Addendum

iSeries Instruments
Part Number 104633-00
16Aug2012

About This Addendum

This addendum provides information that describes software updates and
corrections for iSeries manuals.
The addendum is organized as follows:

Universal updates for all iSeries manuals

Updates for selected manuals

Universal Updates for All iSeries

Manuals
Chapter 1 - Introduction

This section describes the updates and corrections that apply to the
Introduction chapter.

Multiple Connects via Ethernet and

NTP Network Time Protocol
Support

In the features list, replace the associated feature with the following:

Analog Output Over/Under Range

Clamping

In the Specifications section, replace the analog outputs description with

the following:

C-Link, MODBUS, Geysitech (Bayern-Hessen), streaming data, and

NTP (Network Time Protocol) protocols. Simultaneous connections
from different locations over Ethernet.

Analog
outputs

6 voltage outputs; 0100 mV, 1, 5, 10 V (user selectable), 5% of full-scale

over/under range (user selectable), 12 bit resolution, measurement output user
selectable per channel

Serial Settings Support

In the Specifications section, replace the analog outputs description with

the following:
Serial
Ports

Chapter 2 - Installation

1 RS-232 or RS-485 with two connectors, baud rate 1200115200, data bits, parity,
and stop bits, protocols: C-Link, MODBUS, Geysitech (Bayern-Hessen), and
streaming data (all user selectable)

This section describes the updates and corrections that apply to the
Installation chapter.
In the Setup section, add the following reference in the step for
connecting a recording device to the rear panel connector:
Instrument Controls > I/O Configuration in the Operation chapter.

Add Device Connection

Information

Connecting External
Devices

If your manual does not include the Connecting External Devices

section, add the following information after the Setup section. Change
the figure and table numbering as appropriate for your manual.
Several components are available for connecting external devices to iSeries
instruments.
These connection options include:

Individual terminal board PCB assemblies

Terminal block and cable kits (optional)

Individual cables (optional)

For detailed information on the optional connection components, refer to

the Optional Equipment chapter. For associated part numbers, refer to
External Device Connection Components in the Servicing chapter.

Terminal Board PCB

Assemblies

The terminal board PCB assembly is a circuit board with a D-Sub

connector on one side and a series of screw terminals on the other. This
assembly provides a convenient mechanism for connecting wires from a
data system to the analyzers I/O connectors.
The following terminal board PCB assemblies are available for iSeries
instruments:

iSeries Manual Update Addendum

I/O terminal board PCB assembly, 37 pin (standard)

D/O terminal board PCB assembly, 37 pin (standard)

25-pin terminal board PCB assembly, (included with optional I/O

Expansion Board)

Thermo Fisher Scientific

I/O Terminal Board

Figure x-x shows the recommended method for attaching the cable to the
terminal board using the included tie-down and spacer. Table x-x identifies
the connector pins and associated signals.
Note Not all of the I/O available in the instrument is brought out on this
terminal board, if more I/O is desired, an alternative means of connection
is required.

See Detail B
See Detail A

Component Side Viewed from Top of Board

Detail A

Detail B

Assembled Connector

Figure x-x. I/O Terminal Board Views

Table x-x. I/O Terminal Board Pin Descriptions

Thermo Fisher Scientific

Pin

Signal Description

Pin

Signal Description

Analog1

13

Power_Fail_NC

Analog ground

14

Power_Fail_COM

Analog2

15

Power_Fail_NO

Analog ground

16

TTL_Input1

Analog3

17

TTL_Input2

Analog ground

18

TTL_Input3

Analog4

19

TTL_Input4

Analog ground

20

Digital ground

iSeries Manual Update Addendum

D/O Terminal Board

Pin

Signal Description

Pin

Signal Description

Analog5

21

TTL_Input5

10

Analog ground

22

TTL_Input6

11

Analog6

23

TTL_Input7

12

Analog ground

24

Digital ground

Figure x-x shows the recommended method for attaching the cable to the
terminal board using the included tie-down and spacer. Table x-x identifies
the connector pins and associated signals.

See Detail A
See Detail B

Component Side Viewed from Top of Board

Detail A

Detail B

Assembled Connector

Figure x-x. D/O Terminal Board Views

Table x-x. D/O Terminal Board Pin Descriptions

iSeries Manual Update Addendum

Pin

Signal Description

Pin

Signal Description

Relay1_ContactA

13

Relay7_ContactA

Relay1_ContactB

14

Relay7_ContactB

Relay2_ContactA

15

Relay8_ContactA

Relay2_ContactB

16

Relay8_ContactB

Relay3_ContactA

17

Relay9_ContactA

Relay3_ContactB

18

Relay9_ContactB

Thermo Fisher Scientific

25-Pin Terminal Board

Pin

Signal Description

Pin

Signal Description

Relay4_ContactA

19

Relay10_ContactA

Relay4_ContactB

20

Relay10_ContactB

Relay5_ContactA

21

Solenoid_Drive_Output1

10

Relay5_ContactB

22

+24V

11

Relay6_ContactA

23

Solenoid_Drive_Output2

12

Relay6_ContactB

24

+24V

The 25-pin terminal board is included with the I/O Expansion Board.

See Detail A
See Detail B

Component Side Viewed from Top of Board

Detail A

Detail B

Assembled Connector

Figure x-x. 25-Pin Terminal Board Views

Table x-x. 25-Pin Terminal Board Pin Descriptions

Thermo Fisher Scientific

Pin

Signal Description

Pin

Signal Description

IOut1

13

Analog_In1

GND_ISO

14

Analog_In2

IOut2

15

Analog_In3

GND_ISO

16

GNDD

iSeries Manual Update Addendum

Chapter 3 - Operation
Power-Up Screen

Pin

Signal Description

Pin

Signal Description

IOut3

17

Analog_In4

GND_ISO

18

Analog_In5

IOut4

19

Analog_In6

GND_ISO

20

GNDD

IOut5

21

Analog_In7

10

GND_ISO

22

Analog_In8

11

IOut6

23

GNDD

12

GND_ISO

24

GNDD

This section describes the updates and corrections that apply to the
Operation chapter.
Replace the Thermo Electron Corporation power-up screen with the
Thermo Scientific power-up screen.

Status Bar In the Run Screen section, add the following that describes the new
status bar icons.
The status bar displays the time, the password (lock) icon, service
(wrench) icon, alarm (bell) icon, and optional zero/span sample solenoid
valve status, if installed.
Note Time is always displayed in 24-hour format.

iSeries Manual Update Addendum

Thermo Fisher Scientific

Status Bar Icons

The password (lock) icon indicates that
no parameter changes can be made from
the front panel.

The alarm (bell) icon indicates

that an alarm is active.

The service (wrench) icon indicates that the

instrument is in the service mode.

(defaults vary by instrument)

Change Status Bar

Alarm to Bell Icon

Degree Symbol

Update Datalogging Settings

Change the Alarm references on the status bar to the bell icon or remove
the reference. The Alarm references have been replaced with status bar
icons described previously in this document.

Screens which show temperature values should include the degree symbol
not just the C for Celsius units. The degree symbol has been added to
all screens that were missing it.
The iSeries instruments include a built-in data logging capability as a
standard feature. The operator is allowed to create two different types of
records, which for historical reasons are named lrecs and srecs. Each record
can contain up to 32 different fields or data items, and records can be
created at user-defined intervals ranging from 1 to 60 minutes.
Record generation is tied to the instruments real-time clock. For example,
if the logging period for srecs is set to 30 minutes, a new srec will be
generated on every hour and every half hour (10:00, 10:30, 11:00 ).
Lrecs and srecs can be interleaved. For example, an srec containing just the
current concentration level could be generated every five minutes while an
lrec containing a full set of diagnostic data could be generated once every
hour.
The analyzers computer system includes three megabytes of flash memory
which is enough to store a full lrec containing 32 data items and a full srec
containing 32 items once each minute for a week (>20,000 total records).
If logging is limited to the minimum content of date, time, concentration

Thermo Fisher Scientific

iSeries Manual Update Addendum

and error flags, the analyzer can store data once each minute for four
months (>190,000 records).
Add Span and BKG
Reset to Default Content

Add Span and BKG to default lrec and output lists.

Replace the Reset to Default Content description, under Datalogging,
with the following:
The Reset to Default Content screen is used to reset all of the datalogging
field items to default values for the selected record type. For more
information, about selecting the content of logged data fields, see Select
Content described previously.

Add Serial Settings Menu

and Support

Add Serial Settings to the Communications Settings menu as follows:

Main Menu > Instrument Controls > Communication Settings.
COMMUNICATION SETTINGS:
>SERIAL SETTINGS
INSTRUMENT ID
COMMUNICATION PROTOCOL
STREAMING DATA CONFIG
TCP/IP SETTINGS
RANGE

AVG

DIAGS ALARM

Add Serial Settings descriptions and menu including Data Bits, Parity, and
Stop Bits.
Note The Baud Rate and RS-232/485 selections were moved from the
Communications Settings menu to the Serial Settings screen.

Serial Settings

iSeries Manual Update Addendum

The Serial Settings menu is used for serial communications control and
configuration. In the Main Menu, choose Instrument Controls >
Communication Settings > Serial Settings.

Thermo Fisher Scientific

SERIAL SETTINGS:
>BAUD RATE
DATA BITS
PARITY
STOP BITS
RS-232/485 SEL
RANGE

Baud Rate

AVG

9600
8
NONE
1
RS-232

DIAGS ALARM

The Baud Rate screen is used to set the RS-232/RS485 interface baud rate.
Baud rates of 1200, 2400, 4800, 9600, 19200, 38400, 57600 and 115200
are available. The analyzers default baud rate is set to 9600 to provide
backwards compatibility with the older C-series analyzers.
BAUD RATE:
CURRENTLY:
SET TO:

9600
19200 ?

CHANGE VALUE
SAVE VALUE

RANGE

Data Bits

AVG

DIAGS ALARM

The Data Bits Screen is used to set the number of serial data bits.
Selections of 7 or 8 are available (defaults to 8).
DATA BITS:
CURRENTLY:
SET TO:

8
7

CHANGE VALUE

SAVE VALUE
RANGE

Parity

Thermo Fisher Scientific

AVG

DIAGS ALARM

The Parity screen is used to select the parity bit for the serial port.
Selections of NONE, EVEN, or ODD are available (defaults to NONE).

iSeries Manual Update Addendum

PARITY:
CURRENTLY:
SET TO:

NONE
NONE

CHANGE VALUE

SAVE VALUE
RANGE

Stop Bits

AVG

DIAGS ALARM

The Stop Bits screen is used to select the number of stop bits for the serial
port. Selections of 1 and 2 are available (defaults to 1).
STOP BITS:
CURRENTLY:
SET TO:

1
2

CHANGE VALUE

SAVE VALUE
RANGE

Replace Equipment
Damage Alert

AVG

DIAGS ALARM

Replace the Equipment Damage alert in the RS-232/RS-485 Selection

section with the following:
Equipment Damage Disconnect the serial cable before changing RS-232
and RS-485 selection to prevent damage to any equipment currently
connected to the analyzer.

Add Network Time

Protocol Server

Add Network Time Protocol Server (NTP SVR) to the TCP/IP Settings
menu as follows:
Main Menu > Instrument Controls > Communication Settings > TCP/IP
Settings.
TCP/IP SETTINGS:
>USE DHCP
OFF
IP ADDR
192.168.1.200
NETMASK
255.255.255.0
GATEWAY
192.168.1.15
HOST NAME
iSeries
NTP SVR
192.168.1.15
RANGE

10

iSeries Manual Update Addendum

AVG

DIAGS ALARM

Thermo Fisher Scientific

Add NTP Server IP Address description and screen:

The Network Time Protocol (NTP) Server screen is used to edit the IP
address of the NTP server. An NTP server may be used to periodically
synchronize the instruments real-time clock with a standard. More
information about the NTP servers and a list of public servers may be
found at http://www.ntp.org.
In the Main Menu, choose Instrument Controls > Communication
Settings > TCP/IP Settings > NTP Server.
NTP SERVER IP ADDRESS:
CURRENT: 192.168.1.20
SET TO: 192.168.001.015
MOVE CURSOR
CHANGE VALUE
SAVE
RANGE

Add Local/Remote to Non

Alarm Status Items Menu

DIAGS ALARM

Main Menu > Instrument Controls > I/O Configuration > Output Relay
Settings > Relay 1-10 > Instrument State > Non-Alarm, add Local/Remote
to the Non Alarm Status Items menu.

List May Vary Based on Instrument

NON ALARM STATUS ITEMS:

>NONE
<-AUTORANGE
LOCAL/REMOTE
SERVICE
UNITS
ZERO MODE
SPAN MODE

RANGE

Add Available I/O Note

AVG

AVG

DIAGS ALARM

In the Digital Input Settings section, under Instrument Controls, add the
following note, if it is not already included:
Note Not all of the I/O available in the instrument is brought out on the
supplied terminal board, if more I/O is desired, an alternative means of
connection is required.

Add Allow Over/Under Range

to Output Channels Menu

Add Allow Over/Under Range to Output Channels Screen and add the
Allow Over/Under Range screen as follows:
Main Menu > Instrument Controls > I/O Configuration > Analog Output
Config.

Thermo Fisher Scientific

iSeries Manual Update Addendum

11

OUTPUT CHANNELS:
>ALLOW OVER/UNDER RANGE
ALL VOLTAGE CHANNELS
ALL CURRENT CHANNELS
VOLTAGE CHANNEL 1
VOLTAGE CHANNEL 2
VOLTAGE CHANNEL 3
VOLTAGE CHANNEL 4
RANGE

Allow Over/Under Range Screen

AVG

DIAGS ALARM

The Allow Over/Under Range screen, in Analog Output Configuration

under I/O Configuration, is used to select whether or not the analog
outputs are allowed to exceed the maximum selected value of 100 mV, 1 V,
5 V, 10 V, or 20 mA or the minimum selected value of 0 V, 0 mA, or 4
mA. By default this parameter is set to on, and 5% over and under range is
allowed for all analog output channels.
In the Main Menu, choose Instrument Controls > I/O Configuration >
Analog Output Config > Allow Over/Under Range.
ALLOW OVER/UNDER RANGE:
CURRENTLY:
OFF
SET TO:
ON

TOGGLE VALUE
RANGE

Update Number of Table

Points Description

AVG

DIAGS ALARM

Replace the Number of Table Points, under Analog Input Configuration

under I/O Configuration, description with the following:
The Number of Table Points screen allows the user to select how many
points are used in the analog input conversion table. The instrument uses
linear interpolation between the points in this table to determine what the
reading value is based on the analog input voltage. Each point in the table
consists of an analog input voltage value (0-10.5 V) and a corresponding
reading value. Only two points are necessary for linear inputs, however a
larger number of points may be used to approximate non-linear inputs.
The points range from 2 to 10, with a default of 2.

Screen Contrast

In the first paragraph, in Screen Contrast under Instrument Controls,

change increments of 10 to increments of 5. Add the following three
notes to the Instrument Controls > Screen Contrast section:
Notes The optimal contrast will change with changes in temperature.

12

iSeries Manual Update Addendum

Thermo Fisher Scientific

The optimal contrast will change from one LCD screen to another. If the
LCD screen is replaced, the contrast may need to be reset.
If the display contrast is not optimal, but the content on the screen is
visible, select Instrument Controls > Screen Contrast and adjust the screen
contrast. If the content on the screen is not visible, use the set contrast 10
C-Link command to set screen contrast to mid range, then optimize the
contrast. See Contrast Levels in the C-Link Protocol Commands
Appendix section of this document for more information on this
command.

