show

show
To verify the Multiple Spanning Tree (MST) configuration, use the show command. in MST
configuration submode.
show [current | pending]

Syntax Description

current

(Optional) Displays the current configuration that is used to run MST.

pending

(Optional) Displays the edited configuration that will replace the current configuration.

Defaults

This command has no default settings.

Command Modes

MST configuration submode

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The display output from the show pending command is the edited configuration that will replace the
current configuration if you enter the exit command to exit MST configuration mode.
Entering the show command with no arguments displays the pending configurations.

Examples

This example shows how to display the edited configuration:

Router(config-mst)# show pending
Pending MST configuration
Name
[zorglub]
Version
31415
Instance Vlans Mapped
-------- --------------------------------------------------------------------0
4001-4096
2
1010, 1020, 1030, 1040, 1050, 1060, 1070, 1080, 1090, 1100, 1110
1120
3
1-1009, 1011-1019, 1021-1029, 1031-1039, 1041-1049, 1051-1059
1061-1069, 1071-1079, 1081-1089, 1091-1099, 1101-1109, 1111-1119
1121-4000
-----------------------------------------------------------------------------Router(config-mst)#

This example shows how to display the current configuration:

Router(config-mst)# show current

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-555

show

Current MST configuration

Name []
Revision 0
Instance Vlans mapped
-------- --------------------------------------------------------------------0 1-4094
-------------------------------------------------------------------------------

Related Commands

Command

Description

instance

Maps a VLAN or a set of VLANs to an MST instance.

name (MST configuration submode)

Sets the name of an MST region.

revision

Sets the revision number for the MST configuration.

show spanning-tree mst

Displays the information about the MST protocol.

spanning-tree mst configuration

Enters MST-configuration submode.

Cisco IOS Configuration Fundamentals Command Reference

CF-556

April 2010

show <command> append

show <command> append

To redirect and add the output of any show command to an existing file, use the show command | append
command in privileged EXEC mode.
show command | append url

Syntax Description

command

Any Cisco IOS show command.

| append url

The addition of this syntax redirects the command output to the file location
specified in the Universal Resource Locator (URL). The pipe (|) is required.
The Cisco IOS File System (IFS) uses URLs to specify the location of a file
system, directory, and file. Typical URL elements include:
prefix:[directory/]filename
Prefixes can be local file locations, such as flash: or disk0:. Alternatively,
you can specify network locations using the following syntax:
ftp:[[//[username[:password]@]location]/directory]/filename
tftp:[[//location]/directory]/filename
The rcp: prefix is not supported.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.0(21)S

This command was introduced.

12.2(13)T

This command was integrated into Cisco IOS Release 12.2(13)T.

Usage Guidelines

To display all URL prefixes that are supported for this command, use the show command | append ?
command.
This command adds the show command output to the end of the specified file.

Examples

In the following example, output from the show tech-support command is redirected to an existing file
on Disk 1 with the file-name of showoutput.txt. This output is added at the end of any existing data in
the file.
Router# show tech-support | append disk1:showoutput.txt

Related Commands

Command

Description

show <command> redirect

Redirects the output of any show command to a specified file.

show <command> tee

Copies the show command output to a file while displaying it on the

terminal.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-557

show <command> begin

show <command> begin

To begin the output of any show command from a specified string, use the show command | begin
command in EXEC mode.
show command | begin regular-expression

Syntax Description

command

Any supported show command.

A vertical bar (the pipe symbol) indicates that an output processing

specification follows.

regular-expression

Any regular expression found in show command output. The show output
will begin from the first instance of this string (output prior to this string
will not be printed to the screen). The string is case-sensitive. Use
parenthesis to indicate a literal use of spaces.

Specifies a search at a --More-- prompt that begins unfiltered output with

the first line that contains the regular expression.

Specifies a filter at a --More-- prompt that only displays output lines that
do not contain the regular expression.

Specifies a filter at a --More-- prompt that only displays output lines that
contain the regular expression.

Command Modes

EXEC

Command History

Release

Usage Guidelines

Modification

8.3

The show command was introduced.

12.0(1)T

This extension of the show command was introduced..

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

The regular-expression argument is case sensitive and allows for complex matching requirements. Use
parenthesis to indicate a literal use of spaces. For example, | begin u indicates that the show output
should begin with any line that contains a u; | begin ( u) indicates that the show output should begin with
any line that contains a space and a u together (line has a word that begins with a lowercase u).
To search the remaining output of the show command, use the following command at the --More-prompt:
/regular-expression
You can specify a filtered search at any --More-- prompt. To filter the remaining output of the show
command, use one of the following commands at the --More-- prompt:
-regular-expression
+regular-expression
When output volume is large, the search can produce long lists of output. To interrupt the output, press
Ctrl-^ (Ctrl-Shift-6) or Ctrl-z.

Cisco IOS Configuration Fundamentals Command Reference

CF-558

April 2010

show <command> begin

Note

Once you specify a filter for a show command, you cannot specify another filter at the next --More-prompt. The first specified filter remains until the more command output finishes or until you interrupt
the output. The use of the keyword begin does not constitute a filter.
Because prior output is not saved, you cannot search or filter backward through prior output.

Note

Examples

A few show commands that have long output requirements do not require user input at the --More-prompt to jump to the next table of output; these types of output require you to enter the same number
of Ctrl-^ or Ctrl-Z combinations as there are --More-- prompts to completely abort output.

The following is partial sample output of the show interface | begin command that begins unfiltered
output with the first line that contains the regular expression Ethernet. At the --More-- prompt, the user
specifies a filter to show only the lines in the remaining output that contain the regular expression
Serial.
Router# show interface | begin Ethernet
Ethernet0 is up, line protocol is up
Hardware is Lance, address is 0060.837c.6399 (bia 0060.837c.6399)
Description: ip address is 172.1.2.14 255.255.255.0
Internet address is 172.1.2.14/24
.
.
.
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
--More-+Serial
filtering...
Serial1 is up, line protocol is up
Serial2 is up, line protocol is up
Serial3 is up, line protocol is down
Serial4 is down, line protocol is down
Serial5 is up, line protocol is up
Serial6 is up, line protocol is up
Serial7 is up, line protocol is up

Related Commands

Command

Description

more <url> begin

Begins unfiltered output of the more command with the first line that
contains the regular expression you specify.

more <url> exclude

Filters more command output so that it excludes lines that contain a

particular regular expression.

more <url> include

Filters more command output so that it displays only lines that contain
a particular regular expression.

show <command> exclude Filters show command output so that it excludes lines that contain a
particular regular expression.
show <command> include Filters show command output so that it displays only lines that contain
a particular regular expression.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-559

show <command> exclude

show <command> exclude

To filter show command output so that it excludes lines that contain a particular regular expression, use
the show command | exclude command in EXEC mode.
show command | exclude regular-expression

Syntax Description

command

Any supported show command.

A vertical bar (the pipe symbol) indicates that an output processing

specification follows.

regular-expression

Any regular expression found in show command output.

Specifies a search at a --More-- prompt that begins unfiltered output with

the first line that contains the regular expression.

Command Modes

EXEC

Command History

Release

Modification

12.0(1)T

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The regular-expression argument is case sensitive and allows for complex matching requirements.
You can specify a new search at every --More-- prompt. To search the remaining output of the show
command, use the following syntax at the --More-- prompt:
/regular-expression
When output volume is large, the search can produce long lists of output. To interrupt the output, press
Ctrl-^ (Ctrl-Shift-6) or Ctrl-Z.
Because prior output is not saved, you cannot search or filter backward through prior output.

Note

Examples

A few show commands that have long output requirements do not require user input at the --More-prompt to jump to the next table of output; these types of output require you to enter the same number
of Ctrl-^ or Ctrl-Z combinations as there are --More-- prompts to completely abort output.

The following is partial sample output of the show | exclude command used with the show buffers
command. It excludes lines that contain the regular expression 0 misses. At the --More-- prompt, the
user searches for the regular expression Serial0, which continues the filtered output with the first line
that contains Serial0.
Router# show buffers | exclude 0 misses
Buffer elements:
398 in free list (500 max allowed)
Public buffer pools:

Cisco IOS Configuration Fundamentals Command Reference

CF-560

April 2010

show <command> exclude

Small buffers, 104 bytes (total 50, permanent 50):

50 in free list (20 min, 150 max allowed)
551 hits, 3 misses, 0 trims, 0 created
Big buffers, 1524 bytes (total 50, permanent 50):
49 in free list (5 min, 150 max allowed)
Very Big buffers, 4520 bytes (total 10, permanent 10):
.
.
.
Huge buffers, 18024 bytes (total 0 permanent 0):
0 in free list (0 min, 4 max allowed)
--More-/Serial0
filtering...
Serial0 buffers, 1543 bytes (total 64, permanent 64):
16 in free list (0 min, 64 max allowed)
48 hits, 0 fallbacks

Related Commands

Command

Description

more <url> begin

Begins unfiltered output of the more command with the first line that
contains the regular expression you specify.

more <url> exclude

Filters more command output so that it excludes lines that contain a

particular regular expression.

more <url> include

Filters more command output so that it displays only lines that contain
a particular regular expression.

show <command> begin

Searches the output of any show command and displays the output from
the first instance of a specified string.

show <command> include Filters show command output so that it displays only lines that contain
a particular regular expression.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-561

show <command> include

show <command> include

To filter show command output so that it only displays lines that contain a particular regular expression,
use the show command | include command in EXEC mode.
show command | include regular-expression

Syntax Description

command

Any supported show command.

A vertical bar (the pipe symbol) indicates that an output processing

specification follows.

regular-expression

Any regular expression found in show command output. Use parenthesis

to include spaces in the expression.

Specifies a search at a --More-- prompt that begins unfiltered output with

the first line that contains the regular expression.

Command Modes

EXEC

Command History

Release

Modification

12.0(1)T

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The regular-expression argument is case sensitive and allows for complex matching requirements.
You can specify a new search at every --More-- prompt. To search the remaining output of the show
command, use the following syntax at the --More-- prompt:
/regular-expression
When output volume is large, the search can produce long lists of output. To interrupt the output, press
Ctrl-^ (Ctrl-Shift-6) or Ctrl-Z.
Because prior output is not saved, you cannot search or filter backward through prior output.

Note

Examples

A few show commands that have long output requirements do not require user input at the --More-prompt to jump to the next table of output; these types of output require you to enter the same number
of Ctrl-^ or Ctrl-Z combinations as there are --More-- prompts to completely abort output.

The following is partial sample output of the show interface | include command. It displays only lines
that contain the regular expression ( is ). The parentheses force the inclusion of the spaces before and
after is. Use of the parenthesis ensures that only lines containing is with a space both before and
after it will be included in the output. Lines with words like disconnect will be excluded because there
are not spaces around the instance of the string is.
Router# show interface | include ( is )

Cisco IOS Configuration Fundamentals Command Reference

CF-562

April 2010

show <command> include

ATM0 is administratively down, line protocol is down

Hardware is ATMizer BX-50
Dialer1 is up (spoofing), line protocol is up (spoofing)
Hardware is Unknown
DTR is pulsed for 1 seconds on reset
Ethernet0 is up, line protocol is up
Hardware is Lance, address is 0060.837c.6399 (bia 0060.837c.6399)
Internet address is 172.21.53.199/24
Ethernet1 is up, line protocol is up
Hardware is Lance, address is 0060.837c.639c (bia 0060.837c.639c)
Internet address is 5.5.5.99/24
Serial0:0 is down, line protocol is down
Hardware is DSX1
.
.
.
--More--

At the --More-- prompt, the user searches for the regular expression Serial0:13, which continues
filtered output with the first line that contains Serial0:13.
/Serial0:13
filtering...
Serial0:13 is down, line protocol is down
Hardware is DSX1
Internet address is 11.0.0.2/8
0 output errors, 0 collisions, 2 interface resets
Timeslot(s) Used:14, Transmitter delay is 0 flags

Related Commands

Command

Description

more <url> begin

Begins unfiltered output of the more command with the first line that
contains the regular expression you specify.

more <url> exclude

Filters more command output so that it excludes lines that contain a

particular regular expression.

more <url> include

Filters more command output so that it displays only lines that contain
a particular regular expression.

show <command> begin

Searches the output of any show command and displays the output from
the first instance of a specified string.

show <command> exclude Filters show command output so that it excludes lines that contain a
particular regular expression.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-563

show <command> redirect

show <command> redirect

To redirect the output of any show command to a file, use the show command | redirect command in
privileged EXEC mode.
show command | redirect url

Syntax Description

command

Any Cisco IOS show command.

| redirect url

The addition of this syntax redirects the command output to the file location
specified in the Universal Resource Locator (URL). The pipe (|) is required.
The Cisco IOS File System (IFS) uses URLs to specify the location of a file
system, directory, and file. Typical URL elements include:
prefix:[directory/]filename
Prefixes can be local file locations, such as flash: or disk0:. Alternatively,
you can specify network locations using the following syntax:
ftp:[[//[username[:password]@]location]/directory]/filename
tftp:[[//location]/directory]/filename
The rcp: prefix is not supported.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.0(21)S

This command was introduced.

12.2(13)T

This command was integrated into Cisco IOS Release 12.2(13)T.

Usage Guidelines

To display all URL prefixes that are supported for this command, use the show command | redirect ?
command.
This command creates a new file at the specified location, or overwrites an existing file.

Examples

In the following example, output from the show tech-support command is write to the file
showtech.txt on the host at 172.16.101.101 in the directory //tftpboot/docs/ using FTP:
Router# show tech | redirect
ftp://USER:[email protected]//tftpboot/docs/showtech.txt

Related Commands

Command

Description

show <command> append Redirects and appends show command output to the end of an existing
file.
show <command> tee

Copies the show command output to a file while displaying it on the

terminal.

Cisco IOS Configuration Fundamentals Command Reference

CF-564

April 2010

show <command> section

show <command> section

To filter the output of a show command to match a given expression as well as any lines associated with
that expression, use the show command section command in privileged EXEC mode.
show command | section [include | exclude] regular-expression

Syntax Description

command

Any Cisco IOS show command.

include

(Optional) Includes only the lines that contain a particular regular

expression. This is the default keyword when none is specified.

exclude

(Optional) Excludes any lines that contain a particular regular expression.

regular-expression

Any regular expression or plain text string found in show command output.
The syntax of the regular expression conforms to that of Bell V8 regexp(3).

Command Modes

Privileged EXEC

Command History

Release

Modification

12.3(2)T

This command was introduced.

12.2(33)SRE

This command was integrated into Cisco IOS release 12.(33)SRE.

Usage Guidelines

In many cases, it is useful to filter the output of a show command to match a specific expression.
Filtering provides some control over the type and amount of information displayed by the system. The
show section command provides enhanced filtering capabilities by matching lines in the show command
output containing specific expressions as well as matching any entries associated with those expressions.
Filtering is especially useful, for example, when displaying large configuration files using the show
running-configuration command or the show interfaces command.
If the include or exclude keyword is not specified, include is the default.
If there are no associated entries for an expression, then only the line matching the expression is
displayed.

Examples

The following examples compare the filtering characteristics of the show running-config | include
command with the show running-config | section command. The first example gathers just the lines
from the configuration file with interface in them.
Router# show running-config | include interface
interface
interface
interface
interface

Ethernet0/0
Ethernet1/0
Serial2/0
Serial3/0

The next example uses the show command section command to gather the lines in the configuration file
with interface in them as well as any lines associated with those entries. In this example, interface
configuration information is captured.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-565

show <command> section

Router# show running-config | section include interface

interface Ethernet0/0
shutdown
no cdp enable
interface Ethernet1/0
shutdown
no cdp enable
interface Serial2/0
shutdown
no cdp enable
interface Serial3/0
shutdown
no cdp enable

Related Commands

Command

Description

show <command> append

Redirects the output of any show command and adds it to the end of
an existing file.

show <command> exclude

Filters show command output so that it excludes lines that contain a

particular regular expression.

show <command> include

Filters show command output so that it displays only lines that

contain a particular regular expression.

show <command> redirect

Redirects the output of any show command to a specified file.

Cisco IOS Configuration Fundamentals Command Reference

CF-566

April 2010

show <command> tee

show <command> tee

To copy the output of any show command to a file while displaying it on the terminal, use the show
command | tee command in privileged EXEC mode.
show command | tee [/append] url

Syntax Description

command

Any Cisco IOS show command.

| tee url

The addition of this syntax copies the command output to the file location
specified in the Universal Resource Locator (URL). The pipe (|) is required.
The Cisco IOS File System (IFS) uses URLs to specify the location of a file
system, directory, and file. Typical URL elements include:
prefix:[directory/]filename
Prefixes can be local file locations, such as flash: or disk0:. Alternatively,
you can specify network locations using the following syntax:
ftp:[[//[username[:password]@]location]/directory]/filename
tftp:[[//location]/directory]/filename
The rcp: prefix is not supported.

/append

Command Modes

Privileged EXEC

Command History

Release

Usage Guidelines

(Optional) Adds the show command output to the end of an existing file.

Modification

12.0(21)S

This command was introduced.

12.2(13)T

This command was integrated into Cisco IOS Release 12.2(13)T.

To display all URL prefixes that are supported for this command, use the show command | tee ?
command.
The tee keyword was chosen to reflect that output is redirected to two locations; the terminal and a file
(as a tee plumbing junction redirects water to two different pipes).

Examples

In the following example, output from the show tech-support command is displayed on-screen while it
is written to the file showoutput.txt at the host 172.16.101.101 using TFTP:
Router# show tech-support | tee tftp://172.16.101.101/docs/showoutput.txt

The following example performs the same function as above, but in this case the output is added at the
end of any existing data in the file showoutput.txt:
Router# show tech-support | tee /append tftp://172.16.101.101/docs/showoutput.txt

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-567

show <command> tee

Related Commands

Command

Description

show <command> append

Redirects the output of any show command and adds it to the end of
existing file.

show <command> redirect

Redirects the output of any show command to a specified file.

Cisco IOS Configuration Fundamentals Command Reference

CF-568

April 2010

show (Flash file system)

show (Flash file system)

To display the layout and contents of a Flash memory file system, use the show flash-filesystem
command in EXEC mode.
Class A Flash File Systems

show flash-filesystem: [all | chips | filesys]

Class B Flash File Systems

show flash-filesystem:[partition-number:] [all | chips | detailed | err | summary]

Class C Flash File Systems

show flash-filesystem:

Syntax Description

flash-filesystem:

all

Flash memory file system, followed by a colon. The availablity of

Flash file system keywords will vary by platform. Valid flash file
system keywords inlude:

bootflash

flash

slot0

slot1

slavebootflash

slaveslot0

slaveslot1

(Optional) On Class B Flash file systems, all keyword displays

complete information about Flash memory, including information
about the individual ROM devices in Flash memory and the names and
sizes of all system image files stored in Flash memory, including those
that are invalid.
On Class A Flash file systems, the all keyword displays the following
information:

The information displayed when no keywords are used.

The information displayed by the filesys keyword.

The information displayed by the chips keyword.

chips

(Optional) Displays information per partition and per chip, including

which bank the chip is in, plus its code, size, and name.

filesys

(Optional) Displays the Device Info Block, the Status Info, and the
Usage Info.

partition-number

(Optional) Displays output for the specified partition number. If you

do not specify a partition in the command, the router displays output
for all partitions. You can use this keyword only when Flash memory
has multiple partitions.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-569

show (Flash file system)

detailed

(Optional) Displays detailed file directory information per partition,

including file length, address, name, Flash memory checksum,
computer checksum, bytes used, bytes available, total bytes, and bytes
of system Flash memory.

err

(Optional) Displays write or erase failures in the form of number of

retries.

summary

(Optional) Displays summary information per partition, including the

partition size, bank size, state, and method by which files can be
copied into a particular partition. You can use this keyword only when
Flash memory has multiple partitions.

Command Modes

EXEC

Command History

Release

Modification

11.3 AA

This command was introduced.

12.3

A timestamp that shows the offset from Coordinated Universal Time (UTC)
was added to the show command display.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

If Flash memory is partitioned, the command displays the requested output for each partition, unless you
use the partition keyword.
The command also specifies the location of the current image.
To display the contents of boot Flash memory on Class A or B file systems, use the show bootflash:
command as follows:
Class A Flash file systems

show bootflash: [all | chips | filesys]

Class B Flash file systems

show bootflash:[partition-number] [all | chips | detailed | err]

To display the contents of internal Flash memory on Class A or B file systems, use the show flash:
command as follows:
Class A Flash file systems

show flash: [all | chips | filesys]

Class B Flash file systems

show flash:[partition-number][all | chips | detailed | err | summary]

The show (Flash file system) command replaces the show flash devices command.

Examples

The output of the show command depends on the type of Flash file system you select. Types include
flash:, bootflash:, slot0:, slot1:, slavebootflash:, slaveslot0:, and slaveslot1:.

Cisco IOS Configuration Fundamentals Command Reference

CF-570

April 2010

show (Flash file system)

Examples of output from the show flash command are provided in the following sections:

Class A Flash File System

Class B Flash File Systems

Although the examples use flash: as the Flash file system, you may also use the other Flash file systems
listed.
Class A Flash File System

The following three examples show sample output for Class A Flash file systems. Table 49 describes the
significant fields shown in the display.
The following is sample output from the show flash: command.
Router# show flash:
-#- ED --type-- --crc--1
.. unknown 317FBA1B
hampton/nitro/c7200-j-mz
2
.. unknown 9237F3FF
3
.D unknown 71AB01F1
4
.D unknown 96DACD45
5
.. unknown 96DACD45
6
.D unknown 96DACD45
7
.. unknown 96DACD45

-seek-- nlen -length- -----date/time------ name

4A0694
24 4720148 Dec 15 2003 17:49:36 -08:00
92C574
10C94E0
10C97E0
10C9AE0
10C9DE0
10CA0E0

11
10
8
3
8
8

4767328
7982828
639
639
639
639

Jan
Jan
Jan
Jan
Jan
Jan

02
02
03
03
03
03

2004
2004
2004
2004
2004
2004

18:42:53
18:48:14
12:09:17
12:09:32
12:37:01
12:37:13

-08:00
-08:00
-08:00
-08:00
-08:00
-08:00

c7200-js-mz
rsp-jsv-mz
the_time
the_time
the_time
the_time

3104544 bytes available (17473760 bytes used)

Table 49

show (Class A Flash File System) Field Descriptions

Field

Description

Index number for the file.

ED

Whether the file contains an error (E) or is deleted (D).

type

File type (1 = configuration file, 2 = image file). The software

displays these values only when the file type is certain. When
the file type is unknown, the system displays unknown in
this field.

crc

Cyclic redundant check for the file.

seek

Offset into the file system of the next file.

nlen

Name lengthLength of the filename.

length

Length of the file itself.

date/time

Date and time the file was created. In the example, -08:00
indicates that the given date and time is 8 hours behind
Coordinated Universal Time (UTC).

name

Name of the file.

The following is sample output from the show flash: chips command:
RouterA# show flash: chips
******** Intel Series 2+ Status/Register Dump ********
ATTRIBUTE MEMORY REGISTERS:
Config Option Reg (4000): 2

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-571

show (Flash file system)

Config Status
Card Status
Write Protect
Voltage Cntrl
Rdy/Busy Mode

Reg
Reg
Reg
Reg
Reg

(4002):
(4100):
(4104):
(410C):
(4140):

0
1
4
0
2

COMMON MEMORY REGISTERS: Bank 0

Intelligent ID Code : 8989A0A0
Compatible Status Reg: 8080
Global
Status Reg: B0B0
Block Status Regs:
0 : B0B0 B0B0 B0B0 B0B0
8 : B0B0 B0B0 B0B0 B0B0
16 : B0B0 B0B0 B0B0 B0B0
24 : B0B0 B0B0 B0B0 B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

COMMON MEMORY REGISTERS: Bank 1

Intelligent ID Code : 8989A0A0
Compatible Status Reg: 8080
Global
Status Reg: B0B0
Block Status Regs:
0 : B0B0 B0B0 B0B0 B0B0
8 : B0B0 B0B0 B0B0 B0B0
16 : B0B0 B0B0 B0B0 B0B0
24 : B0B0 B0B0 B0B0 B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

COMMON MEMORY REGISTERS: Bank 2

Intelligent ID Code : 8989A0A0
Compatible Status Reg: 8080
Global
Status Reg: B0B0
Block Status Regs:
0 : B0B0 B0B0 B0B0 B0B0
8 : B0B0 B0B0 B0B0 B0B0
16 : B0B0 B0B0 B0B0 B0B0
24 : B0B0 B0B0 B0B0 B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

COMMON MEMORY REGISTERS: Bank 3

Intelligent ID Code : 8989A0A0
Compatible Status Reg: 8080
Global
Status Reg: B0B0
Block Status Regs:
0 : B0B0 B0B0 B0B0 B0B0
8 : B0B0 B0B0 B0B0 B0B0
16 : B0B0 B0B0 B0B0 B0B0
24 : B0B0 B0B0 B0B0 B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

COMMON MEMORY REGISTERS: Bank 4

Intelligent ID Code : 8989A0A0
Compatible Status Reg: 8080
Global
Status Reg: B0B0
Block Status Regs:
0 : B0B0 B0B0 B0B0 B0B0
8 : B0B0 B0B0 B0B0 B0B0
16 : B0B0 B0B0 B0B0 B0B0
24 : B0B0 B0B0 B0B0 B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

B0B0
B0B0
B0B0
B0B0

The following is sample output from the show flash: filesys command:
RouterA# show flash: filesys
-------- F I L E
S Y S T E M
S T A T U S -------Device Number = 0
DEVICE INFO BLOCK:
Magic Number
= 6887635
File System Vers = 10000

(1.0)

Cisco IOS Configuration Fundamentals Command Reference

CF-572

April 2010

show (Flash file system)

Length
= 1400000
Sector Size
= 20000
Programming Algorithm = 4
Erased State
= FFFFFFFF
File System Offset
= 20000
Length = 13A0000
MONLIB Offset
= 100
Length = C730
Bad Sector Map Offset = 1FFEC
Length = 14
Squeeze Log Offset
= 13C0000
Length = 20000
Squeeze Buffer Offset = 13E0000
Length = 20000
Num Spare Sectors
= 0
Spares:
STATUS INFO:
Writable
NO File Open for Write
Complete Stats
No Unrecovered Errors
No Squeeze in progress
USAGE INFO:
Bytes Used
= 10AA0E0 Bytes Available = 2F5F20
Bad Sectors
= 0
Spared Sectors = 0
OK Files
= 4
Bytes = 90C974
Deleted Files = 3
Bytes = 79D3EC
Files w/Errors = 0
Bytes = 0

The following is sample output from the show flash: command:

RouterB> show flash:
System flash directory:
File Length
Name/status
1
4137888 c3640-c2is-mz.Feb24
[4137952 bytes used, 12639264 available, 16777216 total]
16384K bytes of processor board System flash (Read/Write)\

The following example shows detailed information about the second partition in internal Flash memory:
RouterB# show flash:2
System flash directory, partition 2:
File Length
Name/status
1
1711088 dirt/images/c3600-i-mz
[1711152 bytes used, 15066064 available, 16777216 total]
16384K bytes of processor board System flash (Read/Write)

Class B Flash File Systems

Table 50 describes the significant fields shown in the displays.

Table 50

show (Class B Flash File System) all Fields

Field

Description

addr

Address of the file in Flash memory.

available

Total number of bytes available in Flash memory.

Bank

Bank number.

Bank-Size

Size of bank in bytes.

bytes used

Total number of bytes used in Flash memory.

ccksum

Computed checksum.

Chip

Chip number.

Code

Code number.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-573

show (Flash file system)

Table 50

show (Class B Flash File System) all Fields (continued)

Field

Description

Copy-Mode

Method by which the partition can be copied to:

RXBOOT-MANUAL indicates a user can copy manually

by reloading to the boot ROM image.

RXBOOT-FLH indicates user can copy via Flash load

helper.

Direct indicates user can copy directly into Flash memory.

None indicates that it is not possible to copy into that

partition.

fcksum

Checksum recorded in Flash memory.

File

Number of the system image file. If no filename is specified in

the boot system flash command, the router boots the system
image file with the lowest file number.

Free

Number of bytes free in partition.

Length

Size of the system image file (in bytes).

Name

Name of chip manufacturer and chip type.

Name/status

Filename and status of a system image file. The status

[invalidated] appears when a file has been rewritten (recopied)
into Flash memory. The first (now invalidated) copy of the file
is still present within Flash memory, but it is rendered unusable
in favor of the newest version. The [invalidated] status can also
indicate an incomplete file that results from the user abnormally
terminating the copy process, a network timeout, or a Flash
memory overflow.

Partition

Partition number in Flash memory.

Size

Size of partition (in bytes) or size of chip.

State

State of the partition. It can be one of the following values:

Read-Only indicates the partition that is being executed

from.

Read/Write is a partition that can be copied to.

System flash directory

Flash directory and its contents.

total

Total size of Flash memory (in bytes).

Used

Number of bytes used in partition.

The following is sample output from the show flash: all command:
RouterB> show flash: all
Partition
Size
Used
1
16384K
4040K

Free
12343K

Bank-Size
4096K

State
Read/Write

Copy Mode
Direct

System flash directory:

File Length
Name/status
addr
fcksum ccksum
1
4137888 c3640-c2is-mz.Feb24
0x40
0xED65 0xED65

Cisco IOS Configuration Fundamentals Command Reference

CF-574

April 2010

show (Flash file system)

[4137952 bytes used, 12639264 available, 16777216 total]

16384K bytes of processor board System flash (Read/Write)
Chip
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4

Bank
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4

Code
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5

Size
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB

Name
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD

29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080

The following is sample output from the show flash: all command on a router with Flash memory
partitioned:
Router# show flash: all
System flash partition information:
Partition
Size
Used
Free
1
4096K
3459K
637K
2
4096K
3224K
872K

Bank-Size
4096K
4096K

State
Read Only
Read/Write

Copy-Mode
RXBOOT-FLH
Direct

System flash directory, partition 1:

File
Length
Name/status
addr
fcksum
ccksum
1
3459720
master/igs-bfpx.100-4.3
0x40
0x3DE1
0x3DE1
[3459784 bytes used, 734520 available, 4194304 total]
4096K bytes of processor board System flash (Read ONLY)
Chip
Bank
Code
Size
Name
1
1
89A2
1024KB
INTEL 28F008SA
2
1
89A2
1024KB
INTEL 28F008SA
3
1
89A2
1024KB
INTEL 28F008SA
4
1
89A2
1024KB
INTEL 28F008SA
Executing current image from System flash [partition 1]
System flash directory, partition2:
File
Length
Name/status
addr
fcksum
ccksum
1
3224008
igs-kf.100
0x40
0xEE91
0xEE91
[3224072 bytes used, 970232 available, 4194304 total]
4096K bytes of processor board System flash (Read/Write)
Chip
1
2
3
4

Bank
2
2
2
2

Code
89A2
89A2
89A2
89A2

Size
1024KB
1024KB
1024KB
1024KB

Name
INTEL
INTEL
INTEL
INTEL

28F008SA
28F008SA
28F008SA
28F008SA

The following is sample output from the show flash: chips command:

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-575

show (Flash file system)

RouterB> show flash: chips

16384K bytes of processor board System flash (Read/Write)
Chip
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4

Bank
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4

Code
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5

Size
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB

Name
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD

29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080

The following is sample output from the show flash: detailed command:
RouterB> show flash: detailed
System flash directory:
File Length
Name/status
addr
fcksum ccksum
1
4137888 c3640-c2is-mz.Feb24
0x40
0xED65 0xED65
[4137952 bytes used, 12639264 available, 16777216 total]
16384K bytes of processor board System flash (Read/Write)

The following is sample output from the show flash: err command:
RouterB> show flash: err
System flash directory:
File Length
Name/status
1
4137888 c3640-c2is-mz.Feb24
[4137952 bytes used, 12639264 available, 16777216 total]
16384K bytes of processor board System flash (Read/Write)
Chip
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
4

Bank
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4

Code
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5
01D5

Size
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB
1024KB

Name
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD
AMD

erase
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080
29F080

0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

write
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

Cisco IOS Configuration Fundamentals Command Reference

CF-576

April 2010

show (Flash file system)

See Table 50 for a description of the fields. The show flash: err command also displays two extra fields:
erase and write. The erase field indications the number of erase errors. The write field indicates the
number of write errors.
The following is sample output from the show flash summary command on a router with Flash memory
partitioned. The partition in the Read Only state is the partition from which the Cisco IOS image is being
executed.
Router# show flash summary
System flash partition information:
Partition
Size
Used
Free
1
4096K
2048K
2048K
2
4096K
2048K
2048K

Related Commands

Bank-Size
2048K
2048K

State
Read Only
Read/Write

Copy-Mode
RXBOOT-FLH
Direct

Command

Description

more

Displays the contents of any file in the Cisco IOS File System.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-577

show aliases

show aliases
To display all alias commands, or the alias commands in a specified mode, use the show aliases
command in EXEC mode.
show aliases [mode]

Syntax Description

mode

Command Modes

EXEC

Command History

Release

Modification

10.3

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

(Optional) Name of a specific command or configuration mode. Specifies that

only aliases configured for this mode should be displayed.

When used without the mode argument, this command will display all aliases currently configured on
the system. Use the mode argument to display only the aliases configured for the specified command
mode.
To display a list of the command mode keywords available for your system, use the show aliases ?
command.
The following is sample output from the show aliases exec commands. The aliases configured for
commands in EXEC mode are displayed.
Router> show aliases exec
Exec mode aliases:
h
lo
p
r
s
w

Related Commands

help
logout
ping
resume
show
where

Command

Description

alias

Creates a command alias.

Cisco IOS Configuration Fundamentals Command Reference

CF-578

April 2010

show alignment

show alignment
To display alignment errors and spurious memory access errors, use the show alignment command in
privileged EXEC mode.
show alignment

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.3(7)T

This command was introduced.

12.2(22)S

This command was integrated into Cisco IOS Release 12.2(22)S.

12.2(18)SXE

This command was integrated into Cisco IOS Release 12.2(18)SXE.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

Alignment Errors

Alignment errors are caused by misaligned reads and writes. For example, a two-byte read where the
memory address is not an even multiple of two bytes is an alignment error. Alignment errors are caused
by a software defect.
Alignment errors are reported in the system log and recorded by the router. Output from the show
alignment command provides a record of these errors along with potentially useful traceback
information. The traceback information for alignment errors can generally be decoded to reveal the
function causing the alignment problems.
Spurious Memory Access Errors

Spurious memory access errors occur when a software process attempts to access memory in a restricted
location. A read operation to this region of memory is usually caused when a nonexisting value is
returned to a function in the software, or in other words, when a null pointer is passed to a function.
Spurious memory access errors are counted and recorded, if possible, by the software. This information
is displayed with the show alignment command.

