MES-2110 - Userguide
Uploaded by
Astefanesei AlexandruMES-2110 - Userguide
Uploaded by
Astefanesei AlexandruMES-2110
Intelligent Layer 2 Switch
Default Login Details
IP Address
http://192.168.1.1
User Name
admin
Password
1234
Firmware
Version 1.00
www.zyxel.com
Edition 4, 05/2010
www.zyxel.com
Copyright 2010
ZyXEL Communications Corporation
About This User's Guide
About This User's Guide
Intended Audience
This manual is intended for people who want to configure the MES-2110 using the
web configurator.
Related Documentation
Command Line Interface (CLI) Reference Guide
Line commands offer an alternative to the web configurator and in some cases
are necessary to configure advanced features.
Note: It is recommended you use the web configurator to configure the MES-2110.
Support Disc
Refer to the included CD for support documents.
ZyXEL Web Site
Please refer to www.zyxel.com for additional support documentation and
product certifications.
Documentation Feedback
Send your comments, questions or suggestions to: [email protected]
Thank you!
The Technical Writing Team, ZyXEL Communications Corp.,
6 Innovation Road II, Science-Based Industrial Park, Hsinchu, 30099, Taiwan.
Need More Help?
More help is available at www.zyxel.com.
MES-2110 Users Guide
About This User's Guide
Download Library
Search for the latest product updates and documentation from this link. Read
the Tech Doc Overview to find out how to efficiently use the User Guide, Quick
Start Guide and Command Line Interface Reference Guide in order to better
understand how to use your product.
Knowledge Base
If you have a specific question about your product, the answer may be here.
This is a collection of answers to previously asked questions about ZyXEL
products.
Forum
This contains discussions on ZyXEL products. Learn from others who use ZyXEL
products and share your experiences as well.
Customer Support
Should problems arise that cannot be solved by the methods listed above, you
should contact your vendor. If you cannot contact your vendor, then contact a
ZyXEL office for the region in which you bought the device.
See http://www.zyxel.com/web/contact_us.php for contact information. Please
have the following information ready when you contact an office.
Product model and serial number.
Warranty Information.
Date that you received your device.
Brief description of the problem and the steps you took to solve it.
MES-2110 Users Guide
Document Conventions
Document Conventions
Warnings and Notes
These are how warnings and notes are shown in this Users Guide.
Warnings tell you about things that could harm you or your device.
Note: Notes tell you other important information (for example, other things you may
need to configure or helpful tips) or recommendations.
Syntax Conventions
The MES-2110 may be referred to as the MES-2110, the device, the
system or the product in this Users Guide.
Product labels, screen names, field labels and field choices are all in bold font.
A key stroke is denoted by square brackets and uppercase text, for example,
[ENTER] means the enter or return key on your keyboard.
Enter means for you to type one or more characters and then press the
[ENTER] key. Select or choose means for you to use one of the predefined
choices.
A right angle bracket ( > ) within a screen name denotes a mouse click. For
example, Maintenance > Log > Log Setting means you first click
Maintenance in the navigation panel, then the Log sub menu and finally the
Log Setting tab to get to that screen.
Units of measurement may denote the metric value or the scientific value.
For example, k for kilo may denote 1000 or 1024, M for mega may
denote 1000000 or 1048576 and so on.
e.g., is a shorthand for for instance, and i.e., means that is or in other
words.
MES-2110 Users Guide
Document Conventions
Icons Used in Figures
Figures in this Users Guide may use the following generic icons. The MES-2110
icon is not an exact representation of your device.
The MES-2110
Computer
Notebook computer
Server
DSLAM
Firewall
Telephone
Router
MES-2110 Users Guide
Safety Warnings
Safety Warnings
Do NOT use this product near water, for example, in a wet basement or near a swimming
pool.
Do NOT expose your device to dampness, dust or corrosive liquids.
Do NOT store things on the device.
Do NOT install, use, or service this device during a thunderstorm. There is a remote risk
of electric shock from lightning.
Do not obstruct the device ventillation slots as insufficient airflow may harm your device.
Connect ONLY suitable accessories to the device.
Do NOT open the device or unit. Opening or removing covers can expose you to
dangerous high voltage points or other risks. ONLY qualified service personnel should
service or disassemble this device. Please contact your vendor for further information.
Make sure to connect the cables to the correct ports.
Place connecting cables carefully so that no one will step on them or stumble over them.
Always disconnect all cables from this device before servicing or disassembling.
Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right
supply voltage (for example, 110V AC in North America or 230V AC in Europe).
Use ONLY power wires of the appropriate wire gauge (see Chapter 25 on page 215 for
details) for your device. Connect it to a power supply of the correct voltage (see Chapter
25 on page 215 for details).
Do NOT allow anything to rest on the power adaptor or cord and do NOT place the
product where anyone can walk on the power adaptor or cord.
Do NOT use the device if the power adaptor or cord is damaged as it might cause
electrocution.
If the power adaptor or cord is damaged, remove it from the device and the power
source.
Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a
new one.
The length of exposed (bare) power wire should not exceed 7 mm.
Your product is marked with this symbol, which is known as the WEEE mark. WEEE
stands for Waste Electronics and Electrical Equipment. It means that used electrical
and electronic products should not be mixed with general waste. Used electrical and
electronic equipment should be treated separately.
MES-2110 Users Guide
Safety Warnings
MES-2110 Users Guide
Contents Overview
Contents Overview
Introduction ................................................................................................................................ 19
Hardware Installation and Connection ....................................................................................... 25
Hardware Overview ................................................................................................................... 29
Tutorials ..................................................................................................................................... 37
The Web Configurator ............................................................................................................... 51
System Details ........................................................................................................................... 61
Configuration ............................................................................................................................. 65
Loop Detection .......................................................................................................................... 71
Jumbo Frame ............................................................................................................................ 75
802.1x ........................................................................................................................................ 77
Bridge ........................................................................................................................................ 89
VLAN ......................................................................................................................................... 97
Bandwidth Control ....................................................................................................................111
Broadcast Storm Control ..........................................................................................................113
Port Mirroring ............................................................................................................................115
Link Aggregation .......................................................................................................................117
IGMP ....................................................................................................................................... 123
DHCP Relay Configuration ...................................................................................................... 137
IP Source Guard ...................................................................................................................... 141
MAC ......................................................................................................................................... 151
QoS ......................................................................................................................................... 157
Mgmt Config and System Restart Menu .................................................................................. 165
Command Line Interface ......................................................................................................... 179
Troubleshooting ....................................................................................................................... 207
Product Specifications ............................................................................................................. 215
MES-2110 Users Guide
Contents Overview
10
MES-2110 Users Guide
Table of Contents
Table of Contents
About This User's Guide .......................................................................................................... 3
Document Conventions............................................................................................................ 5
Safety Warnings........................................................................................................................ 7
Contents Overview ................................................................................................................... 9
Table of Contents.................................................................................................................... 11
Chapter 1
Introduction ............................................................................................................................. 19
1.1 Overview .............................................................................................................................. 19
1.1.1 Backbone Application ................................................................................................. 19
1.1.2 Bridging Example ....................................................................................................... 20
1.1.3 High Performance Switching Example ....................................................................... 21
1.1.4 IEEE 802.1Q VLAN Application Examples ................................................................ 21
1.1.5 Metro Ethernet ........................................................................................................... 22
1.2 Ways to Manage the MES-2110 .......................................................................................... 23
1.3 Good Habits for Managing the MES-2110 ........................................................................... 24
Chapter 2
Hardware Installation and Connection ................................................................................. 25
2.1 Installation Scenarios ......................................................................................................... 25
2.2 Desktop Installation Procedure ............................................................................................ 25
2.3 Mounting the MES-2110 on a Rack ..................................................................................... 26
2.3.1 Rack-mounted Installation Requirements .................................................................. 26
2.3.2 Attaching the Mounting Brackets to the MES-2110 .................................................... 27
2.3.3 Mounting the MES-2110 on a Rack ........................................................................... 28
Chapter 3
Hardware Overview................................................................................................................. 29
3.1 Front Panel .......................................................................................................................... 29
3.1.1 Console Port .............................................................................................................. 30
3.1.2 Gigabit Ethernet Ports ............................................................................................... 30
3.1.3 Mini-GBIC Slots .......................................................................................................... 31
3.2 AC Power Connection ......................................................................................................... 33
3.3 DC Power Connection ......................................................................................................... 34
3.4 LEDs ................................................................................................................................... 35
MES-2110 Users Guide
11
Table of Contents
Chapter 4
Tutorials ................................................................................................................................... 37
4.1 IGMP Snooping ................................................................................................................... 37
4.2 RADIUS Configuration ......................................................................................................... 38
4.3 MVR Configuration .............................................................................................................. 41
4.4 VLAN ID Priority .................................................................................................................. 44
4.5 Untrusted ARP Inspection ................................................................................................... 45
4.6 Outgoing Traffic Bandwidth ................................................................................................. 47
4.7 Frame Tagging ..................................................................................................................... 48
Chapter 5
The Web Configurator ............................................................................................................ 51
5.1 Introduction .......................................................................................................................... 51
5.2 System Login ....................................................................................................................... 51
5.3 The Main Screen ................................................................................................................. 53
5.3.1 Set Up the Administrative Password .......................................................................... 58
5.4 Saving Your Configuration ................................................................................................... 58
5.5 Switch Lockout .................................................................................................................... 59
5.6 Resetting the MES-2110 ...................................................................................................... 59
5.6.1 Reload the Configuration File ..................................................................................... 59
Chapter 6
System Details ........................................................................................................................ 61
6.1 Overview .............................................................................................................................. 61
6.2 The System Information Screen .......................................................................................... 61
6.3 The Board Information Screen ............................................................................................ 62
6.4 The DHCP Configuration Screen ........................................................................................ 63
Chapter 7
Configuration .......................................................................................................................... 65
7.1 Overview .............................................................................................................................. 65
7.2 The Port Configuration Screen ............................................................................................ 65
7.3 The Port Status Screen
................................................................................................... 67
7.4 The RMON Status Screen .................................................................................................. 68
Chapter 8
Loop Detection........................................................................................................................ 71
8.1 Overview .............................................................................................................................. 71
8.2 The Loop Detection Screen ................................................................................................. 72
Chapter 9
Jumbo Frame .......................................................................................................................... 75
9.1 Overview .............................................................................................................................. 75
12
MES-2110 Users Guide
Table of Contents
9.2 The Jumbo Frame Configuration Screen ............................................................................ 75
Chapter 10
802.1x ....................................................................................................................................... 77
10.1 Overview ........................................................................................................................... 77
10.1.1 IEEE 802.1x Authentication ..................................................................................... 77
10.1.2 Guest VLAN ............................................................................................................. 78
10.2 802.1x Global Configuration Screen .................................................................................. 79
10.3 802.1x Radius Server Configuration Screen ..................................................................... 80
10.4 802.1x Port Configuration Screen ..................................................................................... 81
10.5 802.1x Radius Server Configuration Screen ..................................................................... 83
10.6 Technical Reference .......................................................................................................... 84
10.6.1 RADIUS and TACACS+ .......................................................................................... 84
10.6.2 Supported RADIUS Attributes .................................................................................. 84
10.6.3 Attributes Used for Authentication ............................................................................ 85
10.6.4 Attributes Used for Accounting ................................................................................. 86
Chapter 11
Bridge....................................................................................................................................... 89
11.1 Overview ............................................................................................................................ 89
11.1.1 STP Terminology ...................................................................................................... 89
11.1.2 How STP Works ....................................................................................................... 90
11.1.3 STP Port States ........................................................................................................ 91
11.2 The Bridge Configuration Screen ....................................................................................... 91
11.3 The RSTP System Configuration Screen .......................................................................... 92
11.4 The Spanning Tree Port Configuration .............................................................................. 95
Chapter 12
VLAN ........................................................................................................................................ 97
12.1 Overview ............................................................................................................................ 97
12.2 Introduction to IEEE 802.1Q Tagged VLANs
................................................................ 97
12.2.1 Forwarding Tagged and Untagged Frames .............................................................. 98
12.3 The VLAN Type Screen ..................................................................................................... 99
12.4 The Port-Based VLAN Screen ........................................................................................... 99
12.5 The Tag-Based VLAN Screens ........................................................................................ 101
12.5.1 VLAN Stacking ....................................................................................................... 101
12.5.2 VLAN Stacking Example ........................................................................................ 101
12.5.3 VLAN Stacking Port Roles ..................................................................................... 102
12.5.4 VLAN Tag Format ................................................................................................... 103
12.5.5 Frame Format ........................................................................................................ 104
12.5.6 The VLAN Stacking Configuration Screen ............................................................. 105
12.5.7 The Tag-Based Port Information Screen ................................................................ 107
12.5.8 The Tag-Based Port Configuration Screen ............................................................ 108
MES-2110 Users Guide
13
Table of Contents
12.5.9 The Management VLAN Screen ............................................................................ 109
Chapter 13
Bandwidth Control................................................................................................................ 111
13.1 Overview ..........................................................................................................................111
13.2 Bandwidth Control Setup ..................................................................................................111
Chapter 14
Broadcast Storm Control ..................................................................................................... 113
14.1 Overview ...........................................................................................................................113
14.2 Broadcast Storm Control Setup .......................................................................................113
Chapter 15
Port Mirroring ........................................................................................................................ 115
15.1 Overview ...........................................................................................................................115
15.2 Port Mirroring Setup ........................................................................................................115
Chapter 16
Link Aggregation .................................................................................................................. 117
16.1 Overview ..........................................................................................................................117
16.2 Dynamic Link Aggregation ................................................................................................117
16.2.1 Link Aggregation ID .................................................................................................118
16.3 Static Trunking Example ...................................................................................................118
16.4 Link Aggregation Setting .................................................................................................119
16.5 Link Aggregation Control Protocol
................................................................................ 120
16.6 LACP Link Status ............................................................................................................ 121
Chapter 17
IGMP....................................................................................................................................... 123
17.1 Overview ......................................................................................................................... 123
17.1.1 IP Multicast Addresses ........................................................................................... 123
17.1.2 IGMP Snooping ...................................................................................................... 123
17.1.3 IGMP Snooping and VLANs ................................................................................... 124
17.2 IGMP Configuration ......................................................................................................... 124
17.2.1 IGMP VLAN Query Mode ....................................................................................... 126
17.3 IGMP Status ................................................................................................................... 127
17.4 MVR Overview ................................................................................................................ 127
17.4.1 Types of MVR Ports ............................................................................................... 128
17.4.2 MVR Modes ........................................................................................................... 128
17.4.3 How MVR Works .................................................................................................... 128
17.5 General MVR Configuration ............................................................................................ 129
17.6 MVR Group Configuration .............................................................................................. 131
17.6.1 MVR Configuration Example .................................................................................. 133
14
MES-2110 Users Guide
Table of Contents
Chapter 18
DHCP Relay Configuration................................................................................................... 137
18.1 Overview .......................................................................................................................... 137
18.1.1 DHCP Relay Agent Information ............................................................................. 137
18.2 DHCP Relay Configuration .............................................................................................. 138
Chapter 19
IP Source Guard.................................................................................................................... 141
19.1 Overview .......................................................................................................................... 141
19.1.1 DHCP Snooping Overview ..................................................................................... 142
19.2 DHCP Snooping Configuration ........................................................................................ 143
19.3 DHCP Binding Table ........................................................................................................ 145
19.4 The ARP Inspection Screen ............................................................................................ 147
19.4.1 Configuring ARP Inspection ................................................................................... 147
Chapter 20
MAC........................................................................................................................................ 151
20.1 Overview .......................................................................................................................... 151
20.2 The MAC Table Status Screen ........................................................................................ 152
20.3 The Lock MAC Address Learning Screen ....................................................................... 153
20.4 The MAC Filter Configuration Screen .............................................................................. 154
20.5 The MAC Limit Configuration Screen .............................................................................. 156
Chapter 21
QoS......................................................................................................................................... 157
21.1 Overview .......................................................................................................................... 157
21.2 The QoS Base Configuration Screen .............................................................................. 157
21.2.1 Configuring the Base Configuration Screen ........................................................... 158
21.3 The 802.1p Priority Table ................................................................................................. 160
21.4 The Tag Priority Table ...................................................................................................... 161
21.5 The IP DSCP Priority Table ............................................................................................. 161
21.6 The Priority Override Configuration Screen ..................................................................... 163
Chapter 22
Mgmt Config and System Restart Menu ............................................................................. 165
22.1 Overview .......................................................................................................................... 165
22.2 The Serial Port Configuration Screen .............................................................................. 165
22.3 The SNMP Configuration Screens .................................................................................. 166
22.3.1 The SNMP Communities Screen ........................................................................... 167
22.3.2 The IP Trap Manager Screen ................................................................................. 167
22.4 The SNTP Screen ........................................................................................................... 168
22.5 Alarms and Logs .............................................................................................................. 170
22.6 The User Configuration Screen ....................................................................................... 172
MES-2110 Users Guide
15
Table of Contents
22.7 The Cable Test Screen .................................................................................................... 173
22.8 The Host DoS Protection ................................................................................................. 174
22.9 The Port Abnormal Traffic Detection Screen ................................................................... 175
22.10 Upgrading the Firmware ................................................................................................ 176
22.11 Managing the Configuration File .................................................................................... 177
22.12 Restarting the System ................................................................................................... 178
Chapter 23
Command Line Interface ...................................................................................................... 179
23.1 Overview .......................................................................................................................... 179
23.1.1 Console Port Management .................................................................................... 179
23.1.2 Logging in ............................................................................................................... 179
23.1.3 Using Shortcuts and Getting Help .......................................................................... 180
23.2 Saving Changes .............................................................................................................. 180
23.3 Logging Out ..................................................................................................................... 181
23.4 Command Modes ............................................................................................................ 181
23.5 Basic Commands ............................................................................................................ 182
23.6 Privileged Command Mode ............................................................................................. 183
23.7 Configuration Mode ......................................................................................................... 186
23.7.1 IGMP Snooping Example ....................................................................................... 193
23.7.2 RADIUS Configuration Example ............................................................................ 194
23.8 MVR Mode ....................................................................................................................... 195
23.8.1 MVR Command Example ....................................................................................... 196
23.9 VLAN Mode ..................................................................................................................... 197
23.9.1 VLAN ID Priority Example ...................................................................................... 198
23.10 Interface Mode ............................................................................................................... 198
23.10.1 Untrusted ARP Inspection Example ..................................................................... 203
23.10.2 Outgoing Traffic Bandwidth Limit Example .......................................................... 203
23.10.3 Frame Tagging Examples .................................................................................... 204
Chapter 24
Troubleshooting.................................................................................................................... 207
24.1 Power, Hardware Connections, and LEDs ...................................................................... 207
24.2 MES-2110 Access and Login ........................................................................................... 208
24.3 MES-2110 Configuration and Console .............................................................................211
Chapter 25
Product Specifications ......................................................................................................... 215
Appendix A Changing a Fuse............................................................................................... 219
Appendix B Common Services............................................................................................. 221
Appendix C Legal Information .............................................................................................. 225
16
MES-2110 Users Guide
Table of Contents
Index....................................................................................................................................... 229
MES-2110 Users Guide
17
Table of Contents
18
MES-2110 Users Guide
CHAPTER
1
Introduction
1.1 Overview
This chapter introduces the main features and applications of the MES-2110.
The MES-2110 is a layer-2 standalone Ethernet switch with additional layer-2,
layer-3, and layer-4 features suitable for metro ethernets. The MES-2110 has
eight 10/100 Mbps Ethernet ports and two mini-GBIC slots. It also has two GbE
dual personality interfaces with each interface comprising one mini-GBIC slot and
one 10/100/1000 Mbps RJ-45 port, with either port or slot active at a time.
With its built-in Web Configurator, managing and configuring the MES-2110 is
easy. In addition, the MES-2110 can also be managed via Telnet, any terminal
emulator program on the console port, or third-party SNMP management.
See Chapter 25 on page 215 for a full list of software features available on the
MES-2110.
This section shows a few examples of using the MES-2110 in various network
environments.
1.1.1 Backbone Application
The MES-2110 is an ideal solution for small networks where rapid growth can be
expected in the near future. The MES-2110 can be used standalone for a group of
heavy traffic users. You can connect computers and servers directly to the MES2110s port or connect other switches to the MES-2110.
MES-2110 Users Guide
19
Chapter 1 Introduction
In this example, all computers can share high-speed applications on the server. To
expand the network, simply add more networking devices such as switches,
routers, computers, print servers etc.
Figure 1 Backbone Application
1.1.2 Bridging Example
In this example, the MES-2110 connects different company departments (RD and
Sales) to the corporate backbone. It can alleviate bandwidth contention and
eliminate server and network bottlenecks. All users that need high bandwidth can
connect to high-speed department servers via the MES-2110. You can provide a
super-fast uplink connection by using a Gigabit Ethernet/mini-GBIC port on the
MES-2110.
Moreover, the MES-2110 eases supervision and maintenance by allowing network
managers to centralize multiple servers at a single location.
Figure 2 Bridging Application
20
MES-2110 Users Guide
Chapter 1 Introduction
1.1.3 High Performance Switching Example
The MES-2110 is ideal for connecting two networks that need high bandwidth. In
the following example, use trunking to connect these two networks.
Switching to higher-speed LANs such as ATM (Asynchronous Transmission Mode)
is not feasible for most people due to the expense of replacing all existing
Ethernet cables and adapter cards, restructuring your network and complex
maintenance. The MES-2110 can provide the same bandwidth as ATM at much
lower cost while still being able to use existing adapters and switches. Moreover,
the current LAN structure can be retained as all ports can freely communicate with
each other.
Figure 3 High Performance Switched Workgroup Application
1.1.4 IEEE 802.1Q VLAN Application Examples
A VLAN (Virtual Local Area Network) allows a physical network to be partitioned
into multiple logical networks. Stations on a logical network belong to one group.
A station can belong to more than one group. With VLAN, a station cannot directly
talk to or hear from stations that are not in the same group(s) unless such traffic
first goes through a router.
For more information on VLANs, refer to Chapter 12 on page 97.
1.1.4.1 Tag-based VLAN Example
Ports in the same VLAN group share the same frame broadcast domain thus
increase network performance through reduced broadcast traffic. VLAN groups
can be modified at any time by adding, moving or changing ports without any recabling.
MES-2110 Users Guide
21
Chapter 1 Introduction
Shared resources such as a server can be used by all ports in the same VLAN as
the server. In the following figure only ports that need access to the server need
to be part of VLAN 1. Ports can belong to other VLAN groups too.
Figure 4 Shared Server Using VLAN Example
1.1.5 Metro Ethernet
The MES-2110 is ideal for connecting users to an Ethernet network that spans a
metropolitan area.
In the following example, the MES-2110 is one of many switches that connect
users in the metropolitan area to the Internet. The metro ethernet is based on a
star (or hub-and-spoke) topology, though other topologies, such as ring or mesh,
are also possible. The MES-2110 is connected to the backbone and the
22
MES-2110 Users Guide
Chapter 1 Introduction
metropolitan servers over an optical network that provides higher bandwidth than
copper.
Figure 5 Metro Ethernet
1.2 Ways to Manage the MES-2110
Use any of the following methods to manage the MES-2110.
Web Configurator. This is recommended for everyday management of the MES2110 using a (supported) web browser. See Chapter 5 on page 51.
Command Line Interface. Line commands offer an alternative to the web
configurator and in some cases are necessary to configure advanced features.
See the CLI Reference Guide.
SNMP. The MES-2110 can be monitored by an SNMP manager. See Section 22.3
on page 166.
MES-2110 Users Guide
23
Chapter 1 Introduction
1.3 Good Habits for Managing the MES-2110
Do the following things regularly to make the MES-2110 more secure and to
manage the MES-2110 more effectively.
Change the password. Use a password thats not easy to guess and that consists
of different types of characters, such as numbers and letters.
Write down the password and put it in a safe place.
Back up the configuration (and make sure you know how to restore it).
Restoring an earlier working configuration may be useful if the device becomes
unstable or even crashes. If you forget your password, you will have to reset the
MES-2110 to its factory default settings. If you backed up an earlier
configuration file, you would not have to totally re-configure the MES-2110. You
could simply restore your last configuration.
24
MES-2110 Users Guide
CHAPTER
Hardware Installation and
Connection
2.1 Installation Scenarios
This chapter shows you how to install and connect the MES-2110.
The MES-2110 can be placed on a desktop or rack-mounted on a standard EIA
rack. Use the rubber feet in a desktop installation and the brackets in a rackmounted installation.
Note: For proper ventilation, allow at least 4 inches (10 cm) of clearance at the front
and 3.4 inches (8 cm) at the back of the MES-2110. This is especially important
for enclosed rack installations.
2.2 Desktop Installation Procedure
1
Make sure the MES-2110 is clean and dry.
Set the MES-2110 on a smooth, level surface strong enough to support the weight
of the MES-2110 and the connected cables. Make sure there is a power outlet
nearby.
Make sure there is enough clearance around the MES-2110 to allow air circulation
and the attachment of cables and the power cord.
Remove the adhesive backing from the rubber feet.
MES-2110 Users Guide
25
Chapter 2 Hardware Installation and Connection
Attach the rubber feet to each corner on the bottom of the MES-2110. These
rubber feet help protect the MES-2110 from shock or vibration and ensure space
between devices when stacking.
Figure 6 Attaching Rubber Feet
Note: Do NOT block the ventilation holes. Leave space between devices when
stacking.
2.3 Mounting the MES-2110 on a Rack
The MES-2110 can be mounted on an EIA standard size, 19-inch rack or in a
wiring closet with other equipment. Follow the steps below to mount your MES2110 on a standard EIA rack using a rack-mounting kit.
Note: The following sections feature the AC model of the MES-2110 but are equally
applicable to the DC model.
2.3.1 Rack-mounted Installation Requirements
Two mounting brackets.
Eight M3 flat head screws and a #2 Philips screwdriver.
Four M5 flat head screws and a #2 Philips screwdriver.
Failure to use the proper screws may damage the unit.
26
MES-2110 Users Guide
Chapter 2 Hardware Installation and Connection
2.3.1.1 Precautions
Make sure the rack will safely support the combined weight of all the equipment
it contains.
Make sure the position of the MES-2110 does not make the rack unstable or
top-heavy. Take all necessary precautions to anchor the rack securely before
installing the unit.
2.3.2 Attaching the Mounting Brackets to the MES-2110
1
Position a mounting bracket on one side of the MES-2110, lining up the four screw
holes on the bracket with the screw holes on the side of the MES-2110.
Figure 7 Attaching the Mounting Brackets
Using a #2 Philips screwdriver, install the M3 flat head screws through the
mounting bracket holes into the MES-2110.
Repeat steps 1 and 2 to install the second mounting bracket on the other side of
the MES-2110.
You may now mount the MES-2110 on a rack. Proceed to the next section.
MES-2110 Users Guide
27
Chapter 2 Hardware Installation and Connection
2.3.3 Mounting the MES-2110 on a Rack
1
Position a mounting bracket (that is already attached to the MES-2110) on one
side of the rack, lining up the two screw holes on the bracket with the screw holes
on the side of the rack.
Figure 8 Mounting the MES-2110 on a Rack
28
Using a #2 Philips screwdriver, install the M5 flat head screws through the
mounting bracket holes into the rack.
Repeat steps 1 and 2 to attach the second mounting bracket on the other side of
the rack.
MES-2110 Users Guide
CHAPTER
Hardware Overview
This chapter describes the front panel and rear panel of the MES-2110 and shows
you how to make the hardware connections.
3.1 Front Panel
The following figure shows the front panel of the MES-2110.
Figure 9 Front Panel
LEDs
DC Terminal
Block Header
Console Port
Mini-GBIC slots
Dual Personality
Interfaces
Ethernet
Ports
AC Power Connection
MES-2110 Users Guide
29
Chapter 3 Hardware Overview
The following table describes the port labels on the front panel.
Table 1 Front Panel Connections
LABEL
DESCRIPTION
Power
Connection
Connect an appropriate power supply to this port.
8 10/100
Mbps RJ-45
Ethernet
Ports
Connect these ports to a computer, a hub, an Ethernet switch or router.
Two MiniGBIC Slots
Use mini-GBIC transceivers in these slots for fiber-optic or copper
connections to backbone Ethernet switches.
Two Dual
Personality
Interfaces
Each interface has one 1000 Base-T copper RJ-45 port and one mini-GBIC
slot, with one port active at a time.
Console Port
10/100/1000 Mbps RJ-45 GbE Ports:
Connect these Gigabit Ethernet ports to high-bandwidth backbone
network Ethernet switches.
Mini-GBIC Slots:
Use mini-GBIC transceivers in these slots for fiber-optic or copper
connections to backbone Ethernet switches.
The console port is for local configuration of the MES-2110.
3.1.1 Console Port
For local management, you can use a computer with terminal emulation software
configured to the following parameters:
VT100
Terminal emulation
9600 bps
No parity, 8 data bits, 1 stop bit
No flow control
Connect the male 9-pin end of the console cable to the console port of the MES2110. Connect the female end to a serial port (COM1, COM2 or other COM port) of
your computer.
3.1.2 Gigabit Ethernet Ports
The MES-2110 has 1000Base-T auto-negotiating, auto-crossover Ethernet ports.
In 10/100/1000 Mbps Fast Ethernet, the speed can be 10 Mbps, 100 Mbps or 1000
Mbps and the duplex mode can be half duplex or full duplex.
An auto-negotiating port can detect and adjust to the optimum Ethernet speed
(10/100/1000 Mbps) and duplex mode (full duplex or half duplex) of the
connected device.
30
MES-2110 Users Guide
Chapter 3 Hardware Overview
An auto-crossover (auto-MDI/MDI-X) port automatically works with a straightthrough or crossover Ethernet cable.
Two of the 1000Base-T Ethernet ports are paired with a mini-GBIC slot to create a
dual personality interface. The MES-2110 uses up to one connection for each miniGBIC and 1000Base-T Ethernet pair. The mini-GBIC slots have priority over the
Gigabit ports. This means that if a mini-GBIC slot and the corresponding GbE port
are connected at the same time, the GbE port will be disabled.
When auto-negotiation is turned on, a Ethernet port negotiates with the peer
automatically to determine the connection speed and duplex mode. If the peer
Ethernet port does not support auto-negotiation or turns off this feature, the MES2110 determines the connection speed by detecting the signal on the cable and
using half duplex mode. When the MES-2110s auto-negotiation is turned off, an
Ethernet port uses the pre-configured speed and duplex mode when making a
connection, thus requiring you to make sure that the settings of the peer Ethernet
port are the same in order to connect.
3.1.2.1 Default Ethernet Negotiation Settings
The factory default negotiation settings for the Gigabit ports on the MES-2110
are:
Speed: Auto
Duplex: Auto
Flow control: Off
Link Aggregation: Disabled
3.1.2.2 Auto-crossover
All ports are auto-crossover, that is auto-MDIX ports (Media Dependent Interface
Crossover), so you may use either a straight-through Ethernet cable or crossover
Ethernet cable for all Gigabit port connections. Auto-crossover ports automatically
sense whether they need to function as crossover or straight ports, so crossover
cables can connect both computers and switches/hubs.
3.1.3 Mini-GBIC Slots
These are slots for mini-GBIC (Gigabit Interface Converter) transceivers. A
transceiver is a single unit that houses a transmitter and a receiver. The MES-2110
does not come with transceivers. You must use transceivers that comply with the
Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA). See
the SFF committees INF-8074i specification Rev 1.0 for details.
MES-2110 Users Guide
31
Chapter 3 Hardware Overview
You can change transceivers while the MES-2110 is operating. You can use
different transceivers to connect to Ethernet switches with different types of fiberoptic or even copper cable connectors.
To avoid possible eye injury, do not look into an operating fiberoptic modules connectors.
Type: SFP connection interface
Connection speed: 1 Gigabit per second (Gbps)
3.1.3.1 Transceiver Installation
Use the following steps to install a mini-GBIC transceiver (SFP module).
1
Insert the transceiver into the slot with the exposed section of PCB board facing
down.