Add Timezone Screen

Add Timezone Screen selection to the Instrument Controls menu

INSTRUMENT CONTROLS:
>AUTO/MANUAL MODE
FLASH LAMP
DATALOGGING SETTINGS
COMMUNICATION SETTINGS
I/O CONFIGURATION
TEMPERATURE COMPENSATION
PRESSURE COMPENSATION
RANGE

AVG

DIAGS ALARM

SCREEN CONTRAST
SERVICE MODE
DATE/TIME
TIMEZONE

Add Timezone Screen description and screen display:

The Timezone screen is used to set the timezone for the NTP time server.
This should be set to the timezone that the instrument is located in. If the
exact timezone is not shown in the list, it may be entered via the CLINK
TZ command (see Appendix B). The selections are: UTC (GMT), EST
(GMT+5), CST (GMT+6), MST (GMT+7), PST (GMT+8), YST
(GMT+9), HST (GMT+10), NST (GMT+11), DLW (GMT+12), CET
(GMT-1), EET (GMT-2), BST (GMT-3), DLT (GMT-4), ECH (GMT5), FOX (GMT-6), GLF (GMT-7), CCT (GMT-8), JST (GMT-9), GST
(GMT-10), LMA (GMT-11), DLE (GMT-12), EDT (GMT+5/4), CDT
(GMT+6/5), MDT (GMT+7/6), and PDT (GMT+8/7)
In the Main Menu, choose Instrument Controls > Timezone.

Thermo Fisher Scientific

iSeries Manual Update Addendum

13

TIMEZONE FOR TIMESERVER:

CURRENTLY: UTC (GMT)
SET TO: UTC (GMT)
CHANGE VALUE

SAVE VALUE
RANGE

Digital Inputs

AVG

DIAGS ALARM

Replace the Digital Inputs description, under the Diagnosis menu, with the
following:
The Digital Inputs screen (read only) displays the state of the 16 digital
inputs. Pull-ups are provided on all the inputs, so if nothing is connected
they will read (1), if an input is brought to ground, it will read (0).

Zero and Span Check

Replace the Zero and Span Check description, under the Alarms menu,
with the following:
The Zero and Span Check screen allows the user to view the status of the
most recent zero/span checks and set the maximum check offsets. An alarm
will be triggered if a zero or span check indicates drift that exceeds the
offset value. The zero and span check screens are visible only if the
zero/span check option is enabled. Their functions are similar.

Zero and Span Auto Calibration

Replace the Zero and Span Auto Calibration description, under the Alarms
menu, with the following:
The Zero and Span Auto Calibration screens (read only) allow the user to
view the status of the most recent auto background calibration or span
calibrations. The zero and span auto calibration screens are visible only if
the zero/span check option is enabled and the zero or span cal reset
function is enabled.

Add Wait 30 Seconds Note

Add the following note to all pressure, flow, and temperature sensor
calibration screens in the Service menu.
Note Wait at least 30 seconds for the reading to stabilize before saving the
value.

Lock/Unlock and
Local/Remote Operation

Add the following below Lock Instrument in the Password Menu

section:
If the instrument keyboard is locked via the front panel using Password >
Lock Instrument, the instrument reports being in Remote mode. In this

14

iSeries Manual Update Addendum

Thermo Fisher Scientific

mode, the keypad is locked, data can be viewed but not changed using the
front panel interface, and the remote Set commands are active.
If the instrument keyboard is unlocked via the front panel using Password
> Unlock Instrument, the instrument reports being in Local mode, the
front panel interface is unlocked, and data can be changed from the front
panel.
Refer to the C-Link Protocol Commands appendix for detailed
information about mode, allow mode, and power up mode
commands.
Add Ext Alarms

Add Ext Alarms to the list of Other Measurements in the Datalogging

Settings menu, Streaming Data Configuration menu, Analog Output
Configuration menu, and Digital Inputs screen. Note that Ext Alarms is
displayed in the Alarms menu if it was previously selected in the Digital
Inputs screen.

Change Gas Units to

Lower Case

Change gas units in the screens to lower case.

Change LPM to L/min

Change LPM in the screens to L/min.

Chapter 6 Troubleshooting
Add Cause and Action
Descriptions

Thermo Fisher Scientific

This section describes the updates and corrections that apply to the
Troubleshooting chapter.

In the Troubleshooting - Measurement Failures troubleshooting table,

add the following highlighted Possible Cause and Action descriptions:
Malfunction

Possible Cause

Action

Analog signal
doesnt match
expected value.

Software has not

been configured.

Verify that the selected analog output has been

properly configured to match the data system.

Analog output
goes above fullscale value or
below zero

By default, a 5% over and under range on the

analog outputs is provided. If this is not desirable
due to system restrictions, it may be turned off in
the INSTRUMENT CONTROLS > I/O
CONFIGURATION > ANALOG OUTPUT CONFIG
screens.

iSeries Manual Update Addendum

15

Change Number of Pins on

Board-Level Connection
Diagram

Change Pin 13 Description on

I/O Expansion Board

Add Digital and Analog

Descriptions to Ground
Pins

If not already corrected, in the Board-Level Connection Diagrams

section, change the number of pins on the front panel board to 14 pins for
J2 and 3 pins for J4:

In the I/O Expansion Board Connector Pin Descriptions table, change

the description of pin 13 from NC to Current Output Return.

In the Motherboard Connector Pin Descriptions table add Digital and

Analog descriptions to the 37-pin I/O Connector Label as follows:
Add Digital to pins 2, 5, 13, 22, 26, and 32
Add Analog to pins 16, 18, 19, 35, and 37

Chapter 7 Servicing
Equipment Damage Static Electricity Damage

This section describes the updates and corrections that apply to the
Servicing chapter.

Replace the Equipment Damage precaution statement for static electricity

with the following:

Equipment Damage Some internal components can be damaged by small

amounts of static electricity. A properly ground antistatic wrist strap must
be worn while handling any internal component. If an antistatic wrist strap
is not available, be sure to touch the instrument chassis before touching any
internal components. When the instrument is unplugged, the chassis is not
at earth ground.

Add Device Connection

Information

16

iSeries Manual Update Addendum

If your manual does not include the External Device Connection

Components section, add the following information after Cable List.
Change the table numbering as appropriate for your manual.

Thermo Fisher Scientific

External Device
Connection
Components

Table x-x lists the standard and optional cables and components used for
connecting external devices such as PCs and data loggers to an iSeries
instrument.
Table x-x. External Device Connection Components

Replace Fan
Replacement Procedure

Fan/Filter
Replacement

Part
Number

Description

102562-00

Terminal Block and Cable Kit (DB25) (optional)

102556-00

Terminal Block and Cable Kit (DB37) (optional)

102645-00

Cable, DB37M to Open End Cable, Six Feet (optional)

102646-00

Cable, DB37F to Open End, Six Feet (optional)

102659-00

Cable, DB25M to Open End, Six Feet (optional)

6279

Cable, RS-232 (optional)

102888-00

Terminal Board PCB Assembly, DB37F (standard)

102891-00

Terminal Board PCB Assembly, DB37M (standard)

103084-00

Terminal Board PCB Assembly, DB25M (included with optional I/O Expansion
Board)

Replace the Fan Replacement procedure with the following Fan/Filter

Replacement procedure:

Use the following procedure to replace the rear panel fan and the filter.
Equipment Required:
Fan
Fan filter
Philips screwdriver

Equipment Damage Some internal components can be damaged by small

amounts of static electricity. A properly ground antistatic wrist strap must
be worn while handling any internal component.
1. Turn instrument OFF, unplug the power cord, and remove the cover.

Thermo Fisher Scientific

iSeries Manual Update Addendum

17

2. Remove the fan guard and filter from the rear of the instrument by
unsnapping it.
3. If the fan is not being replaced, install the new filter, snap it into place,
and skip the remaining steps.
4. If possible, disconnect the fan power cable from the fan, otherwise
disconnect the cable from the measurement interface board.
5. Remove the four fan mounting screws along with nuts and washers and
remove the fan.
6. Install a new fan following the previous steps in reverse order.
Correct Pin Designations on
I/O Expansion Connector

In the Analog Output Testing section, correct the I/O Expansion

connector pin designations to the following:

LCD Module Replacement

In the LCD Module Replacement procedure, change Step 4 to the

following:
4. Slide the LCD module out towards the center of the instrument.
Add the following note at the end of the LCD Module Replacement
procedure.
Note The optimal contrast will change from one LCD screen to another.
After replacing the LCD screen, the contrast may need to be reset. If the
content on the screen is visible, select Instrument Controls > Screen
Contrast and adjust the screen contrast. If the content on the screen is not
visible, use the set contrast 10 C-Link command to set screen contrast to
mid range, then optimize the contrast. See the C-Link Protocol
Commands appendix for more information on this command.

18

iSeries Manual Update Addendum

Thermo Fisher Scientific

Chapter 8 System
Description
Add Connection Information

This section describes the updates and corrections that apply to the
System Description chapter.
Add the following to the Ethernet Connection section:
Up to three simultaneous connections are allowed per protocol.

Update Analog Voltage

Inputs Description

Replace the Analog Voltage Inputs (Optional) description with the

following:
Eight analog voltage inputs are used to gather measurement data from
third-party devices. The user may assign a label, unit, and a conversion
table (2 to 10 points). Each point in the conversion table consists of an
analog input voltage value (0-10.5 V) and a corresponding user-defined
reading value. Only two points are necessary for linear inputs, however a
larger number of points may be used to approximate non-linear inputs. All
voltage inputs have a resolution of 12 bits over the range of 0 to 10.5 volts.

Add Over and Under

Range Information

Add the following to the Analog Voltage Outputs and Analog Current
Outputs (Optional) sections.
At least 5% of full-scale over and under range are also supported, but may
be overridden in software if required.

RS-232 Connection

Change the caption of Table 8-1 to: RS-232 DB9 Connector Pin
Configuration.

RS-485 Connection

Change the caption of Table 8-2 to: RS-485 DB9 Connector Pin
Configuration.

Chapter 9 Optional
Equipment

Change the description of the retrofit rack in Table 9-3 to the following:

Add 25-Pin Terminal Board

Assembly Reference

If your manual does not include the 25-Pin Terminal Board Assembly
reference, add the following information after I/O Expansion Board
Assembly.

Thermo Fisher Scientific

This configuration is intended for direct replacement of a C-Series

instrument in an existing rack. The rail mounting location is lower on the
case and the front mounting screw slots are in non-standard EIA locations.

iSeries Manual Update Addendum

19

25-Pin Terminal
Board Assembly

The 25-pin terminal board assembly is included with the I/O expansion
board. Refer Terminal Board PCB Assemblies in the Installation
chapter for information on attaching the cable to the connector board. For
associated part numbers, refer to External Device Connection
Components in the Servicing chapter.

Add Optional Cables

If your manual does not include the Cables reference, add the following
information after I/O Expansion Board Assembly. Change the table
numbering as appropriate for your manual.

Cables

Table x-x identifies the optional individual cables that are available for the
instrument and provides the cable color codes. For associated part
numbers, refer to External Device Connection Components in the
Servicing chapter.
Note Table x-x provides the color coding for both 25-pin cables and 37pin cables. Color codes for pins 1-25 are for 25-pin cables; color codes for
pins 1-37 are for 37-pin cables.
Table x-x. Cable Options
Description

Cable Length

DB37M to open end

Six feet

DB37F to open end

Six feet

DB25M to open end

Six feet

RS-232

Table x-x. Color Codes for 25-Pin and 37-Pin Cables

20

iSeries Manual Update Addendum

Pin

Color

Pin

Color

BLACK

20

RED/BLACK

BROWN

21

ORANGE/BLACK

RED

22

YELLOW/BLACK

ORANGE

23

GREEN/BLACK

YELLOW

24

GRAY/BLACK

GREEN

25

PINK/BLACK

BLUE

End color codes for 25-pin cables

continue for 37-pin cables.

VIOLET

26

PINK/GREEN

Thermo Fisher Scientific

Pin

Color

Pin

Color

GRAY

27

PIND/RED

19

WHITE

28

PINK/VIOLET

11

PINK

29

LIGHT BLUE

12

LIGHT GREEN

30

LIGHT BLUE/BROWN

13

BLACK/WHITE

31

LIGHT BLUE/RED

14

BROWN/WHITE

32

LIGHT BLUE/VIOLET

15

RED/WHITE

33

LIGHT BLUE/BLACK

16

ORANGE/WHITE

34

GRAY/GREEN

17

GREEN/WHITE

35

GRAY/RED

18

BLUE/WHITE

36

GRAY/VIOLET

19

VIOLET/WHITE

37

LIGHT GREEN/BLACK

CLink Protocol
Commands Appendix

This section describes the updates and corrections that apply to the CLink Protocol Commands appendix.

Add Command Response

Descriptions

Add the following new command response table to the C-Link Protocol
Commands appendix under Commands:
Table x-x. Command Response Error Descriptions

Add Connection Information

Command Response

Description

too high

Supplied value is higher than the upper limit

too low

Supplied value is lower than the lower limit

invalid string

Supplied string invalid (typically because a letter was detected

when the value should be numeric)

data not valid

Supplied value is not acceptable for entered command

cant, wrong settings

Command not allowed for current measurement mode

cant, mode in service

Command not allowed while instrument is in service mode

Add the following to the end of the first paragraph and to the Accessing
Streaming Data section:
Up to three simultaneous connections are allowed per protocol.

Thermo Fisher Scientific

iSeries Manual Update Addendum

21

Update Table B-1

Add /sets following Reports in the analog iout range and analog vout
range command descriptions.
Replace the alarm trig conc description with the following:
Reports/sets current concentration alarm trigger sense.

Replace Erec Description

Replace the erec description in the C-Link Protocol Commands table

with the following:
Returns a snapshot of the main operating conditions (measurements and
status) in the specified format.
Replace the erec description in the erec command with the following:
This command returns a snapshot of the main operating conditions
(measurements and status) at the time the command is issued. The example
that follows shows a typical response.
The format is defined by the current settings of the format and erec
format commands. For details on erec formatting, see the Record Layout
Definition section at the end of this appendix. For details on how to
decode the flag fields within these records, see the flags command.

Add Service Mode Section

Convert Concentration Formats

Update Lrec Mem Size

After the Entering Units in PPB section, add the following:

Convert concentration formats from xxxxE+yy to x.xxxE+yy. The iSeries
uses more standard script than the C-Series by placing only one digit to the
left of the decimal.

Replace the lrec mem size description with the following:

These commands report the number of lrecs and srecs that can be stored
with the current settings and the number of blocks reserved for lrecs and
srecs. The example that follows shows that 1075 blocks were reserved for
lrecs and the maximum number of lrecs that can be stored in memory is
241979. Memory allocation can be changed using the malloc command.
Send:
Receive:

22

iSeries Manual Update Addendum

lrec mem size

lrec mem size 241979 recs, 1075 blocks

Thermo Fisher Scientific

Update Set Layout Ack

Replace the set layout ack description with the following and add the table:
This command disables the stale layout/layout change indicator (*) that is
attached to each response if the erec layout has changed since the last time
erec layout was requested.
Table x-x. Set Layout Ack Values

Change Flags Field

Value

Function

Do nothing (default)

Append *

Change the 2-bit flags field that reported Local/Remote/Service to Service

on/off and Password Lock on/off. The most significant bit of the 2-bit
fields is Service Status and the least significant bit is for Password Lock
status.
1= ON
0= OFF

Replace DHCP Descriptions

Replace DHCP associated descriptions with the following:

set dhcp onoff
This command enables (on) and disables (off) the DHCP service. When
DHCP is set to on, the instrument gets the IP address, the netmask
address, and the gateway address from a DHCP server. When DHCP is set
to off, the instrument gets these addresses from system memory.
Note When changing the IP address, the netmask address, or the gateway
address, you must cycle power to the instrument before the change takes
effect. Until you cycle power, the address assigned by the DHCP server will
still be used and reported as the current address.

Add Note to Addr GW, Addr

IP, and Addr NM Commands

Add the following note to the addr gw, addr IP, and addr nm commands:
Note This command cannot be used when DHCP is on. Refer to the
DHCP command that follows for additional information.