Examples

The following is sample output from the show alignment command when alignment detection is
disabled. To enable alignment detection, use the enable command to enter privileged EXEC mode
Router# show alignment
Unaligned handler is disabled

Router#
The following is sample output from the show alignment command when there are no alignment or
spurious memory errors:
Router# show alignment

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-579

show alignment

No alignment data has been recorded.

No spurious memory references have been recorded.
Router#

The following is sample output from the show alignment command when there are only alignment
errors. The traceback information is necessary to determine the cause and the fix of the alignment errors.
Router# show alignment
Total Corrections 134, Recorded 1, Reads 134, Writes 0
Initial
Initial
Address Count Access Type
Traceback
1A014C5
134
32bit read 0x6012F538 0x601338F8 0x601344D8 0x6022D528
No spurious memory references have been recorded.
Router#

Table 51 describes the significant fields shown in the display.

Table 51

show alignment Field Descriptions

Field

Description

Total Corrections

Total number of alignment corrections made.

Recorded

Number of alignment entries.

Reads

Number of misaligned reads.

Writes

Number of misaligned writes.

Initial Address

Address of where the alignment error occurred.

Count

Number of times the alignment occurred at this address.

Initial Access

Address of where the alignment error occurred.

Type

Type of alignment error: read or write.

Traceback

The traceback address information necessary to determine

the cause of the misalignment.

The following is sample output from the show alignment command when there are only spurious
memory access errors:
Router# show alignment
No alignment data has been recorded.
Total Spurious Accesses 50, Recorded 3
Address

Count

E
10
E
20
E
20
Router#

Traceback
0x605351A0 0x603CA084 0x606C4060 0x606D6368 0x60743284 0x60743270
0x605351A0 0x6036EE7C 0x606C4060 0x606D6368 0x60743284 0x60743270
0x605351A0 0x603C998C 0x606D53EC 0x606C4060 0x606D6368 0x60743284

Table 52 describes the significant fields shown in the display.

Cisco IOS Configuration Fundamentals Command Reference

CF-580

April 2010

show alignment

Table 52

show alignment Field Descriptions for Spurious Memory Access Errors

Field

Description

Total Spurious Accesses

Total number of spurious memory accesses made.

Recorded

Number of recorded spurious memory access entries.

Address

Address at which the spurious memory access error occurred.

Count

Number of times the spurious memory access occurred at

each address. The sum equals the Total Spurious Accesses.

Traceback

The traceback address information necessary to determine

the cause of the misalignment.

The following is sample output from the show alignment command when there are alignment errors and
spurious memory access errors:
Router# show alignment
Total Corrections 134, Recorded 1, Reads 134, Writes 0
Initial
Initial
Address Count Access Type
Traceback
1A014C5
134
32bit
read 0x6012F538 0x601338F8 0x601344D8 0x6022D528
Total Spurious Accesses 50, Recorded 3
Address Count Traceback
E
10
0x605351A0 0x603CA084 0x606C4060 0x606D6368 0x60743284 0x60743270
E
20
0x605351A0 0x6036EE7C 0x606C4060 0x606D6368 0x60743284 0x60743270
E
20
0x605351A0 0x603C998C 0x606D53EC 0x606C4060 0x606D6368 0x60743284 x60743270

Related Commands

Command

Description

enable

To enter privileged EXEC mode, or any other security level set by a system
administrator, use the enable command in user EXEC or privileged EXEC
mode.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-581

show archive

show archive
To display information about the files saved in the Cisco IOS configuration archive, use the show
archive command in privileged EXEC mode.
show archive

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.3(7)T

This command was introduced.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(31)SB2

This command was implemented on the Cisco 10000 series.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB and
implemented on the Cisco 10000 series.

Examples

The following is sample output from the show archive command:

Router# show archive
There are currently 1 archive configurations saved.
The next archive file will be named disk0:myconfig-2
Archive # Name
0
1
disk0:myconfig-1 <- Most Recent
2
3
4
5
6
7
8
9
10
11
12
13
14

The following is sample output from the show archive command after several archive files of the
running configuration have been saved. In this example, the maximum number of archive files to be
saved is set to three.
Router# show archive
There are currently 3 archive configurations saved.

Cisco IOS Configuration Fundamentals Command Reference

CF-582

April 2010

show archive

The next archive file will be named disk0:myconfig-8

Archive # Name
0
1
:Deleted
2
:Deleted
3
:Deleted
4
:Deleted
5
disk0:myconfig-5
6
disk0:myconfig-6
7
disk0:myconfig-7 <- Most Recent
8
9
10
11
12
13
14

Table 53 describes the significant fields shown in the displays.

Table 53

Related Commands

show archive Field Descriptions

Field

Description

Archive #

Indicates the number of the running configuration file saved to the Cisco IOS
configuration archive. You can set the maximum number of archive files of
the running configuration to be saved in the configuration archive. The most
recent archive file is the last one shown in the display.

Name

Indicates the name of the running configuration file saved to the Cisco IOS
configuration archive.

Command

Description

archive config

Saves a copy of the current running configuration to the Cisco IOS

configuration archive.

configure confirm

Confirms replacement of the current running configuration with a saved

Cisco IOS configuration file.

configure replace

Replaces the current running configuration with a saved Cisco IOS

configuration file.

maximum

Sets the maximum number of archive files of the running configuration to be

saved in the Cisco IOS configuration archive.

path

Specifies the location and filename prefix for the files in the Cisco IOS
configuration archive.

time-period

Sets the time increment for automatically saving an archive file of the current
running configuration in the Cisco IOS configuration archive.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-583

show archive config differences

show archive config differences

To perform a line-by-line comparison of any two configuration files (accessible through the Cisco IOS
File System [IFS]) and generate a list of the differences between them, use the show archive config
differences command in user EXEC or privileged EXEC mode.
show archive config differences [filename1(path)[filename2(path)][ignorecase]]

Syntax Description

filename1(path)

filename2(path)

ignorecase

Command Default

(Optional) The filename (path) of the first configuration file. Can be files in
the following locations: bootflash:, cns:, fpd:, ftp:, harddisk:, http:, https:,
null:, nvram:, obfl:, pram:, rcp:, revrcsf:, scp:, stby-bootflash:, stby-harddisk:,
stby-nvram:, stby-obfl:, stby-rcsf:, stby-usb0:, stby-usb1:, system:, tar:, tftp:,
tmpsys:, usb0:
(Optional) The filename of the second configuration file. Can be files in the
following locations: bootflash:, cns:, fpd:, ftp:, harddisk:, http:, https:, null:,
nvram:, obfl:, pram:, rcp:, revrcsf:, scp:, stby-bootflash:, stby-harddisk:,
stby-nvram:, stby-obfl:, stby-rcsf:, stby-usb0:, stby-usb1:, system:, tar:,
tftp:, tmpsys:, usb0:
(Optional) Indicates that the case of the filenames should be ignored.

If the filename1(path) and filename2(path) arguments are not specified, the first configuration file is
assumed to be the running configuration file and the second to be the startup configuration file.
If only the filename1(path) argument is specified, the second configuration file is assumed to be the
running configuration file.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.3(4)T

This command was introduced.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(27)SBC

This command was integrated into Cisco IOS Release 12.2(27)SBC.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB and
implemented on the Cisco 10000 series.

Usage Guidelines

Interpreting the output of the show archive config differences command is dependent on the order in
which the two files are configured. Each entry in the generated output list is prefixed with a unique text
symbol to indicate the type of difference found. The text symbols and their meanings are as follows:

A minus symbol (-) indicates that the configuration line exists in filename1(path) but not in
filename2(path).

Cisco IOS Configuration Fundamentals Command Reference

CF-584

April 2010

show archive config differences

Examples

A plus symbol (+) indicates that the configuration line exists in filename2(path) but not in
filename1(path).

An exclamation point (!) with descriptive comments is used to identify order-sensitive configuration
lines whose location is different in filename1(path) than in filename2(path).

In this example, a diff operation is performed on the running and startup configuration files. Table 54
shows the configuration files used for this example.
Table 54

Configuration Files Used for the Diff Operation Example

Running Configuration File

Startup Configuration File

no ip subnet-zero
ip cef
interface Ethernet1/0
ip address 10.7.7.7 255.0.0.0
no ip route-cache
no ip mroute-cache
duplex half
no ip classless
snmp-server community public RO

ip subnet-zero
ip cef
ip name-server 10.4.4.4
voice dnis-map 1
dnis 111
interface Ethernet1/0
no ip address
no ip route-cache
no ip mroute-cache
shutdown
duplex half
ip default-gateway 10.5.5.5
ip classless
access-list 110 deny
ip any
access-list 110 deny
ip any
access-list 110 deny
ip any
snmp-server community private

host 10.1.1.1
host 10.1.1.2
host 10.1.1.3
RW

The following is sample output from the show archive config differences command. This sample output
displays the results of the diff operation performed on the configuration files in Table 54.
Router# show archive config differences running-config startup-config
+ip subnet-zero
+ip name-server 10.4.4.4
+voice dnis-map 1
+dnis 111
interface Ethernet1/0
+no ip address
+shutdown
+ip default-gateway 10.5.5.5
+ip classless
+access-list 110 deny
ip any host 10.1.1.1
+access-list 110 deny
ip any host 10.1.1.2
+access-list 110 deny
ip any host 10.1.1.3
+snmp-server community private RW
-no ip subnet-zero
interface Ethernet1/0
-ip address 10.7.7.7 255.0.0.0
-no ip classless
-snmp-server community public RO

Related Commands

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-585

show archive config differences

Command

Description

more nvram:startup-config

Displays the startup configuration file contained in NVRAM or

specified by the CONFIG_FILE environment variable.

more system:running-config Displays the contents of the currently running configuration file.
show archive config
incremental-diffs

Performs a line-by-line comparison of a specified configuration file to

the running configuration file and generates a list of the configuration
lines that do not appear in the running configuration file.

Cisco IOS Configuration Fundamentals Command Reference

CF-586

April 2010

show archive config incremental-diffs

show archive config incremental-diffs

To perform a line-by-line comparison of a specified configuration file to the running configuration file
and generate a list of the configuration lines that do not appear in the running configuration file, use the
show archive config incremental-diffs command in user EXEC or privileged EXEC mode.
show archive config incremental-diffs file

Syntax Description

file

Command Modes

User EXEC
Privileged EXEC

Command History

Release

The filename of the configuration file to be compared to the running

configuration file.

Modification

12.3(4)T

This command was introduced.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(27)SBC

This command was integrated into Cisco IOS Release 12.2(27)SBC.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB and
implemented on the Cisco 10000 series.

Usage Guidelines

When an incremental diff operation is performed, a list of the configuration lines that do not appear in
the running configuration file (in other words, configuration lines that only appear in the specified file
that is being compared to the running configuration file) is generated as output. An exclamation point
(!) with descriptive comments is used to identify order-sensitive configuration lines whose location is
different in the specified configuration file than in the running configuration file.

Examples

In this example, an incremental diff operation is performed on the startup and running configuration
files. Table 55 shows the configuration files used for this example.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-587

show archive config incremental-diffs

Table 55

Configuration Files Used for the Incremental Diff Operation Example

Startup Configuration File

Running Configuration File

ip subnet-zero
ip cef
ip name-server 10.4.4.4
voice dnis-map 1
dnis 111
interface Ethernet1/0
no ip address
no ip route-cache
no ip mroute-cache
shutdown
duplex half
ip default-gateway 10.5.5.5
ip classless
access-list 110 deny
ip any
access-list 110 deny
ip any
access-list 110 deny
ip any
snmp-server community private

no ip subnet-zero
ip cef
interface Ethernet1/0
ip address 10.7.7.7 255.0.0.0
no ip route-cache
no ip mroute-cache
duplex half
no ip classless
snmp-server community public RO

host 10.1.1.1
host 10.1.1.2
host 10.1.1.3
RW

The following is sample output from the show archive config incremental-diffs command. This sample
output displays the results of the incremental diff operation performed on the configuration files in
Table 55.
Router# show archive config incremental-diffs nvram:startup-config
ip subnet-zero
ip name-server 10.4.4.4
voice dnis-map 1
dnis 111
interface Ethernet1/0
no ip address
shutdown
ip default-gateway 10.5.5.5
ip classless
access-list 110 deny
ip any host 10.1.1.1
access-list 110 deny
ip any host 10.1.1.2
access-list 110 deny
ip any host 10.1.1.3
snmp-server community private RW

Related Commands

Command

Description

more nvram:startup-config

Displays the startup configuration file contained in NVRAM or

specified by the CONFIG_FILE environment variable.

more system:running-config

Displays the contents of the currently running configuration file.

show archive config differences

Performs a line-by-line comparison of any two configuration files

(accessible through the IFS) and generates a list of the differences
between them.

Cisco IOS Configuration Fundamentals Command Reference

CF-588

April 2010

show archive config rollback timer

show archive config rollback timer

To display settings of the timed rollback, use the show archive config rollback timer command in
privileged EXEC mode.
show archive config rollback timer

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.4(15)T

This command was introduced in Cisco IOS Release12.4(15)T.

12.2(33)SRC

This command was integrated into a release earlier than Cisco IOS
Release 12.2(33)SRC.

12.2(33)SXI

This command was integrated into a release earlier than Cisco IOS
Release 12.2(33)SXI.

Cisco IOS XE
Release 2.1

This command was integrated into Cisco IOS XE Release 2.1.

Usage Guidelines

Use the show archive config rollback timer command to display the timed rollback settings, such as
the timer type (idle timer or absolute timer) and timer value, after a timed rollback is configured on a
router.

Examples

The following is sample output from the show archive config rollback timer command:
Router# show archive config rollback timer
Time configured(or reconfigured): 22:50:48 UTC Sat Feb 21 2009
Timer type: absolute timer
Timer value: 2 min
User: console

Table 56 describes the significant fields shown in the display.

Table 56

show archive config rollback timer Field Descriptions

Field

Description

Time configured (or reconfigured)

The time at which the timer refreshes every time the Enter key
is pressed.

Timer type

The type of the timer: Idle or absolute.

Timer value

Displays the time, in minutes, for which to wait for confirmation.

User

Displays the username.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-589

show archive config rollback timer

Related Commands

Command

Description

configure revert

Cancels the timed rollback and trigger the rollback immediately or resets
parameters for the timed rollback.

configure terminal
revert timer

Enter global configuration mode and sets the parameters for reverting the
configuration if confirmation of the new configuration is not received.

Cisco IOS Configuration Fundamentals Command Reference

CF-590

April 2010

show archive log config

show archive log config

To display entries from the configuration log, use the show archive log config command in privileged
EXEC mode.
show archive log config {all | record-number [end-number] | user username [session
session-number] record-number [end-number] | statistics} [provisioning] [contenttype
{plaintext | xml}] [persistent]

Syntax Description

all

Displays all configuration log entries.

record-number
[end-number]

Displays the log entry by record number. If you specify a record number for
the optional end-number argument, all log entries with record numbers
between the values entered for the record-number and end-number
arguments are displayed. Valid values for the record-number and
end-number arguments range from 1 to 2147483647.

user username

Displays log entries attributed to a particular user.

session session-number (Optional) Displays log entries attributed to a particular session. Valid values
for the session-number argument range from 1 to 1000.
statistics

Displays memory usage information for the configuration log.

provisioning

(Optional) Displays configuration log file information as it would appear in

a configuration file, rather than in tabular format.

contenttype

(Optional) Specifies the format for the display of configuration change

results.

plaintext

Specifies that the configuration change results will be formatted as plain

text. This keyword appears only if the contenttype keyword has been
entered.

xml

Specifies that the configuration change results will be in eXtensible Markup

Language (XML) format. This keyword appears only if the contenttype
keyword has been entered.

persistent

(Optional) Displays the persistent configuration changes in a configlet

format.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.3(4)T

This command was introduced.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(27)SBC

This command was integrated into Cisco IOS Release 12.2(27)SBC.

12.2(33)SRA

The contenttype, plaintext, xml, and persistent keywords were added.

12.4(11)T

This command was integrated into Cisco IOS Release 12.4(11)T.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-591

show archive log config

Usage Guidelines

Release

Modification

12.2(33)SXH

This command was integrated into Cisco IOS Release 12.2(33)SXH.

12.2(33)SB

This command with syntax updated in 12.2(33)SRA was integrated into

Cisco IOS Release 12.2(33)SB. This command was implemented on the
Cisco 10000 series.

If you do not specify the all keyword, you must specify a record number with the record-number
argument. You can optionally specify an end record number with the end-number argument to display a
range of records. If you use the end-number argument to specify a record number that does not exist, all
records after the starting record number with a record number lower than that specified with the
end-number argument are displayed.
Specifying the provisioning keyword results in the display appearing as it would in a configuration file,
rather than in tabular format. This output includes commands used to change configuration modes and
logged configuration commands. This output can be used to set up another router if desired.

Examples

The following is sample output from the show archive log config command, which displays
configuration log entry numbers 1 and 2:
Router# show archive log config 1 2
idx
1
2

sess
1
1

user@line
user1@console
user1@console

Logged command
logging enable
logging size 200

Table 57 describes the significant fields shown in the display.

Table 57

show archive log config Field Descriptions

Field

Description

idx

The record number of the configuration log entry.

sess

The session number associated with the configuration log entry.

user@line

The username of the user who executed the command that generated the
configuration log entry.

Logged command

The command that was executed.

The following example results in the display of all configuration log files as they would appear in a
configuration file rather than in tabular format. In addition to displaying logged commands, the example
shows the commands used to change configuration modes that are required to correctly apply the logged
commands.
Router# show archive log config all provisioning
archive
log config
logging enable
logging size 200

The following example results in the display of memory usage statistics for the configuration log:
Router# show archive log config statistics

Cisco IOS Configuration Fundamentals Command Reference

CF-592

April 2010

show archive log config

Config Log Session Info:

Number of sessions being tracked: 1
Memory being held: 3910 bytes
Total memory allocated for session tracking: 3910 bytes
Total memory freed from session tracking: 0 bytes
Config Log log-queue Info:
Number of entries in the log-queue: 3
Memory being held in the log-queue: 671 bytes
Total memory allocated for log entries: 671 bytes
Total memory freed from log entries:: 0 bytes

The output is self-explanatory.

The following example shows the contents of the archive log in XML format:
Router# show archive log config all contenttype xml
<?xml version="1.0" encoding="UTF-8"?>
<configLoggerMsg version="1.0">
<configChanged>
<changeInfo>
<user>jdoe</user>
<async>
<port>con_0</port>
</async>
<when>
<absoluteTime>2003-04-23T20:25:19.847Z</absoluteTime>
</when>
</changeInfo>
<logComment>begin test test1</logComment>
</configChanged>
<configChanged>
<changeInfo>
<user>jdoe</user>
<async>
<port>con_0</port>
</async>
<when>
<absoluteTime>2003-04-23T20:27:19.847Z</absoluteTime>
</when>
</changeInfo>
<changeItem>
<context/>
<enteredCommand>
<cli>interface e0</cli>
</enteredCommand>
<prcResultType>
<prcSuccess>
<change>PRC_CHANGE</change>
</prcSuccess>
</prcResultType>
<oldConfigState>
<cli></cli>
</oldConfigState>
<newConfigState>
<cli>interface e0</cli>
</newConfigState>
</changeItem>
</configChanged>
<configChanged>
<changeInfo>
<user>jdoe</user>
<async>

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-593

show archive log config

<port>con_0</port>
</async>
<when>
<absoluteTime>2003-04-23T20:28:19.847Z</absoluteTime>
</when>
</changeInfo>
<changeItem>
<context><cli>interface e0</cli></context>
<enteredCommand>
<cli>ip address 10.1.1.1 255.255.255.0</cli>
</enteredCommand>
<prcResultType>
<prcSuccess>
<change>PRC_CHANGE</change>
</prcSuccess>
</prcResultType>
<oldConfigState/>
<newConfigState>
<cli>ip address 10.1.1.1 255.255.255.0</cli>
</newConfigState>
</changeItem>
</configChanged>
<configChanged>
<changeInfo>
<user>jdoe</user>
<async>
<port>con_0</port>
</async>
<when>
<absoluteTime>2003-04-23T20:29:19.847Z</absoluteTime>
</when>
</changeInfo>
<logComment>end test test1</logComment>
</configChanged>
</configLoggerMsg>

Cisco IOS Configuration Fundamentals Command Reference

CF-594

April 2010

show as5400

show as5400
To display the hardware details of an application server, use the show as5400 command in
privileged EXEC mode.
show as5400

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.4(22)T

This command was introduced in a release earlier than Cisco IOS

Release 12.4(22)T.

Usage Guidelines

The show as5400 command provides complex troubleshooting information that pertains to the
platform's shared references rather than to a specific interface.

Examples

The following is sample output from the show as5400 command:

Router# show as5400
Hardware Info:
System I/O Controller PLD version:
0x8
Serial Interface Controller PLD version: 0x2
Memory Info:
Memory Installed:
Memory Type is :
Bus Watcher Counters
cor_l2cache_data_ecc_count
bad_l2cache_data_ecc_count
cor_l2cache_tag_ecc_count
bad_l2cache_tag_ecc_count
cor_memory_data_ecc_count
bad_memory_data_ecc_count
bus_errors

1024 MB
DDR

=
=
=
=
=
=
=

0
0
0
0
0
0
0

System Controller Network Interrupts:

Interrupt Register is at 0xB0020040 (0x0000008000000000)
BCM interrupt mask 0xFF7C03BEFFE0FCC2
Registered Interrupts:
Level Mask
0
0x0000000100000000
0
0x0000000000100000
0
0x0000000000080000
0
0x0000040000000000
1
0x0000100000000000

Count
0
26415
0
22982406
0

Data
0x00000000
0xC097F6AC
0x66712B8C
0x00000000
0x00000000

Interrupt Handler
0x6036C144 (GT96124 Interrupt h)
0x60354064 (GigabitEthernet0/1)
0x60354064 (GigabitEthernet0/0)
0x608B2CBC (Low IRQ interrupt)
0x60085D98 (BCM1125 GPIO12 - BI)

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-595

show as5400

1
1
1
1
1
3
4
4
4
4
4
4
4
4
4
6

0x0000000000000020
0x0000000000000010
0x0000000000000008
0x0000000000000004
0x0000080000000000
0x0000800000000000
0x0000400000000000
0x0000200000000000
0x0000004000000000
0x007C00000000E0C2
0x0000000000020000
0x0000000000010000
0x0003000000000000
0x0000000000040000
0x0080000000000000
0x0000000000000001

0
0
0
0
22963823
0
0
0
0
0
0
0
0
0
0
0

HT 600MHz Retry Count 0

BCM1125H HT Host Bridge, handle=0
BCM bridge, config=0x0
(0x00):dev, vendor id
(0x04):status, command
(0x08):class code, revid
(0x0C):hdr, lat timer, cls
(0x18):bus id registers
(0x1C):secondary status
(0x20):mem base/limit
(0x30):io upper limit/base
(0x34):capabilities ptr
(0x38):expansion rom bar
(0x3C):bridge ctrl
(0x40):LDT cmd, cap id,
(0x44):Link config/control
(0x48):Link frequency
(0x50):SRIcmd, srirxden, sritxden
(0x54):SRI tx numerator
(0x58):SRI rx numerator
(0x68):Error status/control
(0x6C):Tx ctrl, databufalloc
(0xC8):Tx buffer count max
(0xDC):Rx CRC expected
(0xF0):Rx CRC received

0xC002880C
0xC0028744
0xC002867C
0xC00285B4
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x64A985BC
0x00000000
0x00000000
0x00000000

=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=

0x608C4ABC
0x608C4ABC
0x608C4ABC
0x608C4ABC
0x608B2F84
0x60380F88
0x608BD1EC
0x608BD1EC
0x608BD1EC
0x608C2FD8
0x608C3A14
0x608C2A7C
0x608C2B4C
0x608C2E04
0x608C2BD4
0x608C2FD8

(SB1125 Timer 3)
(SB1125 Timer 2)
(SB1125 Timer 1)
(SB1125 Timer 0)
(High IRQ interrupt)
(OIR Interrupt)
(NRBUS Parity Error)
(IO Error)
(IO_BUS_Parity Error)
(Spurious Intr ERROR)
(Corrected ECC Error)
(Bad ECC Error Handl)
(BCM1125 Host LDT Br)
(BCM1125 IO-Bus Erro)
(BCM1125 Host PCI Br)
(Watchdog Timer 0 Ha)

0x0002166D
0x00100107
0x06000003
0x00010000
0x001B0100
0x00000141
0x5FF04300
0x00010001
0x00000040
0x00000000
0x00020000
0x20000008
0x00000020
0x801F0423
0x50211010
0x0000FFFF
0x0000FFFF
0x00009A49
0x00041515
0x00FFFFFF
0xBFFFABE0
0x7FF3FFFD

BCM PCI Host Bridge:

bus_no=0, device_no=0
DeviceID=0x0001, VendorID=0x166D, Cmd=0x0146, Status=0x02A0
Cls=0x06/0x00/0x00, Rev=0x03, LatencyTimer=0x2C, CacheLineSize=0x10
BaseAddr0=0x60000008, BaseAddr1=0x00000000, MaxLat=0x00, MinGnt=0x00
SubsysDeviceID=0x0000, SubsysVendorID=0xFFFF, ErrorAddr=0x00030400
Additional Status = 0x00000020
PLX HT2PCI Bridge A for PCM Tracer & DFC 2,4,6, handle=0
PLX HT7520 bridge, config=0x0
(0x00):dev, vendor id
= 0x74501022
(0x04):status, command
= 0x02300107
(0x08):class code, revid
= 0x06040012
(0x0C):hdr, lat timer, cls
= 0x00810000
(0x18):bus id registers
= 0xF80E0201
(0x1C):secondary status
= 0x02200141
(0x20):mem base/limit
= 0x4FF04300
(0x30):io upper limit/base
= 0x00010001
(0x34):capabilities ptr
= 0x000000A0
(0x3C):bridge ctrl
= 0x00020000
(0x40):miscellaneous
= 0x00010004

Cisco IOS Configuration Fundamentals Command Reference

CF-596

April 2010

show as5400

(0x4C):prefetch ctrl
(0xC0):ht cmd, cap id
(0xC4):link cfg/ctrl side a
(0xC8):link cfg/ctrl side b
(0xCC):link freq ctrl side a
(0xD0):link freq ctrl side b

=
=
=
=
=
=

0x00000446
0x00410008
0x00112020
0x770020D0
0x00350422
0x00350402

PLX HT2PCI Bridge B, for DFC 1,3,5,7

(0x00):dev, vendor id
= 0x74501022
(0x04):status, command
= 0x02300107
(0x08):class code, revid
= 0x06040012
(0x0C):hdr, lat timer, cls
= 0x00810000
(0x18):bus id registers
= 0xF81B0F01
(0x1C):secondary status
= 0x022001A1
(0x20):mem base/limit
= 0x5FF05000
(0x30):io upper limit/base
= 0x00010001
(0x34):capabilities ptr
= 0x000000A0
(0x3C):bridge ctrl
= 0x00020000
(0x40):miscellaneous
= 0x000B0004
(0x4C):prefetch ctrl
= 0x00000446

RTC chip is DS1337

Table 58 describes the significant fields shown in the display.

Table 58

show as5400 Field Descriptions

Field

Description

System I/O Controller PLD

version

The version of the programmable logic device (PLD) on the system.

Level

Interrupt priority level.

Mask

Maskable interrupt.

Count

Interrupt count.

Handler

Type of interrupt handler.

RTC chip

Real time clock chip type.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-597

show async bootp

show async bootp

Command

Description

as
Defines an application server on a gateway.
To display the extended BOOTP request parameters that have been configured for asynchronous
interfaces, use the show async bootp command in privileged EXEC mode.
show async bootp

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History

Release

Modification

10.0

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Examples

The following is sample output from the show async bootp command:
Router# show async bootp
The following extended data will be sent in BOOTP responses:
bootfile (for address 192.168.1.1) pcboot
bootfile (for address 172.16.1.111) dirtboot
subnet-mask 255.255.0.0
time-offset -3600
time-server 192.168.1.1

Table 59 describes the significant fields shown in the display.

Table 59

Related Commands

show async bootp Field Descriptions

Field

Description

bootfile... pcboot

Boot file for address 192.168.1.1 is named pcboot.

subnet-mask 255.255.0.0

Subnet mask.

time-offset -3600

Local time is one hour (3600 seconds) earlier than UTC time.

time-server 192.168.1.1

Address of the time server for the network.

Command

Description

async-bootp

Configures extended BOOTP requests for asynchronous interfaces as

defined in RFC 1084.

Cisco IOS Configuration Fundamentals Command Reference

CF-598

April 2010

show autoupgrade configuration unknown

show autoupgrade configuration unknown

To display all of the unknown start-up configuration lines that the auto-upgraded Cisco IOS software
image does not understand, use the show autoupgrade configuration unknown command in privileged
EXEC mode.
show autoupgrade configuration unknown

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.4(15)T

This command was introduced.

Usage Guidelines

Use the show autoupgrade configuration unknown command to view any invalid start-up
configuration. This command prints invalid start-up configuration data only when run from an an image
which was upgraded using the Auto-Upgrade Manager. This command output is useful when you are
upgrading to an image with a different feature set.

Examples

The following example shows how to view the invalid start-up configuration lines that the Cisco IOS
software image, upgraded on the router using AUM, does not understand:
Router# show autoupgrade configuration unknown
! Config Lines not understood by the current image:
voice-card 0
no dspfarm
crypto pki trustpoint aum_cisco_ca
enrollment terminal
revocation-check none
crypto pki certificate chain aum_cisco_ca
certificate ca 40DCB71E54EE24CBE5326F8006BBA4F6 nvram:SecureServer#A4F6CA.cer
no ip http secure-server
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
Total 9 Invalid Config Lines
Router#

Related Commands

Command

Description

upgrade automatic
abortversion

Cancels a scheduled reloading of the device with a new Cisco IOS software
image.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-599

show autoupgrade configuration unknown

Command

Description

upgrade automatic
getversion

Downloads a Cisco IOS software image directly from www.cisco.com or

from a non-Cisco server.

upgrade automatic
runversion

Reloads the device with a new Cisco IOS software image.

Cisco IOS Configuration Fundamentals Command Reference

CF-600

April 2010

show bcm560x

show bcm560x
To display the BCM560x hardware table information, use the show bcm560X command in user EXEC
or privileged EXEC mode.
show bcm560x name {offset | all} [raw]

Syntax Description

name

Displays the bcm50x hardware table name. The hardware table name can be
VLAN table name (VTABLE) or Port based VLAN table name (PTABLE):

offset

Hardware table number. Range is from 0 to 65535

all

Displays all the bcm560x hardware table names.

raw

(Optional) Displays the bcm560x hardware table names.

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History

Release

Modification

12.4(15)T

This command was introduced in a release earlier than Cisco IOS

Release 12.4(15)T.

Examples

The following is sample output from the show bcm560X all command:
Router# show bcm560x VTABLE all
Router# VTABLE.0[0x1]: <VLAN_TAG=1,PORT_BITMAP=0xA000008,UT_PORT_BITMAP=8,MOD_BMAP=0>
*Mar 11 08:07:29.863: VTABLE.0[0x2]:
<VLAN_TAG=2,PORT_BITMAP=0xA000000,UT_PORT_BITMAP=0,MOD_BMAP=0>
*Mar 11 08:07:29.863: VTABLE.0[0x3]:
<VLAN_TAG=0x401,PORT_BITMAP=0xA000000,UT_PORT_BITMAP=0,MOD_BMAP=0>
*Mar 11 08:07:29.867: VTABLE.0[0x4]:
<VLAN_TAG=0xFFF,PORT_BITMAP=0x8000000,UT_PORT_BITMAP=0x8000000,MOD_BMAP=0>
*Mar 11 08:07:29.867:

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-601

show bootflash:

show bootflash:
To display information about the bootflash: file system, use the show bootflash: command in user EXEC
or privileged EXEC mode.
show bootflash: [all | chips | filesys]

Syntax Description

all

(Optional) Displays all possible Flash information.

chips

(Optional) Displays information about the Flash chip.

filesys

(Optional) Displays information about the file system.

Defaults

This command has no default settings.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Examples

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

This example shows how to display information about the file system status:
Router> show bootflash: filesys
-------- F I L E
S Y S T E M
S T A T U S -------Device Number = 0
DEVICE INFO BLOCK: bootflash
Magic Number
= 6887635
File System Vers = 10000
(1.0)
Length
= 1000000
Sector Size
= 40000
Programming Algorithm = 39
Erased State
= FFFFFFFF
File System Offset
= 40000
Length = F40000
MONLIB Offset
= 100
Length = C628
Bad Sector Map Offset = 3FFF8
Length = 8
Squeeze Log Offset
= F80000
Length = 40000
Squeeze Buffer Offset = FC0000
Length = 40000
Num Spare Sectors
= 0
Spares:
STATUS INFO:
Writable
NO File Open for Write
Complete Stats
No Unrecovered Errors
No Squeeze in progress
USAGE INFO:
Bytes Used
= 917CE8 Bytes Available = 628318
Bad Sectors
= 0
Spared Sectors = 0

Cisco IOS Configuration Fundamentals Command Reference

CF-602

April 2010

show bootflash:

OK Files
= 2
Deleted Files = 0
Files w/Errors = 0
Router>

Bytes = 917BE8
Bytes = 0
Bytes = 0

This example shows how to display image information:

Router> show bootflash:
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1
.. image
8C5A393A 237E3C
14 2063804 Aug 23 1999 16:18:45 c6msfc-boot-mz
2
.. image
D86EE0AD 957CE8
9 7470636 Sep 20 1999 13:48:49 rp.halley
Router>

This example shows how to display all bootflash information:

Router> show bootflash: all
-#- ED --type-- --crc--- -seek-- nlen -length- -----date/time------ name
1
.. image
8C5A393A 237E3C
14 2063804 Aug 23 1999 16:18:45 c6msfc-bootmz
2
.. image
D86EE0AD 957CE8
9 7470636 Sep 20 1999 13:48:49 rp.halley
6456088 bytes available (9534696 bytes used)
-------- F I L E
S Y S T E M
S T A T U S -------Device Number = 0
DEVICE INFO BLOCK: bootflash
Magic Number
= 6887635
File System Vers = 10000
(1.0)
Length
= 1000000
Sector Size
= 40000
Programming Algorithm = 39
Erased State
= FFFFFFFF
File System Offset
= 40000
Length = F40000
MONLIB Offset
= 100
Length = C628
Bad Sector Map Offset = 3FFF8
Length = 8
Squeeze Log Offset
= F80000
Length = 40000
Squeeze Buffer Offset = FC0000
Length = 40000
Num Spare Sectors
= 0
Spares:
STATUS INFO:
Writable
NO File Open for Write
Complete Stats
No Unrecovered Errors
No Squeeze in progress
USAGE INFO:
Bytes Used
= 917CE8 Bytes Available = 628318
Bad Sectors
= 0
Spared Sectors = 0
OK Files
= 2
Bytes = 917BE8
Deleted Files = 0
Bytes = 0
Files w/Errors = 0
Bytes = 0
Router>

Related Commands

Command

Description

delete

Marks files on bootflash for deletion.

squeeze

Removes files from bootflash that have been marked for deletion.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-603

show bootvar

show bootvar
To display the contents of the BOOT variable, the name of the configuration file pointed to by the
CONFIG_FILE variable, the contents of the BOOTLDR variable, and the configuration register setting,
use the show bootvar command in user EXEC or privileged EXEC mode.
show bootvar

Syntax Description

This command has no arguments or keywords.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

11.3 AA

This command was introduced.