Press the transceiver firmly until it clicks into place.
The MES-2110 automatically detects the installed transceiver. Check the LEDs to
verify that it is functioning properly.
Close the transceivers latch (latch styles vary).
Connect the fiber optic cables to the transceiver.
Figure 10 Transceiver Installation Example
Figure 11 Connecting the Fiber Optic Cables
3.1.3.2 Transceiver Removal
Use the following steps to remove a mini-GBIC transceiver (SFP module).
32
Remove the fiber optic cables from the transceiver.
Open the transceivers latch (latch styles vary).
MES-2110 Users Guide
Chapter 3 Hardware Overview
Pull the transceiver out of the slot.
Figure 12 Removing the Fiber Optic Cables
Figure 13 Opening the Transceivers Latch Example
Figure 14 Transceiver Removal Example
3.2 Power Connections Overview
Use the following procedures to connect the MES-2110 to a power source after
you have installed it.
Note: Check the power supply requirements in Chapter 25 on page 215, and make
sure you are using an appropriate power source.
Keep the power supply switch and the MES-2110s power switch in
the OFF position until you come to the procedure for turning on
the power.
Use only power wires of the required diameter for connecting the MES2110 to a power supply.
MES-2110 Users Guide
33
Chapter 3 Hardware Overview
3.2.1 AC Power Connection
Note: This is only for the AC model of the MES-2110.
Connect the female end of the power cord to the power socket of your MES-2110.
Connect the other end of the cord to a power outlet. Make sure that no objects
obstruct the airflow of the fans.
3.2.2 DC Power Connection
Note: This is only for the DC model of the MES-2110.
The MES-2110 uses a single ETB series terminal block plug with four pins which
allows you to connect up to two separate power supplies. If one power supply fails
the system can operate on the remaining power supply. Use two wires to connect
to a single terminal pair, one wire for the positive terminal and one wire for the
negative terminal.
Note: The current rating of the power wires must be greater than 20 Amps. The power
supply to which the MES-2110 connects must have a built-in circuit breaker or
switch to toggle the power.
Note: When installing the power wire, push it wire firmly into the terminal as deep as
possible and make sure that no exposed (bare) wire can be seen or touched.
An exposed wire from a DC power source can be dangerous. Use
extreme care when connecting a DC power source to the device.
To connect a power supply:
34
Use a screwdriver to loosen the terminal block captive screws.
Connect one end of a power wire to the MES-2110s RTN (return) pin and tighten
the captive screw.
Connect the other end of the power wire to the positive terminal on the power
supply.
Connect one end of a power wire to the MES-2110s -48V (input) pin and tighten
the captive screw.
Connect the other end of the power wire to the negative terminal on the power
supply.
Insert the terminal block plug in the MES-2110s terminal block header.
MES-2110 Users Guide
Chapter 3 Hardware Overview
3.2.3 Powering on the MES-2110
1
Turn on the power supply first.
Turn on the MES-2110s power second.
3.3 LEDs
After you connect the power to the MES-2110, view the LEDs to ensure proper
functioning of the MES-2110 and as an aid in troubleshooting.
Table 2 LED Descriptions
LED
COLOR STATU
S
DESCRIPTION
PWR
Green
On
The system is turned on.
Off
The system is off.
On
The system is on and functioning properly.
Blinking
The system is rebooting and performing self-diagnostic
tests.
Off
The power is off or the system is not ready/malfunctioning.
Blinking
The system is transmitting/receiving to/from a 10 Mbps
Ethernet network.
On
The link to a 10 Mbps Ethernet network is up.
Blinking
The system is transmitting/receiving to/from a 100 Mbps
Ethernet network.
On
The link to a 100 Mbps Ethernet network is up.
Off
The link to an Ethernet network is down.
On
The link to this port is up.
Off
The link to this port is not connected.
On
The link to an Ethernet network is on.
Blinking
This port is receiving or transmitting data.
Off
The port is not receiving or transmitting data.
SYS
Green
Ethernet Ports
LINK/
ACT
Green
Amber
Mini-GBIC Slots
LNK
ACT
Green
Green
1000Base-T Ethernet Ports (in Dual Personality Interface)
MES-2110 Users Guide
35
Chapter 3 Hardware Overview
Table 2 LED Descriptions (continued)
LED
STATU
COLOR S
ACT
Green
Amber
36
DESCRIPTION
Blinking
The system is transmitting/receiving to/from a 10 Mbps or
a 1000 Mbps Ethernet network.
On
The link to a 10 Mbps or a 1000 Mbps Ethernet network is
up.
Blinking
The system is transmitting/receiving to/from a 100 Mbps
Ethernet network.
On
The link to a 100 Mbps Ethernet network is up.
Off
The link to an Ethernet network is down.
MES-2110 Users Guide
CHAPTER
4
Tutorials
4.1 IGMP Snooping
IGMP snooping allows a layer-2 device such as the MES-2110 to eavesdrop on
IGMP-based data packets traversing the communications channel on layer-3. This
allows it to determine which ports should specifically receive multicast traffic in
order to prevent multicasting flooding across all of its ports.
This tutorial shows you how to enable IGMP snooping, set IGMP to automatic
query mode, and then set port 10 to static.
To configure IGMP snooping:
In the Web Configurator, open the Configuration > IGMP Menu > IGMP
Configuration screen.
Set IGMP Snooping to Enable.
MES-2110 Users Guide
37
Chapter 4 Tutorials
Set IGMP Query Mode to Auto.
Set the Static Query field for port 10 to Enable.
Click Apply. The new settings appear in the IGMP Status table.
Click Save Settings in the navigation panel to store the changes permanently.
4.2 RADIUS Configuration
RADIUS is a protocol explicitly designed to manage single location authentication
and authorization for an entire network. It also provides accounting services for
client usage of network resources.
This tutorial shows you how to set up one RADIUS server (172.16.10.10) and a
shared secret key (hello) for authentication.
To assign a RADIUS server to the MES-2110:
1
38
Open the Configuration > VLAN Menu > VLAN Type menu, set VLAN Type to
Tag-Based(802.1q), then click Apply.
MES-2110 Users Guide
Chapter 4 Tutorials
On the Configuration > VLAN Menu > Tag-Based(802.1q) > Tag-Based
info. screen, add VLAN ID 99 and click Apply. The new VLAN ID appears in the
Tag VLAN Status table.
Open the Configuration > 802.1x > Global Configuration screen. For the
802.1x option, select Enable. For the Guest VLAN option, select Enable and
enter 99 in the associated field. Click Apply to save these changes.
MES-2110 Users Guide
39
Chapter 4 Tutorials
40
Next go to the Configuration > 802.1x > RADIUS Server Configuration
screen. For Server IP Address, enter 172.16.10.10 and for Shared Server Key
enter hello, then click Apply.
Finally, open the Configuration > 802.1x > Port Configuration screen. From
the Port Number menu select Port 1 if not already selected, set the Guest
VLAN option to Enable, and click Apply.
MES-2110 Users Guide
Chapter 4 Tutorials
Click Save Settings in the navigation panel to store the changes permanently.
4.3 MVR Configuration
MVR manages multicast traffic from an upstream VLAN on a multicast server to
downstream subscribers in the same VLAN group. This allows you to regulate
bandwidth by not streaming multicast traffic to every device on your network but
rather just to the intended computers.
This tutorial shows you set up a Multicast VLAN Registration (MVR) group and then
direct all multicast traffic with matching VLAN IDs to it.
For the purposes of this tutorial, use the following settings:
Table 3 MVR Tutorial Values
SETTING
VALUE
VLAN Name
StreamVlan
VLAN ID
100
Source Port
Receiver Ports
1-4, 10
Multicast Group Mode
Dynamic
Tagging Ports
9, 10
Multicast Group IP Addresses
223.3.3.1 ~ 223.3.3.10
Multicast Group ID
Note: Make sure your Configuration > VLAN Menu > VLAN Type is set to TagBased(802.1q) before proceeding.
MES-2110 Users Guide
41
Chapter 4 Tutorials
To configure MVR:
10
4
5
7
6
8
9
Open the Configuration > IGMP Menu > MVR screen.
Select Active to enable the MVR feature.
Enter StreamVlan as the MVR Name.
Enter 100 as the Multicast VLAN ID.
Set the MVR Mode to Dynamic.
In the Source Port column, deselect all ports except Port 9. This will be the
source port which receives all incoming multicasts from upstream.
In the Receiver Port column, select Ports 1-4 and Port 10. These ports are now
the designated downstream recipients for all incoming multicasts.
In the Tagging column, enable tagging for Port 9 and 10.
Click Apply to store these changes.
10 Click the Group Configuration link.
42
MES-2110 Users Guide
Chapter 4 Tutorials
11 In the Group Configuration screen, select the Multicast VLAN ID you created
in step 4 from the list. In this example, it is VLAN ID 100.
11
12
12 Enter a Group ID of 1, a Start Address of 227.3.3.1, and a Quantity of 10.
13 Click Add, then click Save Settings in the navigation panel to store the changes
permanently.
MES-2110 Users Guide
43
Chapter 4 Tutorials
4.4 VLAN ID Priority
This tutorial assigns port 1 as a tagged port for VLAN 1 and sets the priority of all
incoming packets from VLAN 1 to priority 3.
Note: Make sure your Configuration > VLAN Menu > VLAN Type is set to TagBased(802.1q) before proceeding.
To configure VLAN ID priority:
2
4
5
44
Open the Configuration > VLAN Menu > Tag-Based(802.1q) > Tag-Based
info. screen.
For VLAN ID, select Add from the menu and enter 2 in the associated field.
Set the Priority to 1.
For Pri-Overide, select Enable.
In the Member column for Port 1, select Tagging.
Click Apply.
MES-2110 Users Guide
Chapter 4 Tutorials
Click Save Settings in the navigation panel to store the changes permanently.
4.5 Untrusted ARP Inspection
This tutorial shows you how to assign port 1 to 8 as untrusted for ARP inspection.
Generally if you want to enable ARP inspection on the device you also have to
enable DHCP snooping first to build a binding table.
To set up ARP inspection:
1
Open the Configuration > IP Source Guard > DHCP > DHCP Snooping
Configuration screen.
1
2
MES-2110 Users Guide
45
Chapter 4 Tutorials
Set Action to Enable and DHCP Snooping VLAN Mode to All-VLAN.
Click Apply.
Open the Configuration > IP Source Guard > ARP Inspection > ARP
Inspection Configuration screen.
4
5
6
8
46
Set Action to Enable and ARP Inspection VLAN Mode to All-VLAN.
In the Trust column, select Port 9 and Port 10.
In the Untrust column, select Ports 1-8.
Click Apply.
Click Save Settings in the navigation panel to store the changes permanently.
MES-2110 Users Guide
Chapter 4 Tutorials
4.6 Outgoing Traffic Bandwidth
This tutorial shows you how to set the outgoing traffic bandwidth limit to 1 Mbps
for Port 2.
To configure outgoing traffic bandwidth:
3
4
1
Open the Configuration > Bandwidth Control screen.
Set the Port Number to Port 2.
In the Egress row, set the Rate Level to 1M~100M (1M+), the Rate Limit to
1000 k, and the Active option to Enable.
Click Apply.
Click Save Settings in the navigation panel to store the changes permanently.
MES-2110 Users Guide
47
Chapter 4 Tutorials
4.7 Frame Tagging
In this tutorial, shows you how to configure ports 1 and 2 on the switch to tag
incoming frames with the service providers VID of 37 (ports are connected to
customer A network) and how to set the priority for ports 1 and 2 to 3.
The scenario is that both A and B are Service Providers Network (SPN) customers
with VPN tunnels between their head offices and branch offices respectively. Both
have an identical VLAN tag for their VLAN group. The service provider can
separate these two VLANs within its network by adding tag 37 to distinguish
customer A and tag 48 to distinguish customer B at edge device x and then
stripping those tags at edge device y as the data frames leave the network.
Figure 15 Frame Tagging Example
48
MES-2110 Users Guide
Chapter 4 Tutorials
To configure frame tagging:
4
1
Open the Configuration > VLAN Menu > Tag-Based(802.1q) > VLAN
Stacking screen.
Select Active and click Apply.
For Port 1 and Port 2, use the following settings: for Role select Access, for
PVID use 37 and for Priority choose 1.
Note: If the port for which you are configuring frame tagging is the same port by which
you connect to the MES-2110 then your computer should use the same PVID or
you should switch a non-tagged port.
4
Click Apply.
Click Save Settings in the navigation panel to store the changes permanently.
MES-2110 Users Guide
49
Chapter 4 Tutorials
50
MES-2110 Users Guide
CHAPTER
The Web Configurator
5.1 Introduction
This section introduces the configuration and functions of the web configurator.
The web configurator is an HTML-based management interface that allows easy
MES-2110 setup and management via Internet browser. Use Internet Explorer 6.0
and later or Firefox 1.5 and later versions. The recommended screen resolution is
1024 by 768 pixels.
In order to use the web configurator you need to allow:
Web browser pop-up windows from your device. Web pop-up blocking is enabled
by default in Windows XP SP (Service Pack) 2.
JavaScript (enabled by default).
Java permissions (enabled by default).
5.2 System Login
1
Start your web browser.
Type http:// and the IP address of the MES-2110 (for example, the default is
192.168.1.1) in the Location or Address field. Press [ENTER].
MES-2110 Users Guide
51
Chapter 5 The Web Configurator
The login screen appears. Enter the user name (admin by default) and password
(1234 by default).
Figure 16 Web Configurator: Login
52
Click OK to view the first web configurator screen.
MES-2110 Users Guide
Chapter 5 The Web Configurator
5.3 The Main Screen
The Main screen is the first screen that displays when you access the web
configurator.
The following figure shows the navigating components of a web configurator
screen.
Figure 17 Web Configurator Main Screen
A - Click the menu items to open submenu links, and then click on a submenu link
to open the screen in the main window.
MES-2110 Users Guide
53
Chapter 5 The Web Configurator
In the navigation panel, click a main link to reveal a list of submenu links.
Table 4 Navigation Panel Sub-links Overview
SYSTEM DETAILS
54
CONFIGURATION
MGMT CONFIG
SYSTEM RESTART
MENU
MES-2110 Users Guide
Chapter 5 The Web Configurator
The following table lists the various web configurator screens within the sub-links.
Table 5 Web Configurator Screen Sub-links Details
SYSTEM DETAILS
CONFIGURATION
MGMT CONFIG
SYSTEM
RESTART
MENU
System Info.
Port Configuration
Serial Port Config
Restart Option
Board Info.
Port Status
SNMP Config
DHCP Config
Rmon Status
Loop Detection
SNMP
Communities
IP Trap Manager
Jumbo Frame
SNTP
802.1
Email Alarm & SYSLog
Global Configuration
RADIUS Server Configuration
Port Configuration
802.1x Status
Bridge Menu
Bridge Config
RSTP System Config
RSTP Per Port Config
VLAN Menu
VLAN Type
Port-Based
Tag-Based (802.1q)
VLAN Stacking
Port Info.
Tag-Based Info.
Management VLAN
User Config
Cable Test
Host Denial-of-Service
Protection
Port Abnormal Traffic
Detection
Firmware Download
Configuration File
Bandwidth Control
Storm Control
Port Mirroring
Trunk Config
Aggregator Setting
LACP Configuration
LACP Link Status
IGMP Menu
IGMP Config
IGMP Groups Status
MVR
MES-2110 Users Guide
55
Chapter 5 The Web Configurator
DHCP Snooping
DHCP Snooping Config
DHCP Binding Table
ARP Inspection
MAC Menu
MAC Table Status
Lock Learning MAC
MAC Filter Config
MAC Limit Config
QoS Menu
Base Configuration
802.1p Priority
Tag Priority
IP DSCP Priority
Priority Override Configuration
The following table describes the links in the navigation panel.
Table 6 Navigation Panel Links
LINK
DESCRIPTION
System Details
System
Info.
This link takes you to a screen that displays general system information.
You can also configure general system information about the MES-2110.
Board Info.
This link takes you to a screen that shows hardware and firmware
information.
DHCP
Config
This link takes you to a screen where you can configure the DHCP
settings.
Configuration
56
Port
Configurati
on
This link takes you to a screen where you can configure settings for
individual MES-2110 ports.
Port Status
This link takes you to a screen that shows port settings for individual
MES-2110 ports.
Rmon
Status
This link takes you to a screen where you can view statistics on the
traffic going through each port.
Loop
Detection
This link takes you to a screen where you can configure protection
against network loops that occur on the edge of your network.
Jumbo
Frame
This link takes you to a screen where you can configure Jumbo frames or
Ethernet frames with a payload greater than 1500 bytes.Use this screen
to configure the jumbo frame size.
802.1x
This link takes you to a screen where you can configure IEEE 802.1x
authentication.
Bridge
Menu
This link takes you to screens where you can configure the RSTP to
prevent network loops.
VLAN Menu
This link takes you to screens where you can configure port-based or
tag-based (802.1Q) VLAN (depending on what you configured in the
Switch Setup menu).
MES-2110 Users Guide
Chapter 5 The Web Configurator
Table 6 Navigation Panel Links (continued)
LINK
DESCRIPTION
Bandwidth
Control
This link takes you to a screen where you can configure bandwidth limits
on the MES-2110.
Storm
Control
This link takes you to a screen to set up broadcast filters.
Port
Mirroring
This link takes you to a screen where you can copy traffic from one port
or ports to another port in order that you can examine the traffic from
the first port without interference.
Trunk
Config
This link takes you to screens where you can logically aggregate physical
links to form one logical, higher-bandwidth link.
IGMP Menu
This link takes you to screens where you can configure various multicast
features, IGMP snooping and create multicast VLANs.
DHCP
Snooping
This link takes you to screens where you can configure filtering of
unauthorized DHCP frames in your network.
ARP
Inspection
This link takes you to a screen where you can configure filtering of
unauthorized Address Resolution Protocol (ARP) frames in your network.
MAC Menu
This link takes you to screens where you can configure the following
settings:
QoS Menu
configure IEEE 802.1x port authentication as well as MAC
authentication for clients communicating via the MES-2110,
activate MAC address learning and set the maximum number of MAC
addresses to learn on a port,
view the MAC addresses (and types) of devices attached to what
ports.
This link takes you to screens where you can configure priority levels for
traffic transmitted through each port.
Mgmt Config
Serial Port
Config
This link takes you to a screen where you can configure the parameters
for connections via the console port.
SNMP
Config
This link takes you to screens where you can configure settings for date
and time.
SNTP
This link takes you to a screen where you can configure SNTP and date/
time settings.
Email
Alarm &
SYSLog
This link takes you to screens where you can set up system logs and email the logs to you.
User Config
This link takes you to a screen where you can set up administrative and
user accounts for people to use the MES-2110.
Cable Test
This link takes you to a screen where you can test the cable connection
on each port.
Host
Denial-ofService
Protection
This link takes you to a screen where you can allow trusted computers to
access the MES-2110 via remote management.
Port
Abnormal
Traffic
Detection
This link takes you to a screen where you can configure the MES-2110 to
detect abnormal traffic transmission and temporarily or permanently
block traffic transmission through a port.
MES-2110 Users Guide
57
Chapter 5 The Web Configurator
Table 6 Navigation Panel Links (continued)
LINK
DESCRIPTION
Firmware
Download
This link takes you to a screen where you can perform firmware
maintenance.
Configurati
on File
This link takes you to a screen where you can perform configuration file
maintenance.
System Restart Menu
Restart
Option
Save Settings
This link takes you to a screen where you can reboot the system.
This link takes you to a screen where you can save the changes you have
made on the MES-2110 and restart the MES-2110.
5.3.1 Set Up the Administrative Password
After you log in for the first time, it is recommended you set up an administrator
password. Click Mgmt Config > User Config to display the next screen. Enter a
password for the admin account and click Apply.
Figure 18 Configure Administrator Login Password
5.4 Saving Your Configuration
When you are done modifying the settings in a screen, click Apply to save your
changes back to the run-time memory. Settings in the run-time memory are lost
when the MES-2110s power is turned off.
Click the Save Settings link in the navigation panel to save your configuration to
nonvolatile memory. Nonvolatile memory refers to the MES-2110s storage that
remains even if the MES-2110s power is turned off. If you don't use Save
Settings all configuration changes will only apply until you restart the MES-2110.
Note: Use the Save Settings link when you are done with a configuration session.
Note: After saving changes to the IP Address, Subnet Mask or Gateway settings, the
MES-2110 will need to reboot to put them into effect (after prompting you for
confirmation.)
58
MES-2110 Users Guide
Chapter 5 The Web Configurator
5.5 Switch Lockout
You could block yourself (and all others) from using in-band-management
(managing through the data ports) if you do one of the following:
1
Delete the management VLAN (default is VLAN 1).
Delete all port-based VLANs with the CPU port as a member. The CPU port is the
management port of the MES-2110.
Filter all traffic to the CPU port.
Disable all ports.
Misconfigure the text configuration file.
Forget the password and/or IP address.
Prevent all services from accessing the MES-2110.
Change a service port number but forget it.
Note: Be careful not to lock yourself and others out of the MES-2110. If you do lock
yourself out, try using out-of-band management (via the console port) to
configure the MES-2110.
5.6 Resetting the MES-2110
If you lock yourself (and others) from the MES-2110 or forget the administrator
password, you will need to reload the factory-default configuration file or reset the
MES-2110 back to the factory defaults.
5.6.1 Reload the Configuration File
Uploading the factory-default configuration file replaces the current configuration
file with the factory-default configuration file. This means that you will lose all
previous configurations and the speed of the console port will be reset to the
default of 9600 bps with 8 data bits, no parity, one stop bit and flow control set to
none. The password will also be cleared and the IP address be set to
192.168.0.254.
To upload the configuration file, do the following:
1
Connect to the console port using a computer with terminal emulation software.
MES-2110 Users Guide
59
Chapter 5 The Web Configurator
Disconnect and reconnect the MES-2110s power to begin a session. When you
reconnect the MES-2110s power, you will see the initial screen.
When you see Username:, type admin and press [Enter].
Type the administrative password and press [Enter]. Simply press [Enter] if you
did not set up a password.
Type enable and press [Enter] to turn on administrative commands.
Type reset default and press [Enter] to restore the system to the factory
defaults. The MES-2110 will restart.
Figure 19 Resetting the MES-2110: Via the Console Port
Username: admin
Password:
MES-2110> enable
MES-2110# reset default
The MES-2110 is now reinitialized with a default configuration file.
60
MES-2110 Users Guide
CHAPTER
System Details
6.1 Overview
The System Details screens show general system information about the MES2110. You can also use the screens to configure system and DHCP client settings.
6.2 The System Information Screen
Click System Details > System Info. to open the following screen.
Figure 20 System Details > System Info.
MES-2110 Users Guide
61
Chapter 6 System Details
The following table describes the labels in this screen.
Table 7 System Details > System Info.
LABEL
DESCRIPTION
Description
This is the descriptive name of the MES-2110 for identification
purposes.
Model Name
This is the model name of the MES-2110.
Object ID
An Object ID defines what trap the MES-2110 should send an
SNMP Manager.
Up Time
This shows how long the MES-2110 has been turned on.
System Name
Choose a descriptive name for identification purposes. This name
consists of up to 64 printable characters; spaces are allowed.
Contact Name
Enter the name of the person in charge of this MES-2110. You can
use up to 32 printable ASCII characters; spaces are allowed.
Location
Enter the geographic location of your MES-2110. You can use up
to 32 printable ASCII characters; spaces are allowed.
DHCP Client
This shows whether the DHCP client is Enabled or Disabled. If
DHCP is disabled, you must enter an IP address, subnet mask and
gateway in the following fields. Otherwise, a DHCP server will
assign this information to the MES-2110.
See Section 6.4 on page 63 for details about configuring the
DHCP client.
IP Address
Enter the IP address of your MES-2110 in dotted decimal notation
for example 192.168.1.1.
Subnet Mask
Enter the IP subnet mask of your MES-2110 in dotted decimal
notation for example 255.255.255.0.
Gateway
Enter the IP address of the default outgoing gateway in dotted
decimal notation, for example 192.168.1.254.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
6.3 The Board Information Screen
Use this screen to view the hardware and firmware information. Click System
Details > Board Info. to open the following screen.
Figure 21 System Details > Board Info.
62
MES-2110 Users Guide
Chapter 6 System Details
The following table describes the labels in this screen.
Table 8 System Details > Board Info.
LABEL
DESCRIPTION
Hardware Version
This is the version number of the MES-2110s hardware.
Firmware Version
This is the version number of the MES-2110s current firmware
including the date and time that the firmware is created.
Port Number
This shows the number of available ports on the MES-2110.
6.4 The DHCP Configuration Screen
Use this screen to turn on or off the DHCP client. Click System Details > DHCP
Config to open the following screen.
Figure 22 System Details > DHCP Config
The following table describes the labels in this screen.
Table 9 System Details > DHCP Config
LABEL
DESCRIPTION
DHCP Client
Use this to turn the DHCP client on or off. Turn on the DHCP client
if you have a DHCP server that can assign the MES-2110 an IP
address, subnet mask and a default gateway IP address
automatically.
DHCP Client State
This shows whether the DHCP client is Enabled or Disabled.
DHCP Leased Time
This is how long ago the MES-2110 got an IP address from a
DHCP server (if DHCP client is enabled).
DHCP Expiry Time
This is how long there is to go before the MES-2110 will get a new
IP address from a DHCP server (if DHCP client is enabled).
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
63
Chapter 6 System Details
Once you click the Apply button, the following message displays, reminding you
to save your settings in the Save Settings screen and reboot the MES-2110.
Figure 23 System Details > DHCP Config > Apply
64
MES-2110 Users Guide
CHAPTER
Configuration
7.1 Overview
The Configuration screens let you configure the MES-2110 settings.
7.2 The Port Configuration Screen
Use this screen to configure MES-2110 port settings. You can assign a unique
name to the ports, select its speed setting and enable or disable auto-negotiation.
Click Configuration > Port Configuration to open the following screen.
Figure 24 Configuration > Port Configuration
MES-2110 Users Guide
65
Chapter 7 Configuration
The following table describes the labels in this screen.
Table 10 Configuration > Port Configuration
LABEL
DESCRIPTION
Port
This is the port number.
Name
Enter a descriptive name that identifies this port. You can enter
up to 64 alpha-numerical characters.
Note: Due to space limitation, the port name may be
truncated in some Web Configurator screens.
Admin
Use this to enable or disable administrative access through this
port.
Speed
Select the ports current speed (10M for 10 Mbps and 100M for
100 Mbps). The speed for the fiber ports is fixed.
Duplex
Use this field to change the status to Half or Full duplex mode.
The duplex status for the fiber ports is fixed.
AUTO
Use this to enable or disable auto-negotiation.
AUTO (auto-negotiation) allows one port to negotiate with a peer
port automatically to obtain the connection speed and duplex
mode that both ends support. When auto-negotiation is turned
on, a port on the MES-2110 negotiates with the peer
automatically to determine the connection speed and duplex
mode. If the peer port does not support auto-negotiation or turns
off this feature, the MES-2110 determines the connection speed
by detecting the signal on the cable and using half duplex mode.
When the MES-2110s auto-negotiation is turned off, a port uses
the pre-configured speed and duplex mode when making a
connection, thus requiring you to make sure that the settings of
the peer port are the same in order to connect.
Flow-Control
Use this to enable or disable flow control.
A concentration of traffic on a port decreases port bandwidth and
overflows buffer memory causing frame discards and frame
losses. Flow Control is used to regulate transmission of signals
to match the bandwidth of the receiving port.
The MES-2110 uses IEEE802.3x flow control in full duplex mode
and backpressure flow control in half duplex mode.
IEEE802.3x flow control is used in full duplex mode to send a
pause signal to the sending port, causing it to temporarily stop
sending signals when the receiving port memory buffers fill.
Back Pressure flow control is typically used in half duplex mode to
send a "collision" signal to the sending port (mimicking a state of
frame collision) causing the sending port to temporarily stop
sending signals and resend later.
66
Port
This indicates the port number
Name
This indicates the descriptive named assigned to the port.
Admin
This indicates whether administrative access is enabled or
disabled for this port.
Speed
This indicates the speed assigned to the port (10M for 10 Mbps
and 100M for 100 Mbps).
MES-2110 Users Guide
Chapter 7 Configuration
Table 10 Configuration > Port Configuration
LABEL
DESCRIPTION
Duplex
This indicates the ports duplex mode (Half or Full).
AUTO
This indicates whether auto-negotiation for this port is enabled or
disabled.
Flow-Control
This indicates whether flow control for this port is enabled or
disabled.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
7.3 The Port Status Screen
To view the port statistics, click Configuration > Port Status to display the
Status screen as shown next.
Figure 25 Configuration > Port Status
The following table describes the labels in this screen.
Table 11 Configuration > Port Status
LABEL
DESCRIPTION
Port
This identifies the Ethernet port.
Name
This is the name you assigned to this port in the Configuration > Port
Configuration screen.
Type
This is the type of connector for each port. Port 1-8 are RJ-45 ports for
Ethernet connections. Port 9-10 are Gigabit SFP ports for fiber
connections.
Admin
This shows whether administrative access is Enabled or Disabled on the
port. When administrative access is disabled on the port, users cannot
manage the MES-2110 via that port.
MES-2110 Users Guide
67
Chapter 7 Configuration
Table 11 Configuration > Port Status (continued)
LABEL
DESCRIPTION
Speed
This is the ports current speed (10M for 10 Mbps and 100M for 100
Mbps).
Duplex
This is the the ports duplex status (Half or Full).
Link
This shows the ports connection status.
AUTO
This shows whether auto-negotiation is On or Off.
Flow-Control
This shows whether flow control is Enabled or Disabled.
Port
Configuration
Click this to configure port settings in the Port Configuration screen.
7.4 The RMON Status Screen
Use this screen to view individual port statistics. Click Configuration > Rmon
Status to open the following screen.
Figure 26 Configuration > Rmon Status
The following table describes the labels in this screen.
Table 12 Configuration > Rmon Status
68
LABEL
DESCRIPTION
Slot Number
Use this to select the port number you are viewing.
Clear
Click this to reset the statistics on this port to zero.
MES-2110 Users Guide
Chapter 7 Configuration
Table 12 Configuration > Rmon Status (continued)
LABEL
DESCRIPTION
RX
The following fields show detailed information about frames received.
InUnicasts
This field shows the number of good unicast frames received.
InBroadcasts
This field shows the number of good broadcast frames received.
InPause
This field shows the number of 802.3x Pause frames received.
InMulticasts
This field shows the number of good multicast frames received.
InGoodOctetsHi
This field shows the number of good upper octet frames received.
InGoodOctetsLo
This field shows the number of good lower octet frames received.
InFCSErr
This field shows the number of frames received with Cyclic
Redundant Check (CRC) error(s).
InMACRcvErr
This field shows the number of frames received with an RxErr signal
from the PHY.
InBadOctets
This field shows the number of bad octet frames received.
InUndersize
This field shows the number of frames received that were too short
(shorter than 64 octets).
InFragments
This field shows the number of frames received that were too short
(shorter than 64 octets) and were received with with Cyclical
Redundancy Check (CRC) errors.
InJabber
This field shows the number of frames received with a length that
exceeds the maximum octet size and were received with CRC errors.
InOversize
This field shows the number of frames received with a length that
was out of range.
TX
The following fields show detailed information about frames transmitted.
OutUnicasts
This field shows the number of good unicast frames transmitted.
OutBroadcasts
This field shows the number of good broadcast frames transmitted.
Late
This is the number of times a late collision is detected, that is, after
512 bits of the frames have already been transmitted.
Excessive
This is a count of frames for which transmission failed due to
excessive collisions. Excessive collision is defined as the number of
maximum collisions before the retransmission count is reset.
Multiple
This is a count of successfully transmitted frames for which
transmission was inhibited by more than one collision.
Single
This is a count of successfully transmitted frames for which
transmission is inhibited by exactly one collision.