Alarm Internal Temp Command

Alarm Pressure Command

Thermo Fisher Scientific

Change alarm internal temp command format from internal alarm temp
to alarm internal temp in the examples and associated set commands.
Change alarm pressure command format from pressure alarm in the
example to alarm pressure.
iSeries Manual Update Addendum

23

Alarm Sample Flow Command If the instrument includes the alarm sample flow command, the response is
formatted to be three digits to the right of the decimal, such as 0.350 lpm
instead of one digit to the right of the decimal.
Clr Records Command Change clear records command format from clear records to clr records
in the example.
Contrast Levels

Screen contrast levels can now be changed in 5% increments instead of

10% increments. Refer to the following Contrast Levels table.
Table x-x. Contrast Levels

Gas Unit Command

24

iSeries Manual Update Addendum

Level

Contrast Level

0%

5%

10%

15%

20%

25%

30%

35%

40%

45%

10

50%

11

55%

12

60%

13

65%

14

70%

15

75%

16

80%

17

85%

18

90%

19

95%

20

100%

Change set gas unit to set gas unit unit.

Thermo Fisher Scientific

Add Scratch Pad Description

Add the following scratch pad description to the list sp, set copy sp to
lrec/srec/stream, set copy lrec/srec/stream to sp, sp field, and set sp field
commands:
The scratch pad is a temporary memory area which is used to set up lists of
selections for lrec, srec, or streaming data items. The user can copy any of
these lists to the scratch pad, modify individual elements in the list, then
save the scratch pad back to the original list. Refer to the sp field
command for information on how to edit the scratch pad.

Add the Allow Mode Command

Add the Allow Mode command to the Commands List section and the
Communications Configuration section as follows:
allow mode cmd

Reports/sets the current set allow mode command

allow mode cmd

This command reports the current allow mode setting: 1 = allow set mode
local or set mode remote commands; 0 = ignore set mode local or set
mode remote commands. The default value is 0; ignore the commands
(refer to the table that follows). The example that follows shows that the
instrument is configured to ignore set mode local or set mode remote
commands.
Send:
Receive:

allow mode cmd

allow mode cmd 0

set allow mode cmd value

This command is used to configure the instrument to value, where value is
either 1 = accept or 0 = ignore the set mode local and set mode remote
commands. Refer to the table that follows.
If the instrument is set to accept the commands (value = 1), the set mode
local command will unlock the instrument and the keypad can be used to
make changes via the front panel.
If the instrument is set to ignore the commands (value = 0), the instrument
will respond with ok as if the command has been accepted and acted
upon, but will not change the instrument lock status (this is for
compatibility with systems expecting an ok response).

Thermo Fisher Scientific

iSeries Manual Update Addendum

25

Note The instrument will always respond to the command mode with
the status of the password lock as mode local or mode remote
regardless of the above setting.
The example that follows sets the instrument to accept the set mode local
or set mode remote commands.
Send:
Receive:

set allow mode cmd 1

set allow mode cmd 1 ok

Table x-x. Allow Mode Command Values

Add the Power Up

Mode Command

Value

Allow Mode Command

Ignore (default)

Accept

Add the Power Up Mode command to the Commands List section and
the Communications Configuration section as follows:
power up mode

Reports/sets the power up mode as local or remote

power up mode
This command reports the current power up mode setting, where value, is
either 0 = local/unlocked or 1 = remote/locked. The default value is 0;
power up in local/unlocked mode. The example that follows shows that the
instrument is configured to power up in the remote/locked mode.
Send:
Receive:

power up mode
power up mode 1

set power up mode value

This command is used to configure the instrument to power up in the
local/unlocked mode (value = 0) or the remote/locked mode (value = 1).
If the instrument is set to power up in the local/unlocked mode, the keypad
can be used to make changes via the front panel. If the instrument is set to
power up in the remote/locked mode, changes can not be made from the
front panel. The example that follows sets the instrument to power up in
remote/locked mode.

26

iSeries Manual Update Addendum

Thermo Fisher Scientific

Send:
Receive:

set power up mode 1

set power up mode 1 ok

Table x-x. Power Up Mode Values

Add the Addr NTP Command

Value

Power Up Mode Command

Local/Unlocked (default)

Remote/Locked Mode

Add the Addr NTP command to the Commands List section and the
Communications Configuration section as follows:
addr ntp

Reports the IP address for the NTP time server

addr ntp
This command reports the IP address for the NTP time server. See
"Network Time Protocol Server in the Communications Settings
section of the Operation chapter for more information.
Send:
Receive:

addr ntp
addr ntp 192.168.1.2

set addr ntp address

This command sets the NTP time server address, where address consists of
four numbers ranging from 0-255 inclusive, separated by ..
Send:
Receive:

Add the TZ Command

set addr ntp 192.168.1.2

set addr ntp 192.168.1.2 ok

Add the tz command to the Commands List section and the

Communications Configuration section as follows:
tz

Reports/sets the tz timezone string for the NTP server

tz
This command reports the tz timezone string for the NTP server. See
Network Time Protocol Server in the Communications Settings
section of the Operation chapter for more information.
Send:
Receive:

Thermo Fisher Scientific

tz
tz EST+5EDT

iSeries Manual Update Addendum

27

set tz string
This command sets the timezone string for the instrument for use with the
NTP time server, where string is a standard timezone string. Common
strings are listed in the timezone screen description in Chapter 3.
Send:
Receive:

Add the Menutext Command

set tz EST+5EDT
set tz EST+5EDT ok

Add the Menutext command to the Commands List section and the
Keys Display section as follows:
menutext

Displays the text of the menu item where the cursor is currently
positioned

menutext
This command displays the text of the menu item where the cursor is
currently positioned. The example that follows shows that the cursor is
positioned at the instrument controls menu item.
Send:
Receive:

Add C-link MODBUS

Related Commands

menutext
menutext

main menu

instrument controls

Add the following C-link MODBUS related commands to the

Commands List section and the I/O Configuration section as follows:
mb read coils start
count

Reports the current state of the MODBUS coils (digital outputs)

mb read registers start

count

Reports the current state of the MODBUS registers (analog outputs)

set mb write coil coil

state

Sets the current state of the MODBUS coil coil (digital input)

mb read coils start count

start = index of first coil, count = number of coils to report.
This command reports the current state of the MODBUS coils (digital
outputs). Output is in binary format with the coil start appearing as the
right-most bit.
Send:
Receive:

28

iSeries Manual Update Addendum

mb read coils 1 15
mb read coils 1 15 000000100000001

Thermo Fisher Scientific

mb read registers start count

start = index of first register (must be odd number), count = number of
registers to report (must be even), each pair of registers is reported as a
float.
This command reports the current state of the MODBUS registers (analog
outputs). Output is in floating point format with the pair of registers start
and start+1 appearing as the left-most value.
Send:
Receive:

mb read registers 5 4
mb read registers 5 4 552629.000000 55998800.000000

set mb write coil coil state

coil = index of coil to be set, state = 1 or 0
This command sets the current state of the MODBUS coil coil (digital
input). coil has an offset of 100 (that is, the first write coil is address 101).
Send:
Receive:

Add Zero and Span Commands

set mb write coil 104 1

set mb write coil 104 1 ok

Add the following zero and span commands to the Commands List
section and to the Calibration section as follows:
span dev

Reports/sets span deviation (maximum span check offset)

zero dev

Reports/sets zero deviation (maximum zero check offset)

span cal reset

Reports/sets span cal reset on/off

span dur

Reports/sets how long span gas is sampled by the instrument

zero cal reset

Reports/sets zero cal reset on/off

zero dur

Reports/sets how long zero gas is sampled by the instrument

zs period

Reports/sets zero/span period

zs avg time

Reports/sets zero/span averaging time

span dev
This command reports the span deviation (span check offset). The example
that follows reports that the span deviation is 1 ppb.
Send:
Receive:

Thermo Fisher Scientific

span dev
span dev 1.000 E+00

iSeries Manual Update Addendum

29

set span dev value

This command sets the span deviation (span check offset) to value, where
value is a floating-point representation of the gas concentration in current
selected units. The example that follows sets the span deviation to 345 ppb.
Send:
Receive:

set span dev 345

set span dev 345 ok

zero dev
This command reports the zero deviation (maximum zero check offset).
The example that follows reports that the zero deviation is 10 ppb.
Send:
Receive:

zero dev
zero dev 1.000 E+01

set zero dev

This command sets the zero deviation (maximum zero check offset) to
value, where value is a floating-point representation of the gas
concentration in current selected units. The example that follows sets the
zero deviation to 10 ppb.
Send:
Receive:

set zero dev 1.000 E+01

set zero dev 1.000 E+01 ok

span cal reset

This command reports that the span cal reset is on or off. The example that
follows reports that the span cal reset is on.
Send:
Receive:

span cal reset

span cal reset on

set span cal reset onoff

This command sets the span cal reset to on or off. The example that
follows sets the span cal reset to off.
Send:
Receive:

set span cal reset off

set span cal reset off ok

zero cal reset

This command reports that the zero cal reset is on or off. The example that
follows reports that the zero cal reset is off.
Send:
Receive:

30

iSeries Manual Update Addendum

zero cal reset

zero cal reset off

Thermo Fisher Scientific

set zero cal reset onoff

This command sets the zero cal reset on or off. The example that follows
turns the zero cal reset off.
Send:
Receive:

set zero cal reset off

set zero cal reset off ok

span dur
This command reports the span duration. The example that follows reports
that the span duration min is 10 minutes.
Send:
Receive:

span dur
span dur 10 min

set span dur value

This command sets span duration to value where value represents the span
duration in minutes. The example that follows sets the span duration to 15
minutes.
Send:
Receive:

set span dur 15

set span dur 15 ok

zero dur
This command reports the zero duration. The example that follows reports
that the zero duration is 10 minutes.
Send:
Receive:

zero dur 10
zero dur 10 ok

set zero dur value

This command sets the zero duration to value where value represents the
zero duration in minutes. The example that follows sets the zero duration
to 15 minutes.
Send:
Receive:

set zero dur 15

set zero dur 15 ok

zs period
This command reports the zero/span (zs) period. The example that follows
reports that the zero/span period is 24 hours.
Send:
Receive:

Thermo Fisher Scientific

zs period
zs period 24 hr

iSeries Manual Update Addendum

31

set zs period value

This command sets zero/span (zs) period to value, where value represents
the zero/span period in hours. The example that follows sets the zero/span
period to 24 hours.
Send:
Receive:

set zs period 24
set zs period 24 hr ok

zs avg time
This command reports the zero/span (zs) averaging time in seconds. The
example that follows reports that the zero/span averaging time is 30
seconds, according to the Averaging Times table in this appendix.
Send:
Receive:

zs avg time
zs avg time 5:30 sec

set zs avg time

This command sets the zero/span averaging time, according to the
Averaging Times table. The example that follows sets the zero/span
averaging time to 120 seconds.
Send:
Receive:

Add the Version Command

set zs avg time 8

set zs avg time 8 ok

Add the Version command to the Commands List section and the
Diagnostics section as follows:
version

Reports version of all the firmware components

version
This command reports the version of all the firmware components. The
example that follows shows a list of firmware components that were
displayed by issuing the version command. The components displayed will
vary depending on the configuration of the instrument.
Send:
Receive:

version
version
Program = 01.05.79.225
Library = 01.01.60.167
Kernel = 2.4.24-uc0-003-Thermo
Board = 81, File = /usr/application.hex
Board App = 11.3.100 Bl 4.0.97
File App = 11.3.100 Bl 4.0.97
Board = 84, File = /usr/application.hex
Board App = 11.3.100 Bl 4.0.97

32

iSeries Manual Update Addendum

Thermo Fisher Scientific

File App = 11.3.100 Bl 4.0.97

Arc Bl = 170711*

MODBUS Protocol
Appendix
Update Serial Communication
Parameters

Add Connection Information

This section describes the updates and corrections that apply to the
MODBUS Protocol appendix.

Update the Serial Communication Parameters section as follows:

Number of Data bits

: 7 or 8

Number of Stop bits

: 1 or 2

Parity

: None, Odd, or Even

Data rate

: 1200 to 115200 Baud (9600 is default)

Add the following to the TCP Communication Parameters section:

Up to three simultaneous connections are supported over Ethernet.

Add Service Mode Note

Add the following note to the (0x05) Force (Write) Single Coil section:
Note This function will not work if the instrument is in service mode.

Add Notes to MODBUS

Commands Supported Section

In the MODBUS Commands Supported section (also shown as the

MODBUS Addresses Supported section in some manuals) add the
following notes to the Tables as indicted:
Table C1 through Table C3 list the MODBUS addresses supported for
the Model xxi.
IMPORTANT NOTE The addresses in the following tables are Protocol
Data Unit (PDU) addresses. Verify the coil number on your MODBUS
master to ensure that it matches the coil number on the instrument.
Note Coil status 1 indicates active state.
Table C1. Read Coils for xxi

Thermo Fisher Scientific

Coil Number

Status

Invalid

(add your instrument specific data)

iSeries Manual Update Addendum

33

Coil Number

Status

(end)

(end)

In addition to the coils listed in the Read Coils table, coils in the Write
Coils table can also be read.
IMPORTANT NOTE The addresses in the following tables are Protocol
Data Unit (PDU) addresses. Verify the register number on your
MODBUS master to ensure that it matches the register number on the
instrument.
Note For additional information on how to read registers and interpret the
data, refer to the (0x03/0x04) Read Holding Registers / Read Input
Registers section in this appendix.
Table C2. Read Registers for xxi
Register Number

Variable

Invalid

1&2

(add your instrument specific data)

(end)

(end)

IMPORTANT NOTE The addresses in the following tables are Protocol

Data Unit (PDU) addresses. Verify the coil number on your MODBUS
master to ensure that it matches the coil number on the instrument.
Note Writing 1 to the coil number shown in the following table will
initiate the action triggered listed in the table. This state must be held for
at least 1 second to ensure the instrument detects the change and triggers
the appropriate action.
Note The coils within each coil group in the following table are mutually
exclusive and will not be triggered if there is a conflict. Before you assert (1)
one coil in a group, make sure the other coils in the group are de-asserted
(0).
Table C3. Write Coils for xxi

34

iSeries Manual Update Addendum

Coil Number

Action Triggered

100

Invalid

101

(add your instrument specific data)

Thermo Fisher Scientific

Coil Number

Action Triggered

(end)

(end)

In addition to the coils listed in the Write Coils table, coils in the Read
Coils table can also be read.
Reading a Write Coil
Replace Tables in the
MODBUS Commands
Supported Section

To read a write coil, issue a read coil command for that coil. For example
to view the state of write coil 101, issue a read coil 101.
In the MODBUS Commands Supported section (also shown as the
MODBUS Addresses Supported section in some manuals) replace the
appropriate Tables in your manual with the following Tables and
associated text:

42i Series
In the following Tables, repeated numbers are used to indicate different
functions based on the instrument used.
Read Registers for 42i

