FORCES ACTING ON A DAM STRUCTURE

In the design of a dam, the first step is the determination of various forces which acts on
the structure and study their nature. Depending upon the situation, the dam is subjected to
the following forces:
1.
2.
3.
4.
5.
6.

Water pressure
Earthquake forces
Silt pressure
Wave pressure
Ice pressure
Self weight of the dam.

The forces are considered to act per unit length of the dam.
For perfect and most accurate design, the effect of all the forces should be investigated. Out
of these forces, most common and important forces are water pressure and self weight of
the dam.
1. Water Pressure
Water pressure may be subdivided into the following two categories:
I) External water pressure:
It is the pressure of water on the upstream face of the dam. In this, there are two cases:
(i) Upstream face of the dam is vertical and there is no water on the downstream side of the
dam (figure 1).

Figure 1

The total pressure is in horizontal direction and acts on the upstream face at a height
from the bottom. The pressure diagram is triangular and the total pressure is given by

Where w is the specific weight of water. Usually it is taken as unity.

H is the height upto which water is stored in m.
(ii) Upstream face with batter and there is no water on the downstream side (figure 2).

Figure 2
Here in addition to the horizontal water pressure
as in the previous case, there is vertical
pressure of the water. It is due to the water column resting on the upstream sloping side.
The vertical pressure
given by

acts on the length b portion of the base. This vertical pressure is

Pressure
acts through the centre of gravity of the water column resting on the sloping
upstream face.

If there is water standing on the downstream side of the dam, pressure may be calculated
similarly. The water pressure on the downstream face actually stabilizes the dam. Hence as
an additional factor of safety, it may be neglected.
II) Water pressure below the base of the dam or Uplift pressure
When the water is stored on the upstream side of a dam there exists a head of water equal
to the height upto which the water is stored. This water enters the pores and fissures of the
foundation material under pressure. It also enters the joint between the dam and the
foundation at the base and the pores of the dam itself. This water then seeps through and
tries to emerge out on the downstream end. The seeping water creates hydraulic gradient
between the upstream and downstream side of the dam. This hydraulic gradient causes
vertical upward pressure. The upward pressure is known as uplift. Uplift reduces the
effective weight of the structure and consequently the restoring force is reduced. It is
essential to study the nature of uplift and also some methods will have to be devised to
reduce the uplift pressure value.

Figure 3
With reference to figure 3, uplift pressure is given by

Where
is the uplift pressure, B is the base width of the dam and H is the height upto
which water is stored.

This total uplift acts at

from the heel or upstream end of the dam.

Uplift is generally reduced by providing drainage pipes or holes in the dam section.
Self weight of the dam is the only largest force which stabilizes the structure. The total
weight of the dam is supposed to act through the centre of gravity of the dam section in
vertically downward direction. Naturally when specific weight of the material of construction
is high, restoring force will be more. Construction material is so chosen that the density of
the material is about 2.045 gram per cubic meter.
2. Earthquake Forces
The effect of earthquake is equivalent to an acceleration to the foundation of the dam in the
direction in which the wave is travelling at the moment. Earthquake wave may move in any
direction and for design purposes, it is resolved into the vertical and horizontal directions.
On an average, a value of 0.1 to 0.15g (where g = acceleration due to gravity) is generally
sufficient for high dams in seismic zones. In extremely seismic regions and in conservative
designs, even a value of 0.3g may sometimes by adopted.
Vertical acceleration reduces the unit weight of the dam material and that of water is to
times the original unit weight, where
is the value of g accounted against
earthquake forces, i.e. 0.1 when 0.1g is accounted for earthquake forces. The horizontal
acceleration acting towards the reservoir causes a momentary increase in water pressure
and the foundation and dam accelerate towards the reservoir and the water resists the
movement owing to its inertia. The extra pressure exerted by this process is known as
hydrodynamic pressure.
3. Silt Pressure
If h is the height of silt deposited, then the forces exerted by this silt in addition to the
external water pressure, can be represented by Rankine formula

acting at

from the base.

Where,

= coefficient of active earth pressure of silt =

= angle of internal friction of soil, cohesion neglected.
= submerged unit weight of silt material.
h = height of silt deposited.
4. Wave Pressure

Waves are generated on the surface of the reservoir by the blowing winds, which exert a
pressure on the downstream side. Wave pressure depends upon wave height which is given
by the equation
for F < 32 km, and
for F > 32 km
Where

is the height of water from the top of crest to bottom of trough in meters.

V wind velocity in km/hour

F fetch or straight length of water expanse in km.
The maximum pressure intensity due to wave action may be given by

and acts at

meters above the still water surface.