12.2(14)SX

Support for this command was implemented on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was integrated into
Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

Supported Platforms Other than the Cisco 7600 Series Router

The show bootvar command replaces the show boot command.

The show bootvar command allows you to view the current settings for the following variables:

BOOT

CONFIG_FILE

BOOTLDR

The BOOT variable specifies a list of bootable images on various devices. The CONFIG_FILE variable
specifies the configuration file used during system initialization. The BOOTLDR variable specifies the
flash device and filename containing the rxboot image that ROM uses for booting. You set these
variables with the boot system, boot config, and boot bootldr global configuration commands,
respectively.
When you use this command on a device with multiple Route Switch Processor (RSP) cards (Dual
RSPs), this command also shows you the variable settings for both the master and slave RSP card.
Cisco 7600 Series Router

The show bootvar command displays information about the BOOT environmental variable.
The command output depends on how you configure the boot statement as follows:

If you enter the boot system flash bootflash:sup720_image command in the boot configuration,
then the show bootvar command output displays the bootflash information.

Cisco IOS Configuration Fundamentals Command Reference

CF-604

April 2010

show bootvar

If you enter the boot system flash sup-bootflash:sup720_image command in the boot
configuration, then the show bootvar command output displays the sup-bootflash information. This
action is the correct way of configuring the boot statement.

The show bootvar command is available from the switch processor command-line interface (CLI) and
the route processor CLI. From the switch processor CLI, the display is always bootflash. With either the
bootflash or the sup-bootflash boot statement, the switch boots correctly. You should use sup-bootflash
in the boot configuration statement because the image is stored in the switch processor bootflash; the
route processor sees the image as sup-bootflash.
The number displayed after the image name (for example, c6sup12-js-mz.121-13.E,12) indicates the
number of times that the Cisco 7600 series router tries to reboot the file before giving up.

Examples

Supported Platforms Other than the Cisco 7600 Series Router

The following is sample output from the show bootvar command:

Router# show bootvar
BOOT variable =
CONFIG_FILE variable = nvram:
Current CONFIG_FILE variable = slot0:router-config
BOOTLDR variable not exist
Configuration register is 0x0

In this example, the BOOT variable contains a null string; that is no bootable images are specified.
The CONFIG_FILE variable points to the configuration file in NVRAM as the startup (initialization)
configuration. The run-time value for the CONFIG_FILE variable points to the router-configuration file
on the flash memory card inserted in the first slot of the RSP card. That is, during the run-time
configuration, you have modified the CONFIG_FILE variable using the boot config command, but you
have not saved the run-time configuration to the startup configuration. To save your run-time
configuration to the startup configuration, use the copy system:running-config nvram:startup-config
command. If you do not save the run-time configuration to the startup configuration, then the system
reverts to the saved CONFIG_FILE variable setting for initialization information upon reload. In this
sample, the system reverts to NVRAM for the startup configuration file.
The BOOTLDR variable does not yet exist. That is, you have not created the BOOTLDR variable using
the boot bootldr global configuration command.
The following example is output from the show bootvar command for a Cisco 7513 router configured
for high system availability (HSA):
Router# show bootvar
BOOT variable =
CONFIG_FILE variable =
Current CONFIG_FILE variable =
BOOTLDR variable does not exist
Configuration register is 0x0
current slave is in slot 7
BOOT variable =
CONFIG_FILE variable =
BOOTLDR variable does not exist
Configuration register is 0x0

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-605

show bootvar

Table 60 describes the significant fields shown in the displays.

Table 60

show bootvar Field Descriptions

Field

Description

BOOT variable

Displays a list of specified bootable images.

CONFIG_FILE variable

Indicates where to locate the startup (initialization) configuration

file.

Current CONFIG_FILE variable

Identifies the run-time configuration file.

BOOTLDR variable

Identifies the location of the boot image that ROM uses for
booting, if it is specified.

Configuration register

Specifies router behavior, such as how the router boots, options

while booting, and console speed (baud rate for a terminal
emulation session).

current slave is in slot 7

Indicates the slot where the redundant system is located in HSA

configurations.

Cisco 7600 Series Router

This example shows how to display information about the BOOT environment variable:
Router# show bootvar
BOOT variable = sup-bootflash:c6sup12-js-mz.121-13.E,12
CONFIG_FILE variable =
BOOTLDR variable = bootflash:c6msfc2-boot-mz.121-13.E.bin
Configuration register is 0x2102
Standby is up
Standby has 112640K/18432K bytes of memory.
Standby
Standby
Standby
Standby

BOOT variable = bootflash:c6sup12-js-mz.121-13.E,12

CONFIG_FILE variable =
BOOTLDR variable = bootflash:c6msfc2-boot-mz.121-13.E.bin
Configuration register is 0x2102

The number displayed after the image name (for example, c6sup12-js-mz.121-13.E,12) indicates the
number of times that the Cisco 7600 series router tries to reboot the file before giving up.

Related Commands

Command

Description

boot bootldr

Specifies the location of the boot image that ROM uses for booting.

boot bootstrap

Configures the filename that is used to boot a secondary bootstrap image.

boot config

Specifies the device and filename of the configuration file from which the
router configures itself during initialization (startup).

boot system

Specifies the system image that the router loads at startup.

copy

Copies a file from source to a destination.

show version

Displays the configuration of the system hardware, the software version, the
names and sources of configuration files, and the boot images.

Cisco IOS Configuration Fundamentals Command Reference

CF-606

April 2010

show buffers

show buffers
To display detailed information about the buffer pools on the network server when Cisco IOS, Cisco IOS
Software Modularity, or Cisco IOS XE images are running, use the show buffers command in user
EXEC or privileged EXEC mode.
show buffers [{address hex-address | failures | pool pool-name | detailed | processes | {all |
assigned [process-id] | free | old | input-interface interface-type interface-number} [pool
pool-name]} [dump | header | packet | location pool-location]]
Cisco Catalyst 4500e Series Switches running IOS XE software

show buffers [detailed process id {address hex-address | all | assigned | failures | free |
input-interface interface-type interface-number | old | pool pool-name}[dump | header |
packet | location pool-location]]

Syntax Description

Command Default

address

(Optional) Displays buffers at a specified address.

hex-address

(Optional) Address in hexadecimal notation.

failures

(Optional) Displays buffer allocation failures.

pool

(Optional) Displays buffers in a specified buffer pool.

pool-name

(Optional) Name of buffer pool.

detailed process

(Optional) Displays detailed buffer information.

processes

(Optional) For Cisco IOS Software Modularity images only. Displays buffers
connected to Packet Manager.

all

(Optional) Displays all buffers.

assigned

(Optional) Displays the buffers in use.

process-id

(Optional) For Cisco IOS Software Modularity images only. POSIX process
identifier.

free

(Optional) Displays the buffers available for use.

old

(Optional) Displays buffers older than one minute.

input-interface

(Optional) Displays interface pool information. If an interface type is specified

and this interface has its own buffer pool, information for that pool is
displayed.

interface-type

(Optional) Interface type.

interface-number

(Optional) Interface number.

dump

(Optional) Displays the buffer header and all data.

header

(Optional) Displays the buffer header only.

packet

(Optional) Displays the buffer header and packet data.

location
pool-location

(Optional) Displays all the buffer pools in a given location. The global buffer
pools come first, followed up with process-level buffer pools.

If no options are specified, all buffer pool information is displayed.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-607

show buffers

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History

Release

Modification

10.0

This command was introduced.

12.3

The option to filter display output based on specific buffer pools was
expanded.

12.2(18)SXF4

Two additional fields were added to the output to support Cisco IOS
Software Modularity.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Cisco IOS XE Release This command was introduced on the Cisco Catalyst 4500e Serfies Switches
3.1.0.SG
with support for the detailed process command option.

Examples

Example output varies between Cisco IOS, Cisco IOS Software Modularity, and Cisco IOS XE software
images. To view the appropriate output, choose one of the following sections:

Cisco IOS Software

Cisco IOS Software Modularity

Cisco Catalyst 4500e Series Switches running IOS XE software

Cisco IOS Software

The following is sample output from the show buffers command with no arguments, showing all buffer
pool information:
Router# show buffers
Buffer elements:
398 in free list (500 max allowed)
1266 hits, 0 misses, 0 created
Public buffer pools:
Small buffers, 104 bytes (total 50, permanent 50):
50 in free list (20 min, 150 max allowed)
551 hits, 0 misses, 0 trims, 0 created
Middle buffers, 600 bytes (total 25, permanent 25):
25 in free list (10 min, 150 max allowed)
39 hits, 0 misses, 0 trims, 0 created
Big buffers, 1524 bytes (total 50, permanent 50):
49 in free list (5 min, 150 max allowed)
27 hits, 0 misses, 0 trims, 0 created
VeryBig buffers, 4520 bytes (total 10, permanent 10):
10 in free list (0 min, 100 max allowed)
0 hits, 0 misses, 0 trims, 0 created
Large buffers, 5024 bytes (total 0, permanent 0):
0 in free list (0 min, 10 max allowed)
0 hits, 0 misses, 0 trims, 0 created
Huge buffers, 18024 bytes (total 0, permanent 0):
0 in free list (0 min, 4 max allowed)
0 hits, 0 misses, 0 trims, 0 created
Interface buffer pools:
Ethernet0 buffers, 1524 bytes (total 64, permanent 64):
16 in free list (0 min, 64 max allowed)

Cisco IOS Configuration Fundamentals Command Reference

CF-608

April 2010

show buffers

48 hits, 0 fallbacks
16 max cache size, 16 in cache
Ethernet1 buffers, 1524 bytes (total 64, permanent 64):
16 in free list (0 min, 64 max allowed)
48 hits, 0 fallbacks
16 max cache size, 16 in cache
Serial0 buffers, 1524 bytes (total 64, permanent 64):
16 in free list (0 min, 64 max allowed)
48 hits, 0 fallbacks
16 max cache size, 16 in cache
Serial1 buffers, 1524 bytes (total 64, permanent 64):
16 in free list (0 min, 64 max allowed)
48 hits, 0 fallbacks
16 max cache size, 16 in cache
TokenRing0 buffers, 4516 bytes (total 48, permanent 48):
0 in free list (0 min, 48 max allowed)
48 hits, 0 fallbacks
16 max cache size, 16 in cache
TokenRing1 buffers, 4516 bytes (total 32, permanent 32):
32 in free list (0 min, 48 max allowed)
16 hits, 0 fallbacks
0 failures (0 no memory)

The following is sample output from the show buffers command with no arguments, showing onlybuffer
pool information for Huge buffers. This output shows a highest total of five Huge buffers created five
days and 18 hours before the command was issued.
Router# show buffers
Huge buffers, 18024 bytes (total 5, permanent 0, peak 5 @ 5d18h):
4 in free list (3 min, 104 max allowed)
0 hits, 1 misses, 101 trims, 106 created
0 failures (0 no memory)

The following is sample output from the show buffers command with no arguments, showing only
buffer pool information for Huge buffers. This output shows a highest total of 184 Huge buffers created
one hour, one minute, and 15 seconds before the command was issued.
Router# show buffers
Huge buffers, 65280 bytes (total 4, permanent 2, peak 184 @ 01:01:15):
4 in free list (0 min, 4 max allowed)
32521 hits, 143636 misses, 14668 trims, 14670 created
143554 failures (0 no memory)

The following is sample output from the show buffers command with an interface type and interface
number:
Router# show buffers Ethernet 0
Ethernet0 buffers, 1524 bytes (total 64, permanent 64):
16 in free list (0 min, 64 max allowed)
48 hits, 0 fallbacks
16 max cache size, 16 in cache

Table 61 describes the significant fields shown in the display.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-609

show buffers

Table 61

show buffers (Cisco IOS Software) Field Descriptions

Field

Description

Buffer elements

Small structures used as placeholders for buffers in internal

operating system queues. Used when a buffer may need to be on
more than one queue.

free list

Total number of the currently unallocated buffer elements.

max allowed

Maximum number of buffers that are available for allocation.

hits

Count of successful attempts to allocate a buffer when needed.

misses

Count of buffer allocation attempts that resulted in growing the buffer pool to
allocate a buffer.

created

Count of new buffers created to satisfy buffer allocation attempts when the
available buffers in the pool have already been allocated.

Public Buffer Pools

Small buffers

Buffers that are 104 bytes long.

Middle buffers

Buffers that are 600 bytes long.

Big buffers

Buffers that are 1524 bytes long.

VeryBig buffers

Buffers that are 4520 bytes long.

Large buffers

Buffers that are 5024 bytes long.

Huge buffers

Buffers that are 18,024 bytes long.

total

Total number of this type of buffer.

permanent

Number of these buffers that are permanent.

peak

Maximum number of buffers created (highest total) and the time when that
peak occurred. Formats include weeks, days, hours, minutes, and seconds. Not
all systems report a peak value, which means this field may not display in
output.

free list

Number of available or unallocated buffers in that pool.

min

Minimum number of free or unallocated buffers in the buffer pool.

max allowed

Maximum number of free or unallocated buffers in the buffer pool.

hits

Count of successful attempts to allocate a buffer when needed.

misses

Count of buffer allocation attempts that resulted in growing the buffer pool in
order to allocate a buffer.

trims

Count of buffers released to the system because they were not being used. This
field is displayed only for dynamic buffer pools, not interface buffer pools,
which are static.

created

Count of new buffers created in response to misses. This field is displayed

only for dynamic buffer pools, not interface buffer pools, which are static.

Interface Buffer Pools

total

Total number of this type of buffer.

permanent

Number of these buffers that are permanent.

free list

Number of available or unallocated buffers in that pool.

min

Minimum number of free or unallocated buffers in the buffer pool.

Cisco IOS Configuration Fundamentals Command Reference

CF-610

April 2010

show buffers

Table 61

show buffers (Cisco IOS Software) Field Descriptions (continued)

Field

Description

max allowed

Maximum number of free or unallocated buffers in the buffer pool.

hits

Count of successful attempts to allocate a buffer when needed.

fallbacks

Count of buffer allocation attempts that resulted in falling back to the public
buffer pool that is the smallest pool at least as big as the interface buffer pool.

max cache size

Maximum number of buffers from the pool of that interface that can be in the
buffer pool cache of that interface. Each interface buffer pool has its own
cache. These are not additional to the permanent buffers; they come from the
buffer pools of the interface. Some interfaces place all of their buffers from
the interface pool into the cache. In this case, it is normal for the free list to
display 0.

failures

Total number of times a buffer creation failed. The failure may have occurred
because of a number of different reasons, such as low processor memory, low
IOMEM, or no buffers in the pool when called from interrupt context.

no memory

Number of times there has been low memory during buffer creation. Low or
no memory during buffer creation may not necessarily mean that buffer
creation failed; memory can be obtained from an alternate resource such as a
fallback pool.

Cisco IOS Software Modularity

The following is sample output from the show buffers command using a Cisco IOS Modularity image
from Cisco IOS Release 12.2(18)SXF4 and later releases. Two new output fields were
introducedPublic buffer heads and Temporary buffer headsand are shown within comments in the
following sample output.
Router# show buffers
Buffer elements:
500 in free list (500 max allowed)
106586 hits, 0 misses, 0 created
Public buffer pools:
Small buffers, 104 bytes (total 50, permanent 50, peak 54 @ 1d13h):
49 in free list (20 min, 150 max allowed)
54486 hits, 0 misses, 4 trims, 4 created
0 failures (0 no memory)
Middle buffers, 600 bytes (total 25, permanent 25, peak 27 @ 1d13h):
25 in free list (10 min, 150 max allowed)
20 hits, 0 misses, 2 trims, 2 created
0 failures (0 no memory)
Big buffers, 1536 bytes (total 50, permanent 50):
50 in free list (40 min, 150 max allowed)
6 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
VeryBig buffers, 4520 bytes (total 10, permanent 10):
10 in free list (0 min, 100 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
Large buffers, 5024 bytes (total 0, permanent 0):
0 in free list (0 min, 10 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
Huge buffers, 18024 bytes (total 1, permanent 0, peak 1 @ 1d13h):

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-611

show buffers

0 in free list (0 min, 4 max allowed)

1 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
! Start of Cisco IOS Software Modularity fields
Public buffer headers:
Header buffers, 880 bytes (total 1000, peak 142 @ 1d13h):
864 in permanent free list
142 hits, 0 misses
Temporary buffer headers:
Header buffers, 896 bytes (total 0):
0 in free list
0 hits, 0 misses, 0 trims, 0 created
0 failures
! End of Cisco IOS Software Modularity fields
Interface buffer pools:
Logger Pool buffers, 600 bytes (total 150, permanent 150):
150 in free list (150 min, 150 max allowed)
22 hits, 0 misses

Table 62 describes the significant fields shown in the display that are different from the fields in
Table 61.
Table 62

show buffers (Cisco IOS Software Modularity) Field Descriptions

Field

Description

Public Buffer Headers

Header buffers

Buffers that are 880 bytes long.

total

Total number of this type of buffer.

permanent free list

Number of available or unallocated permanent header buffers.

hits

Count of successful attempts to allocate a header buffer when needed.

misses

Count of buffer allocation attempts that resulted in growing the buffer pool in
order to allocate a buffer.

Temporary Buffer Headers

Header buffers

Buffers that are 896 bytes long.

total

Total number of this type of buffer.

free list

Number of available or unallocated header buffers in that pool.

hits

Count of successful attempts to allocate a buffer when needed.

misses

Count of buffer allocation attempts that resulted in growing the buffer pool in
order to allocate a buffer.

trims

Count of buffers released to the system because they were not being used. This
field is displayed only for dynamic buffer pools, not interface buffer pools,
which are static.

created

Count of new buffers created in response to misses. This field is displayed

only for dynamic buffer pools, not interface buffer pools, which are static.

failures

Total number of allocation requests that have failed because no buffer was
available for allocation; the datagram was lost. Such failures normally occur
at interrupt level.

Cisco IOS Configuration Fundamentals Command Reference

CF-612

April 2010

show buffers

Cisco Catalyst 4500e Series Switches running IOS XE software

The following is sample output from the show buffers command on a Cisco Catalyst 4500e switch, using
a Cisco IOS image from Cisco IOS XE Release 3.1.0.SG and later releases. PDS Public buffers and
Packet information was addedand are shown within comments in the following sample output.
Switch#show buffers
PDS public buffers
Public buffer pools:
Packet buffer, 2048 bytes (total 1000, permanent 1000):
1000 in free list (1000 max allowed)
Header
Packet
0
Buffer
0

pools:
Header Memory, 0 bytes (total 0, permanent 0):
in free list (0 max allowed)
Header Memory, 0 bytes (total 0, permanent 0):
in free list (0 max allowed)

IOSd private buffers:

Buffer elements:
354 in free list (500 max allowed)
27134 hits, 0 misses, 500 created
Public buffer pools:
Small buffers, 104 bytes (total 134, permanent 50, peak 134 @ 01:04:39):
134 in free list (20 min, 150 max allowed)
2554 hits, 28 misses, 0 trims, 84 created
0 failures (0 no memory)
Middle buffers, 600 bytes (total 52, permanent 25, peak 52 @ 01:04:39):
52 in free list (10 min, 150 max allowed)
61 hits, 9 misses, 0 trims, 27 created
0 failures (0 no memory)
Big buffers, 1536 bytes (total 50, permanent 50):
50 in free list (5 min, 150 max allowed)
157 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
VeryBig buffers, 4520 bytes (total 10, permanent 10):
10 in free list (0 min, 100 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
Large buffers, 5024 bytes (total 0, permanent 0):
0 in free list (0 min, 10 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
Huge buffers, 18024 bytes (total 0, permanent 0):
0 in free list (0 min, 4 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
Interface buffer pools:
CF Small buffers, 104 bytes (total 100, permanent 100):
100 in free list (100 min, 200 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
BIPC small buffers, 128 bytes (total 250, permanent 250):
250 in free list (250 min, 250 max allowed)
92 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
BIPC middle buffers, 600 bytes (total 300, permanent 300):
300 in free list (300 min, 300 max allowed)
36 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
CF Middle buffers, 600 bytes (total 100, permanent 100):

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-613

show buffers

100 in free list (100 min, 200 max allowed)

0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
Syslog ED Pool buffers, 600 bytes (total 132, permanent 132):
131 in free list (132 min, 132 max allowed)
5 hits, 0 misses
CF Big buffers, 1536 bytes (total 25, permanent 25):
25 in free list (25 min, 50 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
BIPC buffers, 4096 bytes (total 2, permanent 2):
2 in free list (1 min, 8 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
IPC Emergency buffers, 4096 bytes (total 301, permanent 300, peak 302 @ 01:05:07):
301 in free list (300 min, 300 max allowed)
39 hits, 1 fallbacks, 66 trims, 67 created
0 failures (0 no memory)
0 max cache size, 0 in cache
0 hits in cache, 0 misses in cache
CF VeryBig buffers, 4520 bytes (total 2, permanent 2):
2 in free list (2 min, 4 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
CF Large buffers, 5024 bytes (total 1, permanent 1):
1 in free list (1 min, 2 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
BIPC Medium buffers, 16384 bytes (total 5, permanent 5):
5 in free list (5 min, 5 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
BIPC Large buffers, 65535 bytes (total 2, permanent 2):
2 in free list (2 min, 2 max allowed)
0 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)
IPC small buffers, 128 bytes (total 250, permanent 250):
228 in free list (250 min, 250 max allowed)
124 hits, 0 fallbacks
0 max cache size, 0 in cache
0 hits in cache, 0 misses in cache
IPC middle buffers, 600 bytes (total 200, permanent 200):
200 in free list (200 min, 200 max allowed)
293 hits, 0 fallbacks
0 max cache size, 0 in cache
0 hits in cache, 0 misses in cache
IPC buffers, 4096 bytes (total 300, permanent 300):
298 in free list (300 min, 300 max allowed)
72 hits, 0 fallbacks
0 max cache size, 0 in cache
0 hits in cache, 0 misses in cache
IPC Medium buffers, 16384 bytes (total 30, permanent 30):
30 in free list (30 min, 30 max allowed)
100 hits, 0 fallbacks
0 max cache size, 0 in cache
0 hits in cache, 0 misses in cache
IPC Large buffers, 65535 bytes (total 13, permanent 13):
11 in free list (13 min, 13 max allowed)
19 hits, 0 misses
0 max cache size, 0 in cache
0 hits in cache, 0 misses in cache
Header pools:
Catalyst 4000 buffers, 0 bytes (total 14600, permanent 14600):

Cisco IOS Configuration Fundamentals Command Reference

CF-614

April 2010

show buffers

14600 in free list (0 min, 14601 max allowed)

14600 hits, 0 misses, 0 trims, 0 created
0 failures (0 no memory)

Switch#

The following is sample shows how to run the show buffers detailed command on a Cisco Catalyst
4500e switch, using a Cisco IOS image from Cisco IOS XE Release 3.1.0.SG and later releases and the
various keywords and arguments (Explained in the Syntax Description Table) available.
Switch#
Switch#show buffers ?
detailed Show detailed buffer statistics
|
Output modifiers
<cr>
Switch#show buffers detailed ?
process Show detailed process buffer info
Switch#show buffers detailed process ?
iosd IOSd Process
Switch#show buffers detailed process iosd ?
address
Buffer at a given address
all
All buffers
assigned
Buffers in use
failures
Buffer allocation failures
free
Buffers available for use
input-interface Buffers assigned to an input interface
old
Buffers older than one minute
pool
Buffers in a specified pool
|
Output modifiers
<cr>

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-615

show buffers summary

show buffers summary

To display the buffers usage summary for all caller and for all buffer pools, use the show buffers
summary command in privileged EXEC mode.
show buffers summary

Syntax Description

This command has no arguments or keywords.

Command Default

All buffer usage summary information is displayed.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(33)SXI

This command was introduced.

Examples

The following is sample output from the show buffers summary command:
Router# show buffers summary
Pool: Small
Non-aligned packet(s): 25
Caller Summary
pc = 0x40612F74 count
pc = 0x418D77FC count
pc = 0x418571E0 count
pc = 0x41860488 count

=
=
=
=

37
24
1
1

Pool: Medium
Non-aligned packet(s): 39
Caller Summary
pc = 0x418D77FC count = 38
pc = 0x41860488 count = 1
pc = 0x40612F74 count = 23
Pool: Middle
Non-aligned packet(s): 333
Caller Summary
pc = 0x418D77FC count = 333
pc = 0x40612F74 count = 2
pc = 0x4049FFD8 count = 3
Pool: Big
Non-aligned packet(s): 32078
Caller Summary
pc = 0x418D77FC count = 32006
pc = 0x4065FD40 count = 7
pc = 0x409E915C count = 1
pc = 0x40652A58 count = 65
Pool: VeryBig

Cisco IOS Configuration Fundamentals Command Reference

CF-616

April 2010

show buffers summary

Non-aligned packet(s): 10
Caller Summary
pc = 0x418D77FC count = 10
Pool: Large
Non-aligned packet(s): 8
Caller Summary
pc = 0x418D77FC count = 8
Pool: Huge
Non-aligned packet(s): 2
Caller Summary
pc = 0x418D77FC count = 2

Table 61 describes the significant fields shown in the display.

Table 63

show buffers summary Field Descriptions

Field

Description

Non-alligned

Indicates the number of packets not alligned to 32 bits

PC

Specifies who allocated buffer from this pool, for example, small buffer pool,
middle buffer pool and so on.

Public Buffer Pools

Related Commands

Small buffers

Buffers that are 104 bytes long.

Middle buffers

Buffers that are 600 bytes long.

Big buffers

Buffers that are 1524 bytes long.

VeryBig buffers

Buffers that are 4520 bytes long.

Large buffers

Buffers that are 5024 bytes long.

Huge buffers

Buffers that are 18,024 bytes long.

Command

Description

show buffers

Displays statistics for the buffer pools on the network server.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-617

show c2600

show c2600
To display information for troubleshooting the Cisco 2600 series router, use the show c2600 command
in EXEC mode.
show c2600

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Release

Modification

11.3 XA

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The show c2600 command provides complex troubleshooting information that pertains to the platforms
shared references rather than to a specific interface.

Examples

The following is sample output from the show c2600 command:

Router# show c2600
C2600 Platform Information:
Interrupts:
Assigned Handlers...
Vect Handler
# of Ints
00 801F224C
00000000
01 801DE768
0D3EE155
02 801E94E0
0000119E
04 801F0D94
00000000
05 801E6C34
00000000
06 801F0DE4
00002C1A
07 801F0EA0
0000015D
14 801F224C
00000000
IOS Priority Masks...
Level 00 = [ EF020000
Level 01 = [ EC020000
Level 02 = [ E8020000
Level 03 = [ E0020000
Level 04 = [ E0020000
Level 05 = [ E0020000
Level 06 = [ C0020000
Level 07 = [ 00000000

Name
Xilinx bridge error interrupt
MPC860 TIMER INTERRUPT
16552 Con/Aux Interrupt
PA Network Management Int Handler
Timebase Reference Interrupt
PA Network IO Int Handler
MPC860 CPM INTERRUPT
Xilinx bridge error interrupt

]
]
]
]
]
]
]
]

SIU_IRQ_MASK = FFFFFFFF SIEN

= EF02xxxx
Spurious IRQs = 00000000 SIPEND = 0000xxxx
Interrupt Throttling:
Throttle Count = 00000000
Timer Count

Current Level = 00

= 00000000

Cisco IOS Configuration Fundamentals Command Reference

CF-618

April 2010

show c2600

Netint usec
Active
Longest IRQ

= 00000000
=
0
= 00000000

Netint Mask usec = 000003E8

Configured
=
0

IDMA Status:
Requests = 00000349
Drops
= 00000000
Complete = 00000349
Post Coalesce Frames = 00000349
Giant
= 00000000
Available Blocks = 256/256
ISP Status:
Version string burned in chip: "A986122997"
New version after next program operation: "B018020998"
ISP family type: "2096"
ISP chip ID: 0x0013
Device is programmable

Table 64 describes the significant fields shown in the display.

Table 64

show c2600 Field Descriptions

Field

Description

Interrupts

Denotes that the next section describes the status of the

interrupt services.

Assigned Handlers

Denotes a subsection of the Interrupt section that displays data

about the interrupt handlers.

Vect

The processor vector number.

Handler

The execution address of the handler assigned to this vector.

# of Ints

The number of times this handler has been called.

Name

The name of the handler assigned to this vector.

IOS Priority Masks

Denotes the subsection of the Interrupt section that displays

internal Cisco IOS priorities. Each item in this subsection
indicates a Cisco IOS interrupt level and the bit mask used to
mask out interrupt sources when that Cisco IOS level is being
processed. Used exclusively for debugging.

SIU_IRQ_MASK

For engineering level debug only.

Spurious IRQs

For engineering level debug only.

Interrupt Throttling:

This subsection describes the behavior of the Interrupt

Throttling mechanism on the platform.

Throttle Count

Number of times throttle has become active.

Timer Count

Number of times throttle has deactivated because the maximum

masked out time for network interrupt level has been reached.

Netint usec

Maximum time network level is allowed to run (in

microseconds).

Netint Mask usec

Maximum time network level interrupt is masked out to allow

process level code to run (in microseconds).

Active

Indicates that the network level interrupt is masked or that the

router is in interrupt throttle state.

Configured

Indicates that throttling is enabled or configured when set to 1.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-619

show c2600

Table 64

Related Commands

show c2600 Field Descriptions (continued)

Field

Description

Longest IRQ

Duration of longest network level interrupt (in microseconds).

IDMA Status

Monitors the activity of the Internal Direct Memory Access

(IDMA) hardware and software. Used to coalesce packets (turn
particularized packets into non particularized packets) for
transfer to the process level switching mechanism.

Requests

Number of times the IDMA engine is asked to coalesce a

packet.

Drops

Number of times the coalescing operation was aborted.

Complete

Number of times the operation was successful.

Post Coalesce Frames

Number of Frames completed post coalesce processing.

Giant

Number of packets too large to coalesce.

Available Blocks

Indicates the status of the request queue, in the format N/M

where N is the number of empty slots in queue and M is the total
number of slots; for example, 2/256 indicates that the queue has
256 entries and can accept two more requests before it is full.

ISP Status

Provides status of In-System-Programmable (ISP) hardware.

Version string burned in chip

Current version of ISP hardware.

New version after next program

operation

Version of ISP hardware after next ISP programming operation.

ISP family type

Device family number of ISP hardware.

ISP chip ID

Internal ID of ISP hardware as designated by the chip

manufacturer.

Device is programmable

Yes or No. Indicates if an ISP operation is possible on this

board.

Command

Description

show context

Displays information stored in NVRAM when the router crashes.

Cisco IOS Configuration Fundamentals Command Reference

CF-620

April 2010

show c7200

show c7200
To display information about the CPU and midplane for Cisco 7200 series routers, use the show c7200
command in EXEC mode.
show c7200

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Release

Modification

11.2

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

You can use the output of this command to determine whether the hardware version level and upgrade is
current. The information is generally useful for diagnostic tasks performed by technical support only.

Examples

The following is sample output from the show c7200 command:

Router# show c7200
C7200 Network IO Interrupt Throttling:
throttle count=0, timer count=0
active=0, configured=0
netint usec=3999, netint mask usec=200
C7200 Midplane EEPROM:
Hardware revision 1.2
Board revision
Serial number
2863311530
Part number
Test history
0xAA
RMA number
MAC=0060.3e28.ee00, MAC Size=1024
EEPROM format version 1, Model=0x6
EEPROM contents (hex):
0x20: 01 06 01 02 AA AA AA AA AA AA AA AA 00
0x30: EE 00 04 00 AA AA AA AA AA AA AA 50 AA
C7200 CPU EEPROM:
Hardware revision 2.0
Serial number
3509953
Test history
0x0
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 15 02 00 00 35 8E C1
0x30: 50 00 00 00 FF FF FF FF

A0
170-43690-170
170-170-170

60 3E 28
AA AA AA

Board revision A0
Part number
73-1536-02
RMA number
00-00-00

49 06 00 02 00 00 00 00
FF FF FF FF FF FF FF FF

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-621

show catalyst6000

show catalyst6000
To display the information about the Cisco 7600 series router, use the show catalyst6000 command in
user EXEC or privileged EXEC mode.
show catalyst6000 {all | chassis-mac-address | switching-clock | traffic-meter}

Syntax Description

all

Displays the MAC-address ranges and the current and peak traffic-meter
reading.

chassis-mac-address

Displays the MAC-address range.

switching-clock

Displays the failure recovery mode of the switching clock.

traffic-meter

Displays the percentage of the backplane (shared bus) utilization.

Defaults

all

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

If you enter the switching-clock keywords, the Cisco 7600 series router displays whether switching of
the redundant clock sources on the backplane is allowed if the active clock source fails.
The Cisco 7600 series router has either 64 or 1024 MAC addresses that are available to support the
software features. You can enter the show catalyst6000 chassis-mac-address command to display the
MAC-address range on your chassis.

Examples

This example shows how to display the MAC-address ranges and the current and peak traffic-meter
readings:
Router> show catalyst6000 all
chassis MAC addresses: 64 addresses from 0001.6441.60c0 to 0001.6441.60ff
traffic meter =
0% Never cleared
peak =
0% reached at 08:14:38 UTC Wed Mar 19 2003
switching-clock: clock switchover and system reset is allowed
Router>

This example shows how to display the MAC-address ranges:

Router# show catalyst6000 chassis-mac-address

Cisco IOS Configuration Fundamentals Command Reference

CF-622

April 2010

show catalyst6000

chassis MAC addresses: 1024 addresses from 00d0.004c.1800 to 00d0.004c.1c00

Router#

This example shows how to display the current and peak traffic-meter readings:
Router> show catalyst6000 traffic-meter
traffic meter = 0%
Router#

peak = 0%

at

09:57:58 UTC Mon Nov 6 2000

This example shows how to display the failure recovery mode of the switching clock:
Router> show catalyst6000 switching-clock
switching-clock: clock switchover and system reset is allowed
Router>

Related Commands

Command

Description

show environment alarm

Displays the information about the environmental alarm.

show fm summary

Displays a summary of FM Information.

show environment status

Displays the information about the operational FRU status.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-623

show cls

show cls
To display the current status of all Cisco link services (CLS) sessions on the router, use the show cls
command in EXEC mode.
show cls [brief]

Syntax Description

brief

Defaults

Without the brief keyword, displays complete output.

