ProEXR

Advanced OpenEXR plug-ins

ProEXR
by Brendan Bolles
Version 1.9.1
February 25, 2016
fnord software
671 Ashbury Street
San Francisco, CA 94117
www.fnordware.com
For support, comments, feature requests, and insults, send email to [email protected] or
participate in the After Effects email list, available through www.media-motion.tv.
Plain English License Agreement
You know the drill. While actually much of the software in this package is free, not all of it is (specifically ProEXR for Photoshop, ProEXR AE for After Effects, and ProEXR for Premiere). If you
use it past the trial period, you should buy it. If other people you know want to use it too, they
should buy their own copies. Companies should buy a copy for every employee who uses it. The
license is tied to the person, so if you use ProEXR on multiple computers you may freely install
your one serial number on each.

A lot of work went into writing these plug-ins and creating this manual. If a few people pay for
them, Ill go out and make some more neat-o graphics plug-ins. I promise.
Oh, and please enjoy using this software. Really, I insist.
20072016 fnord. All rights reserved.
2

About ProEXR
Industrial Light and Magics (ILMs) OpenEXR format has quickly gained wide adoption in the
high-end world of computer graphics. Its now the preferred output format for most 3D renderers
and is starting to become the standard for digital film scanning and printing too.
But while many programs have basic support for the format, hardly any provide full access to all of
its capabilities. And OpenEXR is still being developednew compression strategies and other
features are being added while some big application developers are not interested in keeping up.
And thats where ProEXR comes in. It fully supports OpenEXR in Adobe Photoshop, After Effects, and Premiere Pro, at least to the extent that its reasonably possible to do so in those programs. In particular, ProEXR does these things that Adobes shipping plug-ins do not:
It can read in all the channels present in an EXR, not just the standard R, G, B, and A.
It can output layers from Photoshop and After Effects, following OpenEXR layer-channel
naming conventions.
It reads and writes information about the projects color space.
It can greatly reduce a files size through Luminance/Chroma subsampling.
It can save images in 32-bit float as well as 16-bit float.
In this manual, ProEXR refers to the entire suite of plug-ins, although most of the After Effects
plug-ins actually ship with the program and are open source. But since they are developed in parallel and share the OpenEXR codebase, it makes sense to talk about them together.

System Requirements
To use ProEXR, youll need Photoshop and After Effects versions CS3 or later. Photoshop
Extended is required for layered floating point files in CS6 and earlier. For Premiere, youll need
version CS6 or later.

Installation
Photoshop
Drag ProEXR or ProEXR EZ to Photoshops plug-in folder. As of CS5, Photoshops built-in
OpenEXR plug-in can not be disabled, but ProEXR will work alongside it and take priority over it.
After Effects
After Effects CS4 and later already ship with three of the ProEXR plug-ins: OpenEXR (in Plugins/Format), EXtractoR, and IDentifier (in Plug-ins/Effect). If you want to upgrade to the latest
versions, replace them with the ones included in the ProEXR package.

In addition, youll want to install the ProEXR AE plug-in, which provides automatic comp creation and layered file export. This plug-in is not included with After Effects.
Premiere
Premiere ships with the OpenEXR plug-in as of the November 2015 update to Premiere CC 2015.
If you use a previous version, drop the OpenEXR plug-in into a place where both Premiere and
Adobe Media Encoder can see it. Here are the folders for each platform (replace 7.0 with CS6
if youre using CS6):

Mac

/Library/Application Support/Adobe/Common/Plug-ins/7.0/MediaCore

Windows

C:\Program Files\Adobe\Common\Plug-ins\7.0\MediaCore

Quick Start
If you need a multi-channel EXR file to try out the extra features in ProEXR, download one here:
http://www.fnordware.com/OpenEXR/x35_3a.exr
This file was created by Rob Nederhorst.

A sample After Effects project using this file is also available.

Photoshop
To save an EXR, your document must be in 32 Bits/Channel mode, as
set from the Image menu. Any OpenEXR files you read in will already
be set to this mode.

Go to File Save As. Select ProEXR (or ProEXR EZ) as the Format.

Configure settings in the Options dialog. Click OK.

Alternatively, you can export a series of layers as individual EXR files by choosing File Export
ProEXR Layer Export.

When opening an .exr file in Photoshops Open dialog, ProEXR should appear as the format and
any additional channels should appear as extra layers.
After Effects
Import and render OpenEXR like any other format. The
Footage status information tells you which compression
method was used and which extra channels are included in
the file, if any.

To access the extra channels, use one of the plug-ins in the

3D Channel category, particularly EXtractoR or IDentifier.
Or select the EXR file and choose Create ProEXR Layer
Comps from the File menu and a series of comps will be
created and configured for you.
Premiere
With the plug-in installed, OpenEXR file sequences be be available through the standard import
dialog and OpenEXR will be a format option in Premieres Export Media dialog.

Common Issues
When users write to us to say that ProEXR doesnt appear to be working, 99% of the time its because the instructions above werent followed closely. The most common mistakes are:
1. Opening files with the built-in Photoshop plug-in. Verify that ProEXR is the format used in
the Open dialog.
2. Not running Photoshop Extended, which is required to open and save multi-layered
OpenEXR files in CS6 and earlier. ProEXR EZ can be used with regular Photoshop.
6

3. Installing the 32-bit version of the plug-in in the 64-bit version of the program. To verify ProEXR is installed in Photoshop, find the About Plug-In menu and see if ProEXR is listed.
4. Installing ProEXR EZ and loading a multi-layer EXR. Only full ProEXR (without EZ) will
show the extra layers.

