Scribd
Upload
382 views

Api 510 2016

An internal inspection of a vessel with acidic corrodents would likely find hydrogen blistering near the liquid level. An external inspection of a pressure vessel should begin by examining the anchor bolts, foundation, and supports. Given pressure readings from gauges located 45 feet and 100 feet from the top of a 125 foot pressure vessel undergoing a hydrostatic test, the pressure at the top would be 189psi. According to API-510, a pressure relief device repair concern must have state certified repair personnel. An owner/user shop would not be an acceptable API-510 repair organization.

Uploaded by

أحمد صبحى
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
382 views

Api 510 2016

An internal inspection of a vessel with acidic corrodents would likely find hydrogen blistering near the liquid level. An external inspection of a pressure vessel should begin by examining the anchor bolts, foundation, and supports. Given pressure readings from gauges located 45 feet and 100 feet from the top of a 125 foot pressure vessel undergoing a hydrostatic test, the pressure at the top would be 189psi. According to API-510, a pressure relief device repair concern must have state certified repair personnel. An owner/user shop would not be an acceptable API-510 repair organization.

Uploaded by

أحمد صبحى
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

1.

In planning for an internal inspection of a vertical vessel that


has acidic corrodents, what type of corrosion would you
expect to find on the vessel shell from inside?

a. Hydrogen blistering near liquid level


b. Hydrogen blistering on top dished head
c. Hydrogen blistering near the bottom of vessel
d. None of above

Where should an external inspection of a pressure vessel begin?


a) Anchor bolts, foundation, and supports
b) Ladders, stairways, platforms, or walkways
c) External paint and insulation
d) Nozzles and manways
A 125 feet high pressure vessel is to be hydrostatically tested. What is the pressure at
the top of the vessel if a pressure of 169.5psig is registered on a gage located 45 feet
from the top and another gage, located 100 feet from the top registers 193.5psig? (1
foot of water = 0.433psi)
a) 204psi
b) 189psi
c) 150psi
d) 140psi
According to API-510, a pressure relief device repair concern must have which of the
following?
a) A quality control system
b) State certified repair personnel
c) A National Board VR Stamp
d) A state approved test facility
Which of the following is not an acceptable API-510 repair organization?
a) ASME S Stamp holder
b) Contractor chosen by the owner/operator
c) ASME U Stamp holder
d) Owner/user shop
106. Above what pressure is a vessel considered to be in the scope of the API-510
Code?
a) 2.5psi
b) 5psi
c) 10psi
d) 15psi

The ability of a metal to absorb energy and deform plastically before fracturing is
known as:
a) ductile-to-brittle transition.
b) plasticity.
c) tensile strength.
d) toughness.
Which of the following is most important to document when performing risk-based
inspection assessments?
a) Deficiencies or recommendations for repair for continued service until repairs are
completed
b) Repairing, altering, and re-rating information
c) Construction and design, along with operating and inspection history
d) All factors contributing to the likelihood and consequences of a failure
Statistical data analysis may not be applicable to vessels with:
a) significant numbers of corrosion monitoring locations (CMLs) that were not
measured.
b) random but significant localized corrosion.
c) variations in general corrosion rates.
d) fewer than 10 years of remaining life.
Which of the following nondestructive examination (NDE) methods is most likely to
detect a Lamination subsurface flaw in a pressure vessel?
a) Ultrasonic
b) Magnetic-particle
c) Dye-penetrant
d) Eddy-current
Materials used for replacement during the repair or alteration of a pressure vessel
should be
identified with markings. Which of the following also requires a material test report?
a) Seamless pipe
b) Welded pipe
c) Forged manway cover
d) Plate
When performing vessel repairs, which of the following does not qualify as an API
510 repair organization?
a) Owner/user shop
b) Contractor chosen by the owner/user
c) ASME U stamp holder
d) ASME S stamp holder
For contact examination, the
temperature differential between the calibration block
and examination surfaces shall be within 25F (14C).

You might also like