Scribd
Upload
429 views

Lab 10 Diffraction and Interference

This document describes an experiment to investigate the optical phenomena of diffraction and interference using a He-Ne laser. The experiment involves using single and double slits to diffract the laser light and measure the diffraction patterns. From the patterns, the wavelength of the laser can be determined and compared to the manufacturer's specification. Students will design procedures to collect diffraction data from the single slit at varying widths and from the double slit at varying separations between the slits. Analysis of the diffraction patterns will allow calculation of the laser's wavelength.

Uploaded by

Meower
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
429 views

Lab 10 Diffraction and Interference

This document describes an experiment to investigate the optical phenomena of diffraction and interference using a He-Ne laser. The experiment involves using single and double slits to diffract the laser light and measure the diffraction patterns. From the patterns, the wavelength of the laser can be determined and compared to the manufacturer's specification. Students will design procedures to collect diffraction data from the single slit at varying widths and from the double slit at varying separations between the slits. Analysis of the diffraction patterns will allow calculation of the laser's wavelength.

Uploaded by

Meower
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

PHYS 25100 Heat, Electricity, and Optics Laboratory

Diffraction and Interference

Objectives
Investigate the optical phenomenon of diffraction and interference
Measure the wavelength of a Helium-Neon laser by diffraction techniques
and compare to the rated wavelength given by the manufacturer

Equipment

He-Ne Laser
Optical Bench
Diffraction Grates
Measuring Tape / Ruler

Introduction
Waves add up either when the original light wave is split up into two
constituent waves (double slit interference) or when the same portions of the
original light wave interfere with themselves (single slit or grating diffraction).
Fraunhofer diffraction deals with the limiting case where the light passing through
diffracting object is parallel and monochromatic, and where the image plane is at a
distance large compared to the size of the diffracting object.
Single Slit Diffraction
Under Fraunhofer conditions, a single slit will exhibit a light curve following
the single slit diffraction intensity expression. The narrower the slit, the broader
the peaks of light. The shape or "envelope" of this light curve will serve to set
limiting intensities for multiple slit arrangements, assuming that all the slits are
identical.

Last updated: Spring 2014

Rengstorf, Jackura


Figure 1. Single slit diffraction profile

The position of dark spots of the diffraction pattern from light shed on a single slit
can be written as

y=

mD
,
a

(1)

where the order m = {1,2,3,...} and y, , D, and a are described in Figure 2 below.


Figure 2. Diagram describing the single slit diffraction

Last updated: Spring 2014

Rengstorf, Jackura

Double Slit Diffraction and Interference


The pattern formed by the interference and diffraction of coherent light is
distinctly different for a single and double slit. As shown in Fig. 3, the single-slit
intensity envelope is shown by the dashed line and that of the double slit is seen
as a modulation inside the single-slit envelope. The photographs of the single and
double slit patterns produced by a helium-neon laser show the qualitative
differences between the patterns produced. The breaking up of the broad maxima
of the single slit pattern into more closely spaced maxima is evident. The number
of bright maxima within the central maximum of the single-slit pattern is
influenced by the width of the slit and the separation of the double slits.


Figure 3. Double slit diffraction profile

The position of bright spots of the diffraction pattern from light shed on a
double-slit can be written as

y=

mD
d

(2)

where the order m = {0,1,2,...} and y, , D, and d are described in Fig. 4 below.
(Note that the diagram shown below and as seen in lecture & textbooks is an
idealized double slit, which ignores the single-slit characteristics of each of the

Last updated: Spring 2014

Rengstorf, Jackura

two single slits. A real double slit exhibits closely spaced dark and light fringes,
superimposed over the single-slit pattern (as shown in Figs. 3 and 5). The single
slit profile is said to modulate the double slit pattern, as shown in Fig. 5.


Figure 4. Diagram describing the double slit diffraction

Procedure
PART A: SINGLE-SLIT DIFFRACTION
Design an experiment to measure the diffraction pattern of a laser of
unknown wavelength through a single slit. Determine the wavelength of the light.
If possible, take a picture of your diffraction pattern for your report. Repeat with
at least 2 more different slit widths. Average your results.
PART B: DOUBLE-SLIT INTERFERENCE & DIFFRACTION
Design an experiment to measure the diffraction pattern of the laser
through a double-slit. Take a snap shot of your diffraction pattern. Determine the
wavelength of the light. Repeat for at least 2 more different double-slit distances.
Average your results. Compare the results to Part A.

Last updated: Spring 2014

Rengstorf, Jackura


Figure 5. Image of diffraction experiment

Images taken from


http://hyperphysics.phy-astr.gsu.edu/hbase/hframe.html

Last updated: Spring 2014

Rengstorf, Jackura

You might also like