Scribd
Upload
387 views

Valve Selection Handbook - Introduction

This document introduces the topics that will be covered in a book about selecting valves for piping systems. It explains that valve selection is based on several factors like function, material suitability, pressure and temperature requirements, and cost. It provides an overview of the types of valves that will be discussed, including manual valves, check valves, pressure relief valves, and rupture discs. It also outlines the chapters that will cover valve fundamentals, specific valve groups, units of measurement, identification standards, and additional topics not in previous editions. The purpose is to assist engineers in choosing the correct valve for a given application based on its design criteria.

Uploaded by

Palazzo345
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
387 views

Valve Selection Handbook - Introduction

This document introduces the topics that will be covered in a book about selecting valves for piping systems. It explains that valve selection is based on several factors like function, material suitability, pressure and temperature requirements, and cost. It provides an overview of the types of valves that will be discussed, including manual valves, check valves, pressure relief valves, and rupture discs. It also outlines the chapters that will cover valve fundamentals, specific valve groups, units of measurement, identification standards, and additional topics not in previous editions. The purpose is to assist engineers in choosing the correct valve for a given application based on its design criteria.

Uploaded by

Palazzo345
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

1

INTRODUCTION

The purpose of this book is to assist the Piping Specifying Engineer in


the selection of valves for a specific application and that meet the design
parameters of the process service. Valve selection is based on function,
material suitability, design pressure/temperature extremities, plant life, end
connections, operation, weight, availability, maintenance, and cost. I have
deliberately placed cost at the end for a reason. If the valve does not meet
the design criteria, then even if it is free, it is still too expensive, because of
the costs to replace it when it fails. Just like life, valve selection is a series
of compromises.
Valves are the components in a fluid flow or pressure system that regulate
either the flow or the pressure of the fluid. This duty may involve stopping
and starting flow, controlling flow rate, diverting flow, preventing back
flow, controlling pressure, or relieving pressure.
These duties are performed by adjusting the position of the closure
member in the valve. This may be done either manually or automatically.
Manual operation also includes the operation of the valve by means of a
manually controlled power operator. The valves discussed here are manually operated valves for stopping and starting flow, controlling flow rate,
and diverting flow; and automatically operated valves for preventing back
flow and relieving pressure. The manually operated valves are referred to
as manual valves, while valves for the prevention of back flow and the
relief of pressure are referred to as check valves and pressure relief valves,
respectively.

Valve Selection Handbook

Rupture discs are non-reclosing pressure-relieving devices which fulfill


a duty similar to pressure relief valves.

Fundamentals
Sealing performance and flow characteristics are important aspects in
valve selection. An understanding of these aspects is helpful and often
essential in the selection of the correct valve. Chapter 2 deals with the
fundamentals of valve seals and flow through valves.
The discussion on valve seals begins with the definition of fluid tightness,
followed by a description of the sealing mechanism and the design of seat
seals, gasketed seals, and stem seals. The subject of flow through valves
covers pressure loss, cavitation, waterhammer, and attenuation of valve
noise.

Manual Valves
9
9
9
9

Stopper type closure~globe, needle


Vertical slide~gate
Rotary type~ball, plug, butterfly
Flexible body~diaphragm

Manual valves are divided into four groups according to the way the
closure member moves onto the seat. Each valve group consists of a
number of distinct types of valves that, in turn, are made in numerous
variations.
The way the closure member moves onto the seat gives a particular
group or type of valve a typical flow-control characteristic. This flowcontrol characteristic has been used to establish a preliminary chart for
the selection of valves. The final valve selection may be made from the
description of the various types of valves and their variations that follow
that chart.
Note: For literature on control valves, refer to footnote on page 5 of this
book.

Check Valves
9 Lift check
9 Swing check (single and double plate)

Introduction

9 Tilting disc
9 Diaphragm
The many types of check valves are also divided into four groups
according to the way the closure member moves onto the seat.
The basic duty of these valves is to prevent back flow. However, the
valves should also close fast enough to prevent the formation of a significant reverse-flow velocity, which on sudden shut-off, may introduce
an undesirably high surge pressure and/or cause heavy slamming of the
closure member against the seat. In addition, the closure member should
remain stable in the open valve position.
Chapter 4, on check valves, describes the design and operating characteristics of these valves and discusses the criteria upon which check valves
should be selected.

