System Specification

ISO3171, API 8.2, IP 6.2 and ASTM

D4177 Fast Loop - Bypass loop

sampling system specification

ISO 3171 'Petroleum Liquids Automatic Pipeline Sampling. (1988)

API Manual of Petroleum Management

Standards Chapter 8 - Sampling Section 2 - 'Automatic Sampling of
Petroleum and Petroleum Products'.
(also published as ASTM-4177) (1995)

IP Petroleum Measurement Manual Part

VI Sampling - Section 2 - 'Automatic
Sampling of Liquids from Pipelines'.
(1986)

We promote the use of dynamic

performance monitoring (Can Weigh) which
is referenced by the sections of the standards
below.
The system complies with the requirements
of ISO 3171, IP 6.2 and API 8.2. Where
differences or conflict occur the higher
specification standard has been used. System
components which are required, or
recommended by the standards, are marked
with an asterisk (*)
It is assumed that the pipeline contents are
sufficiently mixed as per the C1/C2 ratio
requirements of the above standards. If not
refer to the relevant spec for JetMix system.

Standard

Reference Sections

ISO 3171

9, 14.3

API 8.2

19, Appendix F

IP 6.2

3.10, 8.3

Fast Loop - bypass loop sampling system specification

The products upon which these specifications

are based meet or exceed the requirements
of:

Fast Loop Sampling Equipment

All equipment marked as 'Withdrawable' is
designed for installation by 'hot-tapping' to
minimise the cost, time and impact on your
operating procedures
1) 1 off Jiskoot Withdrawable (Top Entry)
Byscoop
Fabricated from carbon steel, welded and
painted to Jiskoot standards. Inlet size 33mm
(designed with a droplet size/inlet ratio
according to ISO 3171) with an internal bevel
and 'swans neck' profile to reduce bluff body
effects and turbulence.
2) 1 off Jiskoot Fast Loop Sampling Skid
Substantial
carbon steel skid base, welded and painted to
Jiskoot standards, upon which the following
equipment would be mounted:
1 off Sampling Fast Loop
1", sized to provide a flow rate to maintain
mixing and dispersion within the Sampling Loop.
*
2 off Sampling Loop Isolation Valves
1" ANSI 150lb RF anti static fire safe full bore
ball valves to provide inlet and outlet isolation
for the Sampling Loop.These isolation valves
allow for the Sampling Loop to be isolated from
the CoJetix Pump loop and thus mixing can still
take place while maintenance is carried out on
the Sampling equipment if desired.
1 off Sampling System Enclosure
Designed to house the Cell Sampler, receivers
and all ancillaries (Cell Sampler, flow indicator
switch, two Sample Receivers, Receiver Weigh
Beam, Auto-changeover SOV, stainless steel
tube& fittings and junction boxes). There will be
a solenoid receiver changeover valve for
selecting the sample receiver in use. This
enables samples of 12 litres to be collected. It
includes two flexible hoses with quick connect

couplings and a drip tray. Also included within

the cabinet is a flow monitor with low flow
switch. Small-bore stainless steel tube would
generally be ". All internal cables would be
HOFR flexible.
1 off Flow Indicator Switch
Carbon steel "flapper" type flow meter with
switch to provide remote indication of either
low flow or high flow. Flanged ANSI 150lb RF
1 off Cell Sampler
Jiskoot 210P Cell Sampler Pneumatically
actuated positive displacement sampler, designed
to be installed between two 1" ANSI 150lb RF
flanges.The Cell Sampler is the same bore as the
sampling loop* and provides 1ml "grabs" * on
every actuation and with a maximum "grab" rate
of 100 per min. can sample 10 litres in under 2
hours*. The '3 step' grab action provides a
repeatability of +/-2%* regardless of variations
in viscosity or process conditions. Samples are
discharged from the bottom of the sampler to
avoid water traps and cross contamination. The
Cell sampler outlet is line balanced to maximise
operating life.
1 set Cell Sampler Ancillaries
Required ancillaries for a pneumatically operated
Series 210P Cell, including in-line relief valve,
flexible hose, fittings, EExm solenoid valve,
instrument air regulator and bracket to mount
and connect them.
2 off Sample Receivers
The Sample Receivers (type PR-53) have a
maximum capacity 18 litres, to be filled to a
maximum of 15 litres with allowance for 20%
ullage.*
They come complete with pressure indicator,
pressure relief valve and vacuum breaker. The
Sample Receivers have a large opening to allow
easy access for cleaning.

