!

!
!

!
!

AMBR!
AMATIS Border Router!

User Manual!

!
!

!
!
Last updated: June 2016

v4.3

!
!
!
!

TABLE OF CONTENTS!

!
!

INTRODUCTION!
BEFORE YOU START!
NETWORK FIREWALL REQUIREMENTS!

1.0
1.1
1.2

INSTALLING AMBR!
TROUBLESHOOTING AMBR CONNECTIVITY!
AMBR INDICATOR LIGHTS!

2.0
2.1
2.2

!
3.0
4.0

AGENCY CERTIFICATIONS
END USER LICENSE AGREEMENT

!
!

!
CUSTOMER SUPPORT!
970-300-1344!
[email protected]!

pg.2

v4.3

!
1.0

INTRODUCTION!

Thank you for choosing Amatis Controls. This AMBR User

Manual will guide you through the process of installing and using
the Amatis Border Router (AMBR). AMBR allows your system to
report valuable energy data to your Energy Dashboard, which is \
accessible online. All components must be installed correctly to
ensure the overall accuracy of this kit.!

1.1

BEFORE YOU START!

Before beginning installation, make sure the installation site has:!

a. High speed Internet connection (configured for DHCP)
b. Ethernet and electric outlets, within 200 feet of AMBR.
Please note AMBR can also be configured to use a static IP
address.

!
1.2

NETWORK FIREWALL REQUIREMENTS!

TCP 1195 outbound to vpn.amatiscontrols.com

UDP 1195 outbound to vpn.amatiscontrols.com
TCP 3306 outbound to sql.amatiscontrols.com
TCP 80 outbound to checkip.dyndns.org
TCP 80 outbound to vpn.amatiscontrols.com
TCP 80 outbound to api.amatiscontrols.com
TCP 80 outbound to dash.amatiscontrols.com

pg.3

v4.3

INSTALLING AMBR!

2.0

AMBR connects your Amatis system to the Internet. Follow the

steps below:!

1.
2.

Connect one end of the blue Cat5/Ethernet wire to the

back of AMBR.
Connect the other end of the blue Cat5/Ethernet wire to
an available Ethernet port.

NOTE: Some cable & DSL modems have only one Ethernet port. In order to
connect AMBR you may need to add another Ethernet port. Ethernet
Switches are available to add more Ethernet ports to the same Internet
connection. One option is illustrated below:

!
3.

pg.4

Plug the barrel end of the white 5V power supply into the
back of AMBR, then the plug into the wall socket.

v4.3

!
4.

5.

6.

Wait for 1-2 minutes while AMBR completes its startup

sequence and connects to the Internet. The startup LED
sequence is as follows:
a. red led, power GOOD
b. white led, AMBR started
c. blue led, hardware GOOD
d. yellow led, networking possible
e. green led blinking, loading software
On the front of AMBR a solid green light confirm AMBR
has booted up correctly and is connected to the Internet.
Startup sequence is complete, refer to section 2.2 for
descriptions of regular LED functions.
If AMBR does not show a blue light after 5 minutes, you
may be experiencing an Internet connectivity problem.
Follow the troubleshooting steps in the next section.
TROUBLESHOOTING AMBR CONNECTIVITY!

2.1

1.

Restart your modem and AMBR.

a. Power both devices off
b. Power modem on
c. After modem reboots and shows Internet activity
d. Plug AMBR back in
e. Verify AMBR shows blue blinking light
2. Confirm your modem is configured in DHCP mode
a. Follow modem owners manual directions
b. Contact your Internet service provider
3. Identify which AMBR indicator lights are active.
NOTE: When AMBR is connected to power, all lights turn on, then turn off,
then turn back on one-by-one. Indicators can be diagnosed in the table
below:

pg.5

v4.3

!
AMBR INDICATOR LEDS!

2.2

!
!

LED

Green

Orange

Blue

Red

Processor boot-up
SUCCESS

Processor
ERROR

Off Line data logging

SUCCESS

Off line logging

ERROR

Data logging and

configuration enabled
SUCCESS

Off

Solid

Processor boot-up
SUCCESS

White

Flashing

Data logging enabled

SUCCESS

Internet connection
ERROR

Normal operation

Power connection
SUCCESS

Power connection
ERROR

!
NOTE: this table is only valid after AMBR has completed its startup
sequence and the green LED is solid.!

