Scribd
Upload
99 views

Lecture2 Air

This document discusses different particulate emission control methods including mechanical separation and wet gas scrubbing. It describes the basic mechanisms and key equipment used for particulate control, including gravitational settling chambers, cyclone separators, fabric filters, and electrostatic precipitators for mechanical separation as well as plate scrubbers, packed-bed scrubbers, and spray scrubbers for wet gas scrubbing. The document provides details on the design, operation, advantages, and disadvantages of each method.

Uploaded by

Raj Bakhtani
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
99 views

Lecture2 Air

This document discusses different particulate emission control methods including mechanical separation and wet gas scrubbing. It describes the basic mechanisms and key equipment used for particulate control, including gravitational settling chambers, cyclone separators, fabric filters, and electrostatic precipitators for mechanical separation as well as plate scrubbers, packed-bed scrubbers, and spray scrubbers for wet gas scrubbing. The document provides details on the design, operation, advantages, and disadvantages of each method.

Uploaded by

Raj Bakhtani
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

[1]

Lecture 2
Particulate emission control by mechanical
separation & wet gas scrubbing

PARTICULATE EMISSION CONTROL BY MECHANICAL SEPARATION


The basic mechanism of removing particulate matter from gas stream is classified as: 1)
gravitational settling 2) centrifugal impaction 3) inertial impaction 4) direct interception 5)
diffusion and 6) electrostatic precipitation.
Equipment presently available, which make use of one or more of the above mechanisms,
fall into the following five broad categories: 1) gravitational settling chambers 2) cyclone
separators 3) fabric filters 4) electrostatic precipitator
[A] Gravitational Settling Chambers
Gravitational settling chambers are generally used to remove large, abrasive particles
(usually >50 m) from gas stream. It provides enlarged areas to minimize horizontal velocities
and allow time for the vertical velocity to carry the particle to the floor. The usual velocity
through settling chambers is between 0.5 to 2.5 m/s.

Figure 2.2.1: Gravitation settling chamber [1]


Advantage: Low pressure loss, simplicity of design and maintenance.
Disadvantage: Requires larger space and efficiency is low. Only larger sized particles are
separated out.

Design of a gravitational settling chamber


If we assume that Stokes law applies we can derive a formula for calculating the
minimum diameter of a particle collected at 100% theoretical efficiency in a chamber of length
L.
vt
v
h
H
L

Where vt=terminal settling velocity, m/s

(2.2.1)

vt

g p a d p2
9 a

(2.2.2)

Where, g=gravitational constant, m/s2; p=density of particle, kg/m3; a=density air,


kg/m3; dp=diameter of particle, m; a=viscosity of air, kg/m s; H=height of settling chamber, m;
vh=horizontal flow-through velocity, m/s; and L=length of settling chamber, m.
Solving for dp gives an equation that predicts the largest-size particle that can be removed
with 100% efficiency from a settling chamber of given dimension.

18 a Hvh

dp
gL
p
a

(2.2.3)

All particles larger than dp will also be removed with 100% efficiency, while the
efficiency for smaller particles is the ratio of their settling velocities to the settling velocity of the
dp particle.

[B] Cyclone Separators


A cyclone separator consists of a cylindrical shell, conical base, dust hopper and an inlet
where the dust-laden gas enters tangentially. Under the influence of the centrifugal force
generated by the spinning gas, the solid particles are thrown to the wall of the cyclone as the gas
spirals upward at the inside of the cone. The particles slide down the walls of the cone and into
the hopper. The operating efficiency of a cyclone depends on the magnitude of the centrifugal
force exerted on the particles. The greater the centrifugal force, the greater the spreading
efficiency. The magnitude of the centrifugal force generated depends on particle mass, gas
velocity within the cyclone, and cyclone diameter.

Fc M p

vi2
R

(2.2.4)

Where, Fc=centrifugal force, N; Mp=particulate mass, Kg; vi equals particle velocity and
R equals radius of the cyclone, m/s. From this equation, it can be seen that the centrifugal force
on the particles, and thus the collection efficiency of the cyclone collector can be increased by
decreasing R. Large-diameter cyclone have good collection efficiencies for particles 40 to 50 m
in diameter.

