Scribd
Upload
138 views2 pages

ITTC Procedure For CFD Application

This document provides guidelines for uncertainty analysis in computational fluid dynamics (CFD) for Reynolds-averaged Navier-Stokes (RANS) codes. It outlines a four-step process for CFD verification and validation: 1) preparation by selecting the code and specifying objectives, geometry, conditions, and benchmarks, 2) verification to assess numerical uncertainty through convergence studies, 3) validation to assess modeling uncertainty by comparing simulations to experimental data, and 4) documentation of the full CFD process and results. The guidelines reference a separate quality management procedure for implementing the uncertainty assessment methodology.

Uploaded by

kyaw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
138 views2 pages

ITTC Procedure For CFD Application

This document provides guidelines for uncertainty analysis in computational fluid dynamics (CFD) for Reynolds-averaged Navier-Stokes (RANS) codes. It outlines a four-step process for CFD verification and validation: 1) preparation by selecting the code and specifying objectives, geometry, conditions, and benchmarks, 2) verification to assess numerical uncertainty through convergence studies, 3) validation to assess modeling uncertainty by comparing simulations to experimental data, and 4) documentation of the full CFD process and results. The guidelines reference a separate quality management procedure for implementing the uncertainty assessment methodology.

Uploaded by

kyaw
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ITTC Recommended

Procedures and Guidelines


CFD, General
Uncertainty Analysis in CFD,
Guidelines for RANS Codes

7.5 03
01 02
Page 1 of 2
Effective Date
1999

Table of Contents
1
2

PURPOSE OF PROCEDURE ..............2


GUIDELINES FOR RANS CODES ....2

INTERIM GUIDELINE

Prepared by

Approved

Resistance Committee of 22nd ITTC


Date

22nd ITTC 1999


Date

Revision
00

ITTC Recommended
Procedures and Guidelines
CFD, General
Uncertainty Analysis in CFD
Guidelines for RANS Codes

7.5 03
01 02
Page 2 of 2
Effective Date
1999

Revision
00

Uncertainty Analysis in CFD, Guidelines for RANS Codes


1 PURPOSE OF PROCEDURE
To provide guidelines for implementation
of QM procedure 7.5-03-01-01, Uncertainty
Analysis in CFD, Uncertainty Assessment Methodology.
2 GUIDELINES FOR RANS CODES
The overall CFD verification and validation procedures can be conveniently grouped in
four consecutive steps: (1) preparation; (2)
verification; (3) validation; and (4) documentation. The section references are to QM procedure 7.5-03-01-01.
Preparation. The 1st step is preparation,
which involves selection of the CFD code and
specification of objectives, geometry, conditions, and available benchmark information.
The objectives might be prediction of certain
variables at certain levels of validation (e.g.,
programmatic validation requirements U reqd ).
The variables can either be integral (e.g., resistance) or point (e.g., mean velocities and turbulent Reynolds stresses) values and the levels of
validation may be different for each variable.
Verification. The 2nd step is verification,
which is defined as a process for assessing
simulation numerical uncertainty U SN and,

when conditions permit, estimating the sign


and magnitude of the simulation numerical

error SN
itself and the uncertainty in its error
referred to as the corrected simulation numerical uncertainty U SC N . Iterative and input parameter convergence studies are conducted
using multiple solutions with systematic parameter, as described in Section 3.2.
Validation. The 3rd step is validation,
which is defined as a process for assessing
simulation modelling uncertainty U SM by using benchmark experimental data and, when
conditions permit, estimating the sign and
magnitude of the simulation modelling error
SM itself. The comparison error E (difference
between data D and simulation S values) and
validation uncertainty U V (combination of uncertainties in data and portion of simulation
uncertainties that can be estimated) are used, as
described in Section 3.3.
Documentation. The 4th step is documentation, which is detailed presentation of the
CFD code (equations, initial and boundary
conditions, modelling, and numerical methods), objectives, geometry, conditions, verification, validation, and analysis.

You might also like