Scribd
Upload
120 views

Flow Control, 3 Way, PR & Temp Compensated, NG6, Type RPC1-T3

This document describes a pressure and temperature compensated three-way flow control valve. It contains: 1) An overview of the valve's operating principle to control flow sent to an actuator and discharge excess back to the tank. 2) Details on the valve's adjustment knob range, indicator, and locking screw. 3) Specifications for the valve including maximum pressure and flow rates, temperature ranges, viscosity, and contamination degree.

Uploaded by

Libin
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
120 views

Flow Control, 3 Way, PR & Temp Compensated, NG6, Type RPC1-T3

This document describes a pressure and temperature compensated three-way flow control valve. It contains: 1) An overview of the valve's operating principle to control flow sent to an actuator and discharge excess back to the tank. 2) Details on the valve's adjustment knob range, indicator, and locking screw. 3) Specifications for the valve including maximum pressure and flow rates, temperature ranges, viscosity, and contamination degree.

Uploaded by

Libin
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

32 250/110 ED

RPC1-T3

PRESSURE AND TEMPERATURE


COMPENSATED THREE-WAY
FLOW CONTROL VALVE
SERIES 41

SUBPLATE MOUNTING
ISO 6263-03 (CETOP 03)
p max 250 bar
Q max (see table of performances)
MOUNTING INTERFACE

OPERATING PRINCIPLE

ISO 6263-03-03-*-97
(CETOP 4.5.2-3-03-250)

40.5
30.2
21.5
12.7
0.75

5.1
T
31

15.5

The pressure and temperature compensated three-way


flow control valves serve to control the flow sent to the
actuator and to discharge it, which exceeds that required,
back to tank at system pressure rather than at relief value
pressure.

31.75

The flow rate adjustment range is carried out with three


turns of the knob and an indicator shows the number of
turns made. A one-turn adjustment on the knob,
RPC1*/M, is available upon request.

7.5 (max)
M5

The adjustment knob can be locked in any position in the


adjustment range by a screw.

PERFORMANCES

HYDRAULIC SYMBOL

(obtained with mineral oil with viscosity of 36 cSt at 50C)

Maximum operating pressure


Minimum pressure difference between A and B
Maximum controlled flow rates
Minimum controlled flow rate (for 1 and 4 l/min)

bar

250
12

l/min

1-4-10-16-22
0,035

Ambient temperature range

-20 / +50

Fluid temperature range

-20 / +80

Fluid viscosity range

cSt

10 400

According to ISO 4406:1999 class 20/18/15


Fluid contamination degree
Fluid contamination degree for flows < 0,5 l/min According to ISO 4406:1999 class 18/16/13

Recommended viscosity

cSt

25

Mass

kg

1,5

RPC1/T3
RPC1-/T3/M

3
1

Number of adjustment knob turns


32 250/110 ED

1/4

RPC1-T3
SERIES 41

1 - IDENTIFICATION CODE

R P C 1 -

/ T 3 /

Seals: omit for


mineral oils
V = viton for special
fluids

Pressure compensated
flow control valve

Size ISO6263-03 (CETOP 03)


Controlled flow:

/ 41 /

Series No. (the overall and


mounting dimensions remain
unchanged from 40 to 49)

1 = 1 l/min
4 = 4 l/min
10 = 10 l/min
16 = 16 l/min
22 = 22 l/min

M = single-turn adjustment knob


(omit for three-turn adjustment)

Temperature compensation

Number of ways

2 - CHARACTERISTIC CURVES (values obtained with viscosity of 36 cSt at 50C)


ADJUSTMENT

KNOB TURNS

3 - HYDRAULIC FLUIDS
Use mineral oil-based hydraulic fluids HL or HM type, according to
ISO 6743-4. For these fluids, use NBR seals. For fluids HFDR type
(phosphate esters) use FPM seals (code V). For the use of other
kinds of fluid such as HFA, HFB, HFC, please consult our technical
department. Using fluids at temperatures higher than 80 C causes
a faster degradation of the fluid and of the seals characteristics.
The fluid must be preserved in its physical and chemical
characteristics.

5 - TEMPERATURE COMPENSATION
The valve temperature compensation is obtained with the principle
of fluid passage across a thin wall orifice in which the flow rate is not
subtantially influenced by the oil viscosity fluctuations. For
controlled flows of less than 0,5 l/min and with a temperature
difference of 50 C, flow is increased by about 13% of the set flow
value. For higher flow rates, and with the same temperature
difference, the flow increase is about 4% of the maximum flow
controlled by the valve.

4 - PRESSURE COMPENSATION
Two throttles in series are in the valve. The first is an opening
regulated by the knob; the second, piloted by the pressure
upstream and downstream of the first throttle, assures a constant
pressure drop across the adjustable throttle. In these conditions, the
set flow rate value stays constant within a tolerance range of 2%
of the maximum flow controlled by the valve for maximum pressure
variation between the intake and outlet chambers of the valve.

32 250/110 ED

2/4

RPC1-T3
SERIES 41

6 - OVERALL AND MOUNTING DIMENSIONS


dimensions in mm

FASTENING BOLTS
4 bolts M5x90
Tightening torque: 5 Nm

7 - APPLICATION EXAMPLE

Mounting surface with sealing rings:


3 OR type 2037 (9.25x1.78) - Shore 90

Adjustment knob

Indicator of knob turns

Knob locking screw

8 - SUBPLATES (see datasheet 51 000)

Type

PMMD-AI3G
with rear ports
with user P plugged

Type

PMMD-AL3G
with side ports
with user P plugged

Port dimension

3/8 BSP

B
T

32 250/110 ED

3/4

RPC1-T3
SERIES 41

DUPLOMATIC OLEODINAMICA S.p.A.

20015 PARABIAGO (MI) Via M. Re Depaolini 24


Tel. +39 0331.895.111
Fax +39 0331.895.339
www.duplomatic.com e-mail: [email protected]

32 250/110 ED

REPRODUCTION IS FORBIDDEN. THE COMPANY RESERVES THE RIGHT TO APPLY ANY MODIFICATIONS.

4/4

You might also like