Command Modes

EXEC

Command History

Release

Modification

11.0

This command was introduced in a release prior to Cisco IOS Release 11.0.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

(Optional) Displays a brief version of the output.

The Cisco link service (CLS) is used as the interface between data link users (DLUs), such as DLSw,
LAN Network Manager (LNM), downstream physical unit (DSPU), and SNASw, and their
corresponding data link circuits (DLCs) such as Logic Link Control (LLC), VDLC, and Qualified Logic
Link Control (QLLC). Each DLU registers a particular service access point (SAP) with CLS, and
establishes circuits through CLS over the DLC.
The show cls command displays the SAP values associated with the DLU and the circuits established
through CLS.
For further information about CLS, use the Release 12.2 Cisco IOS Bridging and IBM Networking
Configuration Guide.

Examples

The following is sample output from the show cls command:

IBD-4500B# show cls
DLU user:SNASW
SSap:0x04 VDLC VDLC650
DTE:1234.4000.0001 1234.4000.0002 04 04
T1 timer:0
T2 timer:0 Inact timer:0
max out:0
max in:0
retry count:10
XID retry:10 XID timer:5000 I-Frame:0
flow:0
DataIndQ:0
DataReqQ:0
DLU user:DLSWDLUPEER
DLU user:DLSWDLU
Bridging VDLC VDLC1000
Bridging VDLC VDLC650

The following is sample output from the show cls brief command:

Cisco IOS Configuration Fundamentals Command Reference

CF-624

April 2010

show cls

IBD-4500B# show cls brief

DLU user:SNASW
SSap:0x04 VDLC VDLC650
DTE:1234.4000.0001 1234.4000.0002 04 04
DLU user:DLSWDLUPEER
DLU user:DLSWDLU
Bridging VDLC VDLC1000
Bridging VDLC VDLC650

The examples show two DLUsSNASw and DLSwactive in the router. SNASw uses a SAP value of
0x04, and the associated DLC port is VDLC650. SNASw has a circuit established between MAC
addresses 1234.4000.0001 and 1234.4000.0002 using source and destination SAPs 04 and 04. DLSw is
a bridging protocol and uses VDLC1000 and VDLC650 ports. There are no circuits in place at this time.
In the output from the show cls command (without the brief argument), the values of timers and counters
applicable to this circuit are displayed.

Related Commands

Command

Description

stun peer-name

Enables STUN for an IP address and uses Cisco Link Services (CLS) to
access the Frame Relay network.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-625

show config id

show config id
The configuration change tracking identifier (CTID) assigns a version number to each saved version of
the running-config file. To display output about the versions, use the show config id command in
privileged EXEC mode.
show config id [detail]

Syntax Description

detail

Command Default

This command is disabled by default. If this command is not entered, the management system has to
query the device for the current running-config file and then compare the results to the last known
configuration to determine if a change has been made.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(33)SRC

This command was introduced.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB and
implemented on the Cisco 10000 series.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T.

Usage Guidelines

(Optional) Expands the output of the command to include the ID of the last
user to make a configuration change and the process in which the changes
were made.

This configuration infrastructure command assigns a version number that is updated every time the
running-config file is changed. This version number is called the configuration change tracking identifier
or CTID. The CTID can be used to compare configuration files to track configuration changes and take
appropriate actions (for example, a configuration rollback). Config Logger can also use the CTID to
determine if there have been any changes to the running-config file.
CTID makes the management system more efficient by presenting information that indicates a change
has been made to the running-config file. Without CTID, the management system has to query the device
for the current running-config file and then compare the results to the last known configuration to
determine if a change has been made.

Examples

The following example shows that the current running-config file is version 4 and that this file was saved
on June 15, 2006 at 7.572 seconds after 3:02 p.m.:
Router# show config id
version:4 time:2006-06-15T15:02:07.572Z

Cisco IOS Configuration Fundamentals Command Reference

CF-626

April 2010

show config id

The following example shows that the current running-config file is version 9 and that this file was last
saved on June 18, 2006 at 34.431 seconds after 6:34 p.m. The file was saved by the system and changed
from Init:
Router# show config id detail
Configuration version : 9
Last change time : 2006-06-18T18:34:34.431Z
Changed by user : system
Changed from process : Init

Field descriptions are self-explanatory.

Related Commands

Command

Description

copy running-config
startup-config

Copies the current running-config file (source) to the startup-config file

(destination).

show running-config

Displays the contents of the currently running configuration file or the

configuration for a specific class map, interface, map class, policy map, or
virtual-circuit class.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-627

show configuration id

show configuration id
To display output about configuration versions, use the show configuration id command in privileged
EXEC mode.
show configuration id [detail]

Syntax Description

detail

Command Default

This command is disabled by default. If this command is not entered, the management system has to
query the device for the current running-config file and then compare the results to the last known
configuration to determine if a change has been made.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(33)SRC

This command was introduced.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB and
implemented on the Cisco 10000 series.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T.

Cisco IOS XE
Release 2.5

This command was implemented on Cisco ASR 1000 Series Aggregation

Services Routers.

Usage Guidelines

(Optional) Expands the output of the command to include the ID of the last
user to make a configuration change and the process in which the changes
were made.

This configuration infrastructure command assigns a version number that is updated every time the
running-config file is changed. This version number is called the configuration change tracking identifier
(CTID). The CTID assigns a version number to each saved version of the running-config file. The CTID
can be used to compare configuration files to track configuration changes and take appropriate actions
(for example, a configuration rollback). Config Logger can also use the CTID to determine if there have
been any changes to the running-config file.
CTID makes the management system more efficient by presenting information that indicates a change
has been made to the running-config file. Without CTID, the management system has to query the device
for the current running-config file and then compare the results to the last known configuration to
determine if a change has been made.

Examples

The following example shows that the current running-config file is version 4 and that this file was saved
on June 15, 2006 at 7.572 seconds after 3:02 p.m.:
Router# show configuration id
version:4 time:2006-06-15T15:02:07.572Z

Cisco IOS Configuration Fundamentals Command Reference

CF-628

April 2010

show configuration id

The following example shows that the current running-config file is version 9 and that this file was last
saved on June 18, 2006 at 34.431 seconds after 6:34 p.m. The file was saved by the system and changed
from Init. The field descriptions are self-explanatory.
Router# show configuration id detail
Configuration version : 9
Last change time : 2006-06-18T18:34:34.431Z
Changed by user : system
Changed from process : Init

Related Commands

Command

Description

copy running-config
startup-config

Copies the current running-config file (source) to the startup-config file

(destination).

show running-config

Displays the contents of the currently running configuration file or the

configuration for a specific class map, interface, map class, policy map, or
virtual-circuit class.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-629

show configuration lock

show configuration lock

To display information about the lock status of the running configuration file during a configuration
replace operation, use the show configuration lock command in privileged EXEC mode.
show configuration lock

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.2(25)S

This command was introduced.

12.3(14)T

This command was integrated into Cisco IOS Release 12.3(14)T.

The output of this command was updated to display the configuration
locking class.

Examples

12.0(31)S

The command output was enhanced.

12.2(28)SB

This command was integrated into Cisco IOS Release 12.2(28)SB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(31)SB2

This command was implemented on the Cisco 10000 series.

12.2(33)SXH

This command was integrated into Cisco IOS Release 12.2(33)SXH.

12.2(33)SB

This command was integrated into Cisco IOS Release 12.2(33)SB and
implemented on the Cisco 10000 series.

The following is sample output from the show configuration lock command when the running
configuration file is locked by another user.
Cisco IOS Release 12.2(25)S, Release 12.2(28)SB, Release 12.3(14)T, and Later Releases
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)# configuration mode exclusive ?
auto
manual

Lock configuration mode automatically

Lock configuration mode on-demand

Router(config)# configuration mode exclusive auto

Router(config)# end
Router# show running-config | include configuration
configuration mode exclusive auto
Router# configure terminal

!<-----------

Acquires the lock

Enter configuration commands, one per line. End with CNTL/Z.

Cisco IOS Configuration Fundamentals Command Reference

CF-630

April 2010

show configuration lock

Router(config)# show configuration lock

Parser Configure Lock
--------------------Owner PID : 3
User : unknown
TTY : 0
Type : EXCLUSIVE
State : LOCKED
Class : EXPOSED
Count : 1
Pending Requests : 0
User debug info : configure terminal
Router(config)#
Router(config)# end
! <------------

Releases the lock

The following is sample output from the show configuration lock command when the running
configuration file is not locked by another user.
Router# show configuration lock
Parser Configure Lock
--------------------Owner PID : -1
User : unknown
TTY : -1
Type : NO LOCK
State : FREE
Class : unknown
Count : 0
Pending Requests : 0
User debug info :

Cisco IOS Release 12.0(31)S, 12.2(33)SRA, and Later Releases

Router# show configuration lock
Parser Configure Lock
-----------------------------------------------------Owner PID
: 3
User
: unknown
TTY
: 0
Type
: EXCLUSIVE
State
: LOCKED
Class
: EXPOSED
Count
: 1
Pending Requests
: 0
User debug info
: configure terminal
Session idle state
: TRUE
No of exec cmds getting executed : 0
No of exec cmds blocked
: 0
Config wait for show completion
: FALSE
Remote ip address
: Unknown
Lock active time (in Sec)
: 6
Lock Expiration timer (in Sec)
: 593

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-631

show configuration lock

Table 65 describes the significant fields shown in the displays.

Table 65

show configuration lock Field Descriptions

Field

Description

Owner PID

Process identifier (PID) of the process that owns the lock.

User

Owners username.

TTY

Owners terminal number.

Type

Lock type (EXCLUSIVE/COUNTER/NO LOCK).

State

State of the lock (FREE/LOCKED).

Class

Classification of users of the lock (EXPOSED/ROLLBACK).

Processes other than ROLLBACK belong to the EXPOSED class.

Count

In the case of a counter lock, total number of processes holding the

lock.

Pending Requests

Total number of processes blocked by the lock.

User debug info

Any string given by the process (used for debugging only).

Session idle state

Indicates whether the user in an access session locking session is

idle. Displays TRUE or FALSE.

No of exec cmds getting

executed

Total number of EXEC commands (show and clear) being

executed simultaneously from different sessions.

No of exec cmds blocked

Total number of EXEC commands (show and clear) waiting for the
configuration command (running from the access session locking
session) to complete its execution.

Config wait for show completion Indicates whether a configuration command executed in an access
session locking session is waiting for the completion of the show
command being executed simultaneously from a different session.
Displays TRUE or FALSE.
Remote ip address

IP address of the terminal from which the user telneted to the

router.

Lock active time (in Sec)

Amount of time, in seconds, that elapsed since the lock was

acquired.

Lock Expiration timer (in Sec)

The amount of time, in seconds, that expires before the lock is

automatically released.

The following example shows how to configure the configuration file for single user auto configuration
mode (using the configuration mode exclusive auto command). Use the configure terminal command
to enter global configuration mode and lock the configuration mode exclusively. Once the Cisco IOS
configuration mode is locked exclusively, you can verify the lock using the show configuration lock
command.
Router# configure terminal
Router(config)# configuration mode exclusive auto
Router(config)# end
Router# configure terminal
Router(config)# show configuration lock
Parser Configure Lock

Cisco IOS Configuration Fundamentals Command Reference

CF-632

April 2010

show configuration lock

Owner PID
User
TTY
Type
State
Class
Count
Pending Requests
User debug info

Related Commands

:
:
:
:
:
:
:
:
:

10
User1
3
EXCLUSIVE
LOCKED
Exposed
0
0
0

Command

Description

configuration mode exclusive

Enables single-user (exclusive) access functionality for the

Cisco IOS CLI.

configure replace

Replaces the current running configuration with a saved

Cisco IOS configuration file.

debug configuration lock

Enables debugging of the Cisco IOS configuration lock.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-633

show context

show context
To display information stored in NVRAM when an unexpected system reload (system exception) occurs,
use the show context command in user EXEC or priviledged EXEC mode.
show context [summary | all | slot slot-number [crash-index] [all] [debug]]

Syntax Description

Command Modes

summary

Displays a summary of all the crashes recorded.

all

Displays all crashes for all the slots. When optionally used with the slot
keyword, displays crash information for the specified slot.

slot slot-number
[crash-index]

Displays information for a particular line card. Slot numbers range

from 0 to 11 for the Cisco 12012 router and from 0 to 7 for the Cisco 12008.
The index number allows you to look at previous crash contexts. Contexts
from the last 24 line card crashes are saved on the GRP card. If the GRP
reloads, the last 24 line card crash contexts are lost. For example,
show context slot 3 2 shows the second most recent crash for line card in slot
3. Index numbers are displayed by the show context summary command.

debug

(Optional) Displays crash information as a hex record dump in addition to one

of the options listed.

User EXEC
Privileged EXEC

Command History

Usage Guidelines

Note

Release

Modification

10.3

This command was introduced.

11.2 GS

The slot slot-number [crash-index] [all] [debug] syntax was added for
Cisco 12000 series routers.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

The display from the show context command includes the following information:

Reason for the system reboot

Stack trace

Software version

The signal number, code, and router uptime information

All the register contents at the time of the crash

This command is primarily for use by Cisco technical support representatives for analyzing unexpected
system reloads.

Cisco IOS Configuration Fundamentals Command Reference

CF-634

April 2010

show context

Output for this command will vary by platform. Context information is specific to processors and
architectures. For example, context information for the Cisco 2600 series router differs from that for
other router types because the Cisco 2600 runs with an M860 processor.

Examples

The following is sample output from the show context command following a system failure:
Router> show context
System was restarted by error - a Software forced crash, PC 0x60189354
GS Software (RSP-PV-M), Experimental Version 11.1(2033) [ganesh 111]
Compiled Mon 31-Mar-97 13:21 by ganesh
Image text-base: 0x60010900, data-base: 0x6073E000
Stack trace from system failure:
FP: 0x60AEA798, RA: 0x60189354
FP: 0x60AEA798, RA: 0x601853CC
FP: 0x60AEA7C0, RA: 0x6015E98C
FP: 0x60AEA7F8, RA: 0x6011AB3C
FP: 0x60AEA828, RA: 0x601706CC
FP: 0x60AEA878, RA: 0x60116340
FP: 0x60AEA890, RA: 0x6011632C
Fault History Buffer:
GS Software (RSP-PV-M), Experimental Version 11.1(2033) [ganesh 111]
Compiled Mon 31-Mar-97 13:21 by ganesh
Signal = 23, Code = 0x24, Uptime 00:04:19
$0 : 00000000, AT : 60930120, v0 : 00000032, v1 : 00000120
a0 : 60170110, a1 : 6097F22C, a2 : 00000000, a3 : 00000000
t0 : 60AE02A0, t1 : 8000FD80, t2 : 34008F00, t3 : FFFF00FF
t4 : 00000083, t5 : 3E840024, t6 : 00000000, t7 : 11010132
s0 : 00000006, s1 : 607A25F8, s2 : 00000001, s3 : 00000000
s4 : 00000000, s5 : 00000000, s6 : 00000000, s7 : 6097F755
t8 : 600FABBC, t9 : 00000000, k0 : 30408401, k1 : 30410000
gp : 608B9860, sp : 60AEA798, s8 : 00000000, ra : 601853CC
EPC : 60189354, SREG : 3400EF03, Cause : 00000024
Router>

The following is sample output from the show context summary command on a Cisco 12012 router.
The show context summary command displays a summary of all the crashes recorded for each slot (line
card).
Router# show context summary
CRASH INFO SUMMARY
Slot 0 : 0 crashes
Slot 1 : 0 crashes
Slot 2 : 0 crashes
Slot 3 : 0 crashes
Slot 4 : 0 crashes
Slot 5 : 0 crashes
Slot 6 : 0 crashes
Slot 7 : 2 crashes
1 - crash at 18:06:41 UTC Tue Nov 5 1996
2 - crash at 12:14:55 UTC Mon Nov 4 1996
Slot 8 : 0 crashes
Slot 9 : 0 crashes
Slot 10: 0 crashes
Slot 11: 0 crashes
Router#

The following is sample output from the show context command following an unexpected system reload
on a Cisco 2600 series router.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-635

show context

router# show context

S/W Version: Cisco IOS Software
Cisco IOS (tm) c2600 Software (c2600-JS-M), Released Version 11.3(19980115:184921]
Copyright (c) 1986-2003 by Cisco Systems, Inc.
Compiled Thu 15-Jan-98 13:49 by mmagno
Exception occurred at: 00:02:26 UTC Mon Mar 1 1993
Exception type: Data TLB Miss (0x1200)
CPU Register Context:
PC = 0x80109964 MSR = 0x00009030 CR = 0x55FFFD35 LR
= 0x80109958
CTR = 0x800154E4 XER = 0xC000BB6F DAR = 0x00000088 DSISR = 0x00000249
DEC = 0x7FFFDFCA TBU = 0x00000000 TBL = 0x15433FCF IMMR = 0x68010020
R0 = 0x80000000 R1 = 0x80E80BD0 R2 = 0x80000000 R3
= 0x00000000
R4 = 0x80E80BC0 R5 = 0x40800000 R6 = 0x00000001 R7
= 0x68010000
R8 = 0x00000000 R9 = 0x00000060 R10 = 0x00001030 R11
= 0xFFFFFFFF
R12 = 0x00007CE6 R13 = 0xFFF379E8 R14 = 0x80D50000 R15
= 0x00000000
R16 = 0x00000000 R17 = 0x00000000 R18 = 0x00000000 R19
= 0x00000000
R20 = 0x00000000 R21 = 0x00000001 R22 = 0x00000010 R23
= 0x00000000
R24 = 0x00000000 R25 = 0x80E91348 R26 = 0x01936010 R27
= 0x80E92A80
R28 = 0x00000001 R29 = 0x019BA920 R30 = 0x00000000 R31
= 0x00000018
Stack trace:
Frame 00: SP = 0x80E80BD0
PC = 0x80109958
Frame 01: SP = 0x80E80C28
PC = 0x8010A720
Frame 02: SP = 0x80E80C40
PC = 0x80271010
Frame 03: SP = 0x80E80C50
PC = 0x8025EE64
Frame 04: SP = 0x80DEE548
PC = 0x8026702C
Frame 05: SP = 0x80DEE558
PC = 0x8026702C

Table 66 describes the significant fields shown in the display.

Table 66

Related Commands

show context Field Descriptions

Field

Description

S/W Version

Standard Cisco IOS version string as displayed.

Exception occurred at

Router real time when exception occurred. The router must have
the clock time properly configured for this to be accurate.

Exception type

Technical reason for exception. For engineering analysis.

CPU Register Context

Technical processor state information. For engineering analysis.

Stack trace

Technical processor state information. For engineering analysis.

Command

Description

show processes

Displays information about the active processes.

show stacks

Monitors the stack usage of processes and interrupt routines.

Cisco IOS Configuration Fundamentals Command Reference

CF-636

April 2010

show controllers (GRP image)

show controllers (GRP image)

To display information that is specific to the hardware, use the show controllers command in privileged
EXEC mode.
show controllers [atm slot-number | clock | csar [register] | csc-fpga | dp83800 | fab-clk | fia
[register] | pos [slot-number] [details] | queues [slot-number] | sca | xbar]

Syntax Description

Command Modes

atm slot-number

(Optional) Displays the ATM controllers. Number is slot-number/

port-number (for example, 4/0). Slot numbers range from 0 to 11 for the
Cisco 12012 router and from 0 to 7 for the Cisco 12008 router.

clock

(Optional) Displays the clock card configuration.

csar [register]

(Optional) Displays the Cisco Cell Segmentation and Reassembly

(CSAR) information. CSAR is the name of the chip on the card that
handles traffic between the GRP and the switch fabric interface ASICs.

csc-fpga

(Optional) Displays the clock and scheduler card register information in

the field programmable gate array (FPGA).

dp83800

(Optional) Displays the Ethernet information on the GRP card.

fab-clk

(Optional) Display the switch fabric clock register information. The

switch fabric clock FPGA is a chip that monitors the incoming fabric
clock generated by the switch fabric. This clock is needed by each card
connecting to the switch fabric to properly communicate with it. Two
switch fabric clocks arrive at each card; only one can be used. The FPGA
monitors both clocks and selects which one to use if only one of them is
running.

fia [register]

(Optional) Displays the fabric interface ASIC information and optionally

displays the register information.

pos [slot-number]
[details]

(Optional) Displays the POS framer state and optionally displays all the
details for the interface. Number is slot-number/port-number (for
example, 4/0). Slot numbers range from 0 to 11 for the Cisco 12012
router and from 0 to 7 for the Cisco 12008 router.

queues [slot-number]

(Optional) Displays the SDRAM buffer carve information and optionally

displays the information for a specific line card. The SDRAM buffer
carve information displayed is suggested carve information from the GRP
card to the line card. Line cards might change the shown percentages
based on SDRAM available. Slot numbers range from 0 to 11 for the
Cisco 12012 router and from 0 to 7 for the Cisco 12008.

sca

(Optional) Displays the SCA register information. The SCA is an ASIC

that arbitrates among the line cards requests to use the switch fabric.

xbar

(Optional) Displays the crossbar register information. The XBAR is an

ASIC that switches the data as it passes through the switch fabric.

Privileged EXEC

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-637

show controllers (GRP image)

Command History

Release

Modification

11.2 GS

This command was introduced to support the Cisco 12000 series routers.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

This information provided by this command is intended for use only by technical support representatives
in analyzing system failures in the field.

Examples

The following is sample output from the show controllers pos command for a Cisco 12012:
Router# show controllers pos 7/0
POS7/0
SECTION
LOF = 2
LOS = 0
Active Alarms: None
LINE
AIS = 2
RDI = 2
FEBE = 146
Active Alarms: None
PATH
AIS = 2
RDI = 4
FEBE = 63
LOP = 0
PSE = 8
NSE = 3
Active Alarms: None
APS
COAPS = 3
PSBF = 2
State: PSBF_state = False
Rx(K1/K2): F0/15 Tx(K1/K2): 00/00
S1S0 = 00, C2 = 64
PATH TRACE BUFFER : STABLE
Remote hostname : GSR-C
Remote interface: POS10/0
Remote IP addr : 10.201.101.2
Remote Rx(K1/K2): F0/15 Tx(K1/K2): 00/00
Router#

Related Commands

Command

Description

clear controllers

Resets the T1 or E1 controller.

BIP(B1) = 5889

BIP(B2) = 2106453

BIP(B3) = 3216
NEWPTR = 2

show controllers (line Displays information that is specific to the hardware on a line card.
card image)

Cisco IOS Configuration Fundamentals Command Reference

CF-638

April 2010

show controllers (line card image)

show controllers (line card image)

To display information that is specific to the hardware on a line card, use the attach command in
privileged EXEC mode to connect to the line card and then use the show controllers command in
privileged EXEC mode or the execute-on command in privileged EXEC mode.
show controllers atm [[port-number] [all | sar | summary]]
show controllers fia [register]
show controllers {frfab | tofab} {bma {microcode | ms-inst | register} | qelem
start-queue-element [end-queue-element] | qnum start-queue-number [end-queue-number] |
queues | statistics}
show controllers io
show controllers l3
show controllers pos {framers | queues | registers | rxsram port-number queue-start-address
[queue-length] | txsram port-number queue-start-address [queue-length]}
show controllers events [clear | punt-sniff [none | word1 | word2] | punt-verbose [all]]

Syntax Description

atm

Displays the ATM controller information.

port-number

(Optional) Displays request for the physical interface on the

ATM card. The range of choices is from 0 to 3.

all

(Optional) Lists all details.

sar

(Optional) Lists SAR interactive command.

summary

(Optional) Lists SAR status summary.

fia

Displays the fabric interface ASIC information.

register

(Optional) Displays the register information.

frfab

(Optional) Displays the "from" (transmit) fabric information.

tofab

(Optional) Displays the "to" (receive) fabric information.

bma

For the frfab or tofab keywords, displays microcode, micro

sequencer, or register information for the silicon queuing
engine (SQE), also known as the buffer management ASIC
(BMA).

microcode

Displays SQE information for the microcode bundled in the

line card and currently running version.

mis-inst

Displays SQE information for the micro sequencer instruction.

register

Displays silicon queuing engine (SQE) information for the

register.

qelem

For the frfab or tofab keywords, displays the SDRAM buffer

pool queue element summary information.

start-queue-element

Specifies the start queue element number from 0 to 65535.

end-queue-element

(Optional) Specifies the end queue element number from

0 to 65535).

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-639

show controllers (line card image)

qnum

For the frfab or tofab keywords, displays the SDRAM buffer

pool queue detail information.

start-queue-number

Specifies the start free queue number (from 0 to 127).

end-queue-number

(Optional) Specifies the end free queue number (from 0 to

127).

queues

For the frfab or tofab keywords, displays the SDRAM buffer

pool information.

statistics

For the frfab or tofab keywords, displays the BMA counters.

io

Displays input/output registers.

l3

Displays Layer 3 ASIC information.

pos

Displays packet-over-sonic (POS) information for framer

registers, framer queues, and ASIC registers.

framers

Displays the POS framer registers.

queues

Displays the POS framer queue information.

registers

Displays the ASIC registers.

rxsram

Displays the receive queue SRAM.

port-number

Specifies a port number (valid range is from 0 to 3).

queue-start-address

Specifies the queue SRAM logical starting address.

queue-length

(Optional) Specifies the queue SRAM length.

txsram

Displays the transmit queue SRAM.

events

Displays the line card counter information of events generated

from line card.

clear

(Optional) Clears all the line card event counter output details
that are displayed using the commands: show controllers
events, show controllers events punt-verbose, and show
controllers events punt-sniff.

punt-sniff

(Optional) Sniffs the packets sent to route processor from line

card by specifying the word and location.

Note

Punt sniff is enabled only if one of the word is

configured.

none

(Optional) Clears the attributes and packets to be sniffed from

route processor and resets the counters to zero.

word1

(Optional) Sniffs packets sent to the route processor for the

specified hexa decimal value of word1. Location of the word is
optional.

word2

(Optional) Sniffs packets sent to the route processor matching

the specified hexa decimal value of word2. Location of the
word is optional.

punt-verbose

(Optional) Displays application-wise packets punt to route

processor (RP) from line card (LC). Displays non-zero punt
counters if the command is executed without the all keyword.

all

(Optional) Displays zero and non-zero punt counters of

packets punt to RP from LC. The all keyword is used along
with the command show controllers events punt-verbose all.

Cisco IOS Configuration Fundamentals Command Reference

CF-640

April 2010

show controllers (line card image)

Command Modes

Privileged EXEC

Command History

Release

Modification

11.2 GS

This command was added to support the Cisco 12000 series Gigabit Switch
Routers.

Usage Guidelines

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(31)SB

This command was integrated in Cisco IOS Release 12.2(31)SB.

12.2(33)SB

This command behavior was modified on the Cisco 10000 series router for
the PRE3 and PRE4.

12.0(33)S

The keywords punt-sniff and punt-verbose were added in the command

show controllers events for the Cisco 12000 Series Routers.

This information displayed by this command is of use only to technical support representatives in
analyzing unexpected system failures in the field. It is documented here in case you need to provide the
displayed statistics to an technical support engineer.
Cisco 10000 Series Router Usage Guidelines

In releases prior to Cisco IOS Release 12.2(33)SB, when you configure the t1 loopback remote
command on the local router, the command also displays in the running-config file of the far-end router.
This is due to the route processor (RP) updating an incorrect parameter when it receives the loopback
event message from the line card for loopback requests from the far end.
In Cisco IOS Release 12.2(33)SB, the RP updates the correct parameter and the show controllers
command correctly displays the loopback CLI commands applied on the local end and displays the
loopback events and status received from the line card in response to loopback requests from the far end.
This change in behavior affects the following line cards and is documented in the CSCsm84447 caveat:

4-port channelized STM1

1-port channelized OC-12

6-port channelized T3

4-port half-height channelized T3

In Cisco IOS Release 12.2(33)SB, the output from the show controller command includes line code
information for the 6-port channelized T3 line card and the 8-port E3/DS3 line card. However, because
SONET line cards do not have a direct physical link at the T3 or E3 level, the output from the
show controller t3 command does not include line code information.
In Cisco IOS Release 12.2(31)SB, the output from the show controller command displays line code
information. The output of the show controller t3 command for SONET-based T3 also includes line
code information.
Cisco 12000 Series Router Usage Guidelines

The packets processed by a line card are either sent to a route processor or a line card in the form of
Cisco cells. To track the packets sent to a route processor from a line card is essential for troubleshooting.
The keywords punt-sniff and punt-verbose have been added for the command show controllers events
to identify the packets sent to RP from LC.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-641

show controllers (line card image)

By default, the feature is enabled and packets punt to route processor are displayed using the command
show controllers events punt-verbose. To view all the zero and non-zero punt counters use the
command show controllers events punt-verbose all.
To clear all the line card events and counters including resetting the packets to be sniffed to zero,
executing the command show controllers events clear.
Packets sent to route processor from line card can be sniffed by specifying the hexa-decimal value of the
word. Packets can only be sniffed if the word along with the hexa-decimal value is specified. Specifying
the location of the word, sniffs packets from the particular location. To reset the counters of packets to
be sniffed to zero, execute the command show controllers events punt-sniff none.
For example, use the command show controllers events punt-sniff word1 0x60000000 to sniff packets
punt to RP with the hexa-decimal value 0x60000000. As the location is not specified, it searches the
entire buffer for the value 0x60000000. Packets punt to RP can also be sniffed by specifying a particular
location using the command show controllers events punt-sniff word1 0x60000000 34.

Examples

Because you are executing this command on the line card, you must use the execute-on command to use
the show command, or you must connect to the card using the attach command. All examples in this
section use the execute-on command
The following is partial sample output from the show controllers atm command:
Router# execute-on slot 4 show controllers atm 0
TX SAR (Beta 1.0.0) is Operational;
RX SAR (Beta 1.0.0) is Operational;
Interface Configuration Mode:
STS-12c
Active Maker Channels: total # 6
VCID ChnnlID Type OutputInfo
1
0888
UBR
0C010010
2
0988
VBR
04010020
3
8BC8
UBR
0C010030
4
0E08
UBR
0C010040
10
1288
VBR
040100A0
11
8BE8
VBR
0C0100B0

InPkts
0
0
0
0
0
0

InOAMs
0
0
0
0
0
0

MacString
08882000AAAA030000000800
09882000
8BC82000AAAA030000000800
0E082000AAAA030000000800
12882000
8BE82000AAAA030000000800

SAR Total Counters:

total_tx_idle_cells 215267 total_tx_paks 0 total_tx_abort_paks 0
total_rx_paks 0 total_rx_drop_paks 0 total_rx_discard_cells 15
Switching Code Counters:
total_rx_crc_err_paks 0 total_rx_giant_paks 0
total_rx_abort_paks 0 total_rx_crc10_cells 0
total_rx_tmout_paks 0 total_rx_unknown_paks 0
total_rx_out_buf_paks 0 total_rx_unknown_vc_paks 0
BATMAN Asic Register Values:
hi_addr_reg 0x8000, lo_addr_reg 0x000C, boot_msk_addr 0x0780,
rmcell_msk_addr 0x0724, rmcnt__msk_addr 0x07C2, txbuf_msk_addr 0x070C,
.
.
.
CM622 SAR Boot Configuration:
txind_q_addr 0x14000 txcmd_q_addr 0x20000
.
.
.
SUNI-622 Framer Register Values:

Cisco IOS Configuration Fundamentals Command Reference

CF-642

April 2010

show controllers (line card image)

Master Rst and Ident/Load Meters Reg (#0x0): 0x10

Master Configuration Reg (#0x1): 0x1F
Master Interrupt Status Reg (#0x2): 0x00
PISO Interrupt Reg (#0x3): 0x04
Master Auto Alarm Reg (#0x4): 0x03
Master Auto Alarm Reg (#0x5): 0x07
Parallel Output Port Reg (#0x6): 0x02
.
.
.
BERM Line BIP Threshold LSB Reg (#0x74): 0x00
BERM Line BIP Threshold MSB Reg (#0x75): 0x00
Router#

The following is partial sample output from the show controllers command:
Router# execute-on slot 6 show controllers
Interface POS0
Hardware is BFLC POS
lcpos_instance struct
60311B40
RX POS ASIC addr space 12000000
TX POS ASIC addr space 12000100
SUNI framer addr space 12000400
SUNI rsop intr status
00
CRC32 enabled, HDLC enc, int clock
no loop
Interface POS1
Hardware is BFLC POS
lcpos_instance struct
603142E0
RX POS ASIC addr space 12000000
TX POS ASIC addr space 12000100
SUNI framer addr space 12000600
SUNI rsop intr status
00
CRC32 enabled, HDLC enc, int clock
no loop
.
.
.
Router#

The following is partial sample output from the show controllers pos framers command:
Router# execute-on slot 6 show controllers pos framers
Framer 0, addr=0x12000400:
master reset
C0
master config
1F
master control
00
clock rcv cntrl
D0
RACP control
84
RACP gfc control
0F
TACP control status
04
RACP intr enable
04
RSOP cntrl intr enable 00
RSOP intr status
00
TPOP path sig lbl (c2) 13
SPTB control
04
SPTB status
00
Framer 1, addr=0x12000600:
master reset
C0
master config
1F

rrate sts3c trate sts3c fixptr

hcsadd

tnull

rrate sts3c trate sts3c fixptr

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-643

show controllers (line card image)

master control
clock rcv cntrl
RACP control
RACP gfc control
TACP control status
RACP intr enable
RSOP cntrl intr enable
RSOP intr status
TPOP path sig lbl (c2)
SPTB control
SPTB status

00
D0
84
0F
04
04
00
00
13
04
00

Framer 2, addr=0x12000800:
master reset
C0
master config
1F
master control
00
clock rcv cntrl
D0
RACP control
84
RACP gfc control
0F
TACP control status
04
RACP intr enable
04
RSOP cntrl intr enable 00
RSOP intr status
00
TPOP path sig lbl (c2) 13
SPTB control
04
SPTB status
00
.
.
.
Router#

hcsadd

tnull

rrate sts3c trate sts3c fixptr

hcsadd

tnull

The following is partial sample output from the show controllers fia command:
Router# execute-on slot 7 show controllers fia
========= Line Card (Slot 7) =======
Fabric configuration: Full bandwidth redundant
Master Scheduler: Slot 17
From Fabric FIA Errors
----------------------redund fifo parity 0
crc32 lkup parity 0
0
1
--------------los
0
0
crc16 0
0
To Fabric FIA Errors
----------------------sca not pres 0
grant parity 0
cntrl parity 0
multi fifo
0

redund overflow 0
cell parity
0
2
3
--------------0
0
0
0

req error
multi req
uni req
empty dst req

0
0
0
0

cell drops 0
crc32
0
4
-------0
0

uni fifo overflow

uni fifo undrflow
crc32 lkup parity
handshake error

0
0
0
0

The following is a sample output from the show controllers events command:
Router# execute-on slot 7 show controllers events
Switching Stats
Packets punt to RP: 935
HW engine punt: 62
HW engine reject: 38113520

Cisco IOS Configuration Fundamentals Command Reference

CF-644

April 2010

show controllers (line card image)

RX HW Engine Reject Counters

Unrecognized Protocol ID: 19182546
IP TTL Expired: 14706652
Unrecognized L2 Frame: 4224320
IPv6 Control pkts: 2

The following is a sample output from the show controllers events punt-verbose command:
Router# execute-on slot 7 show controllers events punt-verbose
RP Punted L2 Statistics in Verbose
-----------------------------------HDLC Encap
: 927
RP Punted L3 Statistics in Verbose
-----------------------------------ICMP
: 40
UDP
: 441
OSPF
: 211
IPV6
: 40
RP Punted L3 Application Statistics in Verbose
----------------------------------------------LDP
: 441
DF Bit not Set
: 692

The following is a partial sample output from the show controllers events punt-verbose all command
which displays the zero and non-zero value of packets punt to RP from LC:
Router# execute-on slot 7 show controllers events punt-verbose all
RP Punted L2 Statistics in Verbose
-----------------------------------L2 Protocol - 0
: 0
ARPA Encap
: 0
L2 Protocol - 2
: 0
L2 Protocol - 3
: 0
L2 Protocol - 4
: 0
HDLC Encap
: 941
L2 Protocol - 6
: 0
L2 Protocol - 7
: 0
L2 Protocol - 8
: 0
L2 Protocol - 9
: 0
L2 Protocol - 10
: 0
L2 Protocol - 11
: 0
L2 Protocol - 12
: 0
L2 Protocol - 13
: 0
L2 Protocol - 14
: 0
L2 Protocol - 15
: 0
PPP Encap
: 0
L2 Protocol - 17
: 0
L2 Protocol - 18
: 0
L2 Protocol - 19
: 0
Frame Relay Encap
: 0
L2 Protocol - 21
: 0
L2 Protocol - 22
: 0
L2 Protocol - 23
: 0
L2 Protocol - 24
: 0
L2 Protocol - 25
: 0
L2 Protocol - 26
: 0
L2 Protocol - 27
: 0
L2 Protocol - 28
: 0
L2 Protocol - 29
: 0

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-645

show controllers (line card image)

L2 Protocol
L2 Protocol
L2 Protocol
ATM Encap
L2 Protocol
L2 Protocol

- 30
- 31
- 32
- 34
- 35

:
:
:
:
:
:

0
0
0
0
0
0

RP Punted L3 Statistics in Verbose

-----------------------------------HOPOPT
: 0
ICMP
: 40
IGMP
: 0
L3 Protocol - 3
: 0
IPINIP
: 0
L3 Protocol - 5
: 0
RP Punted L3 Application Statistics in Verbose
----------------------------------------------MPLS OAM
: 0
FTP
: 0
FTPD
: 0
TFTP
: 0
.....