Deferred
This is a count of frames for which transmission delayed due to busy
traffic. The deferred frames are waiting to be transmitted from the
MES-2110 buffer. This counter only works for the half-duplex mode.
RX+TX
64 Octets
This field shows the number of frames (including bad frames)
received that were 64 octets in length.
65to127 Octets
This field shows the number of frames (including bad frames)
received that were between 65 and 127 octets in length.
MES-2110 Users Guide
69
Chapter 7 Configuration
Table 12 Configuration > Rmon Status (continued)
70
LABEL
DESCRIPTION
128to255 Octets
This field shows the number of frames (including bad frames)
received that were between 128 and 255 octets in length.
256to511 Octets
This field shows the number of frames (including bad frames)
received that were between 256 and 511 octets in length.
512to1023 Octets
This field shows the number of frames (including bad frames)
received that were between 512 and 1023 octets in length.
1024toMax Octets
This field shows the number of frames (including bad frames)
received that were between 1024 and the maximum octets in length.
MES-2110 Users Guide
CHAPTER
Loop Detection
8.1 Overview
Loop detection allows you to configure the MES-2110 to shut down a port if it
detects that frames sent out on that port loop back to the MES-2110.
Loop detection is designed to handle loop problems on the edge of your network.
This can occur when a port is connected to a MES-2110 that is in a loop state.
Loop state occurs as a result of human error. It happens when two ports on a
switch are connected with the same cable. When a switch in loop state sends out
broadcast messages the messages loop back to the switch and are re-broadcast
again and again causing a broadcast storm.
If a switch (not in loop state) connects to a switch in loop state, then it will be
affected by the switch in loop state in the following way:
It will receive broadcast messages sent out from the switch in loop state.
It will receive its own broadcast messages that it sends out as they loop back. It
will then re-broadcast those messages again.
The following figure shows port N on switch A connected to switch B. Switch B is
in loop state. When broadcast or multicast frames leave port N and reach switch
B, they are sent back to port N on A as they are rebroadcast from B.
Figure 27 Switch in Loop State
N
The loop detection feature checks to see if a loop detection enabled port is
connected to a switch in loop state. This is accomplished by periodically sending a
probe frame and seeing if the frame returns on the same port. If this is the case,
the MES-2110 will shut down the port connected to the switch in loop state.
MES-2110 Users Guide
71
Chapter 8 Loop Detection
The following figure shows a loop detection enabled port N on switch A sending a
probe frame P to switch B. Since switch B is in loop state, the probe frame P
returns to port N on A. The MES-2110 then shuts down port N to ensure that the
rest of the network is not affected by the switch in loop state.
Figure 28 Loop detection - Probe Frame
P
N
Note: After resolving the loop problem on your network you can re-activate the
disabled port via the web configurator or via commands (See the CLI Reference
Guide).
8.2 The Loop Detection Screen
Click Configuration > Loop Detection to open the following screen.
Figure 29 Configuration > Loop Detection
72
MES-2110 Users Guide
Chapter 8 Loop Detection
The following table describes the labels in this screen.
Table 13 Configuration > Loop Detection
LABEL
DESCRIPTION
Protection
Select Enable or Disable to have the MES-2110 apply loop
detection.
The MES-2110 generates syslog, internal log messages as well as
SNMP traps when it shuts down a port via the loop detection
feature.
MAC Address
This is the MAC address of the probe frame sent by the MES2110. You can configure the field as a unicast or multicast MAC
address, depending on your needs.
The default MAC address is a multicast address
(01.01.02.02.03.03). Some network switch does not forward
frames with unrecognized multicast MAC address. Test frames
sent out for loop detection will be discarded by this type of switch.
Users can configure a unicast MAC address to solve this problem.
Port
This is the port number.
Enable/Disable
Select Enable or Disable to have the MES-2110 apply loop
detection feature on this port. When the loop detection feature is
enabled, the MES-2110 sends probe frames from this port to
check if the switch it is connected to is in loop state. If the switch
that this port is connected is in loop state the MES-2110 will shut
down this port.
Block/Unblock
When the MES-2110 detects looping, the system sets the port to
Block. Use this field to Unblock the port once you have manually
fixed the loop.
Undo
Click this to restore your last saved settings.
Refresh
Click this to reset the data for the field(s).
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
73
Chapter 8 Loop Detection
74
MES-2110 Users Guide
CHAPTER
Jumbo Frame
9.1 Overview
Jumbo frames are Ethernet frames with a payload greater than 1500 bytes. Jumbo
frames can enhance data transmission efficiency in a Gigabit network.
9.2 The Jumbo Frame Configuration Screen
Use this screen to configure the jumbo frame size. Click Configuration > Jumbo
Frame to open the following screen.
Figure 30 Configuration > Jumbo Frame
The following table describes the labels in this screen.
Table 14 Configuration > Jumbo Frame
LABEL
DESCRIPTION
Frame Size
Configure the jumbo frame size (1522 to 1632). The bigger the
frame size, the better the performance.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
75
Chapter 9 Jumbo Frame
76
MES-2110 Users Guide
CHAPTER
10
802.1x
10.1 Overview
This chapter describes the IEEE 802.1x authentication method.
Port authentication is a way to validate access to ports on the MES-2110 to clients
based on an external server (authentication server). The MES-2110 supports the
following method for port authentication:
IEEE 802.1x1 - An authentication server validates access to a port based on a
username and password provided by the user.
IEEE 802.1x authentication uses the RADIUS (Remote Authentication Dial In User
Service, RFC 2138, 2139) protocol to validate users. See Section 10.6 on page 84
for more information on configuring your RADIUS server settings.
10.1.1 IEEE 802.1x Authentication
The following figure illustrates how a client connecting to a IEEE 802.1x
authentication enabled port goes through a validation process. The MES-2110
prompts the client for login information in the form of a user name and password.
When the client provides the login credentials, the MES-2110 sends an
1.
At the time of writing, IEEE 802.1x is not supported by all operating systems. See your operating system
documentation. If your operating system does not support 802.1x, then you may need to install 802.1x client
software.
MES-2110 Users Guide
77
Chapter 10 802.1x
authentication request to a RADIUS server. The RADIUS server validates whether
this client is allowed access to the port.
Figure 31 IEEE 802.1x Authentication Process
1
New Connection
2
Login Info Request
3
Login Credentials
4
Authentication Request
5
Authentication Reply
Session Granted/Denied
10.1.2 Guest VLAN
When 802.1x port authentication is enabled on the MES-2110, clients that do not
have the correct credentials are blocked from using the port(s). You can configure
your MES-2110 to have one Guest VLAN. Traffic coming from the Guest VLAN are
directed to the Guest network and can have access to unrestricted areas of the
network, such as the Internet. The rights granted to the Guest VLAN depends on
how the network administrator configures switches or routers with the Guest
network feature.
Note: Use the MES-2110 to assign the Guest VLAN to a port. This assignment should
corresponds to the networks Guest VLAN. The Guest network is not
configurable in this MES-2110.
To enable port authentication, first activate the port authentication method (both
on the MES-2110 and the port(s)) then configure the RADIUS server settings in
the Radius Server Configuration screen (Section 10.4 on page 81).
78
MES-2110 Users Guide
Chapter 10 802.1x
10.2 802.1x Global Configuration Screen
Use this screen to enable port authentication and a guest VLAN on the MES-2110.
Click Configuration > 802.1x > Global Configuration in the navigation panel
to display the screen as shown.
Figure 32 Configuration > Global Configuration
The following table describes the labels in this screen.
Table 15 Configuration > Global Configuration
LABEL
DESCRIPTION
802.1x
Select Enable to activate the port authentication method on the
MES-2110. Otherwise, select Disable.
Reauth-Max
Specify the number of times the MES-2110 tries to authenticate client(s)
before sending unresponsive ports to the Guest VLAN.
This is set to 2 by default. That is, the MES-2110 attempts to
authenticate a client twice. If the client does not respond to the
first authentication request, the MES-2110 tries again. If the client
still does not respond to the second request, the MES-2110 sends
the client to the Guest VLAN. The client needs to send a new
request to be authenticated by the MES-2110 again.
Guest VLAN
Select Enable then enter the number that identifies the Guest VLAN.
Make sure this is the Guest VLAN recognized in your network.
Clients belonging to the guest VLAN can access unprotected areas in your
network, such as the Internet.
Select Disable if you do not want to use this feature.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory.
The MES-2110 loses these changes if it is turned off or loses power, so
use the Save Settings link in the navigation panel to save your changes
to the non-volatile memory when you are done configuring.
MES-2110 Users Guide
79
Chapter 10 802.1x
10.3 802.1x Radius Server Configuration Screen
Use this screen to configure the RADIUS server settings.
Click Configuration > 802.1x > Radius Server Configuration in the
navigation panel to display the screen as shown.
Figure 33 Configuration > Radius Server Configuration
The following table describes the labels in this screen.
Table 16 Configuration > Radius Server Configuration
80
LABEL
DESCRIPTION
Server IP
Address
Enter the IP address of the external authentication server in dotted
decimal notation.
Server
Shared Key
Enter a password (up to 128 alphanumeric characters) as the key to be
shared between the external authentication server and the MES-2110.
The key must be the same on the external authentication server and your
MES-2110. The key is not sent over the network.
Server UDP
Port Number
Enter the port number of the RADIUS server. The default port number is
1812.
Server
Accounting
Port Number
Enter the port number of the external accounting server. The default port
number is 1813. You need not change this value unless your network
administrator instructs you to do so with additional information.
Server Time
Out
Type how many minutes a session can be left idle before the session
times out.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory.
The MES-2110 loses these changes if it is turned off or loses power, so
use the Save Settings link in the navigation panel to save your changes
to the non-volatile memory when you are done configuring.
MES-2110 Users Guide
Chapter 10 802.1x
10.4 802.1x Port Configuration Screen
Use this screen to enable and configure port authentication on individual ports.
Click Configuration > 802.1x > Port Configuration in the navigation panel to
display the screen as shown.
Figure 34 Configuration > Port Configuration
The following table describes the labels in this screen.
Table 17 Configuration > Port Configuration
LABEL
DESCRIPTION
Port
Select a port number to configure.
Active
Enable this to permit 802.1x authentication on the MES-2110.
Note: You must first enable 802.1x authentication on the MES-2110
before configuring it on each port.
MES-2110 Users Guide
81
Chapter 10 802.1x
Table 17 Configuration > Port Configuration (continued)
LABEL
DESCRIPTION
Guest VLAN
You can configure this if you have enabled the guest VLAN feature in the
Configuration > Global Configuration screen (see Section 10.2 on
page 79).
Select Enable then enter the number that identifies the Guest VLAN.
Make sure this is the Guest VLAN recognized in your network.
Clients belonging to the guest VLAN can access unprotected areas in your
network, such as the Internet.
Select Disable if you do not want to use this feature.
Reauthenticat
ion
Enable this if a subscriber has to periodically re-enter his or her username
and password to stay connected to the port.
Reauth-Period Specify how often (in minutes) a client has to re-enter his or her
(1-999999)
username and password to stay connected to the port.
Default is 3600 minutes (or 1 hour).
Port
This indicates the port number.
Active
This indicates whether 802.1x authentication is enabled or disabled for
this port.
Guest VLAN
This indicates whether Guest VLAN is enabled or disabled for this port.
Reauthenticat
ion
This indicates whether Reauthentication is enabled or disabled for
this port.
Reauth-Period This indicates the Reauth-Period for the this port.
(1-999999)
82
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory.
The MES-2110 loses these changes if it is turned off or loses power, so
use the Save Settings link in the navigation panel to save your changes
to the non-volatile memory when you are done configuring.
MES-2110 Users Guide
Chapter 10 802.1x
10.5 802.1x Radius Server Configuration Screen
Use this screen to view a summary of port authentication settings on the MES2110 and in each individual ports.
Click Configuration > 802.1x > 802.1x Status in the navigation panel to
display the screen as shown.
Figure 35 Configuration > 802.1x Status
The following table describes the labels in this screen.
Table 18 Configuration > 802.1x Status
LABEL
DESCRIPTION
802.1x
This shows if port authentication is enabled on the MES-2110.
Guest VLAN
This shows if a Guest VLAN is enabled on the Switch.
Reauth-Max
This shows the number of times the MES-2110 attempts to authenticate
clients for port access.
Server IP
Address
This is the IP address of the RADIUS server.
Server
Shared Key
This is the password shared between the external authentication server
and the MES-2110.
Server UDP
Port Number
This is the port number of the RADIUS server.
Server
Accounting
Port Number
This is the port number of the external accounting server.
Server TimeOut
This shows how many minutes a session can be idle before the session
times out.
When a session times out, the client has to send a new request to the
server and be authenticated again.
The table below describes the settings for ports 1-10
Active
MES-2110 Users Guide
This shows if port authentication is enabled on the port.
83
Chapter 10 802.1x
Table 18 Configuration > 802.1x Status (continued)
LABEL
DESCRIPTION
Guest VLAN
This shows if a Guest VLAN is enabled on the port.
Reauthenticat
ion
This shows if a subscriber has to periodically re-enter his or her username
and password to stay connected to the port.
Reauth-Period This shows how often (in minutes) a client has to re-enter his or her
username and password to stay connected to the port.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory.
The MES-2110 loses these changes if it is turned off or loses power, so
use the Save Settings link in the navigation panel to save your changes
to the non-volatile memory when you are done configuring.
10.6 Technical Reference
This section provides technical background information about the topics covered in
this chapter.
10.6.1 RADIUS and TACACS+
RADIUS and TACACS+ are security protocols used to authenticate users by means
of an external server instead of (or in addition to) an internal device user database
that is limited to the memory capacity of the device. In essence, RADIUS and
TACACS+ authentication both allow you to validate an unlimited number of users
from a central location.
The following table describes some key differences between RADIUS and
TACACS+.
Table 19 RADIUS vs. TACACS+
RADIUS
TACACS+
Transport
Protocol
UDP (User Datagram Protocol)
TCP (Transmission Control Protocol)
Encryption
Encrypts the password sent for
authentication.
All communication between the client
(the MES-2110) and the TACACS
server is encrypted.
10.6.2 Supported RADIUS Attributes
Remote Authentication Dial-In User Service (RADIUS) attributes are data used to
define specific authentication, and accounting elements in a user profile, which is
stored on the RADIUS server. This appendix lists the RADIUS attributes supported
by the MES-2110.
84
MES-2110 Users Guide
Chapter 10 802.1x
Refer to RFC 2865 for more information about RADIUS attributes used for
authentication. Refer to RFC 2866 and RFC 2869 for RADIUS attributes used for
accounting.
This section lists the attributes used by authentication and accounting functions on
the MES-2110. In cases where the attribute has a specific format associated with
it, the format is specified.
10.6.3 Attributes Used for Authentication
The following sections list the attributes sent from the MES-2110 to the RADIUS
server when performing authentication.
10.6.3.1 Attributes Used for Authenticating Privilege Access
User-Name
- The format of the User-Name attribute is $enab#$, where # is the privilege
level (1-14).
User-Password
NAS-Identifier
NAS-IP-Address
10.6.3.2 Attributes Used to Login Users
User-Name
User-Password
NAS-Identifier
NAS-IP-Address
10.6.3.3 Attributes Used by the IEEE 802.1x Authentication
User-Name
NAS-Identifier
NAS-IP-Address
NAS-Port
NAS-Port-Type
- This value is set to Ethernet(15) on the MES-2110.
Calling-Station-Id
Frame-MTU
EAP-Message
State
Message-Authenticator
MES-2110 Users Guide
85
Chapter 10 802.1x
10.6.4 Attributes Used for Accounting
The following sections list the attributes sent from the MES-2110 to the RADIUS
server when performing authentication.
10.6.4.1 Attributes Used for Accounting System Events
NAS-IP-Address
NAS-Identifier
Acct-Status-Type
Acct-Session-ID
- The format of Acct-Session-Id is date+time+8-digit sequential number,
for example, 2007041917210300000001. (date: 2007/04/19, time:
17:21:03, serial number: 00000001)
Acct-Delay-Time
10.6.4.2 Attributes Used for Accounting Exec Events
The attributes are listed in the following table along with the time that they are
sent (the difference between Console and Telnet/SSH Exec events is that the
Telnet/SSH events utilize the Calling-Station-Id attribute):
Table 20 RADIUS Attributes - Exec Events via Console
ATTRIBUTE
START
INTERIM-UPDATE
STOP
User-Name
NAS-Identifier
NAS-IP-Address
Service-Type
Acct-Status-Type
Acct-Delay-Time
Acct-Session-Id
Acct-Authentic
Acct-Session-Time
Acct-Terminate-Cause
Table 21 RADIUS Attributes - Exec Events via Telnet/SSH
ATTRIBUTE
86
START
INTERIM-UPDATE
STOP
User-Name
NAS-Identifier
NAS-IP-Address
Service-Type
Calling-Station-Id
Acct-Status-Type
Acct-Delay-Time
MES-2110 Users Guide
Chapter 10 802.1x
Table 21 RADIUS Attributes - Exec Events via Telnet/SSH
ATTRIBUTE
START
INTERIM-UPDATE
STOP
Acct-Session-Id
Acct-Authentic
Acct-Session-Time
Acct-Terminate-Cause
10.6.4.3 Attributes Used for Accounting IEEE 802.1x Events
The attributes are listed in the following table along with the time of the session
they are sent:
Table 22 RADIUS Attributes-Exec Events via 802.1x
ATTRIBUTE
START
INTERIM-UPDATE
STOP
User-Name
NAS-IP-Address
NAS-Port
Class
Called-Station-Id
Calling-Station-Id
NAS-Identifier
NAS-Port-Type
Acct-Status-Type
Acct-Delay-Time
Acct-Session-Id
Acct-Authentic
Acct-Input-Octets
Acct-Output-Octets
Acct-Session-Time
Acct-Input-Packets
Acct-Output-Packets
Acct-Terminate-Cause
Acct-Input-Gigawords
Acct-OutputGigawords
MES-2110 Users Guide
87
Chapter 10 802.1x
88
MES-2110 Users Guide
CHAPTER
11
Bridge
11.1 Overview
The MES-2110 supports Rapid Spanning Tree Protocol (RSTP) as defined in the
IEEE 802.1w Rapid Spanning Tree Protocol standard.
(R)STP detects and breaks network loops and provides backup links between
switches, bridges or routers. It allows a switch to interact with other (R)STP compliant switches in your network to ensure that only one path exists between
any two stations on the network.
The MES-2110 uses IEEE 802.1w RSTP (Rapid Spanning Tree Protocol) that allows
faster convergence of the spanning tree than STP (while also being backwards
compatible with STP-only aware bridges). In RSTP, topology change information is
directly propagated throughout the network from the device that generates the
topology change. In STP, a longer delay is required as the device that causes a
topology change first notifies the root bridge that then notifies the network. Both
RSTP and STP flush unwanted learned addresses from the filtering database. In
RSTP, the port states are Discarding, Learning, and Forwarding.
Note: In this users guide, STP refers to both STP and RSTP.
11.1.1 STP Terminology
The root bridge is the base of the spanning tree.
Path cost is the cost of transmitting a frame onto a LAN through that port. The
recommended cost is assigned according to the speed of the link to which a port is
attached. The slower the media, the higher the cost.
Table 23 STP Path Costs
LINK
SPEED
RECOMMENDED
VALUE
RECOMMENDED
RANGE
ALLOWED
RANGE
Path
Cost
4Mbps
250
100 to 1000
1 to 65535
Path
Cost
10Mbps
100
50 to 600
1 to 65535
MES-2110 Users Guide
89
Chapter 11 Bridge
Table 23 STP Path Costs
LINK
SPEED
RECOMMENDED
VALUE
RECOMMENDED
RANGE
ALLOWED
RANGE
Path
Cost
16Mbps
62
40 to 400
1 to 65535
Path
Cost
100Mbps
19
10 to 60
1 to 65535
Path
Cost
1Gbps
3 to 10
1 to 65535
Path
Cost
10Gbps
1 to 5
1 to 65535
On each bridge, the root port is the port through which this bridge communicates
with the root. It is the port on this switch with the lowest path cost to the root (the
root path cost). If there is no root port, then this switch has been accepted as the
root bridge of the spanning tree network.
For each LAN segment, a designated bridge is selected. This bridge has the lowest
cost to the root among the bridges connected to the LAN.
11.1.2 How STP Works
After a bridge determines the lowest cost-spanning tree with STP, it enables the
root port and the ports that are the designated ports for connected LANs, and
disables all other ports that participate in STP. Network frames are therefore only
forwarded between enabled ports, eliminating any possible network loops.
STP-aware switches exchange Bridge Protocol Data Units (BPDUs) periodically.
When the bridged LAN topology changes, a new spanning tree is constructed.
Once a stable network topology has been established, all bridges listen for Hello
BPDUs (Bridge Protocol Data Units) transmitted from the root bridge. If a bridge
does not get a Hello BPDU after a predefined interval (Max Age), the bridge
assumes that the link to the root bridge is down. This bridge then initiates
negotiations with other bridges to reconfigure the network to re-establish a valid
network topology.
90
MES-2110 Users Guide
Chapter 11 Bridge
11.1.3 STP Port States
STP assigns five port states to eliminate frame looping. A bridge port is not
allowed to go directly from blocking state to forwarding state so as to eliminate
transient loops.
Table 24 STP Port States
PORT
STATE
DESCRIPTION
Disabled
STP is disabled (default).
Blocking
Only configuration and management BPDUs are received and processed.
Listening
All BPDUs are received and processed.
Note: The listening state does not exist in RSTP.
Learning
All BPDUs are received and processed. Information frames are submitted
to the learning process but not forwarded.
Forwarding
All BPDUs are received and processed. All information frames are received
and forwarded.
11.2 The Bridge Configuration Screen
Click Configuration > Bridge Menu > Bridge Config to open the following
screen.
Figure 36 Configuration > Bridge Menu > Bridge Config
MES-2110 Users Guide
91
Chapter 11 Bridge
The following table describes the labels in this screen.
Table 25 Configuration > Bridge Menu > Bridge Config
LABEL
DESCRIPTION
Ring Protocol
Select RSTP (802.1W) to enable RSTP.
Select Disable if you do not want to use this feature.
Port
Select Enable to have the port participate in RSTP when you
select RSTP (802.1W) in the Ring Protocol field.
Select Disable so that the port will not participate in RSTP when
you select RSTP (802.1W) in the Ring Protocol field.
Select Tunnel so that the port will not participate in RSTP. When
the tunnel port receives Bridge Protocol Data Units (BPDU)
frames, the MES-2110 forwards the frames to other tunnel ports.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
11.3 The RSTP System Configuration Screen
You must first enable RSTP in the Bridge Configuration screen in order to open
this screen.
Click Configuration > Bridge Menu > RSTP System Config to open the
following screen.
Figure 37 Configuration > Bridge Menu > RSTP System Config
92
MES-2110 Users Guide
Chapter 11 Bridge
The following table describes the labels in this screen.
Table 26 Configuration > Bridge Menu > RSTP System Config
LABEL
DESCRIPTION
Root Bridge Information
Bridge Priority
Bridge priority is used in determining the root switch, root port
and designated port. The switch with the highest priority (lowest
numeric value) becomes the STP root switch. If all switches have
the same priority, the switch with the lowest MAC address will
then become the root switch. Select a value from the drop-down
list box.
The lower the numeric value you assign, the higher the priority
for this bridge.
Bridge Priority determines the root bridge, which in turn
determines Hello Time, Max Age and Forwarding Delay.
MAC Address
This is the root bridges MAC address.
Root Path Cost
Path cost is the cost of transmitting a frame on to a LAN through
that port. It is recommended to assign this value according to the
speed of the bridge. The slower the media, the higher the costsee Table 23 on page 89 for more information.
Root Port
This shows whether the MES-2110 connects to another root
switch (through port number 1-10) or serves as a root switch
(Root).
Hello Time (sec)
This is the time interval (in seconds) at which the root switch
transmits a configuration message. The root bridge determines
Hello Time, Max Age and Forwarding Delay.
Forward Delay (sec)
This is the time (in seconds) the root switch will wait before
changing states (that is, listening to learning to forwarding).
Note: The listening state does not exist in RSTP.
Max age (sec)
This is the maximum time (in seconds) the MES-2110 can wait
without receiving a configuration message before attempting to
reconfigure.
Configuration Spanning Tree Parameters
RSTP Force Version
Use this to force the spanning tree algorithm to run on either the
STP or RSTP protocol.
Bridge Priority
Bridge priority is used in determining the root switch, root port
and designated port. The switch with the highest priority (lowest
numeric value) becomes the STP root switch. If all switches have
the same priority, the switch with the lowest MAC address will
then become the root switch. Select a value from the drop-down
list box.
The lower the numeric value you assign, the higher the priority
for this bridge.
Bridge Priority determines the root bridge, which in turn
determines Hello Time, Max Age and Forwarding Delay.
Hello Time (sec)
MES-2110 Users Guide
This is the time interval in seconds between BPDU (Bridge
Protocol Data Units) configuration message generations by the
root switch. The allowed range is 1 to 10 seconds.
93
Chapter 11 Bridge
Table 26 Configuration > Bridge Menu > RSTP System Config
LABEL
DESCRIPTION
Forward Delay (sec)
This is the maximum time (in seconds) the MES-2110 will wait
before changing states. This delay is required because every
switch must receive information about topology changes before it
starts to forward frames. In addition, each port needs time to
listen for conflicting information that would make it return to a
blocking state; otherwise, temporary data loops might result. The
allowed range is 4 to 30 seconds.
As a general rule:
Note: 2 * (Forward Delay - 1) >= Max Age >= 2 * (Hello Time
+ 1)
94
Max age (sec)
This is the maximum time (in seconds) the MES-2110 can wait
without receiving a BPDU before attempting to reconfigure. All
MES-2110 ports (except for designated ports) should receive
BPDUs at regular intervals. Any port that ages out STP
information (provided in the last BPDU) becomes the designated
port for the attached LAN. If it is a root port, a new root port is
selected from among the MES-2110 ports attached to the
network. The allowed range is 6 to 40 seconds.
Undo
Click this to restore your last saved settings.
Refresh
Click this to reset the data for the field(s).
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
MES-2110 Users Guide
Chapter 11 Bridge
11.4 The Spanning Tree Port Configuration
Click Configuration > Bridge Menu > RSTP Per Port Config to open the
following screen.
Figure 38 Configuration > Bridge Menu > RSTP Per Port Config
The following table describes the labels in this screen.
Table 27 Configuration > Bridge Menu > RSTP Per Port Config
LABEL
DESCRIPTION
Port
Select a port to configure.
Priority (1~255)
Enter the ports priority rating.
Priority decides which port should be disabled when more than
one port forms a loop in a switch. Ports with a higher priority
numeric value are disabled first. The allowed range is between 0
and 255 and the default value is 128.
Cost (1~65535)
Enter the ports path cost.
Path cost is the cost of transmitting a frame on to a LAN through
that port. It is recommended to assign this value according to the
speed of the bridge. The slower the media, the higher the costsee Table 23 on page 89 for more information.
MES-2110 Users Guide
95
Chapter 11 Bridge
Table 27 Configuration > Bridge Menu > RSTP Per Port Config
LABEL
DESCRIPTION
Edge
Select On when the port is connected to an end node (a computer
network card for example).
Select Off when the port is connected to a bridge node.
P2P
Select On when the port is connected to one bridge as a Point-toPoint link type.
Select Off when the port is connected to multiple bridges as a
Shared Medium link type.
Select Auto to have the MES-2110 automatically determine the
link type.
96
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
Port
This indicates the port index number.
Type
This indicates the cable type connected to the port.
Priority (1~255)
This indicates the port priority.
Cost (1~65535)
This indicates the path cost for the port.
Edge
This indicates whether the port is connected to an end node (On)
or a bridge node (Off).
P2P
This indicates whether the port is connected to one bridge (On),
multiple bridges (Off), or if the connection type is determined
automatically (Auto).
Port Status
This indicates whether the port is Forwarding or Blocking frame
transmission.
Port Role
This indicates the port behavior as a Disabled, Alternate,
Backup, Root, Designated or NonStp port.
MES-2110 Users Guide
CHAPTER
12
VLAN
12.1 Overview
This chapter shows you how to configure 802.1Q tagged and port-based VLANs. A
VLAN (Virtual Local Area Network) is a network that is not limited by the physical
location of a device (such as a switch).
12.2 Introduction to IEEE 802.1Q Tagged VLANs
A tagged VLAN uses an explicit tag (VLAN ID) in the MAC header to identify the
VLAN membership of a frame across bridges - they are not confined to the switch
on which they were created. The VLANs can be created statically by hand or
dynamically through GVRP. The VLAN ID associates a frame with a specific VLAN
and provides the information that switches need to process the frame across the
network. A tagged frame is four bytes longer than an untagged frame and
contains two bytes of TPID (Tag Protocol Identifier, residing within the type/length
field of the Ethernet frame) and two bytes of TCI (Tag Control Information, starts
after the source address field of the Ethernet frame).
The CFI (Canonical Format Indicator) is a single-bit flag, always set to zero for
Ethernet switches. If a frame received at an Ethernet port has a CFI set to 1, then
that frame should not be forwarded as it is to an untagged port. The remaining
twelve bits define the VLAN ID, giving a possible maximum number of 4,096
VLANs. Note that user priority and VLAN ID are independent of each other. A
frame with VID (VLAN Identifier) of null (0) is called a priority frame, meaning that
only the priority level is significant and the default VID of the ingress port is given
as the VID of the frame. Of the 4096 possible VIDs, a VID of 0 is used to identify
priority frames and value 4095 (FFF) is reserved, so the maximum possible VLAN
configurations are 4,094.
TPID
User Priority
2 Bytes 3 Bits
MES-2110 Users Guide
CFI
VLAN ID
1 Bit
12 bits
97
Chapter 12 VLAN
12.2.1 Forwarding Tagged and Untagged Frames
Each port on the MES-2110 is capable of passing tagged or untagged frames. To
forward a frame from an 802.1Q VLAN-aware switch to an 802.1Q VLAN-unaware
switch, the MES-2110 first decides where to forward the frame and then strips off
the VLAN tag. To forward a frame from an 802.1Q VLAN-unaware switch to an
802.1Q VLAN-aware switch, the MES-2110 first decides where to forward the
frame, and then inserts a VLAN tag reflecting the ingress port's default VID. The
default PVID is VLAN 1 for all ports, but this can be changed.
A broadcast frame (or a multicast frame for a multicast group that is known by the
system) is duplicated only on ports that are members of the VID (except the
ingress port itself), thus confining the broadcast to a specific domain.
Please refer to the following table for common IEEE 802.1Q VLAN terminology.
Table 28 IEEE 802.1Q VLAN Terminology
VLAN
PARAMETER
TERM
DESCRIPTION
VLAN Type
Permanent VLAN
This is a static VLAN created manually.
Dynamic VLAN
This is a VLAN configured by a GVRP registration/
deregistration process.
Registration Fixed
Fixed registration ports are permanent VLAN
members.
Registration
Forbidden
Ports with registration forbidden are forbidden to
join the specified VLAN.
Normal
Registration
Ports dynamically join a VLAN using GVRP.
Tagged
Ports belonging to the specified VLAN tag all
outgoing frames transmitted.
Untagged
Ports belonging to the specified VLAN don't tag all
outgoing frames transmitted.
Port VID
This is the VLAN ID assigned to untagged frames
that this port received.
Acceptable Frame
Type
You may choose to accept both tagged and
untagged incoming frames, just tagged incoming
frames or just untagged incoming frames on a
port.
Ingress filtering
If set, the MES-2110 discards incoming frames
for VLANs that do not have this port as a
member.
VLAN
Administrative
Control
VLAN Tag Control
VLAN Port
98
MES-2110 Users Guide
Chapter 12 VLAN
12.3 The VLAN Type Screen
Use this screen to select the VLAN type. Click Configuration > VLAN Menu >
VLAN Type to open the following screen.
Figure 39 Configuration > VLAN Menu > VLAN Type
The following table describes the labels in this screen.