Pressure Relief Valves


9 Direct-loaded pressure relief valves
9 Piloted pressure relief valves
Pressure relief valves are divided into two major groups: direct-acting
pressure relief valves that are actuated directly by the pressure of the system
fluid, and pilot-operated pressure relief valves in which a pilot controls the
opening and closing of the main valve in response to the system pressure.
Direct-acting pressure may be provided with an auxiliary actuator that
assists valve lift on valve opening and/or introduces a supplementary closing force on valve reseating. Lift assistance is intended to prevent valve
chatter while supplementary valve loading is intended to reduce valve simmer. The auxiliary actuator is actuated by a foreign power source. Should
the foreign power source fail, the valve will operate as a direct-acting
pressure relief valve.
Pilot-operated pressure relief valves may be provided with a pilot that
controls the opening and closing of the main valve directly by means of an
internal mechanism. In an alternative type of pilot-operated pressure relief
valve, the pilot controls the opening or closing of the main valve indirectly
by means of the fluid being discharged from the pilot.
A third type of pressure relief valve is the powered pressure relief valve in
which the pilot is operated by a foreign power source. This type of pressure
relief valve is restricted to applications only that are required by code.

Valve Selection Handbook

Rupture Discs
Rupture discs are non-reclosing pressure relief devices that may be used
alone or in conjunction with pressure relief valves. The principal types of
rupture discs are forward domed types, which fail in tension, and reverse
buckling types, which fail in compression. Of these types, reverse buckling
discs can be manufactured to close burst tolerances. On the debit side,
not all reverse buckling discs are suitable for relieving incompressible
fluids.
While the application of pressure relief valves is restricted to relieving
nonviolent pressure excursions, rupture discs may be used also for relieving
violent pressure excursions resulting from the deflagration of flammable
gases and dust. Rupture discs for deflagration venting of atmospheric
pressure containers or buildings are referred to as vent panels.

Units of Measurement
Measurements are given in SI and imperial units. Equations for solving
in customary but incoherent units are presented separately for solution
in SI and imperial units as presented customarily by U.S. manufacturers.
Equations presented in coherent units are valid for solving in either SI or
imperial units.

Identification of Valve Size and Pressure Class


The identification of valve sizes and pressure classes in this book follows
the recommendations contained in MSS Standard Practice SP-86. Nominal
valve sizes and pressure classes are expressed without the addition of units
of measure; e.g., NPS 2, DN 50 and Class 1 50, PN 20. NPS 2 stands for
nominal pipe size 2 in. and DN 50 for diameter nominal 50 mm. Class 150
stands for class 150 lb. and PN 20 for pressure nominal 20 bar.

Standards
Appendix C contains the more important U.S., British, and ISO standards
pertaining to valves. The standards are grouped according to valve type or
group.

Introduction

Additional Chapters
There are three additional chapters in the fifth edition of the Valve
S e l e c t i o n H a n d b o o k that have not been included previously:
Chapter 8 ~ A c m a t o r s
Chapter 9 ~ D o u b l e Block and Bleed Ball Valves
Chapter 1 0 ~ M e c h a n i c a l Locking Devices for Valves
A comprehensive glossary has also been included in A p p e n d i x E to
assist the reader.

This book does not deal with control valves. Readers interested in this field should consult
the following publications of the ISA:
1. Control Valve Primer, A User's Guide (3rd edition, 1998), by H. D. Baumann.

This book contains new material on valve sizing, smart (digital) valve positioners,
field-based architecture, network system technology, and control loop performance
evaluation.
2. Control Valves, Practical Guides for Measuring and Control (lst edition, 1998),
edited by Guy Borden. This volume is part of the Practical Guide Series, which has
been developed by the ISA. The last chapter of the book deals also with regulators and
compares their performance against control valves. Within the Practical Guide Series,
separate volumes address each of the important topics and give them comprehensive
treatment.
Address: ISA, 67 Alexander Drive, Research Triangle Park, NC 27709, USA. Email
http://www.isa.org

You might also like