The following is a sample output from the show controllers events clear command:
Router# execute-on slot 7 show controllers events clear
Drop, switching and reject counters cleared

The following is a sample output from the show controllers events punt-sniff command:
Router# execute-on slot 7 show controllers events punt-sniff
Punt Sniff Statistics
-------------------------------Word
Location
Occurance
0x60000000
34
0
0xB6010102
37
5
Note: Location offset taken from the begining of BufferHeader(32 bytes).

The following is a sample output from the show controllers events punt-sniff word1 0x60000000
command. This command is used to sniff a packet with a hexa-decimal value 0x60000000 from the start
of the buffer header of the packet being punt to RP:
Router# execute-on slot 7 show controllers events punt-sniff word1 0x60000000

The following is a sample output from the show controllers events punt-sniff word1 0x60000000 34
command. This command is used to sniff a packet with a hexa-decimal value 0x60000000 0 at the
location 34 from the start of the buffer header of the packet being punt to RP:
Router# execute-on slot 7 show controllers events punt-sniff word1 0x60000000 34

The following is a sample output from the show controllers events punt-sniff none command. This
command is used to clear the counter of packets to be sniffed:
Router# execute-on slot 7 show controllers events punt-sniff none

Related Commands

Command

Description

clear controllers

Resets the T1 or E1 controller.

Cisco IOS Configuration Fundamentals Command Reference

CF-646

April 2010

show controllers logging

show controllers logging

To display logging information about a Versatile Interface Processor (VIP) card, use the show
controllers logging command in privileged EXEC mode.
show controllers vip slot-number logging

Syntax Description

vip slot-number

Command Modes

Privileged EXEC

Command History

Release

Usage Guidelines

VIP slot number.

Modification

11.2

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

This command displays the state of syslog error and event logging, including host addresses, and
whether console logging is enabled.
When enabled, trap logging allows messages to be sent to a remote host (a syslog server).

Examples

The following is sample output from the show controllers logging command:
Router# show controllers vip 1 logging
show logging from Slot 1:
Syslog logging:enabled (0 messages dropped, 1 messages rate-limited, 0 flushes, 0
overruns)
Console logging: disabled
Monitor logging: level debugging, 0 messages logged
Buffer logging: level debugging, 24 messages logged
Trap logging: level informational, 266 messages logged.
Logging to 209.165.202.129
Exception Logging size: 4096 bytes
Count and timestamp logging messages:disabled
Log Buffer (8192 bytes):
smallest_local_pool_entries = 256, global particles = 5149
highest_local_visible_bandwidth = 155000
00:00:05:%SYS-5-RESTART:System restarted -.
.
.

Table 67 describes the significant fields shown in the display.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-647

show controllers logging

Table 67

show controllers logging Field Descriptions

Field

Description

Syslog logging

Shows general state of system logging (enabled or disabled), and status of

logged messages (number of messages dropped, rate-limited, or flushed).

Console logging

Logging to the console port. Shows "disabled" or, if enabled, the severity level
limit and number of messages logged.
Enabled using the logging console command.

Monitor logging

Logging to the monitor (all TTY lines). Shows "disabled" or, if enabled, the
severity level limit and number of messages logged.
Enabled using the logging monitor command.

Buffer logging

Logging to the standard syslog buffer. Shows "disabled" or, if enabled, the
severity level limit and number of messages logged.
Enabled using the logging buffered command.

Trap logging

Logging to a remote host (syslog host). Shows "disabled" or, if enabled, the
severity level limit and number of messages logged.
(The word "trap" means a trigger in the system software for sending error
messages to a remote host.)
Enabled using the logging host command. The severity level limit is set using
the logging trap command.

Related Commands

Command

Description

show logging

Displays the state of logging (syslog).

Cisco IOS Configuration Fundamentals Command Reference

CF-648

April 2010

show controllers tech-support

show controllers tech-support

To display general information about a Versatile Interface Processor (VIP) card when reporting a
problem, use the show controllers tech-support command in privileged EXEC mode.
show controllers vip slot-number tech-support

Syntax Description

vip slot-number

Command Modes

Privileged EXEC

Command History

Release

Usage Guidelines

VIP slot number.

Modification

11.2

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Use this command to help collect general information about a VIP card when you are reporting a
problem. This command displays the equivalent of the following show commands for the VIP card:

more system:running-config

show buffers

show controllers

show interfaces

show processes cpu

show processes memory

show stacks

show version

For a sample display of the show controllers tech-support command output, refer to these show
commands.

Related Commands

Command

Description

more
system:running-config

Displays the running configuration.

show buffers

Displays statistics for the buffer pools on the network server.

show controllers

Displays information that is specific to the hardware.

show interfaces

Uses the show interfaces EXEC command to display ALC information.

show processes

Displays information about the active processes.

show processes
memory

Displays memory used.

show stacks

Monitors the stack usage of processes and interrupt routines.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-649

show controllers tech-support

Command

Description

show tech-support

Displays general information about the router when reporting a problem.

show version

Displays the configuration of the system hardware, the software version,

the names and sources of configuration files, and the boot images.

Cisco IOS Configuration Fundamentals Command Reference

CF-650

April 2010

show coverage history

show coverage history

To display the system history table, use the show coverage history command in privileged EXEC mode.
show coverage history [all | first number-of-entries | last number-of-entries | status]

Syntax Description

all

(Optional) Displays the entire history table.

first

(Optional) Displays the oldest entries in the history table.

number-of-entries

(Optional) Number of entries to be displayed. The range is from 1 to 100000.

last

(Optional) Displays the latest entries in the history table.

status

(Optional) Displays the status of the history system.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.4(24)T

This command was introduced in a release earlier than Cisco IOS

Release 12.4(24)T.

Examples

The following is sample output from the show coverage history command. The output is
self-explanatory.
Router# show coverage history status
History table size is 23 entries. 0 entries have been used.
Low-level count handler has been called 0 times.
There were 0 entries not traced due to recursion detection.
There were 0 entries not traced due to internal pauses.

Related Commands

Command

Description

coverage history

Enables the system to record the history of the events.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-651

show data-corruption

show data-corruption
To display data inconsistency errors of the present software version, use the show data-corruption
command in user EXEC or privileged EXEC mode.
show data-corruption

Syntax Description

This command has no arguments or keywords.

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History

Release

Modification

12.2(22)SE

This command was introduced.

12.2(33)SRB

This command was integrated into Cisco IOS Release 12.2(33)SRB.

12.4(20)T

This command was integrated into Cisco IOS Release 12.4(20)T.

12.2(33)SXI

This command was integrated into Cisco IOS Release 12.2(33)SXI.

Cisco IOS 2.3 XE

This command was integrated into Cisco IOS XE Release 2.3.

Usage Guidelines

Use this command to display all data inconsistency errors or the corrupt data. If there are no data errors,
the No data inconsistency errors have been recorded message is displayed.

Examples

The following is sample output from show data-corruption command. The fields are self-explanatory.
Router# show data-corruption
Data inconsistency records for:
3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T, RELEASE
SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Compiled Thu 17-Dec-09 09:02 by xyz
Count
1842

Traceback
60523C58, 616E85FC 60523C58 62A9F648
1: Jun 12 18:24:33.960
2: Jun 12 18:24:33.960
3: Jun 12 18:24:33.960
1842: Jun 19 00:30:51.350

Cisco IOS Configuration Fundamentals Command Reference

CF-652

April 2010

show debugging

show debugging
To display information about the types of debugging that are enabled for your router, use the
show debugging command in privileged EXEC mode.
show debugging

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

11.1

This command was introduced.

12.3(7)T

The output of this command was enhanced to show TCP Explicit Congestion
Notification (ECN) configuration.

Examples

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(31)SB2

This command was integrated into Cisco IOS Release 12.2(31)SB2.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support
in a specific 12.2SX release of this train depends on your feature set,
platform, and platform hardware.

12.4(20)T

The output of this command was enhanced to show the user-group debugging
configuration.

The following is sample output from the show debugging command. In this example, the remote host is
not configured or connected.
Router# show debugging
!
TCP:
TCP Packet debugging is on
TCP ECN debugging is on
!
Router# telnet 10.1.25.234
!
Trying 10.1.25.234 ...
!
00:02:48: 10.1.25.31:11001 <---> 10.1.25.234:23 out ECN-setup SYN
00:02:48: tcp0: O CLOSED 10.1.25.234:11001 10.1.25.31:23 seq 1922220018
OPTS 4 ECE CWR SYN WIN 4128
00:02:50: 10.1.25.31:11001 <---> 10.1.25.234:23 congestion window changes
00:02:50: cwnd from 1460 to 1460, ssthresh from 65535 to 2920
00:02:50: tcp0: R SYNSENT 10.1.25.234:11001 10.1.25.31:23 seq 1922220018
OPTS 4 ECE CWR SYN WIN 4128
00:02:54: 10.1.25.31:11001 <---> 10.1.25.234:23 congestion window changes
00:02:54: cwnd from 1460 to 1460, ssthresh from 2920 to 2920
00:02:54: tcp0: R SYNSENT 10.1.25.234:11001 10.1.25.31:23 seq 1922220018
OPTS 4 ECE CWR SYN WIN 4128
00:03:02: 10.1.25.31:11001 <---> 10.1.25.234:23 congestion window changes
00:03:02: cwnd from 1460 to 1460, ssthresh from 2920 to 2920

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-653

show debugging

00:03:02: tcp0: R SYNSENT 10.1.25.234:11001 10.1.25.31:23 seq 1922220018

OPTS 4 ECE CWR SYN WIN 4128
00:03:18: 10.1.25.31:11001 <---> 10.1.25.234:23 SYN with ECN disabled
00:03:18: 10.1.25.31:11001 <---> 10.1.25.234:23 congestion window changes
00:03:18: cwnd from 1460 to 1460, ssthresh from 2920 to 2920
00:03:18: tcp0: O SYNSENT 10.1.25.234:11001 10.1.25.31:23 seq 1922220018
OPTS 4 SYN WIN 4128
00:03:20: 10.1.25.31:11001 <---> 10.1.25.234:23 congestion window changes
00:03:20: cwnd from 1460 to 1460, ssthresh from 2920 to 2920
00:03:20: tcp0: R SYNSENT 10.1.25.234:11001 10.1.25.31:23 seq 1922220018
OPTS 4 SYN WIN 4128
00:03:24: 10.1.25.31:11001 <---> 10.1.25.234:23 congestion window changes
00:03:24: cwnd from 1460 to 1460, ssthresh from 2920 to 2920
00:03:24: tcp0: R SYNSENT 10.1.25.234:11001 10.1.25.31:23 seq 1922220018
OPTS 4 SYN WIN 4128
00:03:32: 10.1.25.31:11001 <---> 10.1.25.234:23 congestion window changes
00:03:32: cwnd from 1460 to 1460, ssthresh from 2920 to 2920
00:03:32: tcp0: R SYNSENT 10.1.25.234:11001 10.1.25.31:23 seq 1922220018
OPTS 4 SYN WIN 4128
!Connection timed out; remote host not responding

The following is sample output from the show debugging command when user-group debugging is
configured:
Router# show debugging
!
usergroup:
Usergroup Deletions debugging is on
Usergroup Additions debugging is on
Usergroup Database debugging is on
Usergroup API debugging is on
!

Table 68 describes the significant fields in the output.

Table 68

show debugging Field Descriptions

Field

Description

OPTS 4

Bytes of TCP expressed as a number. In this case, the bytes are 4.

ECE

Echo congestion experience.

CWR

Congestion window reduced.

SYN

Synchronize connectionsRequest to synchronize sequence

numbers, used when a TCP connection is being opened.

WIN 4128

Advertised window size, in bytes. In this case, the bytes are 4128.

cwnd

Congestion window (cwnd)Indicates that the window size has

changed.

ssthresh

Slow-start threshold (ssthresh)Variable used by TCP to determine

whether or not to use slow-start or congestion avoidance.

usergroup

Statically defined usergroup to which source IP addresses are

associated.

Cisco IOS Configuration Fundamentals Command Reference

CF-654

April 2010

show declassify

show declassify
To display the state of the declassify function (enabled, in progress, and so forth) and the sequence of
declassification steps that will be performed, use the show declassify command in global configuration
mode.
show declassify

Syntax Description

Note

This command has no arguments or keywords.

The show declassify command is supported on the Cisco 3200 series routers only.

Command Modes

Global configuration

Command History

Release

Examples

Modification

12.3(8)YD

This command was introduced.

12.4(2)T

This command was integrated into Cisco IOS Release 12.4(2)T.

The following example is sample output for the show declassify command:
Router# show declassify
Declassify facility: Enabled=Yes In Progress=No
Erase flash=Yes Erase nvram=Yes
Obtain memory size
Shutdown Interfaces
Declassify Console and Aux Ports
Erase flash
Declassify NVRAM
Declassify Communications Processor Module
Declassify RAM, D-Cache, and I-Cache

Table 69 describes the significant fields shown in the display.

Table 69

show declassify Field Descriptions

Field

Description

Enabled

A Yes value indicates that zeroization is enabled.

A No value indicates that zeroization is disabled.

In Progress

A Yes value indicates that zeroization is currently in

progress.
A No value indicates that zeroization is currently not in
progress.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-655

show declassify

Table 69

show declassify Field Descriptions (continued)

Field

Description

Erase flash

A Yes value indicates that erasure of Flash memory is

enabled.
A No value indicates that the erasure of Flash memory is
disabled.

Erase nvram

A Yes value indicates that the erasure of NVRAM is

enabled.
A No value indicates that the erasure of NVRAM is
disabled.

Obtain memory size

Obtain the main memory size in order to understand how

much of the memory is to be scrubbed.

Shutdown Interfaces

Shut down any and all network interfaces.

Declassify Console and AUX Ports

Remove potentially sensitive information from console and

AUX port FIFOs.

Erase flash

Erase Flash memory.

Declassify NVRAM

Erase NVRAM.

Declassify Communications Processor Erase the memory in the Communications Processor Module
Module
(CPM).
Declassify RAM, D-Cache, and
I-Cache

Related Commands

Scrub the main memory, erase the Data Cache (D-Cache),

and erase the Instruction Cache (I-Cache).

Command

Description

service declassify

Invokes declassification.

Cisco IOS Configuration Fundamentals Command Reference

CF-656

April 2010

show derived-config

show derived-config
To display the composite results of all the configuration commands that apply to an interface, including
commands that come from sources such as static templates, dynamic templates, dialer interfaces, and
authentication, authorization, and accounting (AAA) per-user attributes, use the show derived-config
command in privileged EXEC mode.
show derived-config [interface type number]

Syntax Description

interface type number

Command Modes

Privileged EXEC

Command History

Release

Modification

12.1

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

(Optional) Displays the derived configuration for a specific interface. If you

use the interface keyword, you must specify the interface type and the
interface number (for example, interface ethernet 0).

Configuration commands can be applied to an interface from sources such as static templates, dynamic
templates bound by resource pooling, dialer interfaces, AAA per-user attributes and the configuration of
the physical interface. The show derived-config command displays all the commands that apply to an
interface.
The output for the show derived-config command is nearly identical to that of the show running-config
command. It differs when the configuration for an interface is derived from a template, a dialer interface,
or some per-user configuration. In those cases, the commands derived from the template, dialer
interface, and so on, will be displayed for the affected interface.
If the same command is configured differently in two different sources that apply to the same interface,
the command coming from the source that has the highest precedence will appear in the display.

Examples

The following examples show sample output for the show running-config and show derived-config
commands for serial interface 0:23 and dialer interface 0. The output of the show running-config and
show derived-config commands is the same for dialer interface 0 because none of the commands that
apply to that interface are derived from any sources other than the configuration of the dialer interface.
The output for the show running-config and show derived-config commands for serial interface 0:23
differs because some of the commands that apply to serial interface 0:23 come from dialer interface 0.
Router# show running-config interface Serial0:23
Building configuration...
Current configuration :296 bytes
!
interface Serial0:23
description PRI to ADTRAN (#4444150)

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-657

show derived-config

ip unnumbered Loopback0
encapsulation ppp
dialer rotary-group 0
isdn switch-type primary-dms100
isdn incoming-voice modem
isdn calling-number 4444150
peer default ip address pool old_pool
end
Router# show running-config interface Dialer0
Building configuration...
Current configuration :257 bytes
!
interface Dialer0
description Dialin Users
ip unnumbered Loopback0
no ip proxy-arp
encapsulation ppp
dialer in-band
dialer idle-timeout 30
dialer-group 1
peer default ip address pool new_pool
ppp authentication pap chap callin
end
Router# show derived-config interface Serial0:23
Building configuration...
Derived configuration :332 bytes
!
interface Serial0:23
description PRI to ADTRAN (#4444150)
ip unnumbered Loopback0
encapsulation ppp
dialer rotary-group 0
isdn switch-type primary-dms100
isdn incoming-voice modem
isdn calling-number 4444150
peer default ip address pool new_pool
ppp authentication pap chap callin
end
Router# show derived-config interface Dialer0
Building configuration...
Derived configuration :257 bytes
!
interface Dialer0
description Dialin Users
ip unnumbered Loopback0
no ip proxy-arp
encapsulation ppp
dialer in-band
dialer idle-timeout 30
dialer-group 1
peer default ip address pool new_pool
ppp authentication pap chap callin
end

Cisco IOS Configuration Fundamentals Command Reference

CF-658

April 2010

show derived-config

Related Commands

Command

Description

show running-config

Displays the contents of the currently running configuration file or the

configuration for a specific interface.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-659

show diagnostic cns

show diagnostic cns

To display the information about the CNS subject, use the show diagnostic cns command in user EXEC
or privileged EXEC mode.
show diagnostic cns {publish | subscribe}

Syntax Description

publish

Displays the subject with which the diagnostic results is published.

subscribe

Displays the subscribed subjects.

Defaults

This command has no default settings.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

This command is not supported on Cisco 7600 series routers that are configured with a Supervisor
Engine 2.
The CNS subsystem communicates with remote network applications through the CNS-event agent and
follows the publish and subscribe model. An application sets itself up to receive events by subscribing
to the approprate event subject name.

Examples

This example shows how to display the subject with which the diagnostic results is published:
Router# show diagnostic cns publish
Subject: cisco.cns.device.diag_results

This example shows how to display the subscribed subject:

Router# show diagnostic cns subscribe
Subject: cisco.cns.device.diag_get_results

Related Commands

Command

Description

diagnostic cns

Configures the CNS diagnostics.

Cisco IOS Configuration Fundamentals Command Reference

CF-660

April 2010

show diagnostic sanity

show diagnostic sanity

To display sanity check results, use the show diagnostic sanity command in privileged EXEC mode.
show diagnostic sanity

Syntax Description

This command has no arguments or keywords.

Defaults

Displays information for all the Gigabit Ethernet WAN interfaces in the Cisco 7600 series router.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.2(18)SXE

Support for this command was introduced on the Supervisor Engine 720.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The sanity check runs a set of predetermined checks on the configuration with a possible combination
of certain system states to compile a list of warning conditions. The checks are designed to look for
anything that seems out of place and are intended to serve as an aid to maintaining the system sanity.
The following is a list of the checks that are run and the action taken when the condition is found:

Checks whether the default gateways are reachable. If so, the system stops pinging.

If a port auto-negotiates to half duplex, the system flags it.

Trunking Checks

If a trunk port has the mode set to on, the system flags it.

If a port is trunking and mode is auto, the system flags it.

If a trunk port is not trunking and the mode is desirable, the system flags it.

If a trunk port negotiates to half duplex, the system flags it.

Channeling Checks

If a port has channeling mode set to on, the system flags it.

If a port is not channeling and the mode is set to desirable, the system flags it.

If a VLAN has a Spanning-Tree root of 32K (root is not set), the system flags it.

Spanning-Tree VLAN Checks

If a VLAN has a max age on the Spanning-Tree root that is different than the default, the system
flags it.

If a VLAN has a fwd delay on the Spanning-Tree root that is different than the default, the system
flags it.

If a VLAN has a fwd delay on the bridge that is different than the default, the system flags it.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-661

show diagnostic sanity

If a VLAN has a fwd delay on the bridge that is different than the default, the system flags it.

If a VLAN has a hello time on the bridge that is different than the default, the system flags it.

Spanning-Tree Port Checks

If a port has a port cost that is different than the default, the system flags it.

If a port has a port priority that is different than the default, the system flags it.

UDLD Checks

If a port has UDLD disabled, the system flags it.

If a port had UDLD shut down, the system flags it.

If a port had a UDLD undetermined state, the system flags it.

Assorted Port Checks

If a port had receive flow control disabled, the system flags it.

If a trunk port had PortFast enabled, the system flags it.

If a inline power port has any of the following states:

denied
faulty
other
off

The system flags it.

If a port has a native VLAN mismatch, the system flags it.

If a port has a duplex mismatch, the system flags it.

Bootstring and Config Register Checks

The config register on the primary supervisor engine (and on the secondary supervisor engine if
present) must be one of the following values: 0x2 , 0x102, or 0x2102.

The system verifies the bootstring on the primary supervisor engine (and on the secondary
supervisor engine if present). The system displays a message if the bootstring is empty.

The system verifies that every file is specified in the bootstring. The system displays a message if
the file is absent or shows up with a wrong checksum.
If only device: is specified as a filename, then the system verifies that the first file is on the device.

Assorted Checks

The system displays a message if IGMP snooping is disabled.

The system displays a message if any of the values of the snmp community access strings
{RO,RW,RW-ALL} is the same as the default.

The system displays a message if any of the modules are in states other than Ok.

The system displays a message that lists all the tests that failed (displayed as an F) in the show
test all command.

The system displays a message if *fast is not configured on the switch anywhere.

The system displays a message if there is enough room for the crashinfo file on the bootflash:.

The system displays a message if multicast routing is enabled globally but is not applied to all
interfaces.

Cisco IOS Configuration Fundamentals Command Reference

CF-662

April 2010

show diagnostic sanity

Examples

The system displays a message if IGMP snooping is disabled and RGMP is enabled.

This example displays samples of the messages that could be displayed with the show diagnostic sanity
command:
Router# show diagnostic sanity
Pinging default gateway 10.6.141.1 ....
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.6.141.1, timeout is 2 seconds:
..!!.
Success rate is 0 percent (0/5)
IGMP snooping disabled please enable it for optimum config.
IGMP snooping disabled but RGMP enabled on the following interfaces,
please enable IGMP for proper config :
Vlan1, Vlan2, GigabitEthernet1/1
Multicast routing is enabled globally but not enabled on the following
interfaces:
GigabitEthernet1/1, GigabitEthernet1/2
A programming algorithm mismatch was found on the device bootflash:
Formatting the device is recommended.
The bootflash: does not have enough free space to accomodate the crashinfo file.
Please check your confreg value : 0x0.
Please check your confreg value on standby: 0x0.
The boot string is empty. Please enter a valid boot string .
Could not verify boot image "disk0:" specified in the boot string on the
slave.
Invalid boot image "bootflash:asdasd" specified in the boot string on the
slave.
Please check your boot string on the slave.
UDLD has been disabled globally - port-level UDLD sanity checks are
being bypassed.
OR
[
The following ports have UDLD disabled. Please enable UDLD for optimum
config:
Fa9/45
The following ports have an unknown UDLD link state. Please enable UDLD
on both sides of the link:
Fa9/45
]
The following ports have portfast enabled:
Fa9/35, Fa9/45
The following ports have trunk mode set to on:
Fa4/1, Fa4/13
The following trunks have mode set to auto:
Fa4/2, Fa4/3

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-663

show diagnostic sanity

The following ports with mode set to desirable are not trunking:
Fa4/3, Fa4/4
The following trunk ports have negotiated to half-duplex:
Fa4/3, Fa4/4
The following ports are configured for channel mode on:
Fa4/1, Fa4/2, Fa4/3, Fa4/4
The following ports, not channeling are configured for channel mode
desirable:
Fa4/14
The following vlan(s) have a spanning tree root of 32768:
1
The following vlan(s) have max age on the spanning tree root different from
the default:
1-2
The following vlan(s) have forward delay on the spanning tree root different
from the default:
1-2
The following vlan(s) have hello time on the spanning tree root different
from the default:
1-2
The following vlan(s) have max age on the bridge different from the
default:
1-2
The following vlan(s) have fwd delay on the bridge different from the
default:
1-2
The following vlan(s) have hello time on the bridge different from the
default:
1-2
The following vlan(s) have a different port priority than the default
on the port FastEthernet4/1
1-2
The following ports have recieve flow control disabled:
Fa9/35, Fa9/45
The following inline power ports have power-deny/faulty status:
Gi7/1, Gi7/2
The following ports have negotiated to half-duplex:
Fa9/45
The following vlans have a duplex mismatch:
Fas 9/45
The following interafaces have a native vlan mismatch:
interface (native vlan - neighbor vlan)
Fas 9/45 (1 - 64)
The value for Community-Access on read-only operations for SNMP is the same
as default. Please verify that this is the best value from a security point
of view.

Cisco IOS Configuration Fundamentals Command Reference

CF-664

April 2010

show diagnostic sanity

The value for Community-Access on write-only operations for SNMP is the same
as default. Please verify that this is the best value from a security point
of view.
The value for Community-Access on read-write operations for SNMP is the same
as default. Please verify that this is the best value from a security point
of view.
Please check the status of the following modules:
8,9
Module 2 had a MINOR_ERROR.
The Module 2 failed the following tests:
TestIngressSpan
The following ports from Module2 failed test1:
1,2,4,48

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-665

show disk

show disk
To display flash or file system information for a disk, use the show disk command in user or privileged
EXEC mode.
show {disk0 | disk1} [all | filesys]

Syntax Description

disk0

Selects disk 0 as the disk to display information about.

disk1

Selects disk 1 as the disk to display information about.

all

(Optional) Specifies that all flash information will be displayed for the
selected disk.

filesys

(Optional) Specifies that file system information will be displayed for the
selected disk.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2

This command was introduced in a release prior to Cisco IOS Release 12.2.

12.3(7)T

This command was enhanced to display information about the ATA ROM
monitor library (monlib) file.

12.2(25)S

This command was integrated into the Cisco IOS Release 12.2(25)S.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

Note

Examples

The show disk command is supported only on platforms that have a disk file system.

The name of the ATA monlib file may contain a platform name that does not match the platform that you
are using. Different platforms may have a similar or the same name for their ATA monlib file.

The following example displays information about disk 0. The output is self-explanatory.
Router# show disk0 all
-#- --length-- -----date/time------ path
1
19539160 Jan 27 2004 23:08:40 c7200-is-mz.123-5.7.PI3a
1011679232 bytes available (19546112 bytes used)
******** ATA Flash Card Geometry/Format Info ********
ATA CARD GEOMETRY
Number of Heads:
Number of Cylinders
Sectors per Track

16
1999
63

Cisco IOS Configuration Fundamentals Command Reference

CF-666

April 2010

show disk

Sector Size
Total Sectors
ATA CARD FORMAT
Number of FAT Sectors
Sectors Per Cluster
Number of Clusters
Number of Data Sectors
Base Root Sector
Base FAT Sector
Base Data Sector

512
2014992
246
32
62941
2014789
632
140
664

ATA MONLIB INFO

Image Monlib size = 67256
Disk monlib size = 71680
Name = c7200-atafslib-m
Monlib Start sector = 2
Monlib End sector = 133
Monlib updated by = C7200-IS-M12.3(5.7)PI3a
Monlib version = 1

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-667

show disk0:

show disk0:
To display flash or file system information for a disk located in slot 0, use the show disk command in
user EXEC or privileged EXEC mode.
show disk0: [all | filesys]

Syntax Description

all

(Optional) The all keyword displays complete information about flash

memory, including information about the individual devices in flash memory
and the names and sizes of all system image files stored in flash memory,
including those that are invalid.

filesys

(Optional) Displays the device information block, the status information,

and the usage information.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

11.3AA

This command was introduced.

12.2

This command was incorporated into Cisco IOS Release 12.2.

12.3(7)T

This command was enhanced to display information about the ATA ROM
monitor library (monlib) file.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The show disk0: command is supported only on platforms that have a disk file system located in slot 0.
Use the show disk0: command to display details about the files in a particular ATA PCMCIA flash disk
memory card.
For more information regarding file systems and flash cards, access the PCMCIA Filesystem
Compatibility Matrix and Filesystem Information document at the following URL:
http://www.cisco.com/en/US/partner/products/hw/routers/ps341/products_tech_note09186a00800a751
5.shtml

Note

Examples

The name of the ATA monlib file may contain a platform name that does not match the platform that you
are using. Different platforms may have a similar name or the same name for their ATA monlib file.

The following examples show displays of information about the flash disks or file system information
for a disk. The output is self-explanatory.
c7200# show disk0:
-#- --length-- -----date/time------ path

Cisco IOS Configuration Fundamentals Command Reference

CF-668

April 2010

show disk0:

1
2

29505176 Feb 27 2006 17:56:52 +00:00 c7200-jk9o3s-mz.124-6.T

32768 Feb 24 2006 13:30:30 +00:00 file1.log

34738176 bytes available (29540352 bytes used)

c7200# show disk0: all
-#- --length-- -----date/time------ path
1
29505176 Feb 27 2006 17:56:52 +00:00 c7200-jk9o3s-mz.124-6.T
2
32768 Feb 24 2006 13:30:30 +00:00 file1.log
34738176 bytes available (29540352 bytes used)
******** ATA Flash Card Geometry/Format Info ********
ATA CARD GEOMETRY
Number of Heads:
Number of Cylinders
Sectors per Cylinder
Sector Size
Total Sectors

4
984
32
512
125952

ATA CARD FORMAT

Number of FAT Sectors
Sectors Per Cluster
Number of Clusters
Number of Data Sectors
Base Root Sector
Base FAT Sector
Base Data Sector

62
8
15693
125812
232
108
264

ATA MONLIB INFO

Image Monlib size = 73048
Disk monlib size = 55296
Name = NA
Monlib end sector = NA
Monlib Start sector = NA
Monlib updated by = NA
Monlib version = NA
c7200# show disk0: filesys
******** ATA Flash Card Geometry/Format Info ********
ATA CARD GEOMETRY
Number of Heads:
Number of Cylinders
Sectors per Cylinder
Sector Size
Total Sectors

4
984
32
512
125952

ATA CARD FORMAT

Number of FAT Sectors
Sectors Per Cluster
Number of Clusters
Number of Data Sectors
Base Root Sector
Base FAT Sector
Base Data Sector

62
8
15693
125812
232
108
264

ATA MONLIB INFO

Image Monlib size = 73048
Disk monlib size = 55296
Name = NA

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-669

show disk0:

Monlib
Monlib
Monlib
Monlib

Related Commands

end sector = NA
Start sector = NA
updated by = NA
version = NA

Command

Description

dir disk0:

Displays a directory listing of files on an ATA PCMCIA flash disk card

located in slot 0.

dir disk1:

Displays a directory listing of files on an ATA PCMCIA flash disk card

located in slot 1.

show disk1:

Displays flash or file system information for a disk located in slot 1.

Cisco IOS Configuration Fundamentals Command Reference

CF-670

April 2010

show disk1:

show disk1:
To display flash or file system information for a disk located in slot 1, use the show disk1: command in
user EXEC or privileged EXEC mode.
show disk1: [all | filesys]

Syntax Description

all

(Optional) The all keyword displays complete information about flash

memory, including information about the individual devices in flash memory
and the names and sizes of all system image files stored in flash memory,
including those that are invalid.

filesys

(Optional) Displays the device information block, the status information,

and the usage information.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

11.3AA

This command was introduced.

12.2

This command was incorporated into Cisco IOS Release 12.2.

12.3(7)T

This command was enhanced to display information about the ATA ROM
monitor library (monlib) file.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The show disk1: command is supported only on platforms that have a disk file system. Use the show
disk01: command to display details about the files in a particular ATA PCMCIA flash disk memory card
located in slot 1.
For more information regarding file systems and flash cards, access the PCMCIA Filesystem
Compatibility Matrix and Filesystem Information document at the following URL:
http://www.cisco.com/en/US/partner/products/hw/routers/ps341/products_tech_note09186a00800a751
5.shtml

Note

Examples

The name of the ATA monlib file may contain a platform name that does not match the platform that you
are using. Different platforms may have a similar name or the same name for their ATA monlib file.