Table 29 Configuration > VLAN Menu > VLAN Type
LABEL
DESCRIPTION
VLAN Type
Use this to set the MES-2110 to Port-Based or TagBased(802.1q) VLAN mode.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
12.4 The Port-Based VLAN Screen
Port-based VLANs are VLANs where the frame forwarding decision is based on the
destination MAC address and its associated port.
Port-based VLANs require allowed outgoing ports to be defined for each port.
Therefore, if you wish to allow two subscriber ports to talk to each other, for
example, between conference rooms in a hotel, you must define the egress (an
egress port is an outgoing port, that is, a port through which a data frame leaves)
for both ports.
Port-based VLANs are specific only to the MES-2110 on which they were created.
MES-2110 Users Guide
99
Chapter 12 VLAN
This screen is available only when you select Port-Based in the VLAN Type
screen. Click Configuration > VLAN Menu > Port-Based to open the following
screen.
Figure 40 Configuration > VLAN Menu > Port-Based
The following table describes the labels in this screen.
Table 30 Configuration > VLAN Menu > Port-Based
LABEL
DESCRIPTION
Port-Based VLAN Configuration
Port Number
Use this to select the port you are configuring.
Port1-10
Select the subscriber ports that can talk to each other.
Switch Management
Use this to enable or disable switch management via the web
configurator, Telnet or SNMP manager. Select the port through
which you can manage the MES-2110. If you disable this feature,
then you cannot access the web configurator from a computer
connected to this port.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
Port-Based VLAN Status
100
Port Number
This is the port number.
Port1-10
This shows the subscriber ports that can talk to each other.
Switch Management
This shows whether switch management is enabled or disabled.
MES-2110 Users Guide
Chapter 12 VLAN
12.5 The Tag-Based VLAN Screens
Use the Tag-Based VLAN screens to configure VLAN settings.
12.5.1 VLAN Stacking
A service provider can use VLAN stacking to allow it to distinguish multiple
customers VLANs, even those with the same (customer-assigned) VLAN ID, within
its network.
Use VLAN stacking to add an outer VLAN tag to the inner IEEE 802.1Q tagged
frames that enter the network. By tagging the tagged frames (double-tagged
frames), the service provider can manage up to 4,094 VLAN groups with each
group containing up to 4,094 customer VLANs. This allows a service provider to
provide different service, based on specific VLANs, for many different customers.
A service providers customers may require a range of VLANs to handle multiple
applications. A service providers customers can assign their own inner VLAN tags
on ports for these applications. The service provider can assign an outer VLAN tag
for each customer. Therefore, there is no VLAN tag overlap among customers, so
traffic from different customers is kept separate.
12.5.2 VLAN Stacking Example
In the following example figure, both A and B are Service Providers Network
(SPN) customers with VPN tunnels between their head offices and branch offices
respectively. Both have an identical VLAN tag for their VLAN group. The service
provider can separate these two VLANs within its network by adding tag 37 to
MES-2110 Users Guide
101
Chapter 12 VLAN
distinguish customer A and tag 48 to distinguish customer B at edge device 1 and
then stripping those tags at edge device 2 as the data frames leave the network.
Figure 41 VLAN Stacking Example
12.5.3 VLAN Stacking Port Roles
Each port can have three VLAN stacking roles, Normal, Access Port and
Tunnel (the latter is for Gigabit ports only).
Note: Some devices do not support all roles.
Select Normal for regular (non-VLAN stacking) IEEE 802.1Q frame switching.
Select Access Port for ingress ports on the service provider's edge devices (1
and 2 in the VLAN stacking example figure). The incoming frame is treated as
"untagged", so a second VLAN tag (outer VLAN tag) can be added.
Note: Static VLAN Tx Tagging MUST be disabled on a port where you choose
Normal or Access Port.
Select Tunnel Port (available for Gigabit ports only) for egress ports at the
edge of the service provider's network. All VLANs belonging to a customer can
be aggregated into a single service provider's VLAN (using the outer VLAN tag
defined by SP VID).
Note: Static VLAN Tx Tagging MUST be enabled on a port where you choose Tunnel
Port.
102
MES-2110 Users Guide
Chapter 12 VLAN
12.5.4 VLAN Tag Format
A VLAN tag (service provider VLAN stacking or customer IEEE 802.1Q) consists of
the following three fields.
Table 31 VLAN Tag Format
Type
Priority
VID
Type is a standard Ethernet type code identifying the frame and indicates that
whether the frame carries IEEE 802.1Q tag information. SP TPID (Service
Provider Tag Protocol Identifier) is the service provider VLAN stacking tag type.
Many vendors use 0x8100 or 0x9100.
TPID (Tag Protocol Identifier) is the customer IEEE 802.1Q tag.
If the VLAN stacking port role is Access, then the MES-2110 adds the SP TPID
tag to all incoming frames on the service provider's edge devices (1 and 2 in the
VLAN stacking example figure).
If the VLAN stacking port role is Tunnel, then the MES-2110 only adds the SP
TPID tag to all incoming frames on the service provider's edge devices (1 and 2
in the VLAN stacking example figure) that have an SP TPID different to the one
configured on the MES-2110. (If an incoming frames SP TPID is the same as
the one configured on the MES-2110, then the MES-2110 will not add the tag.)
Priority refers to the IEEE 802.1p standard that allows the service provider to
prioritize traffic based on the class of service (CoS) the customer has paid for.
On the MES-2110, configure priority level of inner IEEE 802.1Q tag in the
Configuration > QoS Menu > 802.1p Priority screen.
"0" is the lowest priority level and "7" is the highest.
VID is the VLAN ID. SP VID is the VID for the second (service providers) VLAN
tag.
MES-2110 Users Guide
103
Chapter 12 VLAN
12.5.5 Frame Format
The frame format for an untagged Ethernet frame, a single-tagged 802.1Q frame
(customer) and a double-tagged 802.1Q frame (service provider) is shown next.
Configure the fields as highlighted in the MES-2110 VLAN Stacking screen.
Table 32 Single and Double Tagged 802.11Q Frame Format
DA
DA
SA SPTPID Priority
DA
SA
Len/
Etype
Data
FCS
Untagged
Ethernet
frame
SA
TPID
Priority
VID
Len/
Etype
Data
FCS
IEEE 802.1Q
customer
tagged
frame
VID
TPID
Priority
VID
Len/
Etype
Data
FCS
Doubletagged
frame
Table 33 802.1Q Frame
104
DA
Destination Address
Priority
802.1p Priority
SA
Source Address
Len/
Etype
Length and type of Ethernet
frame
(SP)TPID
(Service Provider) Tag Protocol
IDentifier
Data
Frame data
VID
VLAN ID
FCS
Frame Check Sequence
MES-2110 Users Guide
Chapter 12 VLAN
12.5.6 The VLAN Stacking Configuration Screen
Use this screen to enable VLAN stacking on the MES-2110. Click Configuration >
VLAN Menu > Tag-Based > VLAN Stacking to open the following screen.
Figure 42 Configuration > VLAN Menu > Tag-Based > VLAN Stacking
The following table describes the labels in this screen.
Table 34 Configuration > VLAN Menu > Tag-Based > VLAN Stacking
LABEL
DESCRIPTION
VLAN Stacking
Active
Select this to enable VLAN stacking on the MES-2110.
SP TPID
SP TPID is a standard Ethernet type code identifying the frame
and indicates whether the frame carries IEEE 802.1Q tag
information. Choose 0x8100 or 0x9100 from the drop-down list
box or select Others and then enter a four-digit hexadecimal
number from 0x0000 to 0xFFFF. 0x denotes a hexadecimal
number. It does not have to be typed in the Others text field.
Port
The port number identifies the port you are configuring.
Role
Select Access to have the MES-2110 add the SP TPID tag to all
incoming frames received on this port. Select Access Port for
ingress ports at the edge of the service provider's network.
Select Tunnel (available for Gigabit ports only) for egress ports
at the edge of the service provider's network.
In order to support VLAN stacking on a port, the port must be
able to allow frames of 1526 Bytes (1522 Bytes + 4 Bytes for the
second tag) to pass through it.
MES-2110 Users Guide
105
Chapter 12 VLAN
Table 34 Configuration > VLAN Menu > Tag-Based > VLAN Stacking
LABEL
DESCRIPTION
SPVID
SPVID is the service providers VLAN ID (the outer VLAN tag).
Enter the service provider ID (from 1 to 4094) for frames received
on this port.
Priority
On the MES-2110, configure priority level of inner IEEE 802.1Q
tag in the Configuration > QoS Menu > 802.1p Priority
screen.
"0" is the lowest priority level and "7" is the highest.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
VLAN Stacking Status
106
Port1-10
This is the port number.
Active
This shows whether VLAN stacking is enabled or disabled on the
MES-2110.
SP TPID
This is the service provider VLAN tag.
Role
This shows how the port process transmitted frames.
SPVID
This is the service provider ID for frames received on this port.
Priority
This shows the priority level of frames transmitted through the
port.
MES-2110 Users Guide
Chapter 12 VLAN
12.5.7 The Tag-Based Port Information Screen
Use this screen to configure how the MES-2110 handles incoming traffic passing
through the port.
Click Configuration > VLAN Menu > Tag-Based > Port Info. to open the
following screen.
Figure 43 Configuration > VLAN Menu > Tag-Based > Port Info.
The following table describes the labels in this screen.
Table 35 Configuration > VLAN Menu > Tag-Based > Port Info.
LABEL
DESCRIPTION
Port
This is the port index number.
PVID
Enter a number between 1 and 4094 as the port VLAN ID.
Ingress Filter
Use this to determine the action about incoming traffic passing
through the port.
Isolation
NonMember: Forward, Untagged: Forward: Forward
frames that do not belong to any VLAN group and forward
untagged VLAN frames.
NonMember: Drop, Untagged: Forward: Drop frames that
do not belong to any VLAN group and forward untagged VLAN
frames.
NonMember: Drop, Untagged: Drop: Drop frames that do
not belong to any VLAN group and drop untagged VLAN
frames.
Use this to enable or disable port isolation.
Port isolation allows each port to communicate only with the
management port but not communicate with each other. This
option is the most limiting but also the most secure.
MES-2110 Users Guide
107
Chapter 12 VLAN
Table 35 Configuration > VLAN Menu > Tag-Based > Port Info.
LABEL
DESCRIPTION
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
12.5.8 The Tag-Based Port Configuration Screen
Use this screen to configure the VLAN group settings for each port on the MES-2110.
Click Configuration > VLAN Menu > Tag-Based > Tag-Based info. to open
the following screen.
Figure 44 Configuration > VLAN Menu > Tag-Based > Tag-Based info.
The following table describes the labels in this screen.
Table 36 Configuration > VLAN Menu > Tag-Based > Tag-Based info.
LABEL
DESCRIPTION
VLAN ID
Select whether you want to Add or Modify a VLAN ID.
Enter the VLAN ID from 1-4094 that you want to configure.
Priority
108
This is the priority you want to assign to the tag-based VLAN.
MES-2110 Users Guide
Chapter 12 VLAN
Table 36 Configuration > VLAN Menu > Tag-Based > Tag-Based info.
LABEL
DESCRIPTION
Pri-Override
Select Enable to ignore the priority level assigned to the
transmitted frames. Otherwise, select Disable.
Port
This shows ports 1 to 10.
Member
This shows the VLAN group setting for the port, whether it is a
Member, Untagging, Tagging or Non-member.
Undo
Click this to reset the values in this screen to their last-saved
values.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
Tag VLAN Status (M:member U:untag T:tag)
Add VLAN Configuration
VLAN ID
Enter a VLAN ID number from 1 to 4094.
Priority
This is the priority you want to assign to the Tag-based VLAN.
Pri-Override
Select Enable to ignore the priority level assigned to the
transmitted frames. Otherwise, select Disable.
Port 1-10
A Member port is a permanent member of this VLAN group.
An Untagging port strips off the 802.1Q tag from incoming and
outgoing frames. Use this to send untag frames to devices that do
no support the 802.1Q feature.
A Tagging port tags incoming and outgoing frames with this
VLAN group information.
A Non-member port does not participate in the VLAN group.
Page Up
Click this to view the next page.
Page Down
Click this to view the previous page.
Refresh
Click this to refresh the screen.
Page... Set
Enter a page number and click Set to go to that page.
12.5.9 The Management VLAN Screen
Use this to configure the management VLAN. A port must belong to the
management VLAN if you want to access the MES-2110s web configurator via that
MES-2110 Users Guide
109
Chapter 12 VLAN
port. Click Configuration > VLAN Menu > Tag-Based > Management VLAN
to open the following screen.
Figure 45 Configuration > VLAN Menu > Tag-Based > Management VLAN
The following table describes the labels in this screen.
Table 37 Configuration > VLAN Menu > Tag-Based > Management VLAN
110
LABEL
DESCRIPTION
Management VLAN
This is the current management VLAN.
VLAN ID
Enter an ID number from 1 to 4094. 1 is the default value. If you
change this, you will be disconnected from the web configurator
unless your current access belongs to the new VLAN.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
MES-2110 Users Guide
CHAPTER
13
Bandwidth Control
13.1 Overview
Bandwidth control means defining a maximum allowable bandwidth for incoming
and/or out-going traffic flows on a port.
13.2 Bandwidth Control Setup
Click Configuration > Bandwidth Control in the navigation panel to bring up
the screen as shown next.
Figure 46 Configuration > Bandwidth Control
MES-2110 Users Guide
111
Chapter 13 Bandwidth Control
The following table describes the related labels in this screen.
Table 38 Configuration > Bandwidth Control
LABEL
DESCRIPTION
Bandwidth Control Configuration
Port Number
Use this to select a port number.
Mode
This shows the Ingress (incoming) or Egress (outgoing) mode.
Rate Level
Select a rate range from the list. Options are: 64K~960K (64+), 1M~100M
(1M+), 110M~1000M (10M+).
Rate Limit
Specify the maximum bandwidth allowed for the traffic flow on a port. The
unit changes depending on how you configure in the Rate Level field. The
value you enter in this field must be within the rate level range.
Active
Use this to enable or disable bandwidth control.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory.
The MES-2110 loses these changes if it is turned off or loses power, so use
the Save Settings link in the navigation panel to save your changes to the
non-volatile memory when you are done configuring.
Bandwidth Control Status
Port
This is the port number.
Ingress Limit This is the ingress rate limit on the port.
112
Active
This shows whether bandwidth control for ingress traffic is enabled or
disabled on the port.
Egress Limit
This is the egress rate limit on the port.
Active
This shows whether bandwidth control for egress traffic is enabled or
disabled on the port.
MES-2110 Users Guide
CHAPTER
14
Broadcast Storm Control
14.1 Overview
This chapter introduces and shows you how to configure the broadcast storm
control feature.
14.2 Broadcast Storm Control Setup
Broadcast storm control limits the number of broadcast, multicast and destination
lookup failure (DLF) frames the MES-2110 receives per second on the ports. When
the maximum number of allowable broadcast, multicast and/or DLF frames is
reached per second, the subsequent frames are discarded. Enable this feature to
reduce broadcast, multicast and/or DLF frames in your network. You can specify
limits for each frame type on each port.
Click Configuration > Storm Control in the navigation panel to display the
screen as shown next.
Figure 47 Configuration > Storm Control
MES-2110 Users Guide
113
Chapter 14 Broadcast Storm Control
The following table describes the labels in this screen.
Table 39 Configuration > Storm Control
LABEL
DESCRIPTION
Storm Control Configuration
Port Number
Use this to select a port number.
Mode
Select the Broadcast, Multicast or DLF mode from the list.
Rate Level
Select a rate range from the list. Options are: 64K~960K (64+),
1M~100M (1M+), 110M~1000M (10M+).
Rate Limit
Specify specify how many frames the port receives per second. The unit
changes depending on how you configure in the Rate Level field. The
value you enter in this field must be within the rate level range.
Active
Use this to enable or disable storm control.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory.
The MES-2110 loses these changes if it is turned off or loses power, so
use the Save Settings link in the navigation panel to save your changes
to the non-volatile memory when you are done configuring.
Storm Control Status
114
Port
This is the port number.
Broadcast
Limit
This is the broadcast frame limit on the port.
Active
This shows whether broadcast control is enabled or disabled on the port.
Multicast Limit
This is the multicast frame limit on the port.
Active
This shows whether multicast control is enabled or disabled on the port.
DLF Limit
This is the Destination Lookup Failure (DLF) frame limit on the port.
Active
This shows whether DLF control is enabled or disabled on the port.
MES-2110 Users Guide
CHAPTER
15
Port Mirroring
15.1 Overview
This chapter discusses port mirroring setup screens.
15.2 Port Mirroring Setup
Port mirroring allows you to copy a traffic flow to a monitor port (the port you copy
the traffic to) in order that you can examine the traffic from the monitor port
without interference.
Click Configuration > Port Mirroring in the navigation panel to display the
following screen. Use this screen to select a monitor port and specify the traffic
flow to be copied to the monitor port.
Figure 48 Configuration > Port Mirroring
MES-2110 Users Guide
115
Chapter 15 Port Mirroring
The following table describes the labels in this screen.
Table 40 Configuration > Port Mirroring
116
LABEL
DESCRIPTION
Mirroring
Mode
Use this to enable or disable the port mirroring feature. The active port
mirroring feature monitors both incoming and outgoing traffic.
Monitoring
Port
The monitoring port is the port you copy the traffic to in order to examine it
in more detail without interfering with the traffic flow on the original port(s).
Select the monitor port number from the list.
Monitored
Port
Select the port(s) to mirror the traffic on a port.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory. The
MES-2110 loses these changes if it is turned off or loses power, so use the
Save Settings link in the navigation panel to save your changes to the nonvolatile memory when you are done configuring.
MES-2110 Users Guide
CHAPTER
16
Link Aggregation
16.1 Overview
Link aggregation (trunking) is the grouping of physical ports into one logical
higher-capacity link. You may want to trunk ports if for example, it is cheaper to
use multiple lower-speed links than to under-utilize a high-speed, but more costly,
single-port link.
However, the more ports you aggregate then the fewer available ports you have. A
trunk group is one logical link containing multiple ports.
The beginning port of each trunk group must be physically connected to form a
trunk group.
The MES-2110 supports both static and dynamic link aggregation.
Note: In a properly planned network, it is recommended to implement static link
aggregation only. This ensures increased network stability and control over the
trunk groups on your MES-2110.
See Section 16.3 on page 118 for a static port trunking example.
16.2 Dynamic Link Aggregation
The MES-2110 adheres to the IEEE 802.3ad standard for static and dynamic
(LACP) port trunking.
The MES-2110 supports the link aggregation IEEE802.3ad standard. This standard
describes the Link Aggregation Control Protocol (LACP), which is a protocol that
dynamically creates and manages trunk groups.
When you enable LACP link aggregation on a port, the port can automatically
negotiate with the ports at the remote end of a link to establish trunk groups.
LACP also allows port redundancy, that is, if an operational port fails, then one of
the standby ports become operational without user intervention. Please note
that:
MES-2110 Users Guide
117
Chapter 16 Link Aggregation
You must connect all ports point-to-point to the same Ethernet switch and
configure the ports for LACP trunking.
LACP only works on full-duplex links.
All ports in the same trunk group must have the same media type, speed,
duplex mode and flow control settings.
Configure trunk groups or LACP before you connect the Ethernet switch to avoid
causing network topology loops.
16.2.1 Link Aggregation ID
LACP aggregation ID consists of the following information2:
Table 41 Link Aggregation ID: Local Switch
SYSTEM
PRIORITY
MAC ADDRESS
KEY
PORT
PRIORITY
PORT
NUMBER
0000
00-00-00-00-00-00
0000
00
0000
Table 42 Link Aggregation ID: Peer Switch
SYSTEM
PRIORITY
MAC ADDRESS
KEY
PORT
PRIORITY
PORT NUMBER
0000
00-00-00-00-00-00
0000
00
0000
16.3 Static Trunking Example
This example shows you how to create a static port trunk group for ports 2-5.
1
Make your physical connections - make sure that the ports that you want to
belong to the trunk group are connected to the same destination. The following
figure shows ports 2-5 on switch A connected to switch B.
Figure 49 Trunking Example - Physical Connections
B
A
2.
118
Port Priority and Port Number are 0 as it is the aggregator ID for the trunk group, not the individual port.
MES-2110 Users Guide
Chapter 16 Link Aggregation
Configure static trunking-Click Configuration > Trunk Config > Aggregator
Setting. In this screen select the ports that should belong to trunk group 1 as
shown in the figure below. Do not select the LACP option. Click Apply when you
are done.
Figure 50 Trunking Example - Configuration Screen
Your trunk group 1 configuration is now complete; you do not need to go to any
additional screens.
16.4 Link Aggregation Setting
Click Configuration > Trunk Config > Aggregator Setting to display the
screen shown next. See Section 16.1 on page 117 for more information on link
aggregation.
Figure 51 Configuration > Trunk Config > Aggregator Setting
MES-2110 Users Guide
119
Chapter 16 Link Aggregation
The following table describes the labels in this screen.
Table 43 Configuration > Trunk Config > Aggregator Setting
LABEL
DESCRIPTION
Group
This is the trunk group index number.
The MES-2110 supports up to four trunk groups for 100Mbps ports and up
to two trunk groups for Gigabit ports. 100Mbps ports and Gigabit ports
cannot be in the same group.
Members
Select the port(s) that belong to a trunk group.
For Groups 1 to 4, you can select up to four port members for each group.
For Group 5, you can select the two Gigabit ports as the members.
LACP
Use this to enable or disable LACP port trunking.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory. The
MES-2110 loses these changes if it is turned off or loses power, so use the
Save Settings link in the navigation panel to save your changes to the
non-volatile memory when you are done configuring.
16.5 Link Aggregation Control Protocol
Click Configuration > Trunk Config > LACP Configuration to display the
screen shown next. See Section 16.2 on page 117 for more information on
dynamic link aggregation.
Figure 52 Configuration > Trunk Config > LACP Configuration
The following table describes the labels in this screen.
Table 44 Configuration > Trunk Config > LACP Configuration
LABEL
DESCRIPTION
Port State
Activity
Select the port to enable Link Aggregation Control Protocol (LACP).
Hash-mode
Use this to specify the outgoing traffic distribution type.
Select Lookup to distribute frames based on the destination MAC address.
Select Xor to distribute frames based on the last 3 bits of the source MAC
address and the trunk mask load balancing table.
120
MES-2110 Users Guide
Chapter 16 Link Aggregation
Table 44 Configuration > Trunk Config > LACP Configuration (continued)
LABEL
DESCRIPTION
System
Priority
LACP system priority is a number between 1 and 65535. The switch with
the lowest system priority (and lowest port number if system priority is the
same) becomes the LACP server. The LACP server controls the
operation of LACP setup. Enter a number to set the priority of an active port
using Link Aggregation Control Protocol (LACP). The smaller the number,
the higher the priority level.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory. The
MES-2110 loses these changes if it is turned off or loses power, so use the
Save Settings link in the navigation panel to save your changes to the
non-volatile memory when you are done configuring.
16.6 LACP Link Status
Click Configuration > Trunk Config > LACP Link Status in the navigation
panel to open the following screen.
Figure 53 Configuration > Trunk Config > LACP Link Status
The following table describes the labels in this screen.
Table 45 Configuration > Trunk Config > LACP Link Status
LABEL
DESCRIPTION
Actor
This is the local MES-2110.
MAC
This is the local MES-2110s MAC address.
Priority
This is the local MES-2110s priority level.
Port ID
This shows the port number belonging to the trunk group.
Key
This is the local MES-2110s key value.
Priority
This is the port priority level.
Partner
This is the peer MES-2110.
MAC
This is the peer MES-2110s MAC address.
Priority
This is the peer MES-2110s priority level.
Port ID
This shows the port number belonging to the trunk group.
MES-2110 Users Guide
121
Chapter 16 Link Aggregation
Table 45 Configuration > Trunk Config > LACP Link Status (continued)
122
LABEL
DESCRIPTION
Key
This is the peer MES-2110s key value.
Priority
This is the port priority level.
MES-2110 Users Guide
CHAPTER
17
IGMP
17.1 Overview
Traditionally, IP frames are transmitted in one of either two ways - Unicast (1
sender to 1 recipient) or Broadcast (1 sender to everybody on the network).
Multicast delivers IP frames to just a group of hosts on the network.
IGMP (Internet Group Management Protocol) is a network-layer protocol used to
establish membership in a multicast group - it is not used to carry user data. Refer
to RFC 1112, RFC 2236 and RFC 3376 for information on IGMP versions 1, 2 and 3
respectively.
17.1.1 IP Multicast Addresses
In IPv4, a multicast address allows a device to send frames to a specific group of
hosts (multicast group) in a different subnetwork. A multicast IP address
represents a traffic receiving group, not individual receiving devices. IP addresses
in the Class D range (224.0.0.0 to 239.255.255.255) are used for IP multicasting.
Certain IP multicast numbers are reserved by IANA for special purposes (see the
IANA web site for more information).
17.1.2 IGMP Snooping
A MES-2110 can passively snoop on IGMP frames transferred between IP
multicast routers/switches and IP multicast hosts to learn the IP multicast group
membership. It checks IGMP frames passing through it, picks out the group
registration information, and configures multicasting accordingly. IGMP snooping
allows the MES-2110 to learn multicast groups without you having to manually
configure them.
The MES-2110 forwards multicast traffic destined for multicast groups (that it has
learned from IGMP snooping or that you have manually configured) to ports that
are members of that group. IGMP snooping generates no additional network
traffic, allowing you to significantly reduce multicast traffic passing through your
MES-2110.
MES-2110 Users Guide
123
Chapter 17 IGMP
17.1.3 IGMP Snooping and VLANs
The MES-2110 can perform IGMP snooping on up to 16 VLANs. You can configure
the MES-2110 to automatically learn multicast group membership of any VLANs.
The MES-2110 then performs IGMP snooping on the first 16 VLANs that send IGMP
frames. This is referred to as auto mode. Alternatively, you can specify the VLANs
that IGMP snooping should be performed on. This is referred to as fixed mode. In
fixed mode the MES-2110 does not learn multicast group membership of any
VLANs other than those explicitly added as an IGMP snooping VLAN.
17.2 IGMP Configuration
Use this screen to configure the MES-2110s IGMP settings.
Click Configuration > IGMP Menu > IGMP Config to open the following screen.
Figure 54 Configuration > IGMP Menu > IGMP Config
124
MES-2110 Users Guide
Chapter 17 IGMP
The following table describes the labels in this screen.
Table 46 Configuration > IGMP Menu > IGMP Config
LABEL
DESCRIPTION
IGMP Snooping
Use this to enable or disable IGMP snooping.
When IGMP is enabled, the MES-2110 forwards group multicast
traffic only to ports that are members of that group.
IGMP VLAN Mode
Select Auto to have the MES-2110 learn multicast group
membership information of any VLANs automatically.
Select Fixed to have the MES-2110 only learn multicast group
membership information of the VLAN(s) that you specify below.
IGMP Query Mode
Specifies whether or not the port is an IGMP query port. The MES2110 forwards IGMP join or leave frames to an IGMP query port,
treating the port as being connected to an IGMP multicast router
(or server). You must enable IGMP snooping as well.
Select Auto to have the MES-2110 use the port as an IGMP query
port if the port received IGMP query frames recently. An auto port
doesnt forward any multicast group member information to its
uplink router if the switch didnt receive any IGMP query frames
from the router within a period.
Select Disable to turn this feature off for this port.
IGMP VLAN
Enter the ID of the static VLAN(s) that the MES-2110 includes in
its learning process of multicast group membership (of the ports).
Enter a VLAN ID between 1 and 4094.
IGMP VLAN Query
Mode
Click this to display the IGMP VLAN Query Mode screen.
Port 1-10
This shows the port numbers that you can configure individually
using the fields described below.
The Switch can forward multicast frames to IGMP static ports with
or without the learning process of multicast group membership.
Immediate Leave
Use this to enable or disable this feature.
When this is enabled on this port and the switch receives an IGMP
version 2 leave message for this port, this port is immediately
removed from the multicast group.
When this is disabled on this port and the switch receives an IGMP
version 2 leave message for this port, the Switch first uses this
port to send a query packet to ask its multicast group if it still has
active client requests. After one second and the Switch has not
receive a reply packet asking for the port's IGMP report, it
removes the port from the multicast group.
Static Query
Select Enable to stop the MES-2110 from using the port as an
IGMP query port. The MES-2110 will not keep any record of an
IGMP router being connected to this port.
Select Disable to have the MES-2110 use the port as an IGMP
query port if the port receives IGMP query frames.
Undo
MES-2110 Users Guide
Click this to restore your last saved settings.
125
Chapter 17 IGMP
Table 46 Configuration > IGMP Menu > IGMP Config
LABEL
DESCRIPTION
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
IGMP Snooping
This indicates whether IGMP snooping is enabled or disabled for
this port.
IGMP VLAN Mode
This indicates whether the IGMP VLAN Mode is set to Auto or
Fixed for this port.
IGMP Query Mode
This indicates whether the IGMP Query Mode is set to Auto or
Disable for this port.
IGMP VLAN
This indicates the static VLAN ID the MES-2110 uses to learn
multicast group membership.
Immediate Leave
This indicates whether Immediate Leave is enabled or disabled
for this port.
Static Query
This indicates whether Static Query is enabled or disabled for
this port.
17.2.1 IGMP VLAN Query Mode
Click Configuration > IGMP Menu > IGMP Config then click the IGMP VLAN
Query Mode link to open the following screen.
Figure 55 Configuration > IGMP Menu > IGMP VLAN Query Mode
The following table describes the labels in this screen.
Table 47 Configuration > IGMP Menu > IGMP VLAN Query Mode
126
LABEL
DESCRIPTION
IGMP VLAN
Select an IGMP VLAN (previously configured in Section 17.2 on
page 124) from the list.
Query Mode
Select either Auto or Disable as the Query Mode for the specified
IGMP VLAN.
Undo
Click this to restore your last saved settings.
MES-2110 Users Guide
Chapter 17 IGMP
Table 47 Configuration > IGMP Menu > IGMP VLAN Query Mode (continued)
LABEL
DESCRIPTION
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory when you
are done configuring.
IGMP VLAN
This column displays the configured VLANs.
Query Mode
This column displays the whether the VLANs query mode is Auto
or Disable.
17.3 IGMP Status
Click Configuration > IGMP Menu > IGMP Group Status to display the screen
as shown. This screen shows the multicast group information. See Section 17.1 on
page 123 for more information on multicasting.
Figure 56 Configuration > IGMP Menu > IGMP Group Status
The following table describes the labels in this screen.
Table 48 Configuration > IGMP Menu > IGMP Group Status
LABEL
DESCRIPTION
No
This is the index number of the entry.
Multicast Group
This field displays IP multicast group addresses.
VLAN ID
This field displays the multicast VLAN ID.
Port
This field displays the port number that belongs to the multicast group.
17.4 MVR Overview
Multicast VLAN Registration (MVR) is designed for applications (such as Media-onDemand (MoD)) that use multicast traffic across an Ethernet ring-based service
provider network.
MVR allows one single multicast VLAN to be shared among different subscriber
VLANs on the network. While isolated in different subscriber VLANs, connected
devices can subscribe to and unsubscribe from the multicast stream in the
multicast VLAN. This improves bandwidth utilization with reduced multicast traffic
in the subscriber VLANs and simplifies multicast group management.
MES-2110 Users Guide
127
Chapter 17 IGMP
MVR only responds to IGMP join and leave control messages from multicast
groups that are configured under MVR. Join and leave reports from other multicast
groups are managed by IGMP snooping.
The following figure shows a network example. The subscriber VLAN (1, 2 and 3)
information is hidden from the streaming media server, S. In addition, the
multicast VLAN information is only visible to the MES-2110 and S.
Figure 57 MVR Network Example
17.4.1 Types of MVR Ports
In MVR, a source port is a port on the MES-2110 that can send and receive
multicast traffic in a multicast VLAN while a receiver port can only receive
multicast traffic. Once configured, the MES-2110 maintains a forwarding table that
matches the multicast stream to the associated multicast group.