!
!
!

pg.6

v4.3

3.0 AGENCY CERTIFICATIONS!

Operating Requirements and Conditions
The design of AMBR complies with FCC and IC safety levels of radio
frequency (RF) exposure for Mobile devices.
Mobile Device RF Exposure Statement
RF Exposure - This device is only authorized for use in a mobile application.
At least 20 cm of separation distance between the AMBR device and the
user's body must be maintained at all times.
Caution Statement for Modifications
CAUTION: Any changes or modifications not expressly approved by Amatis
Controls, LLC could void the users authority to operate the equipment.
FCC Notices
AMBR has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in an
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning AMBR off and on the user is
encouraged to try to correct the interference by one or more of the following
measures:

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer for help.

pg.7

v4.3

!
OEM Labeling Requirements
WARNING! The Original Equipment Manufacturer (OEM) must ensure that
FCC/IC labeling requirements are met. This includes a clearly visible label on
the outside of the final product enclosure that displays the contents shown
below.
FCC:
Contains FCC ID: 2ADDY-BR1
The enclosed device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.
this device may not cause harmful interference, and
2.
this device must accept any interference received,
including interference that may cause undesired
operation
IC:
Contains Model AMBR, IC:20256-BR1
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions:
1.
this device may not cause interference, and
2.
this device must accept any interference, including
interference that may cause undesired operation of
the device

pg.8

v4.3

!
Exigences et conditions de fonctionnement:
La conception de AMBR est conforme aux limites d'exposition aux
Frequences Radio dfinies par les normes IC et FCC pour les appareils
mobiles.
Dclaration d'exposition aux frquences radio d'appareil mobile
Exposition frquences radio - Cet appareil est seulement conu pour usage
mobile. Au moins 20 cm de sparation doit tre maintenue tout instant
entre l'appareil AMBR et l'utilisateur.
Dclaration de mise en garde concernant les modifications
ATTENTION: Tous changements ou modifications qui ne sont pas
expressment approuvs par Amatis Controls, LLC sont susceptibles de
rvoquer les droits d'utilisation de cet quipement.
Avis IC
AMBR a t test et entre dans la catgorie des appareils numriques de
Classe B, selon la Section 15 de la rglementation de la IC. Ces limites ont
t conues pour protger les installations domestiques contre les
interfrences nfastes. Cet quipement gnre, utilise et met de l'nergie
sous forme de frquences radio et, en cas de non-respect des instructions
d'installation et d'utilisation, risque de provoquer des interfrences radio. Il
n'existe cependant aucune garantie contre ces interfrences.
En cas d'interfrences radio ou tlvisuelles, pouvant tre vrifies en
allumant, puis en teignant l'quipement, l'utilisateur est invit essayer de
rsoudre le problme de l'une des faons suivantes :

Eloigner l'quipement du poste de rception ;

Brancher l'quipement sur une prise appartenant un circuit

diffrent de celui du rcepteur ;

Demander de l'aide auprs du revendeur ou d'un technicien

radio/TV

pg.9

v4.3

!
Exigences en matire d'tiquetage OEM :
ATTENTION! Le fabricant d'quipement d'origine (OEM) doit veiller ce que
les exigences en matire d'tiquetage de la FCC / IC soient respectes.
Cela comprend une tiquette clairement visible sur l'extrieur de l'enceinte
du produit final qui affiche le contenu ci-dessous.
IC:
Contient le model AMBR, IC:20256-BR1
Cet appareil respecte le(s) standard(s) RSS de l'Industry Canada
sans license. Pour cela le sujet doit respecter les deux
conditions suivantes:
1.
cet appareil ne doit pas causer des interfrences, et
2.
cet appareil doit supporter toute interfrence,
incluant des interfrences pouvant dclencher des
fonctionnements indsirables de lappareil

!
!
!
!
!
!
!
!
!
!
!

pg.10

v4.3

END USER SOFTWARE LICENSE AGREEMENT!

4.0

1. USER NOTICE
Please read this End User Software License Agreement (License
Agreement) carefully before using your Amatis product. By installing and
registering an Amatis device you hereby agree with the terms of this License
Agreement. If you do not agree with the terms of this License Agreement, do
not use the Amatis Product and Amatis Software.