The following examples show displays of information about the flash disks or file system information
for a disk. The output is self-explanatory.
c7200# show disk1:
-#- --length-- -----date/time------ path

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-671

show disk1:

1
2

29505176 Feb 27 2006 17:56:52 +00:00 c7200-jk9o3s-mz.124-6.T

32768 Feb 24 2006 13:30:30 +00:00 file1.log

34738176 bytes available (29540352 bytes used)

c7200# show disk1: all
-#- --length-- -----date/time------ path
1
29505176 Feb 27 2006 17:56:52 +00:00 c7200-jk9o3s-mz.124-6.T
2
32768 Feb 24 2006 13:30:30 +00:00 file1.log
34738176 bytes available (29540352 bytes used)
******** ATA Flash Card Geometry/Format Info ********
ATA CARD GEOMETRY
Number of Heads:
Number of Cylinders
Sectors per Cylinder
Sector Size
Total Sectors

4
984
32
512
125952

ATA CARD FORMAT

Number of FAT Sectors
Sectors Per Cluster
Number of Clusters
Number of Data Sectors
Base Root Sector
Base FAT Sector
Base Data Sector

62
8
15693
125812
232
108
264

ATA MONLIB INFO

Image Monlib size = 73048
Disk monlib size = 55296
Name = NA
Monlib end sector = NA
Monlib Start sector = NA
Monlib updated by = NA
Monlib version = NA
c7200# show disk1: filesys
******** ATA Flash Card Geometry/Format Info ********
ATA CARD GEOMETRY
Number of Heads:
Number of Cylinders
Sectors per Cylinder
Sector Size
Total Sectors

4
984
32
512
125952

ATA CARD FORMAT

Number of FAT Sectors
Sectors Per Cluster
Number of Clusters
Number of Data Sectors
Base Root Sector
Base FAT Sector
Base Data Sector

62
8
15693
125812
232
108
264

ATA MONLIB INFO

Image Monlib size = 73048
Disk monlib size = 55296
Name = NA

Cisco IOS Configuration Fundamentals Command Reference

CF-672

April 2010

show disk1:

Monlib
Monlib
Monlib
Monlib

Related Commands

end sector = NA
Start sector = NA
updated by = NA
version = NA

Command

Description

dir disk0:

Displays a directory listing of files on an ATA PCMCIA flash disk card

located in slot 0.

dir disk1:

Displays a directory listing of files on an ATA PCMCIA flash disk card

located in slot 1.

show disk0:

Displays flash or file system information for a disk located in slot 0.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-673

show environment

show environment
To display temperature, voltage, fan, and power supply information, use the show environment
command in user EXEC or privileged EXEC mode.
show environment [alarms | all | fans | hardware | last | leds | power-supply | table | temperature
| voltages]
Cisco 7000 Series, Cisco 7200 Series, Cisco 7304, and Cisco 7500 Series

show environment [all | last | table]

Cisco ASR 1000 Series

show environment {all | counters | history sensor | location sensor | sensor sensor | table sensor}

Syntax Description

alarms

(Optional) Displays the alarm contact information.

all

(Optional) Displays a detailed listing of all environmental monitor parameters

(for example, the power supplies, temperature readings, voltage readings, and
blower speeds). This is the default.

fans

(Optional) Displays blower and fan information.

hardware

(Optional) Displays hardware-specific information.

last

(Optional) Displays information on the last measurement made.

leds

(Optional) Displays the status of the MBus LEDs on the clock and scheduler
cards and switch fabric cards.

power-supply

(Optional) Displays power supply voltage and current information. If

applicable, displays the status of the redundant power supply.

table

(Optional) Displays the temperature, voltage, and blower ranges and

thresholds.
On the Cisco 7200 series, including the NPE-G2 in the Cisco 7200 VXR, the
Cisco 7304 routers, and the Cisco 7500 series routers, the table keyword
displays only the temperature and voltage thresholds.

Command Default

temperature

(Optional) Displays temperature information.

voltages

(Optional) Displays voltage information.

counters

Displays operational counters.

history

Displays sensor state change history.

location

Displays sensors by location.

sensor

Displays sensor summary.

sensor

Sensor name.

If no options are specified, the default is all.

Cisco IOS Configuration Fundamentals Command Reference

CF-674

April 2010

show environment

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History

Usage Guidelines

Release

Modification

10.0

This command was introduced.

11.2 GS

The alarms, fans, hardware, leds, power-supply, table, temperature, and

voltages keywords were added for the Cisco 12000 series GSRs.

11.3(6)AA

This command was expanded to monitor the RPS and board temperature for
the Cisco AS5300 platform, Cisco 3600 series routers, Cisco 7200 series
routers, and the Cisco 12000 series GSRs.

12.2(20)S

This command was integrated into Cisco IOS Release 12.2(20)S.

12.2(20)S2

This command was integrated into Cisco IOS Release 12.2(20)S2 to support
MSCs and SPAs on the Cisco 7304 router using the all, last, and table
keywords.

12.4(4)XD

This command was integrated into Cisco IOS Release 12.4(4)XD to support
the NPE-G2 on the Cisco 7200 VXR using the all, last, and table keywords.
Command output was modified for the NPE-G2.

12.2(31)SB2

This command was integrated into Cisco IOS Release 12.2(31)SB2.

Cisco IOS XE Release

2.1

This command was integrated into Cisco IOS XE Release 2.1 on the Cisco
ASR 1000 Series Routers.

The availability of keywords depends on your system and platform. The command does not support SPAs
on the Cisco 7200 series and on the NPE-G2 in the Cisco 7200 VXR routers.
A routine runs once a minute that reads environmental measurements from sensors and stores the output
into a buffer. For shared port adapters (SPAs), the temperature and voltage sensors are read every few
seconds to get environmental data. The environmental buffer is displayed on the console when you use
the show environment command.
If a measurement exceeds desired margins, but has not exceeded fatal margins, a warning message is
printed to the system console. The system software queries the sensors for measurements once a minute,
but warnings for a given test point are printed at most once every hour for sensor readings in the warning
range and once every 5 minutes for sensor readings in the critical range. If a measurement is out of line
within these time segments, an automatic warning message appears on the console. As noted, you can
query the environmental status with the show environment command at any time to determine whether
a measurement is at the warning or critical tolerance.
A SPA is shut down when any of the SPA environment readings exceed the shutdown threshold.
If a shutdown occurs because of detection of fatal environmental margins, the last measured value from
each sensor is stored in internal nonvolatile memory.
For environmental specifications, refer to the hardware installation and configuration publication for
your individual chassis.
For network processor engines (NPEs), network services engines (NSEs), line cards, and modular
services cards (MSCs), environmental information is recorded in the CISCO-ENVMON-MIB. SPAs are
not supported by the CISCO-ENVMON-MIB. In Cisco IOS Release 12.2(20)S2 and later, the
CISCO-ENTITY-SENSOR-MIB supports environmental information for SPAs, as well as NPEs, NSEs,
line cards, and MSCs.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-675

show environment

If the Cisco 12000 series GSR exceeds environmental conditions, a message similar to the following is
displayed on the console:
%GSR_ENV-2-WARNING: Slot 3 Hot Sensor Temperature exceeds 40 deg C;
Check cooling systems

Note

Blower temperatures that exceed environmental conditions do not generate a warning message.
You can also enable Simple Network Management Protocol (SNMP) notifications (traps or informs) to
alert a network management system (NMS) when environmental thresholds are reached using the
snmp-server enable traps envmon and snmp-server host global configuration commands.
Whenever Cisco IOS software detects a failure or recovery event from the DRPS unit, it sends an SNMP
trap to the configured SNMP server. Unlike console messages, only one SNMP trap is sent when the
failure event is first detected. Another trap is sent when the recovery is detected.
Cisco AS5300 DRPS software reuses the MIB attributes and traps defined in CISCO-ENVMON-MIB
and CISCO-ACCESS-ENVMON-MIB. CISCO-ENVMON-MIB is supported by all Cisco routers with
RPS units, and CISCO-ACCESS-ENVMON-MIB is supported by the Cisco 3600 series routers.
A power supply trap defined in CISCO-ENVMON-MIB is sent when a failure is detected and when a
failure recovery occurs for the following events: input voltage fail, DC output voltage fail, thermal fail,
and multiple failure events.
A fan failure trap defined in CISCO-ENVMON-MIB is sent when a fan failure or recovery event is
detected by Cisco IOS software.
A temperature trap defined in CISCO-ACCESS-ENVMON-MIB is sent when a board over-temperature
condition is detected by Cisco IOS software.
CISCO-ACCESS-ENVMON-MIB also defines an over-voltage trap. A similar trap is defined in
CISCO-ENVMON-MIB, but it requires the ciscoEnvMonVoltageStatusValue in varbinds. This value
indicates the current value of the voltage in the RPS. With Cisco AS5300 RPS units, the current voltage
value is not sent to the motherboard.
CISCO-ENVMON-MIB is extended to add a new enumerated value, internalRedundant(5), for MIB
attribute ciscoEnvMonSupplySource. This is used to identify a RPS unit.

Examples

Cisco ASR 1000 Series Routers

In the following example, the show environment all command displays system temperature, voltage,
fan, and power supply conditions. (It does not display environmental information for SPAs.) The State
column in show environment all output should show Normal except for fans where it indicates fan
speed. A fan speed of 65% is normal.
Router# show environment all
Sensor List: Environmental Monitoring
Sensor
Location
State
V1: VMA
F0
Normal
V1: VMB
F0
Normal
V1: VMC
F0
Normal
V1: VMD
F0
Normal
V1: VME
F0
Normal
V1: 12v
F0
Normal
V1: VDD
F0
Normal
V1: GP1
F0
Normal
V2: VMA
F0
Normal
V2: VMB
F0
Normal
V2: VMC
F0
Normal
V2: VMD
F0
Normal

Reading
1801 mV
1206 mV
1206 mV
1103 mV
1005 mV
11967 mV
3295 mV
905 mV
3295 mV
2495 mV
1499 mV
1098 mV

Cisco IOS Configuration Fundamentals Command Reference

CF-676

April 2010

show environment

V2: VME
V2: VMF
V2: 12v
V2: VDD
V2: GP1
Temp: Inlet
Temp: Asic1
Temp: Exhaust1
Temp: Exhaust2
Temp: Asic2
V1: VMA
V1: VMB
V1: VMC
V1: VMD
V1: VME
V1: VMF
V1: 12v
V1: VDD
V1: GP1
V1: GP2
V2: VMB
V2: 12v
V2: VDD
V2: GP2
Temp: Left
Temp: Center
Temp: Asic1
Temp: Right
V1: VMA
V1: VMB
V1: VMC
V1: VMD
V1: VME
V1: VMF
V1: 12v
V1: VDD
V1: GP1
V1: GP2
V2: VMB
V2: 12v
V2: VDD
V2: GP2
Temp: Left
Temp: Center
Temp: Asic1
Temp: Right
PEM Iout
PEM Vout
PEM Vin
Temp: PEM
Temp: FC
Temp: FM
Temp: FC
V1: VMA
V1: VMB
V1: VMC
V1: VMD
V1: VME
V1: VMF
V1: 12v
V1: VDD
V1: GP1
V1: GP2
Temp: CPU

F0
F0
F0
F0
F0
F0
F0
F0
F0
F0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
P0
P0
P0
P0
P0
P1
P1
R0
R0
R0
R0
R0
R0
R0
R0
R0
R0
R0

Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Fan Speed 65%
Normal
Fan Speed 65%
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal
Normal

1000 mV
1000 mV
11923 mV
3295 mV
751 mV
27 Celsius
44 Celsius
36 Celsius
34 Celsius
40 Celsius
1103 mV
1201 mV
1503 mV
1801 mV
2495 mV
3295 mV
11967 mV
3295 mV
751 mV
903 mV
1201 mV
11967 mV
3291 mV
903 mV
28 Celsius
29 Celsius
42 Celsius
27 Celsius
1103 mV
1201 mV
1503 mV
1801 mV
2495 mV
3295 mV
11953 mV
3291 mV
754 mV
903 mV
1206 mV
11967 mV
3291 mV
905 mV
28 Celsius
30 Celsius
44 Celsius
28 Celsius
37 A
12 V AC
116 V AC
28 Celsius
25 Celsius
1 Celsius
25 Celsius
1118 mV
3315 mV
2519 mV
1811 mV
1513 mV
1220 mV
12011 mV
3300 mV
913 mV
1247 mV
29 Celsius

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-677

show environment

Temp: Outlet
Temp: Inlet
Temp: Asic1

R0
R0
R0

Normal
Normal
Normal

30 Celsius
25 Celsius
30 Celsius

Table 70 describes the significant fields shown in the display.

Table 70

show environment all Field Descriptions

Field

Description

Sensor

Sensor name.

Location

Chassis slot.

State

State description. One of the following values:

Reading

CriticalCritical alarm indicating a service-affecting

condition.

Fan SpeedFan speed (65% is normal).

MajorMajor alarm indicating immediate action is

needed.

MinorMinor alarm indicating warning conditions.

NormalSensor reading is in acceptable range.

ShutdownIf automatic shutdown is enabled, indicates

that the router will shut down.

Voltage or temperature detected by the sensor.

Cisco 7000 Series Routers, Cisco 7200 Series Routers

In the following example, the typical show environment display is shown when no warning conditions
are in the system for the Cisco 7000 series and Cisco 7200 series routers. This information may vary
slightly depending on the platform you are using. The date and time of the query are displayed, along
with the data refresh information and a message indicating that there are no warning conditions.
Router> show environment
Environmental Statistics
Environmental status as of 13:17:39 UTC Thu Jun 6 1996
Data is 7 second(s) old, refresh in 53 second(s)
All Environmental Measurements are within specifications

Table 71 describes the significant fields shown in the display.

Table 71

show environment Field Descriptions

Field

Description

Environmental status as of...

Current date and time.

Data is..., refresh in...

Environmental measurements are output into a buffer every

60 seconds, unless other higher-priority processes are running.

Status message

If environmental measurements are not within specification,

warning messages are displayed.

Cisco IOS Configuration Fundamentals Command Reference

CF-678

April 2010

show environment

NPE-G2 in Cisco 7200 VXR Routers

In the following example, additional temperature and voltage readings for the NPE-G2 in the Cisco 7200
VXR router are displayed by the show environment all command. Power supplies 1 and 2 are on, and
all monitored variables are within the normal operating range.
Router_npe-g2# show environment all
Power Supplies:
Power Supply 1 is Zytek AC Power Supply.
Power Supply 2 is Zytek AC Power Supply.
Temperature readings:
NPE Inlet measured at 25C/77F
NPE Outlet measured at 28C/82F
CPU Die measured at 56C/132F
Voltage readings:
+3.30 V measured at +3.32 V
+1.50 V measured at +1.48 V
+2.50 V measured at +2.46 V
+1.80 V measured at +1.75 V
+1.20 V measured at +1.17 V
VDD_CPU measured at +1.28 V
VDD_MEM measured at +2.50 V
VTT measured at +1.25 V
+3.45 V measured at +3.39 V
-11.95 measured at -11.93 V
+5.15 V measured at +4.96 V
+12.15 V measured at +12.18 V
Envm stats saved 0 time(s) since reload

Table 72

Unit is on.
Unit is on.

=======> additional temperature reading on NPE-G2

=======>
=======>
=======>
=======>
=======>
=======>
=======>
=======>

additional
additional
additional
additional
additional
additional
additional
additional

voltage
voltage
voltage
voltage
voltage
voltage
voltage
voltage

reading
reading
reading
reading
reading
reading
reading
reading

on
on
on
on
on
on
on
on

NPE-G2
NPE-G2
NPE-G2
NPE-G2
NPE-G2
NPE-G2
NPE-G2
NPE-G2

show environment all Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

Power Supply x is present.

Specifies whether the indicated (x) power supply slot is

populated. If a power supply slot is populated, the manufacturer
name and whether it is an AC or DC power supply is displayed.

Unit is ...

Indicates whether the power supply status is on or off.

Temperature readings

Indicates the temperature of air coming in and going out of the

NPE Inlet, NPE Outlet, and CPU Die areas.

NPE Inlet measured at 25C/77F

Indicates that the temperature measurements at the inlet area of

the chassis is 25C/77F, which is within normal operating range.
System shutdown for NPE Inlet is 80C/176F.

NPE Outlet measured at 28C/82F

Indicates that the temperature measurements at the outlet area of

the chassis is 28C/82F, which is within normal operating range.
System shutdown for NPE Outlet is 84C/183F.

CPU Die measured at 56C/132F

Indicates that the temperature measurement at the CPU Die

(internal silicon of the CPU) area of the chassis is 56C/132F,
which is within normal operating range. System shutdown for
CPU Die is 100C/212F.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-679

show environment

Table 72

show environment all Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

Voltage readings:

System voltage measurements that indicate the actual measured

value for the specified power rail, which is named after the
expected target value.

+3.30 V measured at +3.32 V

+1.50 V measured at +1.48 V

For example, the +3.30 V rail, with an expected value of +3.30

V, actually measures at +3.32 V. This is within the target range.
For example, the +1.50 V rail, with an expected value of +1.50
V, actually measures at +1.48 V. This is within the target range.

VDD_CPU measured at +1.28 V

Indicates +1.28 V is the measured voltage of the VDD_CPU

power rail, which is within normal operating range. The expected
value is 1.3 V.

VDD_MEM measured at +2.50 V

Indicates +2.50 V is the measured voltage of the VDD_MEM

power rail, which is within normal operating range. The expected
value is 2.5 V.

VTT measured at +1.25 V

Indicates +1.25 V is the measured voltage of the VTT power rail,

which is within normal operating range. The expected value is
1.25 V.

In the following example, the show environment last command displays the previously saved
measurements (readings) from the last environmental reading before the router was shut down. The
command also displays the reason why the router was shut down, which was power supply shutdown
in this case.
Router_npe-g2# show environment last
NPE Inlet previously measured at 26C/78F
NPE Outlet previously measured at 28C/82F
CPU Die previously measured at 56C/132F
+3.30 V previously measured at +3.32
+1.50 V previously measured at +1.48
+2.50 V previously measured at +2.46
+1.80 V previously measured at +1.75
+1.20 V previously measured at +1.17
VDD_CPU previously measured at +1.28
VDD_MEM previously measured at +2.50
VTT previously measured at +1.25
+3.45 V previously measured at +3.39
-11.95 previously measured at -11.93
+5.15 V previously measured at +4.96
+12.15 V previously measured at +12.18
last shutdown reason - power supply shutdown

Table 73

show environment last Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

NPE Inlet previously measured at

26C/78F

The last measured temperature of the inlet air of the router prior
to shutdown.

NPE Outlet previously measured at The last measured temperature of the outlet air of the router prior
28C/82F
to shutdown.
CPU Die previously measured at
56C/132F

The last measured temperature of the CPU Die prior to

shutdown.

Cisco IOS Configuration Fundamentals Command Reference

CF-680

April 2010

show environment

Table 73

show environment last Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

+3.30 V previously measured at

+3.32

The last measured voltage of the 3.30 V power rail prior to

shutdown.

VDD_CPU previously measured at The last measured voltage of the VDD_CPU power rail prior to
+1.28
shutdown.
VDD_MEM previously measured
at +2.50

The last measured voltage of the VDD_MEM power rail prior to

shutdown.

VTT previously measured at +1.25 The last measured voltage of the VTT power rail prior to
shutdown.
last shutdown reason

Indicates the reason for the shutdown.

In the following example, the show environment table command displays threshold levels in a table
format of the environmental monitor parameters. It displays the high warning, high critical, and high
shutdown temperature thresholds of the NPE inlet, NPE outlet, and CPU Die. It also displays the low
and high critical voltage thresholds, and low and high shut down voltage thresholds for the power rails
on the NPE-G2 in the Cisco 7200 VXR.

Note

The low range temperatures, such as the LowShut, LowCrit, and LowWarn temperature
thresholds, are not checked and are not displayed on the NPE-G2. Also the warning voltage
thresholds, such as LowWarn and HighWarn, are not checked and are not displayed on the
NPE-G2.

Router_npe-g2# show environment table

Sample Point LowShut LowCrit LowWarn HighWarn
NPE Inlet
44C/111F
NPE Outlet
49C/120F
CPU Die
75C/167F
System shutdown for NPE Inlet is 80C/176F
System shutdown for NPE Outlet is 84C/183F
System shutdown for CPU Die is 100C/212F
+3.30 V
+2.30
+3.12
+1.50 V
+1.05
+1.40
+2.50 V
+1.71
+2.34
+1.80 V
+1.25
+1.67
+1.20 V
+0.82
+1.13
VDD_CPU
+0.89
+1.21
VDD_MEM
+1.71
+2.34
VTT
+0.85
+1.17
+3.45 V
+2.38
+3.28
-11.95 V
-8.44
-11.56
+5.15 V
+3.59
+4.88
+12.15 V
+8.55
+11.48

HighCrit HighShut
59C/138F
64C/147F
85C/185F

+3.47
+1.56
+2.61
+1.91
+1.28
+1.36
+2.61
+1.32
+3.63
-12.84
+5.42
+12.77

+4.29
+1.95
+3.28
+2.34
+1.56
+1.71
+3.28
+1.64
+4.49
-15.78
+6.71
+15.82

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-681

show environment

Table 74

show environment table Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

Sample Point

This is the area for which temperature or system voltage

thresholds are displayed.

LowShut

This is the LowShut voltage threshold. If the voltage value is

below the LowShut threshold, the router shuts down.
Note

LowCrit

The LowShut temperature value is not checked and its

threshold is not displayed on the NPE-G2.

This is the low critical voltage threshold. If the voltage value is

below the LowCrit threshold, a critical message is issued for an
out-of-tolerance voltage value. The system continues to operate.
However, the system is approaching shutdown.
Note

The LowCrit temperature value is not checked and its

threshold is not displayed on the NPE-G2.

LowWarn

The LowWarn temperature threshold and LowWarn voltage

threshold are not checked and the threshold information is not
displayed on the NPE-G2.

HighWarn

This is the HighWarn temperature threshold. If the temperature

reaches the HighWarn threshold, a warning message is issued for
an out-of-tolerance temperature value. The system continues to
operate, but operator action is recommended to bring the system
back to a normal state.
Note

HighCrit

This is the HighCrit temperature or voltage threshold. If the

temperature or voltage reaches the HighCrit level, a critical
message is issued. The system continues to operate. However,
the system is approaching shutdown.
Note

HighShut

The HighWarn voltage threshold is not checked and its

threshold is not displayed on the NPE-G2.

Beware that if the temperature reaches or exceeds the

HighShut value, a Shutdown message is issued and the
router shuts down.

This is the HighShut temperature or voltage threshold. If the

temperature or voltage level reaches or exceeds the HighShut
value, a Shutdown message is issued and the router shuts down.

Cisco IOS Configuration Fundamentals Command Reference

CF-682

April 2010

show environment

Table 74

show environment table Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

NPE Inlet 44C/111F 59C/138F

These are the HighWarn and HighCrit temperature thresholds,

respectively, for the NPE Inlet.
If the NPE Inlet temperature value reaches the HighWarn
(44C/111F) and HighCrit (59C/138F) levels, warning and
critical messages, respectively, are issued.
If the value reaches 44C/111F or greater, you receive a warning
message indicating HighWarn. The system continues to operate,
but operator action is recommended to bring the system back to
a normal state.
If the value reaches 59C/138F or greater, you receive a critical
(HighCrit) message instead, that indicates the system continues
to operate, but the system is approaching shutdown.
Note

NPE Outlet 49C/120F 64C/147F

Beware if the temperature reaches or exceeds 80C/176F,

which is the HighShut value, a Shutdown message is
issued, and the NPE Inlet area shuts down.

These are the HighWarn and HighCrit temperature thresholds,

respectively, for the NPE Outlet.
If the NPE Outlet temperature value reaches the HighWarn
(49C/120F) and HighCrit (64C/147F) levels, warning and
critical messages, respectively, are issued.
If the value reaches 49C/120F or greater, you receive a warning
message indicating HighWarn. The system continues to operate,
but operator action is recommended to bring the system back to
a normal state.
If the value reaches 64C/147F or greater, you receive a critical
(HighCrit) message instead that indicates the system continues to
operate, but the system is approaching shutdown.
Note

Beware if the temperature reaches or exceeds 84C/183F,

which is the HighShut value, a Shutdown message is
issued, and the NPE Outlet area shuts down.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-683

show environment

Table 74

show environment table Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

CPU Die 75C/167F 85C/185F

These are the HighWarn and HighCrit temperature thresholds,

respectively, for the CPU Die.
If the CPU Die temperature value reaches the HighWarn
(75C/167F) and HighCrit (85C/185F) levels, warning and
critical messages, respectively, are issued.
If the value reaches 75C/167F or greater, you receive a warning
message indicating HighWarn. The system continues to operate,
but operator action is recommended to bring the system back to
a normal state.
If the value reaches 85C/185F or greater, you receive a critical
(HighCrit) message instead, that indicates the system continues
to operate, but the system is approaching shutdown.
Note

System shutdown for NPE Inlet is

80C/176F

Beware if the temperature reaches or exceeds

100C/212F, which is the HighShut value, a Shutdown
message is issued and the CPU Die area shuts down.

This is the HighShut temperature threshold for the NPE Inlet.

If the temperature reaches or exceeds 80C/176F, a Shutdown
message is issued and the NPE Inlet area is shut down.

System shutdown for NPE Outlet is This is the HighShut temperature threshold for the NPE Outlet.
84C/183F
If the temperature reaches or exceeds 84C/183F, a Shutdown
message is issued and the NPE Outlet area is shut down.
System shutdown for CPU Die is
100C/212F

This is the HighShut temperature threshold for the CPU Die.

+3.30 V +2.30 +3.12 +3.47

+4.29

The voltage thresholds for the +3.30 V power rail are as follows:

If the temperature reaches or exceeds 100C/212F, a Shutdown

message is issued and the CPU Die area is shut down.

+2.30 is the LowShut voltage threshold.

+3.12 is the LowCrit voltage threshold.

+3.47 is the HighCrit voltage threshold.

+4.29 is the HighShut voltage threshold.

Note

The LowWarn and HighWarn voltage levels are not

checked and their thresholds are not displayed on the
NPE-G2.

Cisco IOS Configuration Fundamentals Command Reference

CF-684

April 2010

show environment

Table 74

show environment table Field Descriptions for NPE-G2 in Cisco 7200 VXR Router

Field

Description

VDD_CPU +0.89 +1.21 +1.36

+1.71

The voltage thresholds for the VDD_CPU power rail are as

follows:

+0.89 is the LowShut voltage threshold.

+1.21 is the LowCrit voltage threshold.

+1.36 is the HighCrit voltage threshold.

+1.71 is the HighShut voltage threshold.

Note

VDD_MEM +1.71 +2.34 +2.61

+3.28

The LowWarn and HighWarn voltage levels are not

checked and their thresholds are not displayed on the
NPE-G2.

The voltage thresholds for the VDD_MEM power rail are as

follows:

+1.71 is the LowShut voltage threshold.

+2.34 is the LowCrit voltage threshold.

+2.61 is the HighCrit voltage threshold.

+3.28 is the HighShut voltage threshold.

Note

The LowWarn and HighWarn voltage levels are not

checked and their thresholds are not displayed on the
NPE-G2.

VTT +0.85 +1.17 +1.32 +1.64 The voltage thresholds for the VTT power rail are as follows:

+0.85 is the LowShut voltage threshold.

+1.17 is the LowCrit voltage threshold.

+1.32 is the HighCrit voltage threshold.

+1.64 is the HighShut voltage threshold.

Note

The LowWarn and HighWarn voltage levels are not

checked and their thresholds are not displayed on the
NPE-G2.

Cisco 7000 Series Routers

The following are examples of messages that display on the system console when a measurement has
exceeded an acceptable margin:
ENVIRONMENTAL WARNING: Air flow appears marginal.
ENVIRONMENTAL WARNING: Internal temperature measured 41.3(C)
ENVIRONMENTAL WARNING: +5 volt testpoint measured 5.310(V)

The system displays the following message if voltage or temperature exceed maximum margins:
SHUTDOWN: air flow problem

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-685

show environment

In the following example, there have been two intermittent power failures since a router was turned on,
and the lower power supply is not functioning. The last intermittent power failure occurred on Monday,
June 10, 1996, at 11:07 p.m.
7000# show environment all
Environmental Statistics
Environmental status as of 23:19:47 UTC Wed Jun 12 1996
Data is 6 second(s) old, refresh in 54 second(s)
WARNING: Lower Power Supply is NON-OPERATIONAL
Lower Power Supply:700W, OFF

Upper Power Supply: 700W, ON

Intermittent Powerfail(s): 2

Last on 23:07:05 UTC Mon Jun 10 1996

+12
+5
-12
+24

volts
volts
volts
volts

measured
measured
measured
measured

at 12.05(V)
at
4.96(V)
at -12.05(V)
at 23.80(V)

Airflow temperature measured at 38(C)

Inlet temperature measured at 25(C)

Table 75 describes the significant fields shown in the display.

Table 75

show environment all Field Descriptions for the Cisco 7000 Series Routers

Field

Description

Environmental status as of...

Date and time of last query.

Data is..., refresh in...

Environmental measurements are output into a buffer every 60

seconds, unless other higher-priority processes are running.

WARNING:

If environmental measurements are not within specification,

warning messages are displayed.

Lower Power Supply

Type of power supply installed and its status (on or off).

Upper Power Supply

Type of power supply installed and its status (on or off).

Intermittent Powerfail(s)

Number of power hits (not resulting in shutdown) since the

system was last booted.

Voltage specifications

System voltage measurements.

Airflow and inlet temperature

Temperature of air coming in and going out.

The following example is for the Cisco 7000 series routers. The router retrieves the environmental
statistics at the time of the last shutdown. In this example, the last shutdown was Friday, May 19, 1995,
at 12:40 p.m., so the environmental statistics at that time are displayed.
Router# show environment last
Environmental Statistics
Environmental status as of 14:47:00 UTC Sun May 21 1995
Data is 6 second(s) old, refresh in 54 second(s)
WARNING: Upper Power Supply is NON-OPERATIONAL
LAST Environmental Statistics
Environmental status as of 12:40:00 UTC Fri May 19 1995

Cisco IOS Configuration Fundamentals Command Reference

CF-686

April 2010

show environment

Lower Power Supply: 700W, ON

Upper Power Supply: 700W, OFF

No Intermittent Powerfails
+12
+5
-12
+24

volts
volts
volts
volts

measured
measured
measured
measured

at 12.05(V)
at
4.98(V)
at -12.00(V)
at 23.80(V)

Airflow temperature measured at 30(C)

Inlet temperature measured at 23(C)

Table 76 describes the significant fields shown in the display.

Table 76

show environment last Field Descriptions for the Cisco 7000 Series Routers

Field

Description

Environmental status as of...

Date and time of last query.

Data is..., refresh in...

Environmental measurements are output into a buffer every

60 seconds, unless other higher-priority processes are running.

WARNING:

If environmental measurements are not within specification,

warning messages are displayed.

LAST Environmental Statistics

Displays test point values at time of the last environmental

shutdown.

Lower Power Supply

For the Cisco 7000 router, indicates the status of the

two 700W power supplies.

Upper Power Supply

For the Cisco 7010 router, indicates the status of the

single 600W power supply.
The following example shows sample output for the current environmental status in tables that list
voltage and temperature parameters. There are three warning messages: one each about the lower power
supply, the airflow temperature, and the inlet temperature. In this example, voltage parameters are shown
to be in the normal range, airflow temperature is at a critical level, and inlet temperature is at the warning
level.
Router> show environment table
Environmental Statistics
Environmental status as of Mon 11-2-1992 17:43:36
Data is 52 second(s) old, refresh in 8 second(s)
WARNING: Lower Power Supply is NON-OPERATIONAL
WARNING: Airflow temperature has reached CRITICAL level at 73(C)
WARNING: Inlet temperature has reached WARNING level at 41(C)
Voltage Parameters:
SENSE
CRITICAL
NORMAL
CRITICAL
-------|--------------------|------------------------|-------------------+12(V)
+5(V)
-12(V)
+24(V)

10.20
4.74
-10.20
20.00

12.05(V)
4.98(V)
-12.05(V)
24.00(V)

13.80
5.26
-13.80
28.00

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-687

show environment

Temperature Parameters:
SENSE
WARNING
NORMAL
WARNING
CRITICAL
SHUTDOWN
-------|-------------|------------|-------------|--------------|----------Airflow
Inlet

10
10

60
39

70
41(C)

73(C)
46

88
64

Table 77 describes the significant fields shown in the display.

Table 77

show environment table Field Descriptions for the Cisco 7000 Series Routers

Field

Description

SENSE (Voltage Parameters)

Voltage specification for a DC line.

SENSE (Temperature
Parameters)

Air being measured. Inlet measures the air coming in, and Airflow
measures the temperature of the air inside the chassis.

WARNING

System is approaching an out-of-tolerance condition.

NORMAL

All monitored conditions meet normal requirements.

CRITICAL

Out-of-tolerance condition exists.

SHUTDOWN

Processor has detected condition that could cause physical damage to

the system.

Cisco 7200 Series Routers

The system displays the following message if the voltage or temperature enters the Warning range:
%ENVM-4-ENVWARN: Chassis outlet 3 measured at 55C/131F

The system displays the following message if the voltage or temperature enters the Critical range:
%ENVM-2-ENVCRIT: +3.45 V measured at +3.65 V

The system displays the following message if the voltage or temperature exceeds the maximum margins:
%ENVM-0-SHUTDOWN: Environmental Monitor initiated shutdown

The following message is sent to the console if a power supply has been inserted or removed from the
system. This message relates only to systems that have two power supplies.
%ENVM-6-PSCHANGE: Power Supply 1 changed from Zytek AC Power Supply to removed

The following message is sent to the console if a power supply has been powered on or off. In the case
of the power supply being shut off, this message can be due to the user shutting off the power supply or
to a failed power supply. This message relates only to systems that have two power supplies.
%ENVM-6-PSLEV: Power Supply 1 state changed from normal to shutdown

The following is sample output from the show environment all command on the Cisco 7200 series
routers when there is a voltage warning condition in the system:
7200# show environment all
Power Supplies:
Power supply 1 is unknown. Unit is off.
Power supply 2 is Zytek AC Power Supply. Unit is on.
Temperature readings:
chassis inlet
measured at 25C/77F
chassis outlet 1 measured at 29C/84F

Cisco IOS Configuration Fundamentals Command Reference

CF-688

April 2010

show environment

chassis outlet 2
chassis outlet 3
Voltage readings:
+3.45 V measured
+5.15 V measured
+12.15 measured
-11.95 measured

measured at 36C/96F
measured at 44C/111F
at
at
at
at

+3.83 V:Voltage in Warning range!