17.4.2 MVR Modes
You can set your MES-2110 to operate in either dynamic or compatible mode.
In dynamic mode, the MES-2110 sends IGMP leave and join reports to the other
multicast devices (such as multicast routers or servers) in the multicast VLAN.
This allows the multicast devices to update the multicast forwarding table to
forward or not forward multicast traffic to the receiver ports.
In compatible mode, the MES-2110 does not send any IGMP reports. In this case,
you must manually configure the forwarding settings on the multicast devices in
the multicast VLAN.
17.4.3 How MVR Works
The following figure shows a multicast television example where a subscriber
device (such as a computer) in VLAN 1 receives multicast traffic from the
streaming media server, S, via the MES-2110. Multiple subscriber devices can
connect through a port configured as the receiver on the MES-2110.
When the subscriber selects a television channel, computer A sends an IGMP
report to the MES-2110 to join the appropriate multicast group. If the IGMP report
matches one of the configured MVR multicast group addresses on the MES-2110,
128
MES-2110 Users Guide
Chapter 17 IGMP
an entry is created in the forwarding table on the MES-2110. This maps the
subscriber VLAN to the list of forwarding destinations for the specified multicast
traffic.
When the subscriber changes the channel or turns off the computer, an IGMP
leave message is sent to the MES-2110 to leave the multicast group. The MES2110 sends a query to VLAN 1 on the receiver port (in this case, a DSL port on the
MES-2110). If there is another subscriber device connected to this port in the
same subscriber VLAN, the receiving port will still be on the list of forwarding
destination for the multicast traffic. Otherwise, the MES-2110 removes the
receiver port from the forwarding table.
Figure 58 MVR Multicast Television Example
17.5 General MVR Configuration
Use the MVR screen to create multicast VLANs and select the receiver port(s) and
a source port for each multicast VLAN. Click Configuration > IGMP Menu >
MVR link to display the screen as shown next.
Note: You can create up to three multicast VLANs and up to 256 multicast rules on the
MES-2110.
MES-2110 Users Guide
129
Chapter 17 IGMP
Note: Your MES-2110 automatically creates a static VLAN (with the same VID) when
you create a multicast VLAN in this screen.
Figure 59 Configuration > IGMP Menu > MVR
The following table describes the related labels in this screen.
Table 49 Configuration > IGMP Menu > MVR
LABEL
DESCRIPTION
MVR
Active
Select this check box to enable MVR to allow one single multicast VLAN
to be shared among different subscriber VLANs on the network.
Name
Enter a descriptive name (up to 32 printable ASCII characters) for
identification purposes.
Multicast VLAN
ID
Enter the VLAN ID (1 to 4094) of the multicast VLAN.
Query Mode
Choose Auto to have the MES-2110 select the querier automatically, or
Disable to turn this feature off.
Mode
Specify the MVR mode on the MES-2110. Choices are Dynamic and
Compatible.
Select Dynamic to send IGMP reports to all MVR source ports in the
multicast VLAN.
Select Compatible to set the MES-2110 not to send IGMP reports.
130
MES-2110 Users Guide
Chapter 17 IGMP
Table 49 Configuration > IGMP Menu > MVR (continued)
LABEL
DESCRIPTION
Port
This field displays the port number on the MES-2110.
Source Port
Select this option to set this port as the MVR source port that sends and
receives multicast traffic. All source ports must belong to a single
multicast VLAN.
Receiver Port
Select this option to set this port as a receiver port that only receives
multicast traffic.
None
Select this option to set the port not to participate in MVR. No MVR
multicast traffic is sent or received on this port.
Tagging
Select this checkbox if you want the port to tag the VLAN ID in all
outgoing frames transmitted.
All Port
Use this to select between Source Port, Receiver Port or None.
Tagging
Select this checkbox if you want the ports to tag the VLAN ID in all
outgoing frames transmitted.
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the MES-2110s run-time memory.
The MES-2110 loses these changes if it is turned off or loses power, so
use the Save Settings link in the navigation panel to save your changes
to the non-volatile memory when you are done configuring.
MVR Status
VLAN
This field displays the multicast VLAN ID.
Active
This field displays whether the multicast group is enabled or not.
Query Mode
This field displays whether the query mode is enabled or not.
Name
This field displays the descriptive name for this setting.
Mode
This field displays the MVR mode.
Source Port
This field displays the source port number(s).
Receiver Port
This field displays the receiver port number(s).
Tagging Port
This field displays which port tags outgoing frames with the VLAN ID.
Delete
To delete a multicast VLAN(s), select the rule(s) that you want to
remove in the Delete column, then click the Delete button.
Undo
Click this to clear the Delete check boxes.
17.6 MVR Group Configuration
All source ports and receiver ports belonging to a multicast group can receive
multicast data sent to this multicast group.
Configure MVR IP multicast group address(es) in the Group Configuration
screen. Click Group Configuration in the MVR screen.
MES-2110 Users Guide
131
Chapter 17 IGMP
Note: A port can belong to more than one multicast VLAN. However, IP multicast
group addresses in different multicast VLANs cannot overlap.
Figure 60 Configuration > IGMP Menu > MVR > Group Configuration
The following table describes the labels in this screen.
Table 50 Configuration > IGMP Menu > MVR > Group Configuration
LABEL
DESCRIPTION
Group Configuration
Multicast
VLAN ID
Select a multicast VLAN ID (that you configured in the MVR screen) from
the drop-down list box.
Group ID
Enter a group number for identification purposes.
Start
Address
Enter the starting IP multicast address of the multicast group in dotted
decimal notation.
Refer to Section 17.1.1 on page 123 for more information on IP multicast
addresses.
Quantity
Specify the number of IP addresses to include in the multicast group.
Undo
Click this to load your last saved settings.
Add
Click Add to save your changes to the MES-2110s run-time memory. The
MES-2110 loses these changes if it is turned off or loses power, so use the
Save link on the top navigation panel to save your changes to the nonvolatile memory when you are done configuring.
MVR Group Status
132
MVLAN
This field displays the multicast VLAN ID.
Group ID
This field displays the ID number that identifies the multicast group.
Address
This field displays the starting IP address of the multicast group.
Delet All
Select the check box and click the Delete button to remove all configured
rules.
Delete
Group
Select the check box in the Delete Group field and click Delete to remove
the selected entry(ies) from the table.
Undo
Select this to clear the checkbox(es) in the table.
MES-2110 Users Guide
Chapter 17 IGMP
17.6.1 MVR Configuration Example
The following figure shows a network example where ports 1, 2 and 3 on the MES2110 belong to VLAN 1. In addition, port 7 belongs to the multicast group with
VID 200 to receive multicast traffic (the News and Movie channels) from the
remote streaming media server, S. Computers A, B and C in VLAN are able to
receive the traffic.
Figure 61 MVR Configuration Example
MES-2110 Users Guide
133
Chapter 17 IGMP
To configure the MVR settings on the MES-2110, create a multicast group in the
MVR screen and set the receiver and source ports.
Figure 62 MVR Configuration Example
To set the MES-2110 to forward the multicast group traffic to the subscribers,
configure multicast group settings in the Group Configuration screen. The
134
MES-2110 Users Guide
Chapter 17 IGMP
following figure shows an example where two multicast groups (Group ID 1 for
News and Group ID 2 for Movie) are configured for the multicast VLAN 200.
Figure 63 MVR Group Configuration Example
Figure 64 MVR Group Configuration Example
MES-2110 Users Guide
135
Chapter 17 IGMP
136
MES-2110 Users Guide
CHAPTER
18
DHCP Relay Configuration
18.1 Overview
Configure DHCP relay on the MES-2110 if the DHCP clients and the DHCP server
are not in the same broadcast domain. During the initial IP address leasing, the
MES-2110 helps to relay network information (such as the IP address and subnet
mask) between a DHCP client and a DHCP server. Once the DHCP client obtains an
IP address and can connect to the network, network information renewal is done
between the DHCP client and the DHCP server without the help of the MES-2110.
The MES-2110 can be configured as a global DHCP relay. This means that the
MES-2110 forwards all DHCP requests from all domains to the same DHCP server.
You can also configure the MES-2110 to relay DHCP information based on the
VLAN membership of the DHCP clients.
18.1.1 DHCP Relay Agent Information
The MES-2110 can add information about the source of client DHCP requests that
it relays to a DHCP server by adding Relay Agent information. This helps provide
authentication about the source of the requests. The DHCP server can then
provide an IP address based on this information. Please refer to RFC 3046 for
more details.
The DHCP Relay Agent feature adds an additional parameter to the Option 82
field. The Option 82 field is in the DHCP headers of client DHCP request frames
that the MES-2110 relays to a DHCP server.
The following describes the DHCP relay information that the MES-2110 sends to
the DHCP server:
Table 51 Relay Agent Information
FIELD LABELS
DESCRIPTION
Slot ID
(1 byte) This value is always 0 for stand-alone non-card based
switches.
Port ID
(1 byte) This is the port that the DHCP client is connected to.
MES-2110 Users Guide
137
Chapter 18 DHCP Relay Configuration
Table 51 Relay Agent Information
FIELD LABELS
DESCRIPTION
VLAN ID
(2 bytes) This is the VLAN that the port belongs to.
Remote ID
(up to 64 bytes) This optional field is set on the DHCP Relay
Configuration (Section 19.2 on page 143) screen
18.2 DHCP Relay Configuration
This screen allows you to configure the DHCP Relay Agent, which sends messages
between DHCP clients and DHCP servers on different IP networks.
Click Configuration > DHCP Relay Configuration to open this screen.
Figure 65 Configuration > DHCP Relay Configuration
The following table describes the labels in this screen.
Table 52 Configuration > DHCP Relay Configuration
LABEL
DESCRIPTION
DHCP Relay Agent Configuration
138
Active
Select this check box to enable DHCP relay.
Remote DHCP Server
Enter the IP address of a DHCP server in dotted decimal notation.
Smart Relay Exclude
VLAN
Enter the VLAN ID to exclude from the DHCP relay function.
Option82
Select this to have the MES-2110 add information (slot number,
port number and VLAN ID) to client DHCP requests that it relays
to a DHCP server.
MES-2110 Users Guide
Chapter 18 DHCP Relay Configuration
Table 52 Configuration > DHCP Relay Configuration (continued)
LABEL
DESCRIPTION
Option82 Information
Enter a unique identifier (such as the MES-2110s MAC address)
for the DHCP relay agent. This must be globally unique. You can
enter up to 64 ASCII characters.
Undo
Click this to reset the values in this screen to their last-saved
values.
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save link on the top navigation panel to
save your changes to the non-volatile memory when you are
done configuring.
DHCP Relay Agent Status
Active
This indicates whether DHCP relay is enabled or disabled.
Remote DHCP server
This indicates the remote DHCP servers IP address.
Smart-Relay Exclude
VLAN
This indicates which VLAN IDs are excluded from the DHCP relay
function.
Option82
This indicates whether Option82 is enabled or disabled.
Option82 Information
This indicates the remote ID of the DHCP relay agent.
MES-2110 Users Guide
139
Chapter 18 DHCP Relay Configuration
140
MES-2110 Users Guide
CHAPTER
19
IP Source Guard
19.1 Overview
IP source guard uses a binding table to distinguish between authorized and
unauthorized DHCP and ARP frames in your network. A binding contains these key
attributes:
MAC address
VLAN ID
IP address
Port number
When the MES-2110 receives a DHCP or ARP frame, it looks up the appropriate
MAC address, VLAN ID, IP address, and port number in the binding table. If there
is a binding, the MES-2110 forwards the frame. If there is not a binding, the MES2110 discards the frame.
The MES-2110 builds the binding table by snooping DHCP frames (dynamic
bindings) and from information provided manually by administrators (static
bindings).
IP source guard consists of the following features:
Static bindings. Use this to create static bindings in the binding table.
DHCP snooping. Use this to filter unauthorized DHCP frames on the network and
to build the binding table dynamically.
ARP inspection. Use this to filter unauthorized ARP frames on the network.
If you want to use dynamic bindings to filter unauthorized ARP frames (typical
implementation), you have to enable DHCP snooping before you enable ARP
inspection.
MES-2110 Users Guide
141
Chapter 19 IP Source Guard
19.1.1 DHCP Snooping Overview
Use DHCP snooping to filter unauthorized DHCP frames on the network and to
build the binding table dynamically. This can prevent clients from getting IP
addresses from unauthorized DHCP servers.
19.1.1.1 Trusted vs. Untrusted Ports
Every port is either a trusted port or an untrusted port for DHCP snooping. This
setting is independent of the trusted/untrusted setting for ARP inspection. You can
also specify the maximum number for DHCP frames that each port (trusted or
untrusted) can receive each second.
Trusted ports are connected to DHCP servers or other switches. The MES-2110
discards DHCP frames from trusted ports only if the rate at which DHCP frames
arrive is too high. The MES-2110 learns dynamic bindings from trusted ports.
Note: If DHCP is enabled and there are no trusted ports, DHCP requests will not
succeed.
Untrusted ports are connected to subscribers. The MES-2110 discards DHCP
frames from untrusted ports in the following situations:
The frame is a DHCP server frame (for example, OFFER, ACK, or NACK).
The source MAC address and source IP address in the frame do not match any
of the current bindings.
The frame is a RELEASE or DECLINE frame, and the source MAC address and
source port do not match any of the current bindings.
The rate at which DHCP frames arrive is too high.
19.1.1.2 DHCP Snooping Static Binding Table
The MES-2110 stores the binding table in volatile memory. If the MES-2110
restarts, it loads static bindings from permanent memory but loses the dynamic
bindings, in which case the devices in the network have to send DHCP requests
again. As a result, it is recommended you configure the DHCP snooping database.
19.1.1.3 Configuring DHCP Snooping
Follow these steps to configure DHCP snooping on the MES-2110.
142
Enable DHCP snooping on the MES-2110.
Configure trusted and untrusted ports, and specify the maximum number of DHCP
frames that each port can receive per second.
MES-2110 Users Guide
Chapter 19 IP Source Guard
Configure static bindings.
19.2 DHCP Snooping Configuration
Use this screen to enable DHCP snooping on the MES-2110 and specify whether
ports are trusted or untrusted ports for DHCP snooping. To open this screen, click
Configuration > IP Source Guard > DHCP > DHCP Snooping Configuration.
Figure 66 Configuration > IP Source Guard > DHCP > DHCP Snooping
Configuration
MES-2110 Users Guide
143
Chapter 19 IP Source Guard
The following table describes the labels in this screen.
Table 53 Configuration > IP Source Guard > DHCP > DHCP Snooping
Configuration
LABEL
DESCRIPTION
DHCP Snooping Configuration
Action
Select Enable to have the MES-2110 use DHCP snooping . You
still have to enable DHCP snooping on specific VLAN and specify
trusted ports.
Select Disable if you do not want to use this feature.
Note: If DHCP is enabled and there are no trusted ports,
DHCP requests will not succeed.
DHCP snooping VLAN
Mode
Select All-VLAN to have the Switch forward DHCP frames of any
VLANs to DHCP servers automatically.
Select Fixed to have the Switch forward DHCP frames of a
specific VLAN to DHCP servers.
DHCP Snooping
Option
Select Enable to have the MES-2110 add DHCP relay agent
option 82 information to DHCP requests that the MES-2110
relays to a DHCP server for each VLAN. Otherwise, select
Disable.
Option82 Information
Enter a unique identifier (such as the MES-2110s MAC address)
for the DHCP relay agent. This must be globally unique. You can
enter up to 64 ASCII characters.
DHCP VLAN (Fixed)
Enter the ID of a static VLAN; the valid range is between 1 and
4094.
Port
This field displays the port number. If you configure the * port,
the settings are applied to all of the ports.
Trust
Use this to set trusted ports.
Trusted ports are connected to DHCP servers or other switches,
and the MES-2110 discards DHCP frames from trusted ports only
if the rate at which DHCP frames arrive is too high.
Untrust
Use this to set un-trusted ports.
Untrusted ports are connected to subscribers, and the MES-2110
discards DHCP frames from untrusted ports in the following
situations:
144
The frame is a DHCP server frame (for example, OFFER, ACK,
or NACK).
The source MAC address and source IP address in the frame
do not match any of the current bindings.
The frame is a RELEASE or DECLINE frame, and the source
MAC address and source port do not match any of the current
bindings.
The rate at which DHCP frames arrive is too high.
All Port
Use this to configure all ports as trusted or un-trusted ports.
Undo
Click this to reset the values in this screen to their last-saved
values.
MES-2110 Users Guide
Chapter 19 IP Source Guard
Table 53 Configuration > IP Source Guard > DHCP > DHCP Snooping Configuration
(continued)
LABEL
DESCRIPTION
Apply
Click Apply to save your changes to the MES-2110s run-time
memory. The MES-2110 loses these changes if it is turned off or
loses power, so use the Save link on the top navigation panel to
save your changes to the non-volatile memory when you are
done configuring.
DHCP Snooping Status
Action
This shows whether DHCP snooping is enabled or disabled.
DHCP snooping VLAN
Mode
This shows whether the MES-2110 forwards DHCP frames of any
VLANs or specific VLANs to DHCP servers.
DHCP Snooping
Option
This specifies whether or not the MES-2110 enabled or disabled
adding DHCP relay agent option 82 information to DHCP requests
that the MES-2110 relays to a DHCP server for each VLAN.
Option82 Information
This indicates the remote ID of the DHCP relay agent.
DHCP VLAN (Fixed)
This shows the specific VLAN ID.
Trust/Untrust
This shows whether the port is trusted or un-trusted.
19.3 DHCP Binding Table
Bindings are used by DHCP snooping and ARP inspection to distinguish between
authorized and unauthorized frames in the network. The MES-2110 learns the
bindings by snooping DHCP frames (dynamic bindings) and from information
provided manually by administrators (static bindings).
Use this screen to manage static bindings for DHCP snooping and ARP inspection.
Static bindings are uniquely identified by the MAC address and VLAN ID. Each MAC
address and VLAN ID can only be in one static binding. If you try to create a static
binding with the same MAC address and VLAN ID as an existing static binding, the
MES-2110 Users Guide
145
Chapter 19 IP Source Guard
new static binding replaces the original one. Click Configuration > DHCP
Snooping > DHCP Binding Table to open the following screen.
Figure 67 Configuration > DHCP Snooping > DHCP Binding Table
The following table describes the labels in this screen.
Table 54 Configuration > DHCP Snooping > DHCP Binding Table
LABEL
DESCRIPTION
DHCP Binding Configuration
MAC Address
Enter the source MAC address in the binding.
IP Address
Enter the IP address assigned to the MAC address in the binding.
Port
Specify the port in the binding.
VLAN ID
Specify a VLAN ID if you want the MES-2110 to forward DHCP
frames to DHCP servers on a specific VLAN.
Leave the field blank if you do not want the MES-2110 to forward
DHCP frames to a specific VLAN.
Undo
Click this to restore your last saved settings
Add
Click this to add the rule to the MES-2110.
Static/Dynamic Binding Table
146
No.
This field displays a sequential number for each binding.
Port
This field displays the port number in the binding.
VLAN ID
This field displays the source VLAN ID in the binding.
MAC Address
This field displays the source MAC address in the binding.
IP Address
This field displays the IP address assigned to the MAC address in
the binding.
Delete
Click this to delete a static binding rule.
Lease Time
(DD:HH:MM)
This field displays how many days, hours and minutes the binding
is valid; for example, 02:03:04 means the binding is still valid for
2 days, 3 hours and 4 minutes.
MES-2110 Users Guide
Chapter 19 IP Source Guard
19.4 The ARP Inspection Screen
Use ARP inspection to filter unauthorized ARP frames on the network. This can
prevent many kinds of man-in-the-middle attacks, such as the one in the following
example.
Figure 68 Example: Man-in-the-middle Attack
In this example, computer B tries to establish a connection with computer A.
Computer X is in the same broadcast domain as computer A and intercepts the
ARP request for computer A. Then, computer X does the following things:
It pretends to be computer A and responds to computer B.
It pretends to be computer B and sends a message to computer A.
As a result, all the communication between computer A and computer B passes
through computer X. Computer X can read and alter the information passed
between them.
19.4.1 Configuring ARP Inspection
Follow these steps to configure ARP inspection on the MES-2110.
1
Configure DHCP snooping. See Section 19.1.1.3 on page 142.
Note: It is recommended you enable DHCP snooping at least one day before you
enable ARP inspection so that the MES-2110 has enough time to build the
binding table.
2
Enable ARP inspection on the MES-2110. See Section 19.4 on page 147 for more
details about turning on this feature.
MES-2110 Users Guide
147
Chapter 19 IP Source Guard
Click IP Source Guard > ARP Inspection > ARP Inspection Config to open
the following screen.
Figure 69 Configuration > ARP Inspection
The following table describes the labels in this screen.
Table 55 Configuration > ARP Inspection
LABEL
DESCRIPTION
ARP Inspection
148
Action
Use this to enable or disable the ARP inspection feature.
MAC-Filter-AgingTime
Enter the number of minutes from 1-10080 that the MES-2110
retains MAC addresses in its MAC address table. Enter 0 to retain
addresses permanently.
MES-2110 Users Guide
Chapter 19 IP Source Guard
Table 55 Configuration > ARP Inspection
LABEL
DESCRIPTION
ARP Inspection VLAN
Mode
Select All-VLAN to have the Switch look at all the VLANs on
which ARP inspection is enabled.
Select Fixed to have the Switch look at the specific VLANs on
which ARP inspection in enabled..
ARP Inspection VLAN
(Fixed)
Enter the ID of a static VLAN; the valid range is between 1 and
4094.
Action
This is the port number.
Trust
Use this to set trust ports.
Untrust
Use this to set un-trusted ports.
All Port
Use this to configure all ports as trusted or un-trusted ports.
ARP Inspection Status
Action
This shows whether the ARP inspection feature is enabled or
disabled on the MES-2110.
MAC-Filter-AgingTime
This shows the number of minutes that the MES-2110 retains
MAC addresses in its MAC address table.
ARP Inspection VLAN
Mode
This shows whether the MES-2110 look at all VLANs or specific
VLANs on which ARP inspection in enabled.
ARP Inspection VLAN
(Fixed)
This shows the specific VLAN ID.
Trust/Untrust
This shows whether the port is trusted or un-trusted.
MES-2110 Users Guide
149
Chapter 19 IP Source Guard
150
MES-2110 Users Guide
CHAPTER
20
MAC
20.1 Overview
The MAC Table screen (a MAC table is also known as a filtering database) shows
how frames are forwarded or filtered across the MES-2110s ports. It shows what
device MAC address, belonging to what VLAN group (if any) is forwarded to which
port(s) and whether the MAC address is dynamic (learned by the MES-2110) or
static (manually entered in the Static MAC Forwarding screen).
The MES-2110 uses the MAC table to determine how to forward frames. See the
following figure.
1
The MES-2110 examines a received frame and learns the port on which this
source MAC address came.
The MES-2110 checks to see if the frame's destination MAC address matches a
source MAC address already learned in the MAC table.
If the MES-2110 has already learned the port for this MAC address, then it
forwards the frame to that port.
If the MES-2110 has not already learned the port for this MAC address, then the
frame is flooded to all ports. Too much port flooding leads to network
congestion.
MES-2110 Users Guide
151
Chapter 20 MAC
If the MES-2110 has already learned the port for this MAC address, but the
destination port is the same as the port it came in on, then it filters the frame.
Figure 70 MAC Table Flowchart
20.2 The MAC Table Status Screen
Use this screen to configure the MAC aging time and view the MAC table. Click
Configuration > MAC Menu > MAC Table Status to open the following screen.
Figure 71 Configuration > MAC Menu > MAC Table Status
The following table describes the labels in this screen.
Table 56 Configuration > MAC Menu > MAC Table Status
LABEL
DESCRIPTION
MAC Table Configuration
152
MAC aging time
Enter a time from 16 to 4080 seconds. This is how long all
dynamically learned MAC addresses remain in the MAC address
table before they age out (and must be relearned).
MAC aging time
This is the current MAC aging time.
MES-2110 Users Guide
Chapter 20 MAC
Table 56 Configuration > MAC Menu > MAC Table Status
LABEL
DESCRIPTION
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MAC Table Status
No.
This is the incoming frame index number.
MAC Address
This is the MAC address of the device from which this incoming
frame came.
Static
This shows whether the MAC address is dynamic (learned by the
MES-2110) or static (manually configured).
Priority
This shows the priority level of the MAC address
1-10
This shows the port from which the MAC address was learned.
Page Up/Down
Click this to view the previous or next page.
20.3 The Lock MAC Address Learning Screen
Use this screen to configure the MAC address learning settings. Click
Configuration > MAC Menu > Lock Learning MAC to open the following
screen.
Figure 72 Configuration > MAC Menu > Lock Learning MAC
MES-2110 Users Guide
153
Chapter 20 MAC
The following table describes the labels in this screen.
Table 57 Configuration > MAC Menu > Lock Learning MAC
LABEL
DESCRIPTION
Port
This is the port number.
Lock
MAC address learning reduces outgoing broadcast traffic. Use this
to activate MAC address learning on the port.
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
20.4 The MAC Filter Configuration Screen
Use this screen to configure and view the MAC filter settings. Click Configuration
> MAC Menu > MAC Filter Config to open the following screen.
Figure 73 Configuration > MAC Menu > MAC Filter Config
154
MES-2110 Users Guide
Chapter 20 MAC
The following table describes the labels in this screen.
Table 58 Configuration > MAC Menu > MAC Filter Config
LABEL
DESCRIPTION
MAC Filter Configuration
Status
Use this to determine whether to allow or deny traffic transmitted
from the source MAC address.
Port
Select the port through which traffic from the source MAC address
is transmitted.
Priority
Select a priority level from 0 to 7.
Pri-Override
Use this to ignore the priority level assigned to the transmitted
frames.
MAC Address
Type a MAC address in valid MAC address format, that is, six
hexadecimal character pairs.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
Allowed Table
Port
This is the port number through which traffic from the source MAC
address is transmitted.
MAC Address
This is the source MAC address.
Priority
This shows the priority level.
Pri-Override
This shows whether priority level override is enabled or disabled.
Delete
Click this to remove the rule.
Page Up/Down
Click this to view the previous or next page.
Denied Table
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MAC Address
This is the source MAC address.
Delete
Click this to remove the rule.
Page Up/Down
Click this to view the previous or next page.
MES-2110 Users Guide
155
Chapter 20 MAC
20.5 The MAC Limit Configuration Screen
Use this screen to limit the number of MAC addresses that can be learned on a
port. Click Configuration > MAC Menu > MAC Limit Config to open the
following screen.
Figure 74 Configuration > MAC Menu > MAC Limit Config
The following table describes the labels in this screen.
Table 59 Configuration > MAC Menu > MAC Limit Config
LABEL
DESCRIPTION
MAC Limit Function
Use this to enable or disable the MAC address limit feature.
Port
This is the port number.
Limit Quantity
Use this field to limit the number of (dynamic) MAC addresses
that may be learned on a port. For example, if you set this field to
"5" on port 2, then only the devices with these five learned MAC
addresses may access port 2 at any one time. A sixth device
would have to wait until one of the five learned MAC addresses
aged out. MAC address aging out time can be set in the MAC
Table Status screen.
Action
Enable the MAC limit function on this port. The MES-2110
forwards frames whose MAC address(es) is in the MAC address
table on this port. frames with no matching MAC address(es) are
dropped.
Disable the MAC limit function to forwards all frames on this port.
156
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
CHAPTER
21
QoS
21.1 Overview
Quality of Service (QoS) is used to prioritize source-to-destination traffic flows. All
frames in the flow are given the same priority. You can use QoS to give different
priorities to different frame types to solve performance degradation when there is
network congestion.
21.2 The QoS Base Configuration Screen
Queuing algorithms allow switches to maintain separate queues for frames from
each individual source or flow and prevent a source from monopolizing the
bandwidth.
All High Before Low Queuing
All high before low services queues based on priority only. As traffic comes into
the MES-2110, traffic on the highest priority queue, Q7 is transmitted first. When
that queue empties, traffic on the next highest-priority queue, Q6 is transmitted
until Q6 empties, and then traffic is transmitted on Q5 and so on. If higher priority
queues never empty, then traffic on lower priority queues never gets sent. SP
does not automatically adapt to changing network requirements.
Weighted Round Robin Scheduling (WRR)
Round Robin Scheduling services queues on a rotating basis and is activated only
when a port has more traffic than it can handle. A queue is a given an amount of
bandwidth irrespective of the incoming traffic on that port. This queue then moves
to the back of the list. The next queue is given an equal amount of bandwidth, and
then moves to the end of the list; and so on, depending on the number of queues
being used. This works in a looping fashion until a queue is empty.
Weighted Round Robin Scheduling (WRR) uses the same algorithm as round robin
scheduling, but services queues based on their priority rather than a fixed amount
of bandwidth. WRR is activated only when a port has more traffic than it can
MES-2110 Users Guide
157
Chapter 21 QoS
handle. Queues with larger weights get more service than queues with smaller
weights. This queuing mechanism is highly efficient in that it divides any available
bandwidth across the different traffic queues and returns to queues that have not
yet emptied.
21.2.1 Configuring the Base Configuration Screen
Use this screen to configure queuing settings on the MES-2110. Click
Configuration > QoS Menu > Base Configuration to open the following
screen.
Figure 75 Configuration > QoS Menu > Base Configuration
The following table describes the labels in this screen.
Table 60 Configuration > QoS Menu > Base Configuration
LABEL
DESCRIPTION
QoS Base Configuration
Schedule Mode
Select all high before low or weighted round robin.
All high before low queues based on priority only. When the
highest priority queue empties, traffic on the next highest-priority
queue begins. Q7 has the highest priority and Q0 the lowest.
Weighted Round Robin Scheduling services queues on a rotating
basis based on their queue weight. Queues with larger weights
get more service than queues with smaller weights.
158
MES-2110 Users Guide
Chapter 21 QoS
Table 60 Configuration > QoS Menu > Base Configuration
LABEL
DESCRIPTION
Port
This label shows the port you are configuring.
Priority Mode
Select a priority mode for the port.
802.1p Priority uses port priority as queuing basis. Assign a
priority level to each port in the 802.1p Priority screen (Section
21.3 on page 160).
Tag Priority uses VLAN tag priority as queuing basis. See
Section 21.4 on page 161 for more details on configuring tag
priority.
IP ToS Priority uses IP DSCP priority as queuing basis. See
Section 21.5 on page 161 for more details on configuring IP DSCP
priority.
IP & Tag Priority uses both IP DSCP priority and tag priority as
queuing basis.
IP Over Tag
Use this to enable or disable IP Over Tag on the port.
When you enable this feature and the MES-2110 receives a frame
containing both IP DSCP and tag priority information, the MES2110 will only use the IP DSCP priority information.
All Port
Use this to set the priority mode for all ports.
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
QoS Base Status
Port1-10
This is the port number.
Schedule
This is the schedule mode used on the MES-2110.
Priority Mode
This is the priority mode used on the port.
IP Over Tag
This shows whether the IP over tag feature is enabled or disabled
on the MES-2110.
MES-2110 Users Guide
159
Chapter 21 QoS
21.3 The 802.1p Priority Table
Use this screen to assign a priority level for each port. Click Configuration > QoS
Menu > 802.1p Priority to open the following screen.
Figure 76 Configuration > QoS Menu > 802.1p Priority
The following table describes the labels in this screen.
Table 61 Configuration > QoS Menu > 802.1p Priority
160
LABEL
DESCRIPTION
Port
This label shows the port you are configuring.
Priority
Assign a priority level to the port.
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
Chapter 21 QoS
21.4 The Tag Priority Table
Click Configuration > QoS Menu > Tag Priority to open the following screen.
Figure 77 Configuration > QoS Menu > Tag Priority
The following table describes the labels in this screen.
Table 62 Configuration > QoS Menu > Tag Priority
LABEL
DESCRIPTION
Number
This is the IEEE 802.1p priority level.
Priority
Use this to assign the tag priority level to one of the MES-2110s
queue level (Low, Normal, Preferred or High).