Thermo Fisher Scientific

Register Number

Variable

Used Exclusively In

NONE

1&2

NO

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i Y

3&4

NO2

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i

3&4

DIF

42i Y

5&6

NOx

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i D

5&6

NOy

42i Y

7&8

NH3

17i

9&10

NT

17i

11&12

LOW NO

42i, 42i HL, 42i LS, 42i TL, 17i, 42i Y

13&14

LOW NO2

42i, 42i HL, 42i LS, 42i TL, 17i

13&14

LOW DIF

42i Y

15&16

LOW NOx

42i, 42i HL, 42i LS, 42i TL, 17i, 42i D

15&16

LOW NOy

42i Y

17&18

LO NH3

17i

19&20

LO NT

17i

21&22

HIGH NO

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i Y

23&24

HIGH NO2

42i, 42i HL, 42i LS, 42i TL, 17i

iSeries Manual Update Addendum

35

36

iSeries Manual Update Addendum

Register Number

Variable

Used Exclusively In

23&24

HIGH DIF

42i Y

25&26

HIGH NOx

42i, 42i HL, 42i LS, 42i TL, 17i, 42i D

25&26

HIGH NOy

42i Y

27&28

HI NH3

17i

29&30

HI NT

17i

31&32

RANGE

33&34

RANGE

35&36

INTERNAL
TEMPERATURE

37&38

CHAMBER
TEMPERATURE

39&40

COOLER
TEMPERATURE

41&42

NO2 CONVERTER
TEMP

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i D

43&44

EXT CONV TEMP

17i, 42i Y

45&46

PERM OVEN GAS

Perm Span Option

47&48

PERM OVEN
HEATER

Perm Span Option

49&50

CHAMBER
PRESSURE

51&52

SAMPLE FLOW

53&54

PMT VOLTS

55&56

ANALOG IN 1

I/O Expansion Board Option

57&58

ANALOG IN 2

I/O Expansion Board Option

59&60

ANALOG IN 3

I/O Expansion Board Option

61&62

ANALOG IN 4

I/O Expansion Board Option

63&64

ANALOG IN 5

I/O Expansion Board Option

65&66

ANALOG IN 6

I/O Expansion Board Option

67&68

ANALOG IN 7

I/O Expansion Board Option

69&70

ANALOG IN 8

I/O Expansion Board Option

71&72

OZONATOR FLOW

73&74

PREREACTOR

42i TL, 42i Y

75&76

LO PREREACT

42i TL, 42i Y

77&78

HI PREREACT

42i TL, 42i Y

42i, 42i HL with Bypass Flow Option, 42i LS, 42i

TL, 42i J, 17i, 42i Y, 42i D

Thermo Fisher Scientific

Thermo Fisher Scientific

Register Number

Variable

Used Exclusively In

79&80

NO CORRECTION
CONC

O2 Sensor Option

81&82

NO2 CORRECTION
CONC

O2 Sensor Option

83&84

NOx CORRECTION
CONC

O2 Sensor Option

85&86

NH3 CORRECTION
CONC

O2 Sensor Option

87&88

NT CORRECTION
CONC

O2 Sensor Option

89&90

LOW NO
CORRECTION
CONC

O2 Sensor Option

91&92

LOW NO2
CORRECTION
CONC

O2 Sensor Option

93&94

LOW NOx
CORRECTION
CONC

O2 Sensor Option

95&96

LO NH3
CORRECTION
CONC

O2 Sensor Option

97&98

LO NT
CORRECTION
CONC

O2 Sensor Option

99&100

HIGH NO
CORRECTION
CONC

O2 Sensor Option

101&102

HIGH NO2
CORRECTION
CONC

O2 Sensor Option

103&104

HIGH NOx
CORRECTION
CONC

O2 Sensor Option

105&106

HI NH3
CORRECTION
CONC

O2 Sensor Option

107&108

HI NT
CORRECTION
CONC

O2 Sensor Option

109&110

CAPILLARY TEMP

17i

111&112

O2 %

Internal O2 Sensor Option

iSeries Manual Update Addendum

37

Register Number

Variable

Used Exclusively In

113&114

O2 SENS TEMP

Internal O2 Sensor Option

115&116

NO HOURLY

42i J

117&118

NO2 HOURLY

42i J

119&120

NOX HOURLY

42i J

121&122

EXT ALARMS

Read Coils for 42i

38

iSeries Manual Update Addendum

Coil Number

Status

Used Exclusively In

NONE

AUTORANGE

LOCAL/REMOTE

SERVICE

UNITS

ZERO MODE

Zero/Span Option

SPAN MODE

Zero/Span Option

NO MODE

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i Y

NOx MODE

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i D

NOy MODE

42i Y

Nt MODE

17i

10

PRE MODE

42i TL, 42i Y

11

GEN ALARM

12

NO CONC MAX
ALARM

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i Y

13

NO CONC MIN
ALARM

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i Y

14

NO2 CONC MAX

ALARM

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i

14

DIF CONC MAX

ALARM

42i Y

15

NO2 CONC MIN

ALARM

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i

15

DIF CONC MIN

ALARM

42i Y

16

NOx CONC MAX

ALARM

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i D

Thermo Fisher Scientific

Thermo Fisher Scientific

Coil Number

Status

Used Exclusively In

16

NOy CONC MAX

ALARM

42i Y

17

NOx CONC MIN

ALARM

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i D

17

NOy CONC MIN

ALARM

42i Y

18

NH3 CONC MAX

17i

19

NH3 CONC MIN

17i

20

Nt CONC MAX

17i

21

Nt CONC MIN

17i

22

INT TEMP ALARM

23

CHAMB TEMP
ALARM

24

COOLER TEMP
ALARM

25

NO2 CONVERTER
TEMP ALARM

42i, 42i HL, 42i LS, 42i TL, 42i J, 17i, 42i D

26

EXT CNV TEMP

17i, 42i Y

27

PERM OVEN GAS

TEMP ALARM

Perm Span Option

28

PRESSURE ALARM

29

FLOW ALARM

30

OZONE FLOW
ALARM

31

MOTHERBOARD
STATUS ALARM

32

INTERFACE BD
STATUS ALARM

33

I/O EXP BD STATUS

ALARM

34

AUTORANGE

35

CONC ALARM

36

SAMPLE MODE

37

PURGE MODE

Zero/Span Option

38

EXT CONV STAT

17i, 42i Y

39

ZERO CHECK/CAL
ALARM

Zero/Span Option

42i, 42i HL with Bypass Flow Option, 42i LS, 42i TL,
42i J, 17i, 42i Y, 42i D

I/O Expansion Board Option

iSeries Manual Update Addendum

39

Coil Number

Status

Used Exclusively In

40

SPAN CHECK/CAL
ALARM

Zero/Span Option

41

O2 SENSOR
ALARM

Internal O2 Sensor Option

42

CONC ERROR

42i J

43

NO RANGE 1

42i J

44

NO RANGE 2

42i J

45

NO RANGE 3

42i J

46

NO RANGE 4

42i J

47

NO RANGE 5

42i J

48

NO2 RANGE 1

42i J

49

NO2 RANGE 2

42i J

50

NO2 RANGE 3

42i J

51

NO2 RANGE 4

42i J

52

NO2 RANGE 5

42i J

53

NOx RANGE 1

42i J

54

NOx RANGE 2

42i J

55

NOx RANGE 3

42i J

56

NOx RANGE 4

42i J

57

NOx RANGE 5

42i J

58

CALIBRATION

42i J

59

CAL FAIL ALARM

42i J

60

EXT ALARM 1

62

EXT ALARM 2

63

EXT ALARM 3

Table Write Coils for 42i

40

iSeries Manual Update Addendum

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

100

NONE

101

ZERO MODE

Zero/Span Mode

Zero/Span Option

102

SPAN MODE

Zero/Span Mode

Zero/Span Option

103

NO MODE

Measure Mode

42i, 42i HL, 42i LS, 42i TL, 42i J,

17i, 42i Y

Thermo Fisher Scientific

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

104

NOX MODE

Measure Mode

42i, 42i HL, 42i LS, 42i TL, 42i J,

17i, 42i D

104

NOy MODE

Measure Mode

42i Y

105

Nt MODE

Measure Mode

17i

106

PRE MODE

Measure Mode

42i TL, 42i Y

107

SET BACKGROUND

108

CAL TO LO SPAN

109

AOUTS TO ZERO

Analog Out Test

I/O Expansion Board Option

110

AOUTS TO FS

Analog Out Test

I/O Expansion Board Option

111

CAL TO HI SPAN

112

TELEM TROUBLE

42i J

113

HOURLY AVG RST

42i J

114

ZERO/PURGE CAL

42i J

115

SPAN/PURGE CAL

42i J

116

ZERO/SPAN/PURGE

42i J

117

EXT ALARM 1

118

EXT ALARM 1

119

EXT ALARM 1

120

PURGE MODE

42i J

43i Series
In the following Table, repeated numbers are used to indicate different
functions based on the instrument used.
Read Registers for 43i

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

NONE

1&2

SO2 CONC

43i, 43i J, 43i HL, 43i TLE, 450i without SO2

Scrubber Option

3&4

H2S

450i without SO2 Scrubber Option

5&6

CS

450i without SO2 Scrubber Option

5&6

H2S

450i with SO2 Scrubber Option

7&8

LO SO2 CONC (Dual/Auto

43i, 43i J, 43i HL, 43i TLE, 450i without SO2

iSeries Manual Update Addendum

41

Register
Number

42

iSeries Manual Update Addendum

Variable

Used Exclusively In

Range mode)

Scrubber Option

9&10

LO H2S

450i without SO2 Scrubber Option

11&12

LO CS

450i without SO2 Scrubber Option

11&12

LO H2S

450i with SO2 Scrubber Option

13&14

HI SO2 CONC (Dual/Auto

Range mode)

43i, 43i J, 43i HL, 43i TLE, 450i without SO2

Scrubber Option

15&16

HI H2S

450i without SO2 Scrubber Option

17&18

HI CS

450i without SO2 Scrubber Option

17&18

HI H2S

450i with SO2 Scrubber Option

19&20

RANGE (SO2) (Dual/Auto

Range mode)

21&22

INTERNAL TEMP

23&24

CHAMBER TEMP

25&26

H2S CNV TEMP

450i with Internal Converter

27&28

PERM OVEN GAS

TEMPERATURE

Perm Span Option

29&30

PERM OVEN HEATER

TEMPERATURE

Perm Span Option

31&32

CHAMBER PRESSURE

33&34

SAMPLE FLOW

35&36

PMT VOLTS

37&38

FLASH VOLTS

39&40

FLASH REF

41&42

ANALOG IN 1

I/O Expansion Board Option

43&44

ANALOG IN 2

I/O Expansion Board Option

45&46

ANALOG IN 3

I/O Expansion Board Option

47&48

ANALOG IN 4

I/O Expansion Board Option

49&50

ANALOG IN 5

I/O Expansion Board Option

51&52

ANALOG IN 6

I/O Expansion Board Option

53&54

ANALOG IN 7

I/O Expansion Board Option

55&56

ANALOG IN 8

I/O Expansion Board Option

57&58

SO2 HOURLY

43i J

59&60

H2S HOURLY

43i J

61&62

CS HOURLY

43i J

63&64

EXT ALARMS

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

65&66

O2 %

Internal O2 Sensor Option

67&68

O2 SENS TEMP

Internal O2 Sensor Option

69&70

H2S SCRUB

450i with SO2 Scrubber Option

71&72

LO H2S SCRUB

450i with SO2 Scrubber Option

73&74

HI H2S SCRUB

450i with SO2 Scrubber Option

75&76

SO2 COR

Internal O2 Sensor Option

77&78

LO SO2 COR

Internal O2 Sensor Option

79&80

HI SO2 COR

Internal O2 Sensor Option

Read Coils for 43i

Thermo Fisher Scientific

Coil
Number

Status

Used Exclusively In

NONE

AUTORANGE

LOCAL/REMOTE

SERVICE

UNITS (0 = ppm or ppb; 1 =

mg/m3 or g/m3)

ZERO MODE

Zero/Span Option

SPAN MODE

Zero/Span Option

SAMPLE MODE

SO2 MODE

43i, 43i J, 43i HL, 43i TLE, 450i without SO2

Scrubber Option

CS MODE

450i without SO2 Scrubber Option

10

GEN ALARM

11

SO2 CONC MAX ALARM

43i, 43i J, 43i HL, 43i TLE, 450i without SO2

Scrubber Option

12

SO2 CONC MIN ALARM

43i, 43i J, 43i HL, 43i TLE, 450i without SO2

Scrubber Option

13

H2S CONC MAX

450i without SO2 Scrubber Option

14

H2S CONC MIN

450i without SO2 Scrubber Option

15

CS CONC MAX

450i without SO2 Scrubber Option

16

CS CONC MIN

450i without SO2 Scrubber Option

17

INTERNAL TEMP ALARM

iSeries Manual Update Addendum

43

44

iSeries Manual Update Addendum

Coil
Number

Status

Used Exclusively In

18

CHAMB TEMP ALARM

19

CONVERTER TEMP

450i with Internal Converter

20

PERM GAS TEMP

Perm Span Option

21

PRESSURE ALARM

22

SAMPLE FLOW ALARM

23

FLASH REF ALARM

24

FLASH VOLTAGE ALARM

25

MOTHERBOARD STATUS
ALARM

26

MEASUREMENT INTERFACE
BOARD STATUS ALARM

27

I/O EXP BD STATUS ALARM

28

CONC ALARM

29

PURGE MODE

Zero/Span Option

30

ZERO CHK/CAL ALARM

(Zero/Span Option)

Zero/Span Option

31

SPAN CHK/CAL ALARM

(Zero/Span Option)