+5.09 V
+12.42 V
-12.10 V

Table 78 describes the significant fields shown in the display.

Table 78

show environment all Field Descriptions for the Cisco 7200 Series Router

Field

Description

Power Supplies

Current condition of the power supplies including the type and

whether the power supply is on or off.

Temperature readings

Current measurements of the chassis temperature at the inlet and

outlet locations.

Voltage readings

Current measurement of the power supply test points.

The following example is for the Cisco 7200 series routers. This example shows the measurements
immediately before the last shutdown and the reason for the last shutdown (if appropriate).
7200# show environment last
chassis
chassis
chassis
chassis
+3.3 V
+5.0 V
+12.0 V
-12.0 V

inlet
outlet 1
outlet 2
outlet 3

previously
previously
previously
previously
previously
previously
previously
previously

measured
measured
measured
measured
measured
measured
measured
measured

at
at
at
at
at
at
at
at

27C/80F
31C/87F
37C/98F
45C/113F
4.02
4.92
12.65
11.71

last shutdown reason - power supply shutdown

Table 79 describes the significant fields shown in the display.

Table 79

show environment last Field Descriptions for the Cisco 7200 Series Router

Field

Description

chassis inlet

Temperature measurements at the inlet area of the chassis.

chassis outlet

Temperature measurements at the outlet areas of the chassis.

voltages

Power supply test point measurements.

last shutdown reason

Possible shutdown reasons are power supply shutdown, critical

temperature, and critical voltage.

The following example is for the Cisco 7200 series routers. This information lists the temperature and
voltage shutdown thresholds for each sensor.
7200# show environment table
Sample Point
chassis inlet
chassis outlet 1
chassis outlet 2

LowCritical

LowWarning

HighWarning
40C/104F
43C/109F
75C/167F

HighCritical
50C/122F
53C/127F
75C/167F

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-689

show environment

chassis outlet 3
+3.45 V
+2.76
+5.15 V
+4.10
+12.15 V
+9.72
-11.95 V
-8.37
Shutdown system at 70C/158F

+3.10
+4.61
+10.91
-9.57

55C/131F
+3.80
+5.67
+13.37
-14.34

65C/149F
+4.14
+6.17
+14.60
-15.53

Table 80 describes the significant fields shown in the display.

Table 80

show environment table Field Descriptions for the Cisco 7200 Series Router

Field

Description

Sample Point

Area for which measurements are taken.

LowCritical

Level at which a critical message is issued for an

out-of-tolerance voltage condition. The system continues to
operate; however, the system is approaching shutdown.

LowWarning

Level at which a warning message is issued for an

out-of-tolerance voltage condition. The system continues to
operate, but operator action is recommended to bring the system
back to a normal state.

HighWarning

Level at which a warning message is issued. The system

continues to operate, but operator action is recommended to
bring the system back to a normal state.

HighCritical

Level at which a critical message is issued. For the chassis, the

router is shut down. For the power supply, the power supply is
shut down.

Shutdown system at

The system is shut down if the specified temperature is met.

Cisco 7500 Series Routers

The sample output for the Cisco 7500 series routers may vary depending on the specific model (for
example, the Cisco 7513 router). The following is sample output from the show environment all
command on the Cisco 7500 series routers:
7500# show environment all
Arbiter type 1, backplane type 7513 (id 2)
Power supply #1 is 1200W AC (id 1), power supply #2 is removed (id 7)
Active fault conditions: none
Fan transfer point: 100%
Active trip points: Restart_Inhibit
15 of 15 soft shutdowns remaining before hard shutdown

Dbus slots:
card
RSP(6)
RSP(7)

1
0123456789012
X
XX
X
inlet
35C/95F
35C/95F

hotpoint
47C/116F
43C/109F

exhaust
40C/104F
39C/102F

Shutdown temperature source is hotpoint on RSP(6), requested RSP(6)

+12V measured at 12.31
+5V measured at 5.21
-12V measured at -12.07
+24V measured at 22.08

Cisco IOS Configuration Fundamentals Command Reference

CF-690

April 2010

show environment

+2.5 reference is 2.49

PS1
PS1
PS1
PS1

+5V Current
+12V Current
-12V Current
output is 378 W

measured at 59.61 A (capacity 200 A)

measured at 5.08 A (capacity 35 A)
measured at 0.42 A (capacity 3 A)

Table 81 describes the significant fields shown in the display.

Table 81

show environment all Field Descriptions for the Cisco 7500 Series Routers

Field

Description

Arbiter type 1

Numbers indicating the arbiter type and backplane type.

Power supply

Number and type of power supply installed in the chassis.

Active fault conditions:

Lists any fault conditions that exist (such as power supply

failure, fan failure, and temperature too high).

Fan transfer point:

Software-controlled fan speed. If the router is operating below its

automatic restart temperature, the transfer point is reduced by
10 percent of the full range each minute. If the router is at or
above its automatic restart temperature, the transfer point is
increased in the same way.

Active trip points:

Compares temperature sensor against the values displayed at the

bottom of the show environment table command output.

15 of 15 soft shutdowns remaining When the temperature increases above the board shutdown
level, a soft shutdown occurs (that is, the cards are shut down,
and the power supplies, fans, and CI continue to operate). When
the system cools to the restart level, the system restarts. The
system counts the number of times this occurs and keeps the
up/down cycle from continuing forever. When the counter
reaches zero, the system performs a hard shutdown, which
requires a power cycle to recover. The soft shutdown counter is
reset to its maximum value after the system has been up for
6 hours.
Dbus slots:

Indicates which chassis slots are occupied.

card, inlet, hotpoint, exhaust

Temperature measurements at the inlet, hotpoint, and exhaust

areas of the card. The (6) and (7) indicate the slot numbers. Dual
Route Switch Processor (RSP) chassis can show two RSPs.

Shutdown temperature source

Indicates which of the three temperature sources is selected for

comparison against the shutdown levels listed with the
show environment table command.

Voltages (+12V, +5V, -12V, +24V,

+2.5)

Voltages measured on the backplane.

PS1

Current measured on the power supply.

The following example is for the Cisco 7500 series routers. This example shows the measurements
immediately before the last shutdown.
7500# show environment last
RSP(4) Inlet
RSP(4) Hotpoint

previously measured at 37C/98F

previously measured at 46C/114F

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-691

show environment

RSP(4) Exhaust
+12 Voltage
+5 Voltage
-12 Voltage
+24 Voltage

previously
previously
previously
previously
previously

measured
measured
measured
measured
measured

at
at
at
at
at

52C/125F
12.26
5.17
-12.03
23.78

Table 82 describes the significant fields shown in the display.

Table 82

show environment last Field Descriptions for the Cisco 7500 Series Routers

Field

Description

RSP(4) Inlet, Hotpoint, Exhaust

Temperature measurements at the inlet, hotpoint, and exhaust

areas of the card.

Voltages

Voltages measured on the backplane.

The following example is for the Cisco 7500 series router. This information lists the temperature and
voltage thresholds for each sensor. These thresholds indicate when error messages occur. There are two
level of messages: warning and critical.
7500# show environment table
Sample Point
LowCritical
LowWarning
RSP(4) Inlet
RSP(4) Hotpoint
RSP(4) Exhaust
+12 Voltage
10.90
11.61
+5 Voltage
4.61
4.94
-12 Voltage
-10.15
-10.76
+24 Voltage
20.38
21.51
2.5 Reference
2.43
Shutdown boards at
70C/158F
Shutdown power supplies at
76C/168F
Restart after shutdown below 40C/104F

HighWarning
44C/111F
54C/129F

HighCritical
50C/122F
60C/140F

12.82
5.46
-13.25
26.42
2.51

13.38
5.70
-13.86
27.65

Table 83 describes the significant fields shown in the display.

Table 83

show environment table Field Descriptions for the Cisco 7500 Series Routers

Field

Description

Sample Point

Area for which measurements are taken.

LowCritical

Level at which a critical message is issued for an

out-of-tolerance voltage condition. The system continues to
operate; however, the system is approaching shutdown.

LowWarning

Level at which a warning message is issued for an

out-of-tolerance voltage condition. The system continues to
operate, but operator action is recommended to bring the system
back to a normal state.

HighWarning

Level at which a warning message is issued. The system

continues to operate, but operator action is recommended to
bring the system back to a normal state.

HighCritical

Level at which a critical message is issued. For the chassis, the

router is shut down. For the power supply, the power supply is
shut down.

Cisco IOS Configuration Fundamentals Command Reference

CF-692

April 2010

show environment

Table 83

show environment table Field Descriptions for the Cisco 7500 (continued)Series

Field

Description

Shutdown boards at

The card is shut down if the specified temperature is met.

Shutdown power supplies at

The system is shut down if the specified temperature is met.

Restart after shutdown

The system will restart when the specified temperature is met.

Cisco AS5300 Series Access Servers

In the following example, keywords and options are limited according to the physical characteristics of
the system is shown:
as5300# show environment ?
all
last
table
|
<cr>

All environmental monitor parameters

Last environmental monitor parameters
Temperature and voltage ranges
Output modifiers

as5300# show environment table

%This option not available on this platform

Cisco 12000 Series GSRs

The following examples are for the Cisco 12000 series GSRs.
The following is sample output from the show environment command for a Cisco 12012 router. Slots
0 through 11 are the line cards, slots 16 and 17 are the clock and scheduler cards, slots 18 through 20 are
the switch fabric cards, slots 24 through 26 are the power supplies, and slots 28 and 29 are the blowers.
An NA in the table means that no values were returned. In some cases it is because the equipment is
not supported for that environmental parameter (for example, the power supply and blowers in slots 24,
26, 28, and 29 do not have a 3V power supply, so an NA is displayed).
Router# show environment
Slot #
0
2
4
7
9
11
16
17
18
19
20
24
26
28
29
Slot #
24
26

3V
(mv)
3300
3296
3280
3280
3292
3288
3308
3292
3304
3300
3304
NA
NA
NA
NA

5V
(mv)
4992
4976
4992
4984
4968
4992
NA
NA
NA
NA
NA
5536
5544
NA
NA

48V
(Volt)
46
46

AMP_48
(Amp)
12
19

MBUS 5V Hot Sensor

(mv)
(deg C)
5040
42.0
5136
40.0
5120
38.5
5136
42.0
5160
39.5
5152
40.0
5056
42.5
5056
40.5
5176
36.5
5184
37.5
5168
36.5
5120
NA
5128
NA
5128
NA
5104
NA

Inlet Sensor
(deg C)
37.0
33.0
31.5
32.0
31.5
30.5
38.0
36.5
35.0
33.5
34.0
31.5
31.5
NA
NA

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-693

show environment

Slot #
28
29

Fan 0
(RPM)
2160
2130

Fan 1
(RPM)
2190
2190

Fan 2
(RPM)
2160
2070

Table 84 describes the significant fields shown and lists the equipment supported by each environmental
parameter. NA indicates that the reading could not be obtained, so the command should be run again.
Table 84

show environment Field Descriptions for the Cisco 12000 Series Routers

Field

Description

Slot #

Slot number of the equipment. On the Cisco 12012 router, slots 0 through 11
are the line cards, slots 16 and 17 are the clock and scheduler cards, slots 18
through 20 are the switch fabric cards, slots 24 through 27 are the power
supplies, and slots 28 and 29 are the blowers.

3V (mv)

Measures the 3V power supply on the card. The 3V power supply is on the line
cards, GRP card, clock and scheduler cards, and switch fabric cards.

5V (mv)

Measures the 5V power supply on the card. The 5V power supply is on the line
cards, GRP card, and power supplies.

MBUS 5V (mv)

Measures the 5V MBus on the card. The 5V MBus is on all equipment.

Hot Sensor (deg C)

Measures the temperature at the hot sensor on the card. The hot sensor is on the
line cards, GRP card, clock and scheduler cards, switch fabric cards, and
blowers.

Inlet Sensor (deg C) Measures the current inlet temperature on the card. The inlet sensor is on the
line cards, GRP card, clock and scheduler cards, switch fabric cards, and power
supplies.
48V (Volt)

Measures the DC power supplies.

AMP_48 (Amp)

Measures the AC power supplies.

Fan 0, Fan 1, Fan 2

(RPM)

Measures the fan speed in rotations per minute.

The following is sample output from the show environment all command for the Cisco 12008 router.
Slots 0 through 7 are the line cards, slots 16 and 17 are the clock scheduler cards (the clock scheduler
cards control the fans), slots 18 through 20 are the switch fabric cards, and slots 24 and 26 are the power
supplies. The Cisco 12008 router does not support slots 25, 27, 28, and 29. An NA in the table means
that no values were returned. In some cases it is because the equipment is not supported for that
environmental parameter (for example, the power supplies in slots 24 and 26 do not have a hot sensor,
so an NA is displayed).
Router# show environment all
Slot #
2
5
16
18
19
24
26

Hot Sensor
(deg C)
31.0
33.5
25.5
22.0
22.5
NA
NA

Inlet Sensor
(deg C)
22.0
26.5
21.5
21.0
21.0
29.5
24.5

Cisco IOS Configuration Fundamentals Command Reference

CF-694

April 2010

show environment

Slot #

3V
(mv)
3292
3292
3272
3300
3316

5V
(mv)
5008
5000
NA
NA
NA

24
26

5V
(mv)
0
5544

MBUS 5V 48V
(mv)
(Volt)
5096
3
5144
47

Slot #
16

Fan Information
Voltage 16V Speed slow: Main Fans Ok Power Supply fans Ok

2
5
16
18
19
Slot #

MBUS 5V
(mv)
5136
5128
5128
5128
5128
AMP_48
(Amp)
0
3

Alarm Indicators
No alarms
Slot #
16
18
19
24
26

Card Specific Leds

Mbus OK SFCs Failed
Mbus OK
Mbus OK
Input Failed
Input Ok

The following is sample output from the show environment table command for a Cisco 12012 router.
The show environment table command lists the warning, critical, and shutdown limits on your system
and includes the GRP card and line cards (slots 0 to 15), clock and scheduler cards (slots 16 and 17),
switch fabric cards (slots 18 to 20), and blowers.
Router# show environment table
Hot Sensor Temperature Limits (deg C):
Warning Critical Shutdown
GRP/GLC (Slots 0-15)
40
46
57
CSC
(Slots 16-17)
46
51
65
SFC
(Slots 18-20)
41
46
60
Inlet Sensor Temperature Limits (deg C):
Warning Critical Shutdown
GRP/GLC (Slots 0-15)
35
40
52
CSC
(Slots 16-17)
40
45
59
SFC
(Slots 18-20)
37
42
54
3V Ranges (mv):

GRP/GLC (Slots 0-15)

CSC
(Slots 16-17)
SFC
(Slots 18-20)

Warning
Below
Above
3200
3400
3200
3400
3200
3400

Critical
Below Above
3100
3500
3100
3500
3100
3500

Shutdown
Below Above
3050
3550
3050
3550
3050
3550

Warning
Below
Above
4850
5150

Critical
Below Above
4750
5250

Shutdown
Below Above
4680
5320

Warning
Below
Above
5000
5250
4820
5150
5000
5250

Critical
Below Above
4900
5350
4720
5250
4900
5350

Shutdown
Below Above
4750
5450
4750
5450
4750
5450

5V Ranges (mv):

GRP/GLC (Slots 0-15)

MBUS_5V Ranges (mv):

GRP/GLC (Slots 0-15)

CSC
(Slots 16-17)
SFC
(Slots 17-20)

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-695

show environment

Blower Operational Range (RPM):

Top Blower:

Fan 0
Fan 1
Fan 2

Warning
Below
1000
1000
1000

Critical
Below
750
750
750

Warning
Below
1000
1000
1000

Critical
Below
750
750
750

Bottom Blower:

Fan 0
Fan 1
Fan 2

The following is sample output from the show environment leds command for a Cisco 12012 router.
The show environment leds command lists the status of the MBus LEDs on the clock, scheduler, and
the switch fabric cards.
Router# show environment leds
16
18
19
20

leds
leds
leds
leds

Mbus
Mbus
Mbus
Mbus

OK
OK
OK
OK

Cisco 7304 Router

The following is sample output from the show environment all command on a Cisco 7304 router with
modular services cards (MSCs) and shared port adapters (SPAs) installed:
Router# show environment all
Power Supplies:
Power supply 1 is AC power supply. Unit is on.
Power supply 2 is empty.
Fans:
Fan 1 is on.
Fan 2 is on.
Temperature readings:
Active RP (NPEG100, slot 0):
npeg100 outlet
measured at 29C/84F
npeg100 inlet
measured at 34C/93F
npeg100 hotspot
measured at 35C/95F
Line card (7304-MSC-100, slot 4):
7304-MSC-100
measured at 32C/89F
Card in subslot 4/0:
SPA-4FE-7304 inlet
measured at 31C/87F
SPA-4FE-7304 outlet measured at 32C/89F
Voltage readings:
Active RP (NPEG100, slot 0):
npe outlet 2.5 V
measured at 2.496 V
npe outlet 3.3 V
measured at 3.302 V
npe outlet 5.0 V
measured at 4.992 V
npe outlet 12.0 V
measured at 11.812 V
npe outlet 3.3c V
measured at 3.199 V
npe inlet
1.5 V
measured at 1.494 V
npe outlet 1.8 V
measured at 1.790 V
npe outlet 1.2 V
measured at 1.198 V
npe outlet 1.2c V
measured at 1.198 V

Cisco IOS Configuration Fundamentals Command Reference

CF-696

April 2010

show environment

Line card (7304-MSC-100, slot 4):

7304-MSC-100 0.75 V measured at 0.733 V
7304-MSC-100 1.5 V
measured at 1.494 V
7304-MSC-100 2.5 V
measured at 2.483 V
7304-MSC-100 3.3 V
measured at 3.250 V
7304-MSC-100 12 V
measured at 11.937 V
Card in subslot 4/0:
SPA-4FE-7304 1.8V
measured at 1.802 V
SPA-4FE-7304 1.5V
measured at 1.503 V
SPA-4FE-7304 2.5V
measured at 2.474 V
SPA-4FE-7304 3.3V
measured at 3.252 V
SPA-4FE-7304 1.0V
measured at 1.015 V
Envm stats saved 13 time(s) since reload

The following is sample output from the show environment last command on a Cisco 7304 router with
MSCs and SPAs installed and an NSE-100:
Router# show environment last
Temperature information:
NSE board:
nse outlet
is unmeasured
nse inlet
is unmeasured
nse hotspot
is unmeasured
nse db
is unmeasured
Line card slot 4:
7304-MSC-100
is unmeasured
Card in subslot 4/1:
SPA-4FE-7304 inlet
previously measured
SPA-4FE-7304 outlet previously measured
Voltage information:
NSE board:
nse outlet 1.8 V
is unmeasured
nse outlet 2.5 V
is unmeasured
nse outlet 3.3 V
is unmeasured
nse outlet 5 V
is unmeasured
nse outlet 12 V
is unmeasured
nse inlet 1.8 V
is unmeasured
nse inlet 3.3 V
is unmeasured
nse inlet 1.5 V
is unmeasured
nse hotspot 1.8 V
is unmeasured
nse db 1.65 V
is unmeasured
nse db 1.8 V
is unmeasured
Line card slot 4:
7304-MSC-100 0.75 V is unmeasured
7304-MSC-100 1.5 V
is unmeasured
7304-MSC-100 2.5 V
is unmeasured
7304-MSC-100 3.3 V
is unmeasured
7304-MSC-100 12 V
is unmeasured
Card in subslot 4/1:
SPA-4FE-7304 1.8V
previously measured
SPA-4FE-7304 1.5V
previously measured
SPA-4FE-7304 2.5V
previously measured
SPA-4FE-7304 3.3V
previously measured
SPA-4FE-7304 1.0V
previously measured
Last shutdown reason: shutdown undefined

at 30C/86F
at 32C/89F

at
at
at
at
at

1.823
1.512
2.504
3.258
1.014

V
V
V
V
V

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-697

show environment

The following is sample output from the show environment table command on a Cisco 7304 router with
MSCs and SPAs installed:
Router# show environment table
Temperature tables:
Active RP (NPEG100, slot 0):
Sample Point
HighWarning
npeg100 outlet
53C/127F
npeg100 inlet
53C/127F
npeg100 hotspot
53C/127F
Line card (7304-MSC-100, slot 4):
Sample Point
HighWarning
7304-MSC-100
48C/118F
Card in subslot 4/0:
Sample Point
HighWarning
SPA-4FE-7304 inlet 52C/125F
SPA-4FE-7304 outlet 52C/125F
Voltage tables:
Active RP (NPEG100, slot 0):
Sample Point
LowShut LowCrit
npe outlet 2.5 V 2.275 V 2.375 V
npe outlet 3.3 V 3.003 V 3.135 V
npe outlet 5.0 V 4.500 V 4.750 V
npe outlet 12.0 V 9.960 V 10.440 V
npe outlet 3.3c V 3.003 V 3.135 V
npe inlet
1.5 V 1.350 V 1.425 V
npe outlet 1.8 V 1.620 V 1.710 V
npe outlet 1.2 V 1.128 V 1.164 V
npe outlet 1.2c V 1.128 V 1.164 V
Line card (7304-MSC-100, slot 4):
Sample Point
LowShut LowCrit
7304-MSC-100 0.75 0.559 V 0.600 V
7304-MSC-100 1.5 V 1.350 V 1.440 V
7304-MSC-100 2.5 V 2.250 V 2.375 V
7304-MSC-100 3.3 V 2.970 V 3.135 V
7304-MSC-100 12 V 9.960 V 10.440 V
Card in subslot 4/0:
Sample Point
LowShut LowCrit
SPA-4FE-7304 1.8V 1.620 V 1.710 V
SPA-4FE-7304 1.5V 1.350 V 1.425 V
SPA-4FE-7304 2.5V 2.250 V 2.375 V
SPA-4FE-7304 3.3V 2.970 V 3.135 V
SPA-4FE-7304 1.0V 0.900 V 0.950 V

HighCritical HighShutdown
68C/154F
73C/163F
68C/154F
73C/163F
68C/154F
73C/163F
HighCritical HighShutdown
63C/145F
68C/154F
HighCritical HighShutdown
67C/152F
72C/161F
67C/152F
72C/161F

LowWarn HighWarn HighCrit HighShut

2.400 V 2.600 V 2.625 V 2.725 V
3.185 V 3.415 V 3.465 V 3.597 V
4.800 V 5.200 V 5.250 V 5.500 V
10.800 V 13.200 V 13.560 V 14.040 V
3.185 V 3.415 V 3.465 V 3.597 V
1.455 V 1.545 V 1.575 V 1.650 V
1.728 V 1.872 V 1.890 V 1.980 V
1.167 V 1.233 V 1.236 V 1.272 V
1.167 V 1.233 V 1.236 V 1.272 V
LowWarn HighWarn HighCrit HighShut
0.600 V 0.900 V 0.900 V 0.941 V
1.455 V 1.545 V 1.560 V 1.650 V
2.400 V 2.600 V 2.625 V 2.750 V
3.168 V 3.432 V 3.465 V 3.630 V
10.800 V 13.200 V 13.560 V 14.040 V
LowWarn
1.728 V
1.440 V
2.400 V
3.168 V
0.960 V

HighWarn
1.872 V
1.560 V
2.600 V
3.432 V
1.040 V

HighCrit
1.890 V
1.575 V
2.625 V
3.465 V
1.050 V

HighShut
1.980 V
1.650 V
2.750 V
3.630 V
1.100 V

Table 85 describes the significant fields shown in the display.

Table 85

show environment table Field Descriptions for the Cisco 7304 Router

Field

Description

Sample Point

Area for which measurements are taken.

LowShut

Lowest level for an out-of-tolerance condition at which the

system shuts itself down. For out-of-tolerance conditions with
SPA environment variables, only the SPA is shut down.

LowCrit/LowCritical

Level at which a critical message is issued for an

out-of-tolerance voltage condition. The system continues to
operate; however, the system is approaching shutdown.

Cisco IOS Configuration Fundamentals Command Reference

CF-698

April 2010

show environment

Table 85

Related Commands

show environment table Field Descriptions for the Cisco 7304 Router (continued)

Field

Description

LowWarn/LowWarning

Level at which a warning message is issued for an

out-of-tolerance voltage condition. The system continues to
operate, but operator action is recommended to bring the
system back to a normal state.

HighWarn/HighWarning

Level at which a warning message is issued for an

out-of-tolerance voltage condition. The system continues to
operate, but operator action is recommended to bring the
system back to a normal state.

HighCrit/HighCritical

Level at which a critical message is issued for an

out-of-tolerance voltage condition. The system continues to
operate; however, the system is approaching shutdown.

HighShut/HighShutdown

Highest level for an out-of-tolerance condition at which the

system shuts itself down. For out-of-tolerance conditions with
SPA environment variables, only the SPA is shut down.

Command

Description

snmp-server enable traps envmon Controls (enables or disables) environmental monitoring

SNMP notifications.
snmp-server host

Specifies how SNMP notifications should be sent (as traps or

informs), the version of SNMP to use, the security level of the
notifications (for SNMPv3), and the recipient (host) of the
notifications.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-699

show environment alarm

show environment alarm

To display the information about the environmental alarm, use the show environment alarm command
in user EXEC or privileged EXEC mode.
show environment alarm [{status | threshold} [frutype]]

Syntax Description

status

(Optional) Displays the operational FRU status.

threshold

(Optional) Displays the preprogrammed alarm thresholds.

frutype

(Optional) Alarm type; valid values are all, backplane, clock number, earl slot,
fan-tray, module slot, rp slot, power-supply number, supervisor slot, and vtt number.
See the Note for a list of valid values for number and slot.

Defaults

If you do not enter a frutype, all the information about the environmental alarm status is displayed.

Command Modes

User EXEC
Privileged EXEC

Command History

Usage Guidelines

Note

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Valid values for the frutype are as follows:

clock number1 and 2.

earl slotSee the Note for valid values.

module slotSee the Note for valid values.

rp slotSee the Note for valid values.

power-supply number1 and 2.

supervisor slotSee the Note for valid values.

vtt number1 to 3.

The slot argument designates the module and port number. Valid values for slot depend on the chassis
and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is
installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the
port number are from 1 to 48.

Cisco IOS Configuration Fundamentals Command Reference

CF-700

April 2010

show environment alarm

Examples

This example shows how to display all the information about the status of the environmental alarm:
Router> show environment alarm threshold
environmental alarm thresholds:
power-supply 1 fan-fail: OK
threshold #1 for power-supply 1 fan-fail:
(sensor value != 0) is system minor alarm
power-supply 1 power-output-fail: OK
threshold #1 for power-supply 1 power-output-fail:
(sensor value != 0) is system minor alarm
fantray fan operation sensor: OK
threshold #1 for fantray fan operation sensor:
(sensor value != 0) is system minor alarm
operating clock count: 2
threshold #1 for operating clock count:
(sensor value < 2) is system minor alarm
threshold #2 for operating clock count:
(sensor value < 1) is system major alarm
operating VTT count: 3
threshold #1 for operating VTT count:
(sensor value < 3) is system minor alarm
threshold #2 for operating VTT count:
(sensor value < 2) is system major alarm
VTT 1 OK: OK
threshold #1 for VTT 1 OK:
(sensor value != 0) is system minor alarm
VTT 2 OK: OK
threshold #1 for VTT 2 OK:
(sensor value != 0) is system minor alarm
VTT 3 OK: OK
threshold #1 for VTT 3 OK:
(sensor value != 0) is system minor alarm
clock 1 OK: OK
threshold #1 for clock 1 OK:
(sensor value != 0) is system minor alarm
clock 2 OK: OK
threshold #1 for clock 2 OK:
(sensor value != 0) is system minor alarm
module 1 power-output-fail: OK
threshold #1 for module 1 power-output-fail:
(sensor value != 0) is system major alarm
module 1 outlet temperature: 21C
threshold #1 for module 1 outlet temperature:
(sensor value > 60) is system minor alarm
threshold #2 for module 1 outlet temperature:
(sensor value > 70) is system major alarm
module 1 inlet temperature: 25C
threshold #1 for module 1 inlet temperature:
(sensor value > 60) is system minor alarm
threshold #2 for module 1 inlet temperature:
(sensor value > 70) is system major alarm
module 1 device-1 temperature: 30C
threshold #1 for module 1 device-1 temperature:
(sensor value > 60) is system minor alarm
threshold #2 for module 1 device-1 temperature:
(sensor value > 70) is system major alarm
module 1 device-2 temperature: 29C
threshold #1 for module 1 device-2 temperature:
(sensor value > 60) is system minor alarm
threshold #2 for module 1 device-2 temperature:
(sensor value > 70) is system major alarm
module 5 power-output-fail: OK

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-701

show environment alarm

threshold #1 for module 5 power-output-fail:

(sensor value != 0) is system major alarm
module 5 outlet temperature: 26C
threshold #1 for module 5 outlet temperature:
(sensor value > 60) is system minor alarm
threshold #2 for module 5 outlet temperature:
(sensor value > 75) is system major alarm
module 5 inlet temperature: 23C
threshold #1 for module 5 inlet temperature:
(sensor value > 50) is system minor alarm
threshold #2 for module 5 inlet temperature:
(sensor value > 65) is system major alarm
EARL 1 outlet temperature: N/O
threshold #1 for EARL 1 outlet temperature:
(sensor value > 60) is system minor alarm
threshold #2 for EARL 1 outlet temperature:
(sensor value > 75) is system major alarm
EARL 1 inlet temperature: N/O
threshold #1 for EARL 1 inlet temperature:
(sensor value > 50) is system minor alarm
threshold #2 for EARL 1 inlet temperature:
(sensor value > 65) is system major alarm
Router>

Related Commands

Command

Description

show environment
status

Displays the information about the operational FRU status.

show environment
temperature

Displays the current temperature readings.

Cisco IOS Configuration Fundamentals Command Reference

CF-702

April 2010

show environment cooling

show environment cooling

To display the information about the cooling parameter, use the show environment cooling command
in user EXEC or privileged EXEC mode.
show environment cooling

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

This command is not supported in Cisco 7600 series routers that are configured with a Supervisor
Engine 2.

Examples

This example shows how to display the information about the cooling parameter:
Router> show environment cooling
fan-tray 1:
fan-tray 1 fan-fail: failed
fan-tray 2:
fan 2 type: FAN-MOD-9
fan-tray 2 fan-fail: OK
chassis cooling capacity: 690 cfm
ambient temperature: 55C
chassis per slot cooling capacity: 75 cfm
module
module
module
module
module
module
Router>

Related Commands

1
2
5
6
8
9

cooling
cooling
cooling
cooling
cooling
cooling

requirement:
requirement:
requirement:
requirement:
requirement:
requirement:

70
70
30
70
70
30

cfm
cfm
cfm
cfm
cfm
cfm

Command

Description

hw-module fan-tray version

Sets the fan-type (high or low power) version.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-703

show environment status

show environment status

To display the information about the operational FRU status, use the show environment status
command in user EXEC or privileged EXEC mode.
show environment status [frutype]

Syntax Description

frutype

Defaults

If you do not enter a frutype, all FRU status information is displayed.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(18)SXF

The output of the show environment status power-supply command was

changed to include information about the high-capacity power supplies.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

Note

(Optional) FRU type; see the Note for a list of valid values.

Valid values for the frutype are as follows:

allNo arguments.

backplaneNo arguments.

clock number1 and 2.

earl slotSee the Note for valid values.

fan-trayNo arguments.

module slotSee the Note for valid values.

power-supply number1 and 2.

rp slotSee the Note for valid values.

supervisor slotSee the Note for valid values.

vtt number1 to 3.

The slot argument designates the module and port number. Valid values for slot depend on the chassis
and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is
installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the
port number are from 1 to 48.

Cisco IOS Configuration Fundamentals Command Reference

CF-704

April 2010

show environment status

Examples

This example shows how to display the information about the environmental status:
Router> show environment status
backplane:
operating clock count: 2
operating VTT count: 3
fan-tray:
fantray fan operation sensor: OK
VTT 1:
VTT 1 OK: OK
VTT 2:
VTT 2 OK: OK
VTT 3:
VTT 3 OK: OK
clock 1:
clock 1 OK: OK, clock 1 clock-inuse: not-in-use
clock 2:
clock 2 OK: OK, clock 2 clock-inuse: in-use
power-supply 1:
power-supply 1 fan-fail: OK
power-supply 1 power-output-fail: OK
module 1:
module 1 power-output-fail: OK
module 1 outlet temperature: 21C
module 1 inlet temperature: 25C
module 1 device-1 temperature: 30C
module 1 device-2 temperature: 29C
EARL 1 outlet temperature: N/O
EARL 1 inlet temperature: N/O
module 5:
module 5 power-output-fail: OK
module 5 outlet temperature: 26C
module 5 inlet temperature: 23C
module 5 device-1 temperature: 26C
module 5 device-2 temperature: 27C
Router>

This example shows how to display the information about the high-capacity power supplies:
Route># show environment status power-supply 2
power-supply 2:
power-supply 2
power-supply 2
power-supply 2
power-supply 2
power-supply 2
power-supply 2
power-supply 2

fan-fail: OK
power-input 1: none
power-input 2: AC low
power-input 3: AC high
power-input 4: AC high
power-output: low (mode 1)
power-output-fail: OK

Table 86 describes the fields that are shown in the example.

Table 86

show environment status Command Output Fields

Field

Description

operating clock count

Physical clock count.

operating VTT count

Physical VTT count.

fan tray fan operation sensor

System fan tray failure status. The failure of the system fan tray is
indicated as a minor alarm.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-705

show environment status

Table 86

Related Commands

show environment status Command Output Fields (continued)

Field

Description

VTT 1, VTT2, and VTT3

Status of the chassis backplane power monitors that are located on

the rear of the chassis, under the rear cover. Operation of at least two
VTTs is required for the system to function properly. A minor
system alarm is signaled when one of the three VTTs fails. A major
alarm is signaled when two or more VTTs fail and the supervisor
engine is accessible through the console port.

clock # clock-inuse

Clock status. Failure of either clock is considered to be a minor

alarm.

power-supply # fan-fail

Fan failure. Fan failures on either or both (if any) power supplies are
considered minor alarms.

power-input-fail

Power input failure status (none, AC high, AC low).

power-output-fail

Power output failure status (high, low).

outlet temperature

Exhaust temperature value.

inlet temperature

Intake temperature value.

device-1 and device-2

temperature

Two devices that measure the internal temperature on each indicated

module. The temperature shown indicates the temperature that the
device is recording. The devices are not placed at an inlet or an exit
but are additional reference points.

Command

Description

show environment alarm

Displays the information about the environmental alarm.

show environment temperature

Displays the current temperature readings.