Registration
Many of the plug-ins in this package are free, but ProEXR for
Phothsop, ProEXR AE for After Effects, and ProEXR for
Premiere are not. After installation, you are given 15 days to
try them out before they will refuse to run any longer without a serial number. To purchase a serial number, visit this
link:
http://www.fnordware.com/ProEXR/buy_proexr.html

ProEXR History
The plug-ins in this package began their life while I was working as a visual effects artist and occasional programmer at The Orphanage. Around 2002, HDR images and floating point compositing
were becoming all the rage at Siggraph and other places but After Effects, with its 16-bit limitation, was largely left out of the party.
To try to work around this, Stu Maschwitz, Ryan Tudhope, myself, and other Orphans created
eLin, originally through some AE presets and later through custom plug-ins I wrote. These plugins were first used on Hellboy, and then refined for The Day After Tomorrow. They seemed to do
the trick, so eLin was released as a commercial package around this time. The release also con-

tained our first OpenEXR format modulea Photoshop plug-in that presented images to AE in
log space.
When ramping up on Sin City, the need to access 3D Channels in an EXR was apparent, so an AEnative plug-in was created that could pass on Z-Depth and Velocity channels. Most of the motion
blur in our shots was rendered in After Effects using the Velocity channels.
Years later, there was some talk of updating the AE plug-in for After Effects 7, which finally had
real floating point but no 3D channel support for EXR files. The Orphanage graciously agreed to
let me take the code I had written there and release it publicly. Everything was fine until Steve Cho
sent me an image by Rob Nederhorst that didnt just have a few standard 3D channels, but a total
of 49 channels containing various render passes, image layers, velocity channels, etc. Steve mentioned that Nuke could easily pull all the channels from this file, and so I decided I had to get the
same functionality into After Effects, which involved writing some additional 3D channel plug-ins
as well as generalizing the format importer.
At some point in this process, it occurred to me that a similar plug-in would also be great to have
in Photoshop. While the interface for loading layers into Photoshop was completely undocumented, I managed to figure it out and was amazed that it all actually worked more or less. Several
versions later I added layered exporting to After Effects as well as Premiere Pro support.
And now after all that, Im really excited to get to use ProEXR in my own work. And even more
excited to share it with the global graphics communityand you (awwww).

Acknowledgments
First and foremost, I have to thank everyone who has contributed to the OpenEXR code at ILM.
After all, their code makes up the bulk of this package. I have the individual contributors names
listed later on in this manual.
Special thanks to Florian Kainz for heading up the project at ILM and for answering many of my
stupid questions.
Thanks also to whatever corporate big-wig(s) at ILM decided it was OK to release the OpenEXR
code to the public. We all owe you.
Thank you to the After Effects team at Adobe, who make a program I really love using. Special
thanks to Dan Wilk (DWilk), Dave Simons (DaveS), Bruce Bullis (bbb), Vladimir Potapyev
(Vlad), and Zac Lam (Zac) who have helped me fix my own bugs, fixed some of their own, and
generally helped me figure out whats going on.
Thanks to Lars Borg, Manish Kulkarni, and Tom Raurk also from Adobe, who have helped me
over the years.
Thanks to everyone I have ever worked with at The Orphanage. Especially Stu Maschwitz, Luke
OByrne, Alex Prichard, Ralph Procida, Tim Dobbert, Ben Grossmann, and Steve Cho.
Thanks to Jean-loup Gailly and Mark Adler for zlib. Thanks to Marti Maria for Little CMS. Both
open source libraries are used throughout ProEXR.
Thanks to everyone who buys these plug-insit really means a lot to me.
And thanks to everyone else who ought to be listed here, but is escaping my mind as I write this at
4:45 in the morning.
9

ProEXR in Photoshop
ProEXR vs. ProEXR EZ
In Photoshop, two different plug-ins are provided: the full-featured ProEXR plug-in and a simpler
version called ProEXR EZ. Heres a quick comparison:
ProEXR

Free

Multiple Layers/Channels

Layer Exporting

Always creates standard RGBA EXRs

Can use Photoshop Grayscale mode

Alpha always appears in a layer

Alpha can appear in the Channels palette

10

ProEXR EZ

Most users will want to install either ProEXR or ProEXR EZ. If you choose to install both, files
dragged to Photoshop will open with the full ProEXR. ProEXR EZ is a simpler plug-in, augmenting the Photoshop version with a few options. The rest of this section describes the full ProEXR.

File Reading
The OpenEXR format can support any number of channels,
each one defined by a unique name. But most readers (including Adobes) only pay attention to the channels R, G, B,
and A to create a single image. ProEXR reads those channels
along with any other image channel found in the file.
The best way to see how ProEXR works is to open a multichannel EXR file with it. Each channel will appear, with some
channels grouped together in layers. For more information
about how layers are formed from channels in an EXR, see
Channel Info.
By default, each layer will be given transparency if an alpha
channel (A) is present in the file or if a layer is explicitly assigned its own alpha. For ways to override this behavior, see
Import Options.
OpenEXR files always appear in Photoshop in 32-bit (float)
mode.