Figure 4

The pressure distribution may be assumed to be triangular of height

4.
Hence total force due to wave action

=
5. Ice Pressure

acting at

above the reservoir surface.

as shown in figure

The ice which may be formed on the water surface of the reservoir in cold countries may
sometimes melt and expand. The dam face is subjected to the thrust and exerted by the
expanding ice. This force acts linearly along the length of the dam and at the reservoir level.
The magnitude of this force varies from 250 to 1500 kN/sq.m depending upon the
temperature variations. On an average, a value of 500 kN/sq.m may be taken under
ordinary circumstances.
6. Weight of dam

The weight of dam and its foundation is a major resisting force. In two dimensional analysis
of dam, unit length is considered.

ENERGY LOSSES IN PIPE FLOW

Theory
When a fluid is flowing through a pipe, the fluid experiences some resistance due to which
some of the energy of the fluid is lost. This loss of energy is classified as:
1. MAJOR ENERGY LOSSES:
The viscosity causes loss of energy in the flows, which is known as frictional loss or major
energy loss and it is calculated by the following formula;
(a)Darcy-weisbach formula
The loss of head can be measured by the following equations
hf =4f L V2 / (2gD)
Where

hf = Loss of head due to friction

f

= Co-efficient of friction which is a function of Reynolds number

f = 64/Re

(for Re <2000) (laminar flow)

L = Length of pipe
V = mean velocity of flow
D = Diameter of pipe

2. MINOR ENERGY LOSSES:

The loss of energy due to change of velocity of the flowing fluid in magnitude or direction is
called minor loss of energy. The minor loss of energy includes the following cases
(A) Sudden Expansion Of Pipe:

The head loss due to sudden expansion equation is

he = (V1 -V2)2 /2g
Where V1 is the velocity at section 1
V2 is the velocity at section 2
(B)Sudden Contraction Of Pipe:
The head loss due to sudden contraction equation is
hc =k (V22 /2g)
Where

k = ((1/Cc)-1)2
V2 is the velocity at section 2

The value of k is 0.5 to 0.7.

(C) Bending In Pipe:
The head loss due to bending equation is
hb=k (V2 /2g)
Where V is the velocity of the flow.
k is the co-efficient of the bend ,which depends on the angle of the bend, radius of
curvature of bend and diameter of the pipe

CENTROIDS AND CENTRE OF GRAVITY

In general when a rigid body lies in a field of force acts on each particle of the body. We
equivalently represent the system of forces by single force acting at a specific point. This point is
known as centre of gravity. We can extend this concept in many ways and get the various
equivalent parameters of a body, which could help us in dealing the situation directly on a rigid
body rather than considering each individual particle of the rigid body. Various such parameters
include centre of gravity, moment of inertia, centroid , first and second moment of inertias of a
line or a rigid body. These parameters simplify the analysis of structures such as beams. Further
we will also study the surface area or volume of revolution of a line or area respectively.
The centroid (C) is a point which defines the geometric center of an object.

Centroid is a geometrical centre of a plane figure or an object, it divides the shape into regions of
equal moments. whereas the centre of a gravity is the point through which the weight of a body
acts. the term centre of gravity applies to the bodies with mass and weight while the term
centroid applies to plane areas.

Centre of gravity
Centre of gravity of a body is defined as the point through which the whole weight
of the body acts. A body can have only one centre of gravity for all positions of the
body. It is represented or denoted by C.G. or G.

Centroid
The point, at which the total area of a plane figure (such as rectangle, triangle,
square, quadrilateral, circle etc) is assumed to be concentrated, is called the
centroid of that area. The centroid is also represented by C.G. or G.The centroid
and centre of gravity are at the same point.
Centroid or centre of gravity of simple plane figures:

The C.G. of a uniform rod lies at its middle point.

The C.G. of a triangle lies at the point where all the three medians intersect
each other.

The C.G. of a rectangle (or a parallelogram or a square) lies at the point

where its diagonals intersect each other. It is also the point of intersection of
the middle points of the opposite sides.

The C.G. of a circle lies at its centre.

The center of buoyancy of an object is located at the point that would be the center of mass of the
displaced fluid that would occupy the volume that is actually occupied by the buoyed object.
In the same way that gravity can be thought of as pulling on a compact object by acting on its
center of mass, the buoyant force can be thought of as acting on a compact object (a particle) at
that particle's center of buoyancy.
An object whose center of mass is lower than its center of buoyancy will float stably, while an
object whose center of mass is higher than its center of buoyancy will tend to be unstable and
have a tendency to flip over in the fluid that is buoying it up.
The centre of buoyancy is the centre of gravity of the displaced fluid.