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
21.5 The IP DSCP Priority Table
DiffServ is a class of service (CoS) model that marks frames so that they receive
specific per-hop treatment at DiffServ-compliant network devices along the route
based on the application types and traffic flow. Frames are marked with DiffServ
Code Points (DSCPs) indicating the level of service desired. This allows the
intermediary DiffServ-compliant network devices to handle the frames differently
depending on the code points without the need to negotiate paths or remember
state information for every flow. In addition, applications do not have to request a
particular service or give advanced notice of where the traffic is going.
MES-2110 Users Guide
161
Chapter 21 QoS
Use this to assign DSCP priority settings. Click Configuration > QoS Menu > IP
DSCP Priority to open the following screen.
Figure 78 Configuration > QoS Menu > IP DSCP Priority
The following table describes the labels in this screen.
Table 63 Configuration > QoS Menu > IP DSCP Priority
162
LABEL
DESCRIPTION
Number
Enter the DSCP classification identification number (0-63).
Priority
Assign a MES-2110s priority level (Low, Normal, Preferred or
High) to the DSCP value.
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
Chapter 21 QoS
21.6 The Priority Override Configuration Screen
Use this screen to apply the QoS settings of the MES-2110 to its DHCP clients. The
MES-2110 ignores the priority levels assigned to the transmitted frames on the ports,
source MAC addresses and destination MAC addresses.
Click Configuration > QoS Menu > Priority Override Configuration to open
the following screen.
Figure 79 Configuration > QoS Menu > Priority Override Configuration
The following table describes the labels in this screen.
Table 64 Configuration > QoS Menu > Priority Override Configuration
LABEL
DESCRIPTION
Port
This label shows the port you are configuring.
VID-Pri-Override
Select Enable to have the MES-2110 ignore the priority level
assigned to the transmitted frames on this port.
Select Disable if you do not want to use this feature. This is
selected by default.
Destination-MAC-PriOverride
Select Enable to have the MES-2110 ignore the priority level
assigned to the transmitted frames on the destination MAC
address.
Select Disable if you do not want to use this feature. This is
selected by default.
Source-MAC-PriOverride
Select Enable to have the MES-2110 ignore the priority level
assigned to the transmitted frames on the source MAC address.
Select Disable if you do not want to use this feature. This is
selected by default.
MES-2110 Users Guide
163
Chapter 21 QoS
Table 64 Configuration > QoS Menu > Priority Override Configuration
164
LABEL
DESCRIPTION
Undo
Click this to load your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
CHAPTER
22
Mgmt Config and System
Restart Menu
22.1 Overview
This chapter explains how to configure the screens that let you maintain the
firmware and configuration files.
22.2 The Serial Port Configuration Screen
Use this screen to view the parameters for local management. Configure a
computers terminal emulation software with the displayed parameters to manage
the MES-2110. Connect the male 9-pin end of the console cable to the console
port of the MES-2110. Connect the female end to a serial port (COM1, COM2 or
other COM port) of your computer.
Click Mgmt Config > Serial Port Config to open the following screen.
Figure 80 Mgmt Config > Serial Port Config
Specify the amount of time (in seconds) before the console session disconnects
automatically. If you set the timeout to 0 second, the console session never
expires. Click Apply to save your changes.
MES-2110 Users Guide
165
Chapter 22 Mgmt Config and System Restart Menu
22.3 The SNMP Configuration Screens
Simple Network Management Protocol (SNMP) is an application layer protocol
used to manage and monitor TCP/IP-based devices. SNMP is used to exchange
management information between the network management system (NMS) and a
network element (NE). A manager station can manage and monitor the MES-2110
through the network via SNMP version one (SNMPv1), SNMP version 2c or SNMP
version 3. The next figure illustrates an SNMP management operation. SNMP is
only available if TCP/IP is configured.
Figure 81 SNMP Management Model
An SNMP managed network consists of two main components: agents and a
manager.
An agent is a management software module that resides in a managed switch (the
MES-2110). An agent translates the local management information from the
managed switch into a form compatible with SNMP. The manager is the console
through which network administrators perform network management functions. It
executes applications that control and monitor managed devices.
The managed devices contain object variables/managed objects that define each
piece of information to be collected about a switch. Examples of variables include
number of packets received, node port status and so on. A Management
Information Base (MIB) is a collection of managed objects. SNMP allows a
manager and agents to communicate for the purpose of accessing these objects.
166
MES-2110 Users Guide
Chapter 22 Mgmt Config and System Restart Menu
SNMP itself is a simple request/response protocol based on the manager/agent
model. The manager issues a request and the agent returns responses using the
following protocol operations:
Table 65 SNMP Commands
COMMAND
DESCRIPTION
Get
Allows the manager to retrieve an object variable from the agent.
GetNext
Allows the manager to retrieve the next object variable from a table or list
within an agent. In SNMPv1, when a manager wants to retrieve all
elements of a table from an agent, it initiates a Get operation, followed by a
series of GetNext operations.
Set
Allows the manager to set values for object variables within an agent.
Trap
Used by the agent to inform the manager of some events.
22.3.1 The SNMP Communities Screen
Use this screen to configure the SNMP communities. Click Mgmt Config > SNMP
Config > SNMP Communities to open the following screen.
Figure 82 Mgmt Config > SNMP Config > SNMP Communities
The following table describes the labels in this screen.
Table 66 Mgmt Config > SNMP Config > SNMP Communities
LABEL
DESCRIPTION
GET
Enter the Get community string, which is the password for the
incoming Get- and GetNext- requests from the management
station.
SET
Enter the Set community string, which is the password for
incoming Set- requests from the management station.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
22.3.2 The IP Trap Manager Screen
An IP trap manager receives authentication failure messages or other trap
messages about the MES-2110s activities. The MES-2110 supports up to five trap
MES-2110 Users Guide
167
Chapter 22 Mgmt Config and System Restart Menu
managers. Use this screen to configure the trap manager settings. Click Mgmt
Config > SNMP Config > IP Trap Manager to open the following screen.
Figure 83 Mgmt Config > SNMP Config > IP Trap Manager
The following table describes the labels in this screen.
Table 67 Mgmt Config > SNMP Config > IP Trap Manager
LABEL
DESCRIPTION
IP Address
Enter the IP addresses of up to five managers to send your SNMP
traps to.
Community Name
Enter the community string.
Status
Use this to enable or disable the trap manager feature.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
22.4 The SNTP Screen
Use this screen to configure the time settings on the MES-2110. You can configure
the MES-2110 to get the time and date information from a time server using
Simple Network Time Protocol (SNTP). You can also configure two servers. If the
first one is down, the MES-2110 will try to connect to the second one.
168
MES-2110 Users Guide
Chapter 22 Mgmt Config and System Restart Menu
Click Mgmt Config > SNTP to open the following screen.
Figure 84 Mgmt Config > SNTP
The following table describes the labels in this screen.
Table 68 Mgmt Config > SNTP
LABEL
DESCRIPTION
SNTP Status
Use this to enable or disable time server for the MES-2110.
SNTP Server 1 and 2
Enter the IP address of your time server.
SNTP Request Interval
Specify how often (in hours) should the MES-2110 synchronize
with the time server.
For example, if you set the field to 2 hours, the MES-2110
synchronizes date/time with the time server every 2hours.
Current Time
Specify the date (in year, month and day format) and time (in
hour, minute and second format).
Time Zone
Select the time difference between UTC (Universal Time
Coordinated, formerly known as GMT, Greenwich Mean Time)
and your time zone.
Day Light Saving
Daylight saving is a period from late spring to early fall when
many countries set their clocks ahead of normal local time by
one hour to give more daytime light in the evening.
Enable this option if you use Daylight Saving Time.
Day Light Saving Start
Configure the day and time when Daylight Saving Time starts if
you selected Daylight Saving Time. The time is displayed in
the 24 hour format. Here are a couple of examples:
Daylight Saving Time starts in most parts of the United States
on the second Sunday of March. Each time zone in the United
States starts using Daylight Saving Time at 2 A.M. local time.
Youll have to manually configure the date every year as the
date changes every year.
MES-2110 Users Guide
169
Chapter 22 Mgmt Config and System Restart Menu
Table 68 Mgmt Config > SNTP
LABEL
DESCRIPTION
Day Light Saving End
Configure the day and time when Daylight Saving Time ends if
you selected Daylight Saving Time. The time field uses the 24
hour format. Here are a couple of examples:
Daylight Saving Time ends in the United States on the first
Sunday of November. Each time zone in the United States stops
using Daylight Saving Time at 2 A.M. local time. Youll have to
manually configure the date every year as the date changes
every year.
Undo
Click this to restore your last saved settings.
Refresh
Click this to reset the data for the field(s).
Apply
Click Apply to save your changes to the ZyXEL Devices runtime memory. The ZyXEL Device loses these changes if it is
turned off or loses power, so use the Save Settings link in the
navigation panel to save your changes to the non-volatile
memory.
22.5 Alarms and Logs
Use this screen to configure the mail server, the syslog and alarm settings. Click
Mgmt Config > Email Alarm & SYSLog Config to open the following screen.
Figure 85 Mgmt Config > Email Alarm & SYSLog Config
170
MES-2110 Users Guide
Chapter 22 Mgmt Config and System Restart Menu
The following table describes the labels in this screen.
Table 69 Mgmt Config > Email Alarm & SYSLog Config
LABEL
DESCRIPTION
Email Alarm Configuration
Email Alarm
Use this to enable or disable the e-mail alarm system.
Mail Server IP
Enter the server name or the IP address of the mail server for the
e-mail addresses specified below. If this field is left blank, logs
and alerts messages will not be sent via e-mail.
From
Assign a valid e-mail address to the MES-2110.
To
The MES-2110 sends logs to the e-mail addresses specified in this
field. If this field is left blank, the MES-2110 does not send logs
via e-mail.
SYSLOG
SYSLOG Status
Use this to enable or disable syslog logging.
Backup
Click this save syslog file to a TFTP server.
Show
Click this to show a complete list of syslog messages.
Alarm Type
Select the categories of alarm that you want to record and send
an e-mail alarm.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
171
Chapter 22 Mgmt Config and System Restart Menu
22.6 The User Configuration Screen
Use this screen to configure user names, passwords and access right for up to five
user accounts. Click Mgmt Config > User Config to open the following screen.
Note: It is recommended that only one user log in and manage the device at a time.
When multiple users configure the device settings simultaneously, changes
may be overwritten.
Figure 86 Mgmt Config > User Config
The following table describes the labels in this screen.
Table 70 Mgmt Config > User Config
LABEL
DESCRIPTION
User Name
Enter a name to identify the user account. You can type up to 15
characters using characters found on a standard keyboard.
User Password
Enter a password associated with the user name. You can type up
to 15 characters using characters found on a standard keyboard.
User-Level
Assign access rights for the user account.
Read/Write users can manage the MES-2110 settings as an
administrator.
Read Only users can only view the MES-2110 settings.
172
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
Chapter 22 Mgmt Config and System Restart Menu
22.7 The Cable Test Screen
Use this feature to diagnose the connection on each port. Click Mgmt Config >
Cable Test to open a dialogue box asking for your confirmation.
Click OK to start the test. The test results are shown as follows.
Figure 87 Mgmt Config > Host Denial-of-Service Protection
The following table describes the labels in this screen.
Table 71 Mgmt Config > Host Denial-of-Service Protection
LABEL
DESCRIPTION
Port
This is the port number.
PHY (RX/TX)
This shows if data is flowing through the ports on the MES-2110.
If no data is passing through a port, this shows Link-Down.
Otherwise, the number indicates the maximum size of packets
during data transmission in the port.
Test
If the cable is well connected to the port, this shows Pass.
Otherise, this shows Fail.
Status
If the cable is well connected to the port, this is Normal. If
the connection is down, you see an Open status.
MES-2110 Users Guide
173
Chapter 22 Mgmt Config and System Restart Menu
Table 71 Mgmt Config > Host Denial-of-Service Protection
LABEL
DESCRIPTION
CableLength
This shows the length of the cable connected to the port.
TEST
Click this to run the test again.
22.8 The Host DoS Protection
You can specify a group of one or more trusted computers from which an
administrator may use a service to manage the MES-2110. When you turn on this
feature, only the trusted IP addresses listed in this screen can use remote
management to access the MES-2110. Click Mgmt Config > Host Denial-ofService Protection to open the following screen.
Figure 88 Mgmt Config > Host Denial-of-Service Protection
The following table describes the labels in this screen.
Table 72 Mgmt Config > Host Denial-of-Service Protection
LABEL
DESCRIPTION
Protection
Use this to enable or disable host denial-of-service protection.
IP Address
Configure the IP address of the trusted computer from which you
can manage this MES-2110.
The MES-2110 checks if the client IP address of a computer
requesting a service or protocol matches the range set here. The
MES-2110 immediately disconnects the session if it does not
match.
Enable/Disable
Select Enable to activate this secured client set.
Select Disable if you wish to temporarily disable the set without
deleting it.
174
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
MES-2110 Users Guide
Chapter 22 Mgmt Config and System Restart Menu
22.9 The Port Abnormal Traffic Detection Screen
This MES-2110 can detect excessive broadcasts or transmission load on a port and
temporarily or permanently block traffic transmission on each port. Use this
screen to configure the MES-2110s threshold settings for blocking a port. You can
also have the Switch unblock a port when it is no longer receiving large broadcast
packets.
Click Mgmt Config > Port Abnormal Traffic Detection to open the following
screen.
Figure 89 Mgmt Config > Port Abnormal Traffic Detection
The following table describes the labels in this screen.
Table 73 Mgmt Config > Port Abnormal Traffic Detection
LABEL
DESCRIPTION
Protection
Use this to enable or disable abnormal traffic detection on the
MES-2110.
Abnormal Traffic
Set the rules for abnormal traffic in the fields described below.
Threshold
Specify a threshold value (in broadcast packets per second). If
transmission load on a port exceeds this threshold, the MES-2110
blocks the port. The block can be blocked permanently or for a
period of time, depending on what you specify in this screen (see
fields below).
MES-2110 Users Guide
175
Chapter 22 Mgmt Config and System Restart Menu
Table 73 Mgmt Config > Port Abnormal Traffic Detection
LABEL
DESCRIPTION
Detection Duration
Specify for how long (up to 60 seconds) the threshold is exceeded
before the MES-2110 blocks the port.
This allows the port(s) to exceed the threshold for a short time
period depending on the number of seconds you specify. The port
is blocked when the transmission load continues and the number
of seconds has expired.
If packet and duration threshold exceeded
Block port
permanently
Select Yes to block the port for good if traffic exceeds the
threshold for a certain time.
You can manually unblock a port in the Block/Unblock field.
However the port is only unblocked when it is not receiving
excessive traffic anymore.
If No, block for N
seconds
Specify for how long the MES-2110 will block the port if traffic
exceeds the threshold.
Port
This shows the port number(s) that you can configure.
Enable/Disable
If you enabled abnormal traffic detection on the MES-2110, use
this to enable or disable abnormal traffic detection on a specific
port.
The rules you set will only apply to ports that are set to Enable.
Block/Unblock
Use this field to manually block or unblock a port.
Select Block to have the Switch block a port according to the
abnormal traffic detection values you specified in this screen.
Select Unblock to have the Switch unblock a previously blocked
port when it is not receiving abnormal traffic anymore.
Undo
Click this to restore your last saved settings.
Apply
Click Apply to save your changes to the ZyXEL Devices run-time
memory. The ZyXEL Device loses these changes if it is turned off
or loses power, so use the Save Settings link in the navigation
panel to save your changes to the non-volatile memory.
22.10 Upgrading the Firmware
Make sure you have downloaded (and unzipped) the correct model firmware and
version to your computer before uploading to the device.
Be sure to upload the correct model firmware as uploading the
wrong model firmware may damage your device.
176
MES-2110 Users Guide
Chapter 22 Mgmt Config and System Restart Menu
Click Mgmt Config > Firmware Download to open the following screen.
Figure 90 Mgmt Config > Firmware Download
Type the path and file name of the firmware file you wish to upload to the MES2110 in the File Name field or click Browse to locate it. Click Start Upgrade to
load the new firmware.
After the firmware upgrade process is complete, the device will automatically
restart. See the System Details > Board Info. screen to verify your current
firmware version number.
22.11 Managing the Configuration File
Backing up your MES-2110 configurations allows you to create various snap
shots of your device from which you may restore at a later date. Use this screen
to back up or restore a configuration file. Click Mgmt Config > Configuration
File to open the following screen.
Figure 91 Mgmt Config > Configuration File
Follow the steps below to back up the current MES-2110 configuration to your
computer in this screen.
1
Click Backup Setting.
Choose a location to save the file on your computer from the Save in drop-down
list box and type a descriptive name for it in the File name list box. Click Save to
save the configuration file to your computer.
To restore a configuration file, type the path and file name of the configuration file
you wish to restore in the field or click Browse to locate it. After you have
specified the file, click Restore Setting. "config" is the name of the configuration
file on the MES-2110, so your backup configuration file is automatically renamed
when you restore using this screen.
MES-2110 Users Guide
177
Chapter 22 Mgmt Config and System Restart Menu
22.12 Restarting the System
Click System Restart Menu > Restart Option to open the following screen. Use
the Restore button to load the factory default settings, or use the Reset button to
restart the system without physically turning the power off. It also allows you to
load the factory default settings when you reboot.
Figure 92 System Restart Menu > Restart Option
178
MES-2110 Users Guide
CHAPTER
23
Command Line Interface
23.1 Overview
This chapter introduces the MES-2110s command line interface (CLI).
23.1.1 Console Port Management
To manage the MES-2110 using the CLI:
1
Connect your computer to the console port on the MES-2110 using the
appropriate cable.
Use terminal emulation software with the following settings:
SETTING
DEFAULT VALUE
Terminal Emulation
VT100
Baud Rate
9600
Parity
None
Number of Data Bits
Number of Stop Bits
Flow Control
None
Press [ENTER] to trigger the login screen.
23.1.2 Logging in
Use the administrator password to log into the MES-2110. The default value
administrator login username and password are: admin and 1234.
The MES-2110 automatically logs you out of the management interface after five
minutes of inactivity. If this happens, simply log back in again.
MES-2110 Users Guide
179
Chapter 23 Command Line Interface
23.1.3 Using Shortcuts and Getting Help
This table identifies some shortcuts in the CLI, as well as how to get help.
Table 74 CLI Shortcuts and Help
COMMAND / KEY(S)
DESCRIPTION
yz (up/down arrow keys)
Scrolls through the list of recently-used commands. You
can edit any command or press [ENTER] to run it again.
[CTRL]+U
Clears the current command.
Displays the keywords and/or input values that are
allowed in place of the ?.
There are 2 types of help in the MES-2110: descriptive
and parameter.
Descriptive help: This type of help displays a short
description of the command.
To display descriptive help, simply type command? with
no space between the commands final letter and the
question mark.
Parameter help: This type of help displays all available
parameters for the command in question.
To display parameter help, type command ? with a space
between the commands final letter and the question
mark. In some cases, commands do not have any
parameters and typing this results in the command being
carried out.
help
Displays the (full) commands that are allowed in place of
help.
23.2 Saving Changes
In the MES-2110, whenever you make changes using the command line interface
they are not saved by default.
To save your changes, you must use the following commands starting in Basic
command mode (for details on this mode, see Section 23.5 on page 182):
MES-2110> enable
MES-2110# write memory
It takes a few moments to write memory...
MES-2110#
180
MES-2110 Users Guide
Chapter 23 Command Line Interface
23.3 Logging Out
Enter exit to log out of the CLI while in Basic mode.
Table 75 Exit Command
COMMAND
DESCRIPTION
exit
Logs you out of the CLI while in Basic mode. If
in any other mode, then this command returns
you to the previous mode.
23.4 Command Modes
The MES-2110 segregates commands by command mode. Commands for a
particular mode are only available once you set the device to that particular mode.
The following is list of available command modes.
Table 76 Basic Commands
MODE
TRIGGER
DESCRIPTION
Basic
Log in.
This is the default command line interface
mode when you log into the device.
Commands are restricted in this mode.
See Section 23.5 on page 182 for details.
Privileged
Configuration
While in Basic mode, type enable at
the prompt and then press
[ENTER].
This mode a limited command set for
configuring some of the MES-2110s features.
While in Privileged mode:
This mode allows to you configure all of the
MES-2110s advanced options.
Type configure terminal at the
prompt and then press [ENTER].
See Section 23.6 on page 183 for details.
Configuration mode also has 3 ancillary
modes: MVR, VLAN, and Interface.
See Section 23.7 on page 186 for details.
MES-2110 Users Guide
181
Chapter 23 Command Line Interface
23.5 Basic Commands
Basic commands are in all modes.
When in Basic mode, the command prompt is as follows:.
MES-2110>
The following is a list of available Basic commands:
Table 77 Basic Commands
COMMAND
DESCRIPTION
exit
In Basic mode, this disconnects you from the
device (identical to logout).
In other modes (such as Privileged), this returns
you to the previous mode.
help
Lists available commands.
history
Displays a list of previously run commands.
logout
Disconnects from the device.
ping <-n count> <-l length> <-t> <-w
timeout> <ip-address>
Pings the specied IP address.
You can use the following parameters:
-n count: Determines the number of echo
requests to send. The default is 4.
-l length: Adjusts the size of the ping packet
by the number of specified bytes (64~8148).
-t: Pings the specified host until the break
(ESC) key is pressed.
-w timeout: Adjusts the timeout duration for
the ping packet in milliseconds. The default is
1,000 milliseconds.
show ip
Displays the devices network configuration.
show system-information
Shows the devices system configuration.
182
MES-2110 Users Guide
Chapter 23 Command Line Interface
23.6 Privileged Command Mode
When in Privileged mode, the command prompt is as follows:.
MES-2110#
The following is a list of Privileged mode commands:
Table 78 Privileged Commands
COMMAND
DESCRIPTION
enable
Turns on Privileged mode commands.
disable
Turns off Privileged mode commands, returning
the device to Basic mode.
copy config tftp <ip-address> <file-name>
Uploads a configuration file from the specified
TFTP servers IP address.
copy firmware tftp <ip-address> <filename>
Uploads a firmware file from the specified TFTP
servers IP address.
copy syslog tftp <ip-address> <file-name>
Uploads a syslog file from the specified TFTP
servers IP address.
copy tftp command-text <ip-address> <filename>
Downloads a command file from the specified
TFTP servers IP address.
copy tftp config <ip-address> <file-name>
Downloads a configuration filefrom the specified
TFTP servers IP address.
copy tftp firmware <ip-address> <remotefile-name>
Downloads a firmware file from the specified
TFTP servers IP address.
reset default
Resets the device to its factory default settings.
reset system
Resets the system.
show abnormal
Displays the abnormal traffic detection
configuration.
show arp inspection <config|status>
Displays ARP inspection information.
config: Displays the ARP inspection
configuration file.
status: Displays the ARP inspection records.
show bandwidth-control
Diplays the bandwidth control information.
show cable <all|port-number>
Displays the cable test results. Select all to view
all test result or test by a specific port number.
show 8021p-priority
Displays the 8021p priority configuration for all
ports.
show console-baudrate
Displays the baud rate of the console port.
show console-timeout
Displays the number of idle seconds allowed on
the console port before the device automatically
terminates the session.
show dhcp smart-relay
Displays DHCP smart relay information.
show dhcp snooping
Displays DHCP snooping information.
MES-2110 Users Guide
183
Chapter 23 Command Line Interface
Table 78 Privileged Commands
COMMAND
DESCRIPTION
show dhcp static-binding
Displays the DHCP static binding table.
show dhcp dynamic-binding
Displays the DHCP dynamic binding table.
show dot1x global
Displays 802.1x global information.
show dot1x radius-server
Displays the 802.1x RADIUS server
configuration.
show dot1x port-control
Displays the 802.1x port-control information.
show email-alarm
Displays the email configuration.
show frame
Displays the maximum frame size configuration.
show hdos
Displays the Denial-of-Service configuration.
show igmp
Displays the igmp configuration.
show interface
Display detailed port information for all ports.
show LACP
Displays LACP information.
show locked-mac
Displays the locked MAC address learning status.
show logins
Displays a list of recent logins.
show loop
Displays the loop detection configuration.
show mac
Displays the MAC table.
show mac-aging-time
Displays the MAC aging time.
show mac-filter-table
Displays the MAC filter table.
show mac-limit
Displays the MAC limit table.
show mirror
Displays the mirror configuration.
show mvr
Displays multicast status, including the port
number, VLAN ID and multicast group members
on the switch. Optionally, displays the type of
each multicast VLAN.
show priority-override
Displays the priority override status table.
show qinq-sp-tpid
Displays the Server Provider Tag Prototol
Identifier.
show qos priority-mode
Displays QoS priority-mode and IP-over-tag
settings.
show qos default-priority-queue
Displays the QoS port priority.
show qos tag-priority-queue
Displays the QoS tag priority.
show qos ip-tos-pri-queue
Displays the QoS IP-TOS priority to queue
mapping.
show qos schedule
Displays the QoS schedule type.
show rmon port [+n | all]
Displays the devices RMON information.
+n: Enter plus sign followed by port number to
display just that ports information. For example,
show rmon port +1. You can also chain
multiple port numbers together, such as show
rmon port +1+2+6 (which displays information
for just ports 1, 2, and 6).
all: Displays RMON information for all ports.
184
MES-2110 Users Guide
Chapter 23 Command Line Interface
Table 78 Privileged Commands
COMMAND
DESCRIPTION
show rstp
Displays the RSTP configuration.
show sfp ddmi port <port-number>
Displays the SFP fiber port DDMI information for
the specified port.
show sfp serial-no port <port-number>
Displays the SFP serial number for the specified
port.
show sfp vendor port <port-number>
Displays the SFP vendor name for the specified
port.
show snmp
Displays the snmp configuration.
show sntp
Displays the SNTP configurations.
show sntp-timezone
Displays a list of time zones and their GMT offset.
show storm-control
Displays the storm control configuration.
show syslog [<begin:end>]
Displays all syslog messages.
You can also specify a range of syslog messages.
begin: Enter the first syslog message to display.
end: Enter the last syslog message to display.
show syslog-config
Displays the syslog configuration.
show version
Displays the system version.
show vlan port-base
Displays the port-base VLAN.
show vlan stacking
Displays the VLAN stacking status.
show vlan tag-base management-VLAN
Displays the VLAN for the management switch.
show vlan tag-base vlan-id
Displays the tag-base VLAN ID.
show vlan tag-base port-info
Displays the tag-base port information.
show vlan tag-base vlan-table
Displays tag-base VLAN table.
show vlan type
Displays the VLAN type.
write memory
Saves the current configuration, including all
changes made since the last save, to flash.
Note: You must use this command to
permanently save any changes you
make while using the MES-2110
command line interface.
MES-2110 Users Guide
185
Chapter 23 Command Line Interface
23.7 Configuration Mode
When in Configuration mode, the command prompt is as follows:.
MES-2110(config)#
There are 3 additional ancillary available while in Configuration mode. They are:
Table 79 Basic Commands
ANCILLARY
TRIGGER
DESCRIPTION
MVR
While in Configuration mode:
This mode allows to configure the MES-2110s
MVR IDs and their associated options.
Type mvr <1-4094> (where 1-4094)
is the MVR ID ranging from 1 to
4094) at the command line prompt
and then press [ENTER].
See Section 23.8 on page 195 for details.
If no MVR exists, then this creates
one for you.
VLAN
While in Configuration mode:
Type vlan <1-4094> (where 1-4094
is a VLAN ID ranging from 1 to 4094)
at the command line prompt and
then press [ENTER].
This mode allows you to configure the MES2110s VLAN IDs and their associated options.
See Section 23.9 on page 197 for details.
If no VLAN ID exists, then this
creates one for you.
Interface
While in Configuration mode:
This mode allows you to configure the MES2110s port interfaces and their associated
options.
Type interface <port> (where port
is a port number) at the command
line prompt and then press [ENTER] See Section 23.10 on page 198 for details.
The following is a list of baseline Configuration mode commands:
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
configure terminal
Toggles the Configuration mode, but only if you
are first in Privileged mode.
abnormal detection <enable|disable>
Enables or disables abnormal traffic detection.
abnormal duration <1-60>
Sets the abnormal traffic detection duration in
seconds (1-60).
abnormal interval <1-600>
Sets the protection interval in seconds (1-600).
abnormal permanently <yes|no>
Blocks any port permanently when abnormal
traffic is detected and this option is set to yes.
abnormal threshold <2000-20000>
Sets the threshold of traffic detection in packets
per second (2000-20,000).
186
MES-2110 Users Guide
Chapter 23 Command Line Interface
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
arp inspection enable
Enables ARP inspection.
Note: You must still enable ARP inspection
on specific VLAN and specify trusted
ports if you use this option.
arp inspection vlan <1-4094>
Sets the ARP inspection VLAN ID.
arp inspection vlan-mode <all|fixed>
Sets the ARP inspection VLAN mode.
arp inspection mac-filter-aging <0-10080>
Specifies how long (in minutes) MAC address
filters remain in the device after it identifies an
unauthorized ARP packet.
The device automatically deletes the MAC
address filter afterwards. Use 0 in the
parameter field to make it permanent.
console-baudrate <9600|19200|38400>
Sets the console ports baudrate.
console-timeout <0|10~3600>
Sets the console timeout in seconds.
0: Sets the console to never timeout
10~3600: Sets the console timeout in seconds
(minimum 10 seconds, maximum 3600 seconds,
default 300 seconds.)
dhcp binding <mac-address> <ip-address>
<port> <vlan-id>
Adds the specified MAC address, IP address,
port numer, and VLAN ID to the DHCP snooping
static binding table.
dhcp client
Enables DHCP client.
dhcp option-information <remote-id>
Sets the DHCP Option Remote ID.
remote-id: Enter a maximum of 64
characters.
dhcp smart-relay enable
Enables DHCP smart relay.
dhcp smart-relay exlude-vlan <1-4094>
Sets the DHCP smart relay to exlude the
specified VLAN.
dhcp smart-relay helper-address <ipaddress>
Sets the IP address of the DHCP server.
ip-address: Enter the IP address of the
remote server.
dhcp smart-relay option
Allows the device to add DHCP relay agent
information.
dhcp snooping enable
Enables DHCP snooping.
dhcp snooping vlan <1-4094>
Sets the DHCP snooping VLAN ID.
dhcp snooping vlan-mode <all|fixed>
Sets the DHCP snooping VLAN mode.
all: Enter this to have the device enable DHCP
snooping on all VLANs dynamically.
fixed: Enter this to specify which VLANS can
be enabled with DHCP snooping.
dhcp snooping option
MES-2110 Users Guide
Allows the device to add the DHCP option.
187
Chapter 23 Command Line Interface
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
dot1x enable
Enables 802.1x on the device.
dot1x reauth-max <1~10>
Sets the maximum number of times reauthentication can be used (1~10). The default
is 2 times. This kind of authentication method is
port-based.
dot1x guest-vlan <1-4094>
Sets the VLAN ID of the guest VLAN. This must
be an existing VLAN.
dot1x radius-server server-ip <ip-address>
Sets the RADIUS servers IP address.
dot1x radius-server shared-secret <string>
Sets the password for RADIUS server access.
string: Enter a maximum of 29 characters.
dot1x radius-server server-udp-port <165535>
Sets the UDP port number of the RADIUS server.
The default is 1812.
dot1x radius-server accounting-port <165535>
Sets the accounting port of the RADIUS server.
The default is 1813.
dot1x radius-server timeout <1-300>
Sets the timeout period of the RADIUS server.
The default is 30.
email-alarm disable
Disables the email alarm. This is the default.
email-alarm enable
Enables the email alarm.
email-alarm from <string|cr>
Sets the email alarms from field to the
specified string.
string: Enter up to 63 characters.
cr: Leave this blank and press the [Enter] key
to clear the email-alarm from setting.
email-alarm server <ip-address>
Sets the email alarms server to the specified IP
address.
email-alarm to [<id> <string>
<enable|disable>] | [<id>]
Sets the email alarms to field.
id: Enter an ID number for this recipent (1~5).