11

File Writing
ProEXR will appear as a format option in the Save As dialog when your document is in 32-bit
(float) mode. Unlike most other formats, you will be allowed to save your Photoshop layers. You
will then be presented with this nifty options dialog:

CompressionChoose from the available compression methods. For more information, see
OpenEXR Compression.
Luminance/ChromaTranslate RGB into Luminance/Chroma channels and subsample. Only
available for single-layer files. See the Luminance/Chroma section.
32-bit floatBy default, OpenEXR stores pixels in a 16-bit float format. This is usually ideal, but
if you have a need for 32-bit float pixels (perhaps because you have values over 65,504.0?),
check this box. Otherwise it will just increase your file size unnecessarily.

12

Include layer compositeProEXR lets you explicitly say which channels will be saved in the file,
but under this method you will not end up with the standard R, G, B channels unless you
create a layer called RGB. With this box checked, ProEXR will take a snapshot of your
composited layers and use that for the standard RGBA channels that most programs look for
(so its good for compatibilitys sake). In general youll want to leave it on.
Include hidden layersUnless this is checked, hidden layers will be ignored.

About Alphas
If an EXR has an alpha channel (named A), ProEXR will assume that it should be applied to
every layer, burning transparency into all of them. If for some reason you disagree with this behavior, you may change the Import Options. On output, the alpha channel is re-saved.
Heres where it gets tricky: OpenEXR files with alpha channels are stored as premultiplied, while
Photoshop and After Effects uses straight images internally. By default, ProEXR handles all the
conversion back and forth between the two formats. There may be times when you want to overrule ProEXRs alpha conversionfor those times Ill once again point you to our section about
Import Options.
If all this alpha talk is making your head spin, or maybe you cant ever hear enough about alpha
channels (I know I cant), see the section called All About Alphas.

Layer Export
While we all know its great to be able to save all our layers into a single OpenEXR file [insert pat on back here],
the fact is that many programs dont understand such
files (including ummstock Photoshop). To work bet13

ter with such programs, ProEXR has the ability to save out each layer as a separate EXR file. Simply go to File Export ProEXR Layer Export.
Upon selecting this option, you will be asked to enter a file name which will serve as the basis for
the layers to be exported. So if you had layers called sky, buildings, and lights and exported a
base file called painting.exr, your layered files would be called painting_sky.exr,
painting_buildings.exr, and painting_lights.exr.
If you check the box to Include layer composite, a full layered EXR with composited RGB channels will be placed as the base file.

Suggested Workflow
Because there are some items in a Photoshop project that arent supported in an EXR file, we recommend that all Photoshop work be saved as real, honest-to-dog Photoshop files. And then when
its time to export your project to another program using an industry-standard, open-source,
production-tested, layer-friendly, floating point format, well thats where ProEXR comes in.
In some cases, you may have to do a little project clean-up before exporting, merging this, or rasterizing that. In those cases we hope you can find a way to automate the process using the scripting built in to Photoshop. To help you in this endeavor, ProEXR supports the Photoshop Actions
scripting model.

14

Below is a table of some things ProEXR supports and doesnt, and even why:
Photoshop item

Layers
Text Layers

Support?

Yes!
Sort of

eh?

That was the whole point, right?

They get rasterized into pixels.

Adjustment Layers

Not really

They appear in the file, but without an adjustment.

Layer Sets

Not really

The layers do appear, just not in a set.

Transparency

Yes

We like to call it the alpha channel.

Layer Masks

Yes

It gets combined with transparency.

Vector Masks

No

Try a vector format, bub.

Layer order

Yes

Gets stored as a custom attribute read by PS and AE.

Visibility

Yes

Stored in the same custom attribute.

Transfer Mode

Yes

That custom attribute again.

Opacity

Yes

Yeah, custom attribute.

Color Space

Yes

See OpenEXR Color.

Channels Palette

ProEXR: No, only the Layers palette is used.

ProEXR EZ: Yes, can be used for an Alpha (A).

Paths

No

Try EPS.

Layer Styles

No

Ha!

Smart Filters

No

See Layer Styles.

Some other item

15

Not likely

EXR is a bitmap format, man. This aint TIFF.

Import Options
As mentioned before, ProEXR has a certain default
behavior when it comes to alpha channels. While we
at fnord software think were really doing the right
thing there, weve also provided a secret dialog (well,
it was secret) to effect the process. To bring up this
dialog, hold down the Shift key right as an EXR file
begins to open in Photoshop. It lets you control the
following:
Alpha ModeThe default behavior in ProEXR is to
use the Alpha channel(s) to make layers
transparent. You can select an alternate mode where no transparency is used and Alpha
channels are placed on their own layer. (In ProEXR EZ, this option puts the alpha in the
Channels palette.)
UnMultiplyWhen using the second alpha mode, all channels typically appear as they do in the
file: premultiplied. An option is provided to UnMultiply the RGB channels by the alpha. Youll
see straight pixels in all their jaggy glory! Hope you know what youre doing.
Layering AttributeOption to ignore the neat-o custom attribute ProEXR stored to remind
Photoshop what the original layer names and order was. Instead, layers get assembled oldschool. (Not found in ProEXR EZ, which ignores all layers.)
Memory MappingReads the entire binary EXR into memory with one big read operation
before unpacking into Photoshop. Can improve read times for files read over a network, but
will use up more memory.

16

Always Use DialogIf you want to be bugged for import options every time, you can tell the
dialog to always come up. Otherwise you will need to use the Shift key.
Every time an EXR is opened, the default settings will be reloaded, regardless of what was used
used for the previous file. Use the Set Defaults button to customize those settings.

