped, inner layers are the base zones. The control connection G is
located on the P base; J1-J3 designate the junctions between individual zones. The offstate voltage in the reverse direction is blocked at junction J1 between P-emitter and
N-base. The off-state voltage in the forward direction is blocked at junction J2 between Pbase and N-base.

LIMITATIONS OF THYRISTORS:
i) Thyristors are fast but not ideal switches. Several of the imperfections of the
thyristor in comparison with the ideal switch can be recognized in the static
V/I-characteristic of the thyristor. In the presence of off-state voltage, an offstate current (several mA) flows both in the forward direction and in the reverse
direction.
ii) Also a non-ideal static behavior of the thyristor is the on state voltage during
conduction. The entire voltage drop of an HVDC thyristor is of the order of two
to three volts. This means that for typical currents several kA, considerable power
losses must be dissipated.
iii) Limited di/dt-capability after turning on, as well as the reverse recovery
behavior including turn-off time has to be considered in the design of the powers
stack.
iv) There is a trend towards higher transmission current capability of long-distance
HVDC systems. With this trend, the requirements for higher current capabilities

arise. On the other hand, the blocking voltage of about 8kV per thyristor was
derived as an optimum of overall operational losses.

APPLICATIONS

HIGH POWER THYRISTOR VALVES:

Since the first commercial use of high voltage thyristor valves in HVDCtransmission systems in the early seventies, there has been a constant enhancement
of performance concerning the thyristors blocking as well as current carrying
capability. That improvement of the thyristor characteristics results in a drastic
decrease of components in a thyristor valve: to transmit the same amount of power
as in the beginning of the thyristor-era in HVDC-technique, only about 5% of the
thyristors (and snubber circuits) are necessary today. Despite the high blocking capability
of modern thyristors still a series connection of thyristors is necessary to compose a valve
with the required high voltage withstand capability.
The number of thyristors that have to be connected in series varies depending on
the application- between e.g. 10 thyristors per valve rated 8kV in a typical SVC
application and up to 120 thyristors in a typical HVDC valve in an 800Kv converter.

MEDIUM- VOLTAGE DRIVES:


Medium- voltage (MV) drives are getting more and more important, because of
their cost effective performance. Existing MV drive products range between 2.3 and 7.2
kV, tending to higher voltages of up to 15 kV. The main drives are mostly built with IGBT
modules in inverters with two or more levels. For high -end voltage and power systems,
Press Pack IGBTs and even LTTs (frequencies 50 -110 Hz) may be of interest because
direct series connection with redundancy of more than two semiconductors can be
accomplished in one level inverters. In soft starters, which work with full sine waves,
commutated thyristors can be used. In the upper voltage region where series connection
of semiconductors is necessary, the use of smaller LTTs (eupec T553N) is a big advantage.

VOLTAGE-SOURCE CONVERTERS (VSC):


Widely used in motor drives since the 1980s, voltage-source converters started to
appear in HVDC in 1997 with the experimental HellsjnGrngesberg project in Sweden.
By the end of 2011, this technology had captured a significant proportion of the HVDC
market.
The development of higher rated insulated-gate bipolar transistors (IGBTs), gate
turn-off thyristors (GTOs) and integrated gate-commutated thyristors (IGCTs), has made
smaller HVDC systems economical. The manufacturer ABB Group calls this
concept HVDC Light, while Siemens calls a similar concept HVDC PLUS (Power Link
Universal System) and Alstom call their product based upon this technology HVDC
MaxSine. They have extended the use of HVDC down to blocks as small as a few tens of
megawatts and lines as short as a few score kilometers of overhead line. There are several
different variants of VSC technology: most installations built until 2012 use pulse width

modulation in a circuit that is effectively an ultra-high-voltage motor drive. Current


installations, including HVDC PLUS and HVDC MaxSine, are based on variants of a
converter called a Modular Multi-Level Converter (MMC).
Multilevel converters have the advantage that they allow harmonic filtering equipment to
be reduced or eliminated altogether. By way of comparison, AC harmonic filters of typical
line-commutated converter stations cover nearly half of the converter station area.
With time, voltage-source converter systems will probably replace all installed simple
thyristors-based systems, including the highest DC power transmission applications.

MOBILE HIGH- VOLTAGE CABLE TEST SYSTEMS:


High- voltage network maintenance is necessary to ensure supply reliability.
Measurement and location of partial discharges is internationally accepted as an
indication of insulation system integrity. Such test systems are built like a resonant
circuit. When the LTTs are triggered they form together with the test object and an air
-cored inductor a series resonant circuit. High voltage cable insulation usually has a
relatively low dissipation factor.
Because it is easy to connect LTTs in series, the devices will be used in a mobile
high - voltage cable test system for 250 kV.

PULSE-POWER APPLICATIONS:
Because of the high dI/dt -capability, LTTs can be used in many pulse-power
applications such as preservation of liquid food, fast magnetic forming, crow bars and
high -power lasers. For such pulse-power applications the energy is normally stored in
capacitors that are discharged in one or several pulses with high dI/dt and peak current.
i) House hold Applications:
Preservation of liquid foods is achieved by high - voltage arc discharges. The
energy is stored in several capacitors. By triggering serially-connected LTTs, the voltage
pulse is transformed to a higher level to trigger the spark gap. There are three main
mechanisms that cause microbial inactivation during arc discharge treatment: Shock
waves, UV - radiation, and the formation of radicals. The advantages of this method are
its cost effectiveness and that the taste of the food is not modified by pasteurization. This
kind of applications normally works with a frequency of several ten Hz.

ii) Magnetic Applications:


Fast magnetic forming is becoming more and more important, especially for the
automotive industry. For fast magnetic forming applications, normally a capacitor is
charged to several kV, then the LTT is triggered by a laser pulse. The capacitor is
discharged into a special air coil. A crow -bar diode protects the capacitor against
negative charging. The object that is supposed to be deformed is placed in a special air
coil. In this way, for example, two pipes can be fixed together without using any kind of
rubber seal. LTTs are tested in this application with charging voltage of up to 5 kV, a load
dI/dt of 5 kA/s and a maximum load current of 35 kA.
iii) Laser Applications:
High-power lasers are used in lithography processes to produce processors and
TFT displays. First, a capacitor bank is charged to several kilovolts. Then, the LTTs are
triggered and the current flows through a coil to produce a well -defined current pulse.
This current pulse is compressed by two or more pulse-compression circuits. After this
compression, the current pulse triggers the laser. These laser applications normally work
at a frequency of several 100 H z. LTTs are tested in this application with a charging
voltage of 16 kV, a load dI/dt of 2 kA/s, a maximum load current of 2 kA, and a
frequency of 300 Hz.

REFERENCES:

M.S. Towers and P. Mawby, "Self protected light triggered thyristors", IEE Colloquium
Recent Advances in Power Devices, London, p. 8/1 -10, 1999.
http://www.slideshare.net/ideseditor/light-triggering-thyristor-for-hvdc-and-otherapplications
http://www.energy.siemens.com/co/en/powertransmission/hvdc/applicationsbenefits/hvdc-history.html
https://en.wikipedia.org/wiki/Thyristor
https://en.wikipedia.org/wiki/High-voltage_direct_current
https://en.wikipedia.org/wiki/Highvoltage_direct_current#Mercury_arc_valves

You might also like