Cisco IOS Configuration Fundamentals Command Reference

CF-706

April 2010

show environment temperature

show environment temperature

To display the current temperature readings, use the show environment temperature command in user
EXEC or privileged EXEC mode.
show environment temperature [frutype]

Syntax Description

frutype

Defaults

If you do not enter a frutype, the module and EARL temperature readings are displayed.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17a)SX

The show environment temperature module command output was updated

to include the following information:

Usage Guidelines

(Optional) Field replaceable unit (FRU) type; see the Usage Guidelines section for a
list of valid values.

The name of the ASIC of this sensor.

The names of the ASIC are listed if there is more than one ASIC.

The type of sensor is listed if there is more than one sensor on the ASIC.

Current temperature.

Major/minor threshold as read in the IDPROM.

Status of whether the current temperature has exceeded any temperature

thresholds.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Valid values for the frutype are as follows:

earl slotSee the Note below for valid values.

module slotSee the Note below for valid values.

rp slotSee the the Note below for valid values.

vtt number1 to 3.

clock number1 and 2.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-707

show environment temperature

Note

The slot argument designates the module and port number. Valid values for slot depend on the chassis
and module that are used. For example, if you have a 48-port 10/100BASE-T Ethernet module that is
installed in a 13-slot chassis, valid values for the slot number are from 1 to 13 and valid values for the
port number are from 1 to 48.
The show environment temperature module command output includes the updated information after
an SCP response is received.
In the output display, the following applies:

Examples

N/O means not operationalThe sensor is broken, returning impossible values.

N/A means not availableThe sensor value is presently not available; try again later.

VTT 1, 2, and 3 refer to the power monitors that are located on the chassis backplane under the rear
cover.

This example shows how to display the temperature information for a specific module:
Router> show environment temperature module 5
module 5
module
module
module
module
module
module
module
module
module
Router>

outlet temperature: 34C

5 inlet temperature: 27C
5 device-1 temperature: 42C
5 device-2 temperature: 41C
5 asic-1 (SSO-1) temp: 29C
5 asic-2 (SSO-2) temp: 29C
5 asic-3 (SSO-3) temp: 29C
5 asic-4 (SSO-4) temp: 28C
5 asic-5 (SSA-1) temp: 29C
5 asic-6 (HYPERION-1) temp: 29C

This example shows how to display the temperature readings for all modules:
Router> show environment temperature
VTT 1 outlet temperature: 25C
VTT 2 outlet temperature: 24C
VTT 3 outlet temperature: 28C
module 1 outlet temperature: 24C
module 1 device-2 temperature: 29C
RP 1 outlet temperature: 25C
RP 1 inlet temperature: 29C
EARL 1 outlet temperature: 25C
EARL 1 inlet temperature: 22C
module 5 outlet temperature: 27C
module 5 inlet temperature: 22C
Router>

Table 87 describes the fields that are shown in the example.

Table 87

show environment temperature Command Output Fields

Field

Description

outlet temperature

Exhaust temperature value.

Cisco IOS Configuration Fundamentals Command Reference

CF-708

April 2010

show environment temperature

Table 87

Related Commands

show environment temperature Command Output Fields

Field

Description

inlet temperature

Intake temperature value.

device-1 and device-2 temperature

Two devices that measure the internal temperature on the

indicated module. The temperature shown indicates the
temperature that the device is recording. The devices are not
placed at an inlet or an exit but are additional reference points.

Command

Description

show environment alarm

Displays the information about the environmental alarm.

show environment status

Displays the information about the operational FRU status.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-709

show errdisable detect

show errdisable detect

To display the error-disable detection status, use the show errdisable detect command in user EXEC or
privileged EXEC mode.
show errdisable detect

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17b)SXA

This command was changed to include packet-buffer error status information.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Examples

This example shows how to display the error-disable detection status:

Router> show errdisable detect
ErrDisable Reason
----------------udld
bpduguard
rootguard
packet-buffer-err
pagp-flap
dtp-flap
link-flap
Router#

Related Commands

Command

Detection status
---------------Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled

Description

errdisable detect cause Enables the error-disable detection.

Cisco IOS Configuration Fundamentals Command Reference

CF-710

April 2010

show errdisable recovery

show errdisable recovery

To display the information about the error-disable recovery timer, use the show errdisable recovery
command in EXEC mode.
show errdisable recovery

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Examples

This example shows how to display the information about the error-disable recovery timer:
Router# show errdisable recovery
ErrDisable Reason
----------------udld
bpduguard
rootguard
pagp-flap
dtp-flap
link-flap

Timer Status
-------------Enabled
Enabled
Enabled
Enabled
Enabled
Enabled

Timer interval:300 seconds

Interfaces that will be enabled at the next timeout:
Interface
--------Fa9/4

Related Commands

Errdisable reason
----------------link-flap

Time left(sec)
-------------279

Command

Description

errdisable recovery

Configures the recovery mechanism variables.

show interfaces status

Displays the interface status or a list of interfaces in an error-disabled state

on LAN ports only.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-711

show fastblk

show fastblk
To display fast block memory information, use the show fastblk command in privileged EXEC mode.
show fastblk [detailed]

Syntax Description

detailed

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.4(22)T

This command was introduced.

(Optional) Displays detailed allocated fast block memory pool information.

Usage Guidelines

Use this command to display allocated fast block memory pool details. When no memory pools are
allocated, the no fastblk memory pools allocated message is displayed.

Examples

The following is sample output from the show fastblk command using the detailed keyword. The fields
are self-explanatory.
Router# show fastblk detailed
Pool name: SCTP ApplReq
flags:DYN_POOL
total = 400 inuse = 0, free = 400, max = 0
increment = 200, threshold = 100, hist max = 400
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62968A2C, total = 400, inuse= 0, free = 400
delete count = 0, flags:
Pool name: SCTP BufSegHdr
flags:DYN_POOL
total = 9000 inuse = 0, free = 9000, max = 0
increment = 4500, threshold = 6750, hist max = 9000
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62B8E2F4, total = 9000, inuse= 0, free = 9000
delete count = 0, flags:
Pool name: SCTP DestAddr
flags:DYN_POOL
total = 80 inuse = 0, free = 80, max = 0
increment = 40, threshold = 20, hist max = 80
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62972534, total = 80, inuse= 0, free = 80
delete count = 0, flags:
Pool name: SCTP Addr
flags:DYN_POOL POOL_HAS_GRWN
total = 200 inuse = 100, free = 100, max = 0
increment = 50, threshold = 50, hist max = 200
alloc failures = 31, sub-pool creation failures = 0
subpool: blks = 0x6271B6D0, total = 50, inuse= 0, free = 50
delete count = 0, flags: DYN_SUBPOOL
subpool: blks = 0x6271D730, total = 50, inuse= 0, free = 50
delete count = 0, flags: DYN_SUBPOOL
subpool: blks = 0x6297680C, total = 100, inuse= 100, free = 0
delete count = 0, flags:
Pool name: SCTP ChunkDesc
flags:DYN_POOL

Cisco IOS Configuration Fundamentals Command Reference

CF-712

April 2010

show fastblk

total = 9000 inuse = 0, free = 9000, max = 0

increment = 4500, threshold = 6750, hist max = 9000
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62BE6160, total = 1471, inuse= 0, free = 1471
delete count = 0, flags:
subpool: blks = 0x62D8D768, total = 7529, inuse= 0, free = 7529
delete count = 0, flags:
Pool name: SCTP DgramHdr
flags:DYN_POOL
total = 9000 inuse = 0, free = 9000, max = 0
increment = 4500, threshold = 6750, hist max = 9000
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62BFE848, total = 9000, inuse= 0, free = 9000
delete count = 0, flags:
Pool name: SCTP Assoc
flags:DYN_POOL
total = 100 inuse = 0, free = 100, max = 0
increment = 50, threshold = 25, hist max = 100
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62E0A778, total = 100, inuse= 0, free = 100
delete count = 0, flags:
Pool name: SCTP Instance
flags:DYN_POOL
total = 200 inuse = 50, free = 150, max = 0
increment = 100, threshold = 50, hist max = 200
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62C33434, total = 200, inuse= 50, free = 150
delete count = 0, flags:
Pool name: SCTP Assoc Stats
flags:DYN_POOL
total = 100 inuse = 0, free = 100, max = 0
increment = 50, threshold = 25, hist max = 100
alloc failures = 0, sub-pool creation failures = 0
subpool: blks = 0x62C39EA0, total = 100, inus

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-713

show file descriptors

show file descriptors

To display a list of open file descriptors, use the show file descriptors command in EXEC mode.
show file descriptors

Syntax Description

This command has no arguments or keywords.

Command Modes

EXEC

Command History

Release

Modification

11.3 AA

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

File descriptors are the internal representations of open files. You can use this command to learn if
another user has a file open.

Examples

The following is sample output from the show file descriptors command:
Router# show file descriptors
File Descriptors:
FD
0
1

Position
187392
184320

Open
0001
030A

PID
2
2

Path
tftp://dirt/hampton/c4000-i-m.a
flash:c4000-i-m.a

Table 88 describes the fields shown in the display.

Table 88

show file descriptors Field Descriptions

Field

Description

FD

File descriptor. The file descriptor is a small integer used to specify

the file once it has been opened.

Position

Byte offset from the start of the file.

Open

Flags supplied when opening the file.

PID

Process ID of the process that opened the file.

Path

Location of the file.

Cisco IOS Configuration Fundamentals Command Reference

CF-714

April 2010

show file information

show file information

To display information about a file, use the show file information command in EXEC mode.
show file information file-url

Syntax Description

file-url

Command Modes

EXEC

Command History

Release

Modification

11.3 AA

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Examples

The URL of the file to display.

The following is sample output from the show file information command:
Router# show file information tftp://dirt/hampton/c2500-j-l.a
tftp://dirt/hampton/c2500-j-l.a:
type is image (a.out) [relocatable, run from flash]
file size is 8624596 bytes, run size is 9044940 bytes [8512316+112248+420344]
Foreign image
Router# show file information slot0:c7200-js-mz
slot0:c7200-js-mz:
type is image (elf) []
file size is 4770316 bytes, run size is 4935324 bytes
Runnable image, entry point 0x80008000, run from ram
Router1# show file information nvram:startup-config
nvram:startup-config:
type is ascii text

Table 89 describes the possible file types.

Table 89

Possible File Types

Types

Description

image (a.out)

Runnable image in a.out format.

image (elf)

Runnable image in elf format.

ascii text

Configuration file or other text file.

coff

Runnable image in coff format.

ebcdic

Text generated on an IBM mainframe.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-715

show file information

Table 89

Possible File Types (continued)

Types

Description

lzw compression

Lzw compressed file.

tar

Text archive file used by the Channel Interface Processor (CIP).

Cisco IOS Configuration Fundamentals Command Reference

CF-716

April 2010

show file systems

show file systems

To list available file systems, use the show file systems command in privileged EXEC mode.
show file systems

Syntax Description

This command has no arguments or keywords.

Command Modes

Privileged EXEC

Command History

Release

Modification

11.3AA

This command was introduced.

12.3(7)T

This command was enhanced to display information about the ATA ROM
monitor library (monlib) file.

12.2(25)S

This command was integrated into Cisco IOS Release 12.2(25)S.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2(33)SXI

This command was integrated into Cisco IOS Release 12.2(33)SXI and the
output was modified.

12.4(24)T

This command was integrated into Cisco IOS Release 12.4(24)T and the
output was modified.

Usage Guidelines

Use this command to learn the alias names, the Prefixes column in the output of the file systems that
your router supports.

Examples

The following is sample output from the show file systems command:
Router# show file systems
File Systems:

Size(b)
42541056
512065536
65536000
129004
125802334
0
1964024
-

Free(b)
42541056
30834688
19811932
102228
0
609689428
1949453
-

Type
ram
opaque
disk
disk
flash
opaque
nvram
opaque
opaque
opaque
opaque
nvram
network
network
network
network

Flags
rw
rw
rw
rw
rw
ro
rw
ro
rw
rw
ro
rw
rw
rw
rw
rw

Prefixes
tmp:
system:
disk1: disk1:0:#
disk0:#
bootflash: sup-bootflash:
ivfs:
const_nvram:
microcode: sup-microcode:
image: sup-image:
null:
tar:
nvram:
rcp:
tftp:
http:
ftp:

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-717

show file systems

512065536
65536000
1964024
129004
65536000
-

30842880
19328264
1919757
102228
65536000
-

disk
disk
disk
disk
flash
nvram
nvram
flash
nvram
opaque
disk
disk
disk

rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw

disk1:1:
disk1:2:
slavedisk0:#
slavedisk1: slavedisk1:0:
slavesup-bootflash:
slavenvram:
slaveconst_nvram:
slavebootflash:
slavercsf:
slavesystem:
slavedisk1:1:
slavedisk1:2:
slavedisk1:3:

Table 90 describes the significant fields shown in the display.

Table 90

show file systems Field Descriptions

Field

Description

Size(b)

Amount of memory in the file system (in bytes).

Free(b)

Amount of free memory in the file system (in bytes).

Type

Type of file system. The file system can be one of the following
types:

Flags

Prefixes

diskThe file system is for a rotating medium.

flashThe file system is for a flash memory device.

networkThe file system is a network file system (TFTP, rcp,

FTP, and so on).

nvramThe file system is for an NVRAM device.

opaqueThe file system is a locally generated pseudo file

system (for example, the system) or a download interface,
such as brimux.

ramThe file system is for a RAM or EPROM device.

ttyThe file system is for a collection of terminal devices.

unknownThe file system is of unknown type.

Permissions for the file system. The file system can have one of the
following permission states:

roThe file system is Read Only.

woThe file system is Write Only.

rwThe file system is Read/Write.

Alias for the file system. Prefixes marked with a pound symbol (#)
indicate a bootable disk.

Cisco IOS Configuration Fundamentals Command Reference

CF-718

April 2010

show flh-log

show flh-log
The show flh-log command has been replaced by the more flh:logfile command. See the description of
the more flh:logfile command for more information.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-719

show fm inspect

show fm inspect
To display the list and status of the access control lists (ACLs) and ports on which context based access
control (CBAC) is configured, use the show fm inspect command in user EXEC or privileged EXEC
mode.
show fm inspect [detail | interface type mod/port]

Syntax Description

detail

(Optional) Displays all of the flow information.

interface type

Interface type; possible valid values are ethernet, fastethernet, gigabitethernet,

tengigabitethernet, port-channel, pos, atm, null, tunnel, and ge-wan.

mod/port

Module and port number.

Defaults

This command has no default settings.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Usage Guidelines

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

If you can configure a VLAN access control list (VACL) on the port before you configure CBAC, the
status displayed is INACTIVE; otherwise, it is ACTIVE. If policy feature card (PFC) resources are
exhausted, the command displays BRIDGE and is followed by the number of failed currently active
NetFlow requests that have been sent to the MSFC2 for processing.
The show fm inspect command output includes this information:

interface:Interface on which the internet protocol (IP) inspect feature is enabled

(direction)Direction in which the IP inspect feature is enabled (IN or OUT)

acl name:Name that is used to identify packets being inspected

status:(ACTIVE or INACTIVE) displays if HW-assist is provided for this interface+direction

(ACTIVE=hardware assisted or INACTIVE)

The optional detail keyword displays the ACEs that are part of the ACL that is used for IP inspect on
the given interface direction.

Examples

This example shows how to display the list and status of CBAC-configured ACLs and ports:
Router> show fm inspect

Cisco IOS Configuration Fundamentals Command Reference

CF-720

April 2010

show fm inspect

interface:Vlan305(in) status :ACTIVE

acl name:deny
interfaces:
Vlan305(out):status ACTIVE

Related Commands

Command

Description

show fm summary

Displays a summary of FM Information.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-721

show fm interface

show fm interface
To display the detailed information about the feature manager on a per-interface basis, use the show fm
interface command in user EXEC or privileged EXEC mode.
show fm interface {interface type mod/port | null interface-number | port-channel number | vlan
vlan-id}

Syntax Description

type

Interface type; possible valid values are ethernet, fastethernet, gigabitethernet,

tengigabitethernet, port-channel, pos, atm, null, tunnel, and ge-wan.

mod/port

Module and port number.

null
interface-number

Specifies the null interface; the valid value is 0.

port-channel
number

Specifies the channel interface; valid values are a maximum of 64 values ranging
from 1 to 282.

vlan vlan-id

Specifies the virtual local area network (VLAN); valid values are from 1 to 4094.

Defaults

This command has no default settings.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17a)SX

The order of the information that is displayed in the show fm interface vlan
command output was changed.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Usage Guidelines

The pos, atm, and ge-wan keywords are supported on Cisco 7600 series routers that are configured with
a Supervisor Engine 2.
The interface-number argument designates the module and port number. Valid values for
interface-number depend on the specified interface type and the chassis and module that are used. For
example, if you specify a Gigabit Ethernet interface and have a 48-port 10/100BASE-T Ethernet module
that is installed in a 13-slot chassis, valid values for the module number are from 1 to 13 and valid values
for the port number are from 1 to 48.
The port-channel number values from 257 to 282 are supported on the CSM and the FWSM only.

Cisco IOS Configuration Fundamentals Command Reference

CF-722

April 2010

show fm interface

Examples

This example shows how to display the detailed information about the feature manager on a specified
interface:
Router> show fm interface fastethernet 2/26
Interface:FastEthernet2/26 IP is enabled
hw[EGRESS] = 1, hw[INGRESS] = 0
hw_force_default[EGRESS] = 0, hw_force_default[INGRESS] = 1
mcast = 0
priority = 2
reflexive = 0
inbound label:24
protocol:ip
feature #:1
feature id:FM_IP_ACCESS
ACL:113
vmr IP value #1:0, 0, 0, 0, 0, 0, 0, 6 - 1
vmr IP mask #1:0, 0, FFFF, FFFF, 0, 0, 0, FF
vmr IP value #2:642D4122, 0, 0, 0, 1, 0, 0, 6 - 1
vmr IP mask #2:FFFFFFFF, 0, 0, 0, 1, 0, 0, FF
vmr IP value #3:0, 64020302, 0, 0, 6, 0, 0, 6 - 1
vmr IP mask #3:0, FFFFFFFF, 0, 0, 6, 0, 0, FF
vmr IP value #4:0, 64020302, 0, 0, A, 0, 0, 6 - 1
vmr IP mask #4:0, FFFFFFFF, 0, 0, A, 0, 0, FF
vmr IP value #5:0, 64020302, 0, 0, 12, 0, 0, 6 - 1
vmr IP mask #5:0, FFFFFFFF, 0, 0, 12, 0, 0, FF
vmr IP value #6:0, 0, 0, 0, 0, 0, 0, 0 - 2
vmr IP mask #6:0, 0, 0, 0, 0, 0, 0, 0
outbound label:3
protocol:ip
feature #:1
feature id:FM_IP_WCCP
Service ID:0
Service Type:0
Router>

This example shows how to display the detailed information about the feature manager on a specific
VLAN:
Router> show fm interface vlan 21
Interface: Vlan21 IP is disabled
hw_state[INGRESS] = not reduced, hw_state[EGRESS] = not reduced
mcast = 0
priority = 0
flags = 0x0
inbound label: 8
Feature IP_VACL:
----------------------------------------------------------------------------FM_FEATURE_IP_VACL_INGRESS i/f: Vl21 map name: test
=============================================================================
-----------------------------------------------------------IP Seq. No: 10 Seq. Result : VACL_ACTION_FORWARD_CAPTURE
-----------------------------------------------------------DPort - Destination Port SPort - Source Port Pro - Protocol
X - XTAG TOS - TOS Value Res - VMR Result
RFM - R-Recirc. Flag MRTNP - M-Multicast Flag R - Reflexive flag
- F-Fragment flag - T-Tcp Control N - Non-cachable
- M-More Fragments - P-Mask Priority(H-High, L-Low)
Adj. - Adj. Index T - M(Mask)/V(Value) FM - Flow Mask
NULL - Null FM SAO - Source Only FM DAO - Dest. Only FM
SADA - Sour.& Dest. Only VSADA - Vlan SADA Only FF - Full Flow
VFF - Vlan Full Flow F-VFF - Either FF or VFF A-VSD - Atleast VSADA

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-723

show fm interface

A-FF - Atleast FF A-VFF - Atleast VFF A-SON - Atleast SAO

A-DON - Atleast DAO A-SD - Atleast SADA SHORT - Shortest
A-SFF - Any short than FF A-EFF - Any except FF A-EVFF- Any except VFF
A-LVFF- Any less than VFF ERR - Flowmask Error
+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+
|Indx|T| Dest Ip Addr | Source Ip Addr|DPort|SPort|Pro|RFM|X|ToS|MRTNP|Adj.| FM |
+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+
1 V 22.2.2.2 21.1.1.1 0 0 0 --- 0 0 ----L ---- SHORT
M 255.255.255.255 255.255.255.255 0 0 0 000 0 0
TM_PERMIT_RESULT
2 V 32.2.2.2 31.1.1.1 0 0 0 --- 0 0 ----L ---- SHORT
M 255.255.255.255 255.255.255.255 0 0 0 000 0 0
TM_PERMIT_RESULT
3 V 0.0.0.0 0.0.0.0 0 0 0 --- 0 0 ----L ---- SHORT
M 0.0.0.0 0.0.0.0 0 0 0 000 0 0
TM_L3_DENY_RESULT
-----------------------------------------------------------IP Seq. No: 65536 Seq. Result : VACL_ACTION_DROP
-----------------------------------------------------------+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+
|Indx|T| Dest Ip Addr | Source Ip Addr|DPort|SPort|Pro|RFM|X|ToS|MRTNP|Adj.| FM |
+----+-+---------------+---------------+-----+-----+---+---+-+---+-----+----+------+
1 V 0.0.0.0 0.0.0.0 0 0 0 --- 0 0 ----L ---- SHORT
M 0.0.0.0 0.0.0.0 0 0 0 000 0 0
TM_PERMIT_RESULT
Router>

Related Commands

Command

Description

show fm summary

Displays a summary of FM Information.

Cisco IOS Configuration Fundamentals Command Reference

CF-724

April 2010

show fm reflexive

show fm reflexive
To display the information about the reflexive entry for the dynamic feature manager, use the show fm
reflexive command in privileged EXEC mode.
show fm reflexive

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Examples

This example shows how to display the information about the reflexive entry for the dynamic feature
manager:
Router# show fm reflexive
Reflexive hash table:
Vlan613:refacl, OUT-REF, 64060E0A, 64060D0A, 0, 0, 7, 783, 6
Router#

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-725

show fm summary

show fm summary
To display a summary of feature manager information, use the show fm summary command in user
EXEC or privileged EXEC mode.
show fm summary

Syntax Description

This command has no arguments or keywords.

Defaults

This command has no default settings.

Command Modes

User EXEC
Privileged EXEC

Command History

Release

Modification

12.2(14)SX

Support for this command was introduced on the Supervisor Engine 720.

12.2(17d)SXB

Support for this command on the Supervisor Engine 2 was extended to

Release 12.2(17d)SXB.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

Examples

This example shows how to display a summary of feature manager information:

Router> show fm summary
Current global ACL merge algorithm:BDD
Interface:FastEthernet2/10
ACL merge algorithm used:
inbound direction: ODM
outbound direction:BDD
TCAM screening for features is ACTIVE outbound
TCAM screening for features is ACTIVE inbound
Interface:FastEthernet2/26
ACL merge algorithm used:
inbound direction: ODM
outbound direction:BDD
TCAM screening for features is ACTIVE outbound
TCAM screening for features is INACTIVE inbound
.
.
.
Router>

Related Commands

Command

Description

show fm interface

Displays the detailed information about the feature manager

on a per-interface basis.

Cisco IOS Configuration Fundamentals Command Reference

CF-726

April 2010

show funi

show funi
To display the frame-based user-network interface information, use the show funi command in user
EXEC or privileged EXEC mode.
show funi {arp-server [atm atm-interface-number] | class-links {vpi/vci-value | vci-value |
connection-name} | ilmi-configuration | ilmi-status [atm atm-interface-number] | map | pvc
[vpi/vci-value | vci-value | connection-name | dbs | ppp] | route | traffic | vp [atm-vpi-number]
| vc [atm-vcd-number | connection-name | detail [prefix {interface | vc_name | vcd | vpi/vci}]
| interface atm atm-interface-number [connection-name | detail [prefix {interface | vc_name
| vcd | vpi/vci}]] | range lower-vcd-limit upper-vcd-limit [connection-name | detail [prefix
{interface | vc_name | vcd | vpi/vci}]] | interface atm atm-interface-number [connection-name
| detail [prefix {interface | vc_name | vcd | vpi/vci}]] | summary [atm
atm-interface-number]]}

Syntax Description

arp-server

Displays Asynchronous Transfer Mode (ATM) address resolution protocol

server table information.

atm
atm-interface-number

(Optional) Specifies the ATM interface and the ATM interface number.

class-links

Displays ATM VC-class links information.

vpi/vci-value

(Optional) Specifies the Virtual Path Identifier or Virtual Channel Identifier

(VPI/VCI) value (slash is mandatory).

vci-value

(Optional) Specifies the virtual circuit interface value.

connection-name

(Optional) Specifies the connection name.

ilmi-configuration

Displays the top-level Integrated Local Management Interface (ILMI)

information.

ilmi-status

Display ATM interface ILMI information.

map

Displays ATM static mapping information.

pvc

Displays ATM Permanent Virtual Circuits (PVC) information.

dbs

Displays the DBS information on a virtual circuit.

ppp

Displays the PPP over ATM information

route

Displays ATM route information.

traffic

Displays ATM statistics.

vp

Displays ATM virtual path information.

atm-vpi-number

(Optional) Specifies the VPI number.

vc

Displays ATM virtual circuit information.

atm-vcd-number

(Optional) Specifies the ATM Virtual Circuit Descriptor (VCD) number.

detail

Displays the detailed information of all VCs.

prefix

(Optional) Specifies the prefix for the output ordering.

interface

Specifies the type of interface. When this keyword is used along with the
prefix keyword it displays the interface values in ascending order.

vc_name

Displays the VC names in the alphabetical order.

vcd

Displays the VCD value in the ascending order.

vpi/vci

Displays the VPI/VCI value in the ascending order.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-727

show funi

range

Displays the range of VCs.

lower-vcd-limit

Specifies the lower limit VCD value.

upper-vcd-limit

Specifies the upper limit VCD value.

summary

Display summary of VCs.

Command Modes

User EXEC (>)

Privileged EXEC (#)

Command History

Release

Modification

12.4(24)T

This command was introduced.

Cisco IOS XE 2.3

This command was implemented on Cisco ASR 1000 series routers.

Usage Guidelines

Use this command to display the frame-based user-network interface information with the available
keywords and arguments.

Examples

The following is sample output from the show funi traffic command. The fields are self-explanatory:
Router# show funi traffic
Input OAM Queue: 0/4136 (size/max)
0 Input packets
0 Output packets
0 Broadcast packets
0 Packets received on non-existent VC
0 Packets attempted to send on non-existent VC
0 OAM cells received
F5 InEndloop: 0, F5 InSegloop: 0, F5 InAIS: 0, F5 InRDI: 0
F5 InEndcc: 0, F5 InSegcc: 0,
F4 InEndloop: 0, F4 InSegloop: 0, F4 InAIS: 0, F4 InRDI: 0
0 OAM cells sent
F5 OutEndloop: 0, F5 OutSegloop: 0,
F5 OutAIS: 0
F5 OutRDI: 0
F5 OutEndcc: 0, F5 OutSegcc: 0,
F4 OutEndloop: 0, F4 OutSegloop: 0,
F4 OutRDI: 0
F4 OutAIS: 0
0 OAM cell drops

The following is sample out from the show funi vc detail prefix interface command. The fields are
self-explanatory:
Router# show funi vc detail prefix interface
Description: N/A
ATM2/0 ATM2/0: VCD: 1, VPI: 1, VCI: 100
ATM2/0 UBR, PeakRate: 0 (0 cps)
ATM2/0 AAL5-LLC/SNAP, etype:0x0, Flags: 0xC20, VCmode: 0x0, Encapsize: 12
ATM2/0 OAM frequency: 0 second(s)
ATM2/0 InARP frequency: 15 minutes(s)
ATM2/0 Transmit priority 6
ATM2/0 InPkts: 0, OutPkts: 0, InBytes: 0, OutBytes: 0
InCells: 0, OutCells: 0
ATM2/0 InPRoc: 0, OutPRoc: 0, Broadcasts: 0
ATM2/0 InFast: 0, OutFast: 0, InAS: 0, OutAS: 0

Cisco IOS Configuration Fundamentals Command Reference

CF-728

April 2010

show funi

ATM2/0 InPktDrops: 0, OutPktDrops: 0

ATM2/0 CrcErrors: 0, SarTimeOuts: 0, OverSizedSDUs: 0, LengthViolation: 0, CPIE0
ATM2/0 Out CLP=1 Pkts: 0, Cells: 0
ATM2/0 OAM cells received: 0
ATM2/0 OAM cells sent: 0
ATM2/0 Status: INACTIVE
Description: N/A
ATM2/0 ATM2/0: VCD: 2, VPI: 1, VCI: 101
ATM2/0 UBR, PeakRate: 0 (0 cps)
ATM2/0 AAL5-LLC/SNAP, etype:0x0, Flags: 0xC20, VCmode: 0x0, Encapsize: 12
ATM2/0 OAM frequency: 0 second(s)

The following is sample out from the show funi vc detail prefix vc_name command. The fields are
self-explanatory:
Router# show funi vc detail prefix vc_name
Description: N/A
ATM2/0: VCD: 1, VPI: 1, VCI: 100
UBR, PeakRate: 0 (0 cps)
AAL5-LLC/SNAP, etype:0x0, Flags: 0xC20, VCmode: 0x0, Encapsize: 12
OAM frequency: 0 second(s)
InARP frequency: 15 minutes(s)
Transmit priority 6
InPkts: 0, OutPkts: 0, InBytes: 0, OutBytes: 0
InCells: 0, OutCells: 0
InPRoc: 0, OutPRoc: 0, Broadcasts: 0
InFast: 0, OutFast: 0, InAS: 0, OutAS: 0
InPktDrops: 0, OutPktDrops: 0
CrcErrors: 0, SarTimeOuts: 0, OverSizedSDUs: 0, LengthViolation: 0, CPIErrors: 0
Out CLP=1 Pkts: 0, Cells: 0
OAM cells received: 0
OAM cells sent: 0
Status: INACTIVE
Description: N/A
ATM2/0: VCD: 2, VPI: 1, VCI: 101
UBR, PeakRate: 0 (0 cps)
AAL5-LLC/SNAP, etype:0x0, Flags: 0xC20, VCmode: 0x0, Encapsize: 12
OAM frequency: 0 second(s)
InARP frequency: 15 minutes(s)

The following is sample out from the show funi vc detail prefix pvi/vci command. The fields are
self-explanatory:
Router# show funi vc detail prefix vpi/vci
Description: N/A
VPI/VCI: 1/100 ATM2/0: VCD: 1, VPI: 1, VCI: 100
VPI/VCI: 1/100 UBR, PeakRate: 0 (0 cps)
VPI/VCI: 1/100 AAL5-LLC/SNAP, etype:0x0, Flags: 0xC20, VCmode: 0x0, Encapsize: 2
VPI/VCI: 1/100 OAM frequency: 0 second(s)
VPI/VCI: 1/100 InARP frequency: 15 minutes(s)
VPI/VCI: 1/100 Transmit priority 6
VPI/VCI: 1/100 InPkts: 0, OutPkts: 0, InBytes: 0, OutBytes: 0
InCells: 0, OutCells: 0
VPI/VCI: 1/100 InPRoc: 0, OutPRoc: 0, Broadcasts: 0
VPI/VCI: 1/100 InFast: 0, OutFast: 0, InAS: 0, OutAS: 0
VPI/VCI: 1/100 InPktDrops: 0, OutPktDrops: 0
VPI/VCI: 1/100 CrcErrors: 0, SarTimeOuts: 0, OverSizedSDUs: 0, LengthViolation:0
VPI/VCI: 1/100 Out CLP=1 Pkts: 0, Cells: 0
VPI/VCI: 1/100 OAM cells received: 0
VPI/VCI: 1/100 OAM cells sent: 0
VPI/VCI: 1/100 Status: INACTIVE
Description: N/A

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-729

show funi

VPI/VCI: 1/101 ATM2/0: VCD: 2, VPI: 1, VCI: 101

VPI/VCI: 1/101 UBR, PeakRate: 0 (0 cps)
VPI/VCI: 1/101 AAL5-LLC/SNAP, etype:0x0, Flags: 0xC20, VCmode: 0x0, Encapsize: 2

Cisco IOS Configuration Fundamentals Command Reference

CF-730

April 2010

show identity policy

show identity policy

To display identity policy information in a tabular form, use the show identity policy command in
privileged EXEC mode.
show identity policy [name]

Syntax Description

name

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(18)SX

This command was introduced.

Examples

(Optional) Name of the identity policy.

The following is output from the show identity policy command:

Router# show identity policy
Policy Name
ACL
Redirect ACL
Redirect URL
===============================================================================
p1
some-acl
NONE
NONE
p2
another-acl
redirect-acl
http://www.foo.com/bar.html
Router#

The following is output for the policy named p2:

Router# show identity policy p2
Name: p2
Description: NONE
Access-Group: another-acl
URL-Redirect Match ACL: redirect-acl
URL-Redirect URL: http://www.foo.com/bar.html
Router#

Related Commands

Command

Description

show running-configuration

Displays the running configuration for a router.

Cisco IOS Configuration Fundamentals Command Reference

April 2010

CF-731

show identity profile

show identity profile

To display identity profile information in a tabular form, use the show identity profile command in
privileged EXEC mode.
show identity profile [ default | dot1x | eapoudp]

Syntax Description

default

(Optional) Displays default identity profile information.

dot1x

(Optional) Displays 802.1x identity profile information.

eapoudp

(Optional) Displays EAPoUDP identity profile information.

Command Modes

Privileged EXEC (#)

Command History

Release

Modification

12.2(18)SX

This command was introduced.

Examples

The following is output from the show identity profile command:

Router# show running identity profile
Service Type: default
Default Authorized Device Policy: NONE
Default Non-Authorized Device Policy: NONE
Device / Address / Mask
Allowed
Policy
==============================================================
Cisco IP Phone
Authorized
DEFAULT
Service Type: dot1x
Default Authorized Device Policy: NONE
Default Non-Authorized Device Policy: NONE
Device / Address / Mask
Allowed
Policy
==============================================================
0001.0203.0405 /
ffff.ffff.ffff
Authorized
p2
Service Type: eapoudp
Device / Address / Mask
Allowed
Policy
==============================================================
10.0.0.0
/ 255.0.0.0
Authorized
p1
Router#

Related Commands

Command

Description

show running-configuration

Displays the running configuration for a router.

Cisco IOS Configuration Fundamentals Command Reference

CF-732

April 2010