Channel Info
Photoshop and OpenEXR have different notions of how to store layers, and getting them to sync
up isnt always easy. Photoshop thinks of each layer as a group of 4 RGBA channels with a layer
name that isnt necessarily unique. Layers also have a stacking order, transfer modes, layer masks,
opacity, etc.
OpenEXR, on the other hand, only has a list of channels, each with a unique name. A weaklyenforced layering method has been created through a naming convention: if you have a layer
named reflection and it has three RGB channels, what you actually have in the EXR are three
channels called reflection.R, reflection.G, and reflection.B. You might not have any
reflection.A, and in some cases you may have fewer channels with different names such as
velocity.X and velocity.Y.
The goal with ProEXR was to retain all the original channel information so that you could open an
EXR, make some changes, and the save it with the same channels it originally came in with. So in
order to remember what the original channels were, we format the layer names in a special way.
Dont be afraid to ignore these formatting rulesProEXR will just assume you want all 4 RGBA
channels in that case. But if you want more control, follow the examples below:

17

Photoshop layer name

OpenEXR channels

spaceship

spaceship.R, spaceship.G, spaceship.B, spaceship.A

dinosaur.RGBA

dinosaur.R, dinosaur.G, dinosaur.B, dinosaur.A

alien.RGB

alien.R, alien.G, alien.B

alien.[R][G][B]

alien.R, alien.G, alien.B

velocity.XY

velocity.XY.R, velocity.XY.G, velocity.XY.B, velocity.XY.A

velocity.[X][Y]

velocity.X, velocity.Y

depth.[Z]

depth.Z

normals.[NX][NY][NZ]

normals.NX, normals.NY, normals.NZ

texture.[U][V][A]

texture.U, texture.V, texture.A

[Transparency]

Transparency (an EXR channel without any layer association)

Specular

Specular.R, Specular.G, Specular.B, Specular.A

RGB

R, G, B (RGB and RGBA are special names that dont become RGB.R, RGB.G, etc)

RGBA

R, G, B, A

In general, channels are retrieved from Photoshop in RGBA order. The exception is that any
channel.[A] will get the alpha channel. So in the texture.[U][V][A] example, red is texture.U,
green is texture.V, and alpha (not blue) is texture.A. Brackets can be used to collect one word into
a channel name, so the Transparency channel will live alone and come from that layers red
channel.
If you have duplicate layer names, ProEXR will increment the name to prevent duplicate channel
names in the EXR, which arent allowed.
18

Note that some programs do not support EXR files with channel names over 32 characters, even
though the OpenEXR format now supports up to 255. If you are worried about compatibility,
keep you channel names short.
Finally, ProEXR saves a custom chunk of data with the file so that if you re-open a layered file, the
layers will appear as you originally labeled them, not with the layer formatting. (You can use import options to ignore this data and force the layer formatting if you like.) This data can also be
used in Nuke 6.3 and later to build a comp automatically using the included Python script
ProEXR_Comp_Builder.py.

File Description
While ProEXR exposes all floating point channels to Photoshop, an EXR file may have any number of attributes that generally remain unseen. A complete report of all components in the file is
inserted into the Description field in Photoshops File Info window.

19

ProEXR in After Effects

Caveat
OK, actually many of the After Effects plug-ins arent really considered part of the commercial ProEXR package. For
one thing, theyre free, open source, and even ship in After Effects (CS4 and later). But since they were written in parallel with the Photoshop plug-in and share so much with it, it seemed silly to put them in a separate manual.

OpenEXR file module

Reading
OpenEXR files appear as floating point, premultiplied image files. A standard EXR file contains
channels R, G, B, plus alpha channel A, and these are the channels you initially see when using the footage.

Any extra channels in an EXR file can be accessed with 3D Channel plug-ins, some of which are
included with this package and described below.
If you have an EXR with many channels, you may want to turn
on the option to Cache Channels, found in the input options
dialog (click the More Options button in AEs Interpret Footage
dialog). With this option enabled, all the channels in the file
will be read at once and stored in a memory cache. Subsequent
accesses of that file (such as when 3D channels are extracted)
will pull from the cache, avoiding the need to read the file again.
The Cache Size preference determined how many different files
will be stored in memory at once. For maximum speed, this
20

number should be at least as big as the number of cached EXR files that you have on any given
frame in your comp. The cache size setting is set at the machine level, so you may have to change
this setting for different projects and propagate it to different machines you use.
Writing
OpenEXR files are written using the same standard RGBA channels. Clicking the Format Options
button takes you to this pretty dialog:

CompressionChoose from the available compression methods. For more information, see
OpenEXR Compression.
Luminance/ChromaTranslate RGB Channels into Luminance/Chroma channels and
subsample. For more information, see Luminance/Chroma.
32-bit floatBy default, OpenEXR stores pixels in a 16-bit float format. This is usually ideal, but
if you have a need for 32-bit float pixels (perhaps because you have values over 65,504.0?),
check this box. Otherwise it will just increase your file size unnecessarily, which is why its not
recommended. 32-bit is not available in conjunction with Luminance/Chroma.
21