Zero/Span Option

32

SPAN 1 MODE

Dual Span Option

33

SPAN 2 MODE

Dual Span Option

34

CONC ERROR

43i J

35

SO2 RANGE 1

43i J

36

SO2 RANGE 2

43i J

37

SO2 RANGE 3

43i J

38

SO2 RANGE 4

43i J

39

SO2 RANGE 5

43i J

40

CALIBRATION

43i J

41

CAL FAIL ALARM

43i J

42

EXT ALARM 1

43

EXT ALARM 2

44

EXT ALARM 3

I/O Expansion Board Option

Thermo Fisher Scientific

Write Coils for 43i

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

100

NONE

101

ZERO MODE

Zero/Span Mode

Zero/Span Option

102

SPAN MODE

Zero/Span Mode

Zero/Span Option

103

SO2 MODE

Measure Mode

43i, 43i J, 43i HL, 43i TLE, 450i without

SO2 Scrubber Option

104

CS MODE

Measure Mode

450i without SO2 Scrubber Option

105

SET BACKGROUND

106

CAL TO LOW SPAN

107

AOUTS TO ZERO

Analog Out Test

I/O Expansion Board Option

108

AOUTS TO FS

Analog Out Test

I/O Expansion Board Option

109

CAL TO HIGH SPAN

110

SPAN 1 MODE

Zero/Span Mode

Dual Span Option

111

SPAN 2 MODE

Zero/Span Mode

Dual Span Option

112

TELEM TROUBLE

43i J

113

HOURLY AVG RST

43i J

114

ZERO/PURGE CAL

43i J

115

SPAN/PURGE CAL

43i J

116

ZERO/SPAN/PURGE

43i J

117

EXT ALARM 1

118

EXT ALARM 2

119

EXT ALARM 3

120

PURGE MODE

Zero/Span Mode

43i J

48i Series
Read Registers for 48i

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

NONE

1&2

CO

48i, 48i TLE, 48i HL

3&4

LO CO

48i, 48i TLE, 48i HL

5&6

HI CO

48i, 48i TLE, 48i HL

7&8

RANGE STATUS

iSeries Manual Update Addendum

45

46

iSeries Manual Update Addendum

Register
Number

Variable

Used Exclusively In

9&10

S/R

11&12

LO S/R

13&14

HI S/R

15&16

INT TEMP

17&18

BENCH TEMP

19&20

NONE

21&22

PERM OVN GAS

Permeation Span Source Option

23&24

PERM OVN HTR

Permeation Span Source Option

25&26

BENCH PRES

27&28

SAMPLE FLOW

29&30

INTENSITY

31&32

MOTOR SPEED

33&34

ANALOG IN 1

I/O Expansion Board Option

35&36

ANALOG IN 2

I/O Expansion Board Option

37&38

ANALOG IN 3

I/O Expansion Board Option

39&40

ANALOG IN 4

I/O Expansion Board Option

41&42

ANALOG IN 5

I/O Expansion Board Option

43&44

ANALOG IN 6

I/O Expansion Board Option

45&46

ANALOG IN 7

I/O Expansion Board Option

47&48

ANALOG IN 8

I/O Expansion Board Option

49&50

CO2

410i

51&52

LO CO2

410i

53&54

HI CO2

410i

55&56

BIAS SUPPLY

57&58

HCl

15i

59&60

LO HCl

15i

61&62

HI HCl

15i

63&64

SCRUBBER EFF

Zero Air Scrubber Option

65&66

LO CO HOURLY

48i J

67&68

EXT ALARMS

69&70

O2 %

Internal O2 Sensor Option

71&72

O2 SENS TEMP

Internal O2 Sensor Option

73&74

N2O

46i

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

75&76

LO N2O

46i

77&78

HI N2O

46i

79&80

CO COR

48i, 48i HL with Internal O2 Sensor Option

81&82

LO CO COR

48i, 48i HL with Internal O2 Sensor Option

83&84

HI CO COR

48i, 48i HL with Internal O2 Sensor Option

85&86

CO2 COR

410i with Internal O2 Sensor Option

87&88

LO CO2 COR

410i Internal O2 Sensor Option

89&90

HI CO2 COR

410i Internal O2 Sensor Option

Read Coils for 48i

Thermo Fisher Scientific

Coil
Number

Status

Used Exclusively In

NONE

AUTORANGE

LOCAL/REMOTE

SERVICE

UNITS

ZERO MODE

Zero/Span Option

SPAN MODE

Zero/Span Option

SAMPLE MODE

GEN ALARM

CONC MAX

10

CONC MIN

11

INT TEMP

12

BENCH TEMP

13

PRESSURE

14

SAMPLE FLOW

15

INTENSITY

16

MOTOR SPEED

17

BIAS VOLTAGE

18

MB STATUS

19

MIB STATUS

20

I/O BD STATUS

I/O Expansion Board Option

iSeries Manual Update Addendum

47

Coil
Number

Status

Used Exclusively In

21

CONC ALARM

22

PURGE MODE

Zero/Span Option

23

SCRUB TST
MODE

Zero Air Scrubber Option

24

ZERO CHK/CAL
ALARM

Zero/Span Option

25

SPAN CHK/CAL
ALARM

Zero/Span Option

26

CONC ERROR

48i J

27

CO RANGE 1

48i J

28

CO RANGE 2

48i J

29

CO RANGE 3

48i J

30

CO RANGE 4

48i J

31

CO RANGE 5

48i J

32

CALIBRATION

48i J

33

CAL FAIL ALARM

48i J

34

EXT ALARM 1

35

EXT ALARM 2

36

EXT ALARM 3

Write Coils for 48i

48

iSeries Manual Update Addendum

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

100

NONE

101

ZERO MODE

Zero/Span Mode

Zero/Span Option

102

SPAN MODE

Zero/Span Mode

Zero/Span Option

103

SET BACKGROUND

104

CAL TO LO SPAN

105

AOUTS TO ZERO

Analog Out Test

I/O Expansion Board

Option

106

AOUTS TO FS

Analog Out Test

I/O Expansion Board

Option

107

CAL TO HI SPAN

108

SCRUBBER TEST

Zero Air Scrubber

Option

Thermo Fisher Scientific

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

109

TELEM TROUBLE

48i J

110

HOURLY AVG RST

48i J

111

ZERO/PURGE CAL

48i J

112

SPAN/PURGE CAL

48i J

113

ZERO/SPAN/PURGE

48i J

114

EXT ALARM 1

115

EXT ALARM 2

116

EXT ALARM 3

117

PURGE MODE

48i J

49i and 49i PS

Read Registers for 49i

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

NONE

1&2

O3

49i

3&4

LO O3

49i

5&6

HI O3

49i

7&8

RANGE STATUS

9&10

INTENSITY A

11&12

INTENSITY B

13&14

NOISE A

15&16

NOISE B

17&18

FLOW A

19&20

FLOW B

21&22

PRESSURE

23&24

BENCH TEMP

25&26

LAMP TEMP

27&28

O3 LAMP TEMP

49i PS, Internal Ozonator Option

29&30

ANALOG IN 1

I/O Expansion Board Option

31&32

ANALOG IN 2

I/O Expansion Board Option

33&34

ANALOG IN 3

I/O Expansion Board Option

iSeries Manual Update Addendum

49

Register
Number

Variable

Used Exclusively In

35&36

ANALOG IN 4

I/O Expansion Board Option

37&38

ANALOG IN 5

I/O Expansion Board Option

39&40

ANALOG IN 6

I/O Expansion Board Option

41&42

ANALOG IN 7

I/O Expansion Board Option

43&44

ANALOG IN 8

I/O Expansion Board Option

45&46

O3 OUT CONC

49i PS

47&48

O3 HOURLY

49i J

49&50

EXT ALARMS

Read Coils for 49i

Coil
Number

50

iSeries Manual Update Addendum

Status

Used Exclusively In

NONE

AUTORANGE

SERVICE

UNITS

ZERO MODE

Sample/Cal Option

SPAN MODE

Sample/Cal Option

SAMPLE MODE

O3 LEVEL 1

O3 LEVEL 2

O3 LEVEL 3

10

O3 LEVEL 4

11

O3 LEVEL 5

12

PURGE MODE

13

GEN ALARM

14

CONC MAX

15

CONC MIN

16

BENCH TEMP

17

BNCH LMP TEM

18

O3 LAMP TEMP

19

PRESSURE

20

FLOW A

Sample/Cal Option

49i PS, Internal Ozonator Option

Thermo Fisher Scientific

Coil
Number

Status

Used Exclusively In

21

FLOW B

22

INTENSITY A

23

INTENSITY B

24

CONC ALARM

25

ZERO CHK/CAL

Sample/Cal Option

26

SPAN CHK/CAL

Sample/Cal Option

27

O3 LEVEL 1 CHK

28

O3 LEVEL 2CHK

29

O3 LEVEL 3 CHK

30

O3 LEVEL 4CHK

31

O3 LEVEL 5 CHK

32

MB STATUS

33

MIB STATUS

34

I/O BD STATUS

35

LOCAL/REMOTE

36

CONC ERROR

49i J

37

O3 RANGE 1

49i J

38

O3 RANGE 2

49i J

39

O3 RANGE 3

49i J

40

O3 RANGE 4

49i J

41

O3 RANGE 5

49i J

42

CALIBRATION

49i J

43

CAL FAIL ALARM

49i J

44

EXT ALARM 1

45

EXT ALARM 2

46

EXT ALARM 3

I/O Expansion Board Option

Write Coils for 49i

Thermo Fisher Scientific

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

100

NONE

101

ZERO MODE

Zero/Span Mode

Sample/Cal Option

102

SPAN MODE

Zero/Span Mode

Sample/Cal Option

iSeries Manual Update Addendum

51

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

103

OZONATOR LVL 1

104

OZONATOR LVL 2

105

OZONATOR LVL 3

106

OZONATOR LVL 4

107

OZONATOR LVL 5

108

SET BACKGROUND

109

CAL TO LO SPAN

110

CAL TO HI SPAN

111

OZONATOR SLND

112

AOUTS TO ZERO

Analog Out Test

I/O Expansion Board Option

113

AOUTS TO FS

Analog Out Test

I/O Expansion Board Option

114

PUMP OFF

115

TELEM TROUBLE

49i J

116

HOURLY AVG RST

49i J

117

ZERO/PURGE CAL

49i J

118

SPAN/PURGE CAL

49i J

119

ZERO/SPAN/PURGE

49i J

120

EXT ALARM 1

121

EXT ALARM 2

122

EXT ALARM 3

123

PURGE MODE

49i PS, Internal Ozonator Option

49i J

51i
Read Registers for 51i

52

iSeries Manual Update Addendum

Register
Number

Variable

NONE

1&2

THC

3&4

AVG THC

5&6

HI THC

7&8

LO THC

9&10

DET TEMP

Used Exclusively In

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

11&12

FILTER TEMP

13&14

PUMP TEMP

15&16

FLAME TEMP

17&18

INT TEMP

19&20

AIR PRESSURE

21&22

SAMPLE PRESSURE

23&24

FUEL PRESSURE

25&26

RAW FID SIGNAL

27&28

ANALOG IN 1

I/O Expansion Board Option

29&30

ANALOG IN 2

I/O Expansion Board Option

31&32

ANALOG IN 3

I/O Expansion Board Option

33&34

ANALOG IN 4

I/O Expansion Board Option

35&36

ANALOG IN 5

I/O Expansion Board Option

37&38

ANALOG IN 6

I/O Expansion Board Option

39&40

ANALOG IN 7

I/O Expansion Board Option

41&42

ANALOG IN 8

I/O Expansion Board Option

43&44

EXT ALARMS

Read Coils for 51i

Thermo Fisher Scientific

Coil
Number

Status

Used Exclusively In

NONE

LOCAL/REMOTE

SERVICE

ZERO MODE

Zero/Span Option

SPAN MODE

Zero/Span Option

SAMPLE MODE

PURGE MODE

IDLE MODE

GEN ALARM

CONC ALARM

10

CONC MAX

11

CONC MIN

Zero/Span Option

iSeries Manual Update Addendum

53

Coil
Number

Status

Used Exclusively In

12

INT TEMP
ALARM

13

DET TEMP
ALARM

14

FILT TEMP
ALARM

15

PUMP TEMP
ALARM

16

AIR PRESSURE
ALARM

17

SAMP
PRESSURE
ALARM

18

FUEL PRESSURE
ALARM

19

FLAME OUT

20

SIGNAL STR

21

OVER RANGE

22

HEATER FAIL

23

SENSOR FAIL

24

ZERO NOISE
ALARM

25

ZERO CHK/CAL

Zero/Span Option

26

SPAN CHK/CAL

Zero/Span Option

27

BIAS VOLTAGE

28

MB STATUS

29

MIB STATUS

30

I/O BD STATUS

31

EXT ALARM 1

32

EXT ALARM 2

33

EXT ALARM 3

I/O Expansion Board Option

Write Coils for 51i

54

iSeries Manual Update Addendum

Coil
Number

Action Triggered

100

NONE

Coil Group

Used Exclusively In

Thermo Fisher Scientific

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

101

ZERO MODE

Zero/Span Mode

Zero/Span Option

102

SPAN MODE

Zero/Span Mode

Zero/Span Option

103

SET BACKGROUND

104

SET IDLE MODE

105

CAL TO SPAN

106

AOUTS TO ZERO

Analog Out Test

I/O Expansion Board

Option

107

AOUTS TO FS

Analog Out Test

I/O Expansion Board

Option

108

EXT ALARM 1

109

EXT ALARM 2

110

EXT ALARM 3

55i
Read Registers for 55i

Thermo Fisher Scientific

Register
Number

Variable

NONE

1&2

LOCAL/REMOTE

3&4

SERVICE

5&6

CAL MODE

7&8

CAL CHK MODE

9&10

RUN MODE

11&12

IDLE MODE

13&14

INJECT

15&16

ZERO MODE

17&18

SPAN MODE

19&20

GEN ALARM

21&22

CH4 CONC MAX

23&24

CH4 CONC MIN

25&26

NM CONC MAX

27&28

NM CONC MIN

29&30

INT TEMP

Used Exclusively In

iSeries Manual Update Addendum

55

Register
Number

Variable

31&32

DET TEMP

33&34

FILT TEMP

35&36

COLUMN TEMP

37&38

AIR PRESSURE

39&40

CARRIER
PRESSURE

41&42

FUEL PRESSURE

43&44

FLAME OUT

45&46

CH4 OVERRANGE

47&48

NM OVERRANGE

49&50

CAL FAILURE

51&52

HEATER FAIL

53&54

SENSOR FAIL

55&56

BIAS VOLTAGE

57&58

DATA INTEG

59&60

CH4 SPAN CHK

61&62

NM SPAN CHK

63&64

WINDOWS SANE

65&66

MB STATUS

67&68

MIB STATUS

69&70

I/O BD STATUS

71&72

EXT ALARM 1

73&74

EXT ALARM 2

75&76

EXT ALARM 3

Used Exclusively In

I/O Expansion Board Option

Read Coils for 55i

56

iSeries Manual Update Addendum

Coil
Number

Status

NONE

LOCAL/REMOTE

SERVICE

CAL MODE

CAL CHK MODE

Used Exclusively In

Thermo Fisher Scientific

Thermo Fisher Scientific

Coil
Number

Status

RUN MODE

IDLE MODE

INJECT

ZERO MODE

SPAN MODE

10

GEN ALARM

11

CH4 CONC MAX

12

CH4 CONC MIN

13

NM CONC MAX

14

NM CONC MIN

15

INT TEMP
ALARM

16

DET TEMP
ALARM

17

FILT TEMP
ALARM

18

COLUMN TEMP

19

AIR PRESSURE

20

CARRIER
PRESSURE

21

FUEL PRESSURE

22

FLAME OUT

23

CH4
OVERRANGE

24

NM
OVERRANGE

25

CAL FAILURE

26

HEATER FAIL

27

SENSOR FAIL

28

BIAS VOLTAGE

29

DATA INTEG

30

CH4 SPAN CHK

31

NM SPAN CHK

32

WINDOWS
SANE

Used Exclusively In

iSeries Manual Update Addendum

57

Coil
Number

Status

33

MB STATUS

34

MIB STATUS

35

I/O BD STATUS

36

EXT ALARM 1

37

EXT ALARM 2

38

EXT ALARM 3

Used Exclusively In

I/O Expansion Board Option

Write Coils for 55i

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

100

NONE

101

START RUN

102

START CAL

103

START CAL CHK

104

STOP

105

INJECT

106

BACKFLUSH

107

SET IDLE MODE

108

AOUTS TO ZERO

Analog Out Test

I/O Expansion Board Option

109

AOUTS TO FS

Analog Out Test

I/O Expansion Board Option

110

EXT ALARM 1

111

EXT ALARM 2

112

EXT ALARM 3

80i
Read Registers for 80i

58

iSeries Manual Update Addendum

Register
Number

Variable

NONE

1&2

Hg0

3&4

Hg2+

5&6

Hgt

Used Exclusively In

Thermo Fisher Scientific

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

7&8

Hg0 RANGE

9&10

Hg2+ RANGE

11&12

Hgt RANGE

13&14

INTENSITY

15&16

INTERNAL TEMPERATURE

17&18

CHAMBER TEMPERATURE

19&20

PROBE TEMPERATURE

21&22

CONVERTER TEMPERATURE

23&24

UMBILICAL TEMPERATURE

25&26

VENTURI PRESSURE

27&28

ORIFICE PRESSURE

29&30

DILUTION AIR PRESSURE

