Scribd
Upload
2K views

Design Procedure For Raft Foundation

1. A raft foundation is a continuous footing under all columns and walls that is used when individual footings would cover over half the area or the soil has low bearing capacity. 2. It can be solid, circular, or ribbed to provide structure from beams and be more economical. Uniform thickness is used if loads and column spacing are equal, otherwise moments are considered. 3. Analysis considers soil pressure, shear, and bending diagrams to design for required strength and settlement between the weight of structure and excavation.

Uploaded by

Omkarnath Yadav
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
2K views

Design Procedure For Raft Foundation

1. A raft foundation is a continuous footing under all columns and walls that is used when individual footings would cover over half the area or the soil has low bearing capacity. 2. It can be solid, circular, or ribbed to provide structure from beams and be more economical. Uniform thickness is used if loads and column spacing are equal, otherwise moments are considered. 3. Analysis considers soil pressure, shear, and bending diagrams to design for required strength and settlement between the weight of structure and excavation.

Uploaded by

Omkarnath Yadav
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

DESIGN PROCEDURE FOR RAFT FOUNDATION

DESIGN OF RAFT FOUNDATION


Design Considerations:
If the loads transmitted by the columns in a structure are so heavy or the allowable soil pressure
so small that individual footings would cover more than about one-half of the area, it may be
better to provide a continuous footing under all columns and walls. Such a footing is called a raft
or mat foundation. Raft foundations are also used to reduce the settlement of structures located
above highly compressible deposits. Since rafts are usually at some depth in the ground, a large
volume of excavation may be required. If weight of the excavated soil is equal to the weight of
the structure and that of the raft, and the centres of gravity of excavation and structure coincide,
settlement would be negligible. Where complete compensation is not feasible, a shallower raft
may be accepted if the net increase in loads in small enough to lead to tolerable settlement. A raft
foundation may be rectangular or circular and may be with or without an open as shown in fig.1
and fig.2.

Fig.1: Solid Raft Slab

Fig.2. Circular Raft Foundation

If the columns are equally spaced and loads are not very heavy, a raft may be designed as having
uniform thickness. The conventional design of such a raft consists of establishing its dimensions,
from which the soil pressure at various locations beneath the slab may be computed. The raft is
divided into a series of continuous strips centered on the appropriate columns and rows in both
directions as shown in fig.3. The shear and bending moment diagrams may be drawn using

continuous beam analysis or coefficients for each strip. The depth is selected to satisfy shear
requirements.

Fig.3: Raft foundation with strip centered on columns


The steel requirements will vary from strip to strip. This method gives a conservative design
since the interaction of adjacent strip is neglected.
If the columns are equally spaced and their loads are equal, the pressure on the soil will be
uniform, otherwise moments of the loads may be taken about centre of the base and pressure
distribution determined. Since the equations for this are usually derived for a rigid member and a
raft in general is not a rigid member, the pressure and resulting internal stresses may be seriously
in error if the eccentricity is very large. The weight of the raft is not considered in the structural
design because it is assumed to be carried directly by the subsoil.
Raft may be ribbed where the column spacing is irregular or for economy in using a relatively
thin slab over most of the area as shown in fig.4. Alternatively, rafts may be thickened at the
column locations for economy and depth should be made sufficient to resist shear. A ribbed raft
foundation consists of a slab acted upon by upward soil pressure at its underside and supported
by beams from column at its top which balance the upward pressure with downward column
loads. It is a similar to a floor slab resting on a system of beams and columns. The portion
between beams is designed as a conventional one way or two way slab. If the beams are deep,
they should be designed as deep beams.

Fig.4: Raft foundation with walls as stiffener


Mat or raft foundation is a large concrete slab supporting several columns in two or more rows.
It is used where the supporting soil has low bearing capacity.
The bearing capacity increased by combining all individual footings in to one mat since
bearing capacity is proportional to width and depth of foundations.
In addition to increasing the bearing capacity, mat foundations tend to bridge over irregularities
of the soil and the average settlement does not approach the extreme values of isolated footings.
Thus mat foundations are often used for supporting structures that are sensitive to differential
settlement.

You might also like