Channel Mapping
While the ProEXR package comes with tools to easily extract any channel from a piece of footage,
some plug-ins rely on channels being categorized. To play nice with these plug-ins, there is a editable text file that accompanies the OpenEXR reader called OpenEXR_channel_map.txt. Instructions for use are found in the file itself.
Metadata
The file module will store some extra metadata in each EXR you render. Standard EXR attributes
saved include time of saving, frames per second, and chromaticity. In addition, the names of the
After Effects project and comp used to create the file are stored.
Secret Preferences
If you open the After Effects Preferences file in a text editor, you can find a section that looks like
this:
["OpenEXR"]
"Memory Map" = "0"
"Store Machine Info" = "0"
"Store Personal Info" = "0"
"Channel Cache Expiration" = "30"

(etc)

You can change the 0 to a 1 for a property and save the file (make sure AE is not running) to enable the following options:
Memory MapThe EXR file will be completely copied into a memory buffer with one read
operation and then decompressed form there. This can lead to speed improvements,
particularly when files are accessed via a network. It will also use up more memory, however.
Store Machine InfoTags each EXR with the computers network name. Can be useful for
tracking down the render node that created a problematic file.
22

Store Personal InfoTags each EXR with the users name.

Channel Cache ExpirationThe length of time in seconds before an un-accessed EXR cache
will automatically free itself from memory.
Auto Cache ThresholdIf a file has at least this number of channels, Channel Caching will be
turned on automatically for you. Setting it to 0 means it will not be turned on automatically.
Enable displayWindow DialogMakes it possible to choose between a files displayWindow and
dataWindow. For more information on this feature, see this blog post.

EXtractoR
Whereas most 3D Channel plug-ins are limited to a certain
set of pre-defined channels, EXtractoR will open any channels available so long as theyre floating point. The extracted
channel names are listed in the Channel Info pane. As with all
3D Channel plug-ins, you must apply EXtractoR directly to
the footage layer, not to a pre-comp.
When you click on said Channel Info pane, a dialog will pop
up allowing you to pick from menus that reflect channels present in the current image. You may also choose to simply copy
a channel from the input.

23

The Black Point and White Point controls are provided to re-scale the floating point values. At
their defaults, no re-scaling will take place. If a project is in floating point mode, the user may
mouse over the image and see the raw values in the Info Panel.
Channel values will depend on the renderer. Z-depth values are
often negative, which might call for setting the White Point to a
negative number, perhaps a large one. Velocity channels can be
positive or negative, but usually should be scaled to 0-1 range
with 0.5 meaning no movement. This can be done by setting
the white and black points to opposite values like 50 and -50.
Most 3D renderers output images premultiplied, while AE holds them as straight internally. If you
are bringing in premultiplied RGB channels, you probably want to click the UnMult checkbox.
More detail on this exciting topic available in the All About Alphas section.
A note about color management
The extraction plug-ins take floating point data from an EXR file and put it right into AEs pixel
buffer. As a result, the pixels are simply assumed to be in your projects working space, although
that may not be true. After Effects tags incoming floating point files as being in linear sRGB color
space or applies color space information if it is available in the EXR. Usually this is all taken care
of automatically on the file import end, but EXtractoR is circumventing that step.

To use color management with extracted images, apply the Color Profile Converter, select sRGB
as the input profile (or another color space if you have one), and check Linearize Input Profile.
Keep the project working space as your output profile, and now the layer is once again color managed.

24

Non-image data channels such as Z-depth and Velocity dont have any notion of color space, so
youll usually want to leave them unmanaged.
Note that the importer will tell AE about any color information found in the EXR, but the resulting profile will not be available in the Color Profile Converter. Sounds like an Adobe feature request to me.

IDentifier
Whereas EXtractoR pulls floating point channels out of an
EXR file, this plug-in gets the non-image channels such as
Object and Material ID. It uses a dialog similar to EXtractoR's.
The default "Colors" display is meant to provide an easy preview, showing that the ID channel has been found and that
objects in the scene have different IDs. The Luma and Alpha
matte options are what you will probably end up using in a
comp. Raw output (scaled to 8-bit) is also provided if you
want to sample ID numbers with your mouse.

ProEXR AE
As the name suggests, this plug-in is considered part of the non-free portion of ProEXR and does
not ship with After Effects. It is responsible for two separate functions: saving layered EXR files
from an After Effects comp, and building AE comps from a layered EXR file.

25

Building Comps
Select an EXR file in the Project pane and select Create
ProEXR Layer Comps from the File menu. ProEXR will
create source comps for each layer in the file, apply the appropriate extraction plug-in, and add each source comp to
an assemble comp. Files originally created with ProEXR will retain layer ordering, transfer mode,
etc. through a custom attribute saved in the file. Not bad!

For times when you need extra control over the set-up of source comps, you can get things started
by dropping the EXR into a new comp and positioning it as you like. Then select the layer, apply
the menu command, and all the source comps will match your original comp, which then becomes the assemble comp.
Saving Layered EXR Files
With the plug-in installed, you will find ProEXR as an additional option under Composition
Save Frame As. This will write out layered EXRs from your After Effects comp using the same
naming convention described in the Channel Info section above.

If you are using After Effects CC 2014 and earlier, you also have the option to choose ProEXR
Layers Sequence as a format in AEs output module, and this is in fact the preferred method.
This plug-in has to do a few backflips to convert your layered comp to a single EXR. You can help
it out by using plain layer names and simple transfer modes.
Note that the layers in this file do not flow through the standard AE output module, so no color
transformations are applied. Working in a linear color space will help ensure your files are kosher.
Unlike the regular OpenEXR file module, ProEXR AE will include timecode in the files it saves. If
you would like to create standard RGBA files with timecode, create a render comp with only a sin26

gle layer called RGBA (RGB if you dont want an alpha) and turn off Include Layer Composite in the format options dialog. The Comp Creator will read timecode and use it when setting up
your project.