If you enter just the ID and no other paramters
(string or enable|disable), then this
setting is cleared for that ID.
string: Enter the recipients email address.
enable|disable: Select whether to enable
this recipient or disable it. When disabled, no
alarm emails are sent to that recipient.
email-alarm type
<coldstart|warmstart|rj45up|rj45down|gigeu
p|gigedown|confchange|newroot1d|topochange
1d|arpinspectionover> <enable|disable>
Sets the email alarm type. When one of these
events occurs and you have enabled that email
alarm type, the device sends out an alarm
email. You must configure each event
individually.
For example: email-alarm type coldstart
enable. This enables it for the coldstart event.
If you want to also enable it for the warmstart
event, you must configure it separately:
email-alarm type warmstart enable.
188
MES-2110 Users Guide
Chapter 23 Command Line Interface
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
erase-mac-table
Erases all dynamic MAC entries from the MAC
table.
frame-size <1522|1632>
Sets the frame size. The default is 1632.
gateway <ip-address>
Sets the gateway IP address.
hdos ip <index> <ip-address>
Sets the acceptable IP address for Host Denial
of Service (DoS) protection.
index: Enter an index number (1-5).
ip-address: Enter an IP address to associate
with an index number.
hdos ip-enable <index> <enable|disable>
Enables or disables an individual IP address for
Host Denial of Service (DoS) protection.
index: Enter an index number (1-5).
enable|disable: Enable or disable the IP
address associated with this index number.
hdos protection <enable|disable>
Enables or disables the Host Denial of Service
(DoS) protection service.
igmp immediate-leave <port-list>
Sets the port list for IGMP immediate-leave.
igmp query-mode <auto|disable>
Sets the IGMP query mode.
igmp snooping
Enables IGMP snooping.
igmp static <port-list>
Sets the IGMP static port list.
igmp vlan <1-4094>
Specifies the VLANs on which to perform IGMP
snooping if the mode is fixed.
igmp vlan-mode <auto|fixed>
Specifies how the VLANs snooped by the device
select IGMP packets.
auto: The device learns multicast group
membership on any VLAN. It drops a.ny IGMP
control messages on other VLANs after it
reaches this maximum number (auto mode).
fixed: The device only learns multicast group
membership on specified VLAN(s). It drops any
IGMP control messages for any unspecified
VLANs (fixed mode).
igmp vlan-query-mode <vlan-id>
<auto|disable>
Specifies the query mode for the specified VLAN.
ip <ip-address>
Sets the IP address of the device to the one
specified.
lacp group <group> <lacp|static>
Sets the specified trunk group to LACP or static.
lacp hash-mode <xor|lookup>
Sets the hash mode for trunk load balancing
selection.
xor: Select this XOR the lower 3 bits of the DA
and SA frames together.
lookup: Select this to use the lookup table.
MES-2110 Users Guide
189
Chapter 23 Command Line Interface
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
lacp port <port> <active|passive>
Sets the LACP port state to active or passive.
lacp priority <0-65535>
Sets the system priority for LACP.
lacp restart
Stores the LACP configurations and then restarts
them.
lacp trunk <group number> member <port num>
<port num> <port num> ...
Sets the trunk control configuration.
logins
Modifies the login account.
This prompts you to enter the old username and
password; to create a new username and
password; then set the login accounts read/
writer permissions.
loop detection <enable|disable>
Enables or disables loop detection.
loop mac <mac-address>
Sets the loop detection test frame MAC address.
loop port <id> <enable|disable>
Enables or disables individual port loop
detection.
mac-aging-time <1-255>
Sets the MAC aging time configuration. The
default is 19 (which converts to 304 seconds).
To determine the number of seconds, multiply
the MAC aging time value you enter by 16.
mac-filter add-allow-mac <mac-address>
<port id> <priority> <overrideenable|override-disable>
Sets the static unicast MAC configuration.
mac-filter add-deny-mac <mac-address>
Adds a specified MAC address to the deny MAC
configuration.
mac-filter delete <mac-address>
Deletes a static unicast MAC configuration.
mac-limit <enable|disable>
Enables or disables MAC-limit configuration.
mirror mode <all|disable>
Sets the mirror mode.
mirror monitoring-port <port-id>
Sets the mirror monitoring port.
netmask <netmask>
Sets the netmask.
no arp inspection enable
Disables ARP inspection.
no arp inspection mac-filter <mac-address>
Deletes the specified MAC address from the ARP
inspection filter.
no arp inspection vlan <1-4094>
Disables ARP inspection on the specified VLAN.
no dhcp client
Disables the DHCP client.
no dhcp binding mac <mac-address>
Deletes the DHCP snooping static binding table
by MAC address.
no dhcp binding ip <ip-address>
Deletes the DHCP snooping static binding table
by IP address.
no dhcp binding port <port-id>
Deletes the DHCP snooping static binding table
by port.
no dhcp binding vid <vlan-id>
Deletes the DHCP snooping static binding table
by VLAN ID.
no dhcp smart-relay enable
Disables DHCP smart relay.
190
MES-2110 Users Guide
Chapter 23 Command Line Interface
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
no dhcp smart-relay option
Disables the DHCP smart relay option.
no dhcp smart-relay vlan <cr|range>
Sets the DHCP smart relay to exclude VLANs.
cr: Leave this field blank and press [Enter] to
use the default setting.
range: Specify a range of VLAN IDs.
no dhcp snooping enable
Disables DHCP snooping.
no dhcp smart-relay exlude-vlan <1-4094>
Sets the DHCP smart relay to include the
previously excluded specified VLAN.
no dhcp snooping option
Disables the DHCP snooping option.
no dhcp snooping vlan <1-4094>
Disables the specified DHCP snooping VLAN ID.
no dot1x global
Stops 802.1x running globally
no dot1x guest-vlan
Disables Guest VLAN.
no gateway
Sets the devices default gateway.
no igmp immediate-leave
Sets IGMP fast leave to its default value.
no igmp query-mode <vlan-id>
Sets IGMP query mode to its default type for the
specified VLAN ID.
no igmp snooping
Disables IGMP snooping.
no igmp static
Disables the IGMP static port.
no igmp vlan <1-4094>
Disables IGMP VLAN for the specified VLAN ID.
no ip
Sets the device to its default IP address.
Note: You cannot change the devices IP
address over Telnet.
no lacp
Disables LACP.
no logins
Resets the login password to NULL.
no mvr <1-4094>
Removes an MVR configuration from the
specified VLAN.
no netmask
Sets the default netmask.
no spanning-tree
Disables the spanning tree.
no trunk <group-id>
Disables the trunk group.
no vlan <2-4094>
Deletes the static VLAN entry.
no vlan-stacking
Disables VLAN stacking.
qinq-sp-tpid <tpid>
Sets the SP TPID. SP TPID is a standard
Ethernet type code identifying the frame and
indicating whether the frame carries IEEE
802.1Q tag information.
tpid: Enter the Server Provider Tag Protocol
Identifier. This can be a four-digit hexadecimal
number from 0000 to ffff. The default is 9100.
qos schedule all_high_before_low
Sets the QoS schedule to all high before low.
qos schedule weighted_round_robin
Sets the QoS to weighted round_robin.
MES-2110 Users Guide
191
Chapter 23 Command Line Interface
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
qos ip-dscp-pri-queue <0~63>
<low|normal|preferred|high>
Sets the QoS IP IP-DSCP Priority to queue
mapping. The default is low.
qos tag-pri-queue <0-7>
<low|normal|preferred|high>
Set the QoS tag priority to queue mapping.
rmon clear
Clears the RMON information for ports 1~10.
snmp contact <contact-name>
Sets the SNMP system contact name.
contact-name: Enter up to 80 characters.
snmp getcommunity <community-name>
Sets the SNMP GET community.
community-name: Enter up to 30 characters.
Note: Only for SNMP v2c or lower.
snmp location <location-name>
Sets the SNMP system location.
location-name: Enter up to 80 characters.
snmp setcommunity <community-name>
Sets the SNMP SET community.
community-name: Enter up to 30 characters.
Note: Only for SNMP v2c or lower.
snmp trapcommunity <index> <communitystring>
Sets the SNMP trap community.
index: Enter an index number (1~5).
community-string: Enter up to 30
characters.
snmp trapenable <index> <enable|disable>
Enables the SNMP trap.
index: Enter an index number (1~5).
snmp trapip <index> <ip-address>
Sets the IP addresses of up to 5 SNMP
managers to receive SNMP traps.
index: Enter an index number (1~5).
sntp <enable | disable>
Enables and disables SNTP support.
sntp-NTP-primary-server <ip address>
Set SNTP primary server's IP address.
sntp-NTP-secondary-server <ip address>
Set SNTP secondary server's IP address.
sntp poll_interval <value>
Sets the interval in specified hours between
SNTP requests.
sntp time <yyyy:mo:dd:hh:mm:ss>
Sets the local time by year (yyyy), month (mm),
day (dd), hour (hh), minutes (mm), and
seconds (ss).
sntp timezone <+hh.mm | -hh.mm>
Sets the timezone offset.
+hh.mm: Increases the timezone offset by the
specified hours (hh) and minutes (mm).
-hh.mm: Increases the timezone offset by the
specified hours (hh) and minutes (mm).
192
MES-2110 Users Guide
Chapter 23 Command Line Interface
Table 80 Configuration Mode Commands
COMMAND
DESCRIPTION
sntp daylightsavingstart <mo.dd>
Sets the daylight savings time start date for the
specified month (mo) and day (dd).
sntp daylightsavingend <mo.dd>
Sets the daylight savings time end date for the
specified month (mo) and day (dd).
sntp daylightsaving <enable | disable>
Enables or disables daylight savings time.
spanning-tree enable
Enables RSTP.
spanning-tree forward-delay <4-30>
Sets the RSTP forward delay. The default is 15.
spanning-tree hello-time <1-10>
Sets the RSTP hello time. The default is 2.
spanning-tree maximum-age <6-40>
Sets the RSTP maximum age. The default is 20.
spanning-tree priority <0-61440>
Sets the RSTP switch priority the default is
32768.
syslog enable
Enables syslog support.
syslog disable
Disables syslog support.
syslog clear
Clears all data out of the syslog.
system-name <string>
Sets the system name to the specified string.
string: Enter up to 30 characters.
vlan-stacking
Enables VLAN stacking on the device.
vlan-type <802.1q | port-base>
Configures VLAN type.
23.7.1 IGMP Snooping Example
This example enables IGMP snooping, then sets the query mode to Auto and
port #10 to static..
MES-2110(config)# igmp snooping
MES-2110(config)# igmp query-mode auto
MES-2110(config)# igmp static 10
MES-2110 Users Guide
193
Chapter 23 Command Line Interface
23.7.2 RADIUS Configuration Example
This example sets up one RADIUS server (172.16.10.10) and a shared secret key
(hello) for authentication.
MES-2110# configure terminal
MES-2110(config)# vlan 99
MES-2110(config-vlan)# exit
MES-2110(config)# dot1x enable
MES-2110(config)# dot1x radius-server server-ip 172.16.10.10
MES-2110(config)# dot1x radius-server shared-secret hello
MES-2110(config)# dot1x guest-vlan 99
MES-2110(config)# exit
MES-2110(config)# interface port-channel 1
MES-2110(config-interface)# dot1x guest-vlan enable
MES-2110(config-interface)# end
MES-2110# show dot1x radius-server
Server IP Address : 172.16.10.10
Shared Key : hello
Sever Port Number : 1812
Accounting Port Number: 1813
Sever Time-out(sec) : 30
MES-2110# show dot1x global
802.1x protocol: Enabled
reauth-max: 2
Guest VLAN VID: 99
MES-2110# show dot1x port-control
802.1x Port-control Parameters
Guest VLAN VID:99
Port Active Reauthentication ReauthPeriod GuestVlan
1
No
Off
3600 (sec)
Yes
2
No
Off
3600 (sec)
No
3
No
Off
3600 (sec)
No
4
No
Off
3600 (sec)
No
5
No
Off
3600 (sec)
No
6
No
Off
3600 (sec)
No
7
No
Off
3600 (sec)
No
8
No
Off
3600 (sec)
No
9
No
Off
3600 (sec)
No
10
No
Off
3600 (sec)
No
194
MES-2110 Users Guide
Chapter 23 Command Line Interface
23.8 MVR Mode
This is an ancillary mode of Configuration mode. You must be in Configuration
mode for these commands to work.
When in MVR-Configuration mode, the command prompt is as follows:.
MES-2110(config-mvr)#
The following is a list of available MVR-Configuration mode commands:
Note: These commands only apply to the MVR ID specified when you enter MVRConfiguration mode.
Table 81 MVR-Configuration Mode Commands
COMMAND
DESCRIPTION
mvr <1-4094>
Enters MVR (multicast VLAN relay) configuration
mode for the specified MVR, creating the MVR if
necessary.
Note: You must be in Configuration mode for
this command to work.
group <group-id> <start-address> <n>
Sets the multicast group range for the current
MVR group.
group-id: Enter 1-255 characters for the group
identification.
start-address: Enter the start IP address for
the multicast range of this group.
n: Enter the number of additional addresses to
generate based on the start address for the
multicast range of this group.
inactive
Disables the MVR settings for the current MVR
group.
no inactive
Enables the no settings for the current MVR
group.
no receiver-port <port-list>
Disables the receiver port(s) for the current MVR
group.
no source-port <port-list>
Disables the source port(s) for the current MVR
group.
no tagged <port-list>
Sets the untag port numbers for the current MVR
group.
no group <cr|group-id>
Removes all or specified MVR group settings for
the current MVR group.
cr: Leave this field blank and press [Enter].
group-id: Enter the group ID to remove.
MES-2110 Users Guide
195
Chapter 23 Command Line Interface
Table 81 MVR-Configuration Mode Commands
COMMAND
DESCRIPTION
mode <dynamic|compatible>
Sets the MVR mode to dynamic or compatible for
the current MVR group.
name <name>
Sets the current MVR group name for
identification purposes.
name: Enter 1-30 characters.
query-mode <auto|disable>
Sets the query mode of the current MVR group.
receiver-port <port-list>
Sets the receiver port(s) for the current MVR
group. An MVR receiver port can only receive
multicast traffic in a multicast VLAN.
source-port <port-list>
Sets the source port(s) for the current MVR
group. An MVR source port can send and receive
multicast traffic in a multicast VLAN.
tagged <port-list>
Sets the port(s) to VLAN tags for the current
MVR group.
23.8.1 MVR Command Example
This example configures MVR in the following ways:
1
Enters MVR mode. This creates a multicast VLAN with the name StreamVlan and
the multicast VLAN ID of 100.
Specifies source port 9 for the multicast group.
Specifies receiver ports 1-4 and 10 for the multicast group.
Specifies dynamic mode for the multicast group.
Sets the ports 9 and 10 to tag VLAN IDs.
Configures MVR multicast group addresses 227.3.3.1 through 227.3.3.10 for
multicast group ID 1.
MES-2110(config)# mvr
MES-2110(config-mvr)#
MES-2110(config-mvr)#
MES-2110(config-mvr)#
MES-2110(config-mvr)#
MES-2110(config-mvr)#
MES-2110(config-mvr)#
MES-2110(config-mvr)#
196
100
no inactive
name StreamVlan
mode dynamic
receiver-port 1,2,3,4,10
source-port 9
tagged 9,10
group 1 227.3.3.1 10
MES-2110 Users Guide
Chapter 23 Command Line Interface
23.9 VLAN Mode
This is an ancillary mode of Configuration mode. You must be in Configuration
mode for these commands to work.
When in VLAN-Configuration mode, the command prompt is as follows:.
MES-2110(config-vlan)#
The following is a list of available VLAN-Configuration mode commands:
Note: These commands only apply to the VLAN ID specified when you enter VLAN
Configuration mode.
Table 82 VLAN Mode Commands
COMMAND
DESCRIPTION
vlan <1-4094>
Enters VLAN Configuration mode for the
specified VLAN ID. If no VLAN IDs exist, then
this creates the specified ID.
manage
Sets the current VLAN as a management VLAN.
member <port-list>
Specifies the ports that are members of the
current VLAN group.
non-member <port-list>
Specifies the ports that are excluded from the
current VLAN group.
tagging <port-list>
Specifies the ports in the current VLAN group for
which you want outgoing frames tagged.
untagging <port-list>
Specifies the ports in the current VLAN group for
which you do not want outgoing frames tagged.
use-vid-priority <yes|no>
Select yes to enable VID priority for the current
VLAN group, or no to disable it.
vid-priority <0~7>
Sets the VID priority (0~7).
MES-2110 Users Guide
197
Chapter 23 Command Line Interface
23.9.1 VLAN ID Priority Example
This example assigns port 1 as a tagged port for VLAN 1 and sets the priority of all
incoming packets from VLAN 1 to priority 3.
MES-2110> enable
MES-2110# configure terminal
MES-2110(config)# vlan 1
MES-2110(config-vlan)# tagging 1
MES-2110(config-vlan)# vid-priority 3
MES-2110(config-vlan)# use-vid-priority yes
MES-2110(config-vlan)# exit
MES-2110(config)# interface port-channel 1
MES-2110(config-interface)# vid-pri-override enable
MES-2110(config-interface)# exit
MES-2110(config)# exit
MES-2110# show priority-override
port
vid-pri-override
da-pri-override
sa-pri-override
=================================================================
01
enabled
disabled
disabled
02
disabled
disabled
disabled
03
disabled
disabled
disabled
04
disabled
disabled
disabled
05
disabled
disabled
disabled
06
disabled
disabled
disabled
07
disabled
disabled
disabled
08
disabled
disabled
disabled
09
disabled
disabled
disabled
10
disabled
disabled
disabled
MES-2110# show vlan tag-base vlan-table
1 (M:member, U:untag)
No.
VLAN-ID
Priority
Pri-override
1234567890 (T:tag, -:nomember)
=========================================================
1
1
3
Yes
TUUUUUUUUU
2
24
0
No
---------MES-2110#
23.10 Interface Mode
This is an ancillary mode of Configuration mode. You must be in Configuration
mode for these commands to work.
When in Interface-Configuration mode, the command prompt is as follows:.
MES-2110(config-interface)#
198
MES-2110 Users Guide
Chapter 23 Command Line Interface
Note: These commands only apply to the ports specified when you enter Interface
Configuration mode.
Table 83 Interface Mode Commands
COMMAND
DESCRIPTION
interface port-channel <port-list>
Enters Interface Configuration mode for the
specified port(s).
abnormal-detection-enable
Enables port detection for the current port(s).
active
Enables the current port(s).
arp-inspection-trust
Enables ARP inspection trust for the current
port(s). When enabled, the device does not
discard ARP packets on trusted ports.
auto-negotiation
Enables auto-negotiation for the current port(s).
bandwidth-limit egress <cr>|
<low|medium|high> <rate>
Sets the egress rate for the current port(s).
cr: Press [ENTER] without entering any other
parameters to enable egress bandwidth control
on the current port(s).
low: 64K~960K (64..960) in 64k steps.
medium: 1~100M (1..100) in 1M steps.
high: 100~1000M (110..1000) in 10M steps.
bandwidth-limit ingress <low|medium|high>
<rate>
Sets the ingress rate for the current port(s).
cr: Press [ENTER] without entering any other
parameters to enable egress bandwidth control
on the current port(s).
low: 64K~960K (64..960) in 64k steps.
medium: 1~100M (1..100) in 1M steps.
high: 100~1000M (110..1000) in 10M steps.
bpdu-mode <on|off|tunnel>
Sets the BPDU packet process mode for the
current port(s).
da-pri-override <enable|disable>
Sets the destination MAC priority override for the
current port(s).
dhcp snooping trust
Sets DHCP snooping trust for the current port(s).
Trusted ports are connected to DHCP servers or
other switches, and the device discards DHCP
packets from trusted ports only if the rate at
which DHCP packets arrive is too high.
egress-set <port-list>
Sets the outgoing traffic port list for a port-base
VLAN for the current port(s).
flow-control
Enables interface flow control for the current
port(s).
MES-2110 Users Guide
199
Chapter 23 Command Line Interface
Table 83 Interface Mode Commands
COMMAND
DESCRIPTION
frame-type <fallback|check|secure>
Sets the port frame type for the current port(s).
You can choose to accept both non-member and
untagged incoming frames (fallback), just
untagged incoming frames (check) or drop all
non-member and untagged incoming frames on
a port (secure).
fallback: Accepts incoming frames
(nonmember forward/untag forward).
check: Accepts incoming frames (nonmember
drop/untag forward).
secure: Accepts incoming frames (nonmember
drop/untag drop).
isolate
Isolates the specified prots. Isolated ports
belonging to the same VLAN do not
communicate with each other.
lock-mac
Locks the MAC configuration for the current
port(s).
mac-limit action <enable|disable>
Enables or disables the MAC limit for the current
port(s).
mac-limit quantity <1-20>
Sets the MAC limit quantity for the current
port(s).
mirror
Enables port mirroring for the current port(s).
name <string>
Sets a name for the port for the current port(s).
string: Enter up to 15 characters.
no abnormal
Disables individual port detection for the current
port(s).
no active
Disables the current port(s).
no arp-inspection-trust
Disables ARP inspection trust for the current
port(s).
no bandwidth-limit egress
Disables egress rate for the current port(s).
no bandwidth-limit ingress
Disables ingress rate for the current port(s).
no dhcp snooping trust
Disables DHCP snooping trust for the current
port(s).
no flow-control
Disables flow control on the interface for the
current port(s).
no auto-negotiation
Disables auto-negotiation. for the current
port(s).
no isolate
Disables port isolation for the current port(s).
no lock-mac
Disables MAC locking for the port for the current
port(s).
no mirror
Disables port mirroring for the current port(s).
no broadcast-limit
Disables the broadcast packet limit for the
current port(s).
200
MES-2110 Users Guide
Chapter 23 Command Line Interface
Table 83 Interface Mode Commands
COMMAND
DESCRIPTION
no multicast-limit
Disables the multicast packet limit for the
current port(s).
no dlf-limit
Disables the DLF packet limit for the current
port(s).
no dot1x port-control
Disables port control of 802.1x for the current
port(s).
no dot1x guest-vlan
Disables guest VLAN for the current port(s).
no dot1x reauth
Disables reauthentication of 802.1x for the
current port(s).
8021p-priority <0-7>
Sets default ingress priority to use when no
priority information avilable for the current
port(s).
pvid <1-4094>
Sets the PVID for the current port(s).
qos-priority-mode <default|tag|ip|ip&tag>
Sets the QoS priority mode for the current
port(s).
default: Port Priority.
tag: IEEE Tagged Frame Priority.
ip: IPv4 and IPv6 Frame Priority.
ip&tag: IPv4 and IPv6 with IEEE Tagged Frame
Priority.
qos-ipdscp-over-tag <enable|disable>
Sets the QoS ipdscp over tag priority for the
current port(s).
dot1x reauth-period <1-999999>
Set reauthentication period for the current
port(s). The default is 3600.
dot1x enable
Enable 802.1x port control for the current
port(s).
dot1x reauth enable
Enable 802.1x reauthentication for the current
port(s).
dot1x guest-vlan enable
Enables guest VLAN for the current port(s).
rstp-edge <on|off>
Sets the RSTP port edge for the current port(s).
rstp-p2p <auto|on|off>
Sets the RSTP port point-to-point (p2p) option
for the current port(s).
rstp-path-cost <0-65535>
Sets the RSTP port path cost for the current
port(s). The default is 1000M=4, 100M=19.
rstp-priority <0-255>
Sets the RSTP port priority for the current
port(s). The default is 128.
sa-pri-override <enable|disable>
Sets the source MAC priority override for the
current port(s).
speed-duplex <10f|10h|100f|100h|1000f>
Sets the duplex and speed mode for the current
port(s).
sfp-speed <100|1000|1000-no-auto>
Sets the SFP fiber speed for the current port(s).
MES-2110 Users Guide
201
Chapter 23 Command Line Interface
Table 83 Interface Mode Commands
COMMAND
DESCRIPTION
storm-control broadcast-limit [cr |
<low|medium|high> <rate>]
Sets the broadcast storm control for the current
port(s).
cr: Enter nothing for this field and just press
[Enter] to enable broadcast packet limits on the
current port(s).
low: 64K~960K (64..960) in 64k steps.
medium: 1~100M (1..100) in 1M steps.
high: 100~1000M (110..1000) in 10M steps.
storm-control multicast-limit [cr |
<low|medium|high> <rate>]
Sets the multicast storm control for the current
port(s).
cr: Enter nothing for this field and just press
[Enter] to enable multicast packet limits on the
current port(s).
low: 64K~960K (64..960) in 64k steps.
medium: 1~100M (1..100) in 1M steps.
high: 100~1000M (110..1000) in 10M steps.
storm-control dlf [cr |<low|medium|high>
<rate>]
Sets the DLF storm control for the current
port(s).
cr: Enter nothing for this field and just press
[Enter] to enable DLF packet limits on the
current port(s).
low: 64K~960K (64..960) in 64k steps.
medium: 1~100M (1..100) in 1M steps.
high: 100~1000M (110..1000) in 10M steps.
vid-pri-overide <enable|disable>
Enables or disables the VLAN ID priority override
for the current port(s).
vlan-stacking role <normal|access|tunnel>
Sets the VLAN stacking port roles of the current
port(s.)
normal: The device ignores frames received (or
transmitted) on this port with VLAN stacking
tags.
access: The device adds the SP TPID tag to all
incoming frames received on this port.
tunnel: Use this for egress ports at the edge of
the service provider's network.
Note: In order to support VLAN stacking on a
port, the port must allow frames of 1526
bytes (1522 bytes + 4 bytes for the
second tag) to pass through it.
202
MES-2110 Users Guide
Chapter 23 Command Line Interface
Table 83 Interface Mode Commands
COMMAND
DESCRIPTION
vlan-stacking SPVID <1-4094>
Sets the service provider VLAN ID of the current
port(s).
vlan-stacking priority <0-7>
Sets the priority (0-7) of the current port(s) in
VLAN stacking.
23.10.1 Untrusted ARP Inspection Example
This example assigns port 1 to 8 as untrusted for ARP inspection, and displays
whether the devices ports have a trusted or untrusted status. Generally if you
want to enable ARP inspection on the device you also have to enable DHCP
snooping first to build a binding table.
MES-2110(config)# dhcp snooping enable
MES-2110(config)# dhcp snooping vlan-mode all
MES-2110(config)# arp inspection enable
MES-2110(config)# arp inspection vlan-mode all
MES-2110(config)# interface port-channel 1,2,3,4,5,6,7,8
MES-2110(config-interface)# no arp-inspection-trust
MES-2110# show arp inspection config
ARP Inspection is enabled
ARP Inspection MAC-Filter-Aging-Time : 5(min)
ARP Inspection VLAN Mode : All VLAN
ARP Inspection VLAN :
Port
ARP-Inspection
-------------------------01
untrust
02
untrust
03
untrust
04
untrust
05
untrust
06
untrust
07
untrust
08
untrust
09
trust
10
trust
23.10.2 Outgoing Traffic Bandwidth Limit Example
This example sets the outgoing traffic bandwidth limit to 1 Mbps for port 2.
MES-2110# configure terminal
MES-2110(config)# interface port-channel 2
MES-2110(config-interface)# bandwidth-limit egress medium 1
MES-2110(config-interface)# bandwidth-limit egress
MES-2110 Users Guide
203
Chapter 23 Command Line Interface
23.10.3 Frame Tagging Examples
In the following example, both A and B are Service Providers Network (SPN)
customers with VPN tunnels between their head offices and branch offices
respectively. Both have an identical VLAN tag for their VLAN group. The service
provider can separate these two VLANs within its network by adding tag 37 to
distinguish customer A and tag 48 to distinguish customer B at edge device x and
then stripping those tags at edge device y as the data frames leave the network.
Figure 93 Frame Tagging Example
This example shows how to configure ports 1 and 2 on the switch to tag incoming
frames with the service providers VID of 37 (ports are connected to customer A
network). This example also shows how to set the priority for ports 1 and 2 to 3.
MES-2110(config)# vlan-stacking
MES-2110(config)# interface port-channel 1,2
MES-2110(config-interface)# vlan-stacking role access
MES-2110(config-interface)# vlan-stacking spvid 37
MES-2110(config-interface)# vlan-stacking priority 3
MES-2110(config-interface)# exit
MES-2110(config)# exit
MES-2110# show vlan stacking
VLAN Stacking:Enabled
SP TPID:0x9100
Port
Role
SPVID
Priority
-----------------------------------------1
Access
37
3
2
Access
37
3
3
Normal
1
0
4
Normal
1
0
5
Normal
1
0
6
Normal
1
0
7
Normal
1
0
8
Normal
1
0
9
Normal
1
0
10
Normal
1
0
204
MES-2110 Users Guide
Chapter 23 Command Line Interface
This example applies only to switches that support the SVLAN feature. It shows
how to configure both port 1 (connected to customer A) and port 2 (connected to
customer B) as the ingress ports (access ports) and port 10 as the egress port
(tunnel port) on the switch (edge device x of the service providers network).
Incoming frames received on port 1 and 2 are tagged with the ingress ports SP
VID 37 and 48 respectively before the switch forwards them to port 10.
The ingress ports (port 1 and 2) and the egress port (port 10) should be in the
same static VLAN (customer VLAN) to communicate with each other. This example
also shows how to configure service providers VLANs 37 and 48 in the switchs
SVLAN table. The switch checks the incoming frames received on the tunnel port
(port 10) and drops the frames whose SPVID is not in the SVLAN table.
MES-2110# configure terminal
MES-2110(config)# interface port-channel 1
MES-2110(config-interface)# vlan-stacking role access
MES-2110(config-interface)# vlan-stacking SPVID 37
MES-2110(config-interface)# exit
MES-2110(config)# interface port-channel 2
MES-2110(config-interface)# vlan-stacking role access
MES-2110(config-interface)# vlan-stacking SPVID 48
MES-2110(config-interface)# exit
MES-2110(config)# interface port-channel 10
MES-2110(config-interface)# vlan-stacking role tunnel
MES-2110(config-interface)# exit
MES-2110(config)# vlan 24
MES-2110(config-vlan)# tagging 10
MES-2110(config-vlan)# untagging 1,2
MES-2110(config-vlan)# exit
MES-2110(config)# interface port-channel 1,2,8
MES-2110(config-interface)# frame-type fallback
MES-2110(config)# exit
MES-2110# show vlan stacking
VLAN Stacking:Enabled
SP TPID:0x9100
Port
Role
SPVID
Priority
-----------------------------------------1
Access
37
0
2
Access
48
0
3
Normal
1
0
4
Normal
1
0
5
Normal
1
0
6
Normal
1
0
7
Normal
1
0
8
Normal
1
0
9
Normal
1
0
10
Tunnel
1
0
MES-2110 Users Guide
205
Chapter 23 Command Line Interface
206
MES-2110 Users Guide
CHAPTER
24
Troubleshooting
This chapter offers some suggestions to solve problems you might encounter. The
potential problems are divided into the following categories.
Power, Hardware Connections, and LEDs
MES-2110 Access and Login
MES-2110 Configuration and Console
24.1 Power, Hardware Connections, and LEDs
The MES-2110 does not turn on. None of the LEDs turn on.
Make sure you are using the power adaptor or cord included with the MES-2110.
Make sure the power adaptor or cord is connected to the MES-2110 and plugged
in to an appropriate power source. Make sure the power source is turned on.
Disconnect and re-connect the power adaptor or cord to the MES-2110.
If the problem continues, contact the vendor.
The ALM LED is on.
Disconnect and re-connect the power adaptor or cord to the MES-2110.
If the problem continues, contact the vendor.
MES-2110 Users Guide
207
Chapter 24 Troubleshooting
One of the LEDs does not behave as expected.
Make sure you understand the normal behavior of the LED. See Section 3.4 on
page 35.
Check the hardware connections. See Section 24.1 on page 207.