31&32

BLOWBACK PRESSURE

33&34

EDUCTOR PRESSURE

35&36

VACUUM PRESSURE

37&38

FLOW

39&40

PMT VOLTS

41&42

CHAMBER PRESSURE

43&44

PROBE SPAN

45&46

Hg0 SPAN

47&48

Hgt SPAN

49&50

Hg0 BACKGROUND

51&52

Hgt BACKGROUND

53&54

Hg0 COEFFICIENT

55&56

Hgt COEFFICIENT

57&58

PROBE FAILSAFE
TEMPERATURE

59&60

DILUTION FACTOR

61&62

ANALOG IN 1

I/O Expansion Board Option

63&64

ANALOG IN 2

I/O Expansion Board Option

65&66

ANALOG IN 3

I/O Expansion Board Option

67&68

ANALOG IN 4

I/O Expansion Board Option

69&70

ANALOG IN 5

I/O Expansion Board Option

iSeries Manual Update Addendum

59

Register
Number

Variable

Used Exclusively In

71&72

ANALOG IN 6

I/O Expansion Board Option

73&74

ANALOG IN 7

I/O Expansion Board Option

75&76

ANALOG IN 8

I/O Expansion Board Option

77&78

PROBE NUMBER

79&80

Hg0 INSTRUMENT DRIFT

CONCENTRATION

81&82

Hg0 INSTRUMENT DRIFT

TIME

83&84

Hgt INSTRUMENT DRIFT

CONCENTRATION

85&86

Hgt INSTRUMENT DRIFT

TIME

87&88

Hg0 SYSTEM DRIFT

CONCENTRATION

89&90

Hg0 SYSTEM DRIFT TIME

91&92

Hgt SYSTEM DRIFT

CONCENTRATION

93&94

Hgt SYSTEM DRIFT TIME

95&96

CALIBRATOR ACTUAL
CONCENTRATION

97&98

LAMP TEMPERATURE

99&100

OXIDIZER TEMPERATURE

101&102

OXIDATION

103&104

INTEGRITY

105&106

UMB TEMP 2

107&108

EXT ALARMS

Read Coils for 80i

60

iSeries Manual Update Addendum

Coil
Number

Status

NONE

SERVICE

Hg0 MODE

Hgt MODE

Hg0/Hgt MODE

Used Exclusively In

Thermo Fisher Scientific

Thermo Fisher Scientific

Coil
Number

Status

SAMPLE MODE

INSTRUMENT ZERO MODE

INSTRUMENT SPAN MODE

ORIFICE ZERO MODE

ORIFICE SPAN MODE

10

SYSTEM ZERO MODE

11

SYSTEM SPAN MODE

12

BLOWBACK MODE

13

GENERAL ALARM

14

INTERNAL TEMPERATURE
ALARM

15

CHAMBER TEMPERATURE
ALARM

16

CHAMBER PRESSURE
ALARM

17

SAMPLE FLOW ALARM

18

INTENSITY ALARM

19

Hg0 CONCENTRATION,
MAXIMUM ALARM

20

Hg0 CONCENTRATION,
MINIMUM ALARM

21

Hg2+ CONCENTRATION,
MAXIMUM ALARM

22

Hg2+ CONCENTRATION,
MINIMUM ALARM

23

Hgt CONCENTRATION,
MAXIMUM ALARM

24

Hgt CONCENTRATION,
MINIMUM ALARM

25

MOTHERBOARD STATUS
ALARM

26

MEASUREMENT
INTERFACE BOARD STATUS
ALARM

27

I/O BOARD STATUS ALARM

28

CALIBRATOR STATUS

29

ZERO CHECK/CAL ALARM

Used Exclusively In

I/O Expansion Board Option

iSeries Manual Update Addendum

61

Coil
Number

Status

30

SPAN CHECK/CAL ALARM

31

PROBE DILUTION ALARM

32

SYSTEM DILUTION ALARM

33

PROBE ZERO CHECK/CAL

ALARM

34

SYSTEM ZERO CHECK/CAL

ALARM

35

GENERAL PROBE ALARM

36

PROBE 1 SELECTED

37

PROBE 2 SELECTED

38

PROBE 3 SELECTED

39

PROBE 4 SELECTED

40

LOCAL/REMOTE

41

OXIDIZER CAL MODE

42

HYDRATOR

43

PROBE 1 STATUS

44

PROBE 2 STATUS

45

PROBE 3 STATUS

46

PROBE 4 STATUS

47

EXT ALARM

48

SPIKING MODE

Used Exclusively In

Write Coils for 80i

62

iSeries Manual Update Addendum

Coil
Number

Action Triggered

Coil Group

100

NONE

101

Hg0 MODE

Measure Mode

102

Hgt MODE

Measure Mode

103

Hg0/Hgt MODE

Measure Mode

104

INSTRUMENT ZERO MODE

Zero/Span Mode

105

INSTRUMENT SPAN MODE

Zero/Span Mode

106

ORIFICE ZERO MODE

Zero/Span Mode

107

ORIFICE SPAN MODE

Zero/Span Mode

Used Exclusively In

Thermo Fisher Scientific

Coil
Number

Action Triggered

Coil Group

Used Exclusively In

108

SYSTEM ZERO MODE

Zero/Span Mode

109

SYSTEM SPAN MODE

Zero/Span Mode

110

BLOWBACK SYSTEM MODE

Zero/Span Mode

111

BLOWBACK STINGER MODE

Zero/Span Mode

112

SET BACKGROUND

113

CAL INSTRUMENT SPAN

114

PROBE SELECT 1

Probe Select

Hydra Model

115

PROBE SELECT 2

Probe Select

Hydra Model

116

PROBE SELECT 3

Probe Select

Hydra Model

117

PROBE SELECT 4

Probe Select

Hydra Model

118

SYSTEM SPAN 1

System Span

119

SYSTEM SPAN 2

System Span

120

SYSTEM SPAN 3

System Span

121

SYSTEM SPAN 4

System Span

122

SYSTEM SPAN 5

System Span

123

SYSTEM SPAN 6

System Span

124

OXIDIZER CAL MODE

Zero/Span Mode

125

SPIKING

126

INSTRUMENT SPAN 1

Instrument Span

127

INSTRUMENT SPAN 2

Instrument Span

128

INSTRUMENT SPAN 3

Instrument Span

129

HYDRATOR ALARM

130

EXT ALARM

81i
Read Registers for 81i

Thermo Fisher Scientific

Register
Number

Variable

1&2

Hg CONCENTRATION

3&4

Hg SPAN

5&6

Hg FLOW

7&8

DILUTION FLOW

Used Exclusively In

iSeries Manual Update Addendum

63

Register
Number

Variable

Used Exclusively In

9&10

COOLER TEMPERATURE

11&12

AMBIENT TEMPERATURE

13&14

PRESSURE

15&16

COOLER SET TEMPERATURE

17&18

ANALOG IN 1

I/O Expansion Board Option

19&20

ANALOG IN 2

I/O Expansion Board Option

21&22

ANALOG IN 3

I/O Expansion Board Option

23&24

ANALOG IN 4

I/O Expansion Board Option

25&26

ANALOG IN 5

I/O Expansion Board Option

27&28

ANALOG IN 6

I/O Expansion Board Option

29&30

ANALOG IN 7

I/O Expansion Board Option

31&32

ANALOG IN 8

I/O Expansion Board Option

33&34

EXT ALARMS

35&36

Hg RANGE

Read Coils for 81i

64

iSeries Manual Update Addendum

Coil
Number

Status

SERVICE

HG SPAN BIT 1

HG SPAN BIT 2

HG SPAN BIT 3

GENERAL ALARM

STANDBY MODE

INSTRUMENT ZERO MODE

INSTRUMENT SPAN MODE

ORIFICE ZERO MODE

10

ORIFICE SPAN MODE

11

SYSTEM ZERO MODE

12

SYSTEM SPAN MODE

13

COOLER TEMPERATURE
ALARM

14

AMBIENT TEMPERATURE

Used Exclusively In

Thermo Fisher Scientific

Coil
Number

Status

Used Exclusively In

ALARM
15

PRESSURE ALARM

16

Hg FLOW ALARM

17

DILUTION FLOW ALARM

18

CONCENTRATION ALARM

19

MOTHERBOARD STATUS
ALARM

20

MEASUREMENT
INTERFACE BOARD STATUS
ALARM

21

I/O BOARD STATUS ALARM

22

LOCAL/REMOTE

23

EXT ALARM 1

24

EXT ALARM 2

25

EXT ALARM 3

I/O Expansion Board Option

Write Coils for 81i

Thermo Fisher Scientific

Coil
Number

Action Triggered

Coil Group

100

NONE

101

INSTRUMENT ZERO
MODE

Zero/Span Mode

102

INSTRUMENT CAL MODE

Zero/Span Mode

103

ORIFICE ZERO MODE

Zero/Span Mode

104

ORIFICE CAL MODE

Zero/Span Mode

105

SYSTEM ZERO MODE

Zero/Span Mode

106

SYSTEM CAL MODE

Zero/Span Mode

107

STANDBY

108

AOUTS TO ZERO

Analog Out Test

109

HG SPAN BIT 1

Span Level

110

HG SPAN BIT 2

Span Level

111

HG SPAN BIT 3

Span Level

112

AOUTS TO FS

Analog Out Test

Used Exclusively In

I/O Expansion Board

Option

I/O Expansion Board

Option

iSeries Manual Update Addendum

65

Coil
Number

Action Triggered

113

EXT ALARM 1

114

EXT ALARM 2

115

EXT ALARM 3

Coil Group

Used Exclusively In

146i
Read Registers for 146i

66

iSeries Manual Update Addendum

Register
Number

Variable

Used Exclusively In

NONE

1&2

GAS CONC

3&4

TARGET GFLOW

5&6

ACTUAL GFLOW

7&8

TARGET ZFLOW

9&10

ACTUAL ZFLOW

11&12

TARGET TFLOW

13&14

ACTUAL TFLOW

15&16

O3 CONC

Photometer Option

17&18

PERM CONC

Permeation Span Source Option

19&20

PRESSURE

Photometer Option

21&22

BENCH TEMP

Photometer Option

23&24

LAMP TEMP

Photometer Option

25&26

O3 LAMP TEMP

Ozonator Option

27&28

INTENSITY

Photometer Option

29&30

NOISE

Photometer Option

31&32

ANALOG 1

I/O Expansion Board Option

33&34

ANALOG 2

I/O Expansion Board Option

35&36

ANALOG 3

I/O Expansion Board Option

37&38

ANALOG 4

I/O Expansion Board Option

39&40

ANALOG 5

I/O Expansion Board Option

41&42

ANALOG 6

I/O Expansion Board Option

43&44

ANALOG 7

I/O Expansion Board Option

45&46

ANALOG 8

I/O Expansion Board Option

Thermo Fisher Scientific

Register
Number

Variable

Used Exclusively In

47&48

PERM GAS TMP

Permeation Span Source Option

49&50

EXT ALARMS

Read Coils for 146i

Thermo Fisher Scientific

Coil
Number

Status

Used Exclusively In

NONE

GAS BIT 1

GAS BIT 2

GAS BIT 3

SPAN BIT 1

SPAN BIT 2

SPAN BIT 3

O3/PERM BIT 1

Ozonator or Permeation Span Source Option

O3/PERM BIT 2

Ozonator or Permeation Span Source Option

O3/PERM BIT 3

Ozonator or Permeation Span Source Option

10

O3/PERM BIT 4

Ozonator or Permeation Span Source Option

11

PHOTO BIT 1

Photometer Option

12

PHOTO BIT 2

Photometer Option

13

GAS A

14

GAS B

15

GAS C

16

GAS D

Six Valve Option

17

GAS E

Six Valve Option

18

GAS F

Six Valve Option

19

OZONATOR

Ozonator Option

20

PERM OVEN

Permeation Span Source Option

21

USER 1

22

USER 2

23

USER 3

24

USER 4

25

USER 5

26

USER 6

Six Valve Option

iSeries Manual Update Addendum

67

Coil
Number

Status

Used Exclusively In

27

USER 7

28

USER 8

29

GEN ALARM

30

AMBIENT TEMP

31

O3 LAMP TEMP

Ozonator Option

32

PERM GAS
TEMP

Permeation Span Source Option

33

PRESSURE

Photometer Option

34

PHOT BENCH
TEMP

Photometer Option

35

PHOT LAMP
TEMP

Photometer Option

36

PHOT
INTENSITY

Photometer Option

37

O3 LEVEL

Photometer Option

38

MB STATUS

39

MIB STATUS

40

I/O BD STATUS

41

LOCAL/REMOTE

42

SERVICE

43

EXT ALARM 1

44

EXT ALARM 1

45

EXT ALARM 1

46

STANDBY

I/O Expansion Board Option

Write Coils for 146i

68

iSeries Manual Update Addendum

Coil
Number

Action

Coil Group

100

NONE

101

GAS BIT 1

Gas Bit

102

GAS BIT 2

Gas Bit

103

GAS BIT 3

Gas Bit

104

SPAN BIT 1

Span Bit

105

SPAN BIT 2

Span Bit

Used Exclusively In

Six Valve Option

Thermo Fisher Scientific

Coil
Number

Action

Coil Group

Used Exclusively In

106

SPAN BIT 3

Span Bit

107

O3/PERM BIT 1

O3 Perm Bit

Ozonator or Permeation Span Source

Option

108

O3/PERM BIT 2

O3 Perm Bit

Ozonator or Permeation Span Source

Option

109

O3/PERM BIT 3

O3 Perm Bit

Ozonator or Permeation Span Source

Option

110

O3/PERM BIT 4

O3 Perm Bit

Ozonator or Permeation Span Source

Option

111

PHOTO BIT 1

Photo Bit

Photometer Option

112

PHOTO BIT 2

Photo Bit

Photometer Option

113

AOUTS TO ZERO

Analog Out Test

I/O Expansion Board Option

114

AOUTS TO FS

Analog Out Test

I/O Expansion Board Option

115

EXT ALARM 1

116

EXT ALARM 2

117

EXT ALARM 3

5020i
Read Registers for 5020i

Thermo Fisher Scientific

Register
Number

Variable

NONE

1&2

CONTINUOUS SO2

3&4

CONTINUOUS SO4

5&6

BATCH SO4

7&8

F0 AVERAGE

9&10

F0 STD DEV

11&12

F0 POINTS

13&14

F1 AVERAGE

15&16

F1 STD DEV

17&18

F1 POINTS

19&20

SMP AVERAGE

21&22

SMP STD DEV

23&24

SMP POINTS

Used Exclusively In

iSeries Manual Update Addendum

69

Register
Number

Variable

Used Exclusively In

25&26

FILTER BKG

27&28

INT TEMP

29&30

CHAMBER TEMP

31&32

CNV TEMP TOP

33&34

CNV TEMP BTM

35&36

PERM OVEN GAS

Internal Zero/Span Perm Span Source Option

37&38

PERM OVEN HTR

Internal Zero/Span Perm Span Source Option

39&40

CHAMBER
PRESSURE

41&42

SAMPLE FLOW

43&44

PMT VOLTS

45&46

FLASH VOLTS

47&48

FLASH REF

49&50

ANALOG IN 1

I/O Expansion Board Option

51&52

ANALOG IN 2

I/O Expansion Board Option

53&54

ANALOG IN 3

I/O Expansion Board Option

55&56

ANALOG IN 4

I/O Expansion Board Option

57&58

ANALOG IN 5

I/O Expansion Board Option

59&60

ANALOG IN 6

I/O Expansion Board Option

61&62

ANALOG IN 7

I/O Expansion Board Option

63&64

ANALOG IN 8

I/O Expansion Board Option

65&66

CONV FLOW

67&68

AMBIENT TEMP

69&70

AMBIENT PRES

71&72

SO2 CAL COEF

73&74

SO2 CAL BKG

75&76

EXT ALARMS

77&78

STP/AMBIENT

Read Coils for Model 5020i

70

iSeries Manual Update Addendum

Coil
Number

Status

NONE

Used Exclusively In

Thermo Fisher Scientific

Thermo Fisher Scientific

Coil
Number

Status

SERVICE

ZERO MODE

SPAN MODE

SAMPLE MODE

FILTER MODE

PURGE MODE

GEN ALARM

SO4 CONC ALARM (MAX)

SO4 CONC ALARM (MAX)

10

INT TEMP ALARM

11

CHAMB TEMP ALARM

12

CONV TEMP ALARM

13

CONV TEMP DIFF ALARM

14

PERMEATION SPAN
SOURCE TEMP ALARM

15

AMB TEMP ALARM

16

AMB PRESSURE ALARM

17

CHAMB PRESSURE
ALARM

20

SAMPLE FLOW ALARM

21

CONVERTER FLOW
ALARM

22

FLASH REF ALARM

23

FLASH VOLTAGE ALARM

24

AUTO TIMING ALARM

25

DATA WARNING ALARM

26

ZERO CHK/CAL ALARM

27

SPAN CHK/CAL ALARM

28

MB STATUS ALARM

29

MIB STATUS ALARM

30

I/O BD STATUS ALARM

31

EXT CONV BD STATUS

ALARM

32

LOCAL/REMOTE

Used Exclusively In

I/O Expansion Board Option

iSeries Manual Update Addendum

71

Coil
Number

Status

33

EXT ALARM 1

34

EXT ALARM 2

35

EXT ALARM 3

Used Exclusively In

Write Coils for 5020i

72

Coil
Number

Action Triggered

Coil Group

Used
Exclusively In

100

NONE

101

ZERO MODE

Zero/Span Mode

102

SPAN MODE

Zero/Span Mode

103

SAMPLE MODE

Sample/Filter Mode

104

FILTER MODE

Sample/Filter Mode

105

SET BACKGROUND

106

CAL TO SPAN

107

AOUTS TO ZERO

Analog Output Test

I/O Expansion
Board Option

108

AOUTS TO FS

Analog Output Test

I/O Expansion
Board Option

109

EXT ALARM 1

110

EXT ALARM 2

111

EXT ALARM 3

Geysitech (BayernHessen) Protocol

Appendix

This section describes the updates and corrections that apply to the
Geysitech (Bayern-Hessen) Protocol appendix.