27

OpenEXR in Premiere Pro

Nota bene
As of the November 2015 update, this plug-in comes installed with Premiere CC. A copy of the plug-in is included with
ProEXR, allowing users of earlier Premiere versions to add OpenEXR support for free.

Overview
The OpenEXR plug-in for Premiere Pro lets you import and export OpenEXR sequences as you
would the natively supported image sequences such as PNG and TIFF. Premiere actually supports
linear floating point image buffers natively, so that is how EXRs are presented, with Premiere responsible for any conversion to and from the more common video color spaces. Timecode is supported on both input and output.
Reading
A standard OpenEXR file has channels R, G, B, and possibly A for an alpha channel. These
are the channels the plug-in will generally look for when reading into Premiere. If you have extra
channels in your file, you may access them via a dialog found using Clip > Source Settings.
Bypass linear conversion
Both the Source Settings dialog and the export settings include an option to bypass linear conversion. OpenEXR files are usually in linear space, and that is how they are presented to Premiere.
Premiere usually works in video space, converting back and forth from linear using a 0.45 gamma.
In some cases, you may wish to skip the conversion, possibly to handle it manually. With this option checked, the plug-in will tell Premiere its pixels are in video space, rather than linear.

28

Writing
ProEXR will appear as a file format option in Premieres Export
Settings dialog. The same compression options provided in the
standard After Effects OpenEXR output module are provided in
ProEXR for Premiere.

Unlike After Effects, Premieres image size and frame rate options
may not always match the settings for your edit sequence, so make
sure you verify them. Also double-check the Render to Sequence option, which is off by default. It is recommended that
you create your own output presets for use with ProEXR.

29

General OpenEXR Info

About OpenEXR
In recent years as computing power has continued to increase, most everyone working at the
bleeding edge of computer graphics is working in floating point. And that means a floating point
format is needed. And the format of choice is OpenEXR, created by some folks known to trip
right over the bleeding edgeIndustrial Light and Magic.
OpenEXRs predecessors were never ideally suited for the job. Formats like floating point TIFF
and Radiance were either inefficient with their storage of floating point data, limited from a production standpoint, or both. ILM needed a format to suit their needs, so they went out and created one. Then they released the code for it as open source.
The OpenEXR format is very flexible. It can hold any user-defined attributes in addition to a set
of standard ones. An EXR can hold any number of channels, each identified by an arbitrary name,
although I should mention that since many programs only seek out the following sets of reserved
channels, so its always good to have them present to insure maximum compatibility:
RGB

Grayscale

Luminance/Chroma

Alpha channel

Z-Depth

R G B

Y RY BY

Z (unofficial)

OpenEXR images are always floating point. But because full 32-bit floating point image data tends
to be unwieldy and compresses poorly, OpenEXR uses a 16-bit (Half ) floating point format that
matches what is found in some modern graphics cards. For digital images which generally have
30

some degree of noise or sampling error, the extra precision from a 32-bit float file is really meaningless. Of course, OpenEXR does support full 32-bit float if you need it, as well as integer pixels
for non-image data like Object ID.
To store pixel data more effectively, OpenEXR utilizes image compression, typically lossless to
avoid any kind of image degradation, yet still provide a significant reduction in file size. When image fidelity is less crucial, lossy compression and chroma subsampling are available to further
crush file sizes.
So all in all, OpenEXR is a pretty amazing format. Lets give a shout-out to the ILM authors who
made it for us, shall we?

Florian Kainz
Rod Bogart
Drew Hess
Paul Schneider
Bill Anderson
Wojciech Jarosz
Andrew Kunz
Piotr Stanczyk
Peter Hillman
Thanks guys!
For more information on OpenEXR, visit the official site:
http://www.openexr.com/

31

OpenEXR Compression
OpenEXR supports a variety of compression methods, described in the table below:
None

No compression, but reads quickly.

RLE

Run Length Encoding. Still reads fast, but somewhat smaller.

Zip

Compresses each line with Zip. Slow compression, but faster decompression.

Zip16

Zip 16 lines together. Particularly ideal for CG renders, textures.

Piz

Wavelet encoded, then Zipped. Best for photographic HDRs.

PXR24

Use with 32-bit float. Rounds to 24-bit for better compression.

B44

Good lossy compression, squeezing channels to 44% their original size.

B44A

Same as B44, but with extra compression on areas with flat color.

DWAA

Lossy compression from DreamWorks Animation. Fast and high quality.

DWAB

DWAB compresses 256 scanlines at a time, vs. DWAA which does 32.

The first five compression methods are lossless. PXR24 is lossless after it removes 8 bits of floating point precision. The last four compression methods are lossy.
Compression performance depends on the image content. For images with a lot of continuous
color (such as motion graphics or CG renders), Zip16 is almost always the best-performing
method, beating even B44 in both file size and speed. B44A was created for lossy compression of
such images.