2. TERMS
The terms of this License Agreement are applicable to anyone who uses
Amatis Controls Software and Firmware included in a product purchased
from Amatis and/or Amatis partners. This license does not permit the use of
the Amatis Software in any other product. Amatis Controls reserves the right
to take legal action against anyone else using, selling or distributing the
software. By using the Amatis Product and Amatis Software, you agree to the
terms of this License Agreement.

3. LICENSE
Amatis Controls grants a single, non-sublicensable, non-exclusive, nontransferable license to use the Amatis Software solely as part of products
obtained from Amatis and/or any Amatis partner for which applicable fees
have been paid. Except for the limited license rights expressly granted in this
License Agreement, Amatis Controls reserves all rights in and to the Amatis
Software and any modifications or copies thereto.

4. GENERAL RESTRICTIONS
In exchange for the license, you agree not to: decompile, disassemble, or
reverse engineer the Amatis Software; alter, modify or create any derivative
works based on the Amatis Software; use, copy, sell, sublicense, lease, rent,
loan, assign, convey or otherwise transfer the Amatis Software except as
expressly authorized in writing by Amatis Controls; distribute, disclose, or
allow use of the Amatis Software, in any format, through any timesharing
service, service bureau, network or by any other means; allow any service
provider or other third party, with the exception of Amatis Controls authorized
resellers, distributors, and their designated employees who are acting solely
on behalf of and for the benefit of the end user, to use or execute any

pg.11

v4.3

!
software commands that cause the Amatis Software to perform functions that
facilitate the maintenance or repair of any product.

5. DISCLAIMER OF WARRANTIES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, AMATIS
CONTROLS PROVIDES THE AMATIS SOFTWARE AS IS AND AS
AVAILABLE WITH ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND.
AMATIS CONTROLS HEREBY DISCLAIMS WITH RESPECT TO THE AMATIS
SOFTWARE ALL WARRANTIES AND CONDITIONS, WHETHER EXPRESS,
IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO ANY (IF ANY)
WARRANTIES OR CONDITIONS OF OR RELATED TO: NONINFRINGEMENT, MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, LACK OF VIRUS, ACCURACY, OR COMPLETENESS OF
RESPONSE.

6. TERMINATION
If you breach the license limitations or restrictions in this License Agreement,
Amatis Controls may, with immediate effect, terminate the software licenses
granted in this License Agreement without prejudice to any available rights
and remedies. Upon termination or expiration of the license for any reason,
you shall immediately return the Amatis Software and any copies to Amatis
Controls, or, at Amatis Controls discretion, you shall permanently destroy all
copies of the Amatis Software and any related materials in your possession or
control. Inadvertent copies of the Amatis Software and any related materials
remaining in the possession of the End User subsequent to termination or
expiration shall not be implied or construed as Amatis Controls consenting to
transfer ownership of the software and any related materials to the End User.

7. LIMITATION OF LIABILITY
TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT
SHALL AMATIS CONTROLS BE LIABLE FOR ANY CONSEQUENTIAL,
INDIRECT, SPECIAL, EXEMPLARY, OR PUNITIVE DAMAGES WHATSOEVER
(INCLUDING BUT NOT LIMITED TO DAMAGES FOR: LOSS OF PROFITS,
LOSS OF CONFIDENTIAL OR OTHER INFORMATION, BUSINESS
INTERRUPTION) ARISING OUT OF OR IN ANY WAY RELATED TO THE USE
OF OR INABILITY TO USE THE AMATIS SOFTWARE, EVEN IF AMATIS
CONTROLS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.

pg.12

v4.3

8. COMPLIANCE
Amatis Controls will have the right to inspect your compliance with these
License Agreement terms.

9. GOVERNMENT END USERS

The Amatis Software is classified as commercial computer software and the
Documentation is classified as commercial software documentation or
commercial items. Any use, modification, reproduction, release,
performance, display or disclosure of the Amatis Software or Documentation
shall be governed solely by the terms of this License Agreement and shall be
prohibited except to the extent expressly permitted.

10. APPLICABLE LAWS

This License Agreement will be governed by and construed in accordance
with the laws of the United States. Severability in the event that any part or
parts of this agreement shall be held illegal or null and void by any court or
administrative body of competent jurisdiction, such determination shall not
affect the remaining parts of this agreement, and they shall remain in full force
and effect as if such part or parts determined illegal or void had not been
included.

pg.13

v4.3