Update Serial
Communication Parameters

Update the Serial Communication Parameters section as follows:

iSeries Manual Update Addendum

Number of Data bits

: 7 or 8

Number of Stop bits

: 1 or 2

Parity

: None, Odd, or Even

Data rate

: 1200 to 115200 Baud (9600 is default)

Thermo Fisher Scientific

Add Connection Information

Add the following to the TCP Communication Parameters section:

Up to three simultaneous connections are supported over Ethernet.

Add Basic Command Structure

Add the following to the Basic Command Structure section:

Block Check Characters <BCC> may be added to the command to
prevent processing invalid commands.

Change Block Checksum

Change the Block Checksum <BCC> heading to Block Checksum

Characters <BCC>.
In the first sentence of the description change The block checksum is to
The Block Checksum Characters are.

Add Serial Number Field

A Geysitech serial number has been added in the response to a Geysitech

protocol DA command. In the Basic Command Structure section,
replace the last example in the section with the following text and two
examples:
The Geysitech serial number defaults to zero. To set the Geysitech serial
number select Main Menu > Instrument Controls > Communication
Settings > Geysitech Serial No.

Example of response to DA command from an instrument with Geysitech

serial number set to 000. The Geysitech serial number is bold in the
example.
Geysitech Protocol with transmission of three concentrations (Instrument
ID is 1, Operation Status is 03, Error Status is 04):
Data Query String:

<STX>DA<CR>

Reply String:

<STX>MD03<SP>001<SP>+2578+01<SP>03 <SP>04<SP>0000000000 <SP>002 <SP>

Address First Concentration(E-format)=25.78

Address+1

+5681+00<SP>03<SP>04<SP>000 0000000<SP>003<SP>+1175+01<SP>03<SP>04<SP

Second Concentration = 5.681

Address+2

Third Concentration=11.75

0000000000<SP><CR>

Thermo Fisher Scientific

iSeries Manual Update Addendum

73

Example of response to DA command from an instrument with Geysitech

serial number set to 123.
Data Query String:

<STX>DA<CR>

Reply String:

<STX>MD03<SP>001<SP>+2578+01<SP>03 <SP>04<SP>1230000000 <SP>002 <SP>

Address First Concentration(E-format)=25.78

Address+1

+5681+00<SP>03<SP>04<SP>123 0000000<SP>003<SP>+1175+01<SP>03<SP>04<SP

Second Concentration = 5.681

Address+2

Third Concentration=11.75

1230000000<SP><CR>

Updates for Specific Manuals

The following updates apply to only the specific manuals listed.

42i
Change Default Chamber Temp
Control/Alarm Limits
Ozonator Safety Update

In the Operation chapter at Main Menu > Alarms > Chamber Temp,
change the default chamber temperature control/alarm limit references in
associated text and screens from 47 C to 48 C and 51 C to 52 C.
In the Operation chapter at Main Menu > Service > Ozonator Safety,
add the following highlighted text to the first paragraph as indicated in the
following example:
The Ozonator Safety screen is used to turn the ozonator safety feature on
or off. If the ozonator safety is turned off, the ozonator will always be on,
even if the converter is not up to temperature. The ozonator shuts off if
there is a converter temperature alarm or an ozone flow alarm. If the safety
override is on, the instrument generates an ozone flow alarm.

74

iSeries Manual Update Addendum

Thermo Fisher Scientific

42i TL
Monitoring Signals Update

In the System Description chapter, at the Monitoring Signals

description, replace the second paragraph with the following:
In auto mode, every ten seconds the NO/NOx solenoid and the Prereactor
solenoid switch and the processor waits three seconds for the reaction
chamber to flush and stabilize. After those three seconds, it accumulates the
signal counts for seven seconds before again switching the solenoids. This
results in three raw signals: NO, NOx, and Prereactor.

Measurement Calculations
Update

In the System Description chapter, at the Measurement Calculations

description, replace the first sentence with the following:
The calculation of the NO, NOx, and Prereactor concentrations is lengthy
and uses the high-level processor to provide the most accurate readings.
In the System Description chapter, at the Measurement Calculations
description, replace the first two sentences of the second paragraph with the
following:
Next, the uncorrected NO, NOx, and Prereactor values are determined
according to a unique averaging algorithm which minimizes errors resulting
from rapidly changing concentrations. This algorithm results in NO, NOx,
and Prereactor values which are stored in RAM in a circular buffer that
holds all the ten second data from the previous five minutes.
In the System Description chapter, at the Measurement Calculations
description, replace the first two sentences of the third paragraph with the
following:
The background values for NO, NOx, and Prereactor which are corrected
for pressure and temperature are subtracted from their respective averages.
The Prereactor value is then subtracted from the NO and NOx values to
provide dynamic background correction. The NO reading is corrected by
the stored span factor and by the pressure and temperature factors.

42i TL and 42i Y

Add Ranges to Specifications

In the Introduction chapter, add 500 and 1000 ppb, and 500 and 1000
g/m3 to the Specifications table as shown in the highlighted example that
follows:
Table 14. Model 42i Trace Level Specifications

Preset ranges

Thermo Fisher Scientific

0-5, 10, 20, 50, 100, 200, 500, 1000 ppb

0-10, 20, 50, 100, 200, 500, 1000, 2000 g/m3

iSeries Manual Update Addendum

75

Add Displayed Pressure is

Measured in Pre-reactor Mode

In the Operation chapter, at Main Menu > Instrument Controls, add

The displayed pressure is measured in pre-reactor mode. as shown in the
highlighted example that follows:
When pressure compensation is on, the first line of the display represents
the current pressure in the reaction chamber. When pressure compensation
is off, the first line of the display shows the factory standard pressure of 300
mmHg. The displayed pressure is measured in pre-reactor mode.

42i, 42i HL, 42i LS, 42i TL, 42i Y, and 17i
Add Note to Streaming
Data Configuration

In the Operation chapter, at Main Menu > Instrument Controls >

Communication Settings > Streaming Data Config, add the following
note:
Note The selected item list is different depending on the
AUTO/MANUAL MODE and RANGE MODE settings. Changing
either of these settings will produce a different set of streaming data items.
If either of these modes is going to be changed on a regular basis, then the
user must configure each set of data separately after changing the modes to
each setting.

Add Note to Analog

Output Configuration

In the Operation chapter, add the following note at Main Menu >
Instrument Controls > I/O Configuration > Analog Output Config; and
also at Main Menu > Instrument Controls > I/O Configuration > Analog
Output Config > Select Channel > Choose Signal To Output:
Note The settings are different depending on the AUTO/MANUAL
MODE and RANGE MODE settings. Changing either of these settings
will produce a different set of analog output data items. If either of these
modes is going to be changed on a regular basis, then the user must
configure each set of data separately after changing the modes to each
setting.

76

iSeries Manual Update Addendum

Thermo Fisher Scientific

42i, 42i LS, 42i NOx, 43i HL

Add Rebuild Procedure
for New Version Pump

A new version pump has been added to the 42i, 42i LS, 42i NOx, and 43i
HL. This pump is interchangeable with the old pump. It retains the same
part number, but requires a different repair kit. The new version pump
includes the repair kit part number of the on the pump label, the old pump
does not.
This section provides the repair procedure for the new version pump and
includes a pump rebuild kit part number to be added to the Replacement
Parts List in the Servicing chapter.

New Version Pump

In the Preventive Maintenance chapter at Pump Rebuilding, add the

following rebuilding procedure for the new version pump.
Use the following procedure to rebuild the pump. Refer to the illustration.
Equipment Required:
Pump repair kit
Equipment Damage Some internal components can be damaged by small
amounts of static electricity. A properly ground antistatic wrist strap must
be worn while handling any internal component.

Thermo Fisher Scientific

iSeries Manual Update Addendum

77

Disassembly

1. Turn instrument OFF, unplug the power cord, and remove the cover.
2. The compressor housing cover must be removed to gain access to the
inside of the compressor housing. Remove the four compressor housing
cover screws and then remove the cover. Re-use any gasketing. Remove
any debris that may have accumulated in the bottom of the compressor
housing.
3. Remove the four top plate screws and remove the top plate. Note the
positioning of the flapper plate relative to the valve ports on the top
plate and bottom plate. Lift off the flapper plate.
4. Remove the bottom plate.
5. Check that all parts are free from dirt and clean as necessary. DO NOT
scratch the parts.
6. Removal of the old diaphragm: Rotate the fan so that the diaphragm
is positioned at the top dead center. This will help unseat the edge of
the diaphragm. If required, push up from underneath the diaphragm or
use a non-metallic tool to pry up the diaphragm from the housing
groove. Unscrew the old diaphragm by turning it counterclockwise
using both hands. DO NOT use tools!
Note Take care not to lose the shim rings positioned between the
diaphragm and connecting rod, as the same shim rings must be used during
re-assembly.

Assembly with New 1. Place the shim rings removed in the previous step onto the threaded
Diaphragm and Valve
stud of the new diaphragm. Carefully screw the new diaphragm into
the connecting rod. Turn the diaphragm until is snug, then lift and
grip the edges of the diaphragm at 7 and 2 oclock and tighten firmly
using both hands. DO NOT use tools!
2. Turn the fan until the diaphragm is flat across (mid-point of the
stroke). With the diaphragm centered over the compressor housing,
firmly seat the diaphragm edge into the compressor housing groove.

78

iSeries Manual Update Addendum

Thermo Fisher Scientific

3. Place the clean bottom plate onto the compressor housing using the
reference mark made earlier to ensure the correct orientation. Then
place the new flapper on top of the intermediate plate.

Figure x-x. Rebuilding the Pump

4. Place the clean top plate on top of the bottom plate using the reference
mark made earlier to ensure the correct orientation. Tighten the four
top plate screws snugly in a diagonal pattern and then tighten to a
maximum torque of 6-7 inch-lbs. Turn the fan by hand to confirm that
the pump turns freely.

Thermo Fisher Scientific

iSeries Manual Update Addendum

79

5. Replace the compressor housing cover and gasket. Install the four cover
screws. Do not over-tighten.
Add Part Number of New Version
Pump to Replacement Parts List

In the Servicing chapter at Replacement Parts List, add the following

part number and description of the new version pump repair kit below the
existing pump repair kit part number as follows:

107751-00

Pump Repair Kit (for pump 101011-00 new version)

43i, 43i TLE, 48i, 48i TLE, 48i HL, 410i, 450i,
and 5020i
Add Rebuild Procedure
for New Version Pump

A new version pump has been added to the 43i, 43i TLE, 48i, 48i HL,
410i, 450i, and 5020i. This pump is interchangeable with the old pump. It
retains the same part number, but requires a different repair kit. The new
version pump includes the repair kit part number on the pump label, the
old pump does not.
This section provides the repair procedure for the new version pump and
includes a pump rebuild kit part number to be added to the Replacement
Parts List in the Servicing chapter.

New Version Pump

In the Preventive Maintenance chapter at Pump Rebuilding, add the

following rebuilding procedure for the new version pump.
Use the following procedure to rebuild the pump.
Equipment Required:
Pump repair kit

80

iSeries Manual Update Addendum

Thermo Fisher Scientific

Equipment Damage Some internal components can be damaged by small

amounts of static electricity. A properly ground antistatic wrist strap must
be worn while handling any internal component.
Disassembly

1. Turn instrument OFF, unplug the power cord, and remove the cover.
Make a sketch of the position of any tubes and fittings for ease of reassembly later.
2. Mark the position of the pump top plate, bottom plate and compressor
housing relative to each other by drawing a line on the edges with a
pencil or marker to ensure proper re-assembly.
3. The aluminum compressor housing cover must be removed to gain
access to the inside compressor housing. Remove the four screws and
then remove the cover. Re-use any gasketing. Remove any debris that
may have accumulated in the bottom of the compressor housing.
4. Remove the four top plate screws and remove the top plate. Note the
positioning of the flapper valve relative to the valve ports on the top
plate and bottom plate. Lift off the flapper valve.
5. Remove the bottom plate.
6. Check that all parts are clean from dirt and clean as necessary. DO
NOT scratch the parts.
7. Removal of the old diaphragm: Rotate the fan so that the diaphragm
is positioned at the top dead center. This will help unseat the edge of
the diaphragm. If required, push up from underneath the diaphragm or
use a non-metallic tool to pry up the diaphragm from the housing
groove. Unscrew the old diaphragm by turning it counterclockwise
using both hands. DO NOT use tools!
Note Take care not to lose the shim rings positioned between the
diaphragm support cup and connecting rod, as the same shim rings must
be used during re-assembly.
While unscrewing the diaphragm with one hand, use your other hand
to secure the support cup and shim ring(s) onto the diaphragm stud.
Lift the diaphragm, support cup and shim ring(s) from the pump.

Thermo Fisher Scientific

iSeries Manual Update Addendum

81

The compressor housing cover must be removed to gain access to and

secure the support cup and shim ring(s) onto the stud. Note that the
quantity and thickness of the shim ring(s) will vary from pump to
pump. Parts removed must be replaced exactly as found. If repairing
multiple pumps, take care not to mix parts.

Figure x-x. Rebuilding the Pump

Assembly with New 1. Place the parts removed in the previous step onto the threaded stud of
the new diaphragm. Carefully screw the new diaphragm into the
Diaphragm and Valve
connecting rod. Secure the support cup and small parts onto the
diaphragm stud using a technique similar to that used during removal.
It is helpful to hold the connecting rod at a slight angle until the
threads are started. Spin the diaphragm on until it is snug, then lift and
82

iSeries Manual Update Addendum

Thermo Fisher Scientific

grip the edges of the diaphragm at 7 and 2 oclock and tighten firmly
using both hands. DO NOT use tools!
Tip: If the pump is loose and not mounted, position and hold the pump
with the motor shaft vertical when starting the threaded diaphragm stud
into the connecting rod. This helps to prevent the small parts from falling
off the stud.
2. Turn the fan until the diaphragm is flat across (mid-point of the
stroke). With the diaphragm centered over the compressor housing,
firmly seat the diaphragm edge into the compressor housing groove.
3. Place the clean bottom plate onto the compressor housing using the
reference mark made earlier to ensure the correct orientation. Then
place the new flapper on top of the intermediate plate.
4. Place the clean top plate on top of the bottom plate using the reference
mark made earlier to ensure the correct orientation. Tighten the four
top plate screws snugly in a diagonal pattern and then tighten to a
maximum torque of 6-7 inch-lbs. Turn the fan by hand to confirm that
the pump turns freely.
5. Replace the compressor housing cover and gasket. Install the four cover
screws. Do not over-tighten.
Add Part Number of New Version
Pump to Replacement Parts List

In the Servicing chapter at Replacement Parts List, add the following

part number and description of the new version pump repair kit below the
existing pump repair kit part number as follows:

108002-00

Pump Repair Kit (for pump 101426-00 new version)

43i, 43i TL, 48i, 48i HL, 48i TLE, 49i, 49i PS,
146i, 410i, 450i, 5020i and 42i NOy
Add Rebuild Procedure for
New Shimless Version Pump

A new version pump has been added to the 43i, 43i TL, 48i, 48i HL, 48i
TLE, 49i, 49i PS, 146i, 410i, 450i, 5020i, and 42i NOy. This pump is
interchangeable with the old pump. It has a new part number 111553-00
and uses the same rebuild kit as the new version pump. The new shimless
version pump includes the repair kit part number on the pump label.
This section provides the repair procedure for the new shimless version
pump and includes a pump rebuild kit part number to be added to the
Replacement Parts List in the Servicing chapter.