32

For photographic HDR images (especially with film grain), 16-bit Piz usually gives the best combination of image fidelity and file size. If you are less concerned about fully lossless compression,
Luminance/Chroma sampling and B44A compression will make a much smaller file.
For example, I created a 32-bit HDR photograph in Photoshop and saved it using various file formats and settings. In descending order of size they were:
File

Settings

Size

TIFF

32bpc

3.9 MB

Photoshop (PSD)

32bpc

3.9 MB

OpenEXR

32bpc, None

3.9 MB

OpenEXR

32bpc, Piz

3.7 MB

OpenEXR

32bpc, PXR24

2.1 MB

OpenEXR

16bpc, None

2.0 MB

OpenEXR

16bpc, RLE

1.7 MB

OpenEXR

16bpc, Zip

1.4 MB

OpenEXR

16bpc, Zip16

1.3 MB

OpenEXR

16bpc, Piz

1.3 MB

OpenEXR

16bpc, B44, L/C

443 K

The first two EXR formats held the original 32-bit float pixels without any change at all. Using
PXR24 compression and then 16bpc pixels results in progressively more loss, but the changes are
mostly academic, resulting in no loss that could possibly be detected visually. While B44 compres-

33

sion and Luminance/Chroma sampling made significant changes to pixel values, the image still
had no visual artifacts, and slight differences were only detectable in areas of high contrast and
saturation. (Note that Luminance/Chroma may not be supported by all readers.)

Luminance/Chroma
In any level of graphics production, its never desirable to use formats such as JPEG that will degrade the quality of the image youre working on. However, such formats are valuable at the final
delivery stage where they can dramatically shrink file size without compromising too much image
fidelity, but fidelity should always be maintained in production.
OpenEXR was created for a production environment, so image fidelity was always a top consideration. Like TIFF and PNG, OpenEXR files are generally saved losslessly, even if the the image
data is compressed within the file. No pixels are harmed.
But now OpenEXR has added some lossy compression features to emulate JPEG compression in
floating point. The first feature is the B44 (and B44A) compression mentioned above. B44 is similar to the lossy DCT compression used in JPEG for compressing blocks of pixels.
The second feature, also found in JPEG, is the
breaking down of standard RGB channels into Luminance and Chroma channels (Y, RY, and
BY), and then shrinking (subsampling) the colordifference channels separately.
Because the RY and BY channels contain the number of pixels, the overall file data is reduced
by . And yet, in most cases there is no visual difference due to human perception being more
sensitive to slight changes in brightness and less to slight changes in color. Combine Luminance/

34

Chroma sampling with B44A compression and you have an ideal way to save bandwidth when
sending EXR files through email.

Linear color space

Most floating point formats, including OpenEXR, assume that pixels are stored in a linear color
space. This means that pixel values displayed directly on a monitor will appear unusually dark because your display is non-linear (it has a gamma of 2.2 or so) and is darkening the image. Other
formats such as JPEG store pixels brightened up to compensate for this darkening (using the inverse gamma), which is why they appear normal.
The reason linear color space is important is because that is the color space of the real world.
Gamma encoding is something made up for use by computers and their 8-bit displays. By performing all your image transformations in linear color space, you are therefore better simulating
real light. Many happy accidents are the result, such as blurry highlights spreading out more realistically and blowing through a motion blurred object in the foreground.
Visual effects are generally trying to simulate happenings in the real world. That, and the need to
represent overbright (> 1.0) pixel values, is why ILM created OpenEXR as a linear floating point
format.
However, some operations are in fact not trying to simulate natural phenomena. One good example is the adding of grain, which in the real world happens on a piece of film or in a cameras
CCDon the encoding end. To simulate the adding of grain, you should convert the image to the
appropriate color space (such as Cineon Log), add the grain, and then convert back.

35

You'll find that by using color space to your advantage and performing operations the right way,
your work will tend to elevate and your process will make sense.
All 32-bit Photoshop documents are automatically assigned a linear color space. In After Effects,
enter the Project Settings, choose a Working Space profile, and check Linearize Working Space
to composite in linear. And of course, always set your AE project depth to 32-bit float.

OpenEXR color information

All Adobe color management is done using ICC Profiles. Profiles define the color space for a
documentthe mapping of RGB pixel values in the computer to their actual appearance when
viewed on a particular device. The idea is that if we know the color space a file was created with
and also know the color space our new device, color management software can tweak values so
that the actual appearance is the same on both. Well, thats the theory.
ICC profiles typically define the RGB color primaries and then provide a gamma-ish response curve. Since OpenEXR files are always
defined to use a linear response curve, a full ICC Profile was not
deemed necessary and instead the RGB primaries are defined using
chromaticity, which is then stored in the EXR.
You may recognize the diagram to the rightits a chromaticity diagram. Chromaticity for a color is specified with a pair of coordinates
(x, y) on this graph. As the name implies, chromaticity only contains
information about color without containing any information about
brightness. The colored area of the graph represents all the colors that a human can see.

36

A complete description of a linear color space can be made by providing (x, y) color coordinates
for each of the three RGB tristimuli, along with the white point coordinates (the D65 dot in the
diagram).
To pass color space information to the Adobe apps, ProEXR converts between the ICC Profiles
from the host and Chromaticity settings in the EXR. A custom attribute is also saved to remember
the color spaces name as well as a copy of the original ICC profile for programs that support
them.

OpenEXR support in other apps

Wondering who you might exchange these fancy EXR files with? Wonder no more
Application

OpenEXR support

Maya

Basic support with included Mental Ray renderer. 3Delight, Renderman, V-Ray, other renderers also support multi-channel OpenEXR.

3DS Max

As of 3DS Max 2011, full support.

Lightwave

Full multi-channel output support using exrTrader, www.exrtrader.com.

Softimage

Multiple channel support possible using Mental Ray shaders.