Inspect your cables for damage. Contact the vendor to replace any damaged
cables.
Disconnect and re-connect the power adaptor or cord to the MES-2110.
If the problem continues, contact the vendor.
24.2 MES-2110 Access and Login
I forgot the IP address for the MES-2110.
The default IP address is 192.168.1.1.
Use the console port to log in to the MES-2110.
If this does not work, you have to reset the device to its factory defaults. See
Section 5.6 on page 59.
I forgot the username and/or password.
208
The default username is admin and the default password is 1234.
If this does not work, you have to reset the device to its factory defaults. See
Section 5.6 on page 59.
MES-2110 Users Guide
Chapter 24 Troubleshooting
I cannot see or access the Login screen in the Web Configurator.
Make sure you are using the correct IP address.
The default IP address is 192.168.1.1.
If you changed the IP address, use the new IP address.
If you changed the IP address and have forgotten it, see the troubleshooting
suggestions for I forgot the IP address for the MES-2110.
Check the hardware connections, and make sure the LEDs are behaving as
expected. See Section 3.4 on page 35.
Make sure your Internet browser does not block pop-up windows and has
JavaScripts and Java enabled.
Make sure your computer is in the same subnet as the MES-2110. (If you know
that there are routers between your computer and the MES-2110, skip this step.)
Reset the device to its factory defaults, and try to access the MES-2110 with the
default IP address. See Section 5.6 on page 59.
If the problem continues, contact the vendor, or try one of the advanced
suggestions.
Advanced Suggestions
Try to access the MES-2110 using another service, such as Telnet or over the
console port. If you can access the MES-2110, check the remote management
settings to find out why the MES-2110 does not respond to HTTP.
Some possible reasons for being unable to connect over the in-band management
ports are that you:
Deleted the management VLAN (default is VLAN 1).
Deleted all port-based VLANs with the CPU port as a member. The CPU port is
the management port of the MES-2110.
Filtered all traffic to the CPU port.
Disabled all ports.
Misconfigured the text configuration file.
Prevented all services from accessing the MES-2110.
MES-2110 Users Guide
209
Chapter 24 Troubleshooting
Changed a service port number but forget it.
See Chapter 23 on page 179 for details on managing the MES-2110 through the
console port. This will allow you to correct any mistakes you may have made in
the Web Configurator.
I can see the Login screen, but I cannot log in to the MES-2110.
Make sure you have entered the user name and password correctly. The default
user name is admin, and the default password is 1234. These fields are casesensitive, so make sure [Caps Lock] is not on.
You may have exceeded the maximum number of concurrent Telnet sessions.
Close other Telnet session(s) or try connecting again later.
Check that you have enabled logins for HTTP or Telnet. If you have configured a
secured client IP address, your computers IP address must match it. Refer to the
chapter on access control for details.
Disconnect and re-connect the cord to the MES-2110.
If this does not work, you have to reset the device to its factory defaults. See
Section 5.6 on page 59.
Pop-up Windows, JavaScript and Java Permissions
In order to use the web configurator you need to allow:
Web browser pop-up windows from your device.
JavaScripts (enabled by default).
Java permissions (enabled by default).
210
MES-2110 Users Guide
Chapter 24 Troubleshooting
24.3 MES-2110 Configuration and Console
Im trying to configure MVR but I get an error message.
MVR only functions with Tag-Based (802.1q) VLANs. To rectify this:
Open the Configuration > VLAN Menu > VLAN Type screen and set the
VLAN Type option to Tag-Based (802.1q).
Or
Connect to the MES-2110 through the console port (Chapter 23 on page 179)
and enter the following commands:.
MES-2110: enable
MES-2110# configure terminal
MES-2110(config)# vlan-type 802.1q
I applied changes in the Web Configurator but they are not taking effect.
Makes sure that you saved all configuration changes using the Save Settings
link in the Web Configurators navigation pane.
Clean out the cache of the browser that you are using to connect to the MES2110s Web Configurator, and make sure that youre only using a browser
supported by the device (Chapter 1 on page 19)
Try making your changes through the MES-2110s command line interface
(Chapter 23 on page 179), and using the write memory command to make the
changes permanent.
Power off the MES-2110, then power it back on and make your changes afresh.
Reset the MES-2110 to its factory default settings (Section 5.6 on page 59).
If the problem continues, contact the vendor.
MES-2110 Users Guide
211
Chapter 24 Troubleshooting
I cannot connect to the Web Configurator over the console port.
Ensure that your console settings are configured with the following settings:
SETTING
DEFAULT VALUE
Terminal Emulation
VT100
Baud Rate
9600
Parity
None
Number of Data Bits
Number of Stop Bits
Flow Control
None
I keep getting Invalid command messages when trying to configure the MES2110 over the console port.
There are a number of different modes in the MES-2110 command line
interface. In order to use certain commands, you must be in the appropriate
mode. See Chapter 23 on page 179 for information on the different modes, how
they work, and which commands you may use in them.
To see which commands are available to you while using the command line
interface, type ? and press [ENTER].
I enabled ARP inspection on my MES-2110 but it doesnt seem to be working.
It is recommended you enable DHCP snooping at least one day before you enable
ARP inspection so that the MES-2110 has enough time to build the binding table.
My changes in the Web Configurator keep getting overwritten.
The MES-2110 allows up to five different accounts to access its Web Configurator.
Make sure that you and another user are not modifying the device at the same
time. Any changes you make will be overwritten when the other user saves his or
her changes, and vice versa.
212
MES-2110 Users Guide
Chapter 24 Troubleshooting
Every time I try to change the MES-2110s IP address over Telnet, I get an error.
You cannot change the devices IP address over Telnet.
MES-2110 Users Guide
213
Chapter 24 Troubleshooting
214
MES-2110 Users Guide
CHAPTER
25
Product Specifications
The following tables summarize the MES-2110s hardware and firmware features.
Table 84 Hardware Specifications
SPECIFICATION
DESCRIPTION
Dimensions
268 mm (W) x 128 mm (D) x 44 mm (H)
Weight
1.2 kg
Power Specification
AC: 110-240V AC, 50/60 Hz, 14 W Max.
DC: -36V~-56V DC, 14 W Max.
Interfaces
8 10/100 Base-Tx ports
2 GbE Dual Personality interfaces (Each interface has one
1000Base-T RJ-45 port and one Small Form-Factor Pluggable
(SFP) slot, with one port active at a time.)
2 mini-GBIC (SFP) slots
Auto-negotiation
Auto-MDIX
One console port
Compliant with IEEE 802.3/3u
Back pressure flow control for half duplex
Flow control for full duplex (IEEE 802.3x)
LEDs
Per switch: PWR, SYS
Per Fast Ethernet RJ-45 10/100 port: LNK/ACT
Per mini-GBIC slot: LNK, ACT
Per mini-GBIC slot (in dual personality interface): LNK/ACT
Operating
Environment
Temperature: 0 C ~ 50 C
Storage Environment
Temperature: -40 C ~ 70 C
Humidity: 10 ~ 95% (non-condensing)
Humidity: 10 ~ 95% (non-condensing)
MES-2110 Users Guide
215
Chapter 25 Product Specifications
Table 85 Firmware Specifications
FEATURE
DESCRIPTION
Default IP Address
192.168.1.1
Default Subnet Mask
255.255.255.0 (24 bits)
Administrator User
Name
admin
Default Password
1234
Number of Login
Accounts Configurable
on the Switch
5 accounts configured on the MES-2110.
VLAN
A VLAN (Virtual Local Area Network) allows a physical network
to be partitioned into multiple logical networks. Devices on a
logical network belong to one group. A device can belong to
more than one group. With VLAN, a device cannot directly talk
to or hear from devices that are not in the same group(s); the
traffic must first go through a router.
VLAN Stacking
Use VLAN stacking to add an outer VLAN tag to the inner IEEE
802.1Q tagged frames that enter the network. By tagging the
tagged frames (double-tagged frames), the service provider
can manage up to 4,094 VLAN groups with each group
containing up to 4,094 customer VLANs. This allows a service
provider to provide different service, based on specific VLANs,
for many different customers.
MAC Address Filter
Filter traffic based on the source and/or destination MAC
address.
IGMP Snooping
The MES-2110 supports IGMP snooping, enabling group
multicast traffic to be only forwarded to ports that are
members of that group; thus allowing you to significantly
reduce multicast traffic passing through your MES-2110.
QoS
Queuing is used to help solve performance degradation when
there is network congestion. The following scheduling services
are supported: weighted round robin and all high before low
queuing. This allows the MES-2110 to maintain separate
queues for frames from each individual source or flow and
prevent a source from monopolizing the bandwidth.
Bandwidth Control
Bandwidth control means defining a maximum allowable
bandwidth for incoming and/or out-going traffic flows on a port.
Broadcast Storm Control The device supports per port TCP/IP ingress rate limiting along
with independent storm prevention.
Port Mirroring
216
Port mirroring allows you to copy traffic going from one or all
ports to another or all ports in order that you can examine the
traffic from the mirror port (the port you copy the traffic to)
without interference.
MES-2110 Users Guide
Chapter 25 Product Specifications
Table 85 Firmware Specifications
FEATURE
DESCRIPTION
Multicast VLAN
Registration (MVR)
Multicast VLAN Registration (MVR) is designed for applications
(such as Media-on-Demand (MoD)) using multicast traffic
across a network. MVR allows one single multicast VLAN to be
shared among different subscriber VLANs on the network.
This improves bandwidth utilization by reducing multicast
traffic in the subscriber VLANs and simplifies multicast group
management.
L2 Multicast
The device supports Layer-2 multicast switching with line-rate
(wire speed) switching for all packet sizes and conditions. In
addition, the MES-2110 can send packets to Ethernet devices
that are not VLAN-aware by untagging (removing the VLAN
tags) IP multicast packets.
STP (Spanning Tree
Protocol)
STP detects and breaks network loops and provides backup
links between switches, bridges or routers. It allows a MES2110 to interact with other STP-compliant switches in your
network to ensure that only one path exists between any two
stations on the network.
Loop Detection
Use the loop detection feature to monitor any network loops on
the edge of your network.
IP Source Guard
Use IP source guard to filter unauthorized DHCP and ARP
packets in your network.
Link Aggregation
Link aggregation (trunking) is the grouping of physical ports
into one logical higher-capacity link. You may want to trunk
ports if for example, it is cheaper to use multiple lower-speed
links than to under-utilize a high-speed, but more costly,
single-port link.
Port Authentication and
Security
For security, the MES-2110 allows authentication using IEEE
802.1x with an external RADIUS server and port security that
allows only packets with dynamically learned MAC addresses
and/or configured static MAC addresses to pass through a port
on the MES-2110.
Authentication and
Accounting
The MES-2110 supports authentication and accounting services
via RADIUS.
Device Management
Use the web configurator or commands to easily configure the
rich range of features on the MES-2110.
Syslog
The MES-2110 can generate syslog messages for system
monitoring.
Firmware Upgrade
Download new firmware (when available) from the ZyXEL web
site and use the web configurator, CLI or TFTP tool to put it on
the MES-2110.
Note: Only upload firmware for your specific model!
Configuration Backup &
Restoration
MES-2110 Users Guide
Make a copy of the MES-2110s configuration and put it back on
the MES-2110 later if you decide you want to revert back to an
earlier configuration.
217
Chapter 25 Product Specifications
The following list, which is not exhaustive, illustrates the standards supported in
the MES-2110.
Table 86 Standards Supported
STANDARD
DESCRIPTION
RFC 826
Address Resolution Protocol (ARP)
RFC 894
Ethernet II Encapsulation
RFC 1112
IGMP v1
RFC 1157
SNMPv1: Simple Network Management Protocol version 1
RFC 1213
SNMP MIB II
RFC 1493
Bridge MIBs
RFC 1643
Ethernet MIBs
RFC 1757
RMON
RFC 1901
SNMPv2c Simple Network Management Protocol version 2c
RFC 2138
RADIUS (Remote Authentication Dial In User Service)
RFC 2139
RADIUS Accounting
RFC 2236
Internet Group Management Protocol, Version 2.
RFC 3046
DHCP Relay
RFC 4330
Simple Network Time Protocol(SNTP)
IEEE 802.1x
Port Based Network Access Control
IEEE 802.1D
MAC Bridges
IEEE 802.1p
Traffic Types - Packet Priority
IEEE 802.1Q
Tagged VLAN
IEEE 802.1w
Rapid Spanning Tree Protocol (RSTP)
IEEE 802.3
Packet Format
IEEE 802.3ad
Link Aggregation
IEEE 802.3x
Flow Control
Safety
UL 60950-1
CSA 60950-1
EN 60950-1
IEC 60950-1
EMC
FCC Part 15 (Class A)
CE EMC (Class A)
218
MES-2110 Users Guide
APPENDIX
Changing a Fuse
This appendix shows you how to remove and install fuses for the MES-2110.
If you use a fuse other than an included fuse, make sure it
matches the fuse specifications in the appendix on product
specifications.
Removing a Fuse
Disconnect all power from the MES-2110 before you begin this
procedure.
1
Remove the power cord from the MES-2110.
See the product specifications for the location of the fuse. Use a small flat-head
screwdriver to carefully pry out the fuse housing.
A burnt-out fuse is blackened, darkened or cloudy inside its glass casing. A
working fuse has a completely clear glass casing. Pull gently, but firmly, to remove
the burnt out fuse from the fuse housing. Dispose of the burnt-out fuse properly.
Installing a Fuse
1
The MES-2110 is shipped from the factory with one spare fuse included in a boxlike section of the fuse housing. Push the middle part of the box-like section to
access the spare fuse. Put another spare fuse in its place in order to always have
one on hand.
Push the replacement fuse into the fuse housing until you hear a click.
Push the fuse housing back into the MES-2110 until you hear a click.
Plug the power cord back into the unit.
MES-2110 Users Guide
219
Appendix A Changing a Fuse
220
MES-2110 Users Guide
APPENDIX
Common Services
The following table lists some commonly-used services and their associated
protocols and port numbers. For a comprehensive list of port numbers, ICMP type/
code numbers and services, visit the IANA (Internet Assigned Number Authority)
web site.
Name: This is a short, descriptive name for the service. You can use this one or
create a different one, if you like.
Protocol: This is the type of IP protocol used by the service. If this is TCP/
UDP, then the service uses the same port number with TCP and UDP. If this is
User-Defined, the Port(s) is the IP protocol number, not the port number.
Port(s): This value depends on the Protocol. Please refer to RFC 1700 for
further information about port numbers.
If the Protocol is TCP, UDP, or TCP/UDP, this is the IP port number.
If the Protocol is USER, this is the IP protocol number.
Description: This is a brief explanation of the applications that use this service
or the situations in which this service is used.
MES-2110 Users Guide
221
Appendix B Common Services
Table 87 Commonly Used Services
222
NAME
PROTOCOL
PORT(S)
DESCRIPTION
AH
(IPSEC_TUNNEL)
User-Defined
51
The IPSEC AH (Authentication Header)
tunneling protocol uses this service.
AIM/New-ICQ
TCP
5190
AOLs Internet Messenger service. It is
also used as a listening port by ICQ.
AUTH
TCP
113
Authentication protocol used by some
servers.
BGP
TCP
179
Border Gateway Protocol.
BOOTP_CLIENT
UDP
68
DHCP Client.
BOOTP_SERVER
UDP
67
DHCP Server.
CU-SEEME
TCP
7648
UDP
24032
A popular videoconferencing solution
from White Pines Software.
DNS
TCP/UDP
53
Domain Name Server, a service that
matches web names (for example
www.zyxel.com) to IP numbers.
ESP
(IPSEC_TUNNEL)
User-Defined
50
The IPSEC ESP (Encapsulation
Security Protocol) tunneling protocol
uses this service.
FINGER
TCP
79
Finger is a UNIX or Internet related
command that can be used to find out
if a user is logged on.
FTP
TCP
20
TCP
21
File Transfer Program, a program to
enable fast transfer of files, including
large files that may not be possible by
e-mail.
H.323
TCP
1720
NetMeeting uses this protocol.
HTTP
TCP
80
Hyper Text Transfer Protocol - a client/
server protocol for the world wide
web.
HTTPS
TCP
443
HTTPS is a secured http session often
used in e-commerce.
ICMP
User-Defined
Internet Control Message Protocol is
often used for diagnostic or routing
purposes.
ICQ
UDP
4000
This is a popular Internet chat
program.
IGMP
(MULTICAST)
User-Defined
Internet Group Multicast Protocol is
used when sending packets to a
specific group of hosts.
IKE
UDP
500
The Internet Key Exchange algorithm
is used for key distribution and
management.
IRC
TCP/UDP
6667
This is another popular Internet chat
program.
MSN Messenger
TCP
1863
Microsoft Networks messenger
service uses this protocol.
MES-2110 Users Guide
Appendix B Common Services
Table 87 Commonly Used Services (continued)
NAME
PROTOCOL
PORT(S)
DESCRIPTION
NEW-ICQ
TCP
5190
An Internet chat program.
NEWS
TCP
144
A protocol for news groups.
NFS
UDP
2049
Network File System - NFS is a client/
server distributed file service that
provides transparent file sharing for
network environments.
NNTP
TCP
119
Network News Transport Protocol is
the delivery mechanism for the
USENET newsgroup service.
PING
User-Defined
Packet INternet Groper is a protocol
that sends out ICMP echo requests to
test whether or not a remote host is
reachable.
POP3
TCP
110
Post Office Protocol version 3 lets a
client computer get e-mail from a
POP3 server through a temporary
connection (TCP/IP or other).
PPTP
TCP
1723
Point-to-Point Tunneling Protocol
enables secure transfer of data over
public networks. This is the control
channel.
PPTP_TUNNEL
(GRE)
User-Defined
47
PPTP (Point-to-Point Tunneling
Protocol) enables secure transfer of
data over public networks. This is the
data channel.
RCMD
TCP
512
Remote Command Service.
REAL_AUDIO
TCP
7070
A streaming audio service that
enables real time sound over the web.
REXEC
TCP
514
Remote Execution Daemon.
RLOGIN
TCP
513
Remote Login.
RTELNET
TCP
107
Remote Telnet.
RTSP
TCP/UDP
554
The Real Time Streaming (media
control) Protocol (RTSP) is a remote
control for multimedia on the
Internet.
SFTP
TCP
115
Simple File Transfer Protocol.
SMTP
TCP
25
Simple Mail Transfer Protocol is the
message-exchange standard for the
Internet. SMTP enables you to move
messages from one e-mail server to
another.
SNMP
TCP/UDP
161
Simple Network Management
Program.
SNMP-TRAPS
TCP/UDP
162
Traps for use with the SNMP
(RFC:1215).
MES-2110 Users Guide
223
Appendix B Common Services
Table 87 Commonly Used Services (continued)
224
NAME
PROTOCOL
PORT(S)
DESCRIPTION
SQL-NET
TCP
1521
Structured Query Language is an
interface to access data on many
different types of database systems,
including mainframes, midrange
systems, UNIX systems and network
servers.
SSH
TCP/UDP
22
Secure Shell Remote Login Program.
STRM WORKS
UDP
1558
Stream Works Protocol.
SYSLOG
UDP
514
Syslog allows you to send system logs
to a UNIX server.
TACACS
UDP
49
Login Host Protocol used for (Terminal
Access Controller Access Control
System).
TELNET
TCP
23
Telnet is the login and terminal
emulation protocol common on the
Internet and in UNIX environments. It
operates over TCP/IP networks. Its
primary function is to allow users to
log into remote host systems.
TFTP
UDP
69
Trivial File Transfer Protocol is an
Internet file transfer protocol similar
to FTP, but uses the UDP (User
Datagram Protocol) rather than TCP
(Transmission Control Protocol).
VDOLIVE
TCP
7000
Another videoconferencing solution.
MES-2110 Users Guide
APPENDIX
Legal Information
Copyright
Copyright 2009 by ZyXEL Communications Corporation.
The contents of this publication may not be reproduced in any part or as a whole,
transcribed, stored in a retrieval system, translated into any language, or
transmitted in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, photocopying, manual, or otherwise, without the prior written
permission of ZyXEL Communications Corporation.
Published by ZyXEL Communications Corporation. All rights reserved.
Disclaimer
ZyXEL does not assume any liability arising out of the application or use of any
products, or software described herein. Neither does it convey any license under
its patent rights nor the patent rights of others. ZyXEL further reserves the right
to make changes in any products described herein without notice. This publication
is subject to change without notice.
Trademarks
ZyNOS (ZyXEL Network Operating System) is a registered trademark of ZyXEL
Communications, Inc. Other trademarks mentioned in this publication are used for
identification purposes only and may be properties of their respective owners.
Certifications
Federal Communications Commission (FCC) Interference Statement
This device complies with Part 15 of FCC rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference.
MES-2110 Users Guide
225
Appendix C Legal Information
This device must accept any interference received, including interference that
may cause undesired operations.
FCC Warning
This device has been tested and found to comply with the limits for a Class A
digital switch, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a commercial
environment. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this device in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
CE Mark Warning:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Taiwanese BSMI (Bureau of Standards, Metrology and Inspection) A
Warning:
Notices
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la classe A est conforme la norme NMB-003 du
Canada.
CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASS 1
PRODUCT COMPLIES WITH 21 CFR 1040.10 AND 1040.11.
PRODUIT CONFORME SELON 21 CFR 1040.10 ET 1040.11.
226
MES-2110 Users Guide
Appendix C Legal Information
Viewing Certifications
1
Go to http://www.zyxel.com.
Select your product on the ZyXEL home page to go to that product's page.
Select the certification you wish to view from this page.
ZyXEL Limited Warranty
ZyXEL warrants to the original end user (purchaser) that this product is free from
any defects in materials or workmanship for a period of up to two years from the
date of purchase. During the warranty period, and upon proof of purchase, should
the product have indications of failure due to faulty workmanship and/or
materials, ZyXEL will, at its discretion, repair or replace the defective products or
components without charge for either parts or labor, and to whatever extent it
shall deem necessary to restore the product or components to proper operating
condition. Any replacement will consist of a new or re-manufactured functionally
equivalent product of equal or higher value, and will be solely at the discretion of
ZyXEL. This warranty shall not apply if the product has been modified, misused,
tampered with, damaged by an act of God, or subjected to abnormal working
conditions.
Note
Repair or replacement, as provided under this warranty, is the exclusive remedy of
the purchaser. This warranty is in lieu of all other warranties, express or implied,
including any implied warranty of merchantability or fitness for a particular use or
purpose. ZyXEL shall in no event be held liable for indirect or consequential
damages of any kind to the purchaser.
To obtain the services of this warranty, contact your vendor. You may also refer to
the warranty policy for the region in which you bought the device at http://
www.zyxel.com/web/support_warranty_info.php.
Registration
Register your product online to receive e-mail notices of firmware upgrades and
information at www.zyxel.com for global products, or at www.us.zyxel.com for
North American products.
MES-2110 Users Guide
227
Appendix C Legal Information
228
MES-2110 Users Guide
Index
Index
IGMP 125
jumbo frames 75
link aggregation 119
loop detection 71
MAC filtering 154
multicast 125
MVR 129
port mirroring 115
ports 65
QoS 158
trunking 119
VLAN 99
A
abnormal traffic detection 175
accounts 172
alarms 170
application
backbone 19
bridging 20
metropolitan 22
trunking 21
VLAN 21
ARP inspection 141, 147
configuration file 177
auto negotiation 66
connection test 173
console port 30, 165
console port (accessing the CLI) 179
B
backbone application 19
bandwidth control 111
BPDU 90
date/time 168
bridge 89
BPDU 90
configuration 92
path cost 89, 93
port states 91
priority 93
DHCP
Option 82 137
relay agent information 137
Bridge Protocol Data Unit, see BPDU
bridging application 20
broadcast 123
DHCP binding 145
DHCP client 62, 63
DHCP snooping 141, 142, 143
DoS 174
duplex 66
broadcast storm control 113
E
C
configuration
bandwidth control 111
bridge 89, 92
broadcast storm control 113
date/time 168
DHCP snooping 143
MES-2110 Users Guide
external authentication server 84
F
firmware upgrade 176
flow control 66
229
Index
forward delay 93
forwarding frames 98
front panel 29
G
Gigabit Ethernet ports 30
L
LEDs 35
link aggregation 117
configuration 119
dynamic 117
hash mode 120
ID 118
static 118
status 121
system priority 121
lockout 59
login 51, 179
hardware
console port 30
front panel 29
Gigabit Ethernet ports 30
installation 25
LEDs 35
mini-GBIC slots 31
logout 181
logs 170
loop detection 71
hash mode 120
Hello Time 93
help (in the CLI) 180
I
IEEE 802.1x
port authentication 77
IGMP 123
configuration 125
snooping 123
installing hardware 25
IP address 62
IP DSCP priority 161
IP source guard 141
ARP inspection 147
configuration 143
DHCP snooping 142
MAC filtering 151
configuration 154
MAC learning 153
management 165
abnormal traffic detection 175
alarms 170
configuration file 177
connection test 173
console port 30, 165
date/time 168
DoS 174
firmware upgrade 176
logs 170
reset 178
SNMP 166
user accounts 172
web configurator 51
management VLAN 109
max age 93
metropolitan application 22
mini-GBIC slots 31
J
jumbo frames 75
multicast 123
configuration 125, 129
IGMP snooping 123
MVR 127
Multicast VLAN Registration, see MVR
230
MES-2110 Users Guide
Index
MVR 127
configuration 129
RSTP 89
BPDU 90
bridge priority 93
configuration 92
path cost 89, 93
port states 91
naming the system 62
navigation panel 54
P
password 58
path cost 89, 93
port authentication
and RADIUS 84
port configuration 65
port mirroring 115
port-based VLANs 99
power module
current rating 34
power wire 34
priority mode, QoS 159
S
shortcuts 180
SNMP 166
SNTP 168
stacking, VLAN 105
stacking, VLANs 101
static bindings 141
status
IGMP 127
link aggregation 121
MAC filtering 152
multicast 127
ports 67
RMON 68
trunking 121
switch lockout 59
Q
QoS 157
configuration 158
IP DSCP priority 161
port priority 160
priority mode 159
tag priority 161
R
RADIUS 84
advantages 84
and port authentication 84
server 84
system
abnormal traffic detection 175
configuration file 177
connection test 173
DHCP client 62, 63
firmware upgrade 176
information 61
IP address 62
lockout 59
login 51
logs 170
name 62
password 58
reset 59, 178
user accounts 172
Rapid Spanning Tree Protocol, see RSTP
reset 59, 178
TACACS+ 84
RMON status 68
Tag Protocol Identifier, see TPID
MES-2110 Users Guide
231
Index
tag-based VLANs 107
tagged VLANs 97
time/date 168
TPID 103
trunking 117
application 21
configuration 119
dynamic 117
hash mode 120
ID 118
static 118
status 121
system priority 121
U
unicast 123
user accounts 172
V
VLAN 97
application 21
configuration 99
forwarding frames 98
frame formats 104
management VLAN 109
port-based 99
stacking 101, 105
tag format 103
tag-based 107
tagged 97
W
web configurator 51
navigation panel 54
weighted round robin scheduling 157
232
MES-2110 Users Guide
You might also like
- ES1100 Series: 8/16/24 Port Unmanaged Fast Ethernet SwitchNo ratings yetES1100 Series: 8/16/24 Port Unmanaged Fast Ethernet Switch30 pages
- Gs2200-24/24P Series: Intelligent Layer 2 Gbe Switch Intelligent Layer 2 Gbe Switch With PoeNo ratings yetGs2200-24/24P Series: Intelligent Layer 2 Gbe Switch Intelligent Layer 2 Gbe Switch With Poe360 pages
- Xseries 226 Type 8488 & 8648 - Hardware MaintenanceNo ratings yetXseries 226 Type 8488 & 8648 - Hardware Maintenance198 pages
- Ethernet/IP Fieldbus Interface Card: Customer Product Manual Part 1054600 - 04No ratings yetEthernet/IP Fieldbus Interface Card: Customer Product Manual Part 1054600 - 0468 pages
- Quick Reference Includes: - Safety - Setting Up Your Computer - Getting Help and Service - Warranty - Other NoticesNo ratings yetQuick Reference Includes: - Safety - Setting Up Your Computer - Getting Help and Service - Warranty - Other Notices45 pages
- User Manual-XRN-410S, 810S-ENGLISH - Web-0224 PDFNo ratings yetUser Manual-XRN-410S, 810S-ENGLISH - Web-0224 PDF96 pages
- User Guide Types 8099, 8116, 8155, 8156 Types 8157, 8158, 8159, 8160 Types 8215, 9210, 9211No ratings yetUser Guide Types 8099, 8116, 8155, 8156 Types 8157, 8158, 8159, 8160 Types 8215, 9210, 921166 pages
- Lex2 - Microx - Channel Box Sa HRG (2a02274, Rev B)No ratings yetLex2 - Microx - Channel Box Sa HRG (2a02274, Rev B)46 pages
- User'S Guide: Dell™ Powerconnect™ 27Xx SystemsNo ratings yetUser'S Guide: Dell™ Powerconnect™ 27Xx Systems84 pages
- Westermo - Ug - 6643 22601 - l210 f2g Ex ReviNo ratings yetWestermo - Ug - 6643 22601 - l210 f2g Ex Revi28 pages
- EchoLife HG510a Home Gateway User GuideNo ratings yetEchoLife HG510a Home Gateway User Guide23 pages
- Guardmaster Configurable Safety Relay: User ManualNo ratings yetGuardmaster Configurable Safety Relay: User Manual188 pages
- TEW-410APB Wireless 802.11g AP: User's ManualNo ratings yetTEW-410APB Wireless 802.11g AP: User's Manual24 pages
- User Guide: Dell™ Powerconnect™ 28Xx SystemsNo ratings yetUser Guide: Dell™ Powerconnect™ 28Xx Systems184 pages
- User Guide Types 8293, 8294, 8295 Types 9217, 9218, 9219No ratings yetUser Guide Types 8293, 8294, 8295 Types 9217, 9218, 921960 pages
- Electrician''s Guide to Control and Monitoring Systems: Installation, Troubleshooting, and MaintenanceFrom EverandElectrician''s Guide to Control and Monitoring Systems: Installation, Troubleshooting, and MaintenanceNo ratings yet
- Administrator & Helpdesk Interview Questions You'll Most Likely Be AskedFrom EverandAdministrator & Helpdesk Interview Questions You'll Most Likely Be AskedNo ratings yet
- Thomson Electrac HD Linear Actuator Motion Control per CAN BusFrom EverandThomson Electrac HD Linear Actuator Motion Control per CAN BusNo ratings yet
- E-Commerce & E-Business: Submitted To: Submitted byNo ratings yetE-Commerce & E-Business: Submitted To: Submitted by5 pages
- Computer General Knowledge and Computer Question Answers For Competative ExamsNo ratings yetComputer General Knowledge and Computer Question Answers For Competative Exams23 pages
- Loop-IP6340 24 Giga+4 1000 SFP Ports Smart Managed Switch: Features DescriptionNo ratings yetLoop-IP6340 24 Giga+4 1000 SFP Ports Smart Managed Switch: Features Description4 pages
- Microsoft On Demand Certification Tracks UsNo ratings yetMicrosoft On Demand Certification Tracks Us1 page
- PCS Architecture in Wireless CommunicationNo ratings yetPCS Architecture in Wireless Communication17 pages
- Outlook Configuration With Online Exchange and POP3 Mail ImportNo ratings yetOutlook Configuration With Online Exchange and POP3 Mail Import12 pages
- K85005-0137 - FX Series Intelligent Fire Alarm SystemsNo ratings yetK85005-0137 - FX Series Intelligent Fire Alarm Systems8 pages
- Vodacom, Cell C, Telkom, and MTN Subscribers: Zero-Rated UrlsNo ratings yetVodacom, Cell C, Telkom, and MTN Subscribers: Zero-Rated Urls8 pages
- Simple PLC To PLC Communications iQ-R Master To iQ-F SlaveNo ratings yetSimple PLC To PLC Communications iQ-R Master To iQ-F Slave7 pages