Thermo Fisher Scientific

iSeries Manual Update Addendum

83

New Shimless
Version Pump

In the Preventive Maintenance chapter at Pump Rebuilding, add the

following rebuilding procedure for the new version pump.
Use the following procedure to rebuild the pump.
Equipment Required:
Pump repair kit
Equipment Damage Some internal components can be damaged by small
amounts of static electricity. A properly ground antistatic wrist strap must
be worn while handling any internal component.
Disassembly

1. Turn instrument OFF, unplug the power cord, and remove the cover.
Make a sketch of the position of any tubes and fittings for ease of reassembly later.
2. Mark the position of the pump head plate, intermediate plate and
compressor housing relative to each other by drawing a line on the
edges with a pencil or marker to ensure proper re-assembly.
3. The aluminum compressor housing cover must be removed to gain
access to the inside of the compressor housing. Remove the four screws
and then remove the cover. Re-use any gasketing. Remove any debris
that may have accumulated in the bottom of the compressor housing.

84

iSeries Manual Update Addendum

Thermo Fisher Scientific

4. Remove the four socket cap screws and remove the head plate. Note
the positioning of the valve plate relative to the valve ports on the head
plate and intermediate plate. Lift off the valve plate.
5. Remove the intermediate plate.
6. Check that all parts are clean from dirt and clean as necessary. DO
NOT scratch the parts.
7. Removal of the old diaphragm: Rotate the fan so that the diaphragm
is positioned at the top dead center. This will help unseat the edge of
the diaphragm. If required, push up from underneath the diaphragm or
use a non-metallic tool to pry up the diaphragm from the housing
groove. Unscrew the old diaphragm by turning it counterclockwise
using both hands. DO NOT use tools!
Lift the diaphragm from the pump. Parts removed must be replaced
exactly as found. If repairing multiple pumps, take care not to mix
parts.

Figure x-x. Rebuilding the Pump

Thermo Fisher Scientific

iSeries Manual Update Addendum

85

Assembly with New 1. Carefully screw the new diaphragm (no shims are needed) into the
connection rod. Secure the support cup and small parts onto the
Diaphragm and Valve
diaphragm stud using a technique similar to that used during removal.
It is helpful to hold the connecting rod at a slight angle until the
threads are started. Spin the diaphragm on until it is snug, then lift and
grip the edges of the diaphragm at 7 and 2 oclock and tighten firmly
using both hands. DO NOT use tools!
2. Turn the fan until the diaphragm is flat across (mid-point of the
stroke). With the diaphragm centered over the compressor housing,
firmly seat the diaphragm edge into the compressor housing groove.
3. Place the clean intermediate plate onto the compressor housing using
the reference mark made earlier to ensure the correct orientation. Then
place the new valve plate on top of the intermediate plate.
4. Place the clean head plate on top of the intermediate plate using the
reference mark made earlier to ensure the correct orientation. Tighten
the four socket cap screws snugly in a diagonal pattern and then tighten
to a maximum torque of 6-7 inch-lbs. Turn the fan by hand to confirm
that the pump turns freely.
5. Replace the compressor housing cover and gasket. Install the four cover
screws. Do not over-tighten.
Add Part Number of New In the Servicing chapter at Replacement Parts List, add the following
Shimless Version Pump to part number and description of the new version pump repair kit below the
Replacement Parts List existing pump repair kit part number as follows:

108002-00

Pump Repair Kit (for pump 111553-00 new shimless version)

42i and 43i - All Variants

In the Operation chapter, remove Cal Pressure screens (because they
were never used), under calibration menus, as shown in the following
example:

86

iSeries Manual Update Addendum

Thermo Fisher Scientific

42i, 43i, and 48i - All Variants

Add Setup Run Screens

Add Setup Run Screens to the Service menu as follows:

Setup Run Screens

The Setup Run Screens menu is used to define and edit up to five custom
Run screens. The Setup Run Screens menu is visible only when the
instrument is in the Service mode.
Custom Run Screen

Title Bar

INTT

DIAGNOSTICS

31.4C
mm

Pres

Instrument Readings

750.0Hg
l/

Flow
SAMPLE
RANGE

0.0min
11:27
AVG

DIAGS ALARM

In the Main Menu, choose Service > Setup Run Screens.

SELECT RUN SCREEN:
>RUN SCREEN 1
RUN SCREEN 2
RUN SCREEN 3
RUN SCREEN 4
RUN SCREEN 5
RANGE

Thermo Fisher Scientific

AVG

DIAGS ALARM

iSeries Manual Update Addendum

87

The Select Run Screen menu is used to display the Run screen editor.

Edit Run Screen

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen.

The Edit Run Screen menu is used to edit the contents of the custom run
screen. This menu allows the user to edit the run screen title, toggle the run
screen ON and OFF, and specify the number of items to be displayed on
the Run screen (1-10).
Edit Run Screen
EDIT RUN SCREEN:
>EDIT TITLE
ENABLED
NUMBER OF ITEMS
ITEM 1
ITEM 2
RANGE

AVG

DIAGS ALARM

ITEM 8

Edit Title

OFF
8
TEMP
PRES

FLOW

The Edit Title screen is used to edit the contents of the title bar on the
selected Custom Run screen.

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen > Edit Title.
EDIT RUN SCREEN TITLE:
DIAGNOSTICS
ABCDEFGHIJKLMN
OPQRSTUVWXYZ
0123456789 ./RANGE

AVG

BKSP
PAGE
SAVE

DIAGS ALARM

Use
,
,
, and
to position the cursor on the title,
the characters, and the BKSP, PAGE, and SAVE selections. Use
to
select a character or the BKSP, PAGE, and SAVE selections.
The BKSP selection is used to backspace the cursor in the title. The PAGE
selection toggles the characters between upper case and lower case. The
SAVE selection is used to save changes made to the title.
Enabled

88

iSeries Manual Update Addendum

The Enabled screen is used to toggle the selected custom Run screen ON
and OFF. When a Run screen is ON, it will be displayed on Run screen
when using
to scroll through the available Run screen
displays. When a Run screen is OFF, it will be skipped when scrolling

Thermo Fisher Scientific

through the Run screen displays. For example, if Run screens 2 and 3 are
set to OFF, and Run screens 1, 4, and 5 are ON, scrolling down through
the available Run screen displays will display only Run screens 1, 4, and 5.

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen > Enabled.
ENABLE/DISABLE RUN SCREEN:
CURRENTLY:
OFF
SET TO:
ON ?
TOGGLE VALUE
RANGE

Number of Items

AVG

DIAGS ALARM

The Number of Items menu selection is used to set the number of

instrument readings to display on the custom Run screen. A maximum of
10 items can be displayed on the Run screen. A Run screen configured for
5 items or less displays the items in the large font; a Run screen with 6-10
items displays the items in the small font.

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen > Number of Items.
SET NUMBER OF ITEMS:
CURRENTLY:
5
SET TO:
4
CHANGE VALUE

RANGE

Item Number

AVG

SAVE

DIAGS ALARM

The Item number menu selection is used to assign a selected parameter to a

position in the Run screen display list. Item 1 is displayed at the top of the
list. If None is selected, the associated item will not be displayed on the
Run screen.
Note The Analog Inputs selection is displayed only if the optional I/O
expansion board is installed.

Thermo Fisher Scientific

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen > Item number.

iSeries Manual Update Addendum

89

SELECT RUN SCREEN ITEM:

CONCENTRATIONS
OTHER MEASUREMENTS
ANALOG INPUTS

RANGE

Concentrations

AVG

DIAGS ALARM

The Concentrations screen is used to display a list of concentration

parameters that can be specified for the selected item number.

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen > Item number > Concentrations.

42i Screen
CONCENTRATIONS:
>NONE
NO
NO2
NOx
LO NO
LO NO2
LO NOx
RANGE

AVG

<--

DIAGS ALARM

HI NO
HI NO2
HI NOx
RANGE (NOX)

43i Screen
CONCENTRATIONS:
>NONE
SO2
LO SO2
HI SO2
RANGE (SO2)

RANGE

90

iSeries Manual Update Addendum

AVG

<--

DIAGS ALARM

Thermo Fisher Scientific

48i Screen
CONCENTRATIONS:
>NONE
CO
RANGE STATUS

RANGE

Other Measurements

AVG

<--

DIAGS ALARM

The Other Measurements screen is used to display a list of nonconcentration parameters that can be specified for the selected item
number.

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen > Item number > Other Measurements.

42i Screen
OTHER MEASUREMENTS:
>NONE
INT TEMP
CHAMBER TEMP
COOLER TEMP
NO2 CNV TEMP
PERM VON GAS
PERM OVN HTR
RANGE

AVG

DIAGS ALARM

CHAMBER PRES
FLOW
PMT VOLTS
OZONATOR FLOW

43i Screen
OTHER MEASUREMENTS:
>NONE
INT TEMP
<-CHAMBER TEMP
PERM OVN GAS
PERM OVN HTR
CHAMBER PRES
SAMPLE FLOW
RANGE

Thermo Fisher Scientific

AVG

DIAGS ALARM

iSeries Manual Update Addendum

91

48i Screen
OTHER MEASUREMENTS:
>NONE
S/R
INTERNAL TEMP
CHAMBER TEMP
CHAMBER PRES
SAMPLE FLOW
INTENSITY
RANGE AVG
MOTOR SPEED

Analog Inputs

<--

DIAGS ALARM

The Analog Inputs screen is used to display a list of analog inputs that can
be specified for the selected item number.

In the Main Menu, choose Service > Setup Run Screens > Select a Run
Screen > Item number > Analog Inputs.
ANALOG INPUTS:
>NONE
ANALOG IN 1
ANALOG IN 2
ANALOG IN 3
ANALOG IN 4
RANGE

AVG

DIAGS ALARM

ANALOG IN 8

42i, 43i, 43i TLE and 146i

Change Perm Oven
Calibration Resistance

In the Optional Equipment chapter of instruments with the perm oven

option, change the value of the resistance used in the procedures from 3.8K
Ohms to 4.2K Ohms.

43i All Variants

Change Set PMT Voltage

92

iSeries Manual Update Addendum

In the PMT Voltage Adjustment section of the Operation chapter,

change the Set PMT voltage to include a minus sign as shown in the
highlighted example that follows:

Thermo Fisher Scientific

SET PMT VOLTAGE:

SET PMT:
COUNTS:

-XXX.X V
2254

INC/DEC

SAVE VALUE
RANGE

Change PMT Supply Voltage

AVG

DIAGS ALARM

In the Interface Board Voltages section of the Operation chapter,

change the PMT Supply voltage to include a minus sign as shown in the
highlighted example that follows:
INTERFACE BOARD VOLTAGES:
PMT SUPPLY
-XXX.X V
FLASH SUPPLY
1000.0 V
3.3 SUPPLY
3.3 V
5.0 SUPPLY
5.0 V
15.0 SUPPLY
15.0 V
-15.0 SUPPLY
-15.0 V
24.0 SUPPLY
24.0 V
RANGE

Add Teflon Particulate Filter

DIAGS ALARM

In the Replacement Parts List of the Servicing chapter, add the Teflon
particulate filter option, if it is not already included:
102701-00

Replace Input Board Description

and Part Number

AVG

Teflon particulate filter (option)

In the Replacement Parts List of the Servicing chapter, replace the

input board description and part number so that it will include the case:
102273-00

Input Board Assembly

43i HL
Heated Kicker Option

Add information for the heated kicker option to the 43i HL instruction
manual as follows:
Add the following heated kicker description and part number to the
Replacement Parts List in the Servicing chapter:
104123-00

Thermo Fisher Scientific

Kicker Assembly, Heated (optional)

iSeries Manual Update Addendum

93

Add the following heated kicker replacement procedure to the Servicing

chapter:

Heated Kicker
Replacement

Use the following procedure to replace the optional heated kicker assembly.
Equipment Required:
Heated kicker assembly (optional)
Allen wrench, 5/32-inch
Equipment Damage Some internal components can be damaged by small
amounts of static electricity. A properly ground antistatic wrist strap must
be worn while handling any internal component.
1. Turn instrument OFF, unplug the power cord, and remove the cover.
2. Using a 5/32-inch Allen wrench, remove the four optical bench
retaining screws.
3. Disconnect the plumbing connections as appropriate to gain enough
clearance to lift the optical bench off the heated kicker. Carefully note
the plumbing connections to facilitate reconnection.
4. Remove the heated kicker from the optical bench.
5. Install the new heated kicker assembly.
6. Reposition the optical bench on top of the heated kicker, insert and
tighten the four optical bench retaining screws, and reconnect any
plumbing connections by following the previous steps in reverse order.
7. Calibrate the instrument. Refer to the Calibration chapter in this
manual.

94

iSeries Manual Update Addendum

Thermo Fisher Scientific

Retaining Screws (4)

Heated Kicker

Replacing the Kicker Assembly (Optional Heated Kicker)

Add the following heated kicker description to the System Description

chapter:

Heated Hydrocarbon
Kicker (Optional)

The hydrocarbon kicker removes hydrocarbons from the gas stream while
leaving the SO2 concentration unaffected. It operates on a selective
permeation principle using differential pressure to force hydrocarbon
molecules to pass through the tube wall. The differential pressure is created
across the tube wall as sample gas passes through a capillary tube which
reduces its pressure. The sample gas is then fed to the shell side of the
hydrocarbon kicker.
The optional heated hydrocarbon kicker is used in applications requiring
more efficiency than the standard kicker. The heated kicker operates at the
same temperature as the optical bench and requires no additional power.

Add the following heated kicker description to the Optional Equipment

chapter:

Heated Hydrocarbon
Kicker

Thermo Fisher Scientific

The optional heated hydrocarbon kicker is used in applications requiring

increased efficiency. The heated kicker operates at the same temperature as
the optical bench and requires no additional power.

iSeries Manual Update Addendum

95

49i and 49i PS

Ozonator Solenoid

Add the following ozonator solenoid description to the Instrument

Controls menu in Chapter 3 following Custom Levels.
The Ozonator Solenoid screen is used to switch the ozonator solenoid on
and off. When the ozonator solenoid is on, the output of the internal
ozonator is fed into the analyzer. When the ozonator solenoid is off, the
output of the internal ozonator is fed to the manifold.

Add Pump Off to

Instrument Action List

For 49i PS, in Chapter 3 at Digital Input Settings > Select Relay >
Instrument Action, add Pump Off to the end of the Choose Action list.
For 49i PS, in Chapter 8 at the Digital Inputs section, add Pump Off
to the digital input list.

Remove References to
Ozonator Solenoid

For 49i PS, remove references to ozonator solenoid.

146i
Add Photometer Timer Note

Add the following note to Chapter 1 Photometer, Chapter 3 Run

Screen, Operation screen, Flow Modes, and Program > Events.
Note When the photometer is turned on, a 240-second countdown timer
is initiated to allow the photometer lamp to stabilize. No O3 measurements
are taken until this time has elapsed.

Add Note to Alarms Menu

Add Flow Controller

Calibration Note

If a particular subsystem is turned off, then its associated alarms will always
be evaluated as OK. For example, if the ozonator lamp is not up to
temperature, but the ozonator is turned off, then the ozonator lamp
temperature alarm will read as OK until the ozonator is turned on.
Add the following note to the Zero Flow Calibration description and the
Gas Flow Calibration description, in Chapter 3, under the Service section,
and to the Mass Flow Controllers procedure in Chapter 4:
Note Turn off the ozonator, permeation oven, and photometer functions
before performing a flow controller calibration, as these functions may
affect the measured flow at the manifold.

96

iSeries Manual Update Addendum

Thermo Fisher Scientific

Add Password Lock and

Service to Flags Map

Modify the Flags map, Figure B-1, to include Password Lock fourth bit
from the left, and Service - third bit from the left.

Figure B-1. Flags

Add Selections to Gas
Flow Controller

At the Gas Flow Controller topic in the Service Menu section of the
Operation chapter, add the following highlighted text to the end of the
second sentence:
Allowable selections are: 25, 50, 100, 200, and 500 sccm; and 5, 10, 15,
and 20 slm.

Change Gas Units to

Lower Case

Change gas units in the screens to lower case.

ppm

Thermo Fisher Scientific

iSeries Manual Update Addendum

97

5020i
Add STP/Ambient

98

iSeries Manual Update Addendum

Add STP/Ambient to the list of Other Measurements in the Datalogging

Settings menu, Streaming Data Configuration menu, and Analog Output
Configuration menu.

Thermo Fisher Scientific