Cinema 4D

Basic RGBA support.

Houdini

Full support for piping arbitrary data to EXR channels.

Shake

Full access to all channels from the FileIn node.

Fusion

Good multi-channel input and pipeline support.

Nuke

Full support for multiple channels through the entire pipeline.

37

All About Alphas

Transparency in an image is indicated through the use of an alpha channel. A 3D renderer will include an alpha and transparent parts of a Photoshop layer (made with the eraser, a layer mask, or
other means) become the alpha channel.
When an alpha channel is present, the RGB channels can be in one of two forms: premultiplied
or straight. The difference between the two is seen in translucent areas of the image, such as the
motion blurred edges in the sample below. Fully opaque and fully transparent areas are not effected by this.
The edge of the CG object in the image below is white, but the pixels have been made translucent
by motion blur, so they mix with the black background and become grey. In a straight image, this
original state is rememberedthe white pixels on the edge stay white until the end of the object
and it is left for the alpha channel to provide a soft edge. In the premultiplied image you see the
result of the alpha getting appliedthe edge appears soft as it has already been composited over
black. It turns out that this operation is a multiplication of the straight RGB with the alpha, hence
the image is pre-multiplied.

38

Premultiplied

Straight

Alpha

In general, it doesnt matter which type of image is being stored because each one can be converted into the other. But it is important that the programs you use receive the type of image they
expect.
If they make an assumption, most programs today assume a premultiplied
image is being used. Conveniently, the OpenEXR spec specifically specifies premultiplied images. 3D renderers usually create premultiplied images and most compositing programs expect themexcept for the Adobe
programs. Both Photoshop and After Effects use straight pixels internally,
so ProEXR must un-multiply (UnMult) the RGB channels to create a
transparent layer. In After Effects, you can view raw straight pixels using
the channel view pulldown. These straight pixels should look jagged around
the edgesif they dont, maybe you forgot to interpret them premultiplied or click UnMult in
EXtractoR.

39

On the way out, ProEXR premultiplies layers in Photoshop before saving them in the EXR. In After Effects, the user should leave the color premultiplied in the output module.
There may be times in Photoshop where you dont want ProEXR to UnMult
the RGB channels or when you want to use them without the alpha being applied to the layer. See the Import Options section for information on how to
do that.
One specific case of alpha manipulation appears when you want to use multiple render passes to make a composite in Photoshop. To do this correctly, you
must load the EXR with channels UnMulted. Then create a layer mask on
your bottom layer and copy the alpha channel into it. From there, other layers
can be dropped on top of the base layer and then grouped by option-clicking
on the lines between them in the layers palette. Only when your channels are
straight and the layers are grouped together will the edges merge together properly in Photoshop.
It aint pretty, I know.
I should mention one more thing: when you copy the alpha channel into the layer mask, Photoshop will
think its doing you a big favor by converting it from linear space to perceptual space, therefore brightening it up. For best results, counteract this move by applying a Levels call to the layer mask with a gamma
of 0.4545.

Version History
1.0August 20, 2007Initial release using OpenEXR version 1.6.0
1.1September 6, 2007Added File Info description, enhanced Comp Creator
1.2October 23, 2007Writing additional metadata, some bug fixes
1.3September 12, 2008Import options dialog in Photoshop
1.5February 13, 2010Complete re-write and addition of ProEXR EZ

40

1.6October 27, 2011ProEXR AE, memory mapping

1.7April 26, 2012ProEXR for Premiere, speed optimizations, ProEXR EZ now free
1.8April 4, 2013Channel Caching in AE, UTF-8 support
1.9June 18, 2014OpenEXR 2 support, displayWindow handling, EXtractoR layer pulldown
1.9.1February 25, 2016After Effects Save Frame As command added

41

Copyright Notices
All ILM wants me to do in return for using their free OpenEXR library is print this message:
Copyright 2006, Industrial Light & Magic, a division of Lucasfilm Entertainment
Company Ltd. Portions contributed and copyright held by others as indicated. All
rights reserved.
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation and/
or other materials provided with the distribution.
Neither the name of Industrial Light & Magic nor the names of any other
contributors to this software may be used to endorse or promote products
derived from this software without specific prior written permission.
This software is provided by the copyright holders and contributors as is and any
express or implied warranties, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose are disclaimed. In no event shall
the copyright owner or contributors be liable for any direct, indirect, incidental,
special, exemplary, or consequential damages (including, but not limited to,
procurement of substitute goods or services; loss of use, data, or profits; or business
interruption) however caused and on any theory of liability, whether in contract,
strict liability, or tort (including negligence or otherwise) arising in any way out of the
use of this software, even if advised of the possibility of such damage.

42

ProEXR also uses Little CMS, with this copyright notice:

Little Color Management System
Copyright 1998-2012 Marti Maria Saguer
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify,
merge, publish, distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to the following
conditions:
The above copyright notice and this permission notice shall be included in all copies
or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF
CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
DEALINGS IN THE SOFTWARE.

And lets not forget zlib:

Copyright 1995-2013 Jean-loup Gailly and Mark Adler
This software is provided 'as-is', without any express or implied warranty. In no event
will the authors be held liable for any damages arising from the use of this software.

43

Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
1.The origin of this software must not be misrepresented; you must not
claim that you wrote the original software. If you use this software in a
product, an acknowledgment in the product documentation would be
appreciated but is not required.
2.Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
3.This notice may not be removed or altered from any source distribution.

Fin

44