Manufactured from hygienic grade 304 stainless

steel with smooth internal surface for minimal
clingage. Each Sample Receiver weighs 6 lbs
dry and they are provided with connections for
external mixer loop*, for connection to a Jiskoot
Laboratory Mixer

Print option
This enables the print-out of a report at the end
of the batch.The report is stored in the
controller and is accessible until the next batch
is finished. A data log can also be generated
throughout the batch duration, logging up to 8
parameters.

1 off CanWeigh System

The Jiskoot CanWeigh System provides on-line
measurement of the sample mass in a receiver
and is used to continually monitor the
performance of the system*.
1 off Automatic Receiver Changeover System
Changeover is an additional function of a Can
Weigh System.The three way changeover valve
is pneumatically actuated by a supply switched
by the attached solenoid valve.This assembly
allows the selection of sample receiver in used
to be performed by the InSpec Controller.
3) 1 off Laboratory Mixer (MS-53E)
Electrically driven laboratory mixer to be used in
conjunction with a Jiskoot PR53 receiver.* The
laboratory mixer draws off the fluid from the
bottom of the receiver and pumps it through a
static mixer and then returns it back to the
receiver allowing a sub-sample to be drawn for
analysis.
4) 1 off InSpec Sample Controller (Safe Area)
The InSpec Sample Controller is used to control
the sampling process and can be supplied with
the following options.
Blend trim control
This feature is used to optimise final product
quality using an online analyser for parameters
such as sulphur, density or viscosity.
Pump and valve control
The InSpec blender is able to communicate with
a PLC and provide enhanced control of pumps
and block valves.
Batch quality calculations
Calculated and flow weighted averaging values
for mass, sulphur, viscosity and density.

Auxiliary control option

Provides automated control of a mixing or fast
loop pump or auxiliary equipment.
Modbus networking option
Enables full remote access operation as a
Modbus slave device supporting commands 03,
06 and 16.
Remote panel option
The controller front panel can be remotely
mounted up to 1km from the main instrument
and additional remote displays can be
connected.
The InSpec Sample Controller has the following
features;
Features

Operator entered flow or automatic

calculation of optimum set-point

Tuneable ramp up and down generator

Batch end optimisation of delivered

product

Integration into a clients DCS

Provides two tier alarms to warn or

shutdown due to ratio deviations

Blend enable input e.g. dead man's handle

Emergency Stop input

Configuration and storage of 20 recipes for

operator recall

Calculation of product and actual stream of

ratios, density, sulphur and viscosity
contents

Easy to read scrolling display with

configurable bar-graphs

Simple to use ergonomic controller

Front panel can be remotely mounted

Simple menu-driven wizard for ease of use

and configuration

PC based configuration backup and restore

feature
Operator and engineer security passwords
Integrated remote auxiliary control

5) 1 off Byscoop Extractor

Extraction device designed to safely insert or
withdraw the CoJetix Nozzle and Quill.

6) 1 off Inturbine Flowmeter

Insertion type flowmeter providing direct flow
rate measurement with 4-20mA output.
Capable of measuring velocities from 0.25 to 8
m/s at viscosities of 0.5 to 150 cSt. Constructed
from carbon steel seal housing and stainless
steel support tube & impellor. Flanged 6" ANSI
150lb RF. Withdrawable under live process
conditions when used in conjunction with a
Jiskoot Hydraulic Extractor.

Typical Fast Loop system

Jiskoot Limited - UK

Jiskoot Incorporated - USA

Goods Station Road,

Tunbridge Wells, Kent TN1 2DJ
Tel: +44 (0)1892 518000
Fax: +44 (0)1892 518100
Email: [email protected]

14503 Bammel N, Houston #110,

Houston,Texas, 77014.
Tel: +1 281 583 0583
Fax: +1 281 583 0587
E-mail: [email protected]

These are standard design specifications.

We operate a policy of continuous
development and the information on this
sheet may be updated without notice.

www.jiskoot.com