Advantage: Relatively inexpensive, simple to design and maintain; requires less floor area; low
to moderate pressure loss.
Disadvantage: Requires much head room; collection efficiency is low for smaller particles,
quite sensitive to variable dust loading and flow rates.

[C] Fabric Filters


In a fabric filter system, the particulate-laden gas stream passes through a woven or felted
fabric that filters out the particulate matter and allows the gas to pass through. Small particles are
initially retained on the fabric by direct interception, inertial impaction, diffusion, electrostatic
attraction, and gravitational settling. After a dust mat has formed on the fabric, more efficient
collection of submicron particle is accomplished by sieving.
Filter bags usually tubular or envelope-shaped, are capable of removing most particles as
small as 0.5m and will remove substantial quantity of particles as small as 0.1 m. Filter bags
ranging from 1.8 to 9 m long, can be utilized in a bag house filter arrangement.
As particulates build up on the inside surface of the bags, the pressure drop increases.
Before the pressure drop becomes too severe, the bag must be relieved of some of the particulate
layer. Fabric filter can be cleaned intermittently, periodically, or continuously [2].
Fabric and Fibre Characteristics: Fabric filter may be classified according to filtering media:
woven fabric or felt cloth. Woven fabrics have a definite long range repeating pattern and have
considerable porosity in the direction of gas flow. These open spaces must be bridged by
impaction of interception to form a true filtering surface. Felted cloth consists of randomly
oriented fibres, compressed into a mat and needled to some loosely woven backing material to
improve mechanical strength. The choice of fabric fibre is based primarily on operating
temperature and the corrosiveness or abrasiveness of the particle. Cotton is the least expensive
fibre, and is preferably used in low temperature dust collection service. Silicon coated glass fibre
cloth is commonly employed in high temperature applications. The glass fibre must be lubricated
to prevent abrasion. All fibre may be applied to the manufacture of woven and felt type fabrics.
Fabric Filter System: Fabric filter systems typically consist of a tubular bag or an envelope,
suspended or mounted in such manner that the collected particles fall into hopper when
dislodged from fabric. The structure in which the bags are hanged is known as a bag-house.

Generally, particle laden gas enters the bag at the bottom and passes through the fabric
while the particles are deposited on the inside of the bag. The cleaning is accomplished by
shaking at fixed intervals of time [3].

Figure 2.2.2: Typical bag-house


Advantage: Fabric filters can give high efficiency, and can even remove very small particles in
dry state.
Disadvantage: High temperature gasses need to be cooled. The flue gasses must be dry to avoid
condensation and clogging. The fabric is liable to chemical attacks.

[D] Electrostatic Precipitator


The electrostatic precipitator is one of the most widely used device for controlling
particulate emission at industrial installations ranging from power plants, cement and paper mills
to oil refineries. Electrostatic precipitator is a physical process by which particles suspended in
gas stream are charged electrically and, under the influence of the electrical field, separated from
the gas stream.

The precipitator system consists of a positively charged collecting surface and a highvoltage discharge electrode wire suspended from an insulator at the top and held in passion by
weight t the bottom. At a very high DC voltage, of the order of 50kV, a corona discharge occurs
close to the negative electrode, setting up an electric field between the emitted and the grounded
surface [4].
The particle laden gas enters near the bottom and flows upward. The gas close to the
negative electrode is, thus, ionized upon passing through the corona. As the negative ions and
electrons migrate toward the grounded surface, they in turn charge the passing particles. The
electrostatic field then draws the particles to the collector surface where they are deposited.
Periodically, the collected particles must be removed from the collecting surface. This is done by
rapping or vibrating the collector to dislodge the particles. The dislodged particles drop below
the electrical treatment zone and are collected for ultimate disposal [5].
Advantage:

Maintenance is nominal, useless corrosive and adhesive materials are present in flue
gases.

They contain few moving parts.

They can be operated at high temperature up to 300oC-450o C.

Disadvantage:

Higher initial cost.

Sensitive to variable dust loading and flow rates.

They use high voltage, and hence may pose risk to personal safety of the staff.

Collection efficiency reduces with time.

PARTICULATE EMISSION CONTROL BY WET GAS SCRUBBING


Wet scrubber removes particulate matter from gas streams by incorporating the particles
into liquid droplets directly on contact. The basic function of wet scrubber is to provide contact
between the scrubbing liquid, usually water and, the particulate to be collected. This contact can
be achieved in a variety of ways as the particles are confronted with so-called impaction target,
which can be wetted surface as in packed scrubbers or individual droplets as in spray scrubbers
[3]. The basic collection mechanism is the same as in filters: inertial impaction, interception and
diffusion. Generally, impaction and interception are the predominant mechanism for particles of

diameter above 3 m, and for particle of diameter below 0.3 m diffusion begins to prevail.
There are many scrubber designs presently available where the contact between the scrubbing
liquid and the particles is achieved in a variety of ways. The major types are: plate scrubber,
packed-bed scrubber, spray scrubber, venturi scrubber, cyclone scrubber, baffle scrubber,
impingement-entrainment scrubber, fluidized-bed scrubber.
[A] Plate scrubber
It contains a vertical tower containing one or more horizontal plates (trays). Gas enters
the bottom of the tower and must pass through perforations in each plate as it flows
countercurrent to the descending water stream. Collection efficiency increases as the diameter of
the perforations decreases. A cut diameter, that collected with 50% efficiency, of about

aerodynamic diameter can be achieved with 3.2-mm-diameter holes in a sieve plate.


[B] Packed bed scrubber
Operates similarly to packed-bed gas absorber. Collection efficiency increases as packing
size decreases. A cut diameter of 1.5 m aerodynamic diameter can be attained in columns
packed with 2.5 cm elements.

Figure 2.4.1: Packedbed scrubber

[C] Spray scrubber


Particles are collected by liquid drops that have been atomized by spray nozzles.
Horizontal and vertical gas flows are used, as well as spray introduced co-current,
countercurrent, or cross-flow to the gas.
Collection efficiency depends on droplet size, gas velocity, liquid/gas ratio, and droplet
trajectories. For droplets falling at their terminal velocity, the optimum droplet diameter for fineparticle collection lies in the range 100 to 500

m.

Gravitational settling scrubbers can achieve cut diameters of about 2.0 m. The
liquid/gas ratio is in the range 0.001 to 0.01 m3/ m3 of gas treated.
[D] Venturi scrubber
A moving gas stream is used to atomize liquids into droplets. High gas velocities (60 to
120 m/s) lead to high relative velocities between gas and particles and promote collection.
[E] Cyclone scrubber
Drops can be introduced into the gas stream of a cyclone to collect particles. The spray
can be directed outward from a central manifold or inward from the collector wall.
[F] Impingement-Entrainment Scrubber:
The gas is forced to impinge on a liquid surface to reach a gas exit. Some of the liquid
atomizes into drops that are entrained by the gas. The gas exit is designed so as to minimize the
loss of entrained droplets.
[G] Fluidized-bed scrubber
A zone of fluidized packing is provided where gas and liquid can mix intimately. Gas
passes upward through the packing, while liquid is sprayed up from the bottom and/or flows
down over the top of the fluidized layer of packing [6].

REFERENCES
[1]

Rao, C. S. Environmental Pollution Control Engineering, 2nd Edition, New Age


International, New Delhi, 2006.

[2]

Spellman, F. R. The Science of Air Concepts and Applications 2nd Edition, Taylor and
Francis (CRC Press), 2008.

[3]

http://www.cpcb.nic.in/oldwebsite/New%20Item/chapter-15.html

[4]

Theodore, L. Electrostatic Precipitators in Air Pollution Control Equipment


Calculations, Wiley, 2008.

[5]

http://www.teriin.org/envis/times1-1.pdf

[6]

Jumah, R. Y., A. S. Mujumdar. Handbook of Industrial Drying: Dryer Emission Control


Systems, 3rd Edition, CRC Press